betaFeedback

WorksComputer Science

Input-output characterization of robotic grasping: Connecting design parameters to grasp behavior through the admittance

Abstract

Low-impedance grippers make the dynamics of a grasp matter. Current grasp metrics, however, are static: they describe how a held object resists constant loads, not how it responds to time-varying ones. To quantify this, we rely on small-signal analysis to characterize a grasp by its admittance, the transfer matrix relating load perturbations to object displacements around an equilibrium. This transfer matrix recovers the stiffness and stability of the grasp at zero frequency and captures its natural frequencies and peak gain under time-varying loads. We apply this characterization to a planar two-finger gripper under proportional-derivative control. We show that two grasps of the same object in the same position and with the same contact forces can differ in stiffness by two orders of magnitude. Likewise, two grasps that share the same stiffness can exhibit very different resonances. Nonlinear simulations confirm the effectiveness of our small-signal analysis in capturing the dynamic behavior of grasping.

Introduction

Grasping with low-impedance grippers is a dynamic problem. Compliance has long been recognized as useful in manipulation [1, 2, 3], but only recently have grippers started to implement it, thanks to advances in actuator design [4], low-inertia fingers [5], direct-drive actuation [6], and elastic elements [7, 8]. These grippers promote force transparency, high-bandwidth feedback, and fast, contact-rich motions, and thus challenge the long-standing treatment of grasping and manipulation as quasi-static problems [9]. Their low stiffness and friction also yield lightly damped resonances at low frequencies, which these motions can excite. Wimböck et al. [10] showed experimentally that the dynamics of such grippers should not be neglected.

Current grasp metrics, however, do not describe how a held object responds to time-varying loads. Standard criteria, such as the Ferrari–Canny ϵ\epsilon-metric [11] and stiffness-based quality measures [12], evaluate whether a hand can withstand arbitrary wrench disturbance magnitudes in static conditions. They treat finger links as massless and so neglect mechanical inertia, joint damping, and coupling resonances. Yet low-impedance grippers are designed for unstructured environments, where fast inertial perturbations and contact impacts are expected during standard manipulation, such as pushing or insertion. Dynamic metrics exist but address other questions, such as the accelerations a hand can impart to the object [13] or the outcome of grasp acquisition under pose uncertainty [14]. A tool is therefore needed to quantify

the response of a held object to time-varying loads, and to relate it to the gripper parameters, which include both the morphology parameters and the control parameters.

To quantify this response, we characterized a grasp by its admittance, H(s)=(Ms2+Ds+K)−1\mathbf{H}(s)=(\mathbf{M}s^2+\mathbf{D}s+\mathbf{K})^{-1}, the transfer matrix relating load perturbations to displacements of the grasped object around an equilibrium. In contrast to classical stiffness-based measures that relate static load perturbations to static displacements, the admittance includes inertia and damping, thereby capturing the full spectrum of time-varying perturbations. At zero frequency, the admittance recovers the stiffness; at nonzero frequencies, it reveals critical dynamic behavior, such as resonances, that quasi-static metrics miss. Crucially, the gripper parameters directly shape the admittance, establishing a connection between these design parameters and the grasp dynamics.

On a minimal gripper (Figure 1), we showed that grasps that are equivalent under static metrics can respond differently to fast load perturbations. Closed-form expressions are hard to derive in general without dropping terms that can destabilize the grasp [15]. We therefore considered a minimal model that keeps these terms and remains analytically tractable: a planar two-finger gripper under joint proportional-derivative (PD) control, holding a disk through rigid frictionless contacts. With this model, we also showed that the same gripper can hold an object in qualitatively different ways. Nonlinear simulations confirmed that the admittance, although derived from a linearization, predicts the main dynamic features of the nonlinear model.

Planar gripper model

Figure 1. Planar gripper model: the palm and the two fingers push on the disk along their normals, with the forces f0n0\mathbf{f}_0 n_0 and fini\mathbf{f}_i n_i, to balance the load F=(Fx,Fy)\mathbf{F}=(F_x,F_y) acting on the disk center c\mathbf{c}. Finger ii rotates about pi\mathbf{p}_i, and its angle qiq_i is measured from the xx direction, positive when closing. It touches the disk at ai\mathbf{a}_i, at distance ℓi\ell_i from its joint. A PD controller drives each finger toward the reference qref\mathbf{q}_{\mathrm{ref}}. The disk is drawn on the palm.

SymbolMeaningValue (nominal)
Gripper parameters: morphology
LLfinger length100 mm
ddhalf-distance between the joints40 mm
IfI_ffinger inertia about its joint6.7×10−5 kg m26.7 \times10^{-5}\ \mathrm{kg\,m^2}
Gripper parameters: control
kpk_pproportional gain1 N m rad−11\ \mathrm{N\,m\,rad^{-1}}
kdk_dderivative gain0.01 N m s rad−10.01\ \mathrm{N\,m\,s\,rad^{-1}}
qrefq_{\mathrm{ref}}joint reference20∘20^\circ, 90∘90^\circ
Disk and load
rr, mmdisk radius and mass30 mm, 100 g
F=(Fx,Fy)\mathbf{F}=(F_x,F_y)load(0.6 N, 0.0 N)
Variables
c=(cx,cy)\mathbf{c}=(c_x,c_y)disk center
qiq_i, eie_ifinger angle, error
τi\tau_ijoint torque
ℓi\ell_i, hih_icontact distance, distance along yy
ai\mathbf{a}_icontact point of finger ii
ti\mathbf{t}_i, ni\mathbf{n}_i, n0\mathbf{n}_0finger tangent and normal, palm normal
fi\mathbf{f}_i, f0\mathbf{f}_0finger force, palm force
gi\mathbf{g}_i, J\mathbf{J}transmission vector, Jacobian
VVcontroller potential
M\mathbf{M}, C\mathbf{C}, D\mathbf{D}, K\mathbf{K}inertia, Coriolis, damping, and stiffness matrices
H(s)H(s)admittance (load to displacement)
P(cx)P(c_x), σ(cx)\sigma(c_x)holding force, transmission
e∗(cx)e^*(c_x), κ\kappacritical error, normalized gain

Table 1. Parameters and variables.

Section II introduces the model used throughout the paper. Section III presents the input-output characterization of a grasp by its admittance, obtained by linearization. Section IV then derives the static equilibria and their stability. Section V studies the dynamic response, showing how the gripper parameters shape the admittance H(s)H(s) and how far this admittance predicts the nonlinear response. Finally, Section VI discusses the results and their limitations. The main symbols and the parameter values are summarized in Table I.

Gripper model and control

System description and assumptions

We consider a minimal model: a planar two-finger gripper holding a disk through rigid frictionless contacts, with a PD controller at each joint, as shown in Figure 1. In control theory, simple examples such as the inverted pendulum teach general principles. This model plays the same role for grasping. The model captures the contact geometry, the controller, and the inertia. It treats the fingers and the disk as rigid, and the contacts as rigid and frictionless, so that all the stiffness and the damping of the grasp come from the controller.

Gripper morphology: The gripper has two rigid single-link fingers of length LL, attached to a fixed palm by revolute joints. The joints are at distance dd from the center of the palm, and each finger has inertia IfI_f about its joint. The frame origin is the center of the palm, with xx pointing away from the palm and yy along it. Each finger angle qiq_i is measured from the xx direction, positive when closing, that is, clockwise for finger 1 and counterclockwise for finger 2.

Kinematics

Disk and load: The fingers hold a rigid disk of radius rr and mass mm, with center c=(cx,cy)\mathbf{c}=(c_x,c_y). We assume d>rd>r: otherwise the fingers lean outward to touch the disk, and their torque pushes it out of the gripper instead of holding it. An external load F=(Fx,Fy)\mathbf{F}=(F_x,F_y) acts on the disk center. Gravity is perpendicular to the plane of motion.

Contacts: The contacts are rigid, frictionless, and unilateral. The bodies cannot interpenetrate, so that cx≥rc_x\ge r, the contact forces act along the contact normals, and the fingers and the palm can only push on the disk. Each finger touches the disk on its side, not at its tip. Without friction, the contacts exert no torque on the disk, so its rotation is decoupled and not modeled.

Gripper controller: Both fingers track a common constant reference qrefq_{\mathrm{ref}} with independent PD controllers that share the proportional gain kp>0k_p>0 and the derivative gain kd>0k_d>0. The joint torques are

τi=kpei+kde˙i,(1)\tau_i = k_p e_i + k_d \dot{e}_i, \tag*{(1)}

where ei=qref−qie_i=q_{\mathrm{ref}}-q_i is the error of finger ii and e˙i=−q˙i\dot{e}_i=-\dot{q}_i.

Kinematics

We derive the relationship between the finger angles q=(q1,q2)\mathbf{q}=(q_1,q_2) and the disk position c\mathbf{c}. The finger angles follow from the tangency of each finger to the disk. Finger ii lies on the side νi\nu_i of the symmetry axis, with ν1=−1\nu_1=-1 and ν2=−1\nu_2=-1, and its joint is at pi=(0,νid)\mathbf{p}_i=(0,\nu_i d). Let ti\mathbf{t}_i be the unit vector along finger ii and ni\mathbf{n}_i the unit vector normal to this finger, pointing toward the disk, as shown in Figure 1. They are represented by

ti=(cos⁡qi−νisin⁡qi),ni=(−sin⁡qi−νicos⁡qi).(2)\mathbf{t}_i= \begin{pmatrix} \cos q_i\\ -\nu_i\sin q_i \end{pmatrix}, \qquad \mathbf{n}_i= \begin{pmatrix} -\sin q_i\\ -\nu_i\cos q_i \end{pmatrix}. \tag*{(2)}

Let ai=pi+ℓiti\mathbf{a}_i=\mathbf{p}_i+\ell_i\mathbf{t}_i be the contact point of finger ii, at distance ℓi\ell_i from its joint. Contact requires ℓi≤L\ell_i\le L. At ai\mathbf{a}_i, the radius of the disk is normal to the finger, so that

c−pi=ℓiti+rni.(3)\mathbf{c}-\mathbf{p}_i=\ell_i\mathbf{t}_i+r\mathbf{n}_i. \tag*{(3)}

With reference to Figure 2, let hi=d−νicyh_i=d-\nu_i c_y be the distance along yy between joint ii and the disk center. Since ti⊥ni\mathbf{t}_i\perp\mathbf{n}_i, the points pi\mathbf{p}_i, ai\mathbf{a}_i, and c\mathbf{c} form a right triangle with legs ℓi\ell_i and rr. The segment from pi\mathbf{p}_i to c\mathbf{c} is the hypotenuse of this triangle, and the right triangle with legs cxc_x and hih_i. Therefore, ℓi2+r2=cx2+hi2\ell_i^2+r^2=c_x^2+h_i^2. This segment makes the angle arctan⁡(hi/cx)\arctan(h_i/c_x) with the xx direction and the angle arctan⁡(r/ℓi)\arctan(r/\ell_i) with the finger. Hence,

Finger geometry for the derivation of the finger angle

Figure 2. The finger angle in (4) follows from two right triangles that share the dotted hypotenuse from p1\mathbf{p}_1 to c\mathbf{c} (finger 1, disk off the axis). The tangency triangle (blue) has legs ℓ1\ell_1 along t1\mathbf{t}_1 and rr along n1\mathbf{n}_1, with the right angle at the contact point a1\mathbf{a}_1. The other triangle (orange) has legs cxc_x and h1=d−cyh_1=d-c_y. The finger angle is the angle of the hypotenuse, arctan⁡(h1/cx)\arctan(h_1/c_x), minus ψ1=arctan⁡(r/ℓ1)\psi_1=\arctan(r/\ell_1).

ℓi=cx2+hi2−r2,qi=arctan⁡hicx−arctan⁡rℓi.(4)\ell_i=\sqrt{c_x^2+h_i^2-r^2}, \qquad q_i=\arctan\frac{h_i}{c_x}-\arctan\frac{r}{\ell_i}. \tag*{(4)}

The velocities follow from the contact condition. The point of finger ii at ai\mathbf{a}_i moves with velocity ℓiq˙ini\ell_i\dot{q}_i\mathbf{n}_i, in the normal direction. The contact is rigid but frictionless: the normal velocities of the finger and the disk must match, and their tangential velocities can differ. Matching the normal velocities, ℓiq˙i=niTc˙\ell_i\dot{q}_i=\mathbf{n}_i^{\mathsf{T}}\dot{\mathbf{c}}, gives

q˙i=giTc˙,gi=niℓi=∇qi.(5)\dot{q}_i=\mathbf{g}_i^{\mathsf{T}}\dot{\mathbf{c}}, \qquad \mathbf{g}_i=\frac{\mathbf{n}_i}{\ell_i}=\nabla q_i. \tag*{(5)}

where ∇qi=∂qi/∂c\nabla q_i=\partial q_i/\partial\mathbf{c} and the transmission vector gi=(gi,x,gi,y)\mathbf{g}_i=(g_{i,x},g_{i,y}) relates the velocity of the disk to that of finger ii. For both fingers, q˙=Jc˙\dot{\mathbf{q}}=\mathbf{J}\dot{\mathbf{c}}, with the Jacobian J=[g1 g2]T\mathbf{J}=[\mathbf{g}_1\ \mathbf{g}_2]^{\mathsf{T}}.

Dynamics

We derive the dynamics of the controlled gripper in the standard manipulator form. Let fi≥0f_i\geq0 be the magnitude of the force applied by finger ii on the disk, and f0≥0f_0\geq0 that of the palm, which acts along the palm normal n0=(1,0)\mathbf{n}_0=(1,0). Balancing forces and moments, we have

mc¨=F+f1n1+f2n2+f0n0,(6)m\ddot{\mathbf{c}}=\mathbf{F}+f_1\mathbf{n}_1+f_2\mathbf{n}_2+f_0\mathbf{n}_0, \tag*{(6)}
Ifq¨i=τi−ℓifi,i∈{1,2}.(7)I_f\ddot{q}_i=\tau_i-\ell_i f_i,\qquad i\in\{1,2\}. \tag*{(7)}

Solving (7) for fif_i and substituting it into (6) eliminates the finger forces. This step uses ni/ℓi=gi\mathbf{n}_i/\ell_i=\mathbf{g}_i and q¨=Jc¨+J˙c˙\ddot{\mathbf{q}}=\mathbf{J}\ddot{\mathbf{c}}+\dot{\mathbf{J}}\dot{\mathbf{c}}, the time derivative of q˙=Jc˙\dot{\mathbf{q}}=\mathbf{J}\dot{\mathbf{c}}. The disk is then driven by the joint torques τ=(τ1,τ2)\boldsymbol{\tau}=(\tau_1,\tau_2):

M(c)c¨+C(c,c˙)c˙=JTτ+F+f0n0,(8)\mathbf{M}(\mathbf{c})\ddot{\mathbf{c}}+\mathbf{C}(\mathbf{c},\dot{\mathbf{c}})\dot{\mathbf{c}}=\mathbf{J}^{\mathsf{T}}\boldsymbol{\tau}+\mathbf{F}+f_0\mathbf{n}_0, \tag*{(8)}

where M=mI2+IfJTJ\mathbf{M}=m\mathbf{I}_2+I_f\mathbf{J}^{\mathsf{T}}\mathbf{J} is the inertia matrix and C=IfJTJ˙\mathbf{C}=I_f\mathbf{J}^{\mathsf{T}}\dot{\mathbf{J}} is the Coriolis and centripetal matrix. The term IfJTJI_f\mathbf{J}^{\mathsf{T}}\mathbf{J} is the inertia of the fingers as felt by the disk. The term JTτ\mathbf{J}^{\mathsf{T}}\boldsymbol{\tau} is the force of the joint torques on the disk: by power conservation, τTq˙=(JTτ)Tc˙\boldsymbol{\tau}^{\mathsf{T}}\dot{\mathbf{q}}=(\mathbf{J}^{\mathsf{T}}\boldsymbol{\tau})^{\mathsf{T}}\dot{\mathbf{c}}.

The PD controller (1) acts at each joint as a torsional damper of coefficient kdk_d in parallel with a torsional spring of stiffness kpk_p and rest angle qrefq_{\mathrm{ref}}. The potentials of the two springs sum to the controller potential

V(c)=kp2∑iei(c)2.(9)V(\mathbf{c})=\frac{k_p}{2}\sum_i e_i(\mathbf{c})^2. \tag*{(9)}

Since ∇ei=−gi\nabla e_i=-\mathbf{g}_i by (5), the gradient of the controller potential is ∇V=−kp∑ieigi\nabla V=-k_p\sum_i e_i\mathbf{g}_i, and e˙i=−giTc˙\dot e_i=-\mathbf{g}_i^{\mathsf{T}}\dot{\mathbf{c}}. The joint torques therefore act on the disk as

JTτ=∑igiτi=∑igi(kpei+kde˙i)=−∇V−Dc˙,\mathbf{J}^{\mathsf{T}}\boldsymbol{\tau}=\sum_i\mathbf{g}_i\tau_i=\sum_i\mathbf{g}_i(k_pe_i+k_d\dot e_i)=-\nabla V-\mathbf{D}\dot{\mathbf{c}},

with the damping matrix D=kdJTJ\mathbf{D}=k_d\mathbf{J}^{\mathsf{T}}\mathbf{J}. The closed loop is therefore the mechanical system

M(c)c¨+C(c,c˙)c˙+D(c)c˙+∇V(c)=F+f0n0,(10)\mathbf{M}(\mathbf{c})\ddot{\mathbf{c}}+\mathbf{C}(\mathbf{c},\dot{\mathbf{c}})\dot{\mathbf{c}}+\mathbf{D}(\mathbf{c})\dot{\mathbf{c}}+\nabla V(\mathbf{c})=\mathbf{F}+f_0\mathbf{n}_0, \tag*{(10)}

in the standard manipulator form: inertial, Coriolis, damping, and potential forces on the left, and the load and the palm force on the right. The control parameters enter only as constants, and the load F\mathbf{F} is the input. The controller sets the stiffness, through VV, and the damping D\mathbf{D}. Both also depend on the position of the disk, through J\mathbf{J}.

The palm contact is unilateral, so the system has two modes. (i) Off the palm (cx>rc_x>r), f0=0f_0=0, and (10) is a two-degree-of-freedom system in c\mathbf{c}. (ii) On the palm (cx=rc_x=r, c˙x=c¨x=0\dot c_x=\ddot c_x=0), the xx row of (10) gives the palm force f0≥0f_0\geq0, and the yy row gives the lateral dynamics. The disk leaves the palm when this force would become negative. At the palm-release boundary (cx=rc_x=r, f0=0f_0=0), the disk touches the palm without pressing on it.

Input-output characterization of a grasp

Admittance derivation via linearization

We characterize a grasp by its admittance, the transfer matrix from load perturbations to displacements around an equilibrium. A forced equilibrium (cˉ,Fˉ)(\bar{\mathbf{c}},\bar{\mathbf{F}}) is a position cˉ\bar{\mathbf{c}} at which the disk rests under a constant load Fˉ\bar{\mathbf{F}}. There, the force that the controlled fingers apply to the disk balances the load and, on the palm, the palm force. At rest, (10) reduces to

∇V(cˉ)=Fˉ+f0n0,(11)\nabla V(\bar{\mathbf{c}})=\bar{\mathbf{F}}+f_0\mathbf{n}_0, \tag*{(11)}

with f0=0f_0=0 off the palm (cˉx>r\bar c_x>r) and f0≥0f_0\geq0 on the palm (cˉx=r\bar c_x=r). Off the palm, the equilibria under a load Fˉ\bar{\mathbf{F}} are the stationary points of the total potential V(c)−FˉTcV(\mathbf{c})-\bar{\mathbf{F}}^{\mathsf{T}}\mathbf{c}.

Consider δc=c−cˉ\delta\mathbf{c}=\mathbf{c}-\bar{\mathbf{c}} and δF=F−Fˉ\delta\mathbf{F}=\mathbf{F}-\bar{\mathbf{F}}. Since J\mathbf{J} is linear in c\mathbf{c}, the Coriolis term Cc˙\mathbf{C}\dot{\mathbf{c}} is quadratic in c˙\dot{\mathbf{c}} and has no first-order part. Linearizing (10) therefore gives

Mδc¨+Dδc˙+Kδc=δF,K=∇2V,(12)\mathbf{M}\delta\ddot{\mathbf{c}}+\mathbf{D}\delta\dot{\mathbf{c}}+\mathbf{K}\delta\mathbf{c}=\delta\mathbf{F},\qquad\mathbf{K}=\nabla^2V, \tag*{(12)}

where M\mathbf{M}, D\mathbf{D}, and the stiffness matrix K\mathbf{K} are evaluated at cˉ\bar{\mathbf{c}}. In the Laplace domain, δc(s)=H(s)δF(s)\delta\mathbf{c}(s)=\mathbf{H}(s)\delta\mathbf{F}(s), with

H(s)=(Ms2+Ds+K)−1∈C2×2.(13)\mathbf{H}(s)=(\mathbf{M}s^2+\mathbf{D}s+\mathbf{K})^{-1}\in\mathbb{C}^{2\times2}. \tag*{(13)}

The admittance (13) is valid off the palm and at the palm-release boundary (f0=0f_0=0). On the palm (f0>0f_0>0), the palm force absorbs small perturbations of the axial load, and the disk does not move along xx. The lateral admittance 1/(Myys2+Dyys+Kyy)1/(M_{yy}s^2+D_{yy}s+K_{yy}) still captures the lateral motion.

Static metrics: stiffness and stability

At zero frequency, the admittance captures the stiffness of the grasp, which also decides its stability. Off the palm, a constant load perturbation δF\delta\mathbf{F} causes the displacement H(0)δF\mathbf{H}(0)\delta\mathbf{F}, where H(0)=K−1\mathbf{H}(0)=\mathbf{K}^{-1}. The inertia matrix M\mathbf{M} is positive definite, and so is the damping matrix D=kdJTJ\mathbf{D}=k_d\mathbf{J}^{\mathsf{T}}\mathbf{J} when the two finger normals are not parallel. Therefore, off the palm, all poles of H\mathbf{H} have a negative real part if and only if K\mathbf{K} is positive definite [16, 17]. The grasp is unstable if K\mathbf{K} has a negative eigenvalue. Stability is therefore read from the curvature of the potential at the equilibrium. At the boundary of stability, K\mathbf{K} is singular: the grasp has no stiffness in some direction, and a small load moves the disk by a large amount. On the palm, away from the palm-release boundary, the grasp is stable if and only if Kyy>0K_{yy}>0.

Dynamic response and resonances

At nonzero frequency, the admittance captures the response to time-varying load perturbations. The modulus of each of its poles, for example, captures a natural frequency of the grasp, near which load perturbations are amplified. Likewise, the damping ratio of each pole, the absolute value of the ratio of its real part to its modulus, captures the response oscillations.

The maximal amplification that a time-varying load produces is classically captured by the peak gain ∥H∥∞=max⁡ωσˉ(H(jω))\lVert\mathbf{H} \rVert_{\infty} = \max_{\omega} \bar{\sigma}\left(\mathbf{H}(\mathrm{j}\omega)\right), where σˉ\bar{\sigma} is the largest singular value. The maximum can also be restricted to task-relevant frequencies ω∈[0,ωˉ]\omega\in[0,\bar{\omega}]. Compared with the static value, or DC gain, σˉ(H(0))\bar{\sigma}(\mathbf{H}(0)), the peak gain tells how much the stiffness underestimates the displacement under time-varying perturbations.

These considerations can be further specialized to the diagonal terms of H(s)\mathbf{H}(s), which relate a load perturbation to the displacement in the same direction, and to its off-diagonal terms, which capture the displacement in one direction caused by a load perturbation in another direction, such as the lateral displacement caused by an axial load.

Two grasps with the same stiffness matrix can differ in their dynamic response. The admittance captures these differences, and therefore the effects of accelerations and impacts in grasping. It also maps the gripper parameters directly to grasp features: each choice of these parameters gives a specific linearization, hence specific poles and peak gains. This gives a direct link between the gripper parameters on the one hand and the resonances, peak gain, and stability of the grasp on the other. Within the simplified setting of this paper, the admittance reduces to a diagonal matrix, which captures decoupled responses along the xx and yy axes.

Static analysis of symmetric grasps

For symmetric grasps, the equilibria and their stability are a function of the holding force and depend on two key quantities. A grasp is symmetric when the load acts along the symmetry axis, F=(Fx,0)\mathbf{F} = (F_x,0) with Fx≥0F_x \ge0, and the disk is centered, cy=0c_y = 0. Both fingers then have the same angle qq, error e=qref−qe = q_{\mathrm{ref}} - q, and contact distance ℓ\ell. For such grasps, the axial and lateral motions are decoupled: the matrices of Section III-A are diagonal, M=diag⁡(Mxx,Myy)\mathbf{M} = \operatorname{diag}(M_{xx},M_{yy}), D=diag⁡(Dxx,Dyy)\mathbf{D} = \operatorname{diag}(D_{xx},D_{yy}), and K=diag⁡(Kxx,Kyy)\mathbf{K} = \operatorname{diag}(K_{xx},K_{yy}).

Stability and bifurcation analysis

Lateral stability: The lateral stiffness is positive in every symmetric grasp. Since ∂ei/∂cy=−gi,y\partial e_i/\partial c_y = -g_{i,y}, it reads

Kyy=kp∑i(gi,y2−e∂gi,y∂cy).(14)K_{yy} = k_p \sum_i \left(g_{i,y}^2 - e \frac{\partial g_{i,y}}{\partial c_y}\right). \tag*{(14)}

The first term is positive. For the second term, gi,y=−νicos⁡qi/ℓig_{i,y} = -\nu_i \cos q_i/\ell_i. When the disk moves toward finger ii, that is, in the direction νi\nu_i, this finger opens and its contact point moves toward the joint, so cos⁡qi/ℓi\cos q_i/\ell_i grows. Hence, ∂gi,y/∂cy<0\partial g_{i,y}/\partial c_y < 0 for both fingers. Finally, e≥0e \ge0 at rest, because kpe=ℓfik_p e = \ell f_i and the fingers can only push. Hence, Kyy>0K_{yy} > 0. On the palm, a symmetric grasp is therefore always stable. Off the palm, its stability depends on the axial stiffness KxxK_{xx}.

Holding force and equilibria: Along the axis, the equilibria are the positions where the holding force, the force with which the fingers push the disk toward the palm, balances the load. By (4), qq and ℓ\ell depend only on cxc_x, so the holding force is a function of cxc_x only. The disk moves from the palm, cx=rc_x = r, to the fingertip, cx=cx,tipc_x = c_{x,\mathrm{tip}}, where ℓ(cx,tip)=L\ell(c_{x,\mathrm{tip}}) = L.

Recall that ℓ>r\ell> r, so q(cx)>0q(c_x) > 0.

Since cy=0c_y = 0, the yy-components of g1\mathbf{g}_1 and g2\mathbf{g}_2 cancel out. The fingers push the disk toward the palm with the force −∇V=−P(cx)n0-\nabla V = -P(c_x)\mathbf{n}_0, where

P(cx)=2kpe(cx) σ(cx),σ(cx)=−q′(cx)=sin⁡q(cx)ℓ(cx),(15)P(c_x) = 2k_p e(c_x)\,\sigma(c_x), \qquad\sigma(c_x) = -q'(c_x) = \frac{\sin q(c_x)}{\ell(c_x)}, \tag*{(15)}

where e(cx)=qref−q(cx)e(c_x) = q_{\mathrm{ref}} - q(c_x) is the error and the prime denotes the derivative with respect to cxc_x. The transmission σ\sigma tells how fast the fingers open when the disk moves away from the palm: a displacement δcx\delta c_x opens each finger by σ δcx\sigma\,\delta c_x. Its expression follows from gi=∇qi\mathbf{g}_i = \nabla q_i in (5). By virtual work, the joint torque kpek_p e of each finger therefore pushes the disk toward the palm with the force kpeσk_p e \sigma, and the two fingers together give PP. The holding force is positive wherever the fingers press on the disk (e>0e > 0).

The torque and the transmission vary in opposite directions. When the disk moves away from the palm, the fingers open, so ee and the torque grow. Meanwhile, the contact distance ℓ(cx)\ell(c_x) increases and the fingers become more aligned with xx, which together reduce σ\sigma.

The xx row of the equilibrium condition (11) reduces to f0=P(cx)−Fxf_0 = P(c_x) - F_x, and its yy row holds by symmetry. The disk therefore rests on the palm, cx=rc_x = r, if and only if P(r)≥FxP(r) \ge F_x, with the palm force f0=P(r)−Fxf_0 = P(r) - F_x. Off the palm, the disk is at equilibrium at every cx∈(r,cx,tip]c_x \in(r,c_{x,\mathrm{tip}}] such that P(cx)=FxP(c_x) = F_x. Graphically, these equilibria are the intersections of the curve P(cx)P(c_x) with the horizontal line FxF_x. Their number and positions depend on the gripper parameters, in particular on the reference qrefq_{\mathrm{ref}}: depending on qrefq_{\mathrm{ref}}, P(cx)P(c_x) either rises then falls or decreases from the palm (Fig. 3.

Axial stability: Off the palm, an equilibrium is stable if and only if the holding force increases with the position cxc_x of the disk. Stability depends on the sign of the axial stiffness KxxK_{xx}. Since cy=0c_y = 0, P=∂V/∂cxP = \partial V/\partial c_x, so Kxx=K_{xx} = P′(cx)P'(c_x). The reference is constant, so the error grows as the fingers open: e′=−q′=σe'=-q'=\sigma. Differentiating (15) then gives

Kxx=2kp(σ2+eσ′)=2kpsin⁡qℓ2[sin⁡q−e(cos⁡q+cxℓ)].(16)\begin{aligned} K_{xx} &= 2k_{\mathrm p}\left(\sigma^2+e\sigma'\right) \\ &= \frac{2k_{\mathrm p}\sin q}{\ell^2}\left[\sin q-e\left(\cos q+\frac{c_x}{\ell}\right)\right]. \tag*{(16)} \end{aligned}

In the last expression, we have used q′=−sin⁡q/ℓq'=-\sin q/\ell and ℓ′=cx/ℓ\ell'=c_x/\ell. The first expression, 2kp(σ2+eσ′)2k_{\mathrm p}\left(\sigma^2+e\sigma'\right), combines the transmission σ\sigma with the transmission variation σ′\sigma', weighted by the error ee. Their competition decides the sign of P′(cx)P'(c_x): stable equilibria lie on the rising parts of P(cx)P(c_x), unstable ones on the falling parts (Figure 3). This split recovers the known decomposition of the grasp stiffness into the gain seen through the Jacobian and a geometric term proportional to the joint torques [3, 18]. For this gripper, the geometric term is always negative, because the transmission decreases as the disk moves away from the palm.

Reference holding-force curves for symmetric grasps

Figure 3. The reference sets the shape of the holding force P(cx)P(c_x): with qref=20∘q_{\mathrm{ref}} = 20^\circ (left), PP rises then falls; with qref=90∘q_{\mathrm{ref}} = 90^\circ (right), it decreases from the palm. Both use the same gain kpk_p, but the holding force on the right is much larger. The equilibria lie where the horizontal line FxF_x meets the curve: stable (filled dots, solid) and unstable (empty dots, dashed) off the palm, and on the palm (square) while Fx≤P(r)F_x \le P(r).

The factor 2kpsin⁡qℓ2\frac{2k_{\mathrm p}\sin q}{\ell^2} in (16) is positive, so the sign of KxxK_{xx} is that of the term in square brackets. An equilibrium off the palm at cxc_x is therefore stable if

e<e∗(cx)=sin⁡q(cx)cos⁡q(cx)+cx/ℓ(cx),(17)e<e^*(c_x)=\frac{\sin q(c_x)}{\cos q(c_x)+c_x/\ell(c_x)}, \tag*{(17)}

and unstable if e>e∗(cx)e>e^*(c_x). Equivalently, e∗=σ2/∣σ′∣e^*=\sigma^2/\lvert\sigma'\rvert: it is the critical error at which the relative growth of the joint torque, σ/e\sigma/e, equals the relative loss of transmission, ∣σ′∣/σ\lvert\sigma'\rvert/\sigma.

Bifurcation plane: For a given gripper, the equilibria and their stability depend on two key quantities: the reference qrefq_{\mathrm{ref}} and the normalized gain κ=2kp/(dFx)\kappa=2k_{\mathrm p}/(dF_x). In fact, the holding force (15) is proportional to kpk_{\mathrm p}, so the equilibrium condition P(cx)=FxP(c_x)=F_x reads

κde(cx)σ(cx)=1,(18)\kappa d e(c_x)\sigma(c_x)=1, \tag*{(18)}

where κ\kappa and deσd e\sigma are dimensionless, with ee in radians. The reference qrefq_{\mathrm{ref}} sets the shape of the holding force, and the normalized gain κ\kappa sets its scale. Doubling both the load and the gain leaves every equilibrium unchanged. The plane (qref,κ)(q_{\mathrm{ref}},\kappa) therefore summarizes the equilibria and their stability (Figure 4): moving up in this plane means decreasing the load at a given gain or, equivalently, increasing the gain under a given load.

Figure 4. The reference qrefq_{\mathrm{ref}} and the normalized gain κ\kappa set the number, location (on or off the palm), and stability (S: stable, U: unstable) of the axial equilibria, for all loads and gains. Three curves separate the regions: palm-release (solid), fingertip (dotted), and fold (dashed).

The plane is divided into regions according to the number, location, and stability of the equilibria. At a fixed gain, moving up a vertical line in Figure 4 is equivalent to lowering the horizontal line FxF_x in Figure 3, whose intersections with the curve P(cx)P(c_x) determine the equilibria and their stability.

Three curves separate the regions of Figure 4. On the palm-release curve (solid), Fx=P(r)F_x=P(r): the palm force vanishes and the disk leaves the palm. On the fingertip curve (dotted), Fx=P(cx,tip)F_x=P(c_{x,\mathrm{tip}}): an off-palm equilibrium reaches the fingertip. On the fold curve (dashed), FxF_x equals the maximum of PP: the stable and unstable off-palm equilibria merge and disappear in a saddle-node bifurcation. Beyond this curve, the load exceeds the largest holding force, and the grasp is lost. The difference max⁡cxP(cx)−Fx\max_{c_x}P(c_x)-F_x is the axial static margin, the largest additional constant load along xx for which an equilibrium remains: in Figure 3, the height of the top of the curve PP above the line FxF_x. Unlike the admittance, which is local, the static margin is global.

These curves delimit four regions with different equilibria. The dark regions have a single stable equilibrium, on the palm (blue) or off the palm (orange), separated by the palm-release curve. Crossing the fingertip curve toward the light regions adds an unstable equilibrium. It is the empty dot of Figure 3, and it bounds the basin of attraction of the stable equilibrium: a disk displacement beyond this point cannot be recovered. Elsewhere, no equilibrium exists and the grasp is lost. The fold and palm-release curves meet at (q∗,κ∗)(q^*,\kappa^*). Stable equilibria off the palm require qref<q∗q_{\mathrm{ref}}<q^* and κ>κ∗\kappa>\kappa^*.

Effect of the load and the gripper parameters

Increasing the load: For a fixed controller (kp,qref)(k_{\mathrm p},q_{\mathrm{ref}}), slowly increasing the load FxF_x is equivalent to moving down along a vertical line in Figure 4. We observe three qualitative behaviors. For large references (qref>q∗)(q_{\mathrm{ref}}>q^*), the vertical line crosses only blue regions: the disk stays on the palm until the load reaches the holding force at the palm, then leaves the palm, and the grasp is lost at once. For intermediate references, the vertical line crosses blue then orange regions: the disk rests on the palm, then is released from it and held by the fingers until, for an even larger load, the grasp is lost. For small references, the vertical line crosses only orange regions: the disk never rests on the palm. Overall, the reference qrefq_{\mathrm{ref}} sets the qualitative behavior, while the gain kpk_{\mathrm p} scales the loads at which transitions occur. Large references and large gains therefore give a firmer grasp: they increase the static margin, so that an equilibrium remains under larger loads. This separation of roles can inform the choice of the control parameters for a given object.

Same equilibrium, different stiffness: Under a given load, different controllers (kp,qref)(k_{\mathrm p},q_{\mathrm{ref}}) can hold the disk at the same equilibrium, that is, at the same position and with the same contact forces. At a given position cxc_x, the force kpe/ℓk_{\mathrm p}e/\ell of each finger is unchanged if kpk_{\mathrm p} increases while the static error e=qref−qe=q_{\mathrm{ref}}-q decreases in proportion. Each equilibrium thus corresponds to a family of controllers, represented by the black curves of Figure 5.

Bifurcation curves for constant position and holding force

Figure 5. Along each black curve, the controllers (kp,qref)(k_p,q_{\mathrm{ref}}) hold the disk at the same equilibrium. Moving up a curve raises kpk_p, lowers qrefq_{\mathrm{ref}} toward the finger angle, and raises the stiffness. Left: curves of constant position, along which the disk rests off the palm at cx=35c_x=35, 50 and 70 mm. The equilibrium is stable on the solid part and becomes unstable on the dashed part, the two parts meeting on the fold. Right: curves of constant holding force, P(r)=2FxP(r)=2F_x, 5Fx5F_x, and 20Fx20F_x.

The stiffness nevertheless changes: in KxxK_{xx} (16) and KyyK_{yy} (14), the term proportional to kpek_p e is constant along the curves of Figure 5, while the term proportional to kpk_p is not. As kpk_p decreases, KxxK_{xx} can even become negative, making the equilibrium unstable (dashed lines). From a design perspective, the equilibrium provides only partial information about the grasp. The controller (kp,qref)(k_p,q_{\mathrm{ref}}) can be tuned to adjust the stiffness without disturbing the target equilibrium.

Changing the gripper morphology: The ratio r/dr/d of the disk radius to the half-distance between the finger joints affects the bifurcation plane, as shown in Figure 6. For a large disk, with r/dr/d close to 1, the fingers are nearly parallel to the xx direction and therefore transmit little of their torque along xx. For example, from r/d=0.5r/d=0.5 to 0.90.9, the critical q∗q^* drops from 63∘63^\circ to 9∘9^\circ, and κ∗\kappa^* rises from 3.6 to 172. Holding a large disk off the palm therefore requires a small static error ee and large normalized gains. In practice, only the equilibria on the palm can handle constant load perturbations.

Figure 6. A larger disk moves the stable equilibria off the palm toward small references and large normalized gains. Bifurcation planes for r/d=0.5r/d=0.5, 0.750.75, and 0.90.9; the regions are those of Figure 4, and the dots mark (q∗,κ∗)(q^*,\kappa^*).

Dynamic responses of symmetric grasps

In what follows, we show how grasps that are equivalent under static metrics can exhibit different responses to time-varying load perturbations. We also show that the finger inertia is irrelevant from a static perspective but has a clear impact on the dynamic response. For illustration purposes, the derivative gain kdk_d is kept at its nominal value (Table I). We support our discussion by varying the proportional gain kpk_p and the reference qrefq_{\mathrm{ref}}. Proper controller tuning, in which kpk_p and kdk_d are usually chosen together, is outside the scope of this paper.

Recall that the diagonal matrices of Section IV split the admittance into an axial and a lateral channel, Hxx(s)=1/(Mxxs2+Dxxs+Kxx)H_{xx}(s)=1/(M_{xx}s^2+D_{xx}s+K_{xx}) and Hyy(s)=1/(Myys2+Dyys+Kyy)H_{yy}(s)=1/(M_{yy}s^2+D_{yy}s+K_{yy}), each a mass-spring-damper system. Their stiffnesses are given by (16) and (14), while their inertias and dampings are

Mxx=m+2Ifσ2,Dxx=2kdσ2,M_{xx}=m+2I_f\sigma^2,\qquad D_{xx}=2k_d\sigma^2,
Myy=m+2Ifcos⁡2qℓ2,Dyy=2kdcos⁡2qℓ2.(19)M_{yy}=m+2I_f\frac{\cos^2 q}{\ell^2},\qquad D_{yy}=2k_d\frac{\cos^2 q}{\ell^2}. \tag*{(19)}

As they transmit their torque in the holding force (15), the fingers transmit their inertia and their damping to the disk along xx through the transmission σ\sigma.

Same forced equilibrium, different dynamic responses

Grasps that share the same forced equilibrium and have the same inertia and damping can differ in their stiffness, which alone changes their dynamic response. Along the thick black curve in Figure 7 (left), the position of the disk and the contact forces are fixed. The transmission σ\sigma is then fixed, and so are MxxM_{xx} and DxxD_{xx}, by (19). Because the equilibrium is fixed, the torque kpek_p e is also constant. Thus, the stiffness KxxK_{xx} in (16) depends only on kpk_p and increases linearly with it.

Grasps at the same forced equilibrium and their axial and lateral admittances

Figure 7. Grasps at the same forced equilibrium differ in their dynamic response: a higher kpk_p with a lower qrefq_{\mathrm{ref}} raises the stiffness and the natural frequency and sharpens the peak. Left: three grasps on the curve cx=35c_x = 35 mm of Figure 5 (left), at (qref,κ)=(19.5∘,50)(q_{\mathrm{ref}}, \kappa) = (19.5^\circ, 50) (blue), (17.0∘,100)(17.0^\circ, 100) (rose), and (14.7∘,1000)(14.7^\circ, 1000) (gray). Right: axial (top) and lateral (bottom) admittances of these grasps. Dashed vertical lines mark the natural frequency ωn\omega_n, and shaded bars the ratio sup⁡ω∣Hxx(jω)∣/Hxx(0)\sup_\omega|H_{xx}(j\omega)|/H_{xx}(0).

Moving up along the curve, toward higher gains kpk_p and smaller references qrefq_{\mathrm{ref}}, changes the dynamic response in three ways. First, the DC gain Hxx(0)=1/KxxH_{xx}(0)=1/K_{xx} decreases, so a constant load perturbation moves the disk less. Second, the damping ratio decreases, so the ratio of the peak gain to the DC gain, sup⁡ω∣Hxx(jω)∣/Hxx(0)\sup_\omega|H_{xx}(j\omega)|/H_{xx}(0), increases, as shown in Figure 7 (right). For low proportional gains, the grasp thus responds almost uniformly over frequency and oscillates little in response to a step load perturbation. In contrast, for high proportional gains, the grasp has a clear resonance and oscillates longer in response to the same perturbation. Finally, the natural frequency of the grasp increases as the proportional gain increases. Therefore, only faster load perturbations are amplified. However, an extremely high proportional gain does not necessarily make the grasp better, due to practical limitations and noise sensitivity. The lateral channel follows a similar trend.

Same stiffness, different dynamic responses

Grasps with the same stiffness can still differ dynamically, because the damping transmitted by the fingers depends on the position of the disk. The thick curve in Figure 8 (left) represents grasps with the same stiffness KxxK_{xx}. Unlike in the previous section, the disk rests at different positions cxc_x.

Figure 8. Grasps with the same stiffness differ in their peak gain, which grows as the disk moves away from the palm. Left: curves of constant stiffness Kxx=20K_{xx} = 20, 8080 and 320320 N m−1^{-1}, for the load Fx=0.6F_x = 0.6 N. Grasps A, B, and C lie on the 2020 N m−1^{-1} curve, at cx=60c_x = 60 mm (A, green), 4040 mm (B, orange), and 3232 mm (C, black). Right: their axial admittance ∣Hxx∣|H_{xx}|, with a linear zoom near ωn\omega_n; the DC gain Hxx(0)H_{xx}(0) is the same.

For the nominal parameters of Table I, the fingers add a small term 2Ifσ22I_f\sigma^2 to the disk mass mm in the inertia MxxM_{xx} of (19). Both MxxM_{xx} and the natural frequency therefore barely change along the curve. The damping Dxx=2kdσ2D_{xx}=2k_d\sigma^2, however, decreases as the disk moves away from the palm, because the transmission σ\sigma decreases (Section IV-A). The damping ratio therefore decreases, and the peak gain sup⁡ω∣Hxx(jω)∣\sup_\omega|H_{xx}(j\omega)| increases, as shown in Figure 8 (right). Damping in the object, from its interaction with the environment, or friction at the contacts would reduce this effect, but not remove it. These grasps also differ in their lateral stiffness (not shown).

A target axial stiffness therefore does not fully determine the dynamic response. Within the family of controllers that share the same stiffness, those that hold the disk closer to the palm, with a small proportional gain kpk_p and a high reference qrefq_{\mathrm{ref}}, achieve higher damping. Thus, they oscillate less in response to a step load perturbation and have a lower peak gain.

The role of finger inertia

The finger inertia affects neither the equilibrium nor the stiffness of a grasp, but it changes its dynamic response. Static metrics are independent of finger inertia and therefore miss this effect. By (19), the finger inertia IfI_f enters only MxxM_{xx} and MyyM_{yy}. A larger finger inertia therefore lowers the natural frequency and the damping ratio of each channel and raises its peak gain.

The two channels are not affected equally. By (19), the finger inertia adds 2Ifsin⁡2q/ℓ22I_f\sin^2q/\ell^2 to MxxM_{xx} and 2Ifcos⁡2q/ℓ22I_f\cos^2q/\ell^2 to MyyM_{yy}, in the ratio cot⁡2q\cot^2q. It therefore affects the lateral channel more when the fingers are closer to the xx direction

(q<45∘q < 45^\circ), and the axial channel more otherwise. Which case occurs depends only on the geometry: qq is largest at the palm, where it exceeds 45∘45^\circ only for a small disk, with r/d<0.41r/d < 0.41. With the nominal geometry, all grasps are in the first case. For grasp B, a larger finger inertia lowers the lateral damping ratio enough for a resonance peak to appear, whereas the axial response barely changes (Figure 9).

Figure 9. A larger finger inertia lowers the natural frequency, mostly in the lateral channel, where a peak appears. Axial (top) and lateral (bottom) admittances of grasp B of Figure 8, for the nominal finger inertia If=6.7×10−5I_f = 6.7 \times10^{-5} kg m2^2 and an inertia 10 times larger. The stiffness is the same.

The controller only partly compensates for the finger inertia. A higher kdk_d restores the damping ratio, hence lowers the peak gain, but not the natural frequency. A higher kpk_p restores the natural frequency only by raising the stiffness, which changes the response to constant loads and further lowers the damping ratio. Lighter fingers avoid this trade-off.

Nonlinear responses

In this section, we show that the small-signal admittance captures relevant features of the full nonlinear behavior. We simulated the full dynamics ((10)) for grasps A, B, and C of Figure 8, under sinusoidal axial load perturbations of fixed frequency. The amplitude of the load perturbation is slowly increased, which moves the grasp progressively from the small-signal regime to the nonlinear regime. For each frequency, we recorded the smallest amplitude that made the grasp fail (Figure 10, top). A grasp fails when the disk is ejected or when it hits the palm. The impact with the palm is a second failure mode, which the admittance does not describe, since it assumes that the disk moves freely between the fingers. Because an impact already counts as a failure, each simulation stops at the first impact. The amplitude is normalized by the static margin of Section IV-A.

Nonlinear simulations of grasps A, B, and C

Figure 10. Nonlinear simulations of grasps A, B, and C of Figure 8. The failure amplitude of the nonlinear model is correlated with the axial admittance. Top: smallest amplitude of a sinusoidal axial load perturbation that ejects the disk (solid) or makes it land on the palm (dotted), normalized by the static margin (horizontal line). The vertical line marks the natural frequency ωn\omega_n of the linearized model, shared by the three grasps. Bottom: response to an axial step of 0.85 times the static margin: A is ejected, B and C settle.

The failure curves are well correlated with the axial admittance. Below ωn\omega_n, the grasps fail at the static margin, as under a constant load. However, near ωn\omega_n, grasp A fails at an amplitude that is about 0.450.45 times the static margin. This is expected, given the high peak gain of A in Figure 8. In contrast, grasp B fails close to the static margin up to ωn\omega_n. For both, above ωn\omega_n, the inertia filters the load perturbation, and the failure amplitude grows with frequency. Grasp C, closer to the palm, lands on it before being ejected (dotted). The palm then blocks the axial motion and the dynamics change abruptly. This scenario lies outside the domain of validity of the linearized model.

The small-signal analysis, however, does not predict the large variations of the curve of A compared with B (Figure 10, top). As the disk moves along the fingers, the stiffness of the grasp changes. This nonlinearity distorts the response and spreads the effect of the resonance over a wider range of frequencies.

The admittance also predicts the axial step response well (Figure 10, bottom). A step of 0.85 times the static margin of each grasp ejects A, whereas B and C settle, with larger oscillations for B than for C. A step excites all frequencies, so its overshoot grows with the peak gain, which is highest for A and lowest for C (Figure 8). The overshoot of A carries the disk out of the fingers, although the step stays 15 % below its static margin.

Conclusion

Using a minimal gripper, we showed that neither the equilibrium nor the stiffness of a grasp fully determines its response to load perturbations. The admittance captures this response, demonstrating quantitatively that statically equivalent grasps can exhibit distinct behaviors when interacting with time-varying external perturbations. These grasps differ through the gain and the reference, the position of the disk, and the finger inertia. Nonlinear simulations confirmed the main features predicted by the admittance.

Our simplified gripper allows analytical derivations, but the admittance can also be obtained for general grippers, either numerically or experimentally. This matters for real grippers, which have nonlinear damping and static friction, and whose rotor inertia, multiplied by the square of the gear ratio, can dominate the finger inertia [6]. Furthermore, real objects are rarely symmetric, and measurement noise, the sampling of a digital controller, and actuator saturation limit the gains that can be used.

We will study these effects in future work. This study was motivated by our ongoing research on anthropomorphic robotic hands [19], where our control approach extends the PD control studied here to a network of virtual springs and dampers. Our next step is to compute the admittance of such a hand by automatic differentiation of its analytical model, and to validate it experimentally.

Acknowledgments

The authors used Claude (Anthropic) to help implement the code of Sections IV and V and the TikZ code of the figures. The authors reviewed and edited the content as needed and take full responsibility for the publication.

References

  1. [1]M. T. Mason, “Compliance and force control for computer controlled manipulators,” IEEE Trans. Syst., Man, Cybern., vol. 11, no. 6, pp. 418–432, 1981.DOI
  2. [2]N. Hogan, “Impedance control: An approach to manipulation: Part I—Theory,” ASME J. Dyn. Sys., Meas., Control, vol. 107, no. 1, pp. 1–7, 1985.DOI
  3. [3]M. R. Cutkosky and I. Kao, “Computing and controlling compliance of a robotic hand,” IEEE Trans. Robot. Autom., vol. 5, no. 2, pp. 151–165, 1989.DOI
  4. [4]P. M. Wensing, A. Wang, S. Seok, D. Otten, J. Lang, and S. Kim, “Proprioceptive actuator design in the MIT Cheetah: Impact mitigation and high-bandwidth physical interaction for dynamic legged robots,” IEEE Trans. Robot., vol. 33, no. 3, pp. 509–522, 2017.DOI
  5. [5]J. Lee, A. Choi, and S. Jeong, “Ultra-low-impedance robotic gripper for high-bandwidth and transparent physical interaction,” arXiv:2608.09198, 2026.arxiv.org/abs/2608.09198
  6. [6]A. Bhatia, A. M. Johnson, and M. T. Mason, “Direct drive hands: Force-motion transparency in gripper design,” in Proc. Robot.: Sci. Syst., Freiburg im Breisgau, Germany, 2019.
  7. [7]M. G. Catalano, G. Grioli, E. Farnioli, A. Serio, C. Piazza, and A. Bicchi, “Adaptive synergies for the design and control of the Pisa/IIT SoftHand,” Int. J. Robot. Res., vol. 33, no. 5, pp. 768–782, 2014.DOI
  8. [8]W. Friedl and M. A. Roa, “CLASH—A compliant sensorized hand for handling delicate objects,” Front. Robot. AI, vol. 6, 2020.DOI
  9. [9]M. A. Roa and R. Suárez, “Grasp quality measures: Review and performance,” Auton. Robots, vol. 38, no. 1, pp. 65–88, 2015.pubmed.ncbi.nlm.nih.gov/26074671
  10. [10]T. Wimböck, C. Ott, A. Albu-Schäffer, and G. Hirzinger, “Comparison of object-level grasp controllers for dynamic dexterous manipulation,” Int. J. Robot. Res., vol. 31, no. 1, pp. 3–23, 2012.DOI
  11. [11]C. Ferrari and J. Canny, “Planning optimal grasps,” in Proc. IEEE Int. Conf. Robot. Autom., vol. 3, Nice, France, 1992, pp. 2290–2295.
  12. [12]Q. Lin, J. W. Burdick, and E. Rimon, “A stiffness-based quality measure for compliant grasps and fixtures,” IEEE Trans. Robot. Autom., vol. 16, no. 6, pp. 675–688, 2000.DOI
  13. [13]Y. Yokokohji, J. San Martin, and M. Fujiwara, “Dynamic manipulability of multifingered grasping,” IEEE Trans. Robot., vol. 25, no. 4, pp. 947–954, 2009.DOI
  14. [14]J. Kim, K. Iwamoto, J. J. Kuffner, Y. Ota, and N. S. Pollard, “Physically based grasp quality evaluation under pose uncertainty,” IEEE Trans. Robot., vol. 29, no. 6, pp. 1424–1439, 2013.DOI
  15. [15]D. Prattichizzo and A. Bicchi, “Dynamic analysis of mobility and graspability of general manipulation systems,” IEEE Trans. Robot. Autom., vol. 14, no. 2, pp. 241–258, 1998.DOI
  16. [16]W. Thomson and P. G. Tait, Treatise on Natural Philosophy, 2nd ed. Cambridge, U.K.: Cambridge Univ. Press, 1879, vol. 1.
  17. [17]W. S. Howard and V. Kumar, “On the stability of grasped objects,” IEEE Trans. Robot. Autom., vol. 12, no. 6, pp. 904–917, 1996.DOI
  18. [18]S.-F. Chen and I. Kao, “Conservative congruence transformation for joint and Cartesian stiffness matrices of robotic hands and fingers,” Int. J. Robot. Res., vol. 19, no. 9, pp. 835–847, 2000.DOI
  19. [19]J. Vanderheyden, G. Drion, F. Forni, and P. Sacré, “Grasping by interconnection: Robust closing motions from coarse object templates,” arXiv:2609.19228, 2026, submitted to ICRA 2027.arxiv.org/abs/2609.19228

Paper details

vlnc:W_gnbjkfn3
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Computer Science

Claude (Anthropic)

View statement
Looking for related papers…
Contents