WorksPhysics and Astronomy
Photo-switchable nanoripples in Ti3C2Tx MXene
Abstract
MXenes are two-dimensional materials with a rich set of remarkable chemical and electromagnetic properties, the latter including saturable absorption and intense surface plasmon resonances. To fully harness the functionality of MXenes for applications in optics, electronics and sensing, it is important to understand the interaction of light with MXenes on atomic and femtosecond dimensions. Here, we use ultrafast electron diffraction and high-resolution electron microscopy to investigate the laser-induced structural dynamics of Ti3C2Tx nanosheets. We find an exceptionally fast lattice response with an electron-phonon coupling time of 230 femtoseconds. Repetitive femtosecond laser excitation transforms Ti3C2Tx through a structural transition into a metamaterial with deeply sub-wavelength nanoripples that are aligned with the laser polarization. By a further laser illumination, the material is reversibly photo-switchable between a flat and rippled morphology. The resulting nanostructured MXene metamaterial with directional nanoripples is expected to exhibit an anisotropic optical and electronic response as well as an enhanced chemical activity that can be switched on and off by light.
*Authors to whom correspondence should be addressed:
Figure 1.
Main text
MXenes are a large and rapidly-expanding family of two-dimensional transition metal carbides, nitrides and carbonitrides in form of few-atom-thick nanosheets. The general chemical formula is , where = 1-3, is an early transition metal, is carbon or nitrogen and is a surface termination group, such as O, OH or F.[1, 2] MXenes exhibit a plethora of unique chemical, mechanical, optical and electronic properties that find applications in chemical and mechanical sensing, energy storage, electronics and nonlinear optics, to name a few.[3] Insight from numerous studies has paved the way to rationalize, predict, engineer and exploit those properties of MXenes for various applications[3, 4, 5, 6, 7]. However, MXenes with a controlled nanostructure, for example with laser-induced periodic surface structures (LIPSS)[8], are currently not available, despite potential advantages of such materials for photocatalysis, antibiotic activity, charge storage or surface-enhanced Raman scattering.[9, 10, 11, 12, 13, 14]
Among the broad class of available MXenes, has been synthesized first[15] and is to date the most widely investigated material, both theoretically and experimentally. The 2D nature and metallic conductivity of give rise to peculiar optical properties and light-driven phenomena. For example, is highly effective in shielding electromagnetic interference[16] and its wide optical absorption spectrum allows for efficient light-to-heat conversion.[17] Irradiation in ambient air or water solution has been shown to accelerate degradation of into and amorphous titanium carbide in the laser-treated regions,[18, 19] and focused femtosecond laser beams can thereby create flexible electronic circuits.[20, 21] At high light intensity, exhibits broadband saturable absorption that enables effective laser mode-locking and other nonlinear photonics applications.[22, 23, 24] The majority of such effects, however, are currently discussed from a rather phenomenological and applied perspective, and a time-resolved, atomic-scale description of light-matter interaction in MXenes is not yet fully developed.
Here we use ultrafast electron diffraction as a direct probe of structural dynamics in laser-excited with femtosecond and atomic resolutions in time and space,[25, 26] complemented by an atomic-resolution transmission electron microscopy study of the laser-processed materials. We find that exhibits a very fast, 230-fs lattice response to laser excitation. Repetitive laser irradiation induces 20-nm periodic ripples that are aligned with the electric field of the laser light. The nanoripples are reversibly flattened out during further laser irradiation, rendering this morphological transformation photo-switchable.
Figure 1 (PDF p. 4). (a) Experimental layout of the ultrafast electron diffraction experiments with terahertz electron compression. A laser source synchronously drives electron pulse generation via its second harmonic (SHG, 515 nm wavelength), produces THz pulses for compression and streaking, and provides 55-fs pump pulses for sample excitation. Electron pulses at an energy of 70 keV and with about 8 electrons/pulse are focused with a magnetic lens (ML) and compressed down to a pulse duration of 75 fs with a THz pulse on an aluminum foil (black). A bow-tie resonator (not depicted) provides temporal characterization of the pulses via electron streaking. A free-standing film of on a copper mesh is pumped by a near-infrared laser pulse at 1028 nm wavelength. (b) THz streaking of the compressed electron pulse reveals a slope of 0.17 pixels/fs (black line) and an electron pulse duration of 75 fs. (c) MXene diffraction pattern. Two intense diffraction rings are observed at 0.39 and 0.67 , corresponding to (100) and (110) indexes. (d) Ultrafast Debye-Waller effect in MXene. The intensity drop of the (110) diffraction ring occurs within 230 fs. Black dots show experimental data; blue curve shows a fit with a response function , = 230 fs.
Results
Femtosecond electron diffraction
Figure 1a depicts our femtosecond electron diffraction experiment.[27, 28] Ultrashort electron pulses without space charge effects[29] are generated at a central energy of 70 keV by two-photon laser photoemission[30] and subsequent electrostatic acceleration. Single-cycle terahertz radiation is used to compress the electron pulses[27] down to a duration of 75 fs. Figure 1b shows terahertz streaking data from which we directly measure the electron pulse duration in the experiment. The specimen is a freestanding film of flakes that are prepared by chemical exfoliation (Methods) and then deposited onto a support grid with a mesh spacing of 300 m. The sample is excited by femtosecond laser pulses with a center wavelength of 1028 nm and a pulse duration of 55 fs, yielding in total a sub-100-fs time resolution of our ultrafast electron diffraction experiment.
Figure 1c shows the static electron diffraction pattern of the flakes as observed with our femtosecond pulses. The two most prominent rings correspond to Bragg indices of (100) and (110) with reciprocal lattice vectors of 0.39 Å and 0.67 Å, respectively. Slight deviations from a circular shape are due to distortions in the large magnetic lenses after the electron-sample interaction. The presence of mainly (100) and (110) diffraction rings, their sharpness and high intensity indicate that all flakes are lying flat on the support mesh with the preferred orientation along the -axis. The intensity of the both diffraction rings shows a homogeneous azimuthal distribution, indicating random rotational orientation of the stacked 2D flakes.
