betaFeedback

WorksPhysics and Astronomy

OpenFOAM computational fluid dynamics (CFD) solver for magnetohydrodynamic open cycles, applied to the Sakhalin pulsed magnetohydrodynamic generator (PMHDG)

Abstract

In the current study, we present a mathematical and computational fluid dynamics (CFD) model for simulating open-cycle linear Faraday-type continuous-electrode channels of magnetohydrodynamic (MHD) power generators, operating on combustion plasma. The model extends the Favre-averaged Navier-Stokes equations to account for the electric properties of the flowing plasma gas and its reaction to the applied magnetic field. The model takes into account various effects, such as the Lorentz force, turbulence, compressibility, and energy extraction from the plasma, and it adopts an electric potential technique along with the low magnetic Reynolds number (Rem) approximation. The model is numerically implemented using the multiphysics open-source computer programming environment "OpenFOAM," which combines the finite volume method (FVM) and the object-oriented programming (OOP) concept. The capabilities of the model are demonstrated by simulating the supersonic channel of the large-scale pulsed MHD generator (PMHDG) called "Sakhalin", with the aid of collected data and empirical expressions in the literature about its tested operation. Sakhalin was the world's largest PMHDG, with a demonstrated peak electric power output of 510 MW. Sakhalin operated on solid-propellant plasma (SPP), and it had a single supersonic divergent Faraday-type continuous-electrode channel with a length of 4.5 m. We check the validity of the model through comparisons with independent results for the Sakhalin PMHDG. Then, we process our three-dimensional simulation results to provide scalar characteristics of the Sakhalin channel, one-dimensional profiles along the longitudinal centerline, and three-dimensional distributions in the entire channel.

Introduction

Background

Sakhalin is the name of a Russian island in Northeast Asia with a conspicuously elongated form, located near the Japanese island of Hokkaido [1, 2]. Sakhalin is also the name of a powerful pulsed magnetohydrodynamic (MHD) generator that has been widely used and studied in the USSR (Union of Soviet Socialist Republics), with a demonstrated electric output of 510 MW during one of its performed tests. The Sakhalin pulsed MHD generator (PMHDG) was fueled by a solid propellant (pyrotechnic powder), and it contained a single linear continuous Faraday-type supersonic channel, with a length of 4.5 m [3, 4, 5]. The working medium for Sakhalin was hot-seeded weakly-ionized solid-propellant plasma (SPP). Continuous Faraday-type linear channels of MHG generators have two continuous electrodes placed opposite to each other. This particular linear channel design is a simpler configuration compared to other electric connection designs for linear channels [6]. Other (more-complicated) linear channel designs [7] are the segmented electrodes (segmented Faraday) design, the linear Hall design, and the diagonal design [8]. The Sakhalin was the world’s most powerful PMHDG, with a theoretical peak electric output power of 600 MW (this reduces to about 400 MW with a connected matched load) [9]. It was a self-contained system, not requiring connections to external supply sources [10]. The mass of the solid propellant charge was about 6000 kg (6 tonnes). The electrodes (negative anode and positive cathode) were graphite. A possible solid propellant is a mixture of powders having 64% Mg (magnesium), 35% KNO3_3 (potassium nitrate), and 1% technological additives (percentages are mass-based), pressed to a density of about 1700 kg/m3^3 [11]. The propellant can also be based on metal aluminum, rather than metal magnesium [12]. A small amount of alkali metal (cesium “Cs” or potassium “K”) is added to the solid propellant charge (the grain) to permit an appreciable level of ionization of the atoms of the seeded alkali metal (which changes phase to vapor at the high temperatures of the MHD channel) [13, 14]. Potassium (K) vaporizes at about 762 °C (1035 K), while cesium (Cs) vaporizes at about 682 °C (955 K) [15, 16, 17].

Pulsed magnetohydrodynamic generators (PMHDG) can be used to produce a powerful pulse of electricity for a few seconds. PMHDG can be used in geoelectric prospecting, where the produced electric pulse allows for estimating the electric resistivity of underground formations at different depths [18, 19, 20]. PMHDG may also be used to power electromagnetic rail launchers (railguns), where projectiles can be accelerated to speeds exceeding 2.5 km/s [21, 22]. PMHDG may also find applications in space systems [23, 24] and rocket propulsion [25, 26].

Besides Sakhalin, there were other solid-propellant plasma (SPP) PMHDG in the former USSR, but Sakhalin was by large the most powerful [27, 28, 29]. A comparison of different SPP-PMHDG that existed in the former USSR is presented in Table 1 [30, 31, 32].

Power system (ordered by power)Pamir-0-KTPamir-1PricaspiyPamir-3USoyuzUralKhybinySakhalin
Maximum electric power demonstrated (with an unmatched load), MW0.12020303140120500
Maximum electric power demonstrated (with a matched load), MW–101015163060400
Mobility–In containersMobile on a trackIn containersMobile on a trailer–In containersIn containers
Number of MHD channels12231121
Length of MHD channel(s), m11111.8–1.174.5
Operating duration for the load (duration of the pulse), sUp to 3.63–73–72.5–10Up to 1067–10Up to 7
Minimum pause between two runs, h–1212–12–1224
Approximate maximum possible mass flow rate of working fluid (plasma), kg/s2505024401002001000
Overall mass of the power system, tonne–8121825163450
Overall dimensions of the power system, m–4×1.5×24 \times1.5 \times24×1.5×24 \times1.5 \times2–7×2×27 \times2 \times2–8×7×1.58 \times7 \times1.513.5×3.7×2.713.5 \times3.7 \times2.7

Table 1. Comparison of different solid-propellant plasma (SPP) self-contained pulsed magnetohydrodynamic generators (PMHDG) in the former Union of Soviet Socialist Republics (USSR)

The table is not an exhaustive list. There were even additional SPP-PMHDG systems in the USSR, such as “Pamir” and “Pamir-06”.

Aside from the pulsed mode of magnetohydrodynamic (MHD) generators, they can also operate in a continuous mode as a non-conventional topping power cycle in a dual-cycle thermal power plant [33, 34, 35, 36]. MHD generators have a special feature of favoring elevated temperatures, which boost the electric conductivity in a rapid nonlinear fashion [37, 38, 39]. Other conventional power cycles (such as the Rankine-type steam cycle) can then be used as a bottoming cycle. In this case, the enormous unexploited heat in the exhaust hot gases leaving the topping MHD power cycle can be used to generate steam that drives steam turbines. These turbines are coupled with electromechanical generators. This dual-cycle concept is found in combined-cycle gas turbine (CCGT) power plants where a heat recovery steam generator (HRSG) is utilized to transfer heat from the higher-temperature topping gas cycle to the lower-temperature bottoming steam cycle [40, 41, 42].

The use of MHD generators, either pulsed or continuous, has an environmental advantage over fossil-fuel-fired power plants, where reducing the emissions of greenhouse gases (GHG) becomes possible, and this reduction helps in attenuating global warming [43, 44, 45, 46]. This possibility of GHG reduction when using MHD generators arises because the fuel and oxidizer combination in the case of combustion-plasma-based MHD generators can be selected such that the carbon dioxide (CO2\mathrm{CO}_2) dominates the exploited plasma gases that are leaving the MHD generator. This carbon dioxide enrichment facilitates its capture through the oxy-fuel carbon capture (OFCC) technology [47, 48, 49, 50]. The oxy-fuel technology is particularly attractive for MHD generators because this specialized combustion technique largely raises the temperature of the combustion flame and the combustion products. Therefore, the electric conductivity of the thermal-equilibrium “hot” plasma gas is improved. As a result, the electric output from the same volume flow rate of the plasma gas increases [51, 52]. In thermal-equilibrium “hot” plasma gas, atoms are ionized due to the temperature alone (unlike non-thermal “cold” plasma). Thus, higher temperatures increase the electric output from the same volume flow rate of the plasma gas [53, 54].

MHD generators also have the advantage of not having moving mechanical parts, which is unlike gas turbines, steam turbines, wind turbines, Stirling engines, and electromechanical generators that are commonly used in power generation [55, 56, 57, 58]. The simplicity of the design and the lack of complex fluid–structure interaction (FSI) and solid–solid contact eliminate the need for lubrication, bearing, and sealing elements [59, 60, 61]. MHD generators are direct power extraction (DPE) systems, like solar photovoltaic (PV) modules [62] and thermoelectric generators (TEG) modules, with no intermediate energy conversion processing needed [63, 64, 65, 66].

One more advantage of MHD generators operating with seeded combustion plasma is their flexibility with regard to the combusted fuel. Unlike conventional internal combustion engines (ICE), either reciprocating ones used in automobiles or turbomachinery ones used in jet airplanes, the MHD generator can be viewed as an external combustion engine (ECE). This is because the combustion of the fuel occurs outside the MHD channel, which is the primary energy conversion component (extracting thermal, pressure, and/or kinetic energy from the fluid and converting the fluid energy into direct-current “DC” electricity) [67, 68]. Because the combustion products (flue gases) act mainly as a bulk high-speed medium that carries the ionized alkali metal species and the liberated charge-carrying electrons, a wide variety of fuels can be used in the plasma generator (PG) combustor unit [69, 70, 71]. For example, green hydrogen [72, 73] (hydrogen produced through water electrolysis powered by renewable energy sources) may be exploited for this type of power generation [74, 75, 76, 77]. Gaseous fuels (such as natural gas) [78, 79, 80, 81]. Also, liquid fuels (such as kerosene) [82, 83, 84], and solid fuels (such as coal) are candidate sources of the plasma gases [85, 86]. Despite this flexibility, gas-fired and liquid-fired MHD generators have the advantage of not forming a slag layer (a layer of molten ash material that is solidified on the walls) over the electrodes of the MHD channel [87, 88, 89].

Examining recent research work in the field of magnetohydrodynamics (MHD) shows emphasis on theoretical problems, such as MHD flow over an oscillating vertical plate in a porous medium [90], MHD natural convection [91], MHD couple stress fluid [92], MHD with a lid-driven cavity [93], and MHD for a flat plate flow [94]. Although these MHD studies contribute to our understanding of the physics of MHD principles and explore interesting academic situations, they are far from impactful implementation in the energy sector to solve environmental challenges and meet societal needs. We here address this gap by focusing on a large-scale real-world use of our MHD knowledge through novel utility-scale electricity generation in a way that admits sustainability (using green hydrogen, for example, as a fuel), compactness (limited use of space), and effectiveness (a large amount of electricity can be produced).

Objectives

The first goal of this work is to present a proposed computational fluid dynamics (CFD) solver for continuous-electrode (continuous-Faraday) MHD channels, which is based on the OpenFOAM object-oriented programming (OOP) environment [95]. OpenFOAM is a popular collection of open-source CFD solvers for a wide variety of problems, which include compressible flows, incompressible flows, laminar flows, turbulent flows, multiphase flows, and reacting flows [96, 97, 98, 99]. OpenFOAM has been used in many applications in fluid dynamics [100, 101, 102], combustion [103], fluid–structure interaction (FSI) [104], and heat transfer [105]. OpenFOAM is based on the finite volume method (FVM) for discretizing the governing equations of the flow while attempting to enforce local conservation of mass, momentum, and energy at the level of a single computational cell (a single finite volume) [106, 107]. The proposed MHD channel solver in this study is a valuable tool in computer-aided design (CAD) of MHD channels with continuous electrodes, either operating in a pulsed mode or in a sustained mode. The solver may be further extended by the interested readers to add desired design alterations or explore different operating conditions such that one or more of the performance outputs can be controlled and optimized [108, 109]. For example, the influence of the area cross-section profile of the supersonic channel (as a control variable) on the electric power output, the role of the externally applied magnetic field (applied magnetic-field flux density) on the plasma streamlines, and the use of seed alkali injection to boost the electric conductivity of the expanding plasma gas may be investigated in other studies by extending the model provided in this work [110, 111, 112]. OpenFOAM might also be viewed as an educational asset [113, 114, 115], as it can be incorporated into higher education programs related to computer engineering, fluid mechanics, numerical methods, and applied mathematics.

The second goal of this work is to present comprehensive results of three-dimensional computational fluid dynamics (CFD) modeling of the channel of the Sakhalin pulsed magnetohydrodynamic generator with solid-propellant plasma (PMHDG-SPP). Unlike various reported results in the literature, the current study shows a large number of three-dimensional and sampled one-dimensional variations of fluid fields and electric fields, as well as aggregate system-level scalar values. All these results help in understanding better the complex phenomena inside the channel. CFD modeling and post-processing of its results are very beneficial in this regard, due to the digital non-intrusive probing at any spatial location of the simulated domain. Although Sakhalin is an old system, it remains an exemplary MHD study case due to the details reported about it. Therefore, this goal is viewed as a beneficial contribution to the MHD generation field, as it can guide future attempts to construct a similar system, either pulsed for geological research or sustained for electric power generation.

The third goal of this work is to provide a brief review of former solid-propellant plasma (SPP) pulsed magnetohydrodynamic generators (PMHDG).

This study contributes to regaining interest in MHD power generation, aiming for it to be further investigated as a potential way for diversifying the energy mix locally and globally [116, 117], expanding the oxy-combustion carbon capture technology, benefiting from an exceptionally high volumetric power density [118, 119, 120], utilizing concentrated direct power extraction, facilitating the process of electrification [121, 122], and pursuing unconventional energy solutions and technology transformation [123, 124] to help in achieving net-zero emissions [125, 126].

Significance of the Sakhalin PMHDG within the MHD research

The Sakhalin pulsed magnetohydrodynamic generator (PMHDG) was a significant milestone in the magnetohydrodynamic (MHD) research and application because it was a full-scale (not a lab-scale or a pilot-scale) successful demonstration of the MHD concept when utilizing seeded combustion plasma. In addition, the published data about this large power unit revealed valuable sources of information about realistic operational conditions (such as what level of magnetic-field flux density is needed) and also revealed the gigantic power density that can be achieved from a relatively compact unit [127]. The adoption of the Sakhalin PMHDG in the current work as a demonstration case is an excellent example of how this system remains useful to the MHD field to date.

Research method

This section aims to describe the mathematical, computational, and geometric settings of the proposed simulation modeling for generic Faraday-type magnetohydrodynamic (MHD) channels having continuous electrodes.

By being continuous electrically-conducting electrodes (made of metal or graphite, for example), either electrode is assigned a single voltage (a single electric potential). In this study, the anode is assigned a reference voltage of zero. Thus, the “cathode voltage” here refers to the voltage difference between the higher cathode voltage and the lower anode voltage.

Fluid flow equations

We present here the governing partial differential equations for the plasma as a homogeneous compressible turbulent gas. These equations are extended versions of the classical Favre-averaged Navier–Stokes equations (FANS), by adding supplementary terms that mathematically account for the electromagnetic effects on the electrically-conductive plasma. The Favre-averaged Navier–Stokes equations are commonly referred to as RANS (Reynolds-averaged Navier–Stokes equations), although RANS strictly applies to incompressible (constant-density) fluids, whereas the Favre-averaged Navier–Stokes equations are an extension of RANS to compressible (variable-density) fluids, which pertain to MHD generators operating on combustion plasma [128, 129, 130, 131]. The RANS formulation utilizes simple (unweighted) time averaging, whereas the FANS formulation utilizes density-weighted (mass-weighted) time averaging [132, 133, 134].

The scalar mass conservation equation (the continuity equation) of the plasma gas is identical to the equation governing ordinary gases (not electrically-conducting). The presence of a magnetic field and the existence of an electric conductivity of the plasma do not influence the mass conservation law of that plasma. Therefore, the mass conservation equation is

∂ρ∂t+∇⋅(ρu⃗)=0(1)\frac{\partial\rho}{\partial t}+\nabla\cdot(\rho\vec{u})=0 \tag*{(1)}

where ρ\rho is the mass density of the plasma gas, tt is the time, u⃗\vec{u} is the velocity vector of the plasma (this is absolute velocity, relative to a fixed laboratory frame), and ∇⋅\nabla\cdot is the divergence operator [135, 136].

The vector linear momentum conservation equation for the plasma flow within the MHD channel is an extension of the conventional linear momentum conservation equation for a non-reacting single-phase compressible turbulent flow, where a source term is added to account for the Lorentz force per unit volume, acting on the charged particles within the plasma gas as a body force exerted on a unit volume of the plasma flowing inside the MHD channel [137, 138]. To explain the cause of this source term, it should be noted that any current-passing electrically-conducting medium that is in a translational motion while subject to a magnetic field experiences an induced force called the Lorentz force, which is perpendicular to both the translational motion and the applied magnetic field [139, 140].

Therefore, the extended plasma’s linear momentum equation within the MHD channel is

∂ρu⃗∂t+∇⋅(ρu⃗⊗u⃗)+∇p−∇⋅(τ⃗v+τ⃗t)=J⃗×B⃗(2)\frac{\partial\rho\vec{u}}{\partial t}+\nabla\cdot(\rho\vec{u}\otimes\vec{u})+\nabla p-\nabla\cdot\left(\vec{\tau}_{v}+\vec{\tau}_{t}\right)=\vec{J}\times\vec{B} \tag*{(2)}

where the operator ⊗\otimes represents the outer product of two vectors, pp is the pressure (absolute pressure), ∇p\nabla p is the pressure gradient vector, τ⃗v\vec{\tau}_{v} is the viscous shear stress tensor, τ⃗⃗t\vec{\vec{\tau}}_t is the turbulent shear stress tensor, J⃗\vec{J} is the electric-current density (the current density) vector, B⃗\vec{B} is the magnetic-field flux density (the magnetic field) vector, and the right-hand side term J⃗×B⃗\vec{J} \times\vec{B} is the added source term (the Lorentz force per unit volume of plasma) [141, 142, 143, 144].

The viscous shear stress tensor τ⃗⃗v\vec{\vec{\tau}}_v is a deviatoric (traceless) tensor, modeled using the following constitutive relation [145, 146]:

τ⃗⃗v=μ(∇⃗u+[∇⃗u]T−23(∇⋅u⃗)I⃗)(3)\vec{\vec{\tau}}_v = \mu\left( \vec{\nabla}u + \left[\vec{\nabla}u\right]^T - \frac{2}{3}(\nabla\cdot\vec{u})\vec{I} \right) \tag*{(3)}

where μ\mu is the absolute viscosity (the dynamic viscosity) of the plasma gas, ∇⃗u\vec{\nabla}u is a tensor representing the gradient of the velocity vector, [∇⃗u]T\left[\vec{\nabla}u\right]^T is the transpose of ∇⃗u\vec{\nabla}u, and I⃗\vec{I} is the identity tensor [147, 148].

The turbulent (or Reynolds) stress tensor τ⃗⃗t\vec{\vec{\tau}}_t is modeled using the following gradient transport hypothesis (eddy-viscosity turbulence modeling) [149]:

τ⃗⃗t=μt(∇⃗u+[∇⃗u]T−23(∇⋅u⃗)I⃗)−23ρkI⃗(4)\vec{\vec{\tau}}_t = \mu_t \left( \vec{\nabla}u + \left[\vec{\nabla}u\right]^T - \frac{2}{3}(\nabla\cdot\vec{u})\vec{I} \right) - \frac{2}{3}\rho k\vec{I} \tag*{(4)}

where μt\mu_t is the turbulent viscosity, kk is the turbulent kinetic energy per unit mass, and the spherical tensor −23ρkI⃗-\frac{2}{3}\rho k\vec{I} appears due to the eddy-viscosity turbulence modeling [150, 151].

