WorksPhysics and Astronomy
Effects of W alloying on the electronic structure, phase stability and thermoelectric power factor in epitaxial CrN thin films
Abstract
CrN-based alloy thin films are of interest as thermoelectric materials for energy harvesting. Ab initio calculations show that dilute alloying of CrN with 3 at.% W substituting Cr, induce flat electronic bands and push the Fermi level EF into the conduction band, while retaining dispersive Cr 3d bands. These features are conducive for both high electrical conductivity σand high Seebeck coefficient α, and hence the thermoelectric power factor α^2σ. To investigate this possibility, epitaxial CrWxNz films were grown on c-plane sapphire by dc-magnetron sputtering. However, even films with the lowest W concentration (x = 0.03) in our study contained metallic h-Cr2N, which is not conducive for a high α. Nevertheless, the films exhibit a sizeable power factor of α^2σ~ 4.7 x 10-4 Wm-1K-2 due to high σ~ 700 Scm-1, and a moderate α~ -25 ~{^^^^00b5}V/K. Increasing h-Cr2N fractions in the 0.03 < x \le 0.19 range monotonically increases σ, but severely diminishes αleading to two orders of magnitude decrease in α^2σ. This trend continues with x > 0.19 due to W precipitation. These findings indicate that dilute W additions below its solubility limit in CrN is important for realizing high thermoelectric power factor in CrWxNz alloy films.
below its solubility limit in CrN is important for realizing high thermoelectric power factor in alloy films.
Introduction
Transition metal nitrides (TMNs) constitute an important class of materials that exhibit a combination of high hardness, mechanical strength, thermal stability and corrosion resistance [1]. TMNs such as TiN, HfN and ZrN have been used as protective and decorative coatings, and nanolayers of metallic TMNs are used as diffusion barriers in nanodevice wiring architectures in integrated circuits [2, 3, 4, 5]. Narrow-bandgap thin films of TMNs, such as, CrN- and ScN-based alloys, have been considered for thermoelectric and piezoelectric energy conversion [6, 7, 8, 9]. ScAlN films exhibit large piezoelectric responses at 500 °C making them suitable for high-temperature device applications [10, 11, 12].
Thermoelectric conversion efficiency is related to a dimensionless figure of merit , where is the absolute temperature, is the Seebeck coefficient, the electrical conductivity, the thermal conductivity [13, 14] and is the thermoelectric power factor.
Realizing high is a fundamental challenge that requires the circumvention of unfavorable couplings between , and . enhancement strategies include doping (less than a few at.%) [15] and/or alloying (several at.% or more) [16] to increase by manipulating the electronic structure, and decreasing by impurity- and nanostructuring-induced phonon scattering [17, 18].
CrN-based alloys have inherently high thermoelectric power factors [19, 20, 21] due to the narrow bandgap of CrN () which simultaneously induces high and high underpinned by high charge carrier entropy near the Fermi level . These attributes, together with an intrinsically low when compared to other TMNs [22], due to low phonon lifetimes arising from spin-lattice coupling [23, 24], make CrN an attractive candidate for enhancing through doping and alloying. Substituting Cr () with W () in CrN offers the possibility to not only manipulate and , but also decrease due to the atomic mass contrast between W and Cr. Indeed, adding W or V to CrN increase , but increases only for W additions which decrease , [25] unlike V additions which increase [26]. Understanding the effects of W alloying on the electronic structure, phase stability and film morphology are crucial for understanding and tuning the thermoelectric properties to realize high in CrN-based films.
Here, we show from ab initio calculations that dilute substitutions of Cr with W in CrN result in flat electronic bands near the Fermi level , which is pushed into the conduction band. These features are conducive for high as well as high , and hence, a high power-factor .
To examine this experimentally, we attempted to grow epitaxial films, and measured and as a function of W content . We find that W additions monotonically increase , but severely diminish due to increasing fractions of metallic - and W precipitation. These findings indicate that restricting W content to below its solubility limit in CrN is crucial for realizing high in alloys.
Methods
Computational details
The electronic structures of cubic with and in double layer antiferromagnetic (AFM ) configuration were computed by density functional theory calculations (DFT) using projector-augmented-wave (PAW) potentials as implemented in the Vienna ab initio simulation package (VASP) code [27, 28]. The exchange-correlation energy was treated within the LDA + U scheme with eV [29] to consider Coulombic interactions in the narrow Cr bands, and counteract bandgap underestimation or absence by local approaches. The cutoff energy of plane waves for the expansion of wavefunctions was set to 520 eV. Brillouin zone sampling was carried out on a Monkhorst-Pack mesh, and the electronic optimization criterion was set to eV. A supercell of 64 atoms was used to analyze the equation of state (EOS) to estimate the equilibrium lattice constant . The crystal structure was visualized using Vesta [30] and the electronic structures were plotted using Sumo package [31].
Experimental details
thin films with were grown in an ultra-high vacuum chamber with a base pressure of Pa [29] by DC magnetron sputtering onto 10 x 10 mm -plane sapphire substrates (Alineason Materials Technologies). Prior to film growth, the substrates were ultrasonicated successively in acetone and ethanol for 10 minutes each, followed by blow drying with a gas jet. The films were sputter-deposited from 50-mm-diameter disc-shaped targets of Cr and W (both 99.95% purity) using a 0.33 Pa ( mTorr) plasma struck with a 40/60 Ar/ mixture. The W level was varied by fixing the Cr target power constant and varying the W target power in the range. During film deposition, the substrates were at 600 °C and rotated at 15 rpm.
Phase purity and crystal structure were characterized by X-ray diffractometry (XRD) using a PANanalytical X’Pert Pro instrument with a Cu-K radiation source operated at 45 kV and 40 mA. Pole figure measurements were carried out by scanning along in-plane rotation and out-of-plane tilt angles at 2.5° steps per second using cross-slit primary optics and parallel plate collimator secondary optics. Film thickness, roughness, and density were estimated by analyses of X-ray reflectivity (XRR) data acquired using a hybrid-mirror module with a 0.5° incidence slit and a 0.125° post-diffraction slit. Film morphology was examined by scanning electron microscopy (SEM) in a Sigma 300 Zeiss instrument operated at 3 kV using Inlens detector. Measurement of composition of the films was carried out by combination of Rutherford backscattering spectrometry (RBS) and time-of-flight elastic recoil detection analysis (ToF-ERDA). Experiments were performed using 5 MV 15-SDH2 Pelletron accelerator at Tandem Laboratory, Uppsala University [32]. 2 MeV primary ion beam was incident at to the sample normal and the backscattered particles were detected at an angle of . The acquired spectra was processed and analysed using the SIMNRA [33] software, version 7.03. For ToF-ERDA measurements, 44 MeV iodine () beam was incident at an angle of with the sample surface normal. The incident ions created recoils which passed through the time-of-flight detector and gas ionization chamber, placed at an angle of relative to the incident beam. The elemental depth profile was extracted from the time and energy coincidence spectra using Potku 2.0 code [34].
Room-temperature electrical conductivity was measured by using a Jandel Model RM3000 four-point-probe station. Seebeck coefficient, was measured using a home-made setup equipped with Peltier devices that maintain desired temperature gradient across the sample. In this setup, temperatures are measured with K-type thermocouples, and the Seebeck voltage is measured with a Keithley 2001 multimeter as described elsewhere [35]. Charge carrier density and mobility were measured by room-temperature Hall measurements in a home-made setup with a 0.485 T permanent magnet. The Hall voltage was measured in the van der Pauw configuration with a Keithley 2100 multimeter, with a 40-mA current supplied by a Keithley 2400 source.
Results and discussion
Ab-initio calculations
CrN undergoes a magnetostructural transition at the Néel temperature K, wherein the antiferromagnetic low-temperature orthorhombic phase is converted to the hightemperature paramagnetic rocksalt phase [36]. However, cubic CrN is known to energetically favor the antiferromagnetic spin configuration with alternating double layers of identical spin perpendicular to the crystallographic [110] direction (AFM-110) as shown in Figure 1a [33]. The equilibrium lattice parameter of cubic CrN was estimated by fitting energy (E) vs volume (V) to obtain Å for CrN (Figure 1b), which agrees well with prior theoretical and experimental reports [38, 39]. For CrWN with , we obtain Å for W occupancy of either or sites, suggesting no observable site-occupancy effect. Thus, we calculated the electronic properties only for W substitution at sites.

Figure 1. (a) A sketch of the cubic CrN crystal structure showing (red) and (green) sites, with W substitution at the sites. (b) Murnaghan fits for CrN and CrWN. Density of states plots for (c) CrN and (d) CrWN.
For pristine defect-free CrN, the calculated bandgap eV agrees with prior work [37], and the Cr 3d states are the primary contributors to the states near (see Figure 1c).
For , the is inside the conduction band (Figure 1d) and is associated with a significantly higher density of states near than in CrN. This W-induced shift into the conduction band is likely to produce metal-like electrical transport, commonly observed in degenerate semiconductors.
Electronic structure calculations for CrN along the high symmetry X--K-W-X path reveal dispersive Cr bands with conduction band minima at , and a bandgap of eV (Figure 2a). Substituting Cr with 3 at.% W, i.e., , largely preserves the CrN band structure, but results in additional flat bands with a strong W- character near . The simultaneous presence of dispersive and flat bands, and high density of states near are conducive for high in with . Dispersive bands favor high carrier mobility , and hence, high . Flat narrow bands favor high due to the high effective mass as seen from , where is the charge carrier density [13]. Thus, higher tends to decrease leading to the inverse coupling between and . Thus, the presence of both narrow as well as highly dispersive bands are necessary for realizing high [36].

Figure 2. Electronic band structures computed by ab initio calculations along X--K-W-X for (a) CrN and (b) .
Epitaxial growth and structural analysis
To experimentally investigate our theoretical predictions, we attempted to grow epitaxial films. We chose a growth temperature of 600 °C because epitaxial rocksalt CrN is favored in the 550 °C 700 °C range [41], and metallic -CrN formation at higher temperatures is not conducive for high . Cr target power is also a crucial parameter that influences CrN and -CrN phase selection and fractions, and Cr vacancy concentration that can impact [42]. Results of our studies of CrN films grown with 42 W 50 W showed that the highest was obtained for (see supplementary information Figure S1). Accordingly, films were deposited for different at a fixed W.

Figure S1. (a) X-ray diffractograms, and (b) thermoelectric power factor, of CrN films as a function of Cr target power .
RBS and ERDA analyses showed that all the films were nitrogen-deficient (see Table I). Increasing in the range increased the W content from to 0.25, decreased the nitrogen content from to 0.21, and increased oxygen contamination from 1.7 at. % to 5.5 at.%. The large decreases in nitrogen content correlating with increasing W content suggests the formation of a Cr-rich CrN, corroborated by XRD analyses described below.
| Cr | W | N | O | |
| 51.6 | - | 46.9 | 1.7 | 0.91 |
| 50.5 | 3.4 | 43.4 | 2.8 | 0.80 |
| 58.4 | 6.8 | 30.6 | 4.2 | 0.47 |
| 55.8 | 18.9 | 21.0 | 4.3 | 0.28 |
| 53.0 | 25.1 | 16.4 | 5.5 | 0.21 |
Table I. Elemental compositions of CrWN films determined by RBS and ToF-ERDA.

Figure 3. X-ray diffractograms from (a) films with . Here, * represents the substrate 006 peak at (b) Lattice parameters of CrN and - for films with .
X-ray diffractograms show that W additions shift the 111 and 222 CrN Bragg peaks to higher angles, i.e., lower d-spacings, indicative of W-induced unit cell compression. Even for , the lowest W content explored in this study, we observe the - (0002) reflection at . The results indicate that the solubility limit of W in CrN is less than even under the far-from equilibrium conditions involved during sputter deposition. Our attempts to obtain CrN films with lower W contents were unsuccessful due to the instability of the plasma at low . Thus, alternative approaches need to be implemented for achieving desired dilute W concentrations in CrN films.
At , the CrN peaks continue to shift further but considerably decrease in intensity, while the - 0002 peak intensity increases and the - 0004 peak appears at .
No rocksalt CrN peaks were detectable in diffractograms from films with , whereas the -CrN peaks were stronger. Films with exhibit 110 and 220 Bragg peaks at and from metallic W, showing the coexistence of metallic -CrN and W.
X-ray pole figures of the 111 and 002 reflections from the CrN and CrWN films, respectively, show distinct spot patterns at specific angles (Figure 4) confirming the epitaxial growth of CrWN films. Scans of the poles with Bragg angle show a central peak and 6 peaks at (Figure 4a). Here, the presence of 6 peaks rather than 3 expected is indicative of twin domains seen in epitaxial films of rocksalt structure materials grown on -plane sapphire. Pole figure performed at on the CrWN film reveals the presence of 6 poles at with a symmetry of 3 (Figure 4(b)). These poles correspond to the reflection from -CrN and demonstrating its epitaxial character.

Figure 4. Pole figure scans from CrN and CrWN film grown on -plane sapphire for (a) reflections at and (b) reflections at , respectively.
Analyses of XRR data (See supplementary, Figure S1) show that all the CrWN films were nm thick with a roughness of nm, irrespective of the W content. The film density increased from to as the W content was increased from to .
The baseline density for CrN films was which is of the theoretical density of CrN.
Morphological studies
W alloying had a significant effect on the CrWN film morphology. Pristine CrN film surface exhibit large triangular grains (Fig. 5(a)) indicative of 111-oriented rocksalt films [43].
In contrast, films with show highly elongated grains with an average width of nm, however, the average lengths of these grains are difficult to calculate due to continuous and curved domains (Fig. 5(b)). Films with higher W contents show a different morphology indicative of fine -CrN grains. However, for , we observe a dense morphology (Fig. 5(c)). Films with and (Fig. 5(d-e)) both exhibit similar features having average grain size nm, but with the presence of voids. Increasing the W content leads to grain refinement, -CrN formation and W precipitation. The grain size distribution for the corresponding films is plotted in Fig 5(f-h). Figure S3 show elemental mapping of films with , showing that the W precipitates are homogeneously distributed throughout the film.

Figure S3. (a-c) Elemental EDX maps of Cr and W from CrWN films.

Figure 5.
Figure 5 (PDF p. 12). (a-e) SEM micrographs from CrWN films with , and (f–h) corresponding grain size distribution plot with Gaussian fit.
Thermoelectric transport properties
The room-temperature values of and measured from the films are plotted in Figure 6 as a function W alloying content. Pristine CrN shows Scm which agrees with prior reports for CrN films deposited under similar conditions [5]. Adding W increases to Scm for , which is in accordance with the W-induced changes in the electronic band structure and increase in the density of states at the Fermi level indicated by our ab initio calculations.

Figure 6. (a) Seebeck coefficient, electrical conductivity, and corresponding power factor, and (b) carrier density and mobility extracted from Hall measurements in CrWN films.
For , however, our theoretical calculations do not directly apply because of -CrN phase formation that was not considered in our computations. Films with higher W contents in the range exhibit no considerable changes in suggesting that the increase in expected from increased metallic -CrN fraction is countered by the decreased rocksalt CrN fraction. At , increases to Scm due to W precipitation [44].
The thermoelectric properties and the Hall measurement analyses are shown in Fig. 5. All the films show negative , indicating n-type behavior, i.e., electrons are the majority charge carriers. Pristine CrN shows high V/K which reduces greatly to V/K for . Experimental observation of lower for as contrary to the theoretical calculations infers one needs to explore much lower W content CrN films to avoid formation of secondary phases. With even higher W content (), reduces further and saturates around V/K due to the increased metallic -CrN phase.
The room-temperature power factor WmK for CrN is in close agreement as reported by Kerdsongpanya et al., ( WmK) [21], but lower than those of Gharavi et al., (-11 WmK) [45]. However, due to the reduced , all the films with W shows lowered values.
Analyses of Hall measurements of the CrWN films (Fig. 5 (b)) indicate W additions result in a up to four-orders-of-magnitude increase in charge carrier density , accompanied by a two-orders of magnitude decrease in carrier mobility . The large increase in carrier density are due to metallic -CrN [46] and W precipitation. The measured cm for CrN agrees well with prior reports [21]. The low is typical of metals and is attributable to grain-boundary and W impurity scattering mechanisms. Since and are strongly and adversely coupled through , the monotonic rise in increases but decreases , leading to a net decrease in .
Thus, it is crucial to restrict W additions to below its solubility limit in CrN to preclude the formation of -CrN and W precipitation to realize high .
Conclusions
Ab initio calculations indicate that dilute W additions to CrN are attractive to increase the thermoelectric power factor due to the emergence of flat bands near the Fermi level pushed into the conduction band. Epitaxial growth of dc-magnetron sputtered W alloyed CrN films showed metallic -CrN formation even for the smallest W contents explored in this study. Despite this, the power factor is considerable at due to high S cm and sizeable $\alpha = -25 . Increasing W content severely diminishes despite the monotonic increase in due to increasing -CrN fraction and W precipitation. These findings indicate that limiting W alloying to below its solubility limit in CrN is crucial for realizing a high power factor.
Conflict of interest
The authors declare no conflict of interest.
Data availability
Data is available from the corresponding author on reasonable request.
Acknowledgements
The authors acknowledge funding from the Swedish Government Strategic Research Area in Materials Science on Functional Materials at Linköping University (Faculty Grant SFO-Mat-LiU No. 2009 00971), the Knut and Alice Wallenberg foundation through the Wallenberg Academy Fellows program (KAW-2020.0196), the Swedish Research Council (VR) under Project No. 2021-03826, and the Swedish Energy Agency under project number 52740-1. NKS and PE acknowledge support from the Foundation Olle Engkvist Byggmästare, grant no. 218-0076. NKS acknowledges Dr Rui Shu for his help during the initial experimental phase. GR gratefully acknowledges funding from the US National Science Foundation grant CMMI 2135725 through the BRITE program. DG acknowledges support from the Swedish Research Council (VR) International Postdoc Grant 2023-00208. BA acknowledges financial support from the Swedish Research Council (VR) through Grant No. 2019-05403 and 2023-05194. The computations were enabled by resources provided by the National Academic Infrastructure for Supercomputing in Sweden (NAISS), at the National Supercomputer Center (NSC), partially funded by the Swedish Research Council through grant agreements no. 2022-06725.
Prior to depositing films with different W contents, CrN films were deposited at different Cr target power to preclude the formation of formation and Cr-deficient films. X-ray diffractograms from films deposited with 42 W 46 W (Figure S1) show 111 and 222 Bragg peaks from rocksalt CrN indicating a lattice parameter of 4.17 Å [9]. The 0006 peak is from the sapphire substrate. At W, we observe large 0002 peaks from - corresponding to 4.48 Å, and a weak CrN 111 peak. Among these, CrN film grown at 44 W showed the highest thermoelectric power factor, (Figure S1).
The XRR data was fitted to extract the film thickness, roughness and density (see Figure S2).

Figure S2. (a) Measured XRR data and fits for CrWN () films and (b) the extracted values of film thickness and density.
CrWN films with the highest W content of showed homogenous contrast from elemental W indicating homogeneous distribution of W and Cr (Figure S3).
References
- [1]R. S. Ningthoujam and N. S. Gajbhiye, Synthesis, Electron Transport Properties of Transition Metal Nitrides and Applications, Prog. Mater. Sci. 70, 50 (2015).DOI
- [2]D. D. Kumar, N. Kumar, S. Kalaiselvam, S. Dash, and R. Jayavel, Wear Resistant Super-Hard Multilayer Transition Metal-Nitride Coatings, Surfaces and Interfaces 7, 74 (2017).DOI
- [3]F. Lévy, P. Hones, P. E. Schmid, R. Sanjinés, M. Diserens, and C. Wiemer, Electronic States and Mechanical Properties in Transition Metal Nitrides, Surf. Coatings Technol. 120–121, 284 (1999).DOI
- [4]M. A. Vaslyyev, B. N. Mordyuk, S. I. Sidorenko, S. M. Voloshko, A. P. Burmak, I. O. Krulhov, and V. I. Zakiev, Characterization of ZrN Coating Low-Temperature Deposited on the Preliminary Ar + Ions Treated 2024 Al-Alloy, Surf. Coatings Technol. 361, 413 (2019).
- [5]G. Wang, Y. Si, M. Wen, J. Qiu, S. Zhang, Q. Song, W. Wang, X. Yang, and P. Ren, Microstructure, Mechanical and Tribological Behaviors of Hard-yet-Tough Hf-Ag-N Coating, J. Mater. Res. Technol. 22, 2030 (2023).DOI
- [6]S. Kerdsongpanya, N. Van Nong, N. Pryds, A. Žukauskaitė, J. Jensen, J. Birch, J. Lu, L. Hultman, G. Wingqvist, and P. Eklund, Anomalously High Thermoelectric Power Factor in Epitaxial ScN Thin Films, Appl. Phys. Lett. 99, (2011).DOI
- [7]P. V. Burmistrova, J. Maassen, T. Favaloro, B. Saha, S. Salamat, Y. Rui Koh, M. S. Lundstrom, A. Shakouri, and T. D. Sands, Thermoelectric Properties of Epitaxial ScN Films Deposited by Reactive Magnetron Sputtering onto MgO(001) Substrates, J. Appl. Phys. 113, (2013).DOI
- [8]C. X. Quintela, B. Rodríguez-González, and F. Rivadulla, Thermoelectric Properties of Heavy-Element Doped CrN, Appl. Phys. Lett. 104, 1 (2014).DOI
- [9]C. X. Quintela et al., Epitaxial CrN Thin Films with High Thermoelectric Figure of Merit, Adv. Mater. 27, 3032 (2015).DOI
- [10]M. Akiyama, T. Kamohara, K. Kano, A. Teshigahara, Y. Takeuchi, and N. Kawahara, Enhancement of Piezoelectric Response in Scandium Aluminum Nitride Alloy Thin Films Prepared by Dual Reactive Cosputtering, Adv. Mater. 21, 593 (2009).DOI
- [11]F. Tasnádi, B. Alling, C. Höglund, G. Wingqvist, J. Birch, L. Hultman, and I. A. Abrikosov, Origin of the Anomalous Piezoelectric Response in Wurtzite ScAl1-XN Alloys, Phys. Rev. Lett. 104, 1 (2010).
- [12]A. Zukauskaite, G. Wingqvist, J. Palisaitis, J. Jensen, P. O. A. Persson, R. Matloub, P. Muralt, Y. Kim, J. Birch, and L. Hultman, Microstructure and Dielectric Properties of Piezoelectric Magnetron Sputtered W-Sc XAl 1-XN Thin Films, J. Appl. Phys. 111, 1 (2012).
- [13]G. J. Snyder and E. S. Toberer, Complex TE Materials, Nat. Mater. 7, 105 (2008).
- [14]S. Bathula, M. Jayasimhadri, B. Gahtori, N. K. Singh, K. Tyagi, A. K. Srivastava, and A. Dhar, The Role of Nanoscale Defect Features in Enhancing the Thermoelectric Performance of P-Type Nanostructured SiGe Alloys, Nanoscale 7, 12474 (2015).DOI
- [15]R. J. Mehta, Y. Zhang, C. Karthik, B. Singh, R. W. Siegel, T. Borca-Tasciuc, and G. Ramanath, A New Class of Doped Nanobulk High-Figure-of-Merit Thermoelectrics by Scalable Bottom-up Assembly, Nat. Mater. 11, 233 (2012).DOI
- [16]D. Wines, F. Ersan, and C. Ataca, Engineering the Electronic, Thermoelectric, and Excitonic Properties of Two-Dimensional Group-III Nitrides through Alloying for Optoelectronic Devices (B1-XAlXN, Al1-XGaXN, and Ga1-XInXN), ACS Appl. Mater. Interfaces 12, 46416 (2020).DOI
- [17]J. R. Sootsman, D. Y. Chung, and M. G. Kanatzidis, New and Old Concepts in Thermoelectric Materials, Angew. Chemie - Int. Ed. 48, 8616 (2009).DOI
- [18]C. J. Vineis, A. Shakouri, A. Majumdar, and M. G. Kanatzidis, Nanostructured Thermoelectrics: Big Efficiency Gains from Small Features, Adv. Mater. 22, 3970 (2010).DOI
- [19]P. Eklund, S. Kerdsongpanya, and B. Alling, Transition-Metal-Nitride-Based Thin Films as Novel Energy Harvesting Materials, J. Mater. Chem. C 4, 3905 (2016).pubmed.ncbi.nlm.nih.gov/27358737
- [20]S. Kerdsongpanya, B. Alling, and P. Eklund, Effect of Point Defects on the Electronic Density of States of ScN Studied by First-Principles Calculations and Implications for Thermoelectric Properties, Phys. Rev. B - Condens. Matter Mater. Phys. 86, 1 (2012).DOI
- [21]S. Kerdsongpanya, B. Sun, F. Eriksson, J. Jensen, J. Lu, Y. K. Koh, N. Van Nong, B. Balke, B. Alling, and P. Eklund, Experimental and Theoretical Investigation of Cr1-XScX/N Solid Solutions for Thermoelectrics, J. Appl. Phys. 120, (2016).
- [22]W. Lengauer, Nitrides: Transition Metal Solid-State Chemistry, in Encyclopedia of Inorganic and Bioinorganic Chemistry (John Wiley & Sons, Ltd, 2015), pp. 1–24.DOI
- [23]I. Stockem, A. Bergman, A. Glensk, T. Hickel, F. Körmann, B. Grabowski, J. Neugebauer, and B. Alling, Anomalous Phonon Lifetime Shortening in Paramagnetic CrN Caused by Spin-Lattice Coupling: A Combined Spin and Ab Initio Molecular Dynamics Study, Phys. Rev. Lett. 121, 125902 (2018).
- [24]O. Jankovský, D. Sedmidubský, Š. Huber, P. Šimek, and Z. Sofer, Synthesis, Magnetic and Transport Properties of Oxygen-Free CrN Ceramics, J. Eur. Ceram. Soc. 34, 4131 (2014).DOI
- [25]C. X. Quintela, F. Rivadulla, and J. M. Rivas, Thermoelectric Properties of Stoichiometric and Hole-Doped CrN, Appl. Phys. Lett. 94, (2009).DOI
- [26]F. Rivadulla et al., Reduction of the Bulk Modulus at High PressureinCrN, Nat. Mater. 8, 947 (2009).DOI
- [27]G. Kresse and J. Hafner, Ab Initio Molecular Dynamics for Liquid Metals, Phys. Rev. B 47, 558 (1993).
- [28]G. Kresse and J. Furthmüller, Efficiency of Ab-Initio Total Energy Calculations for Metals and Semiconductors Using a Plane-Wave Basis Set, Comput. Mater. Sci. 6, 15 (1996).DOI
- [29]S. Dudarev and G. Botton, Electron-Energy-Loss Spectra and the Structural Stability of Nickel Oxide: An LSDA+U Study, Phys. Rev. B - Condens. Matter Mater. Phys. 57, 1505 (1998).DOI
- [30]K. Momma and F. Izumi, VESTA 3 for Three-Dimensional Visualization of Crystal, Volumetric and Morphology Data, J. Appl. Crystallogr. 44, 1272 (2011).DOI
- [31]A. M Ganose, A. J Jackson, and D. O Scanlon, Sumo: Command-Line Tools for Plotting and Analysis of Periodic Ab Initio Calculations, J. Open Source Softw. 3, 717 (2018).DOI
- [32]P. Ström and D. Primetzhofer, Ion Beam Tools for Nondestructive In-Situ and in-Operando Composition Analysis and Modification of Materials at the Tandem Laboratory in Uppsala, J. Instrum. 17, (2022).DOI
- [33]M. Mayer, SIMNRA User’s Guide, Max-Planck-Institut Für Plasmaphys. Garching, Ger. Report IPP, (1997).
- [34]K. Arstila et al., Potku – New Analysis Software for Heavy Ion Elastic Recoil Detection Analysis, Nucl. Instruments Methods Phys. Res. Sect. B Beam Interact. with Mater. Atoms 331, 34 (2014).DOI
- [35]B. Xin, A. Le Febvrier, L. Wang, N. Solin, B. Paul, and P. Eklund, Growth and Optical Properties of CaxCoO2 Thin Films, Mater. Des. 210, 110033 (2021).DOI
- [36]A. S. Botana, F. Tran, V. Pardo, D. Baldomir, and P. Blaha, Electronic Structure of CrN: A Comparison between Different Exchange Correlation Potentials, Phys. Rev. B - Condens. Matter Mater. Phys. 85, 1 (2012).DOI
- [37]L. Zhou, K. Fritz, D. Holec, M. Bartosik, and B. Grabowski, Structural Stability and Thermodynamics of CrN Magnetic Phases from Ab Initio Calculations and Experiment, Phys. Rev. B 184102, 1 (2014).
- [38]B. Alling, T. Marten, and I. A. Abrikosov, Effect of Magnetic Disorder and Strong Electron Correlations on the Thermodynamics of CrN, Phys. Rev. B - Condens. Matter Mater. Phys. 82, 1 (2010).DOI
- [39]L. M. Corliss, N. Elliott, and J. M. Hastings, Antiferromagnetic Structure of CrN, Phys. Rev. 117, 929 (1960).DOI
- [41]J. E. G. and I. P. D. Gall, C.-S. Shin, T. Spila, M. Ode´n, M. J. H. Senna, Growth of Single-Crystal CrN on MgO(001): Effects of Low- Energy Ion-Irradiation on Surface Morphological Evolution and Physical Properties, J. Appl. Phys. 91, 3589 (2002).DOI
- [42]A. Le Febvrier, D. Gambino, F. Giovannelli, B. Bakhit, S. Hurand, G. Abadias, B. Alling, and P. Eklund, P -Type Behavior of CrN Thin Films via Control of Point Defects, Phys. Rev. B 105, 1 (2022).
- [43]P. A. Stampe, M. Bullock, W. P. Tucker, and R. J. Kennedy, Growth of MgO Thin Films on M-, A-, C- and R-Plane Sapphire by Laser Ablation, J. Phys. D. Appl. Phys. 32, 1778 (1999).DOI
- [44]M. A. Gharavi, G. Greczynski, F. Eriksson, J. Lu, B. Balke, D. Fournier, A. le Febvrier, C. Pallier, and P. Eklund, Synthesis and Characterization of Single-Phase Epitaxial Cr2N Thin Films by Reactive Magnetron Sputtering, J. Mater. Sci. 54, 1434 (2019).DOI
- [45]M. A. Gharavi, D. Gambino, A. le Febvrier, F. Eriksson, R. Armiento, B. Alling, and P. Eklund, High Thermoelectric Power Factor of Pure and Vanadium-Alloyed Chromium Nitride Thin Films, Mater. Today Commun. 28, 102493 (2021).DOI
- [46]B. Biswas, S. Chakraborty, O. Chowdhury, D. Rao, A. I. K. Pillai, V. Bhatia, M. Garbrecht, J. P. Feser, and B. Saha, In-Plane Cr2 N-CrN Metal-Semiconductor Heterostructure with Improved Thermoelectric Properties, Phys. Rev. Mater. 5, 1 (2021).