Femtosecond laser excitation with a fluence of 0.9 mJ/cm induces a decrease of the measured diffraction intensities in the rings as a consequence of the ultrafast Debye-Waller effect. The inset of Figure 1d shows the difference of the diffraction patterns before and after time zero, exhibiting an isotropic intensity drop of about 0.8%. Ring diameters and widths remain constant within the sensitivity of our experiment. Figure 1d shows the integrated electron counts in the (110) diffraction ring as a function of the pump-probe delay. We determine the response time from a fit with an exponential response function (blue solid line) and obtain an electron-phonon coupling rate of 230105 fs at 95% confidence. We see no further dynamics of the diffraction pattern in the following 30 picoseconds.
Field-induced nanoripple formation
At a higher laser fluence, above 1 , we observe a permanent structural transition that manifests as new diffraction arcs that appear at an inverse atomic distance of 0.47 and break the azimuthal symmetry of the ring pattern. Figure 2b shows such a diffraction pattern, obtained by illuminating the specimen with s-polarized femtosecond laser pulses at an incidence angle of 25° with a peak fluence of 1.6 for 10 seconds and then letting the sample relax back to room temperature. Notably, the broken symmetry aligns with the electric field direction of the femtosecond laser (Figure 2b, magenta arrows). Figure 2c shows the diffraction pattern of a fresh sample that is illuminated with femtosecond laser pulses of perpendicular polarization. We see a 90° rotation of the symmetry-breaking additional diffraction arcs. Rotation of the polarization by 45° produces a 45° arc rotation. Once processed, the samples retain their arc orientation and cannot be switched into other arc orientations by further illumination attempts.
Figure 2. Laser-induced symmetry breaking. (a) Electron diffraction pattern from pristine . (b), (c) Electron diffraction after laser processing with orthogonal polarizations (magenta arrows). Data is taken at room temperature with the laser off. (d) Electron diffraction from a laser-processed sample while the laser in on. The processing is irreversible (black arrows with red crosses) but the switching is reversible (black arrows).
To assess quantitatively the transition threshold, that is, the minimum optical power that is required to produce the arcs, we gradually increase the laser fluence that impinges on a fresh specimen. After application of each laser fluence, we let the specimen relax to room temperature and then measure the intensity of the diffraction rings. We find that the symmetry-breaking arcs appear at a laser fluence of , corresponding to a laser power of , but not at lower laser powers even for longer illumination times (Figure S3). The same experiments at twice the laser repetition rate and twice the average power produce the same per-pulse fluence threshold of ca. . This result indicates that the transformation is non-thermal but must be directly related to the high peak intensity of the femtosecond pulses. From sample to sample, the fluence threshold varies by about . An increase of the laser fluence to ca. of the transition threshold initiates a gradual evaporation of the flakes, observed as an irreversible decrease of electron intensity in all the diffraction rings (Figure S3).
(a)
(b)
Figure S3. (a) Electron count in the diffraction rings and arcs of a room-temperature TiCT, exposed to a certain maximum fluence (horizontal axis). Green-shaded area shows the photoswitching range. Red-shaded area indicates the irreversible range with gradual evaporation of the sample. (b) Photoswitching dynamics, corresponding to the green area of panel (a). The differential image of the diffraction pattern is “laser on” minus “laser off”.
While a laser-processed specimen is under laser illumination above the formation threshold but below the damage threshold, the symmetry-breaking arcs diminish and reduce their intensity almost to zero (Figure 2d). At the same time, the intensity of the ring increases to a higher intensity than before (Figure S3), indicating a higher degree of orientation with respect to the axis. When switching the light off, the electron diffraction returns to the original symmetry-broken pattern that was created by the initial processing. More than 50 reversible phase changes are observed without a measurable degradation of the specimen (Figure S3).
Selected-area electron diffraction (SAED) and high-resolution transmission electron microscopy (HRTEM)
In order to understand the laser-induced structural transformation, we report a transmission electron microscopy (TEM) analysis of the pristine and the laser-beam processed films. Figure 3a and Figure 3b show selected-area electron diffraction (SAED) patterns of the pristine and the laser-processed films, respectively. The probed area has a diameter of ca. . Both diffraction patterns reproduce the femtosecond results of Figure 2. The pattern of the fresh sample is dominated by and rings, reflecting the preferential orientation of the two-dimensional films with alignment to the axis (see above). In contrast to the fresh material, the SAED pattern of the laser-processed films contains additional, relatively intense diffraction arcs near the ring, as already seen in the femtosecond diffraction data (Figure 2). Notably, thermal (non-optical) heating up to with subsequent cooling does not produce any arcs (Figure S4). Rotational averaging of the two-dimensional (2D) diffraction pattern is used to generate one-dimensional (1D) diffraction data for further analysis (Figure 3d). A comparison of the two 1D diffraction data shows the re-distribution of intensity and growth of the arc feature in the laser-processed sample. The decrease of the and the peak intensities indicates a reduced effect of the preferential orientation as compared to the pristine film.
Figure 3. TEM analysis of pristine and laser-processed films. (a) SAED pattern of the pristine film with a tilt angle relative to the e-beam. (b) SAED pattern of the laser-processed material. (c) SAED pattern of the pristine sample recorded at tilt. (d) Comparison of the 1D SAED data of the pristine (blue) and laser-processed (magenta) materials. (e) Comparison of the 1D SAED data of the laser-processed (magenta) and the pristine (blue) films at tilt. (f) Illustration of the planes, , in a tilted MXene stack.
Figure S4. SAED patterns during in-situ TEM thermal heating of pristine TiCT. (a) Initial diffraction pattern at room temperature. (b) Diffraction pattern obtained at room temperature after intermediate thermal heating up to 500°C. (c) Diffraction pattern at 500°C. Neither of these patterns shows any indications of arc formation.
Additional SAED patterns are recorded as a function of tilt angle of the film with respect to the incident electron beam (Figure S2). We observe that the intensity of the (110) peak decreases while the intensity of diffraction arcs grows with increasing the tilt angle. A comparison of the SAED patterns of the laser-processed and pristine films tilted by shows similarities in the diffraction intensities (Figure 3b, Figure 3c, Figure 3e). Therefore, both materials possess a similar crystallographic long-range order. The new diffraction arcs can be assigned to the diffraction planes (Figure 3f, magenta lines). The orientation of the planes with respect to the crystallographic -axis inside the MXene structure is shown in Figure 3f. A similar arc formation effect is observed for example in highly-ordered pyroelectric graphite under a 20-degree tilt[31] or in thin-films with a lamellar or fibrous texture.[32]
Figure S2. Series of SAED patterns of as a function of tilt angle (see the inset for color codes and angles used).
Since the MXene films consist of stacks of 2D nanosheets that do not feature a high degree of crystallographic order in the stacking direction, we use the atomic electron pair distribution function (ePDF) for a quantitative analysis of the local atomic structures of pristine and laser-processed films. Figure 4a shows the results in form of reduced structure factors, F(Q). We see that the data from the pristine (blue) and laser-processed specimen (magenta) are very similar (Figure 4a). In Figure 4b, the corresponding ePDF data (G(r) functions) are presented as light grey circles while the blue and magenta curves correspond to the refinements of the pristine film and a laser-processed specimen, respectively, using a model based on the reported structure.[33] The black lines denote the residuals of the fits. While the structure refinement of the pristine film (blue) provides an acceptable fit to the data with an agreement factor , the ePDF fit of the laser-processed MXene (magenta) shows a poorer agreement (, Figure 4b). However, the fit of a laser-processed specimen is reasonable at larger atomic distances above ca. , indicating a good match to the structure in the medium-range order. A clear misfit is only observed in the region of low interatomic distances (compare the top and bottom black residual data in Figure 4b). There, the laser-processed specimen features an additional peak at an interatomic distance of ca. that cannot be accounted for by the reported structural model.[34] The peak is most likely due to shortened Ti-O/F/C bond(s) after the laser exposure (the enlarged region in Figure 4c). This relatively short bond length is characteristic for [TiO4] tetrahedra that are found in some titanates (for example in CsAlTiO4, ICSD: 65707, Ti–O bond length is ). Therefore, it appears likely that a loss or reconfiguration of terminal groups due to the laser treatment is responsible for the appearance of this additional peak.
Figure 4. ePDF analysis. (a) Reduced structure factors, , of the pristine material, recorded at −15° tilt angle (blue) and the laser-processed material at no tilt (magenta). (b) ePDF fits. Light gray circles correspond to the measured data, magenta and blue solid lines are the refined PDFs, and the black solid lines are the residuals. (c) Zoom into the low- ePDF region, showing a characteristic double peak of the Ti- distances of the laser-processed sample (magenta).
In addition, the fitted structure has a parameter of about , which corresponds to an interlayer spacing of about between the nanosheets.[33] X-ray diffraction (XRD) data of our films (Figure S1) indicates a larger parameter of ca. , corresponding to an interlayer spacing of about . However, the interlayer distance in MXenes depends on the nature of the species (solvent molecules and Li salts used during the material synthesis) that are intercalated in between the nanosheets and also on the drying temperature.[35] We argue that the removal of intercalated water in the high vacuum of our experiments ( mbar) and/or the electron beam irradiation most likely account for the measured decrease of interlayer distance.
Figure S1. X-ray diffraction pattern (XRD) of the pristine MXene material .
Together, the SAED and ePDF analysis of the pristine and the laser-processed materials reveal that the medium-range and long-range atomic order of the structure is not affected by the laser exposure. The laser processing induces a morphological restructuring of nanosheets that diminishes the preferential orientation and results in an SAED pattern that is comparable to the one of the pristine material reordered at −15° tilt angle (compare Figure 3b and Figure 3c). In addition, the laser irradiation alters the short-range order and brings about a new atomic distance at ca. 1.7 Å.
High-resolution transmission electron microscopy (HRTEM)
To assess the changes between the pristine material and the laser-processed material at the atomic level, we use high-resolution transmission electron microscopy (HRTEM). Figure 5a shows the HRTEM image and the corresponding Fourier transform (FT) pattern of the pristine material, revealing single-crystalline nanosheets that are oriented along the zone axis. The FT pattern of the real-space image (Figure 5b) of the laser-processed displays the arcs (Figure 5b, inset). In order to reveal the atomic-scale origin of the diffraction arcs in real space, we calculate the inverse FT image of only the arcs in the computed diffraction pattern. The results are depicted in Figure 5c and highlight only those parts of the lattice that contribute to the creation of the anisotropic diffraction arcs. We see atomic fringes in form of a pattern with a regular periodicity of about 20 Å. This result means that the laser treatment induces undulations (i.e. ripples) of the MXene sheets with a specific periodicity that is much smaller than the laser wavelength (1028 nm). As a result, the originally flat morphology of nanosheets on the nanoscale[15] transforms to a regularly rippled hill-and-valley morphology, thereby allowing the reflections to appear in the SAED patterns (Figure 3b) and in the femtosecond data of Figure 1c.
Figure 5. Transmission electron microscopy analysis. (a) HRTEM micrographs of the pristine material. (b) HRTEM micrographs of the laser-processed nanosheets. Fourier-transform (FT) patterns are shown as insets. (c) Filtered real-space image obtained by selective inverse Fourier transform of the arcs marked by magenta ovals in the FT pattern of the HRTEM micrograph in panel (b).
DISCUSSION
We first discuss the femtosecond results and afterwards the ripple formation. The observed ultrafast lattice response time of 230 fs is significantly shorter than the rate of several picoseconds that has been suggested before.[36, 37, 38, 39] In particular, optical pump-probe investigations of the photo-induced dynamics in have previously estimated an electronic response of 100-400 fs and a subsequent lattice heating within only 1-4 ps.[36, 37, 38, 39] Our data overturns this picture and directly shows by real-space observation of the atomic dynamics that the lattice becomes hot within merely 230 fs after laser excitation. This value is, to our knowledge, the fastest reported Debye-Waller response of a simple crystal without a phase transition, i.e. excluding the sub-100-fs decay of the Peierls distortion in antimony[40] and the charge-density waves in bismuth[41]. The ultrafast electron-phonon coupling of our MXenes is a signature of an efficient energy and momentum transfer between the electronic band structure and the phonons, similar to the strongly coupled in-plane phonons in graphite[42, 43] and the efficient plasmon-phonon coupling in graphene.[44] The ultrafast decay of optical excitations into phonons in MXenes might therefore be related to the highly efficient light-to-heat conversion of this material.[17]
The discovered formation of nanoripples in our sheets has features and excitation conditions that relate to the laser-induced periodic surface structures (LIPSS) that can be formed on the surface of metals and semiconductors under near-breakdown femtosecond irradiation.[8] For example, sub-wavelength structures on titanium can become as small as 50 nm, as well as aligned with the laser electric field.[45] An elusive feature of this effect is the short wavelength of the fabricated nanostructures that can have dimension much smaller than the optical wavelength. Also in our sheets, the periodicity is 50 times smaller than the wavelength. It has been hypothesized that the extremely small modulation period of deep-subwavelength nanoripples in semiconductors and metals is caused by localized surface plasmon resonances under femtosecond nonequilibrium.[46] Our results support this inference. The femtosecond lattice response shows no anisotropy (Figure 1d, inset), suggesting that nanoripple formation is a multi-pulse effect. Yet the final nanoripple orientation is stable against a change of laser polarization, indicating the self-sustaining nature of nanoripples. The threshold character of ripple formation further signifies the role of optical nonlinearities in the process. We suggest that the plasmonic properties of [47, 48] and its extremely fast lattice reaction time (Figure 1) combine to play an important role in the observed sub-wavelength nanorippling. MXenes are plasmonic materials[47] in the near-infrared region, but behavior of MXenes is different from classical plasmonic metals[48] in that the sheets are isolated and behave like independent structures. The dependence of the laser threshold value on a particular sample spot ( mJ/cm) indicates the role of local optical resonances as triggers for the necessary symmetry breaking and self-organization.
The ripples observed in Figure 5c are similar to the topological defects in graphene, where the presence of pentagonal units in hexagonal graphene lattice induces buckling.[49] Based on this analogy and in agreement with the ePDF analysis, where the additional low- component of the Ti-O/F/C atomic distance has been observed, we conclude that our laser irradiation of an initially flat MXene sheet induces ripples and regular defects that are associated with low-coordinated Ti atoms due to the curvature of the ripples that are formed. There is no laser-induced crystallization or bond-interchange[50, 51] nor a phase transition or a chemical reaction, in agreement with theoretical reports that predict that the ground state is thermodynamically stable.[52, 53] Interestingly, our diffraction data indicates that we produce nano-ripples throughout the entire stack of sheets, in contrast to a mere surface-layer modification typically observed in LIPSS. In other words, we modify a bulk stack of nanosheets.
Conclusion
In conclusion, MXene has an ultrafast electron-phonon coupling rate of 230 fs which is by a factor of about ten faster than hitherto supposed. Femtosecond laser treatment of flat nanosheets induces a regular hill- and valley morphology in form of nanoripples at a specific and well-defined periodicity that is about a factor of 50 smaller than the laser wavelength. Consequently, Bragg reflections show up in electron diffraction. The orientation of the nanoripples is controlled by the laser polarization and the formation is therefore in part a field effect. A once processed specimen can repeatedly be switched forth and back between a flat and rippled morphology by illumination with laser light. This reversible nanorippling is expected to further enhance the performance of MXenes for various applications.
Methods
Sample Preparation
ink (colloidal solution in water, ca. 3 mg ml) is prepared after chemical exfoliation of the respective MAX precursor, i.e. , in an aqueous mixture of LiF and HCl, following the reported protocol.[35] This ink is drop-casted onto copper TEM grids with 170-μm windows, which forms free-standing thin films after evaporation of the solvent. In few-electron diffraction, the sample must be thin enough to be electron-transparent but thick enough to produce efficient diffraction. To achieve an optimal thickness (as determined experimentally), the concentration of the ink is adjusted using distilled water before drop casting (ca. 1 mg ml).
Experimental setup
The ultrafast electron diffraction experiments are carried out on a femtosecond electron beamline (Figure 1a) described in detail previously.[27, 28] A laser system with pulse repetition rate of 25 kHz (Pharos, Light Conversion Inc.), center wavelength of 1028 nm and 270-fs pulse duration drives the electron pulse generation, the terahertz (THz) compression, the THz streaking and the sample excitation. A symmetric layout of THz generation for the compression and streaking stages allows to minimize the timing jitter of THz generation. The electron pulses are produced via two-photon photoemission from a back-illuminated gold cathode.[30] A compact electron gun[54] accelerates the electrons to 70 keV, minimizing the influence of vacuum dispersion on the electron pulse duration.[29] We avoid space-charge effects by using less than 8 electrons per pulse.[29] The electron beam is focused with a magnetic lens, and a single-cycle terahertz pulse compresses the electrons down to 75 fs (full width at maximum) on aluminum foil.[27] The electron pulse duration is characterized via THz streaking in a bow-tie resonator[27], providing a temporal resolution of 0.17 pixels/fs (Figure 1b). Streaking broadens the electron beam from 24.8 pixels to 27.4 pixels (full width at maximum), yielding an electron pulse duration estimate of 75 fs full width at maximum or 44 fs full width at half maximum.
The near-infrared (NIR) pump pulses are produced via double-stage second-harmonic non-phase-matched broadening in self-defocusing medium.[55, 56, 57] A frequency-resolved optical gating measurement (FROG) yields 55-fs pulses, accounting for the dispersion of the entrance window into the vacuum chamber. Laser fluence and intensity are determined by imaging the actual beam profile in the focus in the vacuum chamber onto a CMOS camera with no assumptions on the beam shape. If a Gaussian fit of the beam profile is applied, it yields a diameter of 208 μm in the focus (full width at maximum). The optical beam is incident on the front surface of the MXene-covered copper support grid. The electron beam is focused with a magnetic lens to a size at the sample of (full width at maximum), measured with a knife-edge scan and the electron camera.
The diffraction pattern is focused and magnified onto the sensor (TemCam F416, TVIPS GmbH) with a second magnetic lens in order to improve the signal-to-noise in the weak diffraction rings while avoiding camera saturation by the zero-order Bragg spot. Astigmatism of the magnetic lens causes a slight distortion of the diffraction rings into ellipses. We calibrate the image rotation and the diffraction angles with a crystalline silicon sample. In the femtosecond pump-probe experiments, fluctuations of pulsed electron current are eliminated by normalizing each evaluated diffraction intensity to the intensity of the direct beam (000 order). The incident average laser power is , the pulse energy is , the peak intensity is and the fluence is .
The transmission electron microscope is a double Cs-corrected (TEM&STEM) scanning transmission electron microscope (JEM-ARM300F Grand ARM, JEOL Inc.) that was operated at an electron energy of . For electron microscopy, samples were prepared by drop deposition of colloidal solution onto a copper grid of 200 mesh coated with lacy carbon. All electron diffraction patterns were recorded on a charge-coupled device camera (One View, Gatan Inc.). Azimuthal integration of two-dimensional electron diffraction patterns and their conversion into the reduced pair-distribution function was done using the freely available eRDFanalyzer software. [58] Structural refinement of the obtained ePDFs is made with the PDFgui software.[59]
A cross-grating sample serves for calibrating the camera length and instrument resolution parameters and . The refined values of () and () are fixed during refinement. The camera length is set to reach a reasonable Q value of ca. .
ASSOCIATED CONTENT
Supporting Information. Additional XRD and SAED characterization data, in situ heating and laser switching experiments.
AUTHOR INFORMATION
Corresponding Authors
Mikhail Volkov - University of Konstanz, 78464 Konstanz, Germany; https://orcid.org/0000-0003-1594-8542; Email: [email protected]
Elena Willinger - ETH Zürich, 8092 Switzerland; https://orcid.org/0000-0001-5117-923X; Email: [email protected]
Author Contributions
The manuscript was written through contributions of all authors. All authors have given approval to the final version of the manuscript.
Funding Sources
We acknowledge the European Research Council (ERC) under the European Union's Horizon 2020 research and innovation program (grant agreement No. 819573) for partial funding of this work.
Acknowledgement
The authors thank F. Krausz for laboratory infrastructure and the Scientific Centre for Optical and Electron Microscopy (ScopeM) of ETH Zürich for providing access to electron microscopes.
Photo-switchable nanoripples in TiC MXene
Mikhail Volkov; Elena Willinger; Denis A. Kuznetsov; Christoph R. Müller; Alexey Fedorov; Peter Baum
Supporting Information for
Authors to whom correspondence should be addressed:
X-ray diffraction characterization (XRD)
The XRD pattern of the initial MXene material is shown in Figure S1. The characteristic (002) peak, located at around a diffraction angle , corresponds to an interlayer spacing of 14.8 Å, indicating a unit-cell dimension with parameter of 30 Å.
Selected area electron diffraction (SAED)
Figure S2 shows electron diffraction in form of a tilting series of . With increasing tilt angle (see the legend to the right), the peak intensity increases. At the same time, the peak intensity decreases.
Switching property
flakes lose their photo-switching property if exposed to a fluence approaching the breakdown. This regime is distinguished by general loss of electron counts in all diffraction rings (Figure S3, red-shaded region) above 1.3 mJ/cm. Figure S3 shows intensity in the diffraction rings and arcs after exposing the samples to increasing laser fluence, in a room-temperature sample (laser off). The threshold character of the arc formation is evident (deep blue line).
The opposing dynamics of and peaks as a reaction to switching the laser on/off is evident from Figure S3. It shows the differential intensity between laser-hot and room-temperature processed . While the arcs disappear in the hot phase (blue color) the diffraction ring gains intensity. The slightly elliptical shape of the rings is due to a higher magnetic lens current used in this data set, leading to a more pronounces astigmatism.
In-situ heating
Thermodynamic heating, performed in situ within the TEM, does not reproduce the nanorippling effect. This observation is additional evidence that the observed MXene rippling requires high-peak-intensity laser irradiation under involvement of non-equilibrium physics.
References
- [1]Anasori, B.; Lukatskaya, M. R.; Gogotsi, Y. 2D Metal Carbides and Nitrides (MXenes) for Energy Storage. Nat. Rev. Mater. 2017, 2 (2), 1–17. https://doi.org/10.1038/natrevmats.2016.98.
- [2]Hantanasirisakul, K.; Gogotsi, Y. Electronic and Optical Properties of 2D Transition Metal Carbides and Nitrides (MXenes). Adv. Mater. 2018, 30 (52). https://doi.org/10.1002/adma.201804779.
- [3]Gogotsi, Y.; Anasori, B. The Rise of MXenes. ACS Nano 2019, 13 (8), 8491–8494. https://doi.org/10.1021/acsnano.9b06394.
- [4]Wang, K.; Zhou, Y.; Xu, W.; Huang, D.; Wang, Z.; Hong, M. Fabrication and Thermal Stability of Two-Dimensional Carbide Ti3C2 Nanosheets. Ceram. Int. 2016, 42 (7), 8419–8424. https://doi.org/10.1016/j.ceramint.2016.02.059.
- [5]Rasool, K.; Helal, M.; Ali, A.; Ren, C. E.; Gogotsi, Y.; Mahmoud, K. A. Antibacterial Activity of Ti3C2Tx MXene. ACS Nano 2016, 10 (3), 3674–3684. https://doi.org/10.1021/acsnano.6b00181.
- [6]Sarycheva, A.; Makaryan, T.; Maleski, K.; Satheeshkumar, E.; Melikyan, A.; Minassian, H.; Yoshimura, M.; Gogotsi, Y. Two-Dimensional Titanium Carbide (MXene) as Surface-Enhanced Raman Scattering Substrate. J. Phys. Chem. C 2017, 121 (36), 19983–19988. https://doi.org/10.1021/acs.jpcc.7b08180.
- [7]Hu, M.; Zhang, H.; Hu, T.; Fan, B.; Wang, X.; Li, Z. Emerging 2D MXenes for Supercapacitors: Status, Challenges and Prospects. Chem. Soc. Rev. 2020, 49 (18), 6666–6693. https://doi.org/10.1039/d0cs00175a.
- [8]Bonse, J.; Krüger, J.; Höhm, S.; Rosenfeld, A. Femtosecond Laser-Induced Periodic Surface Structures. J. Laser Appl. 2012, 24 (4), 042006. https://doi.org/10.2351/1.4712658.
- [9]Florian, C.; Kirner, S. V.; Krüger, J.; Bonse, J. Surface Functionalization by Laser-Induced Periodic Surface Structures. J. Laser Appl. 2020, 32 (2), 022063. https://doi.org/10.2351/7.0000103.
- [10]Satapathy, P.; Pfuch, A.; Grunwald, R.; Das, S. K. Enhancement of Photocatalytic Activity by Femtosecond-Laser Induced Periodic Surface Structures of Si. J. Semicond. 2020, 41 (3). https://doi.org/10.1088/1674-4926/41/3/032303.
- [11]Lange, K.; Schulz-Ruhtenberg, M.; Caro, J. Platinum Electrodes for Oxygen Reduction Catalysis Designed by Ultrashort Pulse Laser Structuring. ChemElectroChem 2017, 4 (3), 570–576. https://doi.org/10.1002/celc.201600630.
- [12]Chang, H. W.; Tsai, Y. C.; Cheng, C. W.; Lin, C. Y.; Lin, Y. W.; Wu, T. M. Nanostructured Ag Surface Fabricated by Femtosecond Laser for Surface-Enhanced Raman Scattering. J. Colloid Interface Sci. 2011, 360 (1), 305–308. https://doi.org/10.1016/j.jcis.2011.04.005.
- [13]Lutey, A. H. A.; Gemini, L.; Romoli, L.; Lazzini, G.; Fuso, F.; Faucon, M.; Kling, R. Towards Laser-Textured Antibacterial Surfaces. Sci. Rep. 2018, 8 (1), 1–10. https://doi.org/10.1038/s41598-018-28454-2.
- [14]Sartori, A. A.; Orlando, S.; Bellucci, A.; Trucchi, D. M.; Abrahami, S.; Boehme, T.; Hantschel, T.; Vandervorst, W.; Buijnsters, J. G. Laser-Induced Periodic Surface Structures (LIPSS) on Heavily Boron-Doped Diamond for Electrode Applications. 2018. https://doi.org/10.1021/acsami.8b15951.
- [15]Naguib, M.; Kurtoglu, M.; Presser, V.; Lu, J.; Niu, J.; Heon, M.; Hultman, L.; Gogotsi, Y.; Barsoum, M. W. Two-Dimensional Nanocrystals Produced by Exfoliation of Ti 3AlC 2. Adv. Mater. 2011, 23 (37), 4248–4253. https://doi.org/10.1002/adma.201102306.
- [16]Shahzad, F.; Alhabeb, M.; Hatter, C. B.; Anasori, B.; Hong, S. M.; Koo, C. M.; Gogotsi, Y. Electromagnetic Interference Shielding with 2D Transition Metal Carbides (MXenes). Science. 2016, 353 (6304), 1137–1140. https://doi.org/10.1126/science.aag2421.
- [17]Li, R.; Zhang, L.; Shi, L.; Wang, P. MXene Ti3C2: An Effective 2D Light-to-Heat Conversion Material. ACS Nano 2017, 11 (4), 3752–3759. https://doi.org/10.1021/acsnano.6b08415.
- [18]Habib, T.; Zhao, X.; Shah, S. A.; Chen, Y.; Sun, W.; An, H.; Lutkenhaus, J. L.; Radovic, M.; Green, M. J. Oxidation Stability of Ti3C2Tx MXene Nanosheets in Solvents and Composite Films. npj 2D Mater. Appl. 2019, 3 (1), 1–6. https://doi.org/10.1038/s41699-019-0089-3.
- [19]Li, J.; Qin, R.; Yan, L.; Chi, Z.; Yu, Z.; Li, N.; Hu, M.; Chen, H.; Shan, G. Plasmonic Light Illumination Creates a Channel to Achieve Fast Degradation of Ti3C2Tx Nanosheets. Inorg. Chem. 2019, 58 (11), 7285–7294. https://doi.org/10.1021/acs.inorgchem.9b00329.
- [20]Li, Q.; Wang, Q.; Li, L.; Yang, L.; Wang, Y.; Wang, X.; Fang, H. T. Femtosecond Laser-Etched MXene Microsupercapacitors with Double-Side Configuration via Arbitrary On- and Through-Substrate Connections. Adv. Energy Mater. 2020, 10 (24), 2000470. https://doi.org/10.1002/aenm.202000470.
- [21]Peng, Y. Y.; Akuzum, B.; Kurra, N.; Zhao, M. Q.; Alhabeb, M.; Anasori, B.; Kumbur, E. C.; Alshareef, H. N.; Ger, M. Der; Gogotsi, Y. All-MXene (2D Titanium Carbide) Solid-State Microsupercapacitors for on-Chip Energy Storage. Energy Environ. Sci. 2016, 9 (9), 2847–2854. https://doi.org/10.1039/c6ee01717g.
- [22]Dong, Y.; Chertopalov, S.; Maleski, K.; Anasori, B.; Hu, L.; Bhattacharya, S.; Rao, A. M.; Gogotsi, Y.; Mochalin, V. N.; Podila, R. Saturable Absorption in 2D Ti3C2 MXene Thin Films for Passive Photonic Diodes. Adv. Mater. 2018, 30 (10). https://doi.org/10.1002/adma.201705714.
- [23]Jiang, X.; Liu, S.; Liang, W.; Luo, S.; He, Z.; Ge, Y.; Wang, H.; Cao, R.; Zhang, F.; Wen, Q.; Li, J.; Bao, Q.; Fan, D.; Zhang, H. Broadband Nonlinear Photonics in Few-Layer MXene Ti3C2Tx (T = F, O, or OH). Laser Photonics Rev. 2018, 12 (2). https://doi.org/10.1002/lpor.201700229.
- [24]Jhon, Y. I.; Koo, J.; Anasori, B.; Seo, M.; Lee, J. H.; Gogotsi, Y.; Jhon, Y. M. Metallic MXene Saturable Absorber for Femtosecond Mode-Locked Lasers. Adv. Mater. 2017, 29 (40). https://doi.org/10.1002/adma.201702496.
- [25]Srinivasan, R.; Lobastov, V. A.; Ruan, C.-Y.; Zewail, A. H. Ultrafast Electron Diffraction (UED). Helv. Chim. Acta 2003, 86 (6), 1761–1799. https://doi.org/10.1002/hlca.200390147.
- [26]Miller, R. J. D. Femtosecond Crystallography with Ultrabright Electrons and X-Rays: Capturing Chemistry in Action. Science. 2014, 343 (6175), 1108–1116. https://doi.org/10.1126/science.1248488.
- [27]Kealhofer, C.; Schneider, W.; Ehlberger, D.; Ryabov, A.; Krausz, F.; Baum, P. All-Optical Control and Metrology of Electron Pulses. Science. 2016, 352 (6284), 429–433. https://doi.org/10.1126/science.aae0003.
- [28]Ehlberger, D.; Mohler, K. J.; Vasileiadis, T.; Ernstorfer, R.; Waldecker, L.; Baum, P. Terahertz Compression of Electron Pulses at a Planar Mirror Membrane. Phys. Rev. Appl. 2019, 11 (2), 24034. https://doi.org/10.1103/PhysRevApplied.11.024034.
- [29]Aidelsburger, M.; Kirchner, F. O.; Krausz, F.; Baum, P. Single-Electron Pulses for Ultrafast Diffraction. Proc. Natl. Acad. Sci. U. S. A. 2010, 107 (46), 19714–19719. https://doi.org/10.1073/pnas.1010165107.
- [30]Kasmi, L.; Kreier, D.; Bradler, M.; Riedle, E.; Baum, P. Femtosecond Single-Electron Pulses Generated by Two-Photon Photoemission Close to the Work Function. New J. Phys. 2015, 17 (3), 33008. https://doi.org/10.1088/1367-2630/17/3/033008.
- [31]Lahme, S.; Kealhofer, C.; Krausz, F.; Baum, P. Femtosecond Single-Electron Diffraction. Struct. Dyn. 2014, 1 (3), 034303. https://doi.org/10.1063/1.4884937.
- [32]Tang, L.; Laughlin, D. E. Electron Diffraction Patterns of Fibrous and Lamellar Textured Polycrystalline Thin Films. I. Theory. J. Appl. Crystallogr. 1996, 29 PART 4, 411–418. https://doi.org/10.1107/S0021889896000404.
- [33]Shi, C.; Beidaghi, M.; Naguib, M.; Mashtalir, O.; Gogotsi, Y.; Billinge, S. J. L. Structure of Nanocrystalline Ti3 C2 MXene Using Atomic Pair Distribution Function. Phys. Rev. Lett. 2013, 112 (12), 125501. https://doi.org/10.1103/PhysRevLett.112.125501.
- [34]Shi, C.; Beidaghi, M.; Naguib, M.; Mashtalir, O.; Gogotsi, Y.; Billinge, S. J. L. Structure of Nanocrystalline Ti3 C2 MXene Using Atomic Pair Distribution Function. Phys. Rev. Lett. 2013, 112 (12), 125501. https://doi.org/10.1103/PhysRevLett.112.125501.
- [35]Alhabeb, M.; Maleski, K.; Anasori, B.; Lelyukh, P.; Clark, L.; Sin, S.; Gogotsi, Y. Guidelines for Synthesis and Processing of Two-Dimensional Titanium Carbide (Ti3C2Tx MXene). Chem. Mater. 2017, 29 (18), 7633–7644. https://doi.org/10.1021/acs.chemmater.7b02847.
- [36]Zhang, Q.; Yan, L.; Yang, M.; Wu, G.; Hu, M.; Li, J.; Yuan, K.; Yang, X. Ultrafast Transient Spectra and Dynamics of MXene (Ti3C2Tx) in Response to Light Excitations of Various Wavelengths. ACS Appl. Mater. Interfaces 2020, 124, 59. https://doi.org/10.1021/acs.jpcc.9b11652.
- [37]Li, J.; Chi, Z.; Qin, R.; Yan, L.; Lin, X.; Hu, M.; Shan, G.; Chen, H.; Weng, Y. X. Hydrogen Bond Interaction Promotes Flash Energy Transport at MXene-Solvent Interface. J. Phys. Chem. C 2020, 124 (19), 10306–10314. https://doi.org/10.1021/acs.jpcc.0c01039.
- [38]Zhang, Q.; Chen, Y.; Zhang, Y.; Sun, J.; Hu, M.; Yan, X.; Yuan, K.; Yang, X.; Li, J. Surface Oxidation Modulates the Interfacial and Lateral Thermal Migration of MXene (Ti3C2Tx) Flakes. J. Phys. Chem. Lett. 2020, 11 (22), 9521–9527. https://doi.org/10.1021/acs.jpclett.0c02886.
- [39]Shao, Y.; Chen, C.; He, Q.; Wu, W.; Li, C.; Gao, Y. Broadband Visible Nonlinear Absorption and Ultrafast Dynamics of the Ti3 C2 Nanosheet. Nanomaterials 2020, 10 (12), 1–11. https://doi.org/10.3390/nano10122544.
- [40]Waldecker, L.; Vasileiadis, T.; Bertoni, R.; Ernstorfer, R.; Zier, T.; Valencia, F. H.; Garcia, M. E.; Zijlstra, E. S. Coherent and Incoherent Structural Dynamics in Laser-Excited Antimony. Phys. Rev. B 2017, 95 (5), 54302. https://doi.org/10.1103/PhysRevB.95.054302.
- [41]Qi, F.; Ma, Z.; Zhao, L.; Cheng, Y.; Jiang, W.; Lu, C.; Jiang, T.; Qian, D.; Wang, Z.; Zhang, W.; Zhu, P.; Zou, X.; Wan, W.; Xiang, D.; Zhang, J. Breaking 50 Femtosecond Resolution Barrier in MeV Ultrafast Electron Diffraction with a Double Bend Achromat Compressor. Phys. Rev. Lett. 2020, 124 (13), 134803. https://doi.org/10.1103/PhysRevLett.124.134803.
- [42]Kampfrath, T.; Perfetti, L.; Schapper, F.; Frischkorn, C.; Wolf, M. Strongly Coupled Optical Phonons in the Ultrafast Dynamics of the Electronic Energy and Current Relaxation in Graphite. Phys. Rev. Lett. 2005, 95 (18), 187403. https://doi.org/10.1103/PhysRevLett.95.187403.
- [43]Carbone, F.; Baum, P.; Rudolf, P.; Zewail, A. H. Structural Preablation Dynamics of Graphite Observed by Ultrafast Electron Crystallography. Phys. Rev. Lett. 2008, 100 (3), 035501. https://doi.org/10.1103/PhysRevLett.100.035501.
- [44]Liu, Y.; Willis, R. F. Plasmon-Phonon Strongly Coupled Mode in Epitaxial Graphene. Phys. Rev. B - Condens. Matter Mater. Phys. 2010, 81 (8), 081406. https://doi.org/10.1103/PhysRevB.81.081406.
- [45]Dar, M. H.; Kuladeep, R.; Saikiran, V.; D., N. R. Femtosecond Laser Nanostructuring of Titanium Metal towards Fabrication of Low-Reflective Surfaces over Broad Wavelength Range. Appl. Surf. Sci. 2016, 371, 479–487. https://doi.org/10.1016/j.apsusc.2016.03.008.
- [46]Kudryashov, S. I.; Nastulyavichus, A. A.; Saraeva, I. N.; Rudenko, A. A.; Zavarny, D. A.; Ionin, A. A. Deeply Sub-Wavelength Laser Nanopatterning of Si Surface in Dielectric Fluids: Manipulation by Surface Plasmon Resonance. Appl. Surf. Sci. 2020, 519, 146204. https://doi.org/10.1016/j.apsusc.2020.146204.
- [47]Mauchamp, V.; Bugnet, M.; Bellido, E. P.; Botton, G. A.; Moreau, P.; Magne, D.; Naguib, M.; Cabioc’h, T.; Barsoum, M. W. Enhanced and Tunable Surface Plasmons in Two-Dimensional Ti3 C2 Stacks: Electronic Structure versus Boundary Effects. Phys. Rev. B - Condens. Matter Mater. Phys. 2014, 89 (23), 235428. https://doi.org/10.1103/PhysRevB.89.235428.
- [48]El-Demellawi, J. K.; Lopatin, S.; Yin, J.; Mohammed, O. F.; Alshareef, H. N. Tunable Multipolar Surface Plasmons in 2D Ti3C2 Tx MXene Flakes. ACS Nano 2018, 12 (8), 8485–8493. https://doi.org/10.1021/acsnano.8b04029.
- [49]Meyer, J. C.; Geim, A. K.; Katsnelson, M. I.; Novoselov, K. S.; Booth, T. J.; Roth, S. The Structure of Suspended Graphene Sheets. Nature 2007, 446 (7131), 60–63. https://doi.org/10.1038/nature05545.
- [50]Gu, T.; Jeong, H.; Yang, K.; Wu, F.; Yao, N.; Priestley, R. D.; White, C. E.; Arnold, C. B. Anisotropic Crystallization in Solution Processed Chalcogenide Thin Film by Linearly Polarized Laser. Appl. Phys. Lett. 2017, 110 (4), 041904. https://doi.org/10.1063/1.4975067.
- [51]Hada, M.; Oba, W.; Kuwahara, M.; Katayama, I.; Saiki, T.; Takeda, J.; Nakamura, K. G. Ultrafast Time-Resolved Electron Diffraction Revealing the Nonthermal Dynamics of near-UV Photoexcitation-Induced Amorphization in Ge2 Sb2 Te 5. Sci. Rep. 2015, 5 (1), 1–10. https://doi.org/10.1038/srep13530.
- [52]Hu, T.; Wang, J.; Zhang, H.; Li, Z.; Hu, M.; Wang, X. Vibrational Properties of Ti3C2 and Ti3C2T2 (T = O, F, OH) Monosheets by First-Principles Calculations: A Comparative Study. Phys. Chem. Chem. Phys. 2015, 17 (15), 9997–10003. https://doi.org/10.1039/c4cp05666c.
- [53]Yorulmaz, U.; Özden, A.; Perkgöz, N. K.; Ay, F.; Sevik, C. Vibrational and Mechanical Properties of Single Layer MXene Structures: A First-Principles Investigation. Nanotechnology 2016, 27 (33). https://doi.org/10.1088/0957-4484/27/33/335702.
- [54]Waldecker, L.; Bertoni, J R; Ernstorfer, R. Compact Femtosecond Electron Diffractometer with 100 KeV Electron Bunches Approaching the Single-Electron Pulse Duration Limit.
- [55]Seidel, M.; Brons, J.; Arisholm, G.; Fritsch, K.; Pervak, V.; Pronin, O. Efficient High-Power Ultrashort Pulse Compression in Self-Defocusing Bulk Media. Sci. Rep. 2017, 7 (1), 1–8. https://doi.org/10.1038/s41598-017-01504-x.
- [56]Liu, X.; Qian, L.; Wise, F. High-Energy Pulse Compression by Use of Negative Phase Shifts Produced by the Cascade χ^(2):χ^(2) Nonlinearity. Opt. Lett. 1999, 24 (23), 1777. https://doi.org/10.1364/ol.24.001777.
- [57]DeSalvo, R.; Vanherzeele, H.; Hagan, D. J.; Sheik-Bahae, M.; Stegeman, G.; Van Stryland, E. W. Self-Focusing and Self-Defocusing by Cascaded Second-Order Effects in KTP. Opt. Lett. 1992, 17 (1), 28. https://doi.org/10.1364/ol.17.000028.
- [58]Shanmugam, J.; Borisenko, K. B.; Chou, Y. J.; Kirkland, A. I. ERDF Analyser: An Interactive GUI for Electron Reduced Density Function Analysis. SoftwareX 2017, 6, 185–192. https://doi.org/10.1016/j.softx.2017.07.001.
- [59]Farrow, C. L.; Juhas, P.; Liu, J. W.; Bryndin, D.; Božin, E. S.; Bloch, J.; Proffen, T.; Billinge, S. J. L. PDFfit2 and PDFgui: Computer Programs for Studying Nanostructure in Crystals. J. Phys. Condens. Matter 2007, 19 (33), 335219. https://doi.org/10.1088/0953-8984/19/33/335219.