The sum of the laminar viscosity (the molecular viscosity) and the turbulent viscosity (the eddy viscosity) is the effective viscosity (μeff\mu_{eff}). [152, 153]

μeff=μ+μt(5)\mu_{eff} = \mu+ \mu_t \tag*{(5)}

Therefore, the sum of the viscous stress tensor and the turbulent stress tensor can be expressed as [154, 155]

τ⃗⃗v+τ⃗⃗t=μeff(∇⃗u+[∇⃗u]T−23(∇⋅u⃗)I⃗)−23ρkI⃗(6)\vec{\vec{\tau}}_v + \vec{\vec{\tau}}_t = \mu_{eff} \left( \vec{\nabla}u + \left[\vec{\nabla}u\right]^T - \frac{2}{3}(\nabla\cdot\vec{u})\vec{I} \right) - \frac{2}{3}\rho k\vec{I} \tag*{(6)}

It is worth mentioning that the tensor (∇⃗u+[∇⃗u]T−23(∇⋅u⃗)I⃗)\left( \vec{\nabla}u + \left[\vec{\nabla}u\right]^T - \frac{2}{3}(\nabla\cdot\vec{u})\vec{I} \right) is the deviatoric (traceless) component of the velocity gradient tensor ∇⃗u\vec{\nabla}u, which has a trace of 23(∇⋅u⃗)\frac{2}{3}(\nabla\cdot\vec{u}), and this trace quantity vanishes for incompressible fluids, but it is not zero here in the presented MHD plasma low model [156, 157, 158, 159].

A transport scalar partial differential equation is solved for obtaining the spatial distribution and temporal evolution of the turbulent kinetic energy per unit mass (kk), and another scalar partial differential equation is solved for obtaining the dissipation rate (ϵ\epsilon or epsilon) [160, 161].

The scalar equation of energy conservation is written here using the total (stagnation) specific internal energy, e~\tilde{e}, as the dependent variable, instead of the temperature TT. This form is suitable for high-speed gases, as encountered in open-cycle MHD channels [162, 163, 164, 165]. As with the case of the vector momentum equation, the scalar energy equation has a source term that is not present in the ordinary form (for non-electrically-conductive gases). This source is the power (per unit volume of plasma) extracted from the plasma and converted into electric power (per unit volume of plasma) to an external electric load connected to the electrodes of the MHD channel.

Thus, the extended energy equation for the plasma gas is

∂ρe~∂t+∇⋅(ρu⃗e~)+∇⋅(κeff∇T)+∇⋅(u⃗⋅τ⃗⃗)=J⃗⋅E⃗L(7)\frac{\partial\rho\widetilde{e}}{\partial t}+\nabla\cdot\left(\rho\vec{u}\widetilde{e}\right)+\nabla\cdot\left(\kappa_{eff}\nabla T\right)+\nabla\cdot\left(\vec{u}\cdot\vec{\vec{\tau}}\right)=\vec{J}\cdot\vec{E}_{L} \tag*{(7)}

where κeff\kappa_{eff} is the effective thermal conductivity (accounting for both laminar/molecular effect and turbulent/eddy effect in heat conduction), −κeff∇T-\kappa_{eff}\nabla T is the effective diffusion heat flux vector (expressed in terms of the temperature gradient ∇T\nabla T according to Fourier’s law), ∇⋅(u⃗⋅τ⃗⃗)\nabla\cdot\left(\vec{u}\cdot\vec{\vec{\tau}}\right) is the viscous-stresses power (rate of work by the plasma) per unit plasma volume due to viscous stresses, and J⃗⋅E⃗L\vec{J}\cdot\vec{E}_{L} is the source term due to the electric properties of the plasma [166, 167]. The vector E⃗L\vec{E}_{L} is the electrostatic field (caused by the voltage difference between the MHD electrodes due to the externally applied load “if applicable” or due to the external electric circuit being open “the electrodes are not electrically connected electrically”). The vector field E⃗L\vec{E}_{L} is an applied electric field on the plasma due to the voltage difference at the electrodes surrounding it, and these electrodes (grounded anode and positive cathode) are used to power an external electric load, thus we also refer to this electric field as the electrostatic field. The vector field E⃗L\vec{E}_{L} is not directly dependent on the motion of the plasma, which explains the name “electrostatic”. The vector field E⃗L\vec{E}_{L} can even be externally applied and ma manually controlled, by connecting the electrodes of the MHD channel to a DC power source (instead of an electric load). On the other hand; another electric field is induced due to the translational motion of the electric-conductive plasma gas with a velocity vector u⃗\vec{u} within an applied magnetic magnetic-field flux density B⃗\vec{B}; this induced electric field is u⃗×B⃗\vec{u}\times\vec{B}, and it can be referred to as an “electrodynamic” field. The load electric field E⃗L\vec{E}_{L} is irrotational (as per Coulomb’s law) [168, 169]. This means

∇×E⃗L=0(8)\nabla\times\vec{E}_{L}=0 \tag*{(8)}

The source term J⃗⋅E⃗L\vec{J}\cdot\vec{E}_{L} actually has a negative value (the electrostatic field vector is directed against the electric-current density vector), making this source term act actually as an energy sink, which is the valid interpretation of it as an expression of the process of extracting energy from the plasma flow and supplying it as electric energy to an external electric load. In the idealized (most simplified) case of one-dimensional (unidirectional) constant plasma velocity through a constant-cross section MHD channel, one-dimensional (unidirectional) constant applied magnetic field and one-dimensional (unidirectional) constant electrostatic field being perpendicular to the parallel electrodes (from the grounded anode to the positive cathode), and with the three fields are mutually orthogonal to each other; this energy source term reduces to −JEL-J E_L. Thus, it is actually an energy sink term with a magnitude of ∣JEL∣\lvert J E_L\rvert, where JJ and ELE_L reduce to scalar values (but the current density JJ is from the anode to the cathode, while the electrostatic field ELE_L is from the cathode to the anode) [170].

The total specific internal energy e~\widetilde{e} is the sum of the static specific internal energy ee and the specific kinetic energy 0.5 u⃗⋅u⃗0.5\,\vec{u}\cdot\vec{u}. Mathematically, this is expressed as [171]

e~=e+12u⃗⋅u⃗(9)\tilde{e}=e+\frac{1}{2}\vec{u}\cdot\vec{u} \tag*{(9)}

The static specific internal energy ee is related to the static specific enthalpy hh as [172, 173]

h=e+pρ(10)h=e+\frac{p}{\rho} \tag*{(10)}

Likewise, the total specific internal energy e~\tilde{e} is related to the total specific enthalpy h~\tilde{h} as [174, 175]

h~=e~+pρ(11)\tilde{h}=\tilde{e}+\frac{p}{\rho} \tag*{(11)}

This means

h~=h+12u⃗⋅u⃗(12)\tilde{h}=h+\frac{1}{2}\vec{u}\cdot\vec{u} \tag*{(12)}

The ideal gas law (ideal gas equation of state) is also needed in the MHD model, as an algebraic relation between the absolute pressure pp, absolute temperature TT, and density ρ\rho. The ideal gas law is not affected by the electric characteristics of the weakly-ionized seeded combustion plasma, which is still treated as a gas thermodynamically. The ideal gas law has the form [176, 177, 178]

p=ρRT(13)p=\rho R T \tag*{(13)}

where RR is the specific gas constant for the plasma gas, which is related to the universal (molar) gas constant R‾\overline{R} and the plasma molecular weight WW as [179]

R=R‾W(14)R=\frac{\overline{R}}{W} \tag*{(14)}

The value of R‾\overline{R} is 8.314 J/(mol.K) or 8,314 J/(kmol.K) [180]. If the plasma is treated as a mixture of two or more gaseous species, then the molecular weight WW depends on the local chemical composition of the plasma (at a given computational cell) as [181, 182]

W=∑iNXiWi(15)W=\sum_{i}^{N}X_iW_i \tag*{(15)}

where XiX_i is the mole fraction of the iith gaseous species in the plasma gas mixture (such as carbon dioxide, CO2_2; or water vapor, H2_2O), WiW_i is the molecular weight of that iith gaseous species, and NN is the number of gaseous species in the plasma gas mixture.

Electric fields equations

In the previous subsection, it was shown that three electromagnetic vector fields are needed in order to integrate the system of partial differential equations governing the density, velocity, and the total specific internal energy of the plasma flow within the MHD channel. These three electromagnetic vector fields appear in the two source terms that arise in the extended vector momentum equation and the extended scalar energy equation. These three needed electromagnetic vector fields are (1) the electric-current density vector (or simply the current density) J⃗\vec{J}, (2) the magnetic-field flux density vector (or simply the magnetic field) B⃗\vec{B}, (3) and the electrostatic vector field E⃗L\vec{E}_L.

The magnetic-field flux density B⃗\vec{B} is a specified applied field. Thus, in the proposed MHD model here, only the current density field J⃗\vec{J} and the electrostatic field E⃗L\vec{E}_L need to be estimated.

The approach proposed here for handling the electric aspect of the problem utilizes a scalar electric potential ϕ\phi field as a working variable that is directly solved for, and then its solution is used to indirectly compute the fields J⃗\vec{J} and E⃗L\vec{E}_L.

The electric potential scalar field ϕ\phi is related to the electrostatic vector field E⃗L\vec{E}_L as follows:

E⃗L=−∇ϕ(16)\vec{E}_L=-\nabla\phi \tag*{(16)}

Thus, the gradient of the electric potential is the electrostatic field, but in the opposite direction. The above mathematical relation is made possible given that the electrostatic field E⃗L\vec{E}_L is irrotational [183, 184, 185, 186].

The electric potential ϕ\phi is governed by a Poisson-type parabolic partial differential equation as [187, 188]

∇⋅(σ⃗eff⋅∇ϕ)=∇⋅(σ⃗eff⋅(u⃗×B⃗))(17)\nabla\cdot\left(\vec{\sigma}_{eff}\cdot\nabla\phi\right)=\nabla\cdot\left(\vec{\sigma}_{eff}\cdot\left(\vec{u}\times\vec{B}\right)\right) \tag*{(17)}

where σ⃗eff\vec{\sigma}_{eff} is an effective electric conductivity tensor for the plasma gas. For the case of unidirectional magnetic-field flux density in the ZZ direction only (thus, B⃗≡[0,0,B]\vec{B}\equiv[0,0,B]), with BB being the magnitude of that magnetic-field flux density (which can be a function of space rather than being a uniform constant), the effective electric conductivity tensor has the following form:

σ⃗eff=σ[1−ββ2+10ββ2+110001](18)\vec{\sigma}_{eff}=\sigma\begin{bmatrix}1 & -\frac{\beta}{\beta^{2}+1} & 0 \\ \frac{\beta}{\beta^{2}+1} & 1 & 0 \\ 0 & 0 & 1\end{bmatrix} \tag*{(18)}

where σ\sigma is the scalar electric conductivity of the plasma, and β\beta is the dimensionless Hall parameter (electron’s Hall parameter), which is the product of the electron mobility μe\mu_e and the magnitude of the applied magnetic field BB [189, 190, 191]. Therefore,

β=μeB(19)\beta=\mu_e B \tag*{(19)}

The effective electric conductivity tensor is used to express the generalized form (the vector form) of Ohm’s law for the electrically-conductive plasma, as [192, 193]

J⃗=σ⃗eff⋅(E⃗L+u⃗×B⃗)(20)\vec{J}=\vec{\sigma}_{eff}\cdot\left(\vec{E}_L+\vec{u}\times\vec{B}\right) \tag*{(20)}

It should be noted that the vector E⃗L+u⃗×B⃗\vec{E}_L+\vec{u}\times\vec{B} is the net electric field acting internally on the plasma (as an electrically-conductive medium having its own internal electric resistivity), and it accounts for both the electrostatic field E⃗L\vec{E}_L and the electrodynamic field u⃗×B⃗\vec{u}\times\vec{B}. As an illustrative analogy with a simple battery-lamp circuit, the field u⃗×B⃗\vec{u}\times\vec{B} is likened to the battery voltage, the field E⃗L\vec{E}_L is likened to the voltage drop across the lamp, and the field E⃗L+u⃗×B⃗\vec{E}_L+\vec{u}\times\vec{B} is likened to the voltage drop across the battery itself due to its internal electric resistance. Furthermore, the absolute value of the energy equation source term ∣J⃗⋅E⃗L∣\left|\vec{J}\cdot\vec{E}_L\right| can be likened to the power dissipated in the lamp. In the plasma’s energy equation, this term has a negative value because, for the plasma, it is power extracted (removed).

It should also be noted that the proposed solution method for the electric fields assumes that the magnetic-field flux density BB is fixed in time (but it does not need to be fixed in space), and thus the magnetic-field flux density BB is not affected by the plasma flow. This corresponds to the low magnetic Reynolds number approximation [194, 195]. The magnetic Reynolds number (Rem\mathrm{Re}_m) is a dimensionless quantity that helps in quantifying the interaction between the moving plasma and the magnetic field [196, 197]. Under large magnetic Reynolds numbers (Rem≫1\mathrm{Re}_m \gg1), the magnetic field lines can be likened to elastic bands that are frozen into the electrically-conductive plasma [198]. The velocity of the plasma establishes a secondary induced magnetic-field flux density b⃗\vec{b}, which is added to the applied magnetic-field flux density B⃗\vec{B}, making the total magnetic-field flux density actually dependent on the plasma flow. This additional flow-dependent magnetic-field flux density then affects the plasma velocity through the source term in the plasma momentum equation, presented in Eq. (2). Thus, at high magnetic Reynolds numbers, a two-way coupling exists between the magnetic-field flux density seen by the traveling plasma and the velocity field of that plasma. On the other hand, under small magnetic Reynolds numbers (Rem≪1\mathrm{Re}_m \ll1), the movement of the plasma has a negligible effect on the magnetic-field flux density acting on it. Therefore, it is reasonable in that case to treat the magnetic-field flux density acting upon the plasma as the fixed externally-applied B⃗\vec{B} field only. This means that the low magnetic Reynolds number approximation treats the coupling between the magnetic-field flux density and the plasma motion as having a one-way direction, with the externally-applied magnetic-field flux density affecting the motion of the plasma while the induced current density within the moving plasma does not distort the magnetic field through producing an additional induced one [199]. The low magnetic Reynolds number (low-Rem\mathrm{Re}_m) approximation is also called an “inductionless” approximation [200]. On the other hand, when the induced magnetic-field flux density is accounted for, this corresponds to a “self-excitation” or “self-excited” system [201].

Mathematically, the magnetic Reynolds number (Rem\mathrm{Re}_m) is defined as

Rem=μm∗σ∗u∗L∗(21)\mathrm{Re}_m=\mu_m^*\sigma^*u^*L^* \tag*{(21)}

where μm∗\mu_m^* is a reference magnetic permeability. The magnetic permeability of vacuum (the permeability of free space or the magnetic constant) μ0\mu_0 is a universal constant with the exact value of 4π×10−7 H/m4\pi\times10^{-7}\ \mathrm{H}/\mathrm{m} [202, 203, 204]. In the above equation defining Rem\mathrm{Re}_m, σ∗\sigma^* is a reference electric conductivity of the electrically-conductive medium, u∗u^* is a reference scalar speed for the electrically-conductive medium, and L∗L^* is a reference length relevant to the geometric scales of the problem.

The definition of the magnetic Reynolds number (Rem\mathrm{Re}_m) in Eq. (21) can be reformulated as

Rem=u∗L∗μm∗σ∗(22)Re_m = \frac{u^* L^*}{\mu_m^* \sigma^*} \tag*{(22)}

where the product μm∗σ∗\mu_m^* \sigma^* has the dimension of (area/time), which is the same as the momentum diffusivity (the kinematic viscosity) for fluids. Therefore, the quantity μm∗\mu_m^* may be called a reference “magnetic diffusivity”, and assigned the symbol νm∗\nu_m^* that resembles the symbol ν∗\nu^* used for designating a reference momentum diffusivity (a reference kinematic viscosity) in fluid mechanics [205].

Equation (22) thus can be written as

Rem=u∗L∗νm∗(23)Re_m = \frac{u^* L^*}{\nu_m^*} \tag*{(23)}

The above form is very similar to the one used for defining the conventional Reynolds number (Re) in fluid mechanics applications, which is [206, 207]

Re=u∗L∗ν∗(24)Re = \frac{u^* L^*}{\nu^*} \tag*{(24)}

This conventional Reynolds number (Re) in fluid mechanics is used as a nondimensional criterion to infer whether the fluid flow is expected to be in a laminar (regular and smooth) regime or a turbulent (irregular with a lot of mixing) regime. However, unlike the magnetic Reynolds number (RemRe_m); the threshold of regime transitioning for the conventional Reynolds number (Re) tends to be much larger than unity, and this threshold is dependent on the type of flow (for example, internal flows inside a cylindrical pipe have a lower threshold than external flows over the same cylindrical pipe).

The low magnetic Reynolds number (low-RemRe_m) approximation is relevant in MHD generators, and it is adopted in the proposed MHD model here [208, 209]. To demonstrate this relevance, we consider a representative situation of a weakly-ionized plasma gas for MHD channels, formed by seeding hot air at 3000 °C (3,273 K) with a small amount of potassium vapor (2% fraction). Under a reasonable reference length of 1 m and a reasonable reference speed of 1000 m/s, the magnetic Reynolds number (RemRe_m) is near 0.13 only, while the conventional Reynolds number (Re) is about 3.5×1063.5 \times10^6 [210].

For the Sakhalin pulsed MHD generator, the induced magnetic-field flux density b⃗\vec{b} is small compared to the external magnetic-field flux density B⃗\vec{B}, with the peak of b⃗\vec{b} (about 0.19 T) being less than 10% of the peak of B⃗\vec{B} (about 2.1 T). This induced magnetic-field flux density causes the overall magnetic-field flux density (the sum of B⃗\vec{B} and b⃗\vec{b}) to be less than the externally applied B⃗\vec{B} at the first region of the channel (nearly in its first half), but more than the externally applied B⃗\vec{B} in the second region of the channel (nearly in its second half), and the alteration due to b⃗\vec{b} are smallest near the middle of the longitudinal dimension of MHD channel (around X=2.25X = 2.25 m). The influence of the induced b⃗\vec{b} on the estimated electric power generation is only 2.5% [211]. So, our low magnetic Reynolds number (low-RemRe_m) approximation is considered suitable, despite that the magnetic Reynolds number (RemRe_m) for the Sakhalin PMHD generator is not very small compared to unity, but it is still less than one (about 0.5).

For a solid conductor, the generalized form (vector form) of Ohm’s law, as presented in Eq. (20), reduces to the classical scalar form of Ohm’s law, which is

I=V/R(25)I = V/R \tag*{(25)}

where II is the electric current, VV is the voltage difference (voltage drop across the electric load), and RR is the electric resistance of the electric load.

Using Eq. (18) in Eq. (20), and expanding the resulting expression from a vector equation into three scalar equations gives the following three Cartesian components of the electric density vector, J⃗≡[Jx,Jy,Jz]\vec{J} \equiv[J_x,J_y,J_z]:

Jx=σβ2+1[(EL,x+vB)−β(EL,y−uB)](26)J_x = \frac{\sigma}{\beta^2+1}\left[(E_{L,x}+vB)-\beta(E_{L,y}-uB)\right] \tag*{(26)}
Jy=σβ2+1[(EL,y−uB)+β(EL,x+vB)](27)J_y = \frac{\sigma}{\beta^2+1}\left[(E_{L,y}-uB)+\beta(E_{L,x}+vB)\right] \tag*{(27)}
Jz=σEL,z(28)J_z = \sigma E_{L,z} \tag*{(28)}

where uu, vv, and ww are the three Cartesian components of the plasma velocity vector u⃗\vec{u}, and EL,xE_{L,x}, EL,yE_{L,y}, and EL,zE_{L,z} are the three Cartesian components of the electrostatic vector E⃗L\vec{E}_L. Thus, u⃗≡[u,v,w]\vec{u} \equiv[u,v,w]. and E⃗L≡[EL,x,EL,y,EL,z]\vec{E}_L \equiv[E_{L,x},E_{L,y},E_{L,z}]. It can be noticed that while there is a coupling between JxJ_x and JyJ_y, they are decoupled from JzJ_z. This decoupling is a result of assuming the magnetic-field flux density B⃗\vec{B} to be unidirectional, thus B⃗≡[0,0,B]\vec{B} \equiv[0,0,B] in the proposed MHD model.

The Poisson equation, Eq. (17), for the electric potential ϕ\phi has the electric potential in the left-hand side only, which is treated with implicit discretization, while the right-hand side has the flow velocity, which is discretized explicitly.

When the electric potential ϕ\phi is obtained by integrating the Poisson equation, Eq. (17), numerically, a Dirichlet boundary condition (a first-type boundary condition) is applied at the anode (the top MHD boundary), by enforcing the value of ϕ\phi to be zero, which is an arbitrary value that represents electric grounding [212, 213, 214]. Another Dirichlet boundary condition is applied at the positive cathode electrode (the bottom MHD boundary), by enforcing the value of ϕ\phi there to be equal to the aimed value for the MHD operation (the target voltage drop needed for powering the external electric load, or the target open-circuit voltage if no load is connected). Therefore, the two boundary conditions for the electric potential ϕ\phi at the two electrodes are

ϕanode=0(29)\phi_{anode} = 0 \tag*{(29)}
ϕcathode=ΔVL(30)\phi_{cathode} = \Delta V_L \tag*{(30)}

where ΔVL\Delta V_L is the target voltage difference across the electrodes and thus across the externally connected load (or the open-circuit voltage).

For the two other boundaries of the MHD channel (the non-electrically-conductive walls), a Neumann boundary condition (a second-type boundary condition) is applied, which has the form [215, 216, 217]

∂ϕ∂n(or ∇ϕ⋅n^)=(u⃗×B⃗)boundary⋅n^(31)\frac{\partial\phi}{\partial n}\left(\text{or }\nabla\phi\cdot\hat{n}\right)=\left(\vec{u}\times\vec{B}\right)_{\mathrm{boundary}}\cdot\hat{n} \tag*{(31)}

where n^\hat{n} is a unit normal vector pointing perpendicularly away from the MHD boundary wall (as if leaving the channel laterally).

After obtaining the electric potential field ϕ\phi, the electrostatic field E⃗L\vec{E}_L is computed as the negative gradient of ϕ\phi using Eq. (32), which is repeated below for a convenient flow of the analysis.

E⃗L=−∇ϕ(32)\vec{E}_L=-\nabla\phi \tag*{(32)}

Finally, the generalized Ohm’s law is used to compute the electric-current density J⃗\vec{J} according to Eq. (33), which is repeated below for a convenient flow of the analysis.

J⃗=σ⃗eff⋅(E⃗L+u⃗×B⃗)(33)\vec{J}=\vec{\sigma}_{eff}\cdot\left(\vec{E}_L+\vec{u}\times\vec{B}\right) \tag*{(33)}

Geometry and mesh of the Sakhalin MHD channel

The geometry and operational settings for the modeled Sakhalin MHD channel are illustrated in Figure 1. The bulk flow direction of the supersonic plasma is along the XX-axis. The unidirectional magnetic field depends only on the axial distance (XX) from the channel inlet, and the range of XX is from 0 to 4.5 m. The anode is the upper surface of the channel (having positive linearly-increasing YY coordinates), while the cathode is the lower surface of the channel (having negative linearly-decreasing YY coordinates). The width of the channel (along the ZZ direction) is constant, with a value of 1 m. The height (along the YY direction) of the channel increases from 0.9 m at the inlet to 1.6 m at the outlet.

Three-dimensional illustration of the modeled Sakhalin MHD channel

Figure 1. Three-dimensional illustration of the modeled Sakhalin MHD channel

Projected views (front view and top view) of the MHD channel are provided in Figure 2. The front view is a trapezium (a trapezoid), while the top view is a rectangle.

Image not extracted

Figure 2. Projection views of the modeled Sakhalin MHD channel

The spatial discretization of the Sakhalin MHD channel is illustrated in Figure 3. Due to its geometric simplicity, the channel is discretized spatially as a single block, with a total of 376,380 hex cells (hexahedral computational cells). We used 180 cells along the axial XX dimension (the length), 51 cells along the vertical YY dimension (the height), and 41 cells along the lateral ZZ dimension (the width). Hexahedral (structured) meshes tend to be favored over tetrahedral (unstructured) meshes due to the higher accuracy and the ability to have a larger aspect ratio [218, 219, 220]. Similarly, in two-dimensional problems, quadrilateral cells are computationally preferred over triangular cells [221, 222]. Therefore, when possible, a tetrahedral mesh may be limited to complex geometries that

Image not extracted

Figure 3. Zoomed views of the discretization mesh of the Sakhalin MHD channel

cannot be represented well through hexahedral mesh elements. In our CFD simulation of the Sakhalin MHD channel, tetrahedral cells were not necessary.

Our selected spatial discretization makes each cell nearly a cube (cells have a comparable size of their edges, near 0.025 m), and this rough regularity in the mesh is preferred in CFD simulations compared to highly skewed or stretched cells [223, 224].

Furthermore, our selection of an odd number of cells for the height (51 cells) and the width (41 cells) ensures that the longitudinal centerline of the channel coincides with a sequence of cell centers, which are also equally spaced. This is helpful because we sample the simulation results along that longitudinal centerline, which starts from the [X,Y,Z][X,Y,Z] coordinates [0,0,0][0,0,0] and ends at the point [4.5,0,0][4.5,0,0]. Thus, exact cell-center values are readily available for sampling, without approximating interpolation.

Empirical expressions for Sakhalin

The previous mathematical description of the governing equations and computational modeling for the MHD plasma is not restricted to the Sakhalin pulsed magnetohydrodynamic generator (PMHDG). However, a number of thermofluidic and electromagnetic properties appear in these governing equations, which should be modeled in the computational fluid dynamics (CFD) simulations using customized submodels [225, 226, 227]. Such properties include the specific heat capacity at constant pressure CpC_p, the magnitude of the unidirectional magnetic-field flux density BB the Hall parameter β\beta, and the scalar electric conductivity σ\sigma.

The Sakhalin PMHDG has empirical expressions published in the literature that describe the aforementioned four quantities [228]. Such expressions are listed in Table 2. It should be noted that they correspond to the Pamir-3U SPP-PMHDG. No expressions for Sakhalin itself were available. However, because such data were published. Due to the similarity in the operation between Pamir-3U and Sakhalin (but Sakhalin has a much larger power capacity), these expressions were assumed to be valid also for Sakhalin. In addition, the same table lists other operational conditions used in our simulation based on published data in the literature.

QuantityUnitExpression or valueRemarks
Specific heat capacity at constant pressure, CpC_pJ/(kg.K)CpT=649.863+0.620932TC_pT = 649.863 + 0.620932TCpC_p increases linearly with the temperature<br>TT is in kelvins (absolute temperature)
Magnetic-field flux density magnitude, BBT (tesla)B(X)=∑i=07aiXiB(X)=\sum_{i=0}^{7}a_iX^i<br>a0=1.59103012,a_0=1.59103012,<br>a1=1.62627541,a_1=1.62627541,<br>a2=−2.41601024,a_2=-2.41601024,<br>a3=1.81448629,a_3=1.81448629,<br>a4=−0.777421291,a_4=-0.777421291, a5=0.188450611,a_5=0.188450611,<br>a6=−0.0230846554,a_6=-0.0230846554,<br>a7=0.00104129100a_7=0.00104129100Our seventh-degree polynomial fit of a published curve<br>XX is the axial distance (in meters) from the inlet of the MHD channel<br>XX starts from 0 at the MHD channel inlet<br>XX reaches 4.5 m at the MHD channel outlet
Hall parameter, β\beta–β(B,p~,T)=Bb0+b1Tp~\beta(B,\tilde{p},T)=B\frac{b_0+b_1\sqrt{T}}{\tilde{p}}<br>b0=0.393664,b_0=0.393664,<br>b1=0.00302522b_1=0.00302522BB is in teslas<br>TT is in kelvins (absolute temperature)<br>p~\tilde{p} is the absolute pressure expressed in standard atmospheres (atm = 101,325 Pa)
Scalar electric conductivity, σ\sigmaS/m (siemens per meter)σ(p~,T)=c0exp⁡(c1+c2Tp~+c3+c4T+(c5+c6T)p~)\sigma(\tilde{p},T)=c_0\exp\left(\frac{c_1+c_2T}{\tilde{p}}+c_3+c_4T+(c_5+c_6T)\tilde{p}\right)<br>c0=1.15184,c_0=1.15184,<br>c1=−3.29702,c_1=-3.29702,<br>c2=0.00140816,c_2=0.00140816,<br>c3=−2.02024,c_3=-2.02024,<br>c4=0.00212241,c_4=0.00212241,<br>c5=−0.156856,c_5=-0.156856,<br>c6=0.0000319339c_6=0.0000319339TT is in kelvins (absolute temperature)<br>p~\tilde{p} is the absolute pressure expressed in standard atmospheres (atm = 101,325 Pa)
Cathode voltage, ϕcathode\phi_{\mathrm{cathode}}V (volt)2,550The anode voltage is ϕanode=0\phi_{\mathrm{anode}}=0<br>This value corresponds to the experimental “run number 1” of the MHD channel
Plasma molecular weight, WWkg/kmol22.905WW is assumed to be uniform
Plasma specific gas constant, RRJ/(kg.K)362.978R=8,314/WR=8,314/W
Inlet temperature, TinT_{\mathrm{in}}K (kelvin)2,7502750 K = 2,77 °C
Inlet pressure, pinp_{\mathrm{in}}bar3.283.28 bar = 328,000 Pa = 3.2371 atm
Inlet axial velocity, uinu_{\mathrm{in}}m/s20502050 m/s = 7380 km/h
Inlet specific heat capacity at constant pressure, Cp,inC_{p,\mathrm{in}}J/(kg.K)2357.426Cp,in=Cp(T=Tin)C_{p,\mathrm{in}}=C_p(T=T_{\mathrm{in}})
Inlet specific heat capacity at constant volume, Cv,inC_{v,\mathrm{in}}J/(kg.K)1994.448Cv,in=Cp,in−RC_{v,\mathrm{in}}=C_{p,\mathrm{in}}-R (ideal gas [232])
Inlet specific heat ratio, γin\gamma_{\mathrm{in}}–1.1820γin=Cp,in/Cv,in\gamma_{\mathrm{in}}=C_{p,\mathrm{in}}/C_{v,\mathrm{in}} [233]
Inlet speed of sound, aina_{\mathrm{in}}m/s999.5ain=γinRT∗aa_{\mathrm{in}}=\sqrt{\gamma_{\mathrm{in}}RT^{*a}} (ideal gas [234])
Inlet Mach number, MinM_{\mathrm{in}}–2.05Min=uin/ainM_{\mathrm{in}}=u_{\mathrm{in}}/a_{\mathrm{in}} [235]
Inlet Plasma density, ρin\rho_{\mathrm{in}}kg/m3^30.32859ρin=pin/(RTin)\rho_{\mathrm{in}}=p_{\mathrm{in}}/(RT_{\mathrm{in}})
Inlet cross-section area, AinA_{\mathrm{in}}m2^20.9Width = 1 m, height 0.9 m
Mass flow rate, m˙\dot{m}kg/s606.2m˙=uinρinAin\dot{m}=u_{\mathrm{in}}\rho_{\mathrm{in}}A_{\mathrm{in}} [236]
Outlet cross-sectional area, AoutA_{\mathrm{out}}m2^21.6Width = 1 m, height 1.6 m

Table 2. Empirical expressions and operating conditions for Sakhalin plasma

For the magnitude of the magnetic-field flux density BB, the expression listed in the table is our seventh-degree polynomial fitting, which we obtained using the (curve_fit) function of the (optimize) package for optimization and root finding, provided with the (SciPy) open-source Python library [229, 230, 231]. The function (curve_fit) utilizes a nonlinear least squares method. Our proposed fitting function is visualized in Figure 4.

Nonlinear polynomial fitting for the magnetic-field flux density of the Sakhalin MHD channel

Figure 4. Nonlinear polynomial fitting (seventh-degree polynomial) for the magnitude of the magnetic-field flux density (BB) of the Sakhalin MHD channel, as a function of the axial distance (XX). The unidirectional magnetic field is in the ZZ direction, and is expressed in teslas (TT).

Computational Settings and Demands

As with other computational fluid dynamics (CFD) simulations, a number of choices need to be made with regard to discretization schemes and/or numerical parameters. In this subsection, we cover this aspect of the OpenFOAM model presented here for magnetohydrodynamics (MHD) channels by listing some configuration settings adopted in the simulation in Table 3.

ConditionAdopted setting
Turbulence modelStandard k-epsilon [237, 238]
Flow solverDensity-based, nearly explicit
Upwind schemeKurganov central [239, 240, 241, 242]
Prandtl number (PrPr)0.72 [243, 244]
Time-step5×10−65 \times10^{-6} s (5 μs)
Completed time steps8000
Simulated time0.04 s
Convergence tolerance10−1010^{-10}

Table 3. Some simulation conditions for the CFD simulation of the Sakhalin mhd channel

The simulated time of 0.04 s was selected because the solution reached a quasi-steady state, with negligible transience. Although the governing equations are unsteady, the simulation solution reached a stable stage.

The density (ρ\rho) and the conservative form of the velocity vector (ρu⃗\rho\vec{u}) are resolved using a diagonal solver (thus, solved explicitly) [245, 246]. The total specific internal energy (e~\tilde{e}) is resolved using a Gauss Seidel Smoother [247]. The turbulent kinetic energy per unit mass (kk) and the turbulence dissipation rate (ϵ\epsilon or epsilon) are resolved using a preconditioned bi-conjugate gradient (PBiCG) solver [248], with a Diagonal-based Incomplete Lower–Upper decomposition preconditioner (DILU) [249, 250].

We used a computing machine having two processors. The type of these processors is quad-core Intel Xeon L5335 2.00 GHz. Thus, the computing machine has a total of eight computing cores. One simulation can take one full day (24 h). The simulation environment was the Linux operating system (the openSUSE distribution).

OpenFOAM Code Lines

We provide below code lines from the proposed OpenFOAM magnetohydrodynamic (MHD) solver, based on our mathematical description provided earlier.

For example, the first part of these code lines shows how the Poisson equation, Eq. (17), for the electric potential ϕ\phi is solved using the high-level OpenFOAM programming language, through an iterative loop with (nCorr) iterations. In the code, the electric potential ϕ\phi is assigned the variable name (phi_e).

The remaining parts of the code lines show how the scalar mass conservation equation is solved, followed by the vector momentum equation, and finally the scalar energy equation [251].

for (int i = 0; i < nCorr; i++)
{
    fvScalarMatrix phiEqn
    (
        fvc::div( sigmaEff & (U ^ B) ) - fvm::laplacian(sigmaEff,phi_e)
    );
    phiEqn.relax();
    phiEqn.solve();
    E = fvc::grad(phi_e);
    J = sigmaEff & ( E + (U^B) );
    lorentzForceDensity = J ^ B;
    powerDensity = E & J;
}
solve(fvm::ddt(rho) + fvc::div(phi));
solve
(
    fvm::ddt(rho, U) - fvc::ddt(rho, U)
    - fvm::laplacian(muEff, U)
    - fvc::div(tauEffExplicit)
);
surfaceScalarField TauEffDotUDotSf
(
    (
        fvc::interpolate(muEff)*mesh.magSf()*fvc::snGrad(U)
        + (mesh.Sf() & fvc::interpolate(tauEffExplicit))
    )
    & (frac_ap*U_ifAllFluxesOut + frac_am*U_ifAllFluxesIn)
);
solve
(
    fvm::ddt(rhoE)
    + fvc::div(phiE_pU)
    - fvc::div(TauEffDotUDotSf)
    - powerDensity
);
e = rhoE/rho - 0.5*magSqr(U);
e.correctBoundaryConditions();
volScalarField kEff("kEff", thermo.Cp()*turbulence->alphaEff());
solve
(
    fvm::ddt(rho, e) - fvc::ddt(rho, e)
    - fvc::laplacian(kEff, T)
);
rhoE = rho*(e + 0.5*magSqr(U));

Limitations

Despite the broad range of physical, chemical, electromagnetic, and gas dynamic phenomena covered in the presented magnetohydrodynamic (MHD) solver for linear channels of MHD generators, a number of aspects are not captured. Although this means limitations in the solver, this does not contradict the usefulness and importance of the solver. Such limitations may be addressed by extending the solver according to the customized setting and purpose of its implementation. In a setting where the ignored details are not strongly present, the solver becomes adequate.

For example, if the fuel combustion results in a two-phase (solid particle carried by a bulk gaseous medium) with a large fraction of the solid phase that cannot be neglected, then an extension may be necessary to take into account the influence of these particles. However, fuels not featuring such behavior do not require such an extension of the solver.

As another example, in the introduced MHD solver, we acknowledge that electrode erosion is overlooked. This means that the electrodes are assumed to remain intact during the MHD channel operation. This assumption is not a concern for performance analysis, since erosion becomes noticeable only after a large period of operation. Thus, ignoring its effect is not a shortcoming, but it is still a possible area of improvement.

Validation and verification

After presenting the mathematical/computational formulation of the OpenFOAM solver developed for handling continuous Faraday channels in MHD generators, this section is provided to compare some results we obtained using the solver with values previously published in the literature, and this is a validation step for our CFD solution of the Sakhalin pulsed magnetohydrodynamics generator (PMHG), through external benchmarking. In the verification step, we perform internal benchmarking by comparing the CFD solution at the nominal spatial and temporal resolutions with another CFD solution using the same solver but at finer spatial and temporal resolutions; this verifies the ability of the CFD model to converge at the nominal resolutions [252, 253].

Before presenting the validation step; we point out that due to the uncertainty in reported data of the Sakhalin PMHDG where a range for a variable is reported, rather than a single value for it (such as the mass flow rate), the discrepancy of some reported operational characteristics (such as the MHD channel inlet velocity), the time-unsteadiness nature of the actual problem, our simplification introduced in the inlet conditions, and the empirical fitting functions used in modeling some parameters; we do not aim at achieving a close quantitative agreement with the literature information [254]. Instead, we seek to obtain values of aggregate quantities that are comparable to those reported by others. We consider three key benchmarking quantities for the validation step, as summarized in Table 4. Based on the acceptable small deviation in this table, our simulation is considered valid.

QuantityOur valueBenchmarking valueRemarks
Electric power output488.1 MW476 MW [255]• While the reported peak power value is 510 MW, we compare our power value with a smaller value (93% of the peak) as an estimated mean value during the pulse. This factor is assigned based on data for the Pamir-3U PMHDG [256]
Electric current from electrodes191.4 kA200 kA [257]• Our value is the average of the cathode and the anode (area integrated normal component of the electric-current density vectors, perpendicular to the electrode)
Plasma speed at channel exit1156 m/s1306 m/s [258]• Our value is the mass-averaged axial velocity component (the XX-component of the plasma velocity vector) at the MHD channel outlet

Table 4. Validation of our simulation for the Sakhalin MHD channel

Table 5 summarizes the verification step for our CFD simulation of the Sakhalin PMHDG channel using the proposed OpenFOAM solver. In this step, we generated an internal benchmarking solution using the same proposed OpenFOAM solver but at a finer spatial resolution and a finer temporal resolution. This auxiliary fine-resolution solution acts as a higher-fidelity reference to assess the nominal (the solution obtained with the nominal resolutions). Based on the observed small changes in the compared characteristic of the MHD channel, as shown in the table, our verification step is considered successful, and our nominal OpenFOAM CFD solution is considered satisfactorily resolution-independent. All the remaining results in this study correspond to the nominal resolutions (which are 376,380 cells and 5×10−65 \times10^{-6} s time-step).

QuantityNominal resolutionFiner resolution
Number of cells376,3801,235,250
Time step5×10−65 \times10^{-6} s2.5×10−62.5 \times10^{-6} s
Electric power output488.1 MW480.3 MW
Volume-average pressure3.128 bar3.011 bar
Volume-average Lorentz force density vector[−89.12,28.83,0][-89.12, 28.83, 0] kN/m3^3[−85.86,28.75,0][-85.86, 28.75, 0] kN/m3^3
Volume-average electric-current density vector[1.462,−4.517,0][1.462, -4.517, 0] A/cm2^2[1.457,−4.351,0][1.457, -4.351, 0] A/cm2^2

Table 5. Verification of our simulation for the Sakhalin MHD channel (resolution sensitivity analysis)

The above verification table also has indications about the validity of our OpenFOAM model, through the correct sign of the YY-component of the volumetric Lorentz force density (force per unit volume), which is pointing from the lower cathode to the upper anode for our case where the plasma’s bulk motion is in the positive XX direction, and the magnetic-field flux density is unidirectional in the positive ZZ direction. The Lorentz force vector F⃗\vec{F} on a general electrically charged particle with a positive charge qq, when this particle is carried with the plasma gas (moving at the same bulk velocity u⃗\vec{u}) is [259]

F⃗=q(E⃗L+u⃗×B⃗)(34)\vec{F}=q\left(\vec{E}_{L}+\vec{u}\times\vec{B}\right) \tag*{(34)}

Although the electrostatic field E⃗L\vec{E}_{L} reduces or alters the electrodynamic fields u⃗×B⃗\vec{u}\times\vec{B}, the resultant overall electric field E⃗L+u⃗×B⃗\vec{E}_{L}+\vec{u}\times\vec{B} is like electrodynamic fields u⃗×B⃗\vec{u}\times\vec{B} in terms of pointing vertically down (in the negative YY direction, from the upper anode to the lower cathode).

Because the effective mobile charge carriers in the plasma are the negatively-charged electrons (not the positively-charged seed ions), the charge qq is actually negative, and thus the Lorentz force actually points upward, and this is in agreement with our CFD predictions [260, 261].

The finding that the averaged electric-current density vector is pointing opposite to the averaged Lorentz force vector is also a favorable indication that the CFD model is able to predict correct vector fields. While the collected conventional electric current flows externally through the electric load from the positive cathode to the grounded anode, the electron electric current flows externally in the opposite direction from the grounded anode to the positive cathode. In the presented OpenFOAM model, the electric-current density refers to the conventional electric current. Therefore, its averaged direction within the MHD channel should be pointing down (thus, having a negative YY-component), which is correctly predicted in our simulation.

Finally, the obtained zero ZZ-component of either the averaged Lorentz force density vector or the averaged electric-current density vector is a logical outcome, given the unidirectional ZZ-oriented nature of the applied magnetic-field flux density, and this does not cause any electric-current density or Lorentz force along the ZZ direction. There is no reason for having an averaged ZZ-component of the electrostatic field (thus, EL,z=0E_{L,z}=0).

Results

We present the results of the proposed OpenFOAM solver when applied to the Sakhalin magnetohydrodynamic (MHD) channel in the next three subsections.

In the first subsection, we present scalar aggregate quantitative values. In the second subsection, we present one-dimensional graphical profiles. In the third subsection, we present three-dimensional visualizations of selected fields in the entire MHD channel.

Scalar values at the MHD channel outlet

By post-processing our simulation results, we obtain the mass-averaged values of six key selected properties of the plasma as it exits the MHD channel. These values are summarized in Table 6.

QuantityOutlet valueInlet value
Absolute temperature (K)2,738.42,750
Absolute pressure (bar)3.2943.28
Axial velocity (m/s)1,1562,050
Mach number (-)1.1612.051
Electric conductivity (S/m)48.450
Hall parameter (-)0.25550.2715

Table 6. Computed properties of the plasma (mass-averaged) at the channel outlet, and corresponding inlet values

A generic mass-averaged quantity (say ψ\psi) at the outlet is computed through density-weighted integration of that quantity ψmass−avg\psi_{\mathrm{mass-avg}} at the outlet area, and then dividing the mass flow m˙\dot{m} leaving the channel from that outlet area. Thus,

ψmass−avg=1m˙∫outlet areaρuψ dA(35)\psi_{\mathrm{mass-avg}} = \frac{1}{\dot{m}} \int_{\mathrm{outlet\ area}} \rho u \psi\,\mathrm{d}A \tag*{(35)}

where uu is the axial component of the exiting plasma (this component is perpendicular to the outlet surface), dA\mathrm{d}A is an infinitesimal area element at the outlet (which has a total finite area of 1.6 m21.6\ \mathrm{m}^{2}).

To better demonstrate the change in the plasma flow due to the direct power extraction (DPE) process within the MHD channel, the inlet values in our OpenFOAM simulation for the same six plasma properties are also listed in the table, which helps in contrasting them with the computed outlet values.

It can be seen that one major influence of the power extraction process from the plasma is an occurring deceleration process, although supersonic flows accelerate in divergent channels (as in the case of the Sakhalin channel) [262, 263].

On the other hand, the temperature and the pressure nearly did not change from their inlet values. This means that the main source of the electricity extracted from the flowing plasma is its kinetic energy, rather than its internal energy (thermal energy) or its pressure energy (flow energy).

Due to the weak change in the pressure and temperature, and because the electric conductivity and the Hall parameter are fitted as dependent functions of these two thermodynamic properties (the Hall parameter depends additionally on the magnitude of the applied magnetic-field flux density), the electric conductivity and the Hall parameter of the plasma do not change largely when the outlet location is compared with the inlet location.

Because the Mach number depends largely on the axial velocity of the plasma, and because the speed of sound is dependent on the temperature which does not show a large change between the inlet and the outlet locations of the MHD channel; the Mach number decreases strongly between the inlet and the outlet locations, similar to the change in the axial plasma velocity. This decrease of a supersonic Mach number for a flow within a divergent channel or nozzle also emphasizes the loss of kinetic energy from the plasma, which is actually decelerated within the channel because of the electric power extraction.

Centerline profiles

Through one-dimensional sampling along the centerline of the MHD channel (thus, along all XX values from 0 to 4.5 m, but with Y=0Y = 0 and Z=0Z = 0), the variations of ten thermodynamic, fluidic, or electric properties of the simulated Sakhalin channel are illustrated in the current subsection. None of the investigated profiles has a discontinuity (abrupt change), which is an implicit indication of the lack of internal instabilities in the performed simulation, which agrees with the expectation for this problem and supports the correctness of the presented model.

We start with the electric conductivity σ\sigma, and display its centerline variation in Figure 5. We point out here that this plasma electric variable is described through an empirical nonlinear regression model as a function of the local temperature and the local pressure. Therefore, its variation reflects variation in either of these two independent variables. Despite the apparent non-uniformity of the electric conductivity, its variation is smooth and bounded within a narrow range of about 4 S/m only (from 48.6 S/m to 52.8 S/m).

Centerline profile of the electric conductivity along the simulated Sakhalin MHD channel

Figure 5. Centerline profile of the electric conductivity along the simulated Sakhalin MHD channel

Next, we display the variations of the Hall parameter β\beta along the centerline of the MHD channel in Figure 6. Like the electric conductivity, the Hall parameter is described through an empirical nonlinear regression model as a function of the local temperature and the local pressure. In addition, the Hall parameter depends linearly on the magnitude of the applied magnetic-field flux density BB. The magnitude of the applied magnetic-field flux density declines rapidly near the inlet and outlet of the MHD channel, and this is clearly shown in the profile of the Hall parameter. In the internal region of the channel, the Hall parameter qualitatively follows a similar profile to that of the unidirectional applied magnetic-field flux density, which can be explained by the weak influence of the temperature and the pressure because they do not change significantly within the MHD channel. The maximum encountered value of the Hall parameter is 0.39, while the lowest value is at the MHD outlet, and it is 0.26.

Centerline profile of the Hall parameter along the simulated Sakhalin MHD channel

Figure 6. Centerline profile of the Hall parameter along the simulated Sakhalin MHD channel

Figure 7 shows the centerline profile of the Mach number, which declines in a nearly monotonic pattern, leaving the MHD channel at a noticeably smaller value of 1.26 than its inlet value of 2.05. However, the plasma remains supersonic even at the outlet (the exit Mach number is still above unity). Therefore, the existing plasma still has a lot of kinetic energy that can be exploited in a subsequent energy conversion system.

Centerline profile of the Mach number along the simulated Sakhalin MHD channel

Figure 7. Centerline profile of the Mach number along the simulated Sakhalin MHD channel

Figure 8 shows the centerline profile of the absolute pressure, which manifests slow variations within 0.6 bar. The leaving plasma still has a high pressure close to the inlet pressure (in addition to the still-high speed), thus it is subject to further energy extraction through another energy system (such as gas turbines) after deceleration to proper subsonic speeds using supersonic diffusers [235, 264].

Centerline profile of the absolute pressure along the simulated Sakhalin MHD channel

Figure 8. Centerline profile of the absolute pressure along the simulated Sakhalin MHD channel

Figure 9 and Figure 10 show the centerline profiles of the plasma density and the plasma absolute temperature, respectively. It is interesting that the temperature is practically constant near its inlet value of 2,750 K. Following the ideal gas law, the density in such a case (a nearly isothermal process) becomes essentially a scaled version of the absolute pressure, which is a satisfied feature that can be confirmed by comparing the previous Figure 10 profile of the absolute pressure with the profile of the density. The high temperature of the leaving plasma indicates an enormous amount of thermal energy that can be transferred through a heat exchanger to another fluid, for example, to generate steam that can be used in a steam power cycle. Using the empirical formula for the specific heat capacity at constant pressure for the plasma of the Sakhalin PMHDG, namely.

Centerline profile of the plasma density along the simulated Sakhalin MHD channel

Figure 9. Centerline profile of the plasma density along the simulated Sakhalin MHD channel

Centerline profile of the absolute temperature along the simulated Sakhalin MHD channel

Figure 10. Centerline profile of the absolute temperature along the simulated Sakhalin MHD channel

CpC_p (T [K]) [J/ (kg.K)] = 649.863 + 0.620932TT, the change in the specific enthalpy, designated by.

Δh≡h2−h1\Delta h \equiv h_2 - h_1, between two states (a lower-temperature state 1 and a higher-temperature state 2) can be obtained by integrating this CpC_p expression as

Δh≡h2−h1=∫T1T2Cp(T) dT(36)\Delta h \equiv h_2 - h_1 = \int_{T_1}^{T_2} C_p(T)\,dT \tag*{(36)}

This gives

Δh=649.863(T2−T1)+0.310466(T22−T12)(37)\Delta h = 649.863\left(T_2-T_1\right)+0.310466\left(T_2^2-T_1^2\right) \tag*{(37)}

If the higher-temperature state has T2=2,750T_2 = 2{,}750 K (nearly the plasma exit temperature), and the lower-temperature state has T1=300T_1 = 300 K (nearly the ambient temperature), then the enthalpic energy available per kg of plasma is 3.912×1063.912 \times10^6 J/kg (3.912 MJ/kg). This is more than enough to generate superheated steam at extremely high temperatures (even exceeding 700 °C), which is suitable to operate steam power plants [265, 266].

Figures 11 and 12 show the centerline profiles of the axial and upward velocity components of the plasma, respectively. As was the case for the Mach number, the centerline axial velocity declines as the plasma progresses through the MHD channel, reflecting a loss of kinetic energy that is converted into electric energy. The upward velocity component (the plasma velocity in the YY direction, being positive if the plasma is moving

Centerline profile of the axial velocity component along the simulated Sakhalin MHD channel

Figure 11. Centerline profile of the axial velocity component along the simulated Sakhalin MHD channel

Centerline profile of the upward velocity component

Figure 12. Centerline profile of the upward velocity component (the YY-component) along the simulated Sakhalin MHD channel

from the downward cathode to the upward anode) varies mildly around the zero value, bounded between −50 m/s and 30 m/s.

Figure 13 shows the centerline profile of the third velocity component of the plasma (the ZZ-component), which is along the unidirectional applied magnetic-field flux density. This component is practically zero at the centerline, reflecting perfect symmetry and balance of lateral forces. This is reasonable given the lack of gravitational effect along the ZZ direction, as well as the constant channel width along the same direction.

Centerline profile of the lateral velocity component

Figure 13. Centerline profile of the lateral velocity component (the ZZ-component) along the simulated Sakhalin MHD channel

Figure 14 shows the centerline profile of the downward component of the electric-current density. This component has negative values; thus, the conventional electric-current density is directed toward the bottom cathode (although the physical charge-carrying electrons are forced upward toward the upper anode). In the figure, the negative value of that already-negative conventional component is displayed, which is equivalent to displaying the absolute value of that negative conventional component. The displayed absolute conventional current density component increases nonlinearly until reaching a maximum value of 6.16.1 A/cm2^2 at a distance of 11 m from the MHD channel inlet; it then declines nonlinearly until reaching a zero value at the channel outlet.

Centerline profile of the downward component of the electric-current density

Figure 14. Centerline profile of the downward component of the electric-current density (from anode to cathode) along the simulated Sakhalin MHD channel

Three-dimensional distributions

In this subsection, we present three-dimensional views for eight selected fields as per the solution obtained in our simulation of the Sakhalin MHD channel. These views are instrumental in demonstrating the variation of each field in the entire channel.

Figure 15 displays the spatial distribution of the electric conductivity, which changes mildly between 43.9 S/m and 53.6 S/m. The electric conductivity declines slowly as the plasma approaches the rear end of the divergent channel. It is worth mentioning here that this electric conductivity (being near 50 S/m) is roughly ten times the electric conductivity of seawater (being approximately 5 S/m) [267]. Additionally, the estimated range of the maximum electric conductivity of Earth’s lower mantle is 3–10 S/m [268].

Image not extracted

Figure 15. Three-dimensional distribution of the electric conductivity within the simulated Sakhalin MHD channel

Figure 16 displays the spatial distribution of the Hall parameter, which changes between 0.253 and 0.424. The variations in the Hall parameter are determined by variations in the temperature, pressure, and the applied magnetic-field flux density.

Image not extracted

Figure 16. Three-dimensional distribution of the Hall parameter conductivity within the simulated Sakhalin MHD channel

Figure 17 displays the spatial distribution of the absolute pressure, which changes between 2.56 bar and 3.62 bar. A pressure recovery phenomenon is observed near the outlet, where the pressure increases back after its initial drop after entering the channel.

Image not extracted

Figure 17. Three-dimensional distribution of the absolute pressure within the simulated Sakhalin MHD channel

Figure 18 displays the spatial distribution of the axial velocity component of the plasma, which changes between 832.9 m/s and 2,089 m/s. The deceleration process is efficiently visible through this figure, with the axial velocity generally dropping as the plasma moves from the inlet toward the outlet.

Image not extracted

Figure 18. Three-dimensional distribution of the axial velocity component within the simulated Sakhalin MHD channel

Figure 19 displays the spatial distribution of the specific turbulent kinetic energy (the turbulent kinetic energy per unit mass, designated by the symbol kk), which changes between 1,803 m2/s2\mathrm{m}^2/\mathrm{s}^2 and 16,262 m2/s2\mathrm{m}^2/\mathrm{s}^2. This variable represents the intensity of the modeled turbulence in the plasma. This turbulence quantity is higher in the intermediate part of the channel compared to the inlet and the outlet.

Image not extracted

Figure 19. Three-dimensional distribution of the specific (per unit mass) turbulent kinetic energy within the simulated Sakhalin MHD channel

Figure 20 displays the spatial distribution of the turbulence dissipation or the turbulence dissipation rate (designated by the symbol ϵ\epsilon or the name “epsilon”), which changes between 2.05×105 m2/s32.05 \times10^{5}\ \mathrm{m}^2/\mathrm{s}^3 and 7.2×107 m2/s37.2 \times10^{7}\ \mathrm{m}^2/\mathrm{s}^3. This variable describes the loss of turbulent

Image not extracted

Figure 20. Three-dimensional distribution of the dissipation (epsilon) of the turbulent kinetic energy within the simulated Sakhalin MHD channel

motion that is converted into thermal internal heat due to viscous effects [269]. This turbulence quantity is higher in the intermediate part of the channel than in the inlet and outlet. This was the case for the turbulent kinetic energy per unit mass, and it is reasonable behavior that as the turbulence intensity increases, the turbulence dissipation also increases [270].

Figure 21 and Figure 22 display the spatial distribution of the axial and downward components of the electric-current density, respectively. Thus, the variables displayed in these figures are JxJ_x and −Jy-J_y, respectively. The axial component changes between −0.008-0.008 A/cm2\mathrm{cm}^{2} and 10.510.5 A/cm2\mathrm{cm}^{2}. Thus, the axial electric-current density is mostly from the channel inlet to the channel outlet. The downward component changes between −0.310-0.310 A/cm2\mathrm{cm}^{2} and 21.921.9 A/cm2\mathrm{cm}^{2}. Thus, the vertical electric-current density is mostly from the top anode to the bottom cathode.

Image not extracted

Figure 21. Three-dimensional distribution of the axial component of the electric-current within the simulated Sakhalin MHD channel

Image not extracted

Figure 22. Three-dimensional distribution of the downward component of the electric-current density within the simulated Sakhalin MHD channel

Conclusions

Concluding remarks

In the current study, we presented a mathematical and computational model for simulating linear magnetohydrodynamic (MHD) Faraday channels with continuous electrodes.

The computational fluid dynamics (CFD) computer language OpenFOAM is used to develop an MHD solver, which we applied to the Sakhalin pulsed solid-propellant plasma (SPP) power system, with a supersonic divergent channel. The proposed solver corresponds to the low magnetic Reynolds number (Rem\mathrm{Re}_{m}), and it utilizes the scalar electric potential as the working variable for handling the electric aspect of the problem.

After validation and verification, we used the solver to explore various aspects of the thermal, fluidic, and electric features of the problem. These include the pressure, temperature, density, velocity, Mach number, electric-current density, specific turbulent kinetic energy, and turbulence dissipation.

Summary of contributions

Despite earlier studies about this Sakhalin pulsed magnetohydrodynamic generator (PMHDG), we do not know of any previous work in the literature that provided the same comprehensive aspects as our study.

The following items can be considered as contributions made in this study:

  • A review of real examples of pulsed MHG generators (PMHD) was made, with emphasis on the Sakhalin model that was described with quantitative values and empirical regression models for its operational settings that help in modeling it by others. A large number of literature research articles were used in preparing this review.

  • A mathematical/computational model is proposed for simulating the three-dimensional fluid dynamic and electric fields for linear continuous-electrode MHD channels. The proposed solver was found to yield satisfactory outputs when compared to other independent studies. The ability of the solver to give resolution-independent results was verified.

  • Selected results from our CFD simulation for the Sakhalin MHD channel were presented and discussed. Using the power of CFD and data post-processing, it was possible to reveal various attributes of the channel of the Sakhalin PMHDG, such as the nearly-isothermal operation, the extraction of energy mainly from the kinetic energy of the plasma (rather than the thermal or the pressure energies), the unusual deceleration (opposite to the conventional situation) of supersonic flow despite

flowing in a divergent channel, the weak change in the electric conductivity, and the pressure recovery phenomenon.

Possible future research

The MHD solver presented here can be expanded in subsequent studies to make it even more useful as a generic tool for designing MHD channels for open-cycle MHD generators, without being customized to the Sakhalin channel.

One way to improve the applicability of the presented model is to replace the prescribed regression function for the local plasma electric conductivity with a submodel that estimates the local plasma electric conductivity for an arbitrary thermal-equilibrium plasma medium, given its (1) chemical composition, (2) temperature, and (3) pressure.

Another way to extend this study is to perform sensitivity analyses of channel geometry parameters (such as the divergence angle and electrode length) to identify their influence and the opportunity to optimize the MHD channel.

One more way to improve the OpenFOAM MHD solver presented here is to address one or more of its limitations mentioned earlier.

Abbreviations
CADComputer-aided design
CCCTCombined-cycle gas turbine
CFDComputational fluid dynamics
DCDirect current
DPEDirect power extraction
ECEExternal combustion engine
FANSFavre-averaged Navier–Stokes equations
FSIFluid–structure interaction
FVMFinite volume method
GHGGreenhouse gas
HRSGHeat recovery steam generator
ICEInternal combustion engine
MHDMagnetohydrodynamics
OFCCOxy-fuel carbon capture
OOPObject-oriented programming
PGPlasma generator
PMHDGPulsed magnetohydrodynamic generator
PVPhotovoltaic
RANSReynolds-averaged Navier–Stokes equations
SPPSolid-propellant plasma
TEGThermoelectric generator
USSRUnion of Soviet Socialist Republics
Author contributions

O.M. is the single author of this manuscript.

Funding

Not applicable (this research received no funding).

Data availability

Data supporting this study is provided within the manuscript.

Declarations

Not applicable.

Not applicable.

Competing interests

The author declares that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper.

Received: 26 February 2025 / Accepted: 6 September 2025

Published online: 30 September 2025

References

Publisher's Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

References

  1. [1]Gruzdeva EJ. The Linguistic Situation on Sakhalin Island. In: Atlas of Languages of Intercultural Communication in the Pacific, Asia, and the Americas: Vol 1. Idoors P., M. Mühlhäusler, P. Tryon, D. T. (Eds). De Gruyter Mouton, 2011; pp. 1007–1012. https://doi.org/10.1515/97831108724.3.1007.
  2. [2]Syrbu N, Kholmogorov A, Stepochkin I, Lobanov V, Shkorba S. Formation of abnormal gas-geochemical fields and dissolved gases transport at the shallow northeastern shelf of Sakhalin Island in warm season: expedition data and remote sensing. Water. 2024;16(10):1434. https://doi.org/10.3390/w16101434.
  3. [3]Afonin AG, Butov VG, Panchenko VP, Sinyaev SV, Solonenko VA, Shvetsov GA, et al. Powerful pulsed magnetohydrodynamic generator fueled by a solid (powder) propellant of a new generation. J Appl Mech Tech Phys. 2018;59(6):1024–35. https://doi.org/10.1134/S0021894.18060081.
  4. [4]Panchenko VP. Peculiarities of Two-Phase Flow in Pulsed MHD Generators. In: 12th International Conference on MHD Electrical Power Generation; Yokohama, Japan, 1996; Vol. 1, pp. 972–980.
  5. [5]Yuhara M, Fujino T, Ishikawa M. Numerical Analysis of Effects of Liquid Particles on Plasmadynamics in a Large-Scale Pulsed MHD Generator. In: 35th AIAA Plasmadynamics and Lasers Conference; AIAA [American Institute of Aeronautics and Astronautics]: Portland, Oregon, USA, 2004; pp. AIAA-2004–2369. https://doi.org/10.2514/6.2004-2369.
  6. [6]Ishikawa M, Koshiba Y. Preliminary Analysis of Large Pulsed MHD Generator. In: 3th Workshop on Magnetoplasma Aerodynamics for Aerospace Applications; Moscow, Russia, 2001; pp. 276–281.
  7. [7]Marzouk OA. Detailed derivation of the scalar explicit expressions governing the electric field, current density, and volumetric power density in the four types of linear divergent MHD channels under a unidirectional applied magnetic field. Contemp Math. 2025;6(4):4060–100. https://doi.org/10.37526/cmath.640260519.
  8. [8]Angrist SW. Direct Energy Conversion, 4. ed.; Allyn and Bacon series in mechanical engineering and applied mechanics; Allyn and Bacon: Boston, Massachusetts, USA, 1982.
  9. [9]Marzouk OA. Thermoelectric generators versus photovoltaic solar panels: power and cost analysis. Edelweiss Appl Sci Technol. 2024;8(5):406–28. https://doi.org/10.55214/25768484.v8i5.1697.
  10. [10]Panchenko VP. Preliminary Analysis of the “Sakhalin” World Largest Pulsed MHD Generator. In 4th Workshop on Magnetoplasma Aerodynamics for Aerospace Applications; Moscow, Russia, 2002; pp. 322–331.DOI
  11. [11]Yakushev AA, Panchenko VP, Dyogtev VG, Dogadeyev RV, Gomozov VA, Ivanenko AA. Recent Experimental Researches of Combustion Products Plasma of Combined (Pyrotechnic) Propellant for Pulsed MHD Generators. In: 13th International Conference on MHD Electrical Power Generation and High Temperature Technologies; Beijing, China, 1999; Vol. 2, pp. 423–434.
  12. [12]Ishikawa M, Koshiba Y, Matsushita T. Effects of induced magnetic field on large scale pulsed MHD generator with two phase flow. Energy Convers Manag. 2004;45(5):707–24. https://doi.org/10.1016/S0196-8904(03)00182-1.
  13. [13]Dogadayev RV, Koroleva LA, Martinov BM, Panchenko VP, Yakushev AA, Bukhteyev LA. Experimental and Numerical Investigations of the Pulsed Solid Propellant Diagonal Type MHD Generator “Pamir-06.” In: 12th International Conference on MHD Electrical Power Generation; Yokohama, Japan, 1996; Vol. 1, pp 61–70.
  14. [14]Marzouk OA. Estimated electric conductivities of thermal plasma for air-fuel combustion and oxy-fuel combustion with potassium or cesium seeding. Heliyon. 2024;10(11):e31697. https://doi.org/10.1016/j.heliyon.2024.e31697.
  15. [15]Bong HK, Selvarajoo A, Arumugasamy SK. Stability of biochar derived from banana peel through pyrolysis as alternative source of nutrient in soil: feedforward neural network modelling study. Environ Monit Assess. 2022;194(2):70. https://doi.org/10.1007/s10661-021-09691-x.
  16. [16]Brockmeier U, Koch M, Unger H, Schütz W. Volatile fission product and sodium release from liquids. Nucl Eng Des. 1994;148(2):49–507. https://doi.org/10.1016/0029-5493(94)0129-5.
  17. [17]Li L, Wang J, Jia C, LV L, Liu Y. Co-pyrolysis of cyanobacteria and plastics to synthesize porous carbon and its application in methylene blue adsorption. J Water Process Eng. 2021;39:101753. https://doi.org/10.1016/j.jwpe.2020.101753.
  18. [18]Pasri S.I. Instruments for Earth Resistivity Measurement of the Subsoil. https://www.pasri.lt/с/en/earth-resistivity/geoelectrical-prospecting-electrical-imaging (accessed 2025–02–08).
  19. [19]Vorobyev V, Safarov I, Mostovoy P, Shakirayev V. Best Practices of Exploration: Integration of Seismic and Electrical Prospecting; OnePetro, 2019. https://doi.org/10.2118/196138-MS.
  20. [20]Mogilatov V, Balashov B. A new method of geoelectrical prospecting by vertical electric current soundings. J Appl Geophys. 1996;36(1):31–41. https://doi.org/10.1016/S0926-9851(96)00030-4.
  21. [21]Afonin AG, Butov VG, Sinyaev SV, Solonenko VA, Shvetsov GA, Stankevich SV. Rail electromagnetic launchers powered by pulsed MHD generators. IEEE Trans Plasma Sci. 2017;45(7):1208–12. https://doi.org/10.1109/TPS.2017.2702166.
  22. [22]Esposito N, Raugi M, Tellini A. MHD generators as pulse power sources for arc-driven railguns. IEEE Trans Magn. 1995;31(1):47–51. https://doi.org/10.1109/20.364730.
  23. [23]Harada Nob H, Hamada R. Preparations for Studies on Space Application of MHD Generation and Acceleration. In: 39th Aerospace Sciences Meeting and Exhibit; AIAA [American Institute of Aeronautics and Astronautics]: Reno, Nevada, USA, 2001; p AIAA–2001–0797. https://doi.org/10.2514/6.2001-797.
  24. [24]Zeigarnik VA, Novikov VA, Okunev VI, Rickman VYu. Potentialities of Application of Pulsed MHD Generators for Power Supply of Reusable Transport Space Systems with Horizontal Launching of Aerospace Plane. In: 33rd Plasmadynamics and Lasers Conference; AIAA [American Institute of Aeronautics and Astronautics]: Maui, Hawaii, USA, 2002; p AIAA 2002–2190. https://doi.org/10.2514/6.2002-2190.
  25. [25]Litchford RJ, Jones JE, Dobson CC, Cole JW, Thompson BR, Plemmons DH, Turner MW. Pulse Detonation Rocket MHD Power Experiment. In: 33rd Plasmadynamics and Lasers Conference; AIAA [American Institute of Aeronautics and Astronautics]: Maui, Hawaii, USA, 2002; p AIAA 2002–2231. https://doi.org/10.2514/6.2002-2231.
  26. [26]Saurabh A, Turan A. Computational analysis of 3D-flows in rocket produced H2/H2O plasma based MHD generators for space applications. Int J Space Sci Eng. 2013;1(3):290–310. https://doi.org/10.1504/IJSPACE.2013.058848.
  27. [27]Sugita H, Matsuo T, Inui Y, Ishikawa M. Two-Dimensional Analysis of Gas-Particle Two Phase Flow in Pulsed MHD Channel. In: 30th Plasmadynamic and Lasers Conference; American Institute of Aeronautics and Astronautics: Norfolk, Virginia, USA, 1999; pp. AIAA-99–3483. https://doi.org/10.2514/6.1999-3483.
  28. [28]Matsuo T, Sugita H, Ishikawa M, Zeigarnik VA. Boundary-Layer Separation and Generator Performance of Self-Excited Pulsed MHD Channel with Strong MHD Interaction. In: 13th International Conference on MHD Electrical Power Generation and High Temperature Technologies; Beijing, China, 1999; Vol. 2, pp 399–408.
  29. [29]Bababakov Ju, Eremenko V, Krivosheev N, Kuzmin R, Poljakov V, Pisakin A. Powerful Self-Contained Solid Propellant Fueled MHD Generator “Sojuz” for Area and Deep Geophysical Prospecting. In: 12th International Conference on MHD Electrical Power Generation; Yokohama, Japan, 1996; Vol. 1, pp. 445–450.
  30. [30]Novikov VA, Okunev VI, Rickman V Yu. 51. Feasibility Study of Application of Pulsed MHD Generators for Power Supply of Nasa Maglev Launch-Assist Electromagnetic Tracks. In: 3th Workshop on Magnetoplasma Aerodynamics for Aerospace Applications; Moscow, Russia, 2001; pp. 273–275.
  31. [31]Velikhov EP, Panchenko VP. Large-Scale Geophysical Surveys of the Earth’s Crust Using High-Power Electromagnetic Pulses. In: Handbook of Geophysical Exploration: Seismic Exploration: Elsevier, 2010; Vol. 40, pp. 29–53. https://doi.org/10.1016/S0950-1401(10)04007-3.
  32. [32]Sugita H, Matsuo T, Inui Y, Ishikawa M. Two-Dimensional Behavior of Gas-Particle Two-Phase Flow under Strong MHD Interaction. In: 13th International Conference on MHD Electrical Power Generation and High Temperature Technologies; Beijing, China, 1999; Vol. 2, pp 453–462.
  33. [33]Kayukawa N. Open-cycle magnetohydrodynamic electrical power generation: a review and future perspectives. Prog Energy Combust Sci. 2004;30(1):33–60. https://doi.org/10.1016/j.pecs.2003.08.003.
  34. [34]Marzouk OA. Hydrogen Utilization as a Plasma Source for Magnetohydrodynamic Direct Power Extraction (MHD-DPE). IEEE Access. 2024;12:167088–107. https://doi.org/10.1109/ACCESS.2024.3496796.
  35. [35]Wilson WW, Singh JP, Yueh FY, Bauman LE, George A, Cook RL, et al. Comparison of Velocity and Temperature Measurements in an MHD Topping Cycle Environment With Flow Field Model Calculations. Combust Sci Technol. 1995;109(1–6):1–22. https://doi.org/10.1080/00102209508951892.
  36. [36]Hustad C-W, Coleman DL, Mikus T. Technology Overview for Integration of an MHD Topping Cycle with the CES Oxyfuel Combustor; Final Report; CO2-Global, 2009. https://co2no.wp-content/uploads/2020/07/MHD_Report-Final.pdf (accessed 2011–06–12).
  37. [37]Bünde R, Muntenbruch H, Raeder J, Volk R, Zankl G. MHD Power Generation: Selected Problems of Combustion MHD Generators; Raeder, J., (Ed.), Springer: Berlin, 1975
  38. [38]Marzouk OA. Temperature-Dependent Functions of the Electron-Neutral Momentum Transfer Collision Cross Sections of Selected Combustion Plasma Species. Appl Sci. 2023;13(20):11282. https://doi.org/10.3390/app132011282.
  39. [39]Mori Y, Ohtake K, Yamamoto M, Imani K. Thermodynamic and Electrical Properties of Combustion Gas and Its Plasma : 1st Report. Theoret Calc Bullet JSME. 1968;11(44):241–52. https://doi.org/10.1299/jsme1958.11.241.
  40. [40]Kittijungjit T, Klamrassamee T, Laonoual Y, Sukjai Y. Comprehensive study on waste heat recovery from gas turbine exhaust using combined steam and organic Rankine cycles. Energy Convers Manag X. 2025;25:100825. https://doi.org/10.1016/j.ecmx.2024.100825.
  41. [41]Boretti A. Combined cycle gas turbine (CCGT) plants utilizing methane-hydrogen blends represent a significant element in Australia’s journey toward achieving net-zero emissions. Fuel. 2025;381:133339. https://doi.org/10.1016/j.fuel.2024.113339.
  42. [42]Marzouk OA. Reduced-order modeling (ROM) of a segmented plug-flow reactor (PFR) for hydrogen separation in integrated gasification combined cycles (IGCC). Processes. 2025;13(5):1455. https://doi.org/10.3390/pr13051455.
  43. [43]Marzouk OA. Assessment of global warming in Al Buraimi, Sultanate of Oman based on statistical analysis of NASA POWER data over 39 years, and testing the reliability of NASA POWER against meteorological measurements. Heliyon. 2021;7(3):e06625. https://doi.org/10.1016/j.heliyon.2021.e06625.
  44. [44]Meinshausen M, Meinshausen N, Hare W, Raper SCB, Frieler K, Knutti R, et al. Greenhouse-gas emission targets for limiting global warming to 2 °C. Nature. 2009;458(7242):1158–62. https://doi.org/10.1038/nature08017.
  45. [45]Marzouk OA. Chronologically-Ordered Quantitative Global Targets for the Energy-Emissions-Climate Nexus, from 2021 to 2050. In: 2022 International Conference on Environmental Science and Green Energy (ICESGE); IEEE [Institute of Electrical and Electronics Engineers]: Shenyang, China (and Virtual), 2022; pp. 1–6. https://doi.org/10.1109/ICESGE56040.2022.10180322.
  46. [46]Marzouk OA. Zero carbon ready metrics for a single-family home in the Sultanate of Oman Based on EDGE Certification System for Green Buildings. Sustainability. 2023;15(18):13856. https://doi.org/10.3390/su151813856.
  47. [47]Kim Y, Kim T, Lee I, Park J. Liquid air energy storage system with oxy-fuel combustion for clean energy supply: comprehensive energy solutions for power, heating, cooling, and carbon capture. Appl Energy. 2025;379:124937. https://doi.org/10.1016/j.apenergy.2024.124937.
  48. [48]Marzouk OA. Technical review of radiative-property modeling approaches for gray and nongray radiation, and a recommended optimized WSGGM for CO2/H2O-enriched gases. Results Eng. 2025;25:103923. https://doi.org/10.1016/j.rineng.2025.103923.
  49. [49]Raho B, Giangreco M, Colangelo G, Milanese M, de Risi A. Technological, economic, and emission analysis of the oxy-combustion stir process. Appl Energy. 2025;378:124821. https://doi.org/10.1016/j.apenergy.2024.124821.
  50. [50]Marzouk OA. Radiant Heat Transfer in Nitrogen-Free Combustion Environments. Int J Nonlinear Sci Num Simul. 2018;19(2):175–88. https://doi.org/10.1515/ijnsns-2017-0106.
  51. [51]Ork K, Masuda R, Okuno Y. Fundamental experiment and numerical simulation of Ne/Xe plasma magnetohydrodynamic electrical power generation. J Propuls Power. 2024;40(3):368–79. https://doi.org/10.2514/1.B39352.
  52. [52]Marzouk OA. Adiabatic flame temperatures for oxy-methane, oxy-hydrogen, air-methane, and air-hydrogen stoichiometric combustion using the NASA CEARUN tool, GRI-mech 3.0 reaction mechanism, and Cantera Python package. Eng Technol Appl Sci Res. 2023;13(4):11437–44. https://doi.org/10.48084/etasr.6312.
  53. [53]Bian J-Y, Guo X-Y, Lee DH, Sun X-R, Liu L-S, Shao K, et al. Non-thermal plasma enhances rice seed germination, seedling development, and root growth under low-temperature stress. Appl Biol Chem. 2024;67(1):2. https://doi.org/10.1186/s1376 5-023-00852-9.
  54. [54]Guragain RP, Kierzkowska-Pawlak H, Fronczak M, Kędzierska-Sar A, Subedi DP, Tyczkowski J. Germination Improvement of Fenugreek Seeds with Cold Plasma: Exploring Long-Lasting Effects of Surface Modification. Sci Hortic. 2024;324:112619. https://doi.org/10.1016/j.scienta.2023.112619.
  55. [55]Yousefi H, Mahmoudi M, Ghodosinejad MH. Modeling and sensitivity analysis of a supersonic inductive magnetohydrodynamic (MHD) generator. futech. 2024;3(2):1–10. https://doi.org/10.55670/fpll.futech.3.2.1.
  56. [56]Marzouk OA. Energy Generation Intensity (EGI) for Parabolic Dish/Engine Concentrated Solar Power in Muscat, Sultanate of Oman. IOP Conf Ser Earth Environ Sci. 2022;1008(1):012013. https://doi.org/10.1088/1755-1315/1008/1/012013.
  57. [57]Wang Y, Cheng K, Xu J, Jing W, Huang H, Qin J. Thermodynamic and mass analysis of a novel two-phase liquid metal MHD enhanced energy conversion system for space nuclear power source. Energy. 2024;308:132860. https://doi.org/10.1016/j.energy.2024.132860
  58. [58]Marzouk OA. Land-use competitiveness of photovoltaic and concentrated solar power technologies near the Tropic of Cancer. Sol Energy. 2022;243:103–19. https://doi.org/10.1016/j.solener.2022.07.051.
  59. [59]Feng Y, Shi XJ, Lu XQ, Sun W, Liu KP, Fei YF. Study on scooping failure of gas turbine ball bearing based on 3D mixed lubrication and dynamics. Proc Inst Mech Eng Part J J Eng Tribol. 2024;238(8):897–911. https://doi.org/10.1177/13506501241242151.
  60. [60]Marzouk OA. One-way and two-way couplings of CFD and structural models and application to the wake-body interaction. Appl Math Model. 2011;35(3):1036–53. https://doi.org/10.1016/j.apm.2010.07.049.
  61. [61]Gbashi SM, Olatunji OO, Adejeji PA, Madhushe NE. From academic to industrial research: a comparative review of advances in rolling element bearings for wind Turbine Main Shaft. Eng Fail Anal. 2024;163:108510. https://doi.org/10.1016/j.engfailanal.2024.108510.
  62. [62]Marzouk OA. Facilitating digital analysis and exploration in solar energy science and technology through free computer applications. Eng Proc. 2022;31(1):75. https://doi.org/10.3390/ASEC2022-13920.
  63. [63]Domínguez-Lozoya JC, Domínguez-Lozoya DR, Cuevas S, Ávalos-Zúñiga RA. Mhd generation for sustainable development, from thermal to wave energy conversion: review. Sustainability. 2024;16(22):10041. https://doi.org/10.3390/su162210041.
  64. [64]Marzouk OA. Lookup tables for power generation performance of photovoltaic systems covering 40 geographical locations (wilayats) in the Sultanate of Oman, with and without solar tracking, and general perspectives about solar irradiation. Sustainability. 2013;13(23):13209. https://doi.org/10.3390/su132313209.
  65. [65]Barik PR, Praveenkumar S. Experimental Analysis on the Thermoelectric Effect of Various Solid-State Devices Used for Direct Conversion of Thermal Energy into Electrical Energy. Results Eng. 2024;23:102752. https://doi.org/10.1016/j.rineng.2024.102752.
  66. [66]Marzouk OA. Tilt Sensitivity for a Scalable One-Hectare Photovoltaic Power Plant Composed of Parallel Racks in Muscat. Cogent Eng. 2022;9(1):2092943. https://doi.org/10.1080/23311916.2022.2092943.
  67. [67]Demirbas A, Meydan F. Utilization of biomass as alternative fuel for external combustion engines. Energy Sources. 2004;26(13):1219–26. https://doi.org/10.1080/00908310490268065.
  68. [68]Marzouk OA. Urban air mobility and flying cars: overview, examples, prospects, drawbacks, and solutions. Open Eng. 2022;12(1):662–79. https://doi.org/10.1515/eng-2022-0379.
  69. [69]AERL [Avco Everett Research Laboratory]. MHD Generator Component Development. Quarterly Report, January–March 1977; FE-2519–1, 5224888; Avco Everett Research Laboratory, Inc.: USA, 1977; pp. FE-2519–1, 5224888. https://doi.org/10.2172/5224888.
  70. [70]Marzouk OA. Jatropha curcas as marginal land development crop in the Sultanate of Oman for producing biodiesel, biogas, briquettes, animal feed, and organic fertilizer. Rev Agric Sci. 2020;8:109–23. https://doi.org/10.7831/ras.8_0_109.
  71. [71]Palmer H, Beér JM. Combustion technology: some modern developments. New York: City, New York, USA: Elsevier; 2012.
  72. [72]Marzouk OA. Levelized cost of Green Hydrogen (LCOH) in the Sultanate of Oman using H2A-lite with polymer electrolyte membrane (PEM) electrolyzers powered by solar photovoltaic (PV) electricity. E3S Web Conf. 2023;469:00101. https://doi.org/10.1051/e3sconf/202346900101.
  73. [73]Marzouk OA. 2030 Ambitions for Hydrogen, Clean Hydrogen, and Green Hydrogen. Eng Proc. 2023;56(1):14. https://doi.org/10.3390/ASEC2023-15497.
  74. [74]Marzouk OA. Energy Generation Intensity (EGI) of Solar Updraft Tower (SUT) Power Plants Relative to CSP Plants and PV Power Plants Using the New Energy Simulator “Aladdin”. Energies. 2024;17(2):405. https://doi.org/10.3390/en17020405.
  75. [75]Patonia A. Green hydrogen and its unspoken challenges for energy justice. Appl Energy. 2025;357:124674. https://doi.org/10.1016/j.apenergy.2024.124674.
  76. [76]Marzouk OA. Compilation of Smart Cities Attributes and Quantitative Identification of Mismatch in Rankings. J Eng. 2022;2022:5981551. https://doi.org/10.1155/2022/5981551.
  77. [77]Marzouk OA. Exploring the role of hydrogen and its derivatives in different sectors through analysis of the four energy scenarios: IEA-STEPS, IEA-NZE, IRENA-PES, and IRENA-1.5°C. Energies. 2024;17(3):646. https://doi.org/10.3390/en17030646.
  78. [78]Schmidt H, Lineberry J, Crawford L. Design Criteria for High Performance MHD Generator Utilizing Energetic Fuels. In: 25th AIAA Aerospace Sciences Meeting; American Institute of Aeronautics and Astronautics: Reno, Nevada, USA, 1987. https://doi.org/10.2514/6.1987-3882.
  79. [79]Marzouk OA. Portrait of the decarbonization and renewables penetration in Oman’s energy mix, motivated by Oman’s national green hydrogen plan. Energies. 2024;17(19):4769. https://doi.org/10.3390/en17194769.
  80. [80]Chapman J, Erb D, Crawford L, Johanson N. Use of Natural Gas as Fuel for MHD Central Power Generation. In: Intersociety Energy Conversion Engineering Conference; AIAA [American Institute of Aeronautics and Astronautics]: Monterey, California, USA, 1994; pp. AIAA-94–3907-CP. https://doi.org/10.2514/6.1994-3907.
  81. [81]Marzouk OA. Performance Analysis of Shell-and-Tube Dehydrogenation Module. Int J Energy Res. 2017;41(4):604–10. https://doi.org/10.1002/er.3637.
  82. [82]Way S, DeCorso SM, Hundstad RL, Kemeny GA, Stewart W, Young WE. Experiments with MHD power generation. J Eng Power. 1961;83(4):397–408. https://doi.org/10.1115/1.3637218.
  83. [83]Brogan TR, Louis JF, Ros RJ, Stekly ZJ. A Review of Recent MHD Generator Work at the Avco-Everett Research Laboratory. In: Third Symposium on the Engineering Aspects of Magnetohydrodynamics; Armed Services Technical Information Agency: Rochester, New York, USA, 1962; pp 1–20.
  84. [84]Ibberson VJ, Beér JM, Swithenbank J, Taylor DS, Thring MW. A combustion oscillator for MHD energy conversion. Symp (Int) Combust. 1971;13(1):565–72. https://doi.org/10.1016/S0082-0784(71)80058-9.
  85. [85]Rosa RJ. MHD Power Generation: State of the Art and Prospects for Advanced Nuclear Applications; Thom, K., Schneider, R. T., Eds.; NASA [United States National Aeronautics and Space Administration]: Gainesville, Florida, USA, 1970; pp 315–326.
  86. [86]Galanga FL, Lineberry TJ, Wu YCL, Scott MH, Baucum WE, Clemons RW. Experimental Results of the UTSI Coal-Fired MHD Generator and Investigations of Various Power Take-off Schemes. In: 19th Aerospace Sciences Meeting; AIAA [American Institute of Aeronautics and Astronautics]: St. Louis, Missouri, USA, 1981. https://doi.org/10.2514/6.1981-30.
  87. [87]Im KH, Ahluwalia RK. Convective and radiative heat transfer in MHD radiant boilers. Journal of Energy. 1981;5(5):308–14. https://doi.org/10.2514/3.48037.
  88. [88]Doney et al., M. K. C. Energy Education/Boiler slag. https://energyeducation.ca/encyclopedia/Boiler_slag (accessed 2025–02–10).
  89. [89]Pintana P, Tippayawong N, Nuntaphun A, Thongchiew P. Characterization of slag from combustion of pulverized lignite with high calcium content in utility boiler. Energy Explor Exploit. 2014;32(3):471–82. https://doi.org/10.1260/0144-5987.32.3.471.
  90. [90]Mahboobti M, Mirzagoli Ganji A, Jalili P, Jalili B, Ahmad I, Hendy AS, et al. Investigate the influence of various parameters on MHD flow characteristics in a porous medium. Case Stud Therm Eng. 2024;59:104428. https://doi.org/10.1016/j.csite.2024.104428.
  91. [91]Ahmad S, Cham BM, Liu D, Islam SU, Hussien MA, Waqas H. Numerical analysis of heat and mass transfer of MHD natural convection flow in a cavity with effects of source and sink. Case Stud Therm Eng. 2024;53:103926. https://doi.org/10.1016/j.csite.2024.103926.
  92. [92]Alotaibi MA, El-Sapa S. MHD couple stress fluid between two concentric spheres with slip regime. Results Eng. 2024;21:101934. https://doi.org/10.1016/j.rineng.2024.101934.
  93. [93]Alomari MA, Al-Farhany K, Al-Salami QH, Ali IR, Biswas N, Mohamed MH, et al. Numerical analysis to investigate the effect of a porous block on MHD mixed convection in a split lid-driven cavity with nanofluid. International Journal of Thermofluids. 2024;22:100621. https://doi.org/10.1016/j.ijft.2024.100621.
  94. [94]Dharmendar Reddy Y, Nagi Reddy N, Goud BS. Suction and Double Stratification Effect on Unsteady MHD Heat Transfer Nanofluid Flow over a Flat Surface. Results in Engineering. 2024;23:102431. https://doi.org/10.1016/j.rineng.2024.102431.
  95. [95]Greenshields, C. OpenFOAM v12 User Guide. CFD Direct. https://doc.cfd.direct/openfoam/user-guide-v12/programming-language-openfoam (accessed 2025–02–18).
  96. [96]Greenshields C. OpenFOAM user guide, vol. 12. London, UK: The OpenFOAM Foundation; 2024.
  97. [97]OpenCFD. OpenFOAM® Documentation. https://www.openfoam.com/documentation/overview (accessed 2024–11–19).
  98. [98]Jasak H. OpenFOAM: Open source CFD in research and industry. Int J Nav Archit Ocean Eng. 2009;1(2):89–94. https://doi.org/10.2478/IJNAOE-2013-0011.
  99. [99]Weller HG, Tabor G, Jasak H, Fureby C. A tensorial approach to computational continuum mechanics using object-oriented techniques. Comput Phys. 1998;12(6):620–31. https://doi.org/10.1063/1.168744.
  100. [100]Lysenko DA, Ertesvåg IS, Rian KE. Modeling of turbulent separated flows using OpenFOAM. Comput Fluids. 2013;80:408–22. https://doi.org/10.1016/j.compfluid.2012.01.015.
  101. [101]Marzouk OA, Huckaby ED. Modeling Confined Jets with Particles and Swirl. In: Machine Learning and Systems Engineering; Ao, S-I., Rieger, B., Amouzegar, M. A., (Eds.), Lecture Notes in Electrical Engineering; Springer Netherlands: Dordrecht, Netherlands, 2010; Vol. 68, pp. 243–256. https://doi.org/10.1007/978-90-481-9419-3_19.
  102. [102]Robertson E, Choudhury V, Bhushan S, Walters DK. Validation of OpenFOAM numerical methods and turbulence models for incompressible bluff body flows. Comput Fluids. 2015;123:122–45. https://doi.org/10.1016/j.compfluid.2015.09.010.
  103. [103]Marzouk OA, Huckaby ED. Assessment of Syngas Kinetic Models for the Prediction of a Turbulent Nonpremixed Flame. In: Fall Meeting of the Eastern States Section of the Combustion Institute 2009; College Park, Maryland, USA, 2009; pp 726–751.
  104. [104]Chen LF, Zang J, Hillis AJ, Morgan GJ, Plummer AR. Numerical investigation of wave-structure interaction using OpenFOAM. Ocean Eng. 2014;88:591–109. https://doi.org/10.1016/j.oceaneng.2014.06.003.
  105. [105]Liu K, Wang M, Gan F, Tian W, Qiu S, Su GH. Numerical Investigation of Flow and Heat Transfer Characteristics in Plate-Type Fuel Channels of IAEA MTR Based on OpenFOAM. Prog Nucl Energy. 2021;141:103963. https://doi.org/10.1016/j.pnucene.2021.103963.
  106. [106]Cockburn B, Coquel F, LeFloch PG. Convergence of the finite volume method for multidimensional conservation laws. SIAM J Numer Anal. 1995;32(3):687–705. https://doi.org/10.1137/0732032.
  107. [107]Chandrasekhar P, Garg A. Vertex-centroid finite volume scheme on tetrahedral grids for conservation laws. Comput Math Appl. 2013;65(1):58–74. https://doi.org/10.1016/j.camwa.2012.10.013.
  108. [108]Marzouk OA, Nayfeh AH. Control of ship roll using passive and active anti-roll tanks. Ocean Eng. 2009;36(9):661–71. https://doi.org/10.1016/j.oceaneng.2009.03.005.
  109. [109]Shahidiana G, Ghassemi M. Effect of magnetic flux density and other properties on temperature and velocity distribution in Magnetohydrodynamic (MHD) pump. IEEE Trans Magn. 2009;45(1):298–301. https://doi.org/10.1109/TMAG.2008.2008614.
  110. [110]Sriram AT, Chakraborty D. Numerical Exploration of Staged Transverse Injection into Confined Supersonic Flow behind a Backward-Facing Step. Def Sci J. 2011;61(1):3–11.
  111. [111]Marzouk OA. Flow control using bifrequency motion. Theor Comput Fluid Dyn. 2011;25(6):381–405. https://doi.org/10.1007/s00162-010-0206-6.
  112. [112]Pirumov UG. Three-Dimensional Sub- and Supersonic Flows in Nozzles and Channels of Varying Cross Section: PMM Vol 36, №2, 1972, pp239–247. J Appl Math Mech. 1972;36(2):220–9. https://doi.org/10.1016/0021-8928(72)90161-X.
  113. [113]Marzouk OA. Benchmarking retention, progression, and graduation rates in undergraduate higher education across different time windows. Cogent Education. 2025;12(1):2498170. https://doi.org/10.1080/2331186X.2025.2498170.
  114. [114]Marzouk OA. Benchmarks for the Omani Higher Education Students-Faculty Ratio (SFR) based on World Bank data, QS rankings, and THE rankings. Cogent Educ. 2024;11(1):2317117. https://doi.org/10.1080/2331186X.2024.2317117.
  115. [115]Marzouk OA. Accrediting Artificial Intelligence Programs from the Omani and the International ABET Perspectives. In Intelligent Computing; Arai, K., (Ed.), Lecture Notes in Networks and Systems; Springer International Publishing: Cham, Switzerland, 2021; Vol. 285, pp. 462–474. https://doi.org/10.1007/978-3-030-80129-8_33.
  116. [116]Nibideta B, Irfan M. Energy mix diversification in emerging economies: an econometric analysis of determinants. Renew Sustain Energy Rev. 2024;189:114043. https://doi.org/10.1016/j.rser.2023.114043.
  117. [117]Marzouk OA. Globalization and Diversity Requirement in Higher Education. In: The 11th World Multi-Conference on Systemics, Cybernetics and Informatics (WMSCI 2007) – The 13th International Conference on Information Systems Analysis and Synthesis (ISAS 2007); IIIS [International Institute of Informatics and Systemics]: Orlando, Florida, USA, 2007; Vol. II (3), pp. 101–106.
  118. [118]Lineberry JT, Schmidt HJ, Chapman JN. Experimental Program for Investigation of High Power Density MHD. In: Proceedings of the 24th Intersociety Energy Conversion Engineering Conference; 1989; pp 1085–1090 vol.2. https://doi.org/10.1109/9.IEC.1989.74602.
  119. [119]Schmidt H, Lineberry JT, Chapman JN. An Innovative Demonstration of High Power Density in a Compact MHD (Magnetohydrodynamic) Generator; DOE/PC/79678-T4; Tennessee Univ., Tullahoma, TN (USA). Space Inst., 1990. https://doi.org/10.2172/6294329.
  120. [120]Schmidt H, Lineberry J, Chapman J. High-Power Density MHD Experiments. In: 28th Aerospace Sciences Meeting; AIAA [American Institute of Aeronautics and Astronautics]; Reno, Nevada, USA, 1990. https://doi.org/10.2514/6.1990-345.
  121. [121]Marzouk OA. Aerial e-mobility perspective: anticipated designs and operational capabilities of eVTOL urban air mobility (UAM) aircraft. Edelweiss Appl Sci Technol. 2025;9(1):413–42. https://doi.org/10.55214/25768484.v9i1.4156.
  122. [122]Marzouk OA. Growth in the worldwide stock of E-mobility vehicles (by technology and by transport mode) and the worldwide stock of hydrogen refueling stations and electric charging points between 2020 and 2022. Key Eng Mater. 2023;972:89–96. https://doi.org/10.4028/p-8IMGm4.
  123. [123]Marzouk OA. Recommended LEED-Compliant Cars, SUVs, Vans, Pickup Trucks, Station Wagons, and Two Seaters for Smart Cities Based on the Environmental Damage Index (EDX) and Green Score. In: Innovations in Smart Cities Applications Volume 7; Ben Ahmed, M., Boudhir, A. A., El Meouhche, R., Karaş, I. R., (Eds.), Lecture Notes in Networks and Systems; Springer Nature Switzerland: Cham, Switzerland, 2024; Vol. 906, pp. 123–135. https://doi.org/10.1007/978-3-031-53824-7_12.
  124. [124]Marzouk OA. Toward More Sustainable Transportation: Green Vehicle Metrics for 2023 and 2024 Model Years. In Intelligent Sustainable Systems; Nagar, A. K., Jat, D. S., Mishra, D. K., Joshi, A., (Eds.), Lecture Notes in Networks and Systems; Springer Nature Singapore: Singapore, 2024; Vol. 817, pp. 261–272. https://doi.org/10.1007/978-981-99-7886-1_23.
  125. [125]Marzouk OA. Summary of the 2023 (1st edition) report of TCEP (tracking clean energy progress) by the International Energy Agency (IEA), and proposed process for computing a single aggregate rating. E3S Web Conf. 2025;601:00048. https://doi.org/10.1051/e3sconf/202560100048.
  126. [126]Marzouk OA. Evolution of the (Energy and Atmosphere) credit category in the LEED green buildings rating system (for Building Design and Construction: New Construction), from version 4.0 to version 4.1. J Infrastruct Policy Dev. 2024;8(8):5306. https://doi.org/10.24294/jipd.v8i8.5306.
  127. [127]Marzouk OA. Power density and thermochemical properties of hydrogen magnetohydrodynamic (H2MHD) generators at different pressures, seed types, seed levels, and oxidizers. Hydrogen. 2025;6(2):31. https://doi.org/10.3390/hydrogen6020031.
  128. [128]Choubey G, Tiwari M. Chapter Six—Pedagogy for the Computational Approach in Simulating Supersonic Flows. In: Scramjet Combustion; Choubey, G., Tiwari, M., Eds.; Butterworth-Heinemann, 2022; pp. 163–181. https://doi.org/10.1016/B978-0-323-99565-8.00007-0.
  129. [129]Garcia-Rodas LF, Alonso DH, Silva ECN. Turbulence effects in the topology optimization of compressible subsonic flow. Int J Numer Methods Fluids. 2025;97(1):44–68. https://doi.org/10.1002/fld.5338.
  130. [130]Marzouk OA, Nayfeh AH. Reduction of the loads on a cylinder undergoing harmonic in-line motion. Phys Fluids. 2009;21(8):083103. https://doi.org/10.1063/1.3210774.
  131. [131]Lodares D, Manzanero J, Ferrer E, Valero E. An entropy-stable discontinuous Galerkin approximation of the Spalart–Allmaras turbulence model for the compressible Reynolds averaged Navier–Stokes equations. J Comput Phys. 2022;455:110998. https://doi.org/10.1016/j.jcp.2022.110998.
  132. [132]Blazek J. Chapter 7—Turbulence Modeling. In Computational Fluid Dynamics: Principles and Applications (Third Edition); Blazek, J., Ed.; Butterworth-Heinemann: Oxford, 2015; pp. 213–252. https://doi.org/10.1016/B978-0-08-099995-1.00007-5.
  133. [133]Marzouk OA, Nayfeh AH. Characterization of the flow over a cylinder moving harmonically in the cross-flow direction. Int J Non-Linear Mech. 2020;45(8):821–33. https://doi.org/10.1016/j.ijnonlinmec.2010.06.004.
  134. [134]Baker C, Johnson T, Flynn D, Hemida H, Quinn A, Soper D, Sterling M. Chapter 4—Computational Techniques. In: Train Aerodynamics; Baker, C., Johnson, T., Flynn, D., Hemida, H., Quinn, A., Soper, D., Sterling, M., Eds.; Butterworth-Heinemann, 2019; pp. 53–71. https://doi.org/10.1016/B978-0-12-813310-1.00004-6.
  135. [135]Maida A. A Compressible Fluid Flow and Systems of Conservation Laws in Several Space Variables; Springer Science & Business Media, 2012.
  136. [136]Marzouk OA. Direct numerical simulations of the flow past a cylinder moving with sinusoidal and nonsinusoidal profiles. J Fluids Eng. 2009;131(12):121201. https://doi.org/10.1115/1.4000406.
  137. [137]Fletcher CAJ. Computational Techniques for Fluid Dynamics - Volume II: Specific Techniques for Different Flow Categories, 2nd ed.; Scientific Computation; Springer Berlin Heidelberg: Berlin, Heidelberg, 1991. https://doi.org/10.1007/978-3-642-58239-4.
  138. [138]Marzouk OA. Characteristics of the flow-induced vibration and forces with 1- and 2-DOF vibrations and limiting solid-to-fluid density ratios. J Vib Acoust. 2010;132(4):041013. https://doi.org/10.1115/1.4001503.
  139. [139]Rothan YA. Thermal management of nanofluid flow through porous container with impose of Lorentz force. Case Stud Therm Eng. 2024;60:104779. https://doi.org/10.1016/j.csite.2024.104779.
  140. [140]Bereanu C. Interactions in the Lorentz Force Equation. Calc Var. 2024;63(2):29. https://doi.org/10.1007/s00526-023-02635-y.
  141. [141]Mansour K, Khorsandi M. The drag reduction in spherical spiked blunt body. Acta Astronaut. 2014;99:92–8. https://doi.org/10.1016/j.actaastro.2014.02.009.
  142. [142]Marzouk OA, Nayfeh AH. A Study of the Forces on an Oscillating Cylinder. In: ASME 2007 26th International Conference on Offshore Mechanics and Arctic Engineering (OMAE 2007); ASME (American Society of Mechanical Engineers): San Diego, California, USA, 2009; pp. 741–752. https://doi.org/10.1115/OMAE2007-29163.
  143. [143]Li Y, Huang J, Xie C, Zhao H. CFD–DEM simulation on the main-controlling factors affecting proppant transport in three-dimensional rough fractures of offshore unconventional reservoirs. J Mar Sci Eng. 2024;12(12):2117. https://doi.org/10.3390/jmse12122117.
  144. [144]Marzouk OA. Contrasting the Cartesian and Polar Forms of the Shedding-Induced Force Vector in response to 12 subharmonic and superharmonic mechanical excitations. Fluid Dyn Res. 2010;42(3):035507. https://doi.org/10.1088/0169-5983/42/3/035507.
  145. [145]Ge L, Dasi LP, Sotiropoulos F, Yoganathan AP. Characterization of hemodynamic forces induced by mechanical heart valves: Reynolds vs. viscous stresses. Ann Biomed Eng. 2008;36(2):276–97. https://doi.org/10.1007/s10439-007-9411-x.
  146. [146]Marzouk OA, Nayfeh AH. New Wake Models With Capability of Capturing Nonlinear Physics. In: ASME 2008 27th International Conference on Offshore Mechanics and Arctic Engineering (OMAE 2008); ASME [American Society of Mechanical Engineers]: Estoril, Portugal, 2009; pp. 901–912. https://doi.org/10.1115/OMAE2008-57714.
  147. [147]Grosse AV. The reduced dynamic and kinematic viscosities of the metals—mercury, sodium and potassium—over their entire liquid range, i.e., from the melting point to the critical point, and a comparison with van der Waals’ substances. J Ind Nucl Chem. 1965;27(5):979–87. https://doi.org/10.1016/0022-1902(65)80407-9.
  148. [148]Marzouk OA, Nayfeh AH. Loads on a Harmonically Oscillating Cylinder. In: ASME 2007 International Design Engineering Technical Conferences and Computers and Information in Engineering Conference (IDETC-CIE 2007); ASME [American Society of Mechanical Engineers]: Las Vegas, Nevada, USA, 2009; pp. 1755–1774. https://doi.org/10.1115/DETC2007-35562.
  149. [149]Smith JD, Lora M, Hixson EM, Eldredge T. CFD in burner development. In: Baukal J, Charles E, editors. Industrial burners handbook. Boca Raton, Florida, USA: CRC Press; 2003. p. 145–88.
  150. [150]Weinert U. Spherical tensor representation. Arch Rational Mech Anal. 1980;74(2):165–96. https://doi.org/10.1007/BF00253328.
  151. [151]Marzouk OA, Nayfeh AH. Hydrodynamic Forces on a Moving Cylinder with Time-Dependent Frequency Variations. In: 46th AIAA Aerospace Sciences Meeting and Exhibit; AIAA [American Institute of Aeronautics and Astronautics]: Reno, Nevada, USA, 2008; pp AIAA 2008–680. https://doi.org/10.2514/6.2008-680.
  152. [152]Fan Y, Kozul M, Li W, Sandberg RD. Eddy-viscosity-improved resolvent analysis of compressible turbulent boundary layers. J Fluid Mech. 2024;983:A46. https://doi.org/10.1017/jfm.2024.174.
  153. [153]Marzouk OA. A nonlinear ODE system for the unsteady hydrodynamic force—a new approach. World Acad Sci Eng Technol. 2009;39:948–62.
  154. [154]Kosker M, Yilmaz F. The cross-sectional curvature effect of twisted tapes on heat transfer performance. Chem Eng Process-Process Intensif. 2020;154:108008. https://doi.org/10.1016/j.cep.2020.108008.
  155. [155]Marzouk OA, Nayfeh AH. Fluid Forces and Structure-Induced Damping of Obliquely-Oscillating Offshore Structures. In: The Eighteenth (2008) International Offshore and Polar Engineering Conference (ISOPE-2008); ISOPE [International Society of Offshore and Polar Engineers]: Vancouver, British Columbia, Canada, 2008; Vol. 3, pp. 460–468.
  156. [156]Hu XY, Adams NA. A SPH model for incompressible turbulence. Procedia IUTAM. 2015;18:66–75. https://doi.org/10.1016/j.piutam.2015.11.007.
  157. [157]Marzouk OA, Nayfeh AH. A Parametric Study and Optimization of Ship-Stabilization Systems. In: 1st WSEAS International Conference on Maritime and Naval Science and Engineering (MN’08); WSEAS [World Scientific and Engineering Academy and Society]: Malta, 2008; pp. 169–174.
  158. [158]Linke A. A divergence-free velocity reconstruction for incompressible flows. C R Math. 2012;350(17):837–40. https://doi.org/10.1016/j.crma.2012.10.010.
  159. [159]Marzouk OA, Nayfeh AH. Mitigation of Ship Motion Using Passive and Active Anti-Roll Tanks. In: ASME 2007 International Design Engineering Technical Conferences and Computers and Information in Engineering Conference (IDETC-CIE 2007); ASME [American Society of Mechanical Engineers]: Las Vegas, Nevada, USA, 2009; pp. 215–229. https://doi.org/10.1115/DETC2007-35571.
  160. [160]Ma H, Chen H-C. Enhancing the two-layer k-epsilon turbulence model through rough wall modification. Phys Fluids. 2014;26(10):105151. https://doi.org/10.1063/5.0232725.
  161. [161]Marzouk OA, Huckaby ED. Effects of Turbulence Modeling and Parcel Approach on Dispersed Two-Phase Swirling Flow. In: World Congress on Engineering and Computer Science 2009 (WCECS 2009); IAENG [International Association of Engineers]: San Francisco, California, USA, 2009; Vol. II, pp. 1–11.
  162. [162]Ashwin Ganesh M, John B. Concentrated energy addition for active drag reduction in hypersonic flow regime. Acta Astronaut. 2018;142:221–31. https://doi.org/10.1016/j.actaastro.2017.11.003.
  163. [163]Marzouk OA. A two-step computational aeroacoustics method applied to high-speed flows. Noise Control Eng J. 2008;56(5):396. https://doi.org/10.3397/1.2978229.
  164. [164]Camberos J. Energy Analysis Applied to External Aerodynamics of High-Speed Flow. In: 9th AIAA/ASME Joint Thermophysics and Heat Transfer Conference; American Institute of Aeronautics and Astronautics: San Francisco, California, USA, 2006; pp. AIAA 2006–2943. https://doi.org/10.2514/6.2006-2943.
  165. [165]Marzouk OA. Directivity and Noise Propagation for Supersonic Free Jets. In: 46th AIAA Aerospace Sciences Meeting and Exhibit; AIAA [American Institute of Aeronautics and Astronautics]: Reno, Nevada, USA, 2008; pp AIAA 2008–23. https://doi.org/10.2514/6.2008-23.
  166. [166]Foundations to Heat Transfer, 6. ed., Internat. student version.; Incropera, F. P., DeWitt, D. P., Bergman, T. L., Lavine, A. S., (Eds.), Wiley: Singapore, 2013.
  167. [167]Schlichting H, Gersten K. Boundary-Layer Theory. Springer Berlin Heidelberg: Berlin, Heidelberg, 2000. https://doi.org/10.1007/978-3-642-85829-1.
  168. [168]Schwab A, Fuchs C, Kistenmacher P. Semantics of the irrotational component of the magnetic vector potential. A IEEE Antennas Propag Magazine. 1999;39(1):46–51. https://doi.org/10.1109/74.583518.
  169. [169]Matsushita T. Electrostatic Field. In: Electricity and Magnetism: New Formulation by Introduction of Superconductivity; Matsushita, T., (Ed.), Springer International Publishing: Cham, 2021; pp. 3–32. https://doi.org/10.1007/978-3-030-82150-0_1.
  170. [170]Marzouk OA. A Detailed and simplified plasma models in combined-cyclone magnetohydrodynamic power systems. Int J Adv Appl Sci. 2023;10(11):96–108. https://doi.org/10.21833/ijaas.2023.11.013.
  171. [171]Laney CB. Computational gasdynamics. 1st ed. USA: Cambridge University Press; 1998. https://doi.org/10.1017/CBO9780511605604.
  172. [172]Griffiths JF, Barnard JA. Flame and combustion. 3rd ed. Boca Raton, Florida, USA: Routledge; 1995.
  173. [173]Marzouk OA. Noise Emissions from Excited Jets. In: 22nd National Conference on Noise Control Engineering (NOISE-CON 2007); INCE [Institute of Noise Control Engineering]: Reno, Nevada, USA, 2007; pp. 1034–1045.
  174. [174]Zucker RD, Biblarz O. Fundamentals of gas dynamics, vol. 3. USA: John Wiley & Sons; 2019.
  175. [175]Marzouk OA. Investigation of Strouhal Number Effect on Acoustic Fields. In: 22nd National Conference on Noise Control Engineering (NOISE-CON 2007); INCE [Institute of Noise Control Engineering]: Reno, Nevada, USA, 2007; pp. 1056–1067.
  176. [176]Marzouk OA. Invsim algorithm for pre-computing airplane flight controls in limited-range autonomous missions, and demonstration via double-roll maneuver of Mirage III fighters. Sci Rep. 2025;15:23382. https://doi.org/10.1038/s41598-025-07639-6.
  177. [177]Struchtrup H. Thermodynamics and energy conversion. 1st ed. Berlin, Germany: Thermodynamics and Energy Conversion; Springer-Verlag; 2014.
  178. [178]Marzouk OA. Changes in fluctuation waves in coherent airflow structures with input perturbation. WSEAS Trans Signal Process. 2008;4(10):604–14.arxiv.org/abs/2410.08542
  179. [179]Poinsot T, Veynante D. Theoretical and numerical combustion. 2nd ed. Philadelphia: Edwards; 2005.
  180. [180]Warnatz J, Maas U, Dibble RW. Combustion—Physical and Chemical Fundamentals, Modeling and Simulation, Experiments, Pollutant Formation, 4th ed.; Springer Berlin Heidelberg: Berlin, Germany, 2006. https://doi.org/10.1007/978-3-540-45363-5.
  181. [181]Marzouk OA. Dataset of total emissivity for CO2, H2O, and H2O-CO2 mixtures; over a temperature range of 300–2900 K and a pressure-pathlength range of 0.01–50 Atm·m. Data Brief. 2025;59:111428. https://doi.org/10.1016/j.dib.2025.111428.
  182. [182]Kuo KK. Principles of combustion. 2nd ed. Hoboken, NJ: John Wiley; 2005.
  183. [183]Sultani an BK, Sultani an BK. Potential Flow. In: Fluid Mechanics and Turbomachinery; CRC Press: Boca Raton, Florida, USA, 2021.
  184. [184]Durst F. Potential Flows. In: Fluid Mechanics: An Introduction to the Theory of Fluid Flows; Durst, F., (Ed.); Springer: Germany, 2022; pp. 327–363. https://doi.org/10.1007/978-3-662-63915-3_11.
  185. [185]Marzouk OA. Electrical Computing Applied to Design Optimization. In: ASME 2007 International Design Engineering Technical Conferences and Computers and Information in Engineering Conference (IDETC-CIE 2007), (4–7 September 2007); ASME [American Society of Mechanical Engineers]: Las Vegas, Nevada, USA, 2009; Vol. 2, pp 995–1003. https://doi.org/10.1115/DETC2007-35502.
  186. [186]Kaushik M. Potential Flow Theory. In: Theoretical and Experimental Aerodynamics; Kaushik, M., (Ed.), Springer: Singapore, 2019; pp 107–126. https://doi.org/10.1007/978-981-13-1678-4_4.
  187. [187]Bencherif-Madani A, Pardoux É. A probabilistic formula for a Poisson equation with Neumann boundary condition. Stoch Anal Appl. 2009;27(4):739–46. https://doi.org/10.1080/0736299090297520.
  188. [188]Murti V, Valliappan S, Khalili-Naghadeh N. Time step constraints in finite element analysis of the Poisson type equation. Comput Struct. 1989;31(2):269–73. https://doi.org/10.1016/0045-7949(89)90230-7.
  189. [189]Cappelli M, Meezan N, Gascon N. Transport Physics in Hall Plasma Thrusters. In: 40th AIAA Aerospace Sciences Meeting & Exhibit, American Institute of Aeronautics and Astronautics: Reno, Nevada, USA, 2002; pp. AIAA-2002–0485. https://doi.org/10.2514/6.2002-485.
  190. [190]Pandey BP, Wardle M. Hall magnetohydrodynamics of partially ionized plasmas. Mon Not R Astron Soc. 2008;385(4):2269–78. https://doi.org/10.1111/j.1365-2966.2008.12998.x.
  191. [191]Meezan NB, Hargus WA, Cappelli MA. Anomalous electron mobility in a coaxial Hall discharge plasma. Phys Rev E. 2001;63(2):026410. https://doi.org/10.1103/PhysRevE.63.026410.
  192. [192]Levy-Nathanthson T. Studies of the generalized Ohm’s law. Physica A. 1997;241(1):166–72. https://doi.org/10.1016/S0378-4371(97)00077-0.
  193. [193]Parent B, Shneider MN, Macheret SO. Generalized Ohm’s law and potential equation in computational weakly-ionized plasmadynamics. J Comput Phys. 2011;230(4):1439–53. https://doi.org/10.1016/j.jcp.2010.11.012.
  194. [194]Knaepe B, Moreau R. Magnetohydrodynamic turbulence at low magnetic Reynolds number. Annu Rev Fluid Mech. 2008;40:25–45. https://doi.org/10.1146/annurev.fluid.39.050905.110231.
  195. [195]Lee D, Choi H. Magnetohydrodynamic turbulent flow in a channel at low magnetic Reynolds number. J Fluid Mech. 2001;439:367–94. https://doi.org/10.1017/S0022112001004621.
  196. [196]Khan O, Hoffmann K, Dietiker J-F. Validity of Low Magnetic Reynolds Number Formulation of Magnetofluiddynamics. In: 38th Plasmadynamics and Lasers Conferences; AIAA [American Institute of Aeronautics and Astronautics]: Miami, Florida, USA, 2007; p AIAA 2007–4374. https://doi.org/10.2514/6.2007-4374.
  197. [197]Oeveren SB van, Giljland D, Wheatley V, Gollan R, Jacobs P. Numerical Study of Magnetic Field Deformation for a Blunt Body with an Applied Magnetic Field During Atmospheric Entry. In: AIAA SCITECH 2024 Forum; AIAA [American Institute of Aeronautics and Astronautics]: Orlando, Florida, USA, 2024; pp AIAA 2024–1646. https://doi.org/10.2514/6.2024-1646.
  198. [198]Davidson PA. An introduction to magnetohydrodynamics. USA: Cambridge University Press; 2004.
  199. [199]Rosa RJ, Krueger CH, Shioda S. Plasmas in MHD power generation. IEEE Trans Plasma Sci. 1991;19(6):1180–90. https://doi.org/10.1109/27.125040.
  200. [200]Solmensen SV, Cuevas S, Beltrán A. Induced electric current-based formulation in computations of low magnetic Reynolds number magnetohydrodynamic flows. J Comput Phys. 2010;229(5):1558–72. https://doi.org/10.1016/j.jcp.2009.10.044.
  201. [201]Maxwell CD, Demetriades SI. Initial tests of a lightweight, self-excited MHD power generator. J Propul Power. 1986;2(5):474–80. https://doi.org/10.2514/3.22931.
  202. [202]Gupta SV. Redefining the Base Units. In: Mass Metrology: The Newly Defined Kilogram; Gupta, S. V., (Ed.), Springer International Publishing: Cham, 2019; pp. 365–384. https://doi.org/10.1007/978-3-030-12465-6_13.
  203. [203]Zhang JXJ, Hoshino K. Chapter 3—Microfluidics and Micro Total Analytical Systems. In: Molecular Sensors and Nanodevices; Zhang, J. X. J., Hoshino, K., (Eds.), William Andrew Publishing: Oxford, 2014; pp. 103–168. https://doi.org/10.1016/B978-1-4557-7631-3.00003-X.
  204. [204]NIST, [United States National Institute of Standards and Technology]. CODATA [Committee on Data for Science and Technology] Value: vacuum magnetic permeability. https://physics.nist.gov/cgi-bin/cuu/Value?mu0 (accessed 2025–02–16).
  205. [205]Alpinieri LJ. Turbulent mixing of coaxial jets. AIAA J. 1964;2(9):1560–7. https://doi.org/10.2514/3.2632.
  206. [206]Purcell EM. Life at Low Reynolds Number. In: Physics and Our World; World Scientific, 2012; pp. 47–67. https://doi.org/10.1142/9789814434973_0004.
  207. [207]Marzouk OA. Wind speed Weibull model identification in Oman, and computed normalized annual energy production (NAEP) from wind turbines based on data from weather stations. Eng Rep (Hoboken). 2025;7(3):e70089. https://doi.org/10.1002/eng2.70089.
  208. [208]Athal SM. Magnetohydrodynamic Electrical Power Generation; Unesco energy engineering series Energy engineering learning package; Wiley: Chichester, England, UK, 1995.
  209. [209]Aithal SM. Characteristics of optimum power extraction in a MHD generator with subsonic and supersonic inlets. Energy Convers Manage. 2009;50(3):765–71. https://doi.org/10.1016/j.enconman.2008.09.037.
  210. [210]Tillack MS, Morley NB. Magnetohydrodynamics. In: Standard Handbook for Electrical Engineers; Fink, D. G., Beaty, H. W., (Eds.), McGraw Hill: New York, USA, 2000; pp. 11.109–11.144.
  211. [211]Koshiba Y, Yuhara M, Ishikawa M. Two-Dimensional Analysis of Effects of Induced Magnetic Field on Generator Performance of a Large-Scale Pulsed MHD Generator. In: 35th AIAA Plasmadynamics and Lasers Conference; AIAA [American Institute of Aeronautics and Astronautics]: Portland, Oregon, USA, 2004; pp. AIAA-2004–2368. https://doi.org/10.2514/6.2004-2368.
  212. [212]Hoffmann KA, Chiang ST. Computational Fluid Dynamics—Volume 1, 4. ed., 2. print.; Engineering Education System: Wichita, Kansas, USA, 2004.
  213. [213]Marzouk O, Nayfeh A. Differential/Algebraic Wake Model Based on the Total Fluid Force and Its Direction, and the Effect of Oblique Immersed-Body Motion on ‘Type-1’ and ‘Type-2’ Lock-In. In: 47th AIAA Aerospace Sciences Meeting including The New Horizons Forum and Aerospace Exposition; AIAA [American Institute of Aeronautics and Astronautics]: Orlando, Florida, USA, 2009; p AIAA 2009–1112. https://doi.org/10.2514/6.2009-1112.
  214. [214]Fletcher CA. Computational Techniques for Fluid Dynamics—Volume I: Fundamental and General Techniques, 2nd ed.; Springer series in computational physics; Springer-Verlag: Berlin Heidelberg New York, 1991.
  215. [215]Faust E, Schlüter A, Müller H, Steinmetz F, Müller R. Multiller R. Milner R. Fluidity and Neumann boundary conditions in a Lattice Boltzmann method for elastodynamics. Comput Mech. 2024;73(2):317–39. https://doi.org/10.1007/s00466-023-02369-w.
  216. [216]Marzouk O, Nayfeh A. Physical Interpretation of the Nonlinear Phenomena in Excited Wakes. In: 46th AIAA Aerospace Sciences Meeting and Exhibit; AIAA [American Institute of Aeronautics and Astronautics]: Reno, Nevada, USA, 2008; p AIAA 2008–1304. https://doi.org/10.2514/6.2008-1304.
  217. [217]Le M. Global existence of solutions in some chemotaxis systems with sub-logistic source under nonlinear Neumann boundary conditions in 2d. Nonlinear Anal. 2024;241:113491. https://doi.org/10.1016/j.na.2024.113491.
  218. [218]Shepherd JR, Johnson CR. Hexadral mesh generation constraints. Eng Comput. 2008;24(3):195–213. https://doi.org/10.1007/s00366-008-0091-4.
  219. [219]Biswas R, Strawn RC. Tetrahedral and hexahedral mesh adaptation for CFD problems. Appl Numer Math. 1998;26(1):35–51. https://doi.org/10.1016/S0168-9274(97)00092-5.
  220. [220]Wang W, Cao Y, Okaze T. Comparison of hexahedral, tetrahedral and polyhedral cells for reproducing the wind field around an isolated building by LES. Build Environ. 2021;195:107717. https://doi.org/10.1016/j.buildenv.2021.107717.
  221. [221]Das AK, Acharyya K, Sarma S, Saha UK. Hybrid double-divergent nozzle as a novel alternative for future rocket engines. J Spacecr Rockets. 2022;59(3):761–72. https://doi.org/10.2514/1.A35207.
  222. [222]Marzouk OA, Nayfeh AH. Detailed characteristics of the resonating and non-resonating flows past a moving cylinder. In: 49th AIAA/ASME/ASCE/AHS/ASC Structures, Structural Dynamics, and Materials Conference; AIAA [American Institute of Aeronautics and Astronautics]: Schaumburg, Illinois, USA, 2008; pp. AIAA 2008–2311. https://doi.org/10.2514/6.2008-2311.
  223. [223]Lyra PRM, Almeida RC. A preliminary study on the performance of stabilized finite element CFD methods on triangular, quadrilateral and mixed unstructured meshes. Commun Numer Methods Eng. 2002;18(1):53–61. https://doi.org/10.1002/cnm.466.
  224. [224]Smith R. A PDE-Based Mesh Update Method for Moving and Deforming High Reynolds Number Meshes. In: 49th AIAA aerospace sciences meeting including the new horizons forum and aerospace exposition; AIAA [American Institute of Aeronautics and Astronautics]: Orlando, Florida, USA, 2011; pp. AIAA 2011–472. https://doi.org/10.2514/6.2011-472.
  225. [225]Koo J, Kleinstreuer C. A new thermal conductivity model for nanofluids. J Nanopart Res. 2004;6(6):577–88. https://doi.org/10.1007/s11051-004-3170-5.
  226. [226]Marzouk OA, Nayfeh AH. Simulation, analysis, and explanation of the lift suppression and Break of 2:1 force coupling due to in-line structural vibration. In: 49th AIAA/ASME/ASCE/AHS/ASC Structures, Structural Dynamics, and Materials Conference; AIAA [American Institute of Aeronautics and Astronautics]: Schaumburg, Illinois, USA, 2008; pp. AIAA 2008–2309. https://doi.org/10.2514/6.2008-2309.
  227. [227]Karataev RN. Modelling of gas streams taking account of viscosity. Meas Tech. 2005;48(2):171–4. https://doi.org/10.1007/s11018-005-0118-9.
  228. [228]Hardiantо T, Sakamoto N, Harada N. Three-dimensional flow analysis in a Faraday-type MHD generator. IEEE Trans Ind Appl. 2008;44(4):1116–23. https://doi.org/10.1109/TIA.2008.926200.
  229. [229]SciPy. scipy.optimize.curve_fit. https://docs.scipy.org/doc/scipy/reference/generated/scipy.optimize.curve_fit.html (accessed 2025–02–15).
  230. [230]SciPy. Optimization and root finding (scipy.optimize) — SciPy v1.15.1 Manual. https://docs.scipy.org/doc/scipy/reference/optimize.html#module-scipy.optimize (accessed 2025–02–15).
  231. [231]Himawan M, Sadrawi M. Development of long QT syndrome detection using SciPy. Indones J Life Sci. 2023. https://doi.org/10.54250/ijls.v5i02.178.
  232. [232]Foust HC III. Thermodynamics, gas dynamics, and combustion. Cham: Springer International Publishing; 2022. https://doi.org/10.1007/978-3-030-87387-5.
  233. [233]Kumar S. Problems and solutions in thermal engineering: with multiple-choice type questions. Cham: Springer International Publishing; 2023. https://doi.org/10.1007/978-3-031-10584-5.
  234. [234]Marzouk OA. Coupled differential-algebraic equations framework for modeling six-degree-of-freedom flight dynamics of asymmetric fixed-wing aircraft. Int J Appl Adv Sci. 2025;12(1):30–51. https://doi.org/10.21833/ijaas.2025.01.004.
  235. [235]Ding H, Dong Y, Zhang Y, Wen C, Yang Y. Performance of supercritical carbon dioxide (SCO₂) centrifugal compressors in the Brayton cycle considering non-equilibrium condensation and exergy efficiency. Energy Convers Manage. 2024;299:117849. https://doi.org/10.1016/j.enconman.2023.117849.
  236. [236]Kirkpatrick AT. Fluid Flow in Refrigeration and Air Conditioning Systems. In: Introduction to Refrigeration and Air Conditioning Systems: Theory and Applications; Kirkpatrick, A. T., (Ed.), Springer International Publishing: Cham, 2023; pp 65–89. https://doi.org/10.1007/978-3-031-16776-8_4.
  237. [237]Darbandi M, Zakyani M, Schneider G. Evaluation of Different K-Omega and k-Epsilon Turbulence Models in a New Curvilinear Formulation. In: 17th AIAA Computational Fluid Dynamics Conference; American Institute of Aeronautics and Astronautics: Toronto, Ontario, Canada, 2005; pp. AIAA 2005–5101. https://doi.org/10.2514/6.2005-5101.
  238. [238]Marzouk OA, Huckaby ED. Simulation of a swirling gas-particle flow using different k-epsilon models and particle-parcel relationships. Eng Lett. 2010;18(1).
  239. [239]Kurganov A, Petrova G. Central schemes and contact discontinuities. ESAIM Math Model Num Anal. 2000;34(6):1259–75. https://doi.org/10.1051/m2an:2000126.
  240. [240]Kurganov A, Tadmor E. New high-resolution central schemes for nonlinear conservation laws and convection-diffusion equations. J Comput Phys. 2000;160(1):241–82. https://doi.org/10.1006/jcph.2000.6459.
  241. [241]Marzouk OA. The sod gasdynamics problem as an example of the flux construction in the finite volume method. Sci Afr. 2020; e00573. https://doi.org/10.1016/j.sciaf.2020.e00573.
  242. [242]Kurganov A, Tadmor E. New high-resolution semi-discrete central schemes for Hamilton-Jacobi equations. J Comput Phys. 2000;160(2):720–42. https://doi.org/10.1006/jcph.2000.6485.
  243. [243]Sparrow EM, Gregg JL. Heat transfer from a rotating disk to fluids of any Prandtl number. J Heat Transfer. 1959;81(3):249–51. https://doi.org/10.1115/1.4008195.
  244. [244]Li D. Turbulent prandtl number in the atmospheric boundary layer—Where are we now? Atmos Res. 2019;216:86–105. https://doi.org/10.1016/j.atmosres.2018.09.015.
  245. [245]OpenCFD. OpenFOAM/User Guide - Implementation details (Matrix structure). https://www.openfoam.com/documentation/guides/v2112/doc/guide-solvers.html (accessed 2025–06–14).
  246. [246]OpenCFD. OpenFOAM/User Guide - Linear equation solvers. https://www.openfoam.com/documentation/guides/v2112/doc/guide-solvers.html (accessed 2025–06–14).
  247. [247]OpenCFD. OpenFOAM/User Guide - Gauss Seidel Smoother. https://www.openfoam.com/documentation/guides/latest/doc/guide-solvers-smoother-gauss-seidel.html (accessed 2025–06–14).
  248. [248]OpenCFD. Documentation/6.3 Solution and algorithm control. https://www.openfoam.com/documentation/user-guide/6-solving/6.3-solution-and-algorithm-control (accessed 2025–02–04).
  249. [249]OpenCFD. OpenFOAM/User Guide - DILU preconditioner. https://www.openfoam.com/documentation/guides/v2112/doc/guide-solvers-cg-preconditioner-dilu.html (accessed 2025–06–14).
  250. [250]Howell GW, Baboulin M. LU preconditioning for Overdetermined Sparse Least Squares Problems. In: Parallel Processing and Applied Mathematics; Wyrzykowski, R., Deelman, E., Dongarra, J., Karczewski, K., Kitowski, J., Wiatr, R., (Eds.), Springer International Publishing: Cham, 2016; pp 128–137. https://doi.org/10.1007/978-3-319-32649-3_13.
  251. [251]Marzouk OA, Huckaby ED. A comparative study of eight finite-rate chemistry kinetics for CO/H₂ combustion. Eng Appl Comput Fluid Mech. 2010;4(3):331–56. https://doi.org/10.1080/19942060.2010.1015322.
  252. [252]Oberkampf WL, Trucano TG. Verification and validation in computational fluid dynamics. Prog Aerosp Sci. 2002;38(3):209–72. https://doi.org/10.1016/S0376-0421(02)00005-2.
  253. [253]Wüthrich B. Simulation and Validation of Compressible Flow in Nozzle Geometries and Validation of OpenFOAM for This Application. Master Thesis, Institute of Fluid Dynamics, ETH [Swiss Federal Institute of Technology Zurich], Zürich, Switzerland, 2007. https://doi.org/10.3929/ethz-a-00557219 (accessed 2025–02–16).
  254. [254]Ishikawa M, Yuhara M, Fujino T. Three-dimensional computation of magnetohydrodynamics in a weakly ionized plasma with strong MHD interaction. J Mater Process Technol. 2007;181(1–3):254–9. https://doi.org/10.1016/j.jmatprotec.2006.03.032.
  255. [255]Ayleso AO, Kahn MTE, Raji AK. Computational Fluid Domain Simulation of MHD Flow of an Ionised Gas inside a Rectangular Duct (August 2016). In: 2016 International Conference on the Industrial and Commercial Use of Energy (ICUE); 2016; pp. 84–91.
  256. [256]Swallom DW, Goldfarb VM, Gibbs JS, Sadovnik I, Zeigarnik VI, Kuzmin RK, Aitov NL, Okunev VI, Novikov VA, Rickman VI, Blokh AG, Pisakin AV, Egorushkin PN, Tkachenko BG, Babakov JP, Olson AM, Anderson RE, Fedun MA, Hill GR. Results from the Pamir-3U Pulsed Portable MHD Power System Program. In: 12th International Conference on MHD Electrical Power Generation; Yokohama, Japan, 1996; Vol. 1, pp. 186–195.
  257. [257]Velikhov EP, Pismenny VD, Matveenko OG, Panchenko VP, Yakushev AA, Pisakin AV, Blokh AG, Tkachenko BG, Sergienko NM, Zhukov BB, Zheglov EF, Babakov YP, Polyakov VA, Glukhikh VA, Manukyan GS, Krylov VA, Vesnin VA, Parkhomenko VA, Sukharev EM, Malashko YI. Pulsed MHD Power System “Sakhalin”—The World Largest Solid Propellant Fueled MHD Generator of 500MWe Electric Power Output. In: 13th International Conference on MHD Electrical Power Generation and High Temperature Technologies; Beijing, China, 1999; Vol. 2, pp. 387–398.
  258. [258]Panchenko VP. Preliminary Analysis of the “Sakhalin” World Largest Pulsed MHD Generator. In 33rd Plasmadynamics and Lasers Conference; AIAA [American Institute of Aeronautics and Astronautics]: Maui, Hawaii, USA, 2002; pp. AIAA–2002–2147. https://doi.org/10.2514/6.2002-2147.
  259. [259]Makinde OD, Sandeep N, Ajayi TM, Animasahun II. Numerical exploration of heat transfer and Lorentz force effects on the flow of MHD Casson fluid over an upper horizontal surface of a thermally stratified smelting surface of a paraboloid of revolution. Int J Nonlinear Sci Numer Simul. 2018;19(2):93–106. https://doi.org/10.1515/ijnsns-2016-0087.
  260. [260]Khrapak SA, Khrapak AG. On the conductivity of moderately non-ideal completely ionized plasma. Results Phys. 2020;17:103163. https://doi.org/10.1016/j.rinp.2020.103163.
  261. [261]Smirnov BM. Transport Processes in Gas Discharge Plasma. In Theory of Gas Discharge Plasma; Smirnov, B. M., (Ed.), Springer International Publishing: Cham, 2015; pp. 151–196. https://doi.org/10.1007/978-3-319-01165-3_7.
  262. [262]AML, [Ames Aeronautical Laboratory]. Equations, Tables, and Charts for Compressible Flow; Technical Report NACA-TR-1135; NACA [United States National Advisory Committee for Aeronautics]: Moffett Field, California, USA, 1953; pp 612–681. https://ntrs.nasa.gov/api/citations/19930091059/downloads/19930091059.pdf (accessed 2025–02–17).
  263. [263]Moroz L, Burlaka M, Frolov B, Dzyenko I. Supersonic convergent-divergent vaned nozzles design algorithm and respective discharge coefficient model. Am Soc Mech Eng Digit Collect. 2024. https://doi.org/10.1115/GT2024-125893.
  264. [264]Puzach SV. Effect of supersonic diffuser geometry on operation conditions. Exp Therm Fluid Sci. 1992;5(1):124–8. https://doi.org/10.1016/0894-1777(92)90061-9.
  265. [265]Marzouk OA. Subcritical and supercritical Rankine steam cycles, under elevated temperatures up to 900°C and absolute pressures up to 400 bara. Adv Mech Eng. 2024;16(1):16878132231121064. https://doi.org/10.1177/16878132231121065.
  266. [266]Marzouk OA. Condenser pressure influence on ideal steam Rankine power vapor cycle using the Python extension package Cantera for thermodynamics. Eng Technol Appl Sci Res. 2024;14(3):14069–78. https://doi.org/10.48084/etasr.7277.
  267. [267]Pukhtyar DL. Numerical analysis of the electromagnetic fields induced by wave motions in the North part of the Aegean Sea. Phys Oceanogr. 2003;13(4):223–32. https://doi.org/10.1023/A:1025802100838.
  268. [268]Shankland TJ, Prevorneanu J, Poirier J-P. Electrical conductivity of the Earth’s Lower Mantle. Nature. 1993;366(6454):453–5. https://doi.org/10.1038/366453a0.
  269. [269]Wang G, Yang F, Wu K, Ma Y, Peng C, Liu T, et al. Estimation of the dissipation rate of turbulent kinetic energy: a review. Chem Eng Sci. 2021;229:116133. https://doi.org/10.1016/j.ces.2020.116133.

Paper details

vlnc:W_egkbymdd
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents