betaFeedback

WorksPhysics and Astronomy

Silicon nitride on-chip C-band spontaneous emission generation based on lanthanide doped microparticles

Abstract

The integration of active light-emitting elements into planar photonic circuits on a silicon nitride platform remains challenging due to material incompatibilities and high-temperature processing. Proposed hybrid method embeds monodisperse luminescent particles into lithographically defined wells above a 200 nm-thick silicon nitride taper coupler. A fabrication process involving wells etching, particle deposition, and planarization enables precise integration while maintaining waveguide integrity. When pumped at 950 nm with a diode laser, the device emits broadband radiation in the 1500-1600 nm range, covering the optical telecommunication C-band. Numerical simulations yield an average coupling efficiency of 0.25% into the fundamental waveguide mode, suggesting significant potential for further device optimization. The approach provides a scalable route for integrating broadband telecommunications emitters on a silicon nitride platform.

Introduction

Nowadays, research and development in the field of active and passive elements for planar photonics remain highly relevant [1, 2], driven by significant technological breakthroughs in the fabrication of high-quality materials. One of the promising platforms for planar photonics is silicon nitride: this material, paired with silicon dioxide, enables low intrinsic losses [3, 4, 5] compared to other widely used platforms such as InP [6, 7, 8], GaAs [9], and SOI [10]. The fabrication technology for silicon nitride-based planar photonic elements is well-established and has been implemented in a variety of devices [11, 12, 13, 14, 15] [16]. However, a critical technological challenge persists in integrating active elements such as photodiodes, amplifiers, and photodetectors into silicon nitride-based planar photonic chips. This challenge arises primarily from the incompatibility of silicon nitride with active elements operating in the near-infrared telecommunications band (C-band) and from the high-temperature annealing processes (∼1300∘C\sim1300^\circ\mathrm{C}) required during waveguide fabrication. Current solutions for integrating active elements into silicon nitride planar optical structures typically rely on hybrid assembly methods [17].

In this work, we propose a technology for creating a C-band spontaneous emission generator integrated into a planar waveguide, operating on the principle of light down-conversion. The active material consists of luminescent particles based on NaYF4\mathrm{NaYF}_{4} doped with erbium and ytterbium. Recently, such particles have found broad applications in bioimaging, biodiagnostics [18, 19, 20, 21], chemical sensing [22], and in creating new gain media in planar photonic amplifiers [23, 24, 25] and lasers [26, 27]. These particles exhibit a broad emission spectrum: upon absorbing light in the 900–1000 nm range [28, 29], they emit in the visible and near-infrared (C-band, 1530–1565 nm) regions, attributed to the rich energy structure of erbium ions [30, 31]. While there is an extensive class of infrared luminescent materials [32, 33, 34, 35, 36], their integration using microelectronic standards presents significant challenges. The NaYF4\mathrm{NaYF}_{4}:Yb,Er particles employed here are usually monodisperse in size, which is crucial for precise integration. Recent work by Asharchuk et al. [37] demonstrated the feasibility of large-scale “printing” of these particles on substrates up to 100 mm in diameter.

This approach enables the precise placement of luminescent microparticles at designated wells above nanophotonic structures fabricated in silicon nitride. To date, few attempts have been made to combine silicon nitride platforms with such particles due to the technological complexity of integration. In Ref. [38], a silicon nitride slot waveguide filled with PMMA containing fluoride particles was proposed to enhance active medium and waveguide coupling. Here, we present a design based on a circular-sector-shaped taper with luminescent particles deposited above. We have fabricated this device and demonstrated its functionality by coupling of particle emission into the waveguide.

Results and Discussion

Luminescent properties of particles

We started with examination of the luminescent characteristics of the synthesized monodisperse NaYF4:Yb3+,Er3+\mathrm{NaYF}_{4}:\mathrm{Yb}^{3+},\mathrm{Er}^{3+} microparticles fabricated using the methodology described in Asharchuk et al. [37]. A scanning electron micrograph (SEM) of the particles deposited on a silicon substrate is shown in Figure 1a. Luminescence spectroscopy was performed on individual particles; Figure 1b displays the luminescence spectrum of the NaYF4:Er,Yb\mathrm{NaYF}_{4}:\mathrm{Er},\mathrm{Yb} particles under 975 nm laser excitation. One can note from the plot that these particles exhibit intense emission bands in both the visible and infrared regions; in the present work, we focus on their near-infrared emission. The peak emission intensity in the infrared regime occurs at 1532 nm, with a full width at half maximum (FWHM) of 60 nm, as illustrated in the inset of Figure 1b.

Figure 1. Luminescence of the individual particles. (a) Scanning electron micrograph of particles deposited on a silicon substrate for luminescence studies. (b) Measured photoluminescence spectrum of the luminescent particles. The inset shows the near-infrared spectral region, highlighting the emission peak and linewidth. Optical telecommunication bands are denoted by the letters ’S’, ’C’, and ’L’, and highlighted by blue, green, and pink color boxes correspondingly.

Chip fabrication

The photon chip designed to couple the luminescence emission from microparticles with the waveguide composed of a taper of a circular sector shape with a radius of 48 μm48\,\mu\mathrm{m} and an opening angle of 40∘40^\circ, which transitioned into 1.4 μ\mum-width waveguide. Luminescent particles NaYF4:Yb3+,Er3+\mathrm{NaYF}_{4}:\mathrm{Yb}^{3+},\mathrm{Er}^{3+} were deposited on the rear area of the taper, as it can be seen in Figure 2b. The sample was fabricated on a silicon wafer. The fabrication process, similar to that described in Mumlyakov et al. [39], included thermal oxidation of silicon to form a silicon dioxide layer, deposition of a silicon nitride layer, patterning of the waveguide and taper from the silicon nitride layer, passivation with silicon dioxide, and incorporation of particles atop the lithographic pattern. The lateral dimensions of most particles lie in range of 1.5–2 μ\mum, with heights of 0.7–0.9 μ\mum [37]; therefore, the particle well area depth was set to 1 μ\mum. Within the well region, particles were distributed upon deposition according to the hexagonal close-packing principle. To increase output emission collection efficiency, a 500 μ\mum-long taper narrowing to 0.5 μ\mum at the chip facet was formed at the end of the waveguide. Figure 2a presents the sequence of 13 primary technological steps, demonstrating the process of fabricating planar waveguides and couplers with integrated microparticles. The manufacturing steps were performed in the following order: preparation of the silicon wafer for thermal oxidation; thermal oxidation of the wafer in water vapor at 950°C, achieving a 4 μ\mum thick silicon dioxide layer; deposition of a 200 nm silicon nitride film by plasma-enhanced chemical vapor deposition (PECVD) followed by annealing at 1150°C for 8 hours; patterning of the waveguide and coupler using electron-beam lithography (EBL) followed by reactive ion etching in a C4F8\mathrm{C}_{4}\mathrm{F}_{8}/Ar gas mixture; deposition of an upper silicon dioxide buffer layer by PECVD followed by planarization; application of photoresist and foration of the well region for NaYF4\mathrm{NaYF}_{4}:Er,Yb microparticles; development of the photoresist; dry etching of silicon dioxide to a depth of 1 μ\mum to form the well region; plasma removing of the photoresist; filling of the well region with particles according to the method described in [37]; deposition of silicon dioxide by PECVD for particle passivation followed by planarization; deposition of a nickel hardmask for deep etching of the multilayer structure to form the chip facet. After facet formation, the nickel layer was removed.

Figure 2. Fabrication of the chip with luminescent particles. a) Fabrication workflow. 1. Preparation of the silicon wafer for thermal oxidation; 2. wafer thermal oxidation in water vapor; 3. silicon nitride deposition and annealing; 4. EBL patterning and dry etching of the waveguide and coupler; 5. PECVD deposition and planarization of an upper SiO2_2 layer; 6. photoresist deposition and particles well region formation; 7. photoresist development; 8. SiO2_2 dry etching; 9. plasma removing of the photoresist; 10. filling the well region with particles according to [37]; 11. PECVD and planarization of an upper SiO2_2 layer; 12. nickel mask deposition for deep etching of the multilayer structure to form the chip facet; 13. schematic cross-section of the chip, showing its internal structure. b) Optical micrograph of the resulting planar taper structure with deposited microparticles. The red dashed line indicates the path of the focused ion beam cutting. c) SEM cross-section of the structure with layer indications. d) Energy-dispersive X-ray spectroscopy (EDAX) maps corresponding to the elemental peaks.

After fabricating the chip and performing all optical measurements, described below, we examined the internal structure of the sample by analyzing a cross-section created via focused ion beam milling, followed by investigation of the coupler region using scanning electron microscopy and energy-dispersive X-ray spectroscopy (EDAX). The results are presented in Figure 2c,Figure 2d. As seen in the figure, the elemental composition of the cross-section layers matches the design: a 4 μ\mum silicon dioxide layer, a 200 nm silicon nitride layer, a 730 nm NaYF4\mathrm{NaYF}_{4}:Yb,Er particle layer, and a 0.52 μ\mum silicon dioxide layer.

Optical measurements and calculations

After fabrication of the photonic chip, we measured the power of the luminescent emission from the particles that coupled into the waveguide after propagating through the coupler. The measurement setup scheme is shown in Figure 3. A fiber-coupled semiconductor laser diode emitting at a wavelength of 950 nm was employed for particle excitation. The excitation system comprised a fiber collimator C1, an optical filter to suppress the diode’s satellite lines, a dichroic mirror, and a focusing objective with numerical aperture NA = 0.8. The excitation spot on the sample was 30 μ\mum in diameter, fully covering all particles deposited on the taper. Emission coupled into the waveguide was collected at the opposite chip facet using an objective with NA = 0.5. After that, the collected emission passed through a filter set to remove residual pump light and was directed either to an infrared camera (SWIR1300KMA, ToupTek, China) or into fiber collimator C2, which was connected to a spectrometer (Optosky, China).

Figure 3. Experimental setup. L1–L5: lenses; C1, C2: fiber collimators; LED — illumination; BS — beam splitter; SP filter — short-pass filter. Insets: the optical micrograph of the taper with visible upconversion emission taken through the pump arm, the NIR image of the emission spot at the chip output, and the illustration of the pump and collection geometry.

We recorded emission power spectra transmitted through the waveguide and collection optics at various pump powers. The results are presented in Figure 4. As seen in Figure 4a, the peak spectral power reaches 0.8 pW/nm at approximately 1530 nm, the spectral full width at half maximum is ∼\sim 60 nm, and the total integrated power is 48 ±\pm 2 pW according to the results of peak approximation. The dependence of luminescence power on pump power, shown in Figure 4b, exhibits the characteristic saturation behavior of down-conversion luminescence. The data were fitted to the saturation model Plum(Ppump)=Pmax⁡Ppump/(Ppump+Psat)P_{\mathrm{lum}}(P_{\mathrm{pump}})=P_{\max}P_{\mathrm{pump}}/(P_{\mathrm{pump}}+P_{\mathrm{sat}}), where PlumP_{\mathrm{lum}} is the luminescence power, PpumpP_{\mathrm{pump}} the pump power, Pmax⁡P_{\max} the maximal luminescence power, and PsatP_{\mathrm{sat}} the saturation pump power. We obtained Pmax⁡=P_{\max}= 52.0±1.552.0 \pm1.5 pW and Psat=51±5P_{\mathrm{sat}} = 51 \pm5 mW, corresponding to a pump intensity of 7.2×1037.2 \times10^{3} W/cm2^{2}.

Figure 4. Emission coupling into the waveguide. a) Spectral power of luminescent emission at the chip output. Gray curve: experimental data; green bell: Gaussian fit. PtotalP_{\mathrm{total}} denotes the integrated power over the specified range. b) Integrated luminescence power at the chip output as a function of excitation power. Markers: experimental data; solid curve: saturation-law fit. Pmax⁡P_{\max} and PsatP_{\mathrm{sat}} denote maximum luminescence power and saturation power, respectively.

To evaluate the coupling efficiency of the device, we performed numerical simulations of emission coupling into the waveguide mode using the finite-difference time-domain (FDTD) method. The luminescent particles were modeled as incoherent dipole sources. Given the excitation geometry, we assume the dipole moments lie predominantly in the prism base plane of the particles [40]. Thus, the main contribution arises from dipoles oriented in the same plane, perpendicular to the waveguide, coupling primarily into the TE mode. In our simulations, only this dipole polarization and the TE mode were considered. The simulated structure geometry matched that of the fabricated chip; the simulation schematic is shown in Figure 5a. The dipole source was scanned across the particle coordinates, and transmission into fundamental TE mode was collected. The resulting transmission of dipole emission into the fundamental TE waveguide mode, averaged over all source positions, is plotted in Figure 5b. The mean transmission is approximately −26 dB (0.25%), with the highest contributions from sources nearest to the taper. To illustrate this, we averaged transmission over xx, yy coordinates to obtain its dependence on dipole height. The result, shown in Figure 5c, reveals an exponential decay of coupling efficiency with increasing distance between the dipole and the structure surface. This observation highlights the general challenge of efficient emission coupling into a waveguide: significant spatial overlap between the particle emission field and the guided mode is required.

Figure 5. Simulation of particle emission coupling into the waveguide mode. a) Simulation schematic. b) Transmission from a dipole source into the TE mode, averaged over the luminescent particle positions shown in (a). c) Averaged transmission as a function of dipole source height.

To further enhance device performance, several optimization strategies can be considered. Tailoring the taper geometry, for instance, by adjusting the opening angle or introducing a multi-stage taper, could improve spatial mode matching and increase coupling efficiency. Improving the passivation technology could decrease the scattering losses, induced by surface roughness. Engineering of the particle distribution, including controlled variation of particle density and orientation, can optimize local dipole alignment relative to the waveguide modes. Finally, integrating a resonant cavity or photonic crystal structure in the taper region may provide Purcell-enhanced emission and directional coupling.

Conclusion

In this work, we demonstrate the experimental realization of a planar integrated spontaneous emission generator in the C-band based on monodisperse microparticles NaYF4:Yb,Er\mathrm{NaYF}_{4}:\mathrm{Yb},\mathrm{Er} embedded in a silicon nitride photonic structure. The developed particle deposition and passivation technology enables reliable fixation of the particles over the coupler, ensuring their uniform distribution and optical coupling to the fundamental TE–mode. Experimentally, we show that pumping at 950 nm with a semiconductor laser successfully couples intense emission into the waveguide, with a peak at 1530 nm, a spectral width of 60 nm (FWHM), and an integrated power of 48±248 \pm2 pW at the chip output. Numerical FDTD simulations demonstrate that the coupling efficiency of upconversion dipole emitters into the TE–mode is on the order of 0.25%. Further optimization of the structural parameters has the potential to yield more efficient spontaneous emission generators. The proposed approach opens prospects for creating active elements on the silicon nitride platform without complex hybrid assemblies: integrated microparticles can serve as broadband emission sources in the telecommunications range, amplify signals in planar amplifiers, and act as the gain medium for microlasers.

Acknowledgements

The study has been carried out with the support of project No. 125020501540-9 of the Ministry of Education and Science of the Russian Federation. Fabrication and technology characterization were carried out at large scale facility complex for heterogeneous integration technologies and silicon + carbon nanotechnologies.

Conflict of Interests

The authors declare no conflict of interest.

References

  1. [1]C. Xiang, W. Jin, and J. E. Bowers, “Silicon nitride passive and active photonic integrated circuits: trends and prospects,” Photonics Research, vol. 10, p. A82, June 2022.DOI
  2. [2]H. Tian, A. G. Attanasio, A. Siddharth, A. Voloshin, V. Snigirev, G. Lihachev, A. Bancora, V. Shadymov, R. N. Wang, J. Reimersenberger, T. J. Kippenberg, and S. A. Bhave, “Programmable Silicon Nitride Photonic Integrated Circuits,” in 2023 IEEE 36th International Conference on Micro Electro Mechanical Systems (MEMS), (Munich, Germany), pp. 149–152, IEEE, Jan. 2023.DOI
  3. [3]F. Gardes, A. Shooa, G. De Paoli, I. Skandalos, S. Ilie, T. Rutirawut, W. Talataisong, J. Faneca, V. Vitali, Y. Hou, T. D. Bucio, I. Zeimpekis, C. Lacava, and P. Petropoulos, “A Review of Capabilities and Scope for Hybrid Integration Offered by Silicon-Nitride-Based Photonic Integrated Circuits,” Sensors, vol. 22, p. 4227, June 2022.DOI
  4. [4]J. Guo, G. A. Vawter, M. J. Shaw, G. R. Hadley, P. Esherick, A. Jain, C. R. Alford, and C. T. Sullivan, “Characterization of Si₃N₄/SiO₂ planar lightwave circuits and ring resonators,” in Optical Components and Materials (M. J. F. Dignonet and S. Jiang, eds.), vol. 5350, pp. 13 – 22, International Society for Optics and Photonics, SPIE, 2004.
  5. [5]M.-C. Tien, J. F. Bauters, M. J. R. Heck, D. J. Blumenthal, and J. E. Bowers, “Ultra-low loss Si₃N₄ waveguides with low nonlinearity and high power handling capability,” Optics Express, vol. 18, p. 23562, Nov. 2010.DOI
  6. [6]L. M. Augustin, R. Santos, E. Den Haan, S. Kleijn, P. J. A. Thijs, S. Latkowski, D. Zhao, W. Yao, J. Bolk, H. Ambrosius, S. Mingaleev, A. Richter, A. Bakker, and T. Korthorst, “InP-Based Generic Foundry Platform for Photonic Integrated Circuits,” IEEE Journal of Selected Topics in Quantum Electronics, vol. 24, pp. 1–10, Jan. 2018.DOI
  7. [7]M. Smith, K. Williams, and J. Van Der Tol, “Past, present, and future of InP-based photonic integration,” APL Photonics, vol. 4, p. 050901, May 2019.
  8. [8]J. Van Der Tol, Y. Oei, U. Khalique, R. Nötzel, and M. Smit, “InP-based photonic circuits: Comparison of monolithic integration techniques,” Progress in Quantum Electronics, vol. 34, pp. 135–172, July 2010.DOI
  9. [9]J.-P. Koester, H. Wenzel, J. Fricke, M. Reggentin, P. Della Casa, P. Sammeta, O. Brox, M. Ekterai, M. Kohlbrenner, A. Renkewitz, C. Zink, T. Tenzler, J. Boschker, M. Weyers, and A. Knigge, “GaAs-based photonic integrated circuit platform enabling monolithic ring-resonator-coupled lasers,” APL Photonics, vol. 9, p. 106102, Oct. 2024.DOI
  10. [10]Z. Yan, Y. Han, L. Lin, Y. Xue, C. Ma, W. K. Ng, K. S. Wong, and K. M. Lau, “A monolithic InP/SOI platform for integrated photonics,” Light: Science & Applications, vol. 10, p. 200, Sept. 2021.DOI
  11. [11]S. Romero-García, F. Merget, F. Zhong, H. Finkelstein, and J. Witzens, “Silicon nitride CMOS-compatible platform for integrated photonics applications at visible wavelengths,” Optics Express, vol. 21, p. 14036, June 2013.
  12. [12]W. D. Sacher, Y. Huang, G.-Q. Lo, and J. K. S. Poon, “Multilayer Silicon Nitride-on-Silicon Integrated Photonic Platforms and Devices,” Journal of Lightwave Technology, vol. 33, pp. 901–910, Feb. 2015.DOI
  13. [13]H. Xu, Z. Shu, N. Li, Y. Shen, B. Ji, Y. Yang, T. Wu, M. Long, and G. He, “Frequency-Dependent Squeezing via Einstein–Podolsky–Rosen Entanglement Based on Silicon Nitride Microring Resonators,” Advanced Quantum Technologies, p. 2400473, Dec. 2024.arxiv.org/abs/2409.09336
  14. [14]K. A. Buzaverov, A. S. Baburin, E. V. Sergeev, S. S. Avdeev, E. S. Lotkov, S. V. Bukatin, I. A. Stepanov, A. B. Kramarenko, A. S. Amiraslanov, D. V. Kushnev, I. A. Ryzhikov, and I. A. Rodionov, “Silicon Nitride Integrated Photonics from Visible to Mid-Infrared Spectra,” Laser & Photonics Reviews, vol. 18, p. 2400508, Dec. 2024.arxiv.org/abs/2405.10038
  15. [15]D. Belogolovskii, M. M. Rahman, K. Johnson, V. Fedorov, A. Grieco, N. Alic, A. Ndao, P. K. L. Yu, and Y. Fainman, “Large Bidirectional Refractive Index Change in Silicon-rich Nitride via Visible Light Trimming,” Advanced Optical Materials, vol. 13, p. 2403420, May 2025. N. Kumar, Y. Liang, N. LiCausi, D. Llewellyn, K. Lokovic, M. Lovelady, V. R. Manfrinato, A. Melnichuk, G. Mendoza, B. Moores, S. Mukherjee, J. Munns, F.-X. Musalem, F. Najafi, J. L. O’Brien, J. E. Ortmann, S. Pai, B. Park, H.-T. Peng, N. Penthorn, B. Peterson, G. Peterson, M. Poush, G. J. Pryde, T. Ramprasad, G. Ray, A. V. Rodriguez, B. Roxworthy, T. Rudolph, D. J. Saunders, P. Shadbolt, D. Shah, A. Bahgat Shehata, H. Shin, J. Sinsky, J. Smith, B. Sohn, Y.-I. Sohn, G. Son, M. C. M. M. Souza, C. Sparrow, M. Staffaroni, C. Stavrakas, V. Sukumaran, D. Tamborini, M. G. Thompson, K. Tran, M. Triplett, M. Tung, A. Veitia, A. Vert, M. D. Vidrighin, I. Vorobeichik, P. Weigel, M. Wingert, J. Wooding, and X. Zhou, “A manufacturable platform for photonic quantum computing,” Nature, Feb. 2025.
  16. [17]Y. Zhu, Y. Zhao, and L. Zhu, “Loss induced coherent combining in InP-Si₃N₄ hybrid platform,” Scientific Reports, vol. 8, p. 878, Jan. 2018.DOI
  17. [18]V. Oleska, H. Macková, H. Engstová, V. Patsula, O. Shapoval, N. Velychkivska, P. Ježek, and D. Horák, “Poly(N,N-dimethylacrylamide)-coated upconverting NaYF₄:Yb,Er@NaYF₄:Nd core-shell nanoparticles for fluorescent labeling of carcinoma cells,” Scientific Reports, vol. 11, p. 21373, 2021.
  18. [19]X. Cui, D. Mathe, N. Kovács, I. Horváth, M. Jauregui-Osoro, R. Torres Martin de Rosales, G. E. D. Mullen, W. Wong, Y. Yan, D. Krüger, A. N. Khlobystov, M. Gimenez-Lopez, M. Semjeni, K. Szigeti, D. S. Veres, H. Lu, I. Hernández, W. P. Gillin, A. Protti, K. K. Petik, M. A. Green, and P. J. Blower, “Synthesis, Characterization, and Application of Core–Shell Co₀.₁₆Fe₂.₈₄O₄@NaYF₄(Yb, Er) and Fe₃O₄@NaYF₄(Yb, Tm) Nanoparticle as Trimodal (MRI, PET/SPECT, and Optical) Imaging Agents,” Bioconjugate Chemistry, vol. 27, pp. 319–328, Feb. 2016. Publisher: American Chemical Society.DOI
  19. [20]J. Chen, C. Guo, M. Wang, L. Huang, L. Wang, C. Mi, J. Li, X. Fang, C. Mao, and S. Xu, “Controllable synthesis of NaYF₄:Yb,Er upconversion nanophosphors and their application to in vivo imaging of Caenorhabditis elegans,” Journal of Materials Chemistry, vol. 21, no. 8, p. 2632, 2011.pubmed.ncbi.nlm.nih.gov/21666862
  20. [21]P. Reineck and B. C. Gibson, “Near-Infrared Fluorescent Nanomaterials for Bioimaging and Sensing,” Advanced Optical Materials, vol. 5, p. 1600446, Jan. 2017.DOI
  21. [22]S. Abbasi-Moayed, A. Bigdeli, and M. R. Hormozi-Nezhad, “Application of NaYF₄:Yb/Er/Tm UCNPs in Array-Based Sensing of Neurotransmitters: From a Single Particle to a Multichannel Sensor Array,” ACS Applied Materials & Interfaces, vol. 12, pp. 52976–52982, Nov. 2020.
  22. [23]M. Zhang, W. Zhang, F. Wang, D. Zhao, C. Qu, X. Wang, Y. Yi, E. Cassan, and D. Zhang, “High-gain polymer optical waveguide amplifiers based on core-shell NaYF₄/NaLuF₄:Yb³⁺, Er³⁺ NPs-PMMA covalent-linking nanocomposites,” Scientific Reports, vol. 6, p. 36729, 2016.DOI
  23. [24]Z. Zhou, J. Xue, B. Zhang, C. Wang, X. Yang, W. Fan, L. Ying, Z. Zheng, Y. Xie, Y. Wu, X. Yang, and D. Zhang, “Optical gain based on NaYF4: Er³⁺, Yb³⁺ nanoparticles-doped polymer waveguide under convenient LED pumping,” Applied Physics Letters, vol. 118, p. 173301, Apr. 2021.DOI
  24. [25]Y. Yang, F. Wang, S. Ma, M. Zhou, Y. Liang, G. Qin, D. Zhang, W. Qin, D. Zhao, and X. Zhang, “Great enhancement of relative gain in polymer waveguide amplifier using NaYF₄/NaLuF₄:Yb,Er-PMMA nanocomposite as gain media,” Polymer, vol. 188, p. 122104, Feb. 2020.DOI
  25. [26]T. Sun, B. Chen, Y. Guo, Q. Zhu, J. Zhao, Y. Li, X. Chen, Y. Wu, Y. Gao, L. Jin, S. T. Chu, and F. Wang, “Ultralarge anti-Stokes lasing through tandem upconversion,” Nature Communications, vol. 13, p. 1032, Feb. 2022.DOI
  26. [27]B.-S. Moon, T. K. Lee, W. C. Jeon, S. K. Kwak, Y.-J. Kim, and D.-H. Kim, “Continuous-wave upconversion lasing with a sub-10 w cm⁻² threshold enabled by atomic disorder in the host matrix,” Nature Communications, vol. 12, p. 4437, July 2021.DOI
  27. [28]Q. Wang, M. C. Tan, R. Zhuo, G. A. Kumar, and R. E. Riman, “A Solvothermal Route to Size- and Phase-Controlled Highly Luminescent NaYF₄:Yb,Er Up-Conversion Nanocrystals,” Journal of Nanoscience and Nanotechnology, vol. 10, pp. 1685–1692, Mar. 2010.pubmed.ncbi.nlm.nih.gov/20355558
  28. [29]M. Gunaseelan, S. Yamini, G. A. Kumar, D. K. Sardar, and J. Senthilselvan, “Reverse microemulsion synthesis of mixed α and β phase NaYF₄:Yb,Er nanoparticles: calcination induced phase formation, morphology, and upconversion emission,” Journal of Sol-Gel Science and Technology, vol. 96, pp. 550–563, Dec. 2020.DOI
  29. [30]A. Nadort, J. Zhao, and E. M. Goldys, “Lanthanide upconversion luminescence at the nanoscale: fundamentals and optical properties,” Nanoscale, vol. 8, no. 27, pp. 13099–13130, 2016.DOI
  30. [31]X. Zhai, J. Li, S. Liu, X. Liu, D. Zhao, F. Wang, D. Zhang, G. Qin, and W. Qin, “Enhancement of 1.53 μm emission band in NaYF₄:Er³⁺,Yb³⁺,Ce³⁺ nanocrystals for polymer-based optical waveguide amplifiers,” Optical Materials Express, vol. 3, p. 270, Feb. 2013.
  31. [32]X. Zhang, P. Dai, and D. Wen, “Ultra-broadband of up to 200 nm near-infrared phosphors based on one-site occupation strategy for multipurpose applications in light-emitting diodes,” Ceramics International, vol. 49, pp. 4881–4888, Feb. 2023.DOI
  32. [33]Z. Chen, L. Liu, F. Yuan, Y. Huang, L. Zhang, and Z. Lin, “Broadening of the near-infrared emission band of the Mg₂ Al₄ Si₅ O₁₈ :Cr³⁺ phosphor for illumination emission applications,” Journal of Materials Chemistry C, vol. 11, no. 42, pp. 14787–14795, 2023.
  33. [34]C. Cong, Z. Wang, J. Wang, X. Wang, X. Xue, and X. Wang, “A novel broadband near-infrared phosphor NaBaScSi₂O₇:Fe³⁺ and its application in pc-LED and night vision,” Science China Materials, vol. 68, pp. 1074–1081, Apr. 2025.
  34. [35]T. Gao, Y. Liu, R. Liu, and W. Zhuang, “Research Progress and Development of Near-Infrared Phosphors,” Materials, vol. 16, p. 3145, Apr. 2023.DOI
  35. [36]V. Rajendran, H. Chang, and R.-S. Liu, “(INVITED) Recent progress on broadband near-infrared phosphors-converted light emitting diodes for future miniature spectrometers,” Optical Materials: X, vol. 1, p. 100011, Jan. 2019.DOI
  36. [37]I. Asharchuk, N. Vovk, I. Filippov, M. Shibalov, A. Mumlyakov, G. Diudbin, Y. Anufriev, and M. Tarkhov, “Planar technology fabrication of high-density luminescence structure based on NaYF₄ microparticles,” Optical Materials, vol. 150, p. 115304, Apr. 2024.DOI
  37. [38]X. Liu, M. Zhang, and G. Hu, “Gain Enhancement of the Optical Waveguide Amplifier Based on NaYF₄/NaLuF₄: Yb, Er NPs-PMMA Integrated with a Si₃N₄ Slot,” Nanomaterials, vol. 12, p. 2937, Aug. 2022.DOI
  38. [39]A. M. Mumlyakov, N. Y. Dmitriev, M. V. Shibalov, I. A. Filippov, I. V. Trofimov, A. N. Danilin, V. E. Lobanov, I. A. Bilenko, and M. A. Tarkhov, “Void-free upper cladding deposition process for low-loss integrated silicon nitride photonics,” Physical Review Applied, vol. 22, p. 054027, Nov. 2024.DOI
  39. [40]K. K. Green, J. Wirth, and S. F. Lim, “Nanoplasmonic Upconverting Nanoparticles as Orientation Sensors for Single Particle Microscopy,” Scientific Reports, vol. 7, p. 762, Apr. 2017.DOI

Paper details

vlnc:W_ghbeb8yn
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents