In this paper
AbstractIntroductionforeshortening effectOverviewEffect of Sky CurvatureEffect on PUNCH/WFIEffect on Polarimetric AnalysisEffect on Polarization GamutEffect of Optical DistortionSummary and DiscussionReferencesWorksPhysics and Astronomy
Foreshortening of Polarizer Angles in Wide Field Polarizing Imagers
Abstract
The Polarimeter to Unify Corona and Heliosphere (PUNCH) is a very wide field polarizing imager covering a 90 degree diameter region of the sky, stitched together from four individual fields of view (FOVs), three of which are supported by Wide Field Imagers (WFIs) with 40 degree diameter individual FOVs. The science objective requires precise measurement of linear polarization. The WFI FOV is sufficiently wide that polarizer angles are foreshortened by projection effects relative to the line of sight of each pixel in the instrument, deviating from their nominal angular positions of -60, 0, and +60 degree relative to the instrument frame of reference. These angles are foreshortened by the very wide WFI field of view, changing their effective angle across the image plane - an effect that is analogous to similar challenges of polarimetric right/left channel separation in large-format 3D cinema, such as the IMAX format. Using a simple geometrical approach we estimated the perceived polarizer angle in the WFI FOV will vary by +/-2.5 degree for +/-60 degree and +/-3.5 degree for 0 degree polarizer angles. We present the effect of this deviation on the polarized brightness to be recorded by WFI, along with how optical distortion will shift the location of foreshortened angles. We also discuss the implications of this effect on upcoming technologies based on polarimetry across in wide fields.
Introduction
The white-light solar corona consists of a near-constant F-Corona and evolving K-Corona (van de Hulst [39]). The K-corona is predominantly observed through Thomson scattering, resulting in its polarization being oriented at a right angle to the plane formed by the observer, the Sun, and the point of scattering (Billings [5]). The direction of the K-corona’s polarization is therefore aligned to the tangent to the solar limb. Measurement of polarization in the corona and heliosphere has been employed to estimate the coronal electron density (van de Hulst [39]; Saito et al. [36]), for the tomographic reconstruction of 3D electron density in the corona (Davila [8]; Zidowitz [43]; Frazin & Janzen [15]; Kramar et al. [25]; Morgan [31]), to measure 3D characteristics of coronal mass ejections (CMEs; Moran & Davila [30]; Mierla et al. [29]; DeForest et al. [11]; Susino et al. [38]), and to determine the chirality of CMEs (DeForest et al. [10]). Based on an analogy between linear polarization and human color perception (DeForest et al. 2022), Patel et al. (2023) used the 2023 total solar eclipse observations of the middle corona (West et al. [40]) from the Citizen CATE 2024 project (Kovac et al. [24]) to set hue encoding of polarization angle (e.g., Hoeksema et al. [16]) on a rigorous analytical footing.
Coronal polarization has been previously measured by many space-based coronagraphs including Skylab (MacQueen et al. [28]), the Solar and Heliospheric Observatory Large Angle and Spectrometric Coronagraph Experiment (SOHO/LASCO; Brueckner et al. [6]), Sun Earth Connection Coronal and Heliospheric Investigation (SECCHI; Howard et al. [18]) of Solar Terrestrial Relations Observatory and Solar Orbiter Metis (Antonucci et al. [1]). Recently launched missions including Association of Spacecraft for Polarimetric and Imaging Investigation of the Corona of the Sun (ASPI-ICS; Shestov et al. [37]; Zhukov et al. [42]) onboard Project for Onboard Autonomy-3, Coronal Diagnostic Experiment on International Space Station (Cho et al. [7]; Newmark et al. [32]), and Polarimeter to Unify Corona and Heliosphere (PUNCH; DeForest et al. (2022); DeForest et al. [13]) also include white-light imaging polarimeters to probe the corona and heliosphere. The largest field of view (FOV) among the previously flown polarimeters was of LASCO/C3.
The PUNCH Wide Field Imager (WFI; Laurent et al. [27]) has a truncated square field of view (FOV) with a maximum diagonal over . Such a wide FOV introduces new challenges for polarimetry. In particular, objects located at wider incident angles view the instrument polarizer angles foreshortened from their actual angles relative to the instrument boresight, an effect that has been negligible in prior instruments with smaller FOVs.
Previously, the effect of wide viewing angles has been explored for the case of liquid crystal displays (LCDs; Yang & Wu [41]) as LCDs also leverage the phenomenon of polarization. However, Yang & Wu found that even though viewing angles up to could be achieved, they face an issue of light leakage from a weak/spoiled transmission null in the LCD. To overcome such challenges, Ishinabe et al. [23] introduced a new type of wide viewing angle polarizer. Early LCD displays were therefore the subject of much research on the topic of wide-field polarization measurements, with a nice early review by Hong [17]. More recently, photometric and colorimetric properties of polarization were explored by Deun et al. [14] in multi-viewer projector based wide screens. Such systems have been improved over the years with the development of materials optimized for large viewing angles. While LCDs are a different system from polarimetric coronagraphs, there are strong analogies that can be drawn between the two systems’ responses to optical projection of the polarizer angle across a wide FOV.
In this article we describe the effect of large viewing angle with respect to wide field polarizer-based imagers in context of heliospheric imaging, particularly with PUNCH. In Section 2 we introduce the foreshortening effect on polarizer angles due to wide FOV, analyze the effects of projecting curved celestial sphere onto a plane (detector) and discuss its impact for deriving polarized brightness in PUNCH. We finally summarize the work in Section 3.
foreshortening effect
Overview
The projection of a flat optical polarizer into the wide FOV of the WFI instrument is directly analogous to polarization projection effects in the context of 3D cinema viewing, and we therefore explore that system to build intuition and relate the problem to the existing literature in that field. Figure 1a illustrates how a small circle, displayed on a cinema screen, will be projected when viewed at center and at a horizontal angle from the center. In the latter case, the circle with diameter appears as an ellipse with apparent minor axis length , (see Figure 1a), producing a distortion factor (n) given by:
Figure 1. We understand polarizer foreshortening effects in the WFI instrument, by analogy to the terrestrial system of wide-field cinema. (a) Image distortion in a wide-screen cinema flat screen when the viewing angle changes by from the center. (b) Analogy to a cinema screen where two orthogonal lines within the circle at point O with dimension are viewed from point located at longitude and latitude of and respectively and appear as ellipse due to foreshortening. The yellow triangular plane shows the angular separation of point with respect to the reference system in 3D. (c) and (d) represents the distortion of a circle with radius to an ellipse when viewed from a point at distance similar to (b) located at and .
In wide-screen 3D cinema systems, polarizer foreshortening is a concern because polarized glasses are used to separate the right and left visual channels for stereoscopy, using either orthogonal linear polarizing filters or opposed circular filters. In the context of 3D cinema, projection effects in the polarization signal itself induce crosstalk between left- and right-eye channels from the wide field because all spatial dimensions, including those of physical linear polarizers themselves, are subject to the projection/distortion effect described in Equation (1).
A schematic highlighting the geometrical distortion of two foreshortened lines is shown in Figure 1b, where line segments of length located at a source point , and the perceived distances due to the foreshortening observed by an observer positioned at point , a position where a plane-parallel projection1 is assumed. is effectively located at a very large distance ( infinity), and the angular coordinates of the projected lines are at and with respect to the reference position along the azimuthal and elevation direction respectively.
To understand the angular effects on short line segments, such as physical polarizing elements in a linear polarizer, we resolve the foreshortening into vertical and horizontal components. Using Equation (1), the projected lengths of short vertical and horizontal line segments () will be and , respectively. Similarly, a circular geometry, represented in Figure 1c, treated using similar projections, will be distorted to an ellipse, as shown in panel d. Since a short line segment may be considered as a radius of a small circle, characterizing this ellipse is equivalent to characterizing the effect of foreshortening at a single point, on the entire ensemble of possible polarizer orientations at that point. Foreshortening affects the angle subtended by an arc in the circle shown in Figure 1c, measured counterclockwise from the north-south vertical diameter () in the circle. A projected arc with an angle is shown in panel d. If we consider the right-angled triangle with corners , , and , the sides (opposite ) and (adjacent to ) can be represented as sine and cosine components of the hypotenuse, , which is also equal to radius of the circle, . In the foreshortened projection of this circle (Figure 1d), the lengths of the line segments within the circle are modified in a way similar to the vertical and horizontal lines presented in Figure 1b, and as
a result, the sides of the foreshortened triangle can be represented as,
Using the trigonometric relation in the right triangle and solving for the foreshortened angle :
Equation 4 is a simple way to estimate the foreshortened angle if the location of the observation is known with respect to a plane center. In the case of a planar polarizer in front of a wide-field imager such as WFI, the small polarizing elements in the polarizer are projected onto the plane perpendicular to each line of sight and therefore a flat polarizer aligned with the instrument boresight and rotated to angle relative to the instrument acts, for lines of sight different from the boresight itself, as if it were mounted at an angle .
The effect of foreshortening, derived using Equations (2) and (3), on two orthogonal axes when observed by a distant observer is shown in the left panel of Figure 2. The

Figure 2. Plane-parallel projection versus spherical sky geometry. Left to right: apparent lengths along two orthogonal directions and the resulting effective polarizer angles under a plane-parallel projection at the detector plane, illustrating the foreshortening effect for a wide field of view. The background grid shows the curved celestial sphere projected using the azimuthal–equidistant (ARC) projection adopted for PUNCH data products. For clarity, the distortions are exaggerated in both panels. When applied to the vector components of an optical polarizer, this projection-induced distortion leads to systematic, field-dependent rotations of the inferred polarization direction across the wide field of view.
blue vectors illustrate a plane-parallel projection, analogous to a Cartesian grid in which lines of latitude and longitude remain parallel and uniformly spaced, resembling a two-dimensional matrix. The background grid is shown for reference and represents the curved celestial sphere projected using an azimuthal–equidistant (ARC) projection, as adopted in PUNCH data products. This comparison highlights the geometric discrepancy that arises when a locally planar approximation is applied to an intrinsically curved sky. The length of one or both of the axes get shortened with variation in the viewing angle. Along the lines of 0° longitude or latitude the vertical or horizontal axis is shortened, respectively. Whereas, along the diagonal direction the shortening is proportional along both axes, maintaining the aspect ratio, but reducing the overall size of the perceived axes. That portion of the image is compressed along the radial diagonal but not in the perpendicular direction; this additional effect is not shown in this figure. Short vectors that are either radial to the central point, or perpendicular to a radial line (i.e. “tangential”), remain unchanged. Short vectors at oblique angles to the radial are shifted slightly in angle due to the shortening. The right panel of the same figure illustrates the variation in the observed angles derived using Equation (4). The perceived angles are seen to increase along one of the orthogonal axes (in the vertical direction for the presented example) whereas they shrink along the other axes.
Effect of Sky Curvature
When a fixed polarizer orientation in the detector plane is mapped to the celestial sphere through a nonlinear projection (e.g., azimuthal perspective, AZP or equidistant, ARC), the apparent orientation of a given direction is distorted, as illustrated in Figure 3. In the detector-plane, the orientation of the polarizers are depicted with dashed lines. Due to the effect of the image projection, solar north deviates significantly from detector vertical at many locations within the FOV. We compute the resulting deviation between the detector-plane polarizer orientation and the corresponding true-sky orientation.
Figure 3. Figure 3. Effect of sky curvature compared to the detector-plane polarizer orientation. The grid shows the PUNCH FOV in an ARC projection. Left to right: Polarizer orientations in the detector plane are shown as red, green, and blue dashed lines corresponding to polarizer angles of −60°, 0°, and +60° relative to the vertical direction. The corresponding sky-projected orientations exhibit noticeable deviations, illustrating how detector-plane angles distort when mapped onto the curved sky.
For a pixel with helioprojective longitude and latitude (in radians), we compute its angular distance from the reference direction using the haversine formula,
which gives the great-circle separation on a unit sphere. This quantity is required because the mapping between detector-plane angles and spherical angles is nonlinear and depends on the local angular distance from the reference point.
The detector plane radial direction from image center to an arbitrary pixel at coordinates is given by:
which yields an angle measured from detector in counterclockwise direction. The relative angle between the polarizer axis and the local radial direction in the detector plan is therefore
specified within the interval to avoid full redundancies. A line with detector-plane orientation does not retain the same orientation once projected onto the sphere at angular distance . The sky-projected orientation is given by the classical expression for the projection of a local tangent-plane angle onto a spherical surface such as the notional “celestial sphere” at infinite distance:
The deviation between the apparent detector-plane angle and the true-sky orientation is therefore
where
Equation 9 shows that the distortion increases as a function of angular distance from the FOV center and is proportional to —that is, sky orientations become increasingly compressed (relative to planar projections) as grows.
For each pixel we compute
yielding a map of polarization angle deviation (in degrees) across the PUNCH FOV, which is shown in Figure 4. This quantity represents the correction required to convert the measured (detector-plane) polarizer angle to the physically relevant sky orientation at any location in the FOV.

Figure 4. Figure 4. foreshortening effect on the three polarizer angles of WFI observed in the instrument frame. The WFI latitude and longitude correspond to and , described in § 2.1. The panels from left to right correspond to -60°, 0°, and 60° respectively and the colors represent the deviation angle measured at a given location in sky. The non-shaded area in the three panels represent the actual useful WFI FOV.
Effect on PUNCH/WFI
The PUNCH Wide Field Imagers (WFI) and Near Field Imager (NFI) are equipped with polarizers at angles of -60°, 0°, and +60°, a symmetric three-polarizer measurement and representation system (which we refer to as “MZP” for “minus”, “zero” and “plus”, following DeForest et al. 2022). The wide FOV of WFI (up to 50° across) changes the effective angle of each polarizer, depending on location within the FOV. Furthermore, the reference angle used for the MZP system changes with respect to focal plane vertical, across the image plane. The difference in these angles depends on the angles and , the angles measured across the sky from the center of the image, in the horizontal and vertical directions respectively. An overview of this effect is presented in § 2.1.
Figure 4 shows three maps of foreshortened polarizer angles across the PUNCH/WFI FOV for the three polarizer angles, as -60°, 0°, and +60°, respectively. Over the full square FOV, WFI mask corresponding to the real data is overlayed in gray to show the useful FOV. The center of the images corresponds to and , and the whole field is defined with respect to the camera coordinates of longitude and latitude respectively as observed by WFI. The colors in each panel represent the foreshortened angle (IMAX map from Equation 12), which is the difference in perceived angle from the true angle across the FOV. Across the full square field of view, the -60° and +60° polarizers are shifted up to ±2.5° by this effect. For the polarizer the foreshortening is up to ≈3.5°.
Effect on Polarimetric Analysis
We design a simple experiment using an idealized three-polarizer (MZP) system to assess the impact of the foreshortening effect on polarimetric measurements. A linearly polarized input signal with a polarization fraction of 10% is assumed, with the normalization, similar to expected polarization signal levels from heliosphere. Assuming that this polarization is along the vertical direction such that the intensity recorded by the 0° polarizer (Z) is 10%. For an ideal instrument, the intensity
recorded by each polarizer is given by the squared cosine projection of the incident electric field onto the polarizer transmission axis yielding 2.5% polarized signal for M and P polarizers. The three measured intensities, , and , are combined to estimate the total brightness (B), and polarized brightness (pB) and pB’ analogous to Stokes I, Q and U in the solar reference frame using equations 7, 9 and 10 of DeForest et al. (2022).
Using the three maps shown in Figure 4 we generate a cumulative angular perturbation map characterized by adding the three angular deviation maps in quadrature. The resultant map represent the net departure of the perceived polarizer orientations from their ideal configuration. We use the following equations from DeForest et al. (2022) to estimate the fractional errors in B, pB, pB′ due to polarizer misalignment:
where angles are expressed in radians. Figure 5 shows these fractional difference between the expected and measured B, pB and pB′. We find that the foreshortening effect introduces a systematic variation of from the center to the edge of the WFI FOV.

Figure 5. Variation in the polarized brightness in WFI FOV due to foreshortening effect when passed through polarizers at angles and . The colorbar at the top represents the brightness relative to ideal condition. The variation follows the pattern radially outwards as is expected due to curvature in the FOV projection.
Effect on Polarization Gamut
A gamut in colorimetry and color reproduction refers to the range of colors that a device (like a display, printer or camera) can accurately reproduce or measure. It also describe the set of colors within a specific color space, independent of any device. A trichromatic gamut is typically visualized as a triangle in color diagrams, because the “chroma plane” is the plane perpendicular to the R=G=B line in the 3D color space, and a diagonal cut through a cube is a triangle. Consistent with this representation, DeForest et al. (2022) discussed how a triplet (i.e., MZP) measurement of polarization is directly analogous to the red-green-blue (RGB) colorimetry, which Patel et al. [34] demonstrated using real-world polarization observations of the 2023 total solar eclipse. However, it has been established in colorimetry that none of the standard color representation systems fully encompass all the colors visible to the human eye; instead, each system is typically limited to a specific color gamut (e.g., sRGB or Adobe RGB). Since the foreshortening effect alters the perceived polarization states, we encounter deviation from the ideal MZP system, resulting in a measurement that samples only portions of the full polarization gamut.
Following the RGB MZP analogy, Figure 6a depicts an MZP system as a color space. Just as colors in RGB space are formed by linear combinations of base colors, polarization measurements can also be expressed as linear combinations of the MZP bases. The colors in Figure 6a depict the full polarization gamut within the triangle in the diagram. Because the polarizers in the MZP system are not orthogonal to each other, in the solar corona—or in fact in any other MZP measurement—when measuring polarized intensity through a given polarizer angle (e.g., Z), there is always a contribution from the other bases (M and P) as well. Consequently, pure M, Z, or P states are never produced; instead, the measurements form combinations that must fall within the circle inscribed on the full possible gamut (Figure 6b); the circle is a cross-section of the familiar Poincaré sphere, defined by the relation for the familiar Stokes parameters. DeForest et al. (2022) refer to it as the “physical gamut” of MZP measurements.

Figure 6. Effect on the polarization gamut for WFI FOV where MZP states are represented analogously to RGB colors. (a) Reference Cartesian coordinate system for MZP space following Figure 2 of DeForest et al. (2022); the triangular plane shows the ideal polarization gamut with an inscribed circle indicating the reproducible region. (b) Face-on view of the gamut (note the cube orientation), with gray dotted arrows marking about the Z-axis. Blue and magenta dotted lines show extensions to the larger triangle at M, M, P, and P and at Z and Z. Angular deviations are exaggerated here for illustrative purpose. Panels (c)–(e) show gamuts derived from modified MZP combinations, and (f) shows their common overlapping region (see full text of § 2.5 for a complete discussion). Shaded areas outside this region indicate non-reproducible polarization measurements produced by the foreshortening effect.
This same physical gamut is observed when displaying polarized total solar eclipse images, as demonstrated in Patel et al. [34].
When viewed face-on, the measurement gamut appears as an equilateral triangle with vertices M, Z, and P, as shown in Figure 6b. The reference M, Z, P axes have been extended with dashed gray arrows on the opposite side. Angular measurements are taken counterclockwise with respect to the Z axis, following the convention used for position angle measurements from solar north. Due to the foreshortening effect, the effective polarizer angles deviate by approximately and from the nominal and respectively. Consequently, the M and P points shift to M, M, Z, Z, P, and P, respectively; this changes the measurement gamut slightly, limiting the polarization states of light that can be represented by the modified MZP brightnesses, just as modifying the spectrum of primary colors in an RGB system modifies the gamut of colors that can be reproduced by that system.
At the center of the WFI FOV where foreshortening is zero and negligible, polarization gamut within the circular region shown in Figure 6b will be possible. Near the top and bottom regions of the WFI FOV, where the foreshortened angles are approximately , the extent of the measurement gamut becomes limited to the region above the dashed blue line MP. As a result, only polarizations within the region enclosed by the intersection of the circle and the triangle MZP can be measured, as shown by the unshaded region in Figure 6c. Similarly, near the left and right edges of the WFI FOV (Figure 4), where the polarizer angles are reduced to approximately , the gamut is reduced to the intersection of the circle and the triangle MZP, as illustrated in Figure 6d. An alternate possibility with varying MZP points over the gamut is shown in panel (e). The effective intersection based on combinations where the MZP polarizer angles are extremely foreshortened within the WFI FOV is shown as the non-shaded truncated triangular region in panel (f). Note that the truncation of gamut range for the and deviation from the M and P and Z axes respectively shown in Figure 6 is exaggerated to enhance its visibility in the figure. In reality, the modulation is too subtle to produce a noticeable difference in this figure. Thus, the foreshortening of the angles slightly alters the range of polarizations that can be measured or represented using polarizer triplets. The effect is important for measurements of light that is strongly polarized; but it is not significant for WFI in particular, because the overall beam entering the instrument is from a mix of polarized and
unpolarized sources and therefore only weakly polarized overall.
Effect of Optical Distortion
The optical system of telescopes can introduce image distortion, for example, barrel distortion, pincushion distortion, or mustache distortion. This is especially prominent in wide field imagers like PUNCH. This distortion must be accounted in calculations across the wide FOV to determine the offset in the pixels where the light is incident on the detector.
To measure the effects of optical distortion across the WFI FOVs, the PUNCH development team collected 540 images of the night sky at the McDonald Observatory in 2022 June with the WFI engineering model, as described in Hughes et al. [19]. To characterize the optical performance of the WFI instrument, for each image we iteratively alternate between refining the pointing and distortion model.
Using the punchbowl package (Hughes et al. [21]), we measured the image alignment and optical distortion. The code refines image alignment by iteratively correcting distortion. It starts with point spread-function corrected images and identifies stellar centers using Source Extraction and Photometry software (Barbary [3]; Bertin & Arnouts [4]). Using non-linear least squares minimization, it updates the rotation angle and center coordinates, then builds a point-based distortion model. The location of stars in images are determined and compared with the known location of stars from the catalogs to determine the shift in horizontal () and vertical () pixels thus generating a distortion model (Hughes et al. [21]).
The distortion map with shift in and direction is displayed as the magnitude and shown in Figure 7(a). The non-symmetric pattern seen in this panel shows how the incident light is shifted in pixels due to the optical system. This distortion is then folded in with the foreshortening effect to result in a total effect. Panels (b)-(d) of Figure 7 show maps of pixel by pixel difference in M, Z and P polarizer angles shown in Figure 4 and the shifted angles after application of distortion at the same location. The optical distortion shifts the incident light to different pixels and hence it is required to know such small yet important deviations for improved accuracy of polarimetric measurements.
Figure 7. Effect of optical distortion on IMAX maps. (a) The distortion map of magnitude of shift in pixels (). Panels (b)-(d) show the offset in degrees at each pixel for M, Z and P polarizer angles from Figure 4 after an optical distortion has been applied in WFI FOV.
Summary and Discussion
To precisely measure the polarization properties of the solar atmosphere and heliosphere, it is important to identify the geometrical effects present in the remote sensing instrument that measure it. Wide-field imagers such as PUNCH/WFI, equipped with polarizers oriented at , and , are designed to measure the polarimetric properties of the heliosphere with a field of view extending away from the Sun. As the signal at such distances is very faint, it is necessary to understand the effects of wide FOV on the optical system of WFI. We identified the foreshortening of the polarizer angle due to the large FOV of WFI and the geometry of the observation plane with respect to the distant target.
We took inspiration from movie format of IMAX 3D presentations to account for the geometrical effects of a large screen (or FOV) in foreshortening of polarizer angles. Ground-based wide viewing angle optical systems such as wide LCD screen, monitors resolve similar effects in wide viewing angles with the aid of suitable materials along various layers in their screens. However, space-based missions have restrictions from design, space qualification, mass budget and power consumption points of view. Therefore, we aim to correct for the effects introduced in the system by post-processing the data when available on ground.
Using simple geometrical approximations, we investigated how different regions in the WFI FOV will perceive the polarizer angle based on the location of the source in the sky. We found that polarizers at angles of and will have variations of up to and in WFI FOVs. This effect is negligible in field close to the center of observation and increases on moving farther from the center. This geometric deviation is correctable in post processing, using the effective polarizer angle when interpreting the MZP triplet brightness values. If left uncorrected, it would cause small deviations in polarimetric measurements as described by DeForest et al. (2022), potentially affecting line of sight measurements of CME distance and other coronal structures [8, 10].
Given the analogous behavior of the RGB colorspace and MZP polarizer system, an ideal instrument would cover the complete physical gamut within the MZP system, as shown in Figure 6a, Figure 6b. However, due to the impact of the foreshortening effect, the measurable range of polarizations is slightly reduced depending on the location in the sky within the WFI FOV. This is not anticipated to affect the WFI measurements, because the light measured by the instrument is not fully polarized and can be represented within the reduced measurement gamut. Left uncorrected, the variable effective polarizer angles would form a systematic error term in the instrument’s reported values for polarization states in any system, including . However, the effect is correctable mathematically to yield idealized MZP measurements (and corresponding values) at each pixel.
We also analyzed the impact of optical distortion on the foreshortening effect, which is important when obtaining the final image in the WFI cameras. Optical distortion deforms the image by shifting the incident signal by less than 10 pixels, with most of the image experiencing only a few pixels of distortion, while the edges are the most affected. Proper mapping is necessary to accurately record the measurement locations. Additionally, although the deviation of the perceived polarizer angle across the WFI FOV is small, it must be corrected for precise white-light polarimetry of the heliosphere. By using the IMAX formalism described above, combined with an accurate map of the distortion the WFI polarization triplet will be corrected. The corrected images will then be used to accurately derive polarized brightness measurements (See Equation 45 in DeForest et al. 2022). PUNCH-specific corrections are included in the open-source python package, solpolpy [33, 20]. solpolpy is a polarization resolving software suite developed in Python to transform between varying polarization bases that has been developed for the PUNCH data reduction pipeline. The foreshortening effect is corrected while processing the WFI data within solpolpy. The solpolpy package also can convert MZP to other polarization bases, including the widely known Stokes (I, Q, U) parameters.
This analysis is significant for measuring not only polarized signal from the heliosphere, but also to characterize the polarization of the stellar background. WFI data are combined with Narrow Field Imager (NFI) data within the PUNCH data pipeline to create a mosaic image. Given the wide FOV of the WFI instruments, accounting for distortions is crucial, as most overlapping regions are near the edges of the WFI fields of view. These data can only be combined after individual observations have been transformed from camera frames into a common polarization reference frame aligned with solar north and after foreshortening effect corrections, including distortion and coordinate system corrections, have been applied.
PUNCH/WFI is the widest FOV white-light polarimeter flown in space to date. The correction due to foreshortening effect identified for PUNCH/WFI is important and is applicable to similar current and future polarimetric instruments designed to observe such wide FOVs, including terrestrial polarimetric cameras.
This work is funded via the PUNCH project. PUNCH is a NASA Small Explorer mission, funded via NASA Contract No. 80GSFC18C0014. DBS is also supported by NASA Heliophysics US Investigator grant 80NSSC21K1860.
Software: astropy [2, 35], matplotlib [22], astrometry [26], solpolpy [20]
References
- [1]Antonucci, E., Romoli, M., Andretta, V., et al. 2020, A&A, 642, A10, doi: 10.1051/0004-6361/201935338DOI
- [2]Astropy Collaboration, Robitaille, T. P., Tollerud, E. J., et al. 2013, A&A, 558, A33, doi: 10.1051/0004-6361/201322068
- [3]Barbary, K. 2016, Journal of Open Source Software, 1, 58, doi: 10.21105/joss.00058DOI
- [4]Bertin, E., & Arnouts, S. 1996, A&AS, 117, 393, doi: 10.1051/aas:1996164DOI
- [5]Billings, D. E. 1966, A guide to the solar corona
- [6]Brueckner, G. E., Howard, R. A., Koomen, M. J., et al. 1995, SoPh, 162, 357, doi: 10.1007/BF00733434DOI
- [7]Cho, K. S., Bong, S. C., Choi, S., et al. 2017, Journal of Korean Astronomical Society, 50, 139, doi: 10.5303/JKAS.2017.50.5.139DOI
- [8]Davila, J. M. 1994, ApJ, 423, 871, doi: 10.1086/173864DOI
- [10]DeForest, C. E., de Koning, C. A., & Elliott, H. A. 2017, ApJ, 850, 130, doi: 10.3847/1538-4357/aa94caDOI
- [11]DeForest, C. E., Howard, T. A., & Tappin, S. J. 2013, ApJ, 765, 44, doi: 10.1088/0004-637X/765/1/44DOI
- [13]DeForest, C. E., Gibson, S. E., Killough, R., et al. 2026, SoPh, 301, 16, doi: 10.1007/s11207-026-02608-2DOI
- [14]Deun, T. L., Stoenescu, D., & de Bourgnet de la Tocnaye, J.-L. 2019, Optical Engineering, 58, 103108. https://api.semanticscholar.org/CorpusID:208014373
- [15]Frazin, R. A., & Janzen, P. 2002, ApJ, 570, 408, doi: 10.1086/339572DOI
- [16]Hoeksema, J. T., Liu, Y., Hayashi, K., et al. 2014, Solar Physics, 289, 3483
- [17]Hong, Q. 2006, PhD thesis, University of Central Florida, USA. https://palmm.isle.uflvc.org/islandora/wide-viewing-angle-liquid-crystal-displays
- [18]Howard, R. A., Moses, J. D., Vourlidas, A., et al. 2008, SSRv, 136, 67, doi: 10.1007/s11214-008-9341-4DOI
- [19]Hughes, J. M., DeForest, C. E., & Seaton, D. B. 2023, AJ, 165, 204, doi: 10.3847/1538-3881/acc578DOI
- [20]Hughes, J. M., Patel, R., West, M., et al. 2024, solpolpy, 0.4.0, Zenodo, doi: 10.5281/zenodo.14207554
- [21]Hughes, J. M., Lowder, C., Van Kooten, S., et al. 2025, punchbowl, 0.0.20, doi: 10.5281/zenodo.14209123
- [22]Hunter, J. D. 2007, Computing in Science & Engineering, 9, 90, doi: 10.1109/MCSE.2007.55
- [23]Ishinabe, T., Miyashita, T., & Uchida, T. 2002, Japanese Journal of Applied Physics, 41, 4553, doi: 10.1143/JJAP.41.4553DOI
- [24]Kovac, S. A., Caspi, A., Seaton, D. B., et al. 2026, SoPh, 301, 12, doi: 10.1007/s11207-025-02588-9DOI
- [25]Kramar, M., Jones, S., Davila, J., Inhester, B., & Mierla, M. 2009, SoPh, 259, 109, doi: 10.1007/s11207-009-9401-2DOI
- [26]Lang, D., Hogg, D. W., Mierle, K., Blanton, M., & Roweis, S. 2010, The Astronomical Journal, 137, 1782
- [27]Laurent, G. T., DeForest, C. E., Beasley, M. N., et al. 2026, SoPh, 301, 112, doi: 10.1007/s11207-026-02706-1DOI
- [28]MacQueen, R. M., Eddy, J. A., Gosling, J. T., et al. 1974, ApJL, 187, L85, doi: 10.1086/181402DOI
- [29]Mierla, M., Inhester, B., Marqué, C., et al. 2009, SoPh, 259, 123, doi: 10.1007/s11207-009-9416-8DOI
- [30]Moran, T. G., & Davila, J. M. 2004, Science, 305, 66, doi: 10.1126/science.1098937DOI
- [31]Morgan, H. 2015, ApJS, 219, 23, doi: 10.1088/0067-0049/219/2/23DOI
- [32]Newmark, J. S., Gopalswamy, N., Kim, Y. H., et al. 2020, in AGU Fall Meeting Abstracts, Vol. 2020, SH028–0011
- [33]Patel, R., Hughes, J. M., West, M. J., et al. 2024, in 2024 IEEE Southwest Symposium on Image Analysis and Interpretation (SSIAI), 57–60, doi: 10.1109/SSIAI59505.2024.10508701DOI
- [34]Patel, R., Seaton, D. B., Caspi, A., et al. 2023, Research Notes of the American Astronomical Society, 7, 241, doi: 10.3847/2515-5172/ad0b0dDOI
- [35]Price-Whelan, A. M., Sipőcz, B. M., Günther, H. M., et al. 2018, AJ, 156, 123, doi: 10.3847/1538-3881/aabc4f
- [36]Saito, K., Poland, A. I., & Munro, R. H. 1977, SoPh, 55, 121, doi: 10.1007/BF00150879DOI
- [37]Shestov, S. V., Zhukov, A. N., Inhester, B., Dolla, L., & Mierla, M. 2021, A&A, 652, A4, doi: 10.1051/0004-6361/202140467DOI
- [38]Susino, R., Bemporad, A., & Dolei, S. 2014, ApJ, 790, 25, doi: 10.1088/0004-637X/790/1/25DOI
- [39]van de Hulst, H. C. 1950, BAN, 11, 135
- [40]West, M. J., Seaton, D. B., Wexler, D. B., et al. 2023, SoPh, 298, 78, doi: 10.1007/s11207-023-02170-1DOI
- [41]Yang, D. K., & Wu, S. T. 2014, Reflective and Transflective Liquid Crystal Displays (John Wiley & Sons, Ltd), 285–319, doi: https://doi.org/10.1002/9781118751992
- [42]Zhukov, A. N., Thizy, C., Galano, D., et al. 2025, arXiv e-prints, arXiv:2509.00253, doi: 10.48550/arXiv.2509.00253DOI
- [43]Zidowitz, S. 1999, J. Geophys. Res., 104, 9727, doi: 10.1029/1998JA900099DOI


