betaFeedback

WorksPhysics and Astronomy

Instability behavior of odd viscosity-induced viscous fluid over a vibrating bed

Abstract

The manuscript focuses on the theoretical stability analysis of the viscous liquid over a vibrating inclined rigid bed when the fluid undergoes an impact of odd viscosity. Such an impact emerges in the classical fluid owing to the broken time-reversal symmetry. The rigid bottom vibrates in streamwise and cross-stream directions. The time-dependent Orr-Sommerfeld eigenvalue problem is obtained using the normal mode approach and resolved based on the Chebyshev-collocation method and the Floquet theory. The effect of the odd viscosity coefficient on the different types of instability gravitational, subharmonic, and harmonic are identified. The gravitational instability arises in the longwave region, whereas the resonated wave instability appears in the finite wavenumber region. The gravitational instability is generated in the fluid flow owing to the gravity driving force, whereas the subharmonic instability appears for lower forcing amplitude and the harmonic instability emerges for comparatively higher forcing amplitude. It is found that the subharmonic and harmonic resonances appear when the forcing amplitude surpasses its critical value. A higher odd viscosity leads to stabilizing the gravitational instability, whereas a larger odd viscosity diminishes the subharmonic resonance along with the harmonic resonance instigated at a high forcing amplitude. Further, a new instability, named shear instability in the finite wavenumber range emerges together with the aforementioned three instabilities when the Reynolds number is sufficiently high with a low angle of inclination and becomes weaker when the time-reversal symmetry breaks.

A Preprint

Introduction

The hydrodynamic instability of fluid flow over a vibrating plane is of great importance in various applications within atomization technology, such as the formation of fuel sprays, high-tech surface cleaning, and advanced material processing [1]. In most circumstances, the bottom vibration is built purposefully, while in other applications, the bottom vibration simply cannot be ignored. Thus, in either situation, it is of interest to us to investigate how the alterations from the ideal condition of a static plane affect the liquid film flow with various physical effects. The bottom vibration can parametrically induce the generation of so-called Faraday waves. It also has the potential to induce Stokes-Rayleigh waves in the viscous liquid layer. It was Yih [2], who initiated an investigation on Newtonian liquid flow over a bounding wall that oscillates horizontally. He used the standard perturbation technique within the framework of Floquet theory to solve the time-dependent Orr–Sommerfeld (OS) boundary value problem (BVP) and examined the behavior of longwave modes under the influence of unsteady base flow. He observed instability of the longwave mode when the amplitude of oscillation reaches a sufficiently large level. Following the work of Yih [2], an extensive examination of the literature ([3], [4], [5], [6], [7], [8], [9], and the citations therein) explored film flow over vibrating inclined/vertical/horizontal substrates, encompassing diverse effects. Or [5] extended the idea of Yih [2] by investigating the finite wavelength instability for infinitesimal perturbations with an arbitrary wavenumber. His findings indicated that the unstable zone in the longwave region emerges in the isolated bandwidth of the applied frequency, whereas the instability in the finite wavenumber arises through the branch points of the longwave marginal curves. Also, he identified relatively stronger instability in finite wavenumber mode than in longwave mode in certain ranges of the imposed frequency. Later, Gao and Lu [8] used a strategy to control instability by adding an insoluble surfactant to the surface of the liquid in the same flow model considered by Yih [2]. They observed the stabilizing impact of insoluble surfactant on the longwave mode. Instead of considering only the streamwise-directed oscillation of a plane, Woods and Lin [1], Lin et al. [4], and Burya and Shkadov [7] examined the instability of a Newtonian fluid flowing over an inclined plane with oscillatory motion perpendicular to its own plane, and the resulting acceleration has two components in the streamwise and cross-streamwise flow directions. Consequently, the effective modulation of gravity causes Faraday waves on the liquid surface, where both subharmonic and synchronous solutions occur.

Dandapat and Gupta [3] extended the unsteady Newtonian flow model of Yih [2] by choosing an unsteady non-Newtonian viscoelastic flow model. The purpose of their extension was to investigate the linear stability analysis in the longwave zone. Later, Samanta [10] revisited the work of Dandapat and Gupta [3] and performed a detailed discussion on the linear stability for the disturbances of an arbitrary wavenumber. He observed that the finite wavenumber instability is higher in comparison to the longwave instability for some ranges of imposed frequency. Recently, the work proposed by Woods and Lin [1] was further extended by Samanta [11] for arbitrary wave numbers by applying shear force at the surface of the liquid layer based on the idea of Smeth and Davis [12] and Smith [13]. The inclined substrate beneath the shear-imposed liquid layer was considered to oscillate in streamwise and cross-stream directions. His numerical findings revealed the presence of three distinct instabilities, namely, gravitational, subharmonic, and harmonic instabilities. For small Reynolds numbers, the subharmonic resonance instigated by a low forcing amplitude becomes stronger, but it can be weakened using a high forcing amplitude while imposed shear is present. However, the externally applied shear can enhance the harmonic resonance that is triggered solely at high forcing amplitude. His motivation behind an imposing external shear at the free surface arose owing to its huge application in many industrial and natural set-ups. For instance, inside an aero-engine bearing chamber, the shearing airflow generated by high-speed rotating parts inside the chamber plays a crucial role in extracting heat from the surface of the oil film [14].

It should be noted that all the above-mentioned articles considered the even viscosity of the viscous stress tensor and avoided the odd viscosity term. However, an odd viscosity term plays a crucial role in the dynamics and instability mechanisms of the flow system. Avron [15] identified that when the time-reversal symmetry of a viscous fluid is spontaneously disrupted or influenced by external fields, the fluid exhibits a second viscosity coefficient referred to as odd viscosity or Hall viscosity. This coefficient, in addition to the conventional viscosity coefficient, introduces an off-diagonal contribution to the Cauchy stress tensor. Hence, it is crucial to use modified Navier-Stokes equations to accurately depict how the presence of the odd viscosity coefficient affects fluid flow dynamics. This coefficient is anticipated to have a significant impact on the complex wave dynamics exhibited by such fluids. Because of this, Lapa and Hughes [16] pioneered a theoretical analysis of swimming strategy in two-dimensional fluids with an odd viscosity coefficient at a low Reynolds number. Later, the impact of the odd viscosity coefficient on the thermocapillary instability of a viscous film over a uniformly heated plane was explored by Kirkinis and Andrejev [17]. They noticed the mitigation of thermocapillary instability when the odd viscosity is introduced in the liquid film. Bao and Jian [18] investigated the influence of odd viscosity on the instability of a falling liquid film in the presence of an external electric field at the liquid surface. Their analytical results acquired by the longwave expansion method revealed that the odd viscosity stabilizes the flow, while the electric field destabilizes the flow. Recently, a comprehensive study into the linear and nonlinear stability of falling liquid film was conducted by Samanta [19] when the time-reversal symmetry was disrupted. He solved the corresponding OS BVP using the numerical technique Chebyshev spectral collocation and affirmed the stabilizing behavior of odd viscosity on the surface and shear waves of the flow. Further, a coupled system of two-equation models in terms of film thickness and flow rate was derived, and the corresponding nonlinear traveling wave solution affirmed that the presence of odd viscosity delays the transition from the base flow to the secondary flow arising from the interaction between nonlinear waves. In recent times, the exploration of the influence of odd viscosity on diverse fluid flow setups has been a focal point for several investigators [20, 21, 22]. Their collective efforts advance our understanding of the complex role that odd viscosity plays in various fluid-dynamic scenarios.

Thus, in the current manuscript, our main objective is to extend the earlier work of Woods and Lin [1] by detecting the influence of odd viscosity on the instability mechanisms of Faraday waves emerging on the surface of viscous fluid over a vibrating inclined plane for arbitrary wavenumbers. So far, no analyses have enlightened the finite wavenumber linear stability of viscous fluid with disrupted time-reversal symmetry over a vibrating substrate. Here, the vibration of the bottom substrate is assumed to occur in both streamwise and cross-streamwise directions, with identical frequencies. Numerous methodologies have recently emerged for the implementation of laboratory-on-a-chip applications using microfluidic devices designed for fluid transport. One potential technique involves fluid movement through the application of oscillations of the bounding wall with the breaking of time-reversal symmetry. Thus, the current flow model can be regarded as a prospective approach for the development of microfluidic devices. Besides, utilizing the patterns generated by Faraday waves allows for the creation of structured surfaces, offering applications in the fabrication of patterned materials. These materials find practical use in fields such as optics, sensors, and other technological applications.

The modified time-dependent OS BVP of the current fluid flow model is obtained by applying the classical normal mode approach to the linear perturbation equations imposed on the unsteady base flow solution. The time-dependent OS BVP is numerically solved utilizing the Chebyshev spectral collocation within the framework of Floquet theory. The following is the manuscript’s layout: Section 2 delineates the governing equations associated with the boundary conditions. Next, Section 3 contains the derivation of the time-dependent OS BVP including the numerical approach. A detailed discussion of the numerical outcomes is introduced in Section 5, and finally, a conclusion is made in Section 6.

Mathematical Formulation

To formulate the equations of the problem in the Cartesian coordinate system, the origin OO is considered at the midway of the undisturbed liquid layer of thickness 2d2d. The coordinates xx and yy are selected along the flow direction and the vertically upwards direction, respectively. The bounding wall is assumed to have sinusoidal oscillation in both directions streamwise and cross-streamwise with unique frequency ω\omega. Moreover, the viscous fluid disrupts the time-reversal symmetry, which introduces an additional viscosity coefficient, known as odd or Hall viscosity, to the Cauchy stress tensor. Henceforth, the Cauchy stress tensor T\mathcal{T} is of the following form:

T=Te+To,(1)\mathcal{T}=\mathcal{T}^{e}+\mathcal{T}^{o}, \tag*{(1)}

where the usual (even) part Te\mathcal{T}^{e} corresponds to the typical (even) viscosity μe\mu_{e}, while the odd part To\mathcal{T}^{o} is associated with the odd (Hall) viscosity μo\mu_{o} appeared owing to the breaking of time-reversal symmetry.

The above Eq. (1) can be represented [15, 19] as:

Tije=−pδij+μe(∂xjui+∂xiuj),i,j=1,2,(2)\mathcal{T}_{ij}^{e}=-p\delta_{ij}+\mu_{e}\left(\partial_{x_{j}}u_{i}+\partial_{x_{i}}u_{j}\right),\quad i,j=1,2, \tag*{(2)}
Tijo=−μo[(δi1δj1−δi2δj2)(∂x2u1+∂x1u2)−(δi1δj2+δi2δj1)(∂x1u1−∂x2u2)],i,j=1,2,(3)\mathcal{T}_{ij}^{o}=-\mu_{o}\left[\left(\delta_{i1}\delta_{j1}-\delta_{i2}\delta_{j2}\right)\left(\partial_{x_{2}}u_{1}+\partial_{x_{1}}u_{2}\right)-\left(\delta_{i1}\delta_{j2}+\delta_{i2}\delta_{j1}\right)\left(\partial_{x_{1}}u_{1}-\partial_{x_{2}}u_{2}\right)\right],\quad i,j=1,2, \tag*{(3)}

where δij\delta_{ij} indicates the Kronecker delta with xix_{i}-directed velocity component uiu_{i}. The fluid flow model is specified by choosing (x1,x2)(x_{1},x_{2}) and (u1,u2)(u_{1},u_{2}) as (x,y)(x,y) and (u,v)(u,v), respectively.

In the Cartesian coordinate systems, the continuity and modified Navier-Stokes equations representing the motion of an odd viscosity-induced viscous and incompressible fluid over an inclined vibrating wall can be written in the form:

∂xu+∂yv=0,(4)\partial_{x}u+\partial_{y}v=0, \tag*{(4)}
ρ(∂tu+u ∂xu+v ∂yu)=−∂xp+μe(∂xxu+∂yyu)−μo(∂xxv+∂yyv)+ρgsin⁡α−ρAxω2sin⁡(ωt),(5)\rho\left(\partial_{t}u+u\,\partial_{x}u+v\,\partial_{y}u\right)=-\partial_{x}p+\mu^{e}\left(\partial_{xx}u+\partial_{yy}u\right)-\mu^{o}\left(\partial_{xx}v+\partial_{yy}v\right)+\rho g\sin\alpha-\rho A_{x}\omega^{2}\sin(\omega t), \tag*{(5)}
ρ(∂tv+u ∂xv+v ∂yv)=−∂yp+μe(∂xxv+∂yyv)−μo(∂xxu+∂yyu)−ρgcos⁡α−ρAyω2sin⁡(ωt),(6)\rho\left(\partial_{t}v+u\,\partial_{x}v+v\,\partial_{y}v\right)=-\partial_{y}p+\mu^{e}\left(\partial_{xx}v+\partial_{yy}v\right)-\mu^{o}\left(\partial_{xx}u+\partial_{yy}u\right)-\rho g\cos\alpha-\rho A_{y}\omega^{2}\sin(\omega t), \tag*{(6)}

where gg signifies the acceleration due to gravity and pp represents the fluid pressure. Due to the vibration of the bottom wall in the streamwise and cross-streamwise directions, extra acceleration Axω2sin⁡(ωt)A_{x}\omega^{2}\sin\left(\omega t\right) and Ayω2sin⁡(ωt)A_{y}\omega^{2}\sin\left(\omega t\right) related to the d’Alembert’s body force are included in the xx- and yy- momentum Eqs. 5 and 6, respectively, where AxA_{x} and AyA_{y} denote the forcing amplitudes of streamwise and cross-streamwise oscillations, respectively.

The kinematic boundary condition at the fluid surface yields

v=∂th+u ∂xhaty=h(x,t),(7)v=\partial_{t}h+u\,\partial_{x}h\quad\text{at}\quad y=h(x,t), \tag*{(7)}

The dynamic condition possesses a stress balance at the fluid surface. The form of tangential stress at the free surface [23, 24, 19] is

μe[{1−(∂xh)2}(∂yu+∂xv)−2(∂xu−∂yv)∂xh]+μo[(∂xu−∂yv){1−(∂xh)2}+2(∂yu+∂xv)∂xh]=0aty=h(x,t).(8)\mu^{e}\left[\left\{1-\left(\partial_{x}h\right)^{2}\right\}\left(\partial_{y}u+\partial_{x}v\right)-2\left(\partial_{x}u-\partial_{y}v\right)\partial_{x}h\right]+\mu^{o}\left[\left(\partial_{x}u-\partial_{y}v\right)\left\{1-\left(\partial_{x}h\right)^{2}\right\}+2\left(\partial_{y}u+\partial_{x}v\right)\partial_{x}h\right]=0\quad\text{at}\quad y=h(x,t). \tag*{(8)}
Geometry of gravity-driven liquid over a vibrating plane with broken time-reversal symmetry

Figure 1. Geometry of gravity-driven liquid over a vibrating plane with broken time-reversal symmetry.

The normal stress jump boundary condition [25, 26, 27] at the liquid surface yields

p−pa=11+(∂xh)2[2μe{∂xu(∂xh)2−(∂yu+∂xv)∂xh+∂yv}+μo{(∂yu+∂xv)[1−(∂xh)2]−2(∂xu−∂yv)∂xh}]−σ∂xxh{1+(∂xh)2}32at y=h(x,t),(9)p-p_a=\frac{1}{1+(\partial_xh)^2}\left[2\mu^{e}\left\{\partial_xu(\partial_xh)^2-(\partial_yu+\partial_xv)\partial_xh+\partial_yv\right\}+\mu^{o}\left\{(\partial_yu+\partial_xv)\left[1-(\partial_xh)^2\right]-2(\partial_xu-\partial_yv)\partial_xh\right\}\right]-\sigma\frac{\partial_{xx}h}{\left\{1+(\partial_xh)^2\right\}^{\frac{3}{2}}}\quad\text{at }y=h(x,t), \tag*{(9)}

where pap_a denotes the constant atmospheric pressure and σ\sigma denotes the surface tension. The boundary conditions are the no-slip and no-penetration on the rigid plane, i.e.,

u=0andv=0at y=−d.(10)u=0\quad\text{and}\quad v=0\quad\text{at }y=-d. \tag*{(10)}

The dimensionless forms of Eqs. 4-10 are obtained using the following dimensionless variables:

xˉ=xd,yˉ=yd,uˉ=uωd,vˉ=vωd,tˉ=tω,pˉ=pρω2d2,hˉ=hd,ax=Axd,\bar{x}=\frac{x}{d},\quad\bar{y}=\frac{y}{d},\quad\bar{u}=\frac{u}{\omega d},\quad\bar{v}=\frac{v}{\omega d},\quad\bar{t}=t\omega,\quad\bar{p}=\frac{p}{\rho\omega^2d^2},\quad\bar{h}=\frac{h}{d},\quad a_x=\frac{A_x}{d},
ay=Ayd,μH=μoμe.(11)a_y=\frac{A_y}{d},\quad\mu_H=\frac{\mu^o}{\mu^e}. \tag*{(11)}

Upon substituting the Eq. (11) into Eqs. (4)-(10), the resulting governing equations, and the boundary conditions (after suppressing the over bars) in the dimensionless form can be expressed as

∂xu+∂yv=0,(12)\partial_xu+\partial_yv=0, \tag*{(12)}
Re[∂tu+u ∂xu+v ∂yu]=−Re ∂xp+(∂xxu+∂yyu)−μH(∂xxv+∂yyv)−Re axsin⁡t,(13)Re\left[\partial_tu+u\,\partial_xu+v\,\partial_yu\right]=-Re\,\partial_xp+(\partial_{xx}u+\partial_{yy}u)-\mu_H(\partial_{xx}v+\partial_{yy}v)-Re\,a_x\sin t, \tag*{(13)}
Re[∂tv+u ∂xv+v ∂yv]=−Re ∂yp+(∂xxv+∂yyv)+μH(∂xxu+∂yyu)−ReFr2−Re aysin⁡(t),(14)Re\left[\partial_tv+u\,\partial_xv+v\,\partial_yv\right]=-Re\,\partial_yp+(\partial_{xx}v+\partial_{yy}v)+\mu_H(\partial_{xx}u+\partial_{yy}u)-\frac{Re}{Fr^2}-Re\,a_y\sin(t), \tag*{(14)}
v=∂th+u ∂xhat y=h(x,t),(15)v=\partial_th+u\,\partial_xh\quad\text{at }y=h(x,t), \tag*{(15)}
{[1−(∂xh)2](∂yu+∂xv)−2(∂xu−∂yv)∂xh}+μH{(∂xu−∂yv)[1−(∂xh)2]+2(∂yu+∂xv)∂xh}=0\left\{\left[1-(\partial_xh)^2\right](\partial_yu+\partial_xv)-2(\partial_xu-\partial_yv)\partial_xh\right\}+\mu_H\left\{(\partial_xu-\partial_yv)\left[1-(\partial_xh)^2\right]+2(\partial_yu+\partial_xv)\partial_xh\right\}=0
at y=h(x,t),(16)\text{at }y=h(x,t), \tag*{(16)}
p−pa=1Re{1+(∂xh)2}[2{∂xu(∂xh)2−(∂yu+∂xv)∂xh+∂yv}+μH{(∂yu+∂xv){1−(∂xh)2}p-p_a=\frac{1}{Re\{1+(\partial_xh)^2\}}[2\{\partial_xu(\partial_xh)^2-(\partial_yu+\partial_xv)\partial_xh+\partial_yv\}+\mu_H\{(\partial_yu+\partial_xv)\{1-(\partial_xh)^2\}
[−2(∂xu−∂yv)∂xh]−We∂xxh{1+(∂xh)2}3/2at y=h(x,t),(17)\left[-2(\partial_x u-\partial_y v)\partial_x h\right]-We\frac{\partial_{xx}h}{\left\{1+(\partial_x h)^2\right\}^{3/2}} \quad\text{at } y=h(x,t), \tag*{(17)}

u=0u=0 and v=0v=0 at y=−1y=-1.

The ratio of odd to even viscosity coefficient is symbolized by the new term μH=μoμe\text{The ratio of odd to even viscosity coefficient is symbolized by the new term }\mu_H=\frac{\mu^o}{\mu^e}

renamed it as odd or Hall viscosity coefficient, where the Reynolds number

Re=ρω2d2μeRe=\frac{\rho\omega^2d^2}{\mu^e}

addresses the impact forcing frequency, the Froude number

Fr=ωdgdFr=\frac{\omega d}{\sqrt{gd}}

is the gravity effect, and the surface tension effect is denoted by the Weber number

We=σρω2d3.We=\frac{\sigma}{\rho\omega^2d^3}.

The equations of motion including the boundary conditions for the mean flow with uniform film thickness are given by

∂tUb=sin⁡αFr2+1Re∂yyUb−axsin⁡t,(18)\partial_t U_b=\frac{\sin\alpha}{Fr^2}+\frac{1}{Re}\partial_{yy}U_b-a_x\sin t, \tag*{(18)}
∂yPb=μHRe∂yyUb−cos⁡αFr2−aysin⁡(t),(19)\partial_y P_b=\frac{\mu_H}{Re}\partial_{yy}U_b-\frac{\cos\alpha}{Fr^2}-a_y\sin(t), \tag*{(19)}
∂yUb=0andPb−pa=μHRe∂yUbat y=1,(20)\partial_y U_b=0\quad\text{and}\quad P_b-p_a=\frac{\mu_H}{Re}\partial_y U_b\quad\text{at }y=1, \tag*{(20)}
Ub=0at y=−1,(21)U_b=0\quad\text{at }y=-1, \tag*{(21)}

where pa=pρω2H2p_a=\frac{p}{\rho\omega^2H^2} stands for the nondimensional ambient pressure. The above unsteady base flow Eqs. (18)–(21) for an unperturbed parallel flow is solved analytically, and its exact solutions take the following form

Ub(y,t)=Resin⁡α2Fr2(3+2y−y2)+axcos⁡t−axR[F(y,t)](22)U_b(y,t)=\frac{Re\sin\alpha}{2Fr^2}(3+2y-y^2)+a_x\cos t-a_x\mathcal{R}\left[F(y,t)\right] \tag*{(22)}

and

Pb(y,t)=pa+[cos⁡αFr2+μHFr2sin⁡α+aysin⁡(t)](1−y)−μHReax(R[J(y,t)]),(23)P_b(y,t)=p_a+\left[\frac{\cos\alpha}{Fr^2}+\frac{\mu_H}{Fr^2}\sin\alpha+a_y\sin(t)\right](1-y)-\frac{\mu_H}{Re}a_x\left(\mathcal{R}\left[J(y,t)\right]\right), \tag*{(23)}

where

F(y,t)=cosh⁡{β(1+i)(y−1)}cosh⁡{2β(1+i)}exp⁡(it),J(y,t)=∂yF(y,t),F(y,t)=\frac{\cosh\left\{\beta(1+i)(y-1)\right\}}{\cosh\left\{2\beta(1+i)\right\}}\exp(it),\quad J(y,t)=\partial_yF(y,t),

and the real part of the complex function is defined by R[ … ]\mathcal{R}[\,\ldots\,].

Time-dependent Orr-Sommerefeld boundary value problem

The time-dependent OS BVP is obtained by assuming an infinitesimal perturbation of the unsteady, unidirectional parallel flow solution. A thorough derivation of the time-dependent OS BVP is described by seminal work of Woods and Lin [1] and Samanta [9, 11]. For the current fluid flow model, the time-dependent OS BVP can formulated in the following form:

Re(∂tϕ′′−k2∂tϕ)=(ϕ′′′′−2k2ϕ′′+k4ϕ)−ikRe[Ub(ϕ′′−k2ϕ)−Ub′′ϕ]=0,(24)Re\left(\partial_t\phi^{\prime\prime}-k^2\partial_t\phi\right)=\left(\phi^{\prime\prime\prime\prime}-2k^2\phi^{\prime\prime}+k^4\phi\right)-ikRe\left[U_b\left(\phi^{\prime\prime}-k^2\phi\right)-U_b^{\prime\prime}\phi\right]=0, \tag*{(24)}
(ϕ′′+k2ϕ+2ikμHϕ′)+(Ub′′+2ikμHUb′)η=0at y=1,(25)\left(\phi^{\prime\prime}+k^2\phi+2ik\mu_H\phi^{\prime}\right)+\left(U_b^{\prime\prime}+2ik\mu_H U_b^{\prime}\right)\eta=0\quad\text{at }y=1, \tag*{(25)}
Re ∂tϕ′=[−ikRe{cos⁡αFr2+aysin⁡(t)+μHsin⁡αFr2+axμHReR[D(t)]}−2k2Ub′−ikμHUb′′−ik3We Re η+ϕ′′′−3k2ϕ′−2ik3μHϕ−ikRe[Ubϕ′−Ub′ϕ]]=0at y=1,(26)Re\,\partial_t\phi^{\prime}=\left[-ikRe\left\{\frac{\cos\alpha}{Fr^2}+a_y\sin(t)+\frac{\mu_H\sin\alpha}{Fr^2}+\frac{a_x\mu_H}{Re}\mathcal{R}[\mathcal{D}(t)]\right\}-2k^2U_b^{\prime}-ik\mu_H U_b^{\prime\prime} -ik^3We\,Re\,\eta+\phi^{\prime\prime\prime}-3k^2\phi^{\prime}-2ik^3\mu_H\phi-ikRe\left[U_b\phi^{\prime}-U_b^{\prime}\phi\right]\right]=0\quad\text{at }y=1, \tag*{(26)}
∂tη=−ikUbη−ikϕat y=1,(27)\partial_t\eta=-ikU_b\eta-ik\phi\quad\text{at }y=1, \tag*{(27)}
ϕ′=0andϕ=0at y=−1,(28)\phi^{\prime}=0\quad\text{and}\quad\phi=0\quad\text{at }y=-1, \tag*{(28)}

where the prime symbol ′' stands for the differentiation with respect to the independent variable yy and D(t)=2iβ2cosh⁡[2β(1+i)]exp⁡(it)\mathcal{D}(t) = \frac{2i\beta^{2}}{\cosh[2\beta(1+i)]}\exp(it). ϕ(y,t)\phi(y,t) is the amplitude of the perturbation stream function and η(t)\eta(t) is the amplitude of the surface deformation. Here kk defines the wavenumber in the streamwise direction of an infinitesimal disturbance, where the solution of the infinitesimal disturbance adopts the classical normal mode form X~(x,y,t)=X(y,t)exp⁡(ikx)\widetilde{X}(x,y,t) = X(y,t)\exp(ikx), where X(y,t)X(y,t) is the amplitude of the arbitrary perturbed function X~(x,y,t)\widetilde{X}(x,y,t).

Numerical technique

This section briefly focuses on the numerical procedure to solve the time-dependent OS BVP (Eqs. (24)–(28)) associated with the current flow configuration for disturbance of arbitrary wavenumbers. In this study, a distinct numerical method, as discussed by Woods and Lin [1] and Samanta [11], is implemented to resolve the time-dependent OS BVP. Incorporating the Chebyshev spectral collocation method [28], the time-dependent OS BVP (Eqs. (24)–(28)) can be rewritten as

B∂tΘ=AΘ+(Nccos⁡t+Nssin⁡t)Θ,(29)B\partial_t\Theta= A\Theta+ (N_c\cos t + N_s\sin t)\Theta, \tag*{(29)}

where AA, BB, NcN_c, and NsN_s define square matrices of order (m+2)×(m+2)(m+2)\times(m+2) and the column matrix Θ=[ϕ0,ϕ1,ϕ2,…,ϕm,η]T\Theta= \begin{bmatrix}\phi_0,\phi_1,\phi_2,\ldots,\phi_m,\eta\end{bmatrix}^{T} is of order (m+2)(m+2) with mm Chebyshev modes. Here TT marks the transpose of a matrix. The Folquet theory [5, 10, 29, 11] is employed to solve the Eq. (29). Subsequently, the time-dependent function Θ(t)\Theta(t) can be expansively represented through a truncated complex Fourier series as

Θ(t)=∑n=−KtKtΘnexp⁡[(in+δ)t](30)\Theta(t) = \sum_{n=-\mathcal{K}_t}^{\mathcal{K}_t}\Theta_n\exp[(in+\delta)t] \tag*{(30)}

with constant-coefficient column vectors Θn\Theta_n, the complex Floquet exponent δ=δr+iδi\delta=\delta_r+i\delta_i, and the integers nn and Kt\mathcal{K}_t. Here, the real part δr\delta_r of the Floquet exponent represents the temporal growth rate of the infinitesimal perturbation. Positive values of δr\delta_r signify exponential growth of the disturbance amplitude over time, indicating instability in the corresponding flow. Conversely, if the values of δr\delta_r are negative, the infinitesimal disturbance decays exponentially with time, implying stability in the associated flow. Further, for a given set of parameters, δr=0\delta_r=0 determines the boundary between the stability and instability zones (i.e., the marginal stability curve). Note that, in our study, we have emphasized both harmonic (δi=0\delta_i=0) and subharmonic (δi=1/2\delta_i=1/2) solutions instead of the harmonic solution, generally noticeable in the case of fluid flow down a horizontal vibrating plane. Accumulating the coefficients of exp⁡[(in+δ)t]\exp[(in+\delta)t] from the resulting equation obtained upon the substitution of Eq. (30) into the Eq. (29), a matrix difference equation can be obtained as

[A−(δ+ir)B]Θr+NΘr+1+N∗Θr−1=0,(31)\left[A-(\delta+ir)B\right]\Theta_r+N\Theta_{r+1}+N^{*}\Theta_{r-1}=0, \tag*{(31)}

where N∗N^{*} represents the complex conjugate of N=Nc+iNs2N=\frac{N_c+iN_s}{2}. Equation (32) is a linear system with respect to the variables Θr+1\Theta_{r+1}, Θr\Theta_r and Θr−1\Theta_{r-1}, where coefficients refers to the square matrices. The linear system Eq. (31) can be recast as a generalized matrix eigenvalue problem

FY=δGY.(32)\mathcal{F}\mathcal{Y}=\delta\mathcal{G}\mathcal{Y}. \tag*{(32)}

Here, the Floquet exponent δ\delta is the eigenvalue, Y=[Θ−Kt,Θ−(Kt−1),Θ−(Kt−2),…,ΘKt−2,ΘKt−1,ΘKt]\mathcal{Y}=\begin{bmatrix}\Theta_{-\mathcal{K}_t},\Theta_{-(\mathcal{K}_t-1)},\Theta_{-(\mathcal{K}_t-2)},\ldots,\Theta_{\mathcal{K}_t-2},\Theta_{\mathcal{K}_t-1},\Theta_{\mathcal{K}_t}\end{bmatrix} is the column matrix, F\mathcal{F} is the block tri-diagonal matrix, and G\mathcal{G} is the block diagonal matrix. The forms of F\mathcal{F} and G\mathcal{G} are mentioned in the Appendix A.

Numerical results

In this section, we have discussed the dynamics and instability mechanisms of different existing unstable modes in the current flow problem when the reversal symmetry of time breaks. In Figure 2(a), the marginal stability curve in the (k,αx)(k,\alpha_x)-plane is displayed when μH=0\mu_H=0, ay=0.1a_y=0.1, We=0.016We=0.016, Fr2=100Fr^2=100, Re=5Re=5, and α=90∘\alpha=90^\circ. The symbols ‘U’ and ‘S’ are incorporated to define the unstable and stable zones, respectively. Here, only the normal oscillation of the bottom wall is considered (i.e., ay≠0a_y\ne0 and ax=0a_x=0). The marginal curve well matches the result presented by Woods and Lin [1] when the negligible odd-viscosity coefficient μH\mu_H is taken into account. Figure 2(a) illustrates the emergence of three distinct unstable zones delineating gravitational, subharmonic (SH), and harmonic (H) instability when μH=0\mu_H = 0. Gravitational instability manifests in the longwave range, whereas SH and H unstable zones occur within the finite wavenumber range ([1, 11]). The tongue-shaped patterns of unstable SH and H regions are identified in the wide range of unstable wavenumbers, where the first H tongue is higher compared to the first SH tongue. Initially, the SH instability is responsible for the generation of resonant waves. Thus, in the absence of broken time-reversal symmetry (i.e., μH=0\mu_H = 0), the change in the forcing amplitude in cross-stream oscillation resonates SH and H instabilities in different unstable regions of wavenumber. The stable region between gravitational and SH instabilities is enhanced for the presence of the odd viscosity μH\mu_H in the fluid flow. Consequently, the inclusion of the odd viscosity coefficient μH\mu_H decelerates the transition process from gravitational to SH instability. Further, the odd viscosity μH\mu_H attenuates the stable zone between the SH and H instability emerging in the finite wavenumber range, and this stable zone entirely vanishes for μH≥1\mu_H \ge1. This fact fastens the transition from SH to H instability. Moreover, for a low forcing amplitude of the cross-stream oscillation, the corresponding growth rate result related to the gravitational instability, shown in Figure 2(b), displays a slowdown of the maximum growth rate as μH\mu_H goes up. As a result, a higher odd viscosity μH\mu_H possesses the capacity to delay the transition from gravitational instability to turbulence.

Figure 2. Variation of (a) the instability boundary lines in the (k,ax)(k, a_x)-plane and (b) the corresponding growth rate δr\delta_r related to the gravitational instability with ay=0.1a_y = 0.1 when the odd-viscosity coefficient μH\mu_H varies. Black, red, blue, green, and magenta lines are the results for μH=0\mu_H = 0, μH=0.05\mu_H = 0.05, μH=1\mu_H = 1, μH=2\mu_H = 2, and μH=3\mu_H = 3, respectively. Remaining parameter values are ax=0a_x = 0, We=0.016We = 0.016, Fr2=100Fr^2 = 100, Re=5Re = 5, and α=90∘\alpha= 90^\circ. The red-filled circles are the results of Woods and Lin [1].

Also, to detect the behavior of Faraday waves, the temporal growth rate (δr\delta_r) associated with Figure 2(a), is demonstrated with different forcing amplitudes aya_y (see, Figure 3(a) for ay=1a_y = 1 and Figure 3(b) for ay=6a_y = 6). When ay=1a_y = 1, the growth rate, as in Figure 3(a), displays the sole hump related to SH instability emerging in the finite wavenumber zone. The odd viscosity coefficient μH\mu_H decreases the maximum growth rate of SH instability, thereby exerting a stabilizing effect. On the other hand, upon increasing the forcing amplitude to ay=6a_y = 6, the temporal growth profile unveils a new hump related to H instability (see, Figure 3(b)), including SH instability. The wavenumber of H instability is much greater than the wavenumber of the first SH instability, whereas H instability is much stronger than SH instability. The higher odd viscosity lowers the maximum growth rate of both SH and H instabilities and promotes the stabilizing impact on those instabilities.

Figure 3. Variation of the temporal growth rate δr\delta_r with varying μH\mu_H when (a) ay=2a_y = 2 and (b) ay=6a_y = 6. Black, red, blue, green, and magenta lines are the results for μH=0\mu_H = 0, μH=0.05\mu_H = 0.05, μH=1\mu_H = 1, μH=2\mu_H = 2, and μH=3\mu_H = 3, respectively. Remaining parameter values are ax=0a_x = 0, We=0.016We = 0.016, Fr2=100Fr^2 = 100, Re=5Re = 5, and α=90∘\alpha= 90^\circ.

In Figure 4, the neural stability curves in the (Re,k)(Re, k) plane with different odd viscosity parameters μH\mu_H are demonstrated when the bottom wall solely oscillates in the streamwise direction (i.e., ax≠0a_x \ne0 and ay=0a_y = 0). When μH=0\mu_H = 0 (i.e., the time-reversal symmetry does not break), three different unstable regions emerge that separate the stable range of Reynolds number, where the first two unstable regions I and II are generated because of the bottom wall’s streamwise oscillation, and the unstable region III is instigated by the gravity driving force. That means the gravitational instability is not only responsible for driving the fluid flow’s primary instability but also the resonated instability caused by the streamwise oscillation of the bottom wall. Another important fact is that the higher values of odd viscosity enhance the stable zone of Reynolds number generated among the separated unstable zones I, II, and III. Consequently, the higher odd viscosity slows the transition process from resonance to gravitational instabilities. Further, at lower ReRe values, the resonated unstable region dominates the gravitational instability region. The unstable zones associated with the resonance and gravity waves shrink with the increasing values of μH\mu_H, leading to a stabilizing influence on these unstable zones.

Figure 4. Variation of (a) the instability boundary curves in the (Re−k)(Re-k)-plane with varying μH\mu_H. Black, red, blue, green, and magenta lines are the results for μH=0\mu_H = 0, μH=0.05\mu_H = 0.05, μH=1\mu_H = 1, μH=2\mu_H = 2, and μH=3\mu_H = 3, respectively. Remaining parameter values are ax=6a_x = 6, ay=0a_y = 0, We=0.016We = 0.016, Fr=100Fr = 100, and α=90∘\alpha= 90^\circ.

In order to clarify the above fact, the associated growth rate curves are displayed in Figure 5 related to the resonated unstable regions I (see, Figure 5(a) for Re=2Re = 2) and II (see, Figure 5(b) for Re=12Re = 12) and for the unstable region III (see Figure 5(c) for Re=35Re = 35). The values of ReRe are chosen from the unstable region, as depicted in Figure 4. It is identified that the growth rates associated with resonated instabilities I, as in Figure 5(a), and II, as in Figure 5(b) in the finite wave number range diminishes for higher odd viscosity μH\mu_H. However, for a sufficiently higher value Re=35Re = 35, the gravitational instability arises in the longwave region, and the corresponding growth rate attenuates as soon as μH\mu_H increases. These outcomes entirely agree with the result of Figure 4. Thus, the odd viscosity has the potential to stabilize the resonated instability along with the gravitational instability generated in the falling liquid film over an oscillating plane when the time-reversal symmetry breaks.

Figure 5. Variation of the temporal growth rate δr\delta_r with varying μH\mu_H when (a) Re=2Re = 2, (b) Re=12Re = 12, and (c) Re=35Re = 35. Black, red, blue, green, and magenta lines are the results for μH=0\mu_H = 0, μH=0.05\mu_H = 0.05, μH=1\mu_H = 1, μH=2\mu_H = 2, and μH=3\mu_H = 3, respectively. Remaining parameter values are ax=6a_x = 6, ay=0a_y = 0, We=0.016We = 0.016, Fr=100Fr = 100, and α=90∘\alpha= 90^\circ.

Also, we have tracked out the effect of the angle of inclination α\alpha of the bounding wall on the resonated instability owing to the oscillation of the bottom substrate and gravitational instabilities. Figure 6 represents the neutral stability curves in Re−kRe-k plane for different inclination angles α\alpha when both cases (i) lateral (see, Figure 6(a)) and (ii) normal (see, Figure 6(b)) oscillations are individually considered. As in Figure 6(a), When ax=6a_x = 6 and ay=0a_y = 0 (i.e., only the streamwise oscillation of the bounding wall), no noticeable deviation in the resonance curves is observed with the varying angle α\alpha, whereas the gravitational instability emerging in the longwave region drastically shrinks, followed by the increasing of the critical Reynolds number. On the other hand, for ax=0a_x = 0 and ay=1a_y = 1 (i.e., only the normal oscillation of the bounding wall), the inclination angle α\alpha has negligible impact on the instability regions corresponding to the resonance waves (see, Figure 6(b)), while, as expected, the gravitational instability regions significantly attenuate as soon as the values of α\alpha reduce. Thus, the influence of the angle of inclination is only perceptible for gravitational instability, whereas parametric resonances experience a very weak impact.

Figure 6. Variation of the instability boundary lines in the (Re−kRe-k)− plane with varying α\alpha when (a) ax=6a_x = 6 and ay=0a_y = 0, and (b) ax=0a_x = 0 and ay=1a_y = 1. Black, red, blue, and green lines are the results for α=90∘\alpha= 90^\circ, α=70∘\alpha= 70^\circ, α=50∘\alpha= 50^\circ, and α=30∘\alpha= 30^\circ, respectively. Remaining parameter values are μH=0.05\mu_H = 0.05, We=0.016We = 0.016 and Fr2=100Fr^2 = 100.

Figure 7 displays the continuation of Figure 2 for sufficiently increasing the Reynolds number Re=20Re=20. The stability boundary line demonstrates that the resonated waves form a tongue-like pattern in the absence of broken-time reversal symmetry. It is observed that gravitational instability increases for sufficiently high inertia force. Also, the unstable zone of the SH and H instabilities enhances for higher value Re=20Re=20 by reducing the critical forcing amplitudes for the first SH and first H instabilities. Note that, when the time-reversal symmetry breaks (i.e., μH≠0\mu_H \ne0) the stable region of sufficiently higher wavenumbers between SH and H instabilities vanishes, making the transition process from SH to H instability faster. Physically, one can produce SH and H instabilities, comparatively, at lower forcing amplitudes aya_y for a cross-stream oscillatory odd-viscosity-induced fluid flow. Moreover, a higher value of odd viscosity reduces the unstable zone of gravitational instability by dissipating gravity waves. Consequently, higher odd viscosity enhances the stable range between gravitational and SH instabilities and weakens the transition process from gravitational instability to SH instability.

Continuation of Fig. 2

Figure 7. Variation of (a) the instability boundary lines in the (ay−k)(a_y-k)-plane with varying μH\mu_H. Black, red, blue, and green lines are the results for μH=0\mu_H=0, μH=1\mu_H=1, μH=2\mu_H=2, and μH=3\mu_H=3, respectively. Remaining parameter values are Re=20Re=20, ax=0a_x=0, We=0.016We=0.016, Fr2=100Fr^2=100, and α=90∘\alpha=90^\circ.

The corresponding temporal growth rate curves with different μH\mu_H are plotted in Figure 8 when the forcing amplitude ay=1a_y=1, as in Figure 8(a) and ay=3a_y=3, as in Figure 8(b). Figure 8(a) depicts two humps, where the growth rate of both gravitational and SH instabilities decrease as long as odd viscosity increases. This fact assures that a higher value of odd viscosity can weaken both gravitational and SH instabilities. On the other side, for a comparatively higher forcing amplitude of the cross-stream oscillation (ay=3a_y=3), the growth rate curve displays three humps instead of two humps, which is fully consistent with the neutral curve results in Figure 7. The new hump in the finite wavenumber region corresponds to the H instability, which diminishes with an increasing value of odd viscosity μH\mu_H.

Figure 8. Variation of the temporal growth rate δr\delta_r with varying μH\mu_H when (a) ay=1a_y = 1 and (b) ay=3a_y = 3 with Re=20Re = 20. Black, red, blue, and green lines are the results for μH=0\mu_H = 0, μH=1\mu_H = 1, μH=2\mu_H = 2, and μH=3\mu_H = 3, respectively. Remaining parameter values are ax=0a_x = 0, We=0.016We = 0.016, Fr2=100Fr^2 = 100, and α=90∘\alpha= 90^\circ.

Now, the neutral stability curve for different odd viscosity is demonstrated in Figure 9 to understand the instability behavior of Faraday waves when the liquid layer is comparatively thick with high surface tension and low inclination angle. The SH and H unstable regions are displayed alternatively in this tongue-like unstable region when the odd viscosity coefficient is absent. It is to be noted that, the neutral stability curve does not occur in the gravitational unstable region. The reason is that the Reynolds number belongs to the stable zone. Once, the odd viscosity is introduced in the liquid film, the stable zones in the finite wavenumber range between the SH and H instability fully disappear. The critical forcing amplitudes for the SH and H tongues attenuate for a higher value of odd viscosity. However, the critical forcing

Figure 9. Variation of the instability boundary lines in the (ay−k)(a_y-k)-plane with varying μH\mu_H. Black, red, blue, and green lines are the results for μH=0\mu_H = 0, μH=1\mu_H = 1, μH=2\mu_H = 2, and μH=3\mu_H = 3, respectively. Remaining parameter values are Re=20Re = 20, ax=0a_x = 0, We=0.16We = 0.16, Fr2=100Fr^2 = 100, and α=1∘\alpha= 1^\circ.

amplitude for the first SH tongue always remains lower than that for the first H tongue. Therefore, introducing lower forcing amplitudes makes it possible to create SH and H resonances in the odd-viscosity-induced thinner-layered liquid with high surface tension flowing down a slightly inclined oscillating plane.

To make this result portrayed in Figure 9 consistent, the associated temporal growth rate result is plotted in Figure 10 for different odd viscosity parameters with various forcing amplitudes of the cross-stream oscillation of the bounding wall. As expected, for lower forcing amplitude ay=1a_y = 1 of cross-stream oscillation, gravitational instability is absent in the temporal growth rate profile (see, Figure 10(a)), whereas the SH instability appears and reduces with higher odd viscosity. However, for comparatively higher forcing amplitude ay=3a_y = 3, both SH and H instabilities arise (see, Figure 10(a)) in the wide range of finite wavenumbers, and both types of instability diminish with the increasing value of odd viscosity. Therefore, the resonated waves generated at the liquid surface can be weakened owing to the higher odd viscosity value. These facts totally validate the findings pertained in Figure 9.

Figure 10. Variation of the temporal growth rate δr\delta_r with varying μH\mu_H when (a) ay=1a_y = 1 and (b) ay=3a_y = 3. Black, red, blue, and green lines are the results for μH=0\mu_H = 0, μH=1\mu_H = 1, μH=2\mu_H = 2, and μH=3\mu_H = 3, respectively. Remaining parameter values are ax=0a_x = 0, We=5We = 5, Re=10Re = 10, Fr2=1Fr^2 = 1, and α=1∘\alpha= 1^\circ.

To detect the behavior of Faraday waves with different odd viscosity coefficients μH\mu_H for falling thin film under high inertia force, with high surface tension flowing down a slightly inclined plane, Figure 11 is plotted by choosing We=5We = 5, Fr=1Fr = 1, Re=290Re = 290, and α=1∘\alpha= 1^\circ (Woods and Lin [1]). The novelty that emerges from Figure 11 is that there are two humps in the temporal growth rate result with no external oscillatory forcing (see, Figure 11(a) for ay=0a_y = 0): one is related to gravitational instability in the longwave region, and the other is shear instability in the finite wavenumber range. Thus, the shear mode instability at the liquid surface is observed when the Reynolds number is chosen sufficiently high with a small inclination angle of the bottom wall. The emergence of shear instability is owing to the Reynolds number exceeding its critical level. Here, as μH\mu_H increases, the growth rate decreases for the gravity and shear waves. On the other hand, as long as the external cross-stream oscillation is incorporated (see, Figure 11(b) for ay=3a_y = 3), both SH and H resonated instability arise in the temporal growth along with the gravitational and shear instabilities. A higher value of odd viscosity weakens all these different types of instability emerging in the flow system by attenuating the corresponding growth rates.

Figure 11. Variation of the temporal growth rate δr\delta_r with varying μH\mu_H when (a) ay=0a_y = 0 and (b) ay=3a_y = 3 with Re=290Re = 290. Black, red, blue, and green lines are the results for μH=0\mu_H = 0, μH=10\mu_H = 10, μH=20\mu_H = 20, and μH=30\mu_H = 30, respectively. Remaining parameter values are ax=0a_x = 0, We=5We = 5, Fr2=1Fr^2 = 1, and α=1∘\alpha= 1^\circ.

Now the stability boundary lines with different odd viscosity μH\mu_H are demonstrated in Figure 12 when a thin liquid layer with high surface tension flows down over a cross-streamwise oscillatory slightly inclined substrate. The marginal stability curve shows three different unstable zones gravitational, resonated, and shear instabilities. Higher odd viscosity shrinks the unstable longwave zones of gravitational instability by enhancing the critical Reynolds number. Contrapositively, the shear instability existing in the higher wavenumber range intensifies with the increasing value of the odd viscosity coefficient followed by a successive increase of corresponding unstable zones. However, compared to the gravity and shear instabilities, the odd viscosity has a weak but stabilizing influence on the resonated instability. Thus, the surface wave instability generated by the gravity driving force and the oscillating plane can be weakened by considering higher values of odd viscosity. Next, the associated temporal growth rate curves are shown in Figure 13 pertaining to the change in gravitational instability when Re=40Re = 40 (see, Figure 13(a)) and shear instability when Re=150Re = 150 (see, Figure 13(b)). A decrease in the growth rate, as in Figure 13(a), of the gravitational instability is noticed with higher values of μH\mu_H. This showcases the stabilizing influence of odd viscosity on the gravity-driving instability waves. On the other hand, the higher odd viscosity amplifies the growth rate of the shear instability, as depicted in Figure 13, manifesting in the higher wavenumber range.

Variation of the instability boundary lines

Figure 12. Variation of the instability boundary lines in the (Re−kRe-k)− plane with varying μH\mu_H. Black, red, and blue lines are the results for μH=0\mu_H = 0, μH=1\mu_H = 1, μH=2\mu_H = 2, and μH=3\mu_H = 3, respectively. Remaining parameter values are ax=4a_x = 4, ay=0a_y = 0, We=5We = 5, Fr2=1Fr^2 = 1, and α=1∘\alpha= 1^\circ.

Figure 13. Variation of the temporal growth rate δr\delta_r with varying μH\mu_H when (a) Re=40Re=40 and (b) Re=150Re=150. Black, red, blue, and green lines are the results for μH=0\mu_H=0, μH=1\mu_H=1, μH=2\mu_H=2, and μH=3\mu_H=3, respectively. Remaining parameter values are ax=4a_x=4, ay=0a_y=0, We=5We=5, Fr2=1Fr^2=1, and α=1∘\alpha=1^\circ.

Conclusions

The instability behavior of falling liquid over an inclined plane that is compelled to vibrate in both the streamwise and cross-stream directions with identical frequency is examined when the time-reversal symmetry breaks. The linear stability analysis is performed for arbitrary wavenumbers by numerically solving the corresponding time-dependent OS BVP, including the Floquet theory. The numerical outcomes manifest the occurrence of three different unstable regions: gravitational, SH, and H. In general, gravitational instability emerges in the long-wave range, whereas SH and H instabilities exist in the finite wavenumber regime. In comparison to the generation of H instability, the critical forcing amplitude for the generation of SH instability is smaller. This assures the dominance of SH instability in the finite wavenumber region. When the time-reversal symmetry breaks, i.e., the odd viscosity is introduced to the flow system, a higher value of odd viscosity attenuates the stable region between gravitational and SH instabilities in the longwave range. Also, the stable range located in the finite wavenumber zone between SH and H instabilities entirely disappears as soon as odd viscosity increases. This ensures the occurrence of a transition from SH to H instability rapidly and in a continuous fashion in the finite wavenumber regime when the odd viscosity increases. A comparatively higher inertia force shrinks the unstable region of the SH and H instabilities and consequences more unstable regions of the SH and H waves in an alternative fashion in the marginal curve. Nevertheless, the critical amplitude needed for the first SH instability is always lower compared to the first H instability.

Additionally, shear instability comes into existence together with the gravitational, SH, and H instabilities for a strong interia force with a small angle of inclination. The gravitational and resonance instabilities can be weakened by choosing a higher odd viscosity value, whereas an opposite trend is observed for the shear instability. In view of the above, examining the behavior of surface wave instability of unsteady laminar flow over vibrating inclined plane advances our level of understanding when the time-reversal symmetry breaks in the flow model. A detailed elucidation of the interplay between the time-dependent base state and the odd viscosity emphasizes the importance of considering odd viscosity in the study of flow stability.

Expression of the block tri-diagonal matrix F\mathcal{F} and block diagonal matrix G\mathcal{G}

F=[⋮⋮⋮⋮⋮⋮⋮⋯(A+2iB)N000⋯⋯N∗(A+iB)N00⋯⋯0N∗AN0⋯⋯00N∗(A−iB)N⋯⋯000N∗(A−2iB)⋯⋮⋮⋮⋮⋮⋮⋮]\mathcal{F} = \begin{bmatrix} \vdots& \vdots& \vdots& \vdots& \vdots& \vdots& \vdots\\ \cdots& (\mathcal{A}+2i\mathcal{B}) & \mathcal{N} & 0 & 0 & 0 & \cdots\\ \cdots& \mathcal{N}^{*} & (\mathcal{A}+i\mathcal{B}) & \mathcal{N} & 0 & 0 & \cdots\\ \cdots& 0 & \mathcal{N}^{*} & \mathcal{A} & \mathcal{N} & 0 & \cdots\\ \cdots& 0 & 0 & \mathcal{N}^{*} & (\mathcal{A}-i\mathcal{B}) & \mathcal{N} & \cdots\\ \cdots& 0 & 0 & 0 & \mathcal{N}^{*} & (\mathcal{A}-2i\mathcal{B}) & \cdots\\ \vdots& \vdots& \vdots& \vdots& \vdots& \vdots& \vdots \end{bmatrix}

and

G=[⋮⋮⋮⋮⋮⋮⋮⋯B0000⋯⋯0B000⋯⋯00B00⋯⋯000B0⋯⋯0000B⋯⋮⋮⋮⋮⋮⋮⋮].\mathcal{G} = \begin{bmatrix} \vdots& \vdots& \vdots& \vdots& \vdots& \vdots& \vdots\\ \cdots& \mathcal{B} & 0 & 0 & 0 & 0 & \cdots\\ \cdots& 0 & \mathcal{B} & 0 & 0 & 0 & \cdots\\ \cdots& 0 & 0 & \mathcal{B} & 0 & 0 & \cdots\\ \cdots& 0 & 0 & 0 & \mathcal{B} & 0 & \cdots\\ \cdots& 0 & 0 & 0 & 0 & \mathcal{B} & \cdots\\ \vdots& \vdots& \vdots& \vdots& \vdots& \vdots& \vdots \end{bmatrix}.

Acknowledgment

SG gratefully acknowledges the financial support from SERB, Department of Science and Technology, Government of India through Award No. MTR/2021/000442.

Conflict of Interest

I have no conflict of interest.

Declaration of competing interest

The author declares that he has no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper.

Credit authorship contribution statement

Md. Mouzakkir Hossain: Conceptualization, Methodology, Software, Writing - original draft, Validation, Formal analysis, Investigation. Mrityunjoy Saha: Methodology, Formal analysis, Investigation. Harekrushna Behera: Software, Review & Editing. Sukhendu Ghosh: Conceptualization, Software, Review & Editing.

References

  1. [1]David R Woods and SP Lin. Instability of a liquid film flow over a vibrating inclined plane. Journal of Fluid Mechanics, 294:391–407, 1995.
  2. [2]Chia-Shun Yih. Instability of unsteady flows or configurations part 1. instability of a horizontal liquid layer on an oscillating plane. Journal of Fluid Mechanics, 31(4):737–751, 1968.
  3. [3]BS Dandapat and AS Gupta. Instability of a horizontal layer of viscoelastic liquid on an oscillating plane. Journal of Fluid Mechanics, 72(3):425–432, 1975.DOI
  4. [4]SP Lin, JN Chen, and DR Woods. Suppression of instability in a liquid film flow. Physics of Fluids, 8(12):3247–3252, 1996.DOI
  5. [5]AC Or. Finite-wavelength instability in a horizontal liquid layer on an oscillating plane. Journal of Fluid Mechanics, 335:213–232, 1997.DOI
  6. [6]AC Or and RE Kelly. Thermocapillary and oscillatory-shear instabilities in a layer of liquid with a deformable surface. Journal of Fluid Mechanics, 360:21–39, 1998.DOI
  7. [7]AG Burya and V Ya Shkadov. Stability of a liquid film flowing down an oscillating inclined surface. Fluid Dynamics, 36(5):671–681, 2001.DOI
  8. [8]Peng Gao and Xi-Yun Lu. Effect of surfactants on the long-wave stability of oscillatory film flow. Journal of Fluid Mechanics, 562:345–354, 2006.DOI
  9. [9]A Samanta. Effect of electric field on the stability of an oscillatory contaminated film flow. Physics of Fluids, 21 (11), 2009.DOI
  10. [10]Arghya Samanta. Linear stability of a viscoelastic liquid flow on an oscillating plane. Journal of Fluid Mechanics, 822:170–185, 2017.DOI
  11. [11]A Samanta. Instability of a shear-imposed flow down a vibrating inclined plane. Journal of Fluid Mechanics, 915, 2021.DOI
  12. [12]MK Smith and SH Davis. The instability of sheared liquid layers. Journal of Fluid Mechanics, 121:187–206, 1982.DOI
  13. [13]MK Smith. The mechanism for the long-wave instability in thin liquid films. Journal of Fluid Mechanics, 217:469–485, 1990.DOI
  14. [14]M Sivapuratharasu, S Hibberd, ME Hubbard, and H Power. Inertial effects on thin-film wave structures with imposed surface shear on an inclined plane. Physica D: Nonlinear Phenomena, 325:86–97, 2016.DOI
  15. [15]JE Ayron. Odd viscosity. Journal of statistical physics, 92(3):543–557, 1998.
  16. [16]MF Lapa and TL Hughes. Swimming at low reynolds number in fluids with odd, or hall, viscosity. Physical Review E, 89(4):043019, 2014.pubmed.ncbi.nlm.nih.gov/24827344
  17. [17]E Kirkinis and AV Andreev. Odd-viscosity-induced stabilization of viscous thin liquid films. Journal of Fluid Mechanics, 878:169–189, 2019.DOI
  18. [18]G Bao and Y Jian. Odd-viscosity-induced instability of a falling thin film with an external electric field. Physical Review E, 103(1):013104, 2021.DOI
  19. [19]A Samanta. Role of odd viscosity in falling viscous fluid. Journal of Fluid Mechanics, 938, 2022.DOI
  20. [20]S Chattopadhyay. Odd-viscosity-induced instability of a thin film with variable density. Physics of Fluids, 33(8):082102, 2021.DOI
  21. [21]D Paul, MM Hossain, and H Behera. Hydrodynamic instability of odd-viscosity-induced shear-imposed falling film. Physics of Fluids, 35(3), 2023.DOI
  22. [22]MM Hossain, S Ghosh, and H Behera. Odd-viscosity induced surfactant-laden shear-imposed viscous film over a slippery incline: a stability analysis. Meccanica, pages 1–21, 2024.
  23. [23]HH Wei. Effect of surfactant on the long-wave instability of a shear-imposed liquid flow down an inclined plane. Physics of Fluids, 17(1):012103, 2005.DOI
  24. [24]A Samanta. Shear-imposed falling film. Journal of fluid mechanics, 753:131, 2014.DOI
  25. [25]Anjalaiah, R Usha, and S Millet. Thin film flow down a porous substrate in the presence of an insoluble surfactant: Stability analysis. Physics of Fluids, 25(2):022101, 2013.DOI
  26. [26]FA Bhat and A Samanta. Linear stability for surfactant-laden two-layer film flows down a slippery inclined plane. Chemical Engineering Science, 220:115611, 2020.DOI
  27. [27]M Sani, SA Selvan, S Ghosh, and H Behera. Effect of imposed shear on the dynamics of a contaminated two-layer film flow down a slippery incline. Physics of Fluids, 32(10):102113, 2020.DOI
  28. [28]Peter J Schmid, Dan S Hennigson, Peter J Schmid, and Dan S Henningon. Transition to turbulence. Stability and transition in shear flows, pages 401–475, 2001.DOI
  29. [29]Arghya Samanta. Effect of porous layer on the faraday instability in viscous liquid. Proceedings of the Royal Society A, 476(2239):20200208, 2020.DOI

Paper details

vlnc:W_gtfcww46
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents