betaFeedback

WorksEngineering

Continuous Wideband Multicarrier Rydberg Atomic Quantum Receiver

Abstract

This paper investigates continuous wideband orthogonal frequency-division multiplexing (OFDM) reception using an auxiliary (AUX)-assisted five-level Rydberg atomic quantum receiver (RAQR) with a single microwave local oscillator (LO), without requiring additional atomic reception transitions or LO frequency combs. By exploiting Floquet theory, the proposed framework characterizes the dynamic atomic response at finite signal-LO detunings without relying on a quasi-static Taylor expansion around the LO operating point. Specifically, closed-form radio-frequency (RF)-to-electrical conversion expressions are derived from the Lindblad master equation under weak-probe and weak-signal approximations. Building on these expressions, an equivalent multicarrier communication model is established, revealing the inherent frequency selectivity of the atomic response and the resulting subcarrier-dependent amplitude and phase distortions. RAQR-aware zero-forcing (ZF) equalization is developed to enable reliable OFDM reception. Furthermore, analytical results reveal how LO and AUX driving influence the atomic response through dressed-state splitting and energy-level shifts. An upper bound on the LO-referenced half-power span is derived, and an approximately 1818-dB reduction in center-response power per bandwidth doubling is established in the AUX-free strong-LO regime. Simulation results validate the analytical response model and reveal pronounced subcarrier-dependent amplitude and phase variations across over 1010~MHz, highlighting the potential of RAQRs as wideband receiving front ends for future wireless communications.

Introduction

Sixth-generation (6G) mobile networks are expected to support immersive services, ubiquitous connectivity, and integrated sensing and communication [1, 2, 3]. Realizing these goals requires wider signal bandwidths and reliable weak-signal reception within practical hardware and power budgets [4]. In conventional RF receivers, improving sensitivity may require a larger hardware implementation and higher power consumption, while wider bandwidth increases integrated noise power, making sensitivity harder to maintain within fixed hardware and power budgets [5], [6]. These challenges motivate the exploration of alternative physical mechanisms for wireless reception that complement continued advances in RF circuit design.

Rydberg atomic quantum receivers (RAQRs) offer an alternative reception mechanism by converting RF-induced changes in atomic coherence into optical signals [7]. The large transition dipole moments between Rydberg states enable sensitive interactions with incident RF fields [8]. Specifically, a resonant probe beam is strongly absorbed without a coupling laser, whereas adding the coupling laser under two-photon resonance suppresses absorption and establishes a narrow transmission window, which is known as electromagnetically induced transparency (EIT) [9]. Introducing a sufficiently strong RF field resonant with the transition between two Rydberg states then splits this EIT window into two resolved peaks, producing Autler-Townes splitting (ATS) [10]. Since the peak separation is proportional to the RF-field amplitude, this spectral splitting provides an optical means of measuring the field magnitude. To recover both amplitude and phase of the RF signal, atomic superheterodyne reception introduces a microwave local oscillator (LO) with a small frequency offset relative to the received signal, forming a time-varying optical readout. This superheterodyne architecture enables coherent RF reception for wireless communication networks [11].

Building on these detection mechanisms, RAQR research has progressed from experimental demonstrations of waveform recovery to analytical modeling of communication systems. Early experiments demonstrated reception of amplitude- and frequency-modulated microwave signals [12], [13]. Subsequent work investigated phase-shift-keyed reception [14], quadrature amplitude modulation (QAM) reception [15], and phase-modulated frequency-division multiplexing [16]. To improve robustness against receiver impairments, laser phase-noise compensation was incorporated into optically biased coherent detection [17]. In parallel, frequency-hopping recep-

Q. Peng, Q. Luo, and P. Xiao are affiliated with 5G and 6G Innovation Centre, Institute for Communication Systems (ICS) of the University of Surrey, Guildford, GU2 7XH, UK. (e-mail: {q.peng, q.u.luo,p.xiao}@surrey.ac.uk).

Maged Elkashlan is with Queen Mary University of London, United Kingdom. (E-mail: [email protected]).

Cunhua Pan is with the National Mobile Communications Research Laboratory, Southeast University, Nanjing, China. (e-mail: [email protected]; [email protected]).

George K. Karagiannidis is with the Department of Electrical and Computer Engineering, Aristotle University of Thessaloniki, Thessaloniki 54124, Greece (e-mail: [email protected]).

T. Q. Duong is with the Faculty of Engineering and Applied Science, Memorial University, St. John’s, NL A1C 5S7, Canada and also with the School of Electronics, Electrical Engineering and Computer Science, Queen’s University Belfast, Belfast, U.K. (e-mail: [email protected]) tion was investigated to enhance resilience to jamming by exploiting atomic frequency tunability [18]. Although these demonstrations establish the feasibility of atomic reception, translating this capability into system-level design requires tractable models that link incident electromagnetic signals to the resulting optical responses. To this end, an equivalent baseband model was derived using a Taylor expansion [19]. Subsequently the linear operating regime of this approximate model was characterized in [20]. Building on this model, RAQR-based reception has been investigated in self-sustained networks [21] and satellite communications [22]. These studies highlighted the potential of RAQRs as an alternative receiver technology for next-generation wireless networks.

Despite these advantages, high-sensitivity RAQR reception requires highly stable laser driving and a tightly controlled atomic environment. Fluctuations in laser detuning and power, together with atomic thermal motion, would significantly alter the atomic susceptibility and RF-to-optical conversion gain [23]. Furthermore, for wideband communications, conventional resonance-based RAQRs face two distinct constraints, namely limited instantaneous bandwidth and discontinuous high-sensitivity carrier coverage. The former is governed by optical driving and atomic relaxation dynamics [24], [25], whereas the latter arises from the discrete RF transitions between Rydberg states [26]. Therefore, broad carrier-frequency tunability does not guarantee simultaneous reception over a continuous band. These limitations motivate efforts to extend high-sensitivity carrier coverage and broaden the instantaneous response bandwidth for wideband multicarrier reception.

Several approaches have extended the frequency coverage and instantaneous bandwidth of RAQRs. Multilevel schemes enabled simultaneous reception through distinct Rydberg transitions, but their responses remained concentrated around separated resonances [27], [28]. To achieve continuous multicarrier reception, a five-level scheme combining auxiliary-field detuning with a microwave LO frequency comb was proposed in [29], although comb generation and careful intermediate-frequency allocation increased implementation complexity. Alternatively, six-wave mixing was investigated to broaden the RF-to-optical response through multiphoton interactions [30], [31]. More recently, auxiliary-microwave control was introduced to enhance the instantaneous response of a five-level configuration [32]. Despite these advances, understanding how the broadened atomic response supports continuous multicarrier reception with a single LO, while accounting for its inherent frequency selectivity and gain-bandwidth tradeoff, remains an important challenge.

Although the AUX-assisted five-level configuration in [32] demonstrated wideband microwave sensing, its broadband atomic response does not directly guarantee reliable multicarrier reception. In particular, real-valued IF readout introduces image overlap, while the frequency-selective atomic response causes subcarrier-dependent amplitude and phase distortions. To address these communication-specific challenges, we develop a single-LO OFDM reception framework without requiring an LO frequency comb. By integrating the Floquet-based atomic response with coherent optical detection, an equivalent multicarrier communication model and RAQR-aware equalizers are established. Beyond signal recovery, analytical results characterize the effects of LO and AUX driving on the center conversion gain and usable bandwidth, revealing a fundamental gain–bandwidth tradeoff. The main contributions are summarized as follows:

  • Floquet-based wideband conversion model. Building on the first-order Floquet response of the AUX-assisted five-level configuration, we derive a communication-oriented RF-to-electrical transfer function incorporating coherent optical readout. Unlike quasi-static Taylor expansions around the LO operating point, the proposed model captures finite-frequency atomic dynamics and the resulting amplitude and phase responses. Simulation results validate the derived expressions and demonstrate a one-sided LO-referenced bandwidth over 11 MHz under the considered parameters, highlighting the potential of RAQRs as wideband receiving front ends.

  • Single-LO wideband OFDM reception. We extend the proposed reception scheme to wideband OFDM using a single microwave LO, without an LO frequency comb. An equivalent fast Fourier transform (FFT)-domain input-output model is derived to characterize the inherently frequency-selective atomic response, which introduces subcarrier-dependent amplitude and phase distortions even under a frequency-flat wireless channel. To address these distortions, we develop RAQR-aware frequency-domain equalizers that jointly compensate for the wireless and atomic responses.

  • Analytical characterization of LO/AUX response control. Under the far-detuned AUX approximation, a reduced complex-response model is derived to characterize the resonance locations, modal linewidths, and center atomic conversion gain. The analysis reveals that LO driving controls the dressed-state splitting and linewidths, whereas AUX driving shifts the bright-state resonances and modifies the center response through distinct energy-level shifts. We further establish an explicit condition for AUX-induced gain enhancement, providing analytical guidance for shaping the atomic frequency response.

  • Bandwidth upper bound and gain–bandwidth trade-off. We derive an analytical upper bound on the one-sided LO-referenced bandwidth and establish a quantitative gain-bandwidth tradeoff for the AUX-free case. In the strong-LO regime with a contiguous passband, doubling the bandwidth incurs an approximately 18-dB loss in center-response power, implying an equivalent sensitivity penalty under fixed readout-noise conditions. Simulation results validate the bandwidth bound and corroborate the analyzed gain-bandwidth tradeoff.

The remainder of this paper is organized as follows. Section II presents the five-level atomic model, and Section III derives the optical response and its equivalent multicarrier representation. Section IV analyzes the tradeoff between gain and bandwidth. Section V presents simulation results, and Section VI concludes the paper.

System Model

Five-Level Floquet–Lindblad Model for Atomic Response

In Figure 1, we consider a five-level configuration with the basis {∣1⟩,∣2⟩,∣3⟩,∣4⟩,∣5⟩}\{\lvert1\rangle, \lvert2\rangle, \lvert3\rangle, \lvert4\rangle, \lvert5\rangle\}, where ∣1⟩\lvert1\rangle is the ground state, ∣2⟩\lvert2\rangle represents the excited state, and ∣3⟩\lvert3\rangle, ∣4⟩\lvert4\rangle, and ∣5⟩\lvert5\rangle are Rydberg states. The probe and coupling lasers drive ∣1⟩↔∣2⟩\lvert1\rangle\leftrightarrow\lvert2\rangle and ∣2⟩↔∣3⟩\lvert2\rangle\leftrightarrow\lvert3\rangle with Rabi frequencies Ωp\Omega_p and Ωc\Omega_c. The LO and weak RF signal drive ∣3⟩↔∣4⟩\lvert3\rangle\leftrightarrow\lvert4\rangle with Rabi amplitudes ΩL\Omega_L and Ωs\Omega_s, while the AUX field drives ∣3⟩↔∣5⟩\lvert3\rangle\leftrightarrow\lvert5\rangle with ΩA\Omega_A. The signal-LO angular-frequency offset is δs=ωs−ωL\delta_s = \omega_s - \omega_L, where ωs\omega_s and ωL\omega_L are the angular frequencies of the signal MW and the LO MW, respectively. The angular frequencies of probe, coupling, and AUX MW are denoted as ωp\omega_p, ωc\omega_c, and ωA\omega_A, respectively. Furthermore, the constant phases of the probe, coupling, LO, and AUX fields are absorbed into the atomic basis, allowing their Rabi frequencies to be taken as real and nonnegative. By applying the rotating-wave approximation, the Hamiltonian H(t)H(t) is written as

Continuous wideband RAQR based on a 5-level configuration

Figure 1. Continuous wideband RAQR based on a 5-level configuration.

H(t)=ℏ×[0Ωp2000Ωp2−ΔpΩc2000Ωc2−D3ΩL+Ωse−j(δst+θs)2ΩA200ΩL+Ωsej(δst+θs)2−D4000ΩA20−D5](1)H(t) = \hbar\times \begin{bmatrix} 0 & \frac{\Omega_p}{2} & 0 & 0 & 0 \\ \frac{\Omega_p}{2} & -\Delta_p & \frac{\Omega_c}{2} & 0 & 0 \\ 0 & \frac{\Omega_c}{2} & -D_3 & \frac{\Omega_L+\Omega_s e^{-j(\delta_s t+\theta_s)}}{2} & \frac{\Omega_A}{2} \\ 0 & 0 & \frac{\Omega_L+\Omega_s e^{j(\delta_s t+\theta_s)}}{2} & -D_4 & 0 \\ 0 & 0 & \frac{\Omega_A}{2} & 0 & -D_5 \end{bmatrix} \tag*{(1)}

where ℏ\hbar denotes the reduced Planck constant. Here, θs=ϕs−ϕLO\theta_s = \phi_s - \phi_{\mathrm{LO}} is the phase shift between the MW signal (ϕs\phi_s) and LO (ϕLO\phi_{\mathrm{LO}}). D3D_3, D4D_4, and D5D_5 are given by

D3=Δp+Δc+ξA,(2)D_3 = \Delta_p + \Delta_c + \xi_A, \tag*{(2)}
D4=Δp+Δc−ΔL−ξA,(3)D_4 = \Delta_p + \Delta_c - \Delta_L - \xi_A, \tag*{(3)}

and

D5=Δp+Δc+ΔA,(4)D_5 = \Delta_p + \Delta_c + \Delta_A, \tag*{(4)}

where ξA=μ342μ352ΩA24Δ′\xi_A = \frac{\mu_{34}^2}{\mu_{35}^2}\frac{\Omega_A^2}{4\Delta'} is the AUX-MW-induced alternating current (AC) Stark shift1, and μi,j\mu_{i,j} denotes the dipole moment between level ∣i⟩\lvert i\rangle and ∣j⟩\lvert j\rangle. Δp=ωp−ω21\Delta_p = \omega_p - \omega_{21}, Δc=ωc−ω32\Delta_c = \omega_c - \omega_{32}, ΔL=ωL−ω34\Delta_L = \omega_L - \omega_{34}, and ΔA=ωA−ω53\Delta_A = \omega_A - \omega_{53} denote the detunings of the probe laser, coupling laser, LO MW, and AUX MW, respectively. Δ′=ωA−ω34=ΔA+ω53−ω34\Delta' = \omega_A - \omega_{34} = \Delta_A + \omega_{53} - \omega_{34} denotes the detuning of the AUX MW with respect to the ∣3⟩↔∣4⟩\lvert3\rangle\leftrightarrow\lvert4\rangle transition.

From (1), the Hamiltonian can be decomposed as

H(t)=H0+ΩsH+ej(δst+θs)+ΩsH−e−j(δst+θs),(5)H(t) = H_0 + \Omega_s H_+ e^{j(\delta_s t+\theta_s)} + \Omega_s H_- e^{-j(\delta_s t+\theta_s)}, \tag*{(5)}

where H0H_0, H+H_+ and H−H_- are expressed as

H0=ℏ[0Ωp2000Ωp2−ΔpΩc2000Ωc2−D3ΩL2ΩA200ΩL2−D4000ΩA20−D5],(6)H_0 = \hbar \begin{bmatrix} 0 & \frac{\Omega_p}{2} & 0 & 0 & 0 \\ \frac{\Omega_p}{2} & -\Delta_p & \frac{\Omega_c}{2} & 0 & 0 \\ 0 & \frac{\Omega_c}{2} & -D_3 & \frac{\Omega_L}{2} & \frac{\Omega_A}{2} \\ 0 & 0 & \frac{\Omega_L}{2} & -D_4 & 0 \\ 0 & 0 & \frac{\Omega_A}{2} & 0 & -D_5 \end{bmatrix}, \tag*{(6)}
H+=ℏ2∣4⟩⟨3∣,(7)H_+ = \frac{\hbar}{2}\lvert4\rangle\langle3\rvert, \tag*{(7)}

and

H−=ℏ2∣3⟩⟨4∣.(8)H_- = \frac{\hbar}{2}\lvert3\rangle\langle4\rvert. \tag*{(8)}

Therefore, the LO MW is included in the time-independent part H0H_0, while the received signal MW appears as a time-periodic perturbation at the intermediate angular frequency δs\delta_s.

Let ρ(t)∈C5×5\rho(t) \in\mathbb{C}^{5 \times5} denote the density matrix of the atomic system and ρij\rho_{ij} mean the (i,j)(i,j)-th element of ρ(t)\rho(t). The density matrix is governed by the Lindblad master equation [32]

dρdt=−jℏ[H(t),ρ]−12{Γ,ρ}+Λ,\frac{d\rho}{dt} = -\frac{j}{\hbar}[H(t),\rho] - \frac{1}{2}\{\Gamma,\rho\} + \Lambda,
Γ=diag⁡{γ,γ+γ2,γ+γr,γ+γr,γ+γr},\Gamma= \operatorname{diag}\{\gamma,\gamma+\gamma_2,\gamma+\gamma_r,\gamma+\gamma_r,\gamma+\gamma_r\},
Λ=diag⁡{γ+γ2ρ22+γrρ44,γrρ33,γrρ55,0,0}.(9)\Lambda= \operatorname{diag}\{\gamma+\gamma_2\rho_{22}+\gamma_r\rho_{44},\gamma_r\rho_{33},\gamma_r\rho_{55},0,0\}. \tag*{(9)}

where Γ\Gamma is the relaxation matrix and Λ\Lambda is the repopulation matrix. γ2\gamma_2 denotes the spontaneous population decay rate of state ∣2⟩\lvert2\rangle, γr\gamma_r is a phenomenological approximation for the three Rydberg population decay rates, and γ\gamma represents the effective dephasing rate, including the transit broadening, the residual two-photon Doppler dephasing, and the dipole–dipole broadening.

To obtain the response at the intermediate frequency δs\delta_s, we use the Floquet theory. Under the weak-signal condition, i.e., ∣Ωs∣≪∣ΩL∣|\Omega_s| \ll|\Omega_L|, the density matrix is approximated by2^{2}

ρ(t)≈ρ(0)+ρ(+1)ej(δst+θs)+ρ(−1)e−j(δst+θs),(10)\rho(t) \approx\rho^{(0)}+\rho^{(+1)}e^{j(\delta_s t+\theta_s)}+\rho^{(-1)}e^{-j(\delta_s t+\theta_s)}, \tag*{(10)}

where ρ(0)\rho^{(0)} is the zeroth-order density matrix induced by the probe laser, coupling laser, LO MW, and AUX MW, while ρ(+1)\rho^{(+1)} and ρ(−1)\rho^{(-1)} are the first-order sideband density matrices induced by the weak signal MW. Then, the power of the output probe beam is related to ρ21\rho_{21}, which is given by

Pout(ρ21)=Pinexp⁡{LcellkpDΩℑ[ρ21(t)]},(11)P_{\mathrm{out}}(\rho_{21})=P_{\mathrm{in}}\exp\left\{L_{\mathrm{cell}}k_pD_{\Omega}\Im\left[\rho_{21}(t)\right]\right\}, \tag*{(11)}

where PinP_{\mathrm{in}} means the power of the input probe beam and LcellL_{\mathrm{cell}} is the length of vapor cell. DΩ=2N0μ122ϵ0ℏΩpD_{\Omega}=\frac{2N_0\mu_{12}^{2}}{\epsilon_0\hbar\Omega_p} represents the constant term, N0N_0 is the atomic number density, kp=2π/λpk_p=2\pi/\lambda_p is the probe wavenumber, and μ12\mu_{12} is the effective dipole moment.

Wideband Reception Model

This section derives approximate closed-form expressions for the optical response using Floquet theory and then develops the corresponding wideband multicarrier reception model.

Output Probe Beam

As can be seen from (9), it is challenging to derive the exact expression of the output probe beam. To tackle this issue, we derive the closed-form expression of ρ21\rho_{21} under the following physically motivated assumptions. Particularly, we assume that the system operates in the weak-probe regime [32], i.e., ρ11≈1\rho_{11}\approx1, ρii≈0\rho_{ii}\approx0, i=2,3,4,5i=2,3,4,5. Based on these assumptions, the optical coherence can be expanded as

ρ21(t)≈ρ21(0)+ρ21(+)ej(δst+θs)+ρ21(−)e−j(δst+θs).(12)\rho_{21}(t)\approx\rho_{21}^{(0)}+\rho_{21}^{(+)}e^{j(\delta_s t+\theta_s)}+\rho_{21}^{(-)}e^{-j(\delta_s t+\theta_s)}. \tag*{(12)}

Then, the closed-form expression of the steady-state optical coherence is given by

ρ21(0)=ΩpΞ(0)2F(0),ρ21(±)=ΩsH±(δs),(13)\rho_{21}^{(0)}=\frac{\Omega_p\Xi(0)}{2F(0)},\qquad\rho_{21}^{(\pm)}=\Omega_s H_{\pm}(\delta_s), \tag*{(13)}

where

H+(δs)=ΩpΩL2ΩL32F(0)Z4(δs)F(δs),(14)H_{+}(\delta_s)=\frac{\Omega_p\Omega_L^2\Omega_L}{32F(0)Z_4(\delta_s)F(\delta_s)}, \tag*{(14)}
H−(δs)=ΩpΩL2ΩL32F(0)Z4(0)F(−δs).(15)H_{-}(\delta_s)=\frac{\Omega_p\Omega_L^2\Omega_L}{32F(0)Z_4(0)F(-\delta_s)}. \tag*{(15)}

Furthermore, Ξ(δs)\Xi(\delta_s) and F(δs)F(\delta_s) are given by

Ξ(δs)=Z3(δs)−ΩL24Z4(δs)−ΩA24Z5(δs),(16)\Xi(\delta_s)=Z_3(\delta_s)-\frac{\Omega_L^2}{4Z_4(\delta_s)}-\frac{\Omega_A^2}{4Z_5(\delta_s)}, \tag*{(16)}

and

F(δs)=Z2(δs)Ξ(δs)−Ωc24,(17)F(\delta_s)=Z_2(\delta_s)\Xi(\delta_s)-\frac{\Omega_c^2}{4}, \tag*{(17)}

where

Z2(δs)=Δp−δs+jη2,Zk(δs)=Dk−δs+jηr,k=3,4,5.(18)\begin{aligned} Z_2(\delta_s)&=\Delta_p-\delta_s+j\eta_2,\\ Z_k(\delta_s)&=D_k-\delta_s+j\eta_r,\qquad k=3,4,5. \tag*{(18)} \end{aligned}

In (18), η2=γ+γ22\eta_2=\gamma+\frac{\gamma_2}{2} and ηr=γ+γr2\eta_r=\gamma+\frac{\gamma_r}{2}. The detailed derivation is provided in Appendix A.

By using the first-order coherence approximation and substituting (12) into (11), we have

Pout(t)≈Pout(0)exp⁡{LcellkpDΩℑ{ρ21(+)ej(δst+θs)+ρ21(−)e−j(δst+θs)}},(19)P_{\mathrm{out}}(t)\approx P_{\mathrm{out}}^{(0)}\exp\left\{L_{\mathrm{cell}}k_pD_{\Omega}\Im\left\{\rho_{21}^{(+)}e^{j(\delta_s t+\theta_s)}+\rho_{21}^{(-)}e^{-j(\delta_s t+\theta_s)}\right\}\right\}, \tag*{(19)}

where Pout(0)P_{\mathrm{out}}^{(0)} is given by

Pout(0)=Pinexp⁡{LcellkpDΩℑ{ρ21(0)}}.(20)P_{\mathrm{out}}^{(0)}=P_{\mathrm{in}}\exp\left\{L_{\mathrm{cell}}k_pD_{\Omega}\Im\left\{\rho_{21}^{(0)}\right\}\right\}. \tag*{(20)}

Since ρ21(+)\rho_{21}^{(+)} and ρ21(−)\rho_{21}^{(-)} are first-order small quantities induced by the weak signal field, the exponential term can be linearized by using ex=1+x+O(x2)e^x=1+x+\mathcal{O}(x^2). Therefore, we have

Pout(t)≈Pout(0){1+LcellkpDΩΩsℑ{H+(δs)ej(δst+θs)+H−(δs)e−j(δst+θs)}}.(21)P_{\mathrm{out}}(t)\approx P_{\mathrm{out}}^{(0)}\left\{1+L_{\mathrm{cell}}k_pD_{\Omega}\Omega_s\Im\left\{H_{+}(\delta_s)e^{j(\delta_s t+\theta_s)}+H_{-}(\delta_s)e^{-j(\delta_s t+\theta_s)}\right\}\right\}. \tag*{(21)}

Meanwhile, the corresponding phase of the transmitted probe beam is approximated as

ϕp(t)≈ϕp(0)−LcellkpDΩΩs2ℜ{H+(δs)ej(δst+θs)+H−(δs)e−j(δst+θs)},(22)\phi_p(t)\approx\phi_p^{(0)}-\frac{L_{\mathrm{cell}}k_pD_{\Omega}\Omega_s}{2}\Re\left\{H_{+}(\delta_s)e^{j(\delta_s t+\theta_s)}+H_{-}(\delta_s)e^{-j(\delta_s t+\theta_s)}\right\}, \tag*{(22)}

where ϕp(0)=ϕp,in−LcellkpDΩ2ℜ{ρ21(0)}\phi_p^{(0)}=\phi_{p,\mathrm{in}}-\frac{L_{\mathrm{cell}}k_pD_{\Omega}}{2}\Re\left\{\rho_{21}^{(0)}\right\} and ϕp,in\phi_{p,\mathrm{in}} is the phase of the input probe beam.

Equivalent Model

To improve the optical readout sensitivity, balanced coherent optical detection (BCOD) is adopted [19]. The transmitted probe beam can be expressed as

xp(t)=2Pout(t)cos⁡[ωpt+ϕp(t)].(23)x_p(t)=\sqrt{2P_{\mathrm{out}}(t)}\cos\left[\omega_p t+\phi_p(t)\right]. \tag*{(23)}

A phase-coherent reference optical beam is introduced as

xr(t)=2Prcos⁡(ωpt+ϕr),(24)x_r(t)=\sqrt{2P_r}\cos\left(\omega_p t+\phi_r\right), \tag*{(24)}

where PrP_r and ϕr\phi_r denote the power and phase of the reference optical beam, respectively.

After combining the transmitted probe and the reference optical beam through a beam splitter and subtracting the photocurrents of the two photodetectors, the BCOD output voltage is given by

VB(t)=2GARLRpdPrPout(t)cos⁡[ϕr−ϕp(t)],(25)V_B(t)=2\sqrt{G_A R_L R_{\mathrm{pd}}\sqrt{P_rP_{\mathrm{out}}(t)}}\cos\left[\phi_r-\phi_p(t)\right], \tag*{(25)}

Following the electrical-gain convention in [19], GAG_A is the linear post-detection power gain. The quantities RpdR_{\mathrm{pd}} and RLR_L are the photodetector responsivity and load resistance, respectively. For simplicity, we assume that the reference beam is phase aligned with the steady-state transmitted probe, i.e., ϕr=ϕp(0)\phi_r=\phi_p^{(0)}. Consequently, cos⁡[ϕr−ϕp(t)]=1+O(Ωs2)\cos[\phi_r-\phi_p(t)]=1+\mathcal{O}(\Omega_s^2) can be approximated as 11, under the weak-signal condition, i.e., Ωs≪ΩL\Omega_s \ll\Omega_L. Then, substituting (21) and (22) into (25) and retaining only the first-order terms with respect to Ωs\Omega_s, we have

VB(t)≈VDC+VAC(t),(26)V_{\mathrm{B}}(t) \approx V_{\mathrm{DC}} + V_{\mathrm{AC}}(t), \tag*{(26)}

where

VDC=2GARLRpdPrPout(0),(27)V_{\mathrm{DC}} = 2\sqrt{G_{\mathrm{A}}R_{\mathrm{L}}R_{\mathrm{pd}}\sqrt{P_{\mathrm{r}}P_{\mathrm{out}}^{(0)}}}, \tag*{(27)}

and

VAC(t)=GARLRpdPrPout(0)LcellkpDΩΩs×ℑ{[H+(δs)−H−∗(δs)]ej(δst+θs)}.(28)V_{\mathrm{AC}}(t) = \sqrt{G_{\mathrm{A}}R_{\mathrm{L}}R_{\mathrm{pd}}\sqrt{P_{\mathrm{r}}P_{\mathrm{out}}^{(0)}}L_{\mathrm{cell}}k_{\mathrm{p}}D_{\Omega}\Omega_s \times\Im\left\{\left[H_{+}(\delta_s)-H_{-}^{*}(\delta_s)\right]e^{j(\delta_s t+\theta_s)}\right\}.} \tag*{(28)}

We next derive an idealized steady-state communication model from the output voltage. The symbol interval of duration is TsT_s, during which the wireless channel coefficient and transmitted symbol are assumed to remain constant. Then, the Rabi frequency Ωs=μ34ℏEs\Omega_s=\frac{\mu_{34}}{\hbar}E_s is determined by the amplitude of the received signal MW Es=60PtGtddis∣hs∣E_s=\frac{\sqrt{60P_tG_t}}{d_{\mathrm{dis}}}|h_s|, where PtP_t, GtG_t, and ddisd_{\mathrm{dis}} denote the transmit power, transmit antenna gain, and propagation distance, respectively. h∼CN(0,1)h\sim\mathcal{CN}(0,1) and s∈C1×1s\in\mathbb{C}^{1\times1} denote the wireless channel coefficient and transmitted information during the current symbol interval. Furthermore, the received signal phase and its phase relative to the LO MW are ϕs=arg⁡{hs}\phi_s=\arg\{h_s\} and θs=ϕs−ϕLO\theta_s=\phi_s-\phi_{\mathrm{LO}} respectively. Substituting these results into (28), we have

VAC(t)=GARLRpdPrPout(0)LcellkpDΩμ34ℏ60PtGtddis×∣hs∣ℑ{[H+(δs)−H−∗(δs)]ej(δst+θs)}.(29)V_{\mathrm{AC}}(t)=\sqrt{G_{\mathrm{A}}R_{\mathrm{L}}R_{\mathrm{pd}}\sqrt{P_{\mathrm{r}}P_{\mathrm{out}}^{(0)}}L_{\mathrm{cell}}k_{\mathrm{p}}D_{\Omega}\frac{\mu_{34}}{\hbar}\frac{\sqrt{60P_tG_t}}{d_{\mathrm{dis}}} \times|h_s|\Im\left\{\left[H_{+}(\delta_s)-H_{-}^{*}(\delta_s)\right]e^{j(\delta_s t+\theta_s)}\right\}.} \tag*{(29)}

Then, the imaginary part of [H+(δs)−H−∗(δs)]ej(δst+θs)\left[H_{+}(\delta_s)-H_{-}^{*}(\delta_s)\right]e^{j(\delta_s t+\theta_s)} can be rewritten as

ℑ{[H+(δs)−H−∗(δs)]ej(δst+θs)}=ℜ{H+(δs)−H−∗(δs)}sin⁡(δst+θs)+ℑ{H+(δs)−H−∗(δs)}cos⁡(δst+θs).(30)\Im\left\{\left[H_{+}(\delta_s)-H_{-}^{*}(\delta_s)\right]e^{j(\delta_s t+\theta_s)}\right\} =\Re\left\{H_{+}(\delta_s)-H_{-}^{*}(\delta_s)\right\}\sin(\delta_s t+\theta_s) +\Im\left\{H_{+}(\delta_s)-H_{-}^{*}(\delta_s)\right\}\cos(\delta_s t+\theta_s). \tag*{(30)}

We assume ideal coherent downconversion followed by low-pass filtering to reject the image at angular frequency 2∣δs∣2|\delta_s|. For the finite-interval projection below, a nonzero IF satisfying δsTs=2πℓ\delta_sT_s=2\pi\ell, ℓ∈Z∖{0}\ell\in\mathbb{Z}\setminus\{0\}, is selected, and thus the image term integrates to zero over the symbol interval. The recovered complex baseband symbol is given by

2Ts∫0TsVAC(t)sin⁡(δst) dt+j2Ts∫0TsVAC(t)cos⁡(δst) dt=gcPt[H+(δs)−H−∗(δs)]hse−jϕLO,(31)\frac{2}{T_s}\int_{0}^{T_s}V_{\mathrm{AC}}(t)\sin(\delta_s t)\,dt+j\frac{2}{T_s}\int_{0}^{T_s}V_{\mathrm{AC}}(t)\cos(\delta_s t)\,dt =g_c\sqrt{P_t}\left[H_{+}(\delta_s)-H_{-}^{*}(\delta_s)\right]h_se^{-j\phi_{\mathrm{LO}}}, \tag*{(31)}

where gc=GARLRpdPrPout(0)LcellkpDΩ60Gtddisμ34ℏg_c=\sqrt{G_{\mathrm{A}}}R_{\mathrm{L}}R_{\mathrm{pd}}\sqrt{P_{\mathrm{r}}P_{\mathrm{out}}^{(0)}}L_{\mathrm{cell}}k_{\mathrm{p}}D_{\Omega}\frac{\sqrt{60G_t}}{d_{\mathrm{dis}}}\frac{\mu_{34}}{\hbar} denotes the conversion gain. Therefore, the received symbol is

y=gcPt[H+(δs)−H−∗(δs)]e−jϕLOhs+wy=g_c\sqrt{P_t}\left[H_{+}(\delta_s)-H_{-}^{*}(\delta_s)\right]e^{-j\phi_{\mathrm{LO}}}h_s+w
≜Ptg(δs)hs+w(32)\triangleq\sqrt{P_t}g(\delta_s)h_s+w \tag*{(32)}

where g(δs)=gc[H+(δs)−H−∗(δs)]e−jϕLOg(\delta_s)=g_c\left[H_{+}(\delta_s)-H_{-}^{*}(\delta_s)\right]e^{-j\phi_{\mathrm{LO}}}. Following [19], we model the aggregate quantum projection noise, photon shot noise, and intrinsic thermal noise at the demodulator output as equivalent complex Gaussian noise, w∼CN(0,σ2)w\sim\mathcal{CN}(0,\sigma^2).

Multicarrier Extension

We next extend the single-carrier model to an idealized one-sided OFDM signal with NcN_c subcarriers and a useful symbol duration of TsT_s [33, 34]. Consistent with the preceding ideal-detection assumptions, cyclic-prefix overhead, atomic memory across symbol boundaries, and transient effects are neglected. Let n∈Nc≜{1,⋯ ,Nc}n\in\mathcal{N}_c\triangleq\{1,\cdots,N_c\} and δsn=ωsn−ωL\delta_s^n=\omega_s^n-\omega_L denote the subcarrier index and the angular-frequency offset between the nn-th signal subcarrier and the LO MW, respectively. Similar to the single-carrier case, we consider an arbitrary multicarrier symbol interval of duration TsT_s and assume that the wireless channel remains approximately constant within this interval. Consequently, the channel coefficient hnh_n and transmitted symbol sns_n are treated as constants over the considered symbol interval, and the symbol index is omitted for notational simplicity.

The phase shift between the received signal of the nn-th subcarrier and the LO MW is θn=ϕs,n−ϕLO\theta_n=\phi_{s,n}-\phi_{\mathrm{LO}}, where ϕs,n=arg⁡{hnsn}\phi_{s,n}=\arg\{h_ns_n\}. Then, the Rabi-frequency amplitude is written as

Ωs,n=μ34ℏ60Pt,nGtddis∣hnsn∣,(33)\Omega_{s,n}=\frac{\mu_{34}}{\hbar}\frac{\sqrt{60P_{t,n}G_t}}{d_{\mathrm{dis}}}|h_ns_n|, \tag*{(33)}

where Pt,nP_{t,n} denotes the average power allocated to subcarrier nn, with E∣sn∣2=1\mathbb{E}|s_n|^2=1 and ∑n=1NcPt,n=Pt\sum_{n=1}^{N_c}P_{t,n}=P_t. Here, hnh_n and sns_n denote the channel coefficient and transmitted symbol on the nn-th subcarrier, respectively. Accordingly, the signal contribution to the rotating-frame Hamiltonian is obtained by superposing the contributions from all subcarriers.

Based on the above discussion, the multicarrier Hamiltonian can be written as

H(t)=H0+∑n=1NcΩs,n[H+ej(δsnt+θn)+H−e−j(δsnt+θn)].(34)\mathbf{H}(t)=\mathbf{H}_0+\sum_{n=1}^{N_c}\Omega_{s,n}\left[\mathbf{H}_{+}e^{j(\delta_s^n t+\theta_n)} +\mathbf{H}_{-}e^{-j(\delta_s^n t+\theta_n)}\right]. \tag*{(34)}

We assume that the aggregate multicarrier microwave field is weak relative to the LO field. Under the first-order approximation, each subcarrier independently induces sideband coherences at ±δsn\pm\delta_s^n, while the zeroth-order coherence ρ21(0)\rho_{21}^{(0)} remains unchanged and higher-order intermodulation terms are neglected. Solving the Lindblad master equation under these approximations, we obtain

ρ21(t)≈ρ21(0)+∑n=1NcΩs,nH+(δsn)ej(δsnt+θn)+∑n=1NcΩs,nH−(δsn)e−j(δsnt+θn).(35)\begin{aligned} \rho_{21}(t)\approx\rho_{21}^{(0)}+\sum_{n=1}^{N_c}\Omega_{s,n}H_{+}(\delta_s^n)e^{j(\delta_s^n t+\theta_n)} \\ &+\sum_{n=1}^{N_c}\Omega_{s,n}H_{-}(\delta_s^n)e^{-j(\delta_s^n t+\theta_n)}. \tag*{(35)} \end{aligned}

Therefore, compared with the single-carrier case, the first-order atomic response is simply the superposition of the sideband responses generated by the NcN_c signal components. Substituting the first-order coherence in (35) into (11), we have

Pout(t)≈Pout(0)exp⁡{LcellkpDΩ∑n=1NcΩs,n×ℑ{[H+(δsn)−H−∗(δsn)]ej(δsnt+θn)}}.(36)P_{\mathrm{out}}(t) \approx P_{\mathrm{out}}^{(0)} \exp\left\{L_{\mathrm{cell}} k_p D_\Omega\sum_{n=1}^{N_c} \Omega_{s,n} \times\Im\left\{\left[H_+(\delta_s^n)-H_-^*(\delta_s^n)\right]e^{j(\delta_s^n t+\theta_n)}\right\}\right\}. \tag*{(36)}

Under the same first-order weak-signal approximation, the exponential term in (36) can be approximated as

Pout(t)≈Pout(0){1+LcellkpDΩ∑n=1NcΩs,n×ℑ{[H+(δsn)−H−∗(δsn)]ej(δsnt+θn)}}.(37)P_{\mathrm{out}}(t) \approx P_{\mathrm{out}}^{(0)}\left\{1+L_{\mathrm{cell}} k_p D_\Omega\sum_{n=1}^{N_c}\Omega_{s,n}\times\Im\left\{\left[H_+(\delta_s^n)-H_-^*(\delta_s^n)\right]e^{j(\delta_s^n t+\theta_n)}\right\}\right\}. \tag*{(37)}

After photodetection and removal of the DC component, the corresponding AC voltage is

VAC,Nc(t)=GARLRpdPrPout(0)LcellkpDΩ∑n=1NcΩs,n×ℑ{[H+(δsn)−H−∗(δsn)]ej(δsnt+θn)}.(38)V_{\mathrm{AC},N_c}(t)=\sqrt{G_A}R_L\mathcal{R}_{\mathrm{pd}}\sqrt{P_rP_{\mathrm{out}}^{(0)}}L_{\mathrm{cell}}k_pD_\Omega\sum_{n=1}^{N_c}\Omega_{s,n}\times\Im\left\{\left[H_+(\delta_s^n)-H_-^*(\delta_s^n)\right]e^{j(\delta_s^n t+\theta_n)}\right\}. \tag*{(38)}

For notational convenience, we define the frequency-dependent complex response of the RAQR as

g(δsn)=gc[H+(δsn)−H−∗(δsn)]e−jϕLO,(39)g(\delta_s^n)=g_c\left[H_+(\delta_s^n)-H_-^*(\delta_s^n)\right]e^{-j\phi_{\mathrm{LO}}}, \tag*{(39)}

Then, the multicarrier AC voltage can be rewritten as

VAC,Nc(t)=∑n=1Ncℑ{Pt,ng(δsn)hnsnejδsnt}.(40)V_{\mathrm{AC},N_c}(t)=\sum_{n=1}^{N_c}\Im\left\{\sqrt{P_{t,n}}g(\delta_s^n)h_ns_ne^{j\delta_s^n t}\right\}. \tag*{(40)}

(40) shows that the photodetector output is a real-valued multi-tone IF waveform, whose nn-th component has the complex envelope Pt,ng(δsn)hnsn\sqrt{P_{t,n}}g(\delta_s^n)h_ns_n. Compared with the single-carrier case, the RAQR therefore simultaneously maps the received multicarrier RF signal onto multiple IF components with subcarrier-dependent atomic amplitude and phase responses.

In the following, we describe the FFT-based digital demodulation of VAC,Nc(t)V_{\mathrm{AC},N_c}(t). First, we place the data subcarriers below the LO, namely ωsn=ωL−2πnTs\omega_s^n=\omega_L-\frac{2\pi n}{T_s}, and thus δsn=ωsn−ωL=−2πnTs\delta_s^n=\omega_s^n-\omega_L=-\frac{2\pi n}{T_s}, n∈Ncn\in\mathcal{N}_c. Each symbol interval is uniformly sampled at M>2NcM>2N_c points, corresponding to a sampling rate of Fs=M/TsF_s=M/T_s. The mm-th sample is given by

vAC[m]=VAC,Nc(mTsM)=∑n=1Ncℑ{Pt,ng(δsn)hnsnejδsnmTsM}.(41)v_{\mathrm{AC}}[m]=V_{\mathrm{AC},N_c}\left(\frac{mT_s}{M}\right) =\sum_{n=1}^{N_c}\Im\left\{\sqrt{P_{t,n}}g(\delta_s^n)h_ns_ne^{j\frac{\delta_s^n mT_s}{M}}\right\}. \tag*{(41)}

Exploiting discrete Fourier transform (DFT) orthogonality, the noisy observation on the nnth subcarrier is obtained through an MM-point FFT as

yn=2jM∑m=0M−1vAC[m]e−jδsnmTsM=Pt,ng(δsn)hnsn+w^n,(42)y_n=\frac{2j}{M}\sum_{m=0}^{M-1}v_{\mathrm{AC}}[m]e^{-j\frac{\delta_s^n mT_s}{M}} =\sqrt{P_{t,n}}g(\delta_s^n)h_ns_n+\hat{w}_n, \tag*{(42)}

where w^n∼CN(0,σn2)\hat{w}_n\sim\mathcal{CN}(0,\sigma_n^2) denotes the equivalent noise after FFT demodulation. Following [19], the receiver-noise model incorporates quantum projection noise, photon shot noise, and thermal noise.

Stacking the FFT outputs across all NcN_c subcarriers yields the vector model

y=G(δs)HcPt1/2s+w^,(43)\mathbf{y}=\mathbf{G}(\boldsymbol{\delta}_s)\mathbf{H}_c\mathbf{P}_t^{1/2}\mathbf{s}+\hat{\mathbf{w}}, \tag*{(43)}

where y=[y1,⋯ ,yNc]T\mathbf{y}=[y_1,\cdots,y_{N_c}]^{\mathrm{T}}, s=[s1,⋯ ,sNc]T\mathbf{s}=[s_1,\cdots,s_{N_c}]^{\mathrm{T}}, and w^=[w^1,⋯ ,w^Nc]T\hat{\mathbf{w}}=[\hat{w}_1,\cdots,\hat{w}_{N_c}]^{\mathrm{T}} denote the received-signal, transmitted-symbol, and noise vectors, respectively. The transmit-power allocation matrix is defined as Pt=diag⁡{Pt,1,⋯ ,Pt,Nc}\mathbf{P}_t=\operatorname{diag}\{P_{t,1},\cdots,P_{t,N_c}\}. Furthermore, G(δs)=diag⁡{g(δs1),⋯ ,g(δsNc)}\mathbf{G}(\boldsymbol{\delta}_s)=\operatorname{diag}\{g(\delta_s^1),\cdots,g(\delta_s^{N_c})\} and Hc=diag⁡{h1,⋯ ,hNc}\mathbf{H}_c=\operatorname{diag}\{h_1,\cdots,h_{N_c}\} collect the complex frequency responses and wireless channel coefficients across the NcN_c subcarriers, respectively.

Remark 1 (One-sided bandwidth): Although the RAQR exhibits responses at both positive and negative microwave-LO frequency offsets, the real-valued BCOD output maps the two sidebands onto the same demodulated frequency band. Therefore, the transmitted signals on both sides would overlap and create image interference. To avoid this ambiguity, data subcarriers are allocated to only one side of the LO. For an approximately symmetric response, the resulting usable bandwidth for independent data transmission is about half of the double-sided atomic-response bandwidth.

Remark 2 (Frequency-dependent atomic response): (43) shows that the RAQR first converts the received RF multicarrier signal into a real-valued multi-tone IF waveform, which is then digitized and decomposed into orthogonal subcarriers via a single FFT. However, the FFT only separates the orthogonal subcarriers and does not compensate for either the frequency-dependent RAQR response or the wireless propagation channel. In particular, the strongly frequency-dependent atomic response may cause substantial subcarrier-dependent amplitude and phase variations, motivating the RAQR-aware frequency-domain equalizer.

RAQR-Aware Equalization

Assuming perfect knowledge of the nonzero composite subcarrier gain dn=Pt,ng(δsn)hnd_n=\sqrt{P_{t,n}}g(\delta_s^n)h_n, the estimated symbol based on the RAQR-aware zero-forcing (ZF) equalizer is

s^ZF,n=yndn=sn+w^ndn.(44)\hat{s}_{\mathrm{ZF},n}=\frac{y_n}{d_n}=s_n+\frac{\hat{w}_n}{d_n}. \tag*{(44)}

Accordingly, the output SNR is given by

γZF,n=Pt,n∣g(δsn)∣2∣hn∣2σn2.(45)\gamma_{\mathrm{ZF},n}=\frac{P_{t,n}|g(\delta_s^n)|^2|h_n|^2}{\sigma_n^2}. \tag*{(45)}

Then, the achievable rate is expressed as

RZF=Δf∑n=1Nclog⁡2(1+γZF,n).(46)R_{\mathrm{ZF}}=\Delta f\sum_{n=1}^{N_c}\log_2(1+\gamma_{\mathrm{ZF},n}). \tag*{(46)}

Bandwidth and Conversion-Gain Analysis

This section characterizes the effects of the LO and AUX fields on the one-sided response and examines its tradeoff with bandwidth.

Response and Performance Metrics

To characterize the receiver bandwidth, we normalize the complex response H(δs)=H+(δs)−H−∗(δs)H(\delta_s)=H_{+}(\delta_s)-H_{-}^{*}(\delta_s) by its zero-detuning value H(0)≠0H(0)\ne0. At each fixed LO/AUX operating point, the normalized response and the corresponding LO-referenced bandwidth are defined as

R(δs)=∣g(δs)∣2∣g(0)∣2≜∣H(δs)∣2∣H(0)∣2,(47)R(\delta_s)=\frac{\lvert g(\delta_s)\rvert^2}{\lvert g(0)\rvert^2}\triangleq\frac{\lvert H(\delta_s)\rvert^2}{\lvert H(0)\rvert^2}, \tag*{(47)}
W+≜12πmin⁡{x>0:R(−x)=1/2}.(48)W_{+}\triangleq\frac{1}{2\pi}\min\left\{x>0:R(-x)=1/2\right\}. \tag*{(48)}

Here, ∣H(0)∣\lvert H(0)\rvert characterizes the center atomic-response amplitude, whereas the actual conversion coefficient satisfies ∣g(0)∣=∣gc∣∣H(0)∣\lvert g(0)\rvert=\lvert g_c\rvert\lvert H(0)\rvert. The readout prefactor gcg_c is independent of δs\delta_s but varies with the LO and AUX driving. Note that this definition imposes a lower threshold relative to the center response rather than a bound on in-band ripple. For nonmonotonic responses with off-center peaks, the bandwidth does not guarantee a ripple of at most 3 dB and generally differs from the peak-referenced 3-dB bandwidth.

Owing to the analytical intractability of R(δs)R(\delta_s), analyzing the normalized response is nontrivial. To tackle this issue, we assume that the probe, coupling, and LO fields are perfectly resonant, namely Δp=Δc=ΔL=0\Delta_p=\Delta_c=\Delta_L=0. Substituting these conditions into (2)–(4), we have D3=ξAD_3=\xi_A, D4=−ξAD_4=-\xi_A, and D5=ΔAD_5=\Delta_A. Then, Zk(δs)Z_k(\delta_s) is simplified to Zk(δs)=ζk−δsZ_k(\delta_s)=\zeta_k-\delta_s for k∈{2,3,4,5}k\in\{2,3,4,5\}, where

ζ2=jη2,ζ3=ξA+jηr,ζ4=−ξA+jηr,ζ5=ΔA+jηr.(49)\begin{aligned} \zeta_2&=j\eta_2,\qquad\zeta_3=\xi_A+j\eta_r,\\ \zeta_4&=-\xi_A+j\eta_r,\qquad\zeta_5=\Delta_A+j\eta_r. \tag*{(49)} \end{aligned}

The imaginary parts of these complex detunings are the decay rates of the coherences, whereas the real parts of ζ3\zeta_3 and ζ4\zeta_4 are the AC Stark shifts that the AUX field induces on ∣3⟩\lvert3\rangle and ∣4⟩\lvert4\rangle. Then, these complex detunings and the field couplings are collected into the coherence matrix, which is given by

M=[ζ2Ωc/200Ωc/2ζ3ΩL/2ΩA/20ΩL/2ζ400ΩA/20ζ5].(50)\mathbf{M}= \begin{bmatrix} \zeta_2 & \Omega_c/2 & 0 & 0\\ \Omega_c/2 & \zeta_3 & \Omega_L/2 & \Omega_A/2\\ 0 & \Omega_L/2 & \zeta_4 & 0\\ 0 & \Omega_A/2 & 0 & \zeta_5 \end{bmatrix}. \tag*{(50)}

Expanding Q(δs)≜det⁡(M−δsI)Q(\delta_s)\triangleq\det(\mathbf{M}-\delta_s\mathbf{I}) along the row of ∣3⟩\lvert3\rangle, we have

Q(δs)=F(δs)Z4(δs)Z5(δs).(51)Q(\delta_s)=F(\delta_s)Z_4(\delta_s)Z_5(\delta_s). \tag*{(51)}

Substituting F(δs)=Q(δs)Z4(δs)Z5(δs)F(\delta_s)=\frac{Q(\delta_s)}{Z_4(\delta_s)Z_5(\delta_s)} into (14) and (15), the response at perfect resonance is expressed as

Hr(δs)=C0ζ4ζ5(ζ5−δs)Q(0)Q(δs)−C0∗ζ4∗ζ5∗(ζ5∗+δs)Q∗(0)Q∗(−δs),(52)H_r(\delta_s)=\frac{C_0\zeta_4\zeta_5(\zeta_5-\delta_s)}{Q(0)Q(\delta_s)}-\frac{C_0^*\zeta_4^*\zeta_5^*(\zeta_5^*+\delta_s)}{Q^*(0)Q^*(-\delta_s)}, \tag*{(52)}

where C0=ΩpΩc2ΩL32C_0=\frac{\Omega_p\Omega_c^2\Omega_L}{32}. Although (52) is explicit, the roles of LO and AUX driving are not apparent. To clarify these roles, we approximate the resonance locations by exploiting two separated frequency scales. The complex detunings, comprising decay rates and AUX-induced shifts, govern the leading-order linewidths and frequency shifts, whereas the coupling and LO fields set the dominant splitting through the dressing scale

Ω‾≜ΩL2+Ωc2.\overline{\Omega}\triangleq\sqrt{\Omega_L^2+\Omega_c^2}.

Effects of a Far-Detuned AUX Field

We first simplify the response by eliminating the coherence associated with ∣5⟩\lvert5\rangle, and obtain a frequency-dependent 3×33\times3 representation. Since ∣5⟩\lvert5\rangle couples only to ∣3⟩\lvert3\rangle, the Schur complement of its diagonal entry in M−δsI4\mathbf{M}-\delta_s\mathbf{I}_4 yields

Q(δs)=(ζ5−δs)det⁡(M^(δs)−δsI3).(53)Q(\delta_s)=(\zeta_5-\delta_s)\det\left(\widehat{\mathbf{M}}(\delta_s)-\delta_s\mathbf{I}_3\right). \tag*{(53)}

For ζ5≠δs\zeta_5\ne\delta_s, M^(δs)\widehat{\mathbf{M}}(\delta_s) is the upper-left 3×33\times3 block of M\mathbf{M} with ζ3\zeta_3 replaced by [ζ3−ΩA24(ζ5−δs)]\left[\zeta_3-\frac{\Omega_A^2}{4(\zeta_5-\delta_s)}\right]. The factors ζ5(ζ5−δs)\zeta_5(\zeta_5-\delta_s) and ζ5∗(ζ5∗+δs)\zeta_5^*(\zeta_5^*+\delta_s) in the numerators are cancelled by factorization, and thus the AUX influence is retained through the frequency-dependent correction to the complex detuning of ∣3⟩\lvert3\rangle.

To approximate the AUX-induced correction as frequency-independent, we assume ∣ΔA∣≫max⁡{ΩA,∣δs∣,ηr}\lvert\Delta_A\rvert\gg\max\{\Omega_A,\lvert\delta_s\rvert,\eta_r\} throughout the band of interest. Then, with ζ5−δs≈ΔA\zeta_5-\delta_s\approx\Delta_A, the shift of ∣3⟩\lvert3\rangle reduces to the static dispersive shift −ΩA24ΔA-\frac{\Omega_A^2}{4\Delta_A}. Accordingly, M^(δs)\widehat{\mathbf{M}}(\delta_s) is approximated by

M^(δs)≈M~=[ζ2Ωc/20Ωc/2ζ~3ΩL/20ΩL/2ζ4],(54)\widehat{\mathbf{M}}(\delta_s)\approx\widetilde{\mathbf{M}}= \begin{bmatrix} \zeta_2 & \Omega_c/2 & 0\\ \Omega_c/2 & \widetilde{\zeta}_3 & \Omega_L/2\\ 0 & \Omega_L/2 & \zeta_4 \end{bmatrix}, \tag*{(54)}

where ζ~3=D~3+jηr\widetilde{\zeta}_3=\widetilde{D}_3+j\eta_r and

D~3=ξA−ΩA24ΔA=ΩA24(μ342μ352Δ′−1ΔA).(55)\widetilde{D}_3=\xi_A-\frac{\Omega_A^2}{4\Delta_A}=\frac{\Omega_A^2}{4}\left(\frac{\mu_{34}^2}{\mu_{35}^2\Delta'}-\frac{1}{\Delta_A}\right). \tag*{(55)}

Therefore, we have Q(δs)≈(ζ5−δs)P(δs)Q(\delta_s)\approx(\zeta_5-\delta_s)\mathcal{P}(\delta_s), where P(δs)\mathcal{P}(\delta_s) is

P(δs)=det⁡(M~−δsI)=(ζ2−δs)(ζ~3−δs)(ζ4−δs)−(ζ2−δs)ΩL24−(ζ4−δs)Ωc24.(56)\begin{aligned} \mathcal{P}(\delta_s)&=\det(\widetilde{\mathbf{M}}-\delta_s\mathbf{I})\\ &=(\zeta_2-\delta_s)(\widetilde{\zeta}_3-\delta_s)(\zeta_4-\delta_s)\\ &\quad-(\zeta_2-\delta_s)\frac{\Omega_L^2}{4}-(\zeta_4-\delta_s)\frac{\Omega_c^2}{4}. \tag*{(56)} \end{aligned}

Substituting this result into (52), we have

Hr(δs)≈C0ζ4P(0)P(δs)−C0(ζ4∗+δs)P∗(0)P∗(−δs).(57)H_r(\delta_s)\approx\frac{C_0\zeta_4}{\mathcal{P}(0)\mathcal{P}(\delta_s)}-\frac{C_0(\zeta_4^*+\delta_s)}{\mathcal{P}^*(0)\mathcal{P}^*(-\delta_s)}. \tag*{(57)}

Remark 3 (Effects of AUX MW): The far-detuned AUX field influences the receiver primarily through dispersive dressing rather than resonant population transfer. The admixture of ∣5⟩\lvert5\rangle into ∣3⟩\lvert3\rangle scales as ΩA24ΔA2\frac{\Omega_A^2}{4\Delta_A^2} and remains small under the far-detuning assumption. Its dominant effect is to introduce static

Atomic Driving and Relaxation
ParameterValueUnit
Probe Rabi frequency Ωp/(2π)\Omega_p/(2\pi)0.85MHz
Coupling Rabi frequency Ωc/(2π)\Omega_c/(2\pi)15MHz
LO Rabi frequency ΩL/(2π)\Omega_L/(2\pi)7.5MHz
AUX Rabi frequency ΩA/(2π)\Omega_A/(2\pi)150MHz
Probe detuning Δp/(2π)\Delta_p/(2\pi)0MHz
Coupling detuning Δc/(2π)\Delta_c/(2\pi)0MHz
LO detuning ΔL/(2π)\Delta_L/(2\pi)0MHz
AUX detuning ΔA/(2π)\Delta_A/(2\pi)1697MHz
Off-resonant detuning Δ′/(2π)\Delta'/(2\pi)3214MHz
Effective dephasing rate γ/(2π)\gamma/(2\pi)0.352MHz
Decay rate γ2/(2π)\gamma_2/(2\pi)6.07MHz
Decay rate γ3,γ4,γ5/(2π)\gamma_3,\gamma_4,\gamma_5/(2\pi)2.2, 2.2, 2.2kHz
Optical and Cell Parameters
ParameterValueUnit
Probe dipole ∣μ12∣|\mu_{12}|2.989ea0ea_0
Coupling dipole ∣μ23∣|\mu_{23}|0.01527ea0ea_0
LO/signal dipole ∣μ34∣|\mu_{34}|2117.49ea0ea_0
AUX dipole ∣μ35∣|\mu_{35}|2176.08ea0ea_0
Probe wavelength λp\lambda_p780.241nm
Cell length LcellL_{\mathrm{cell}}6.5cm
Atomic density N0N_05.89×10145.89 \times10^{14}m−3\mathrm{m}^{-3}
Probe power PinP_{\mathrm{in}}252nW
Coupling power PcP_c3W
Beam diameter wp=wcw_p=w_c0.7mm
Reference optical power PrP_r30mW
PD responsivity Rpd\mathcal{R}_{\mathrm{pd}}0.5494A/W
Readout and Communication
ParameterValueUnit
LO carrier frequency fLOf_{\mathrm{LO}}≈16.03\approx16.03GHz
Electrical power gain GAG_A30dB
Load resistance RLR_L1Ω\Omega
Number of subcarriers NcN_c1024–
Subcarrier spacing Δf\Delta f10kHz
Allocated bandwidth NcΔfN_c\Delta f10.24MHz
Total transmit power PtP_t23dBm
Transmit antenna gain GtG_t0dBi
Propagation distance ddisd_{\mathrm{dis}}1500m
Noise temperature TpdT_{\mathrm{pd}}100K
RF receiver noise figure7dB
Effective RF receive gain3.951dBi

level shifts. Specifically, ∣3⟩|3\rangle experiences the effective shift Δ~3\widetilde{\Delta}_3, which combines the AC Stark shift ξA\xi_A from the off-resonant ∣3⟩↔∣4⟩|3\rangle\leftrightarrow|4\rangle coupling and the dispersive shift −ΩA24ΔA-\frac{\Omega_A^2}{4\Delta_A} induced by ∣5⟩|5\rangle, while ∣4⟩|4\rangle is shifted by −ξA-\xi_A. The five-level receiver can therefore be interpreted as an effective four-level system with tunable Rydberg-level detunings. As shown below, these shifts play distinct roles. The shift Δ~3\widetilde{\Delta}_3 mainly controls the position of the Autler–Townes doublet, whereas ξA\xi_A primarily modifies the conversion gain.

Autler–Townes Doublet

According to (56), P(δs)\mathcal{P}(\delta_s) is the characteristic polynomial of M\mathbf{M}. Therefore, the resonances of the two terms in (57) are associated with its eigenvalues and their mirror images about the LO frequency, respectively. Physically, the coupling and LO fields form three dressed states from ∣2⟩|2\rangle, ∣3⟩|3\rangle, and ∣4⟩|4\rangle. In the lossless, zero-detuning limit, their eigenvalues are 0 and ±Ω‾/2\pm\overline{\Omega}/2. The dark state contains no ∣3⟩|3\rangle component because the two coupling pathways interfere destructively, whereas the bright states form an Autler–Townes doublet with splitting Ω‾\overline{\Omega}. Decay rates broaden the dressed-state resonances, whereas AUX-induced detunings shift their frequencies. When these diagonal perturbations are small relative to the dressed-state splitting, first-order perturbation theory yields eigenvalue corrections weighted by the corresponding unperturbed dressed-state populations. Accordingly, P(δs)\mathcal{P}(\delta_s) is approximated by

P(δs)≈(λ0−δs)[(δs−β−jα)2−Ω‾24](58)\mathcal{P}(\delta_s) \approx(\lambda_0-\delta_s)\left[(\delta_s-\beta-\mathrm{j}\alpha)^2-\frac{\overline{\Omega}^2}{4}\right] \tag*{(58)}

where λ0=ξAΩL2+ξAΩc2Ω‾2\lambda_0=\frac{\xi_A\Omega_L^2+\xi_A\Omega_c^2}{\overline{\Omega}^2} denotes the approximate dark-mode eigenvalue, while β=ξAΩc22Ω‾2−ΩA24ΔA\beta=\frac{\xi_A\Omega_c^2}{2\overline{\Omega}^2}-\frac{\Omega_A^2}{4\Delta_A} and α=ηr+(η2−ηr)Ωc22Ω‾2\alpha=\eta_r+\frac{(\eta_2-\eta_r)\Omega_c^2}{2\overline{\Omega}^2} represent the frequency shift and decay rate of the bright modes, respectively.

Remark 4 (Effects of LO and AUX): Physically, increasing ΩL\Omega_L enlarges the doublet splitting Ω‾\overline{\Omega} and reduces its linewidth by decreasing the contribution of the short-lived state ∣2⟩|2\rangle. In contrast, AUX driving shifts the bright-mode doublet through β\beta and perturbs the dark resonance through ξA\xi_A. With AUX driving, the dark resonance shifts to ℜ{λ0}≈−ξAΩc2Ω‾2<0\Re\{\lambda_0\}\approx-\frac{\xi_A\Omega_c^2}{\overline{\Omega}^2}<0 for ξA>0\xi_A>0, contributing to an asymmetric atomic response about the LO. Under the considered operating conditions, this asymmetry favors negative signal–LO offsets, motivating the allocation of data subcarriers below the LO frequency.

Impacts on Gain and Bandwidth

The dark resonance primarily determines the center atomic gain. By setting δs=0\delta_s=0 in (57), we have

Hr(0)=2jC0ξ{ξ4D2(0)}.(59)H_r(0)=2\mathrm{j}C_0\xi\left\{\frac{\xi_4}{\mathcal{D}^2(0)}\right\}. \tag*{(59)}

Since P(0)=−Ω‾2λ04+ζ2ζ3ζ4\mathcal{P}(0)=-\frac{\overline{\Omega}^2\lambda_0}{4}+\zeta_2\zeta_3\zeta_4, the EIT condition ∣ζ~3∣≪Ωc24η2|\widetilde{\zeta}_3|\ll\frac{\Omega_c^2}{4\eta_2} allows us to approximate P(0)≈−Ω‾2λ04\mathcal{P}(0)\approx-\frac{\overline{\Omega}^2\lambda_0}{4}. Substituting this equation into (59), ∣Hr(0)∣|H_r(0)| is approximated by

∣Hr(0)∣≈ΩpΩc2ΩL[ηrS2+ξAΩc2(2S−ηrΩc2)](S2+ξA2Ωc4)2,(60)|H_r(0)|\approx\frac{\Omega_p\Omega_c^2\Omega_L\left[\eta_rS^2+\xi_A\Omega_c^2(2S-\eta_r\Omega_c^2)\right]}{(S^2+\xi_A^2\Omega_c^4)^2}, \tag*{(60)}

where S≜η2ΩL2+ηrΩc2S\triangleq\eta_2\Omega_L^2+\eta_r\Omega_c^2. Under AUX driving, the center atomic gain in (60) depends jointly on the LO Rabi frequency ΩL\Omega_L and the AUX-induced shift ξA\xi_A. Increasing ΩL\Omega_L enhances RF-induced modulation but also increases SS, which may suppress the center response. Meanwhile, AUX driving modifies both the numerator and denominator of (60) through ξA\xi_A. Consequently, AUX driving can enhance the center gain when its positive contribution outweighs the detuning-induced loss. Specifically, for a fixed LO operating point, the approximate gain exceeds its AUX-free value when

S2(2S−3ηrΩc2)>ηrξA2Ωc6.(61)S^2(2S-3\eta_r\Omega_c^2)>\eta_r\xi_A^2\Omega_c^6. \tag*{(61)}

The bright states primarily determine the side peaks. Near δs≈−(Ω‾2∓β)\delta_s\approx-\left(\frac{\overline{\Omega}}{2}\mp\beta\right), the second term of (57) dominates when ∣ζ4∣,∣λ0∣≪Ω‾2|\zeta_4|,|\lambda_0|\ll\frac{\overline{\Omega}}{2}. The corresponding peak magnitude is approximated by ∣Hr∣pk≈4C0Ωˉ3α∣λ0∣|H_r|_{\mathrm{pk}} \approx\frac{4C_0}{\bar{\Omega}^{3}\alpha|\lambda_0|}, and the peak-to-center ratio is given by

∣Hr∣pk∣Hr(0)∣≈Ωˉ8α∣λ0∣∣ℑ{ζ4/λ02}∣(62)\frac{|H_r|_{\mathrm{pk}}}{|H_r(0)|} \approx\frac{\bar{\Omega}}{8\alpha|\lambda_0|\left|\Im\left\{\zeta_4/\lambda_0^2\right\}\right|} \tag*{(62)}

Without AUX driving, this ratio reduces to Ωˉℑ{λ0}8αηr\frac{\bar{\Omega}\Im\{\lambda_0\}}{8\alpha\eta_r} and increases with ΩL\Omega_L for η2>ηr\eta_2>\eta_r. In contrast, AUX driving increases ∣λ0∣|\lambda_0| and reduces the side peak by the factor (1+ξA2Ωc2/S2)−1/2(1+\xi_A^2\Omega_c^2/S^2)^{-1/2} with a fixed LO.

Remark 5 (Effects of LO and AUX driving on the gain-bandwidth tradeoff): Increasing ΩL\Omega_L enlarges the dressed-state splitting Ωˉ\bar{\Omega} and can broaden the continuous LO-referenced bandwidth by shifting the bright-mode resonances outward. However, the center atomic gain does not increase monotonically and eventually decreases in the LO-dominated regime. In contrast, AUX driving primarily adjusts the dressed-state detunings and can enhance the center gain under (61). Nevertheless, under the considered operating conditions, the increased center response and suppressed outer-band response can narrow the normalized LO-referenced bandwidth. Therefore, LO and AUX driving exhibit distinct effects on the gain-bandwidth tradeoff to balance sensitivity and bandwidth.

One-Sided LO-referenced Bandwidth and Gain–Bandwidth Tradeoff

To characterize the gain-bandwidth tradeoff analytically, we first consider the AUX-free receiver, for which (57) is simplified as

HrAF(δs)=C0(2jηr−δs)P(0)P(δs).(63)H_r^{\mathrm{AF}}(\delta_s)=\frac{C_0(2j\eta_r-\delta_s)}{\mathcal{P}(0)\mathcal{P}(\delta_s)}. \tag*{(63)}

The corresponding center atomic gain is ∣HrAF(0)∣=2C0ηr∣P(0)∣2|H_r^{\mathrm{AF}}(0)|=\frac{2C_0\eta_r}{|\mathcal{P}(0)|^2}. Based on this response, we establish the following gain-bandwidth inequality.

Proposition 1 (Gain-bandwidth inequality): For the AUX-free receiver, let B=Ωˉ24+2η2ηr+ηr2\mathcal{B}=\frac{\bar{\Omega}^2}{4}+2\eta_2\eta_r+\eta_r^2. The one-sided LO-referenced bandwidth satisfies

(2πW+)2≤B+C0ηr∣HrAF(0)∣(1+4ηr2B).(64)(2\pi W_+)^2\leq\mathcal{B}+\sqrt{\frac{C_0}{\eta_r|H_r^{\mathrm{AF}}(0)|}\left(1+\frac{4\eta_r^2}{\mathcal{B}}\right)}. \tag*{(64)}

Proof: For the AUX-free response, direct expansion gives ∣P(δs)∣2=δs2(δs2−B)2+[(η2+2ηr)δs2−∣P(0)∣2]2|\mathcal{P}(\delta_s)|^2=\delta_s^2(\delta_s^2-\mathcal{B})^2+\left[(\eta_2+2\eta_r)\delta_s^2-|\mathcal{P}(0)|^2\right]^2. If (2πW+)2≤B(2\pi W_+)^2\leq\mathcal{B}, the claimed bound holds directly. Otherwise, for δs2>B\delta_s^2>\mathcal{B}, discarding the nonnegative second term yields R(δs)≤∣P(0)∣2(δs2−B)2(1δs2+14ηr2)R(\delta_s)\leq\frac{|\mathcal{P}(0)|^2}{(\delta_s^2-\mathcal{B})^2}\left(\frac{1}{\delta_s^2}+\frac{1}{4\eta_r^2}\right). Evaluating this inequality at the half-power boundary δs=2πW+\delta_s=2\pi W_+, where R(2πW+)=1/2R(2\pi W_+)=1/2, and using ∣HrAF(0)∣=2C0ηr/∣P(0)∣2|H_r^{\mathrm{AF}}(0)|=2C_0\eta_r/|\mathcal{P}(0)|^2 establishes (64).

Proposition 1 constrains the achievable bandwidth relative to the center atomic-response amplitude. For fixed B\mathcal{B} and C0C_0, increasing the center gain tightens the bandwidth bound. However, LO driving changes both quantities, and thus the actual tradeoff depends on the operating regime. As a result, we examine the strong-LO limit.

Corollary 1 (Strong-LO gain–bandwidth tradeoff): For the AUX-free receiver with η2>2ηr\eta_2>\sqrt{2}\eta_r, as ΩL→∞\Omega_L\to\infty with all other parameters fixed, the one-sided bandwidth satisfies

∣HrAF(0)∣2(2πW+)6→Ωp2Ωc41282η2ηr(1+2ηrη2)3.(65)|H_r^{\mathrm{AF}}(0)|^2(2\pi W_+)^6 \to\frac{\Omega_p^2\Omega_c^4}{128\sqrt{2}\eta_2\eta_r}\left(1+\frac{\sqrt{2}\eta_r}{\eta_2}\right)^3. \tag*{(65)}

Proof: In the strong-LO limit, ∣P(0)∣∼η2ΩL24|\mathcal{P}(0)|\sim\frac{\eta_2\Omega_L^2}{4}, giving ∣HrAF(0)∣∼ΩpΩc2ηrη22ΩL3|H_r^{\mathrm{AF}}(0)|\sim\frac{\Omega_p\Omega_c^2\eta_r}{\eta_2^2\Omega_L^3}. Meanwhile, the LO-referenced bandwidth satisfies 2πW+∼ΩL21+η22ηr2\pi W_+\sim\frac{\Omega_L}{2}\sqrt{1+\frac{\eta_2}{\sqrt{2}\eta_r}}. Combining their leading-order expressions yields (65).

Corollary 1 reveals that the center atomic-response power scales as W+−6W_+^{-6} in the AUX-free strong-LO regime. Consequently, doubling the one-sided bandwidth incurs an asymptotic power loss of approximately 18.1 dB.

With AUX driving, the dispersive shifts modify both the center response and the bright-mode resonances. Under the preceding far-detuned and dominant-response approximations, we consider operating points where the outer half-power crossing is also the first half-power crossing below the LO. Then, the LO-referenced bandwidth approximately satisfies

2πW+≈Ωˉ24−α2+K2−Ωˉ2α2+β,(66)2\pi W_+\approx\sqrt{\frac{\bar{\Omega}^2}{4}-\alpha^2+\sqrt{\mathcal{K}^2-\bar{\Omega}^2\alpha^2}+\beta}, \tag*{(66)}

where K=2∣C0∣∣P(0)∣\mathcal{K}=\frac{\sqrt{2}|C_0|}{|\mathcal{P}(0)|}. This relation reveals that AUX driving can enhance the center gain by adjusting the dark-state resonance, while the induced frequency shift β\beta modifies the band edge. Under the considered detuning conditions, improved the center gain may therefore come at the expense of a narrower continuous LO-referenced bandwidth, highlighting the gain-bandwidth tradeoff.

Simulation Results

This section evaluates the analytical model, the frequency response, and multicarrier equalization under the considered operating conditions.

Parameter Settings

We adopt the five-level 87Rb{}^{87}\mathrm{Rb} scheme in [32], with ∣1⟩=∣5S1/2,F=2⟩|1\rangle=|5S_{1/2},F=2\rangle, ∣2⟩=∣5P3/2,F′=3⟩|2\rangle=|5P_{3/2},F'=3\rangle, ∣3⟩=∣5D5/2,mJ=|3\rangle=|5D_{5/2},m_J= 5/2⟩5/2\rangle, ∣4⟩=∣52P3/2,mJ=3/2⟩|4\rangle= |52P_{3/2},m_J = 3/2\rangle, and ∣5⟩=∣50F7/2,mJ=7/2⟩|5\rangle= |50F_{7/2},m_J = 7/2\rangle. Unlike the thermal-vapor configuration, we consider a laser-cooled atomic ensemble at Ta=100T_a = 100 µK, where residual Doppler broadening is assumed negligible, allowing

the stationary-atom approximation without Doppler averaging. Unless otherwise stated, the parameters are listed in tbl:1. Furthermore, the phase of LO is set to ϕLO=0\phi_{\mathrm{LO}} = 0.

Closed-Form Expression Validation

We first validate the closed-form expressions derived under the weak-probe approximation. Figure 2 compares the real and imaginary parts of the derived steady-state response with numerical results obtained from the five-level Lindblad master equation for different probe Rabi frequencies. For the considered parameter setting, particularly Ωc/(2π)=15\Omega_c/(2\pi) = 15 MHz, the agreement in Figure 2 supports the weak-probe approximation for Ωp/(2π)<0.9\Omega_p/(2\pi) < 0.9 MHz. As the probe Rabi frequency increases, the discrepancy becomes more pronounced because population redistribution and saturation weaken the assumptions ρ11≈1\rho_{11} \approx1 and ρii≈0\rho_{ii} \approx0 for i=2,3,4,5i = 2, 3, 4, 5.

Curves of $\rho_{21}^{(0)}$ under various probe beams

Figure 2. ρ21(0)\rho_{21}^{(0)} under various probe beams.

We further validate the first-order Floquet components ρ21(+)\rho_{21}^{(+)} and ρ21(−)\rho_{21}^{(-)} within the weak-probe and weak-signal regimes. Figure 3 compares their real and imaginary parts with numerical results obtained from the five-level Lindblad master equation over different signal–LO detunings. We observe that the closed-form and numerical results remain in close agreement over the considered detuning range, demonstrating that the derived expressions accurately capture the frequency-dependent responses of both first-order Floquet components. Together with the steady-state validation, this agreement supports the accuracy of the closed-form expressions in characterizing the wideband atomic response.

Real and imaginary parts of $\rho_{21}^{(+)}$ and $\rho_{21}^{(-)}$ under different frequency offsets between the LO and the signal

Figure 3. ρ21(+)\rho_{21}^{(+)} and ρ21(−)\rho_{21}^{(-)} under different frequency offsets between the LO and the signal.

Atomic Response

Figure 4 illustrates the magnitude and phase responses across different signal-LO detunings. These frequency-dependent variations introduce subcarrier-dependent distortions even under a frequency-flat wireless channel, supporting Remark 2 and motivating subcarrier-dependent equalization. It can be seen from the figure that the one-sided LO-referenced bandwidth reaches approximately 11 MHz. Moreover, the reduced model in (57) closely matches the full response under sufficiently far-detuned AUX driving. Furthermore, Figure 5 reveals the distinct roles of AUX-induced level shifts. The shift of ∣3⟩\lvert3\rangle primarily displaces the bright-state doublet, whereas the shift of ∣4⟩\lvert4\rangle modifies the dark-state resonance and can enhance the center conversion gain, consistent with Remark 3.

Magnitude and phase response of RAQR under various detunings between the LO and user’s signal

Figure 4. Magnitude and phase response of RAQR under various detunings between the LO and user’s signal.

Effects of AUX-induced level shifts on the atomic response

Figure 5. Effects of AUX-induced level shifts on the atomic response. The individual-shift curves retain only one shift contribution to isolate its effect.

Gain–Bandwidth Tradeoff

Figure 6 illustrates the effects of LO and AUX driving on the conversion gain and one-sided LO-referenced bandwidth. Without AUX driving, increasing ΩL\Omega_{\mathrm{L}} shifts the bright-state resonances outward and narrows their linewidths by reducing the contribution of the short-lived state ∣2⟩\lvert2\rangle. Meanwhile, the increased ∣2⟩\lvert2\rangle contribution to the dark state broadens the central resonance and reduces the center gain. Consequently, W+W_{+} increases from 12.6 to 15.7 MHz at the cost of approximately 13.5 dB in center gain. In contrast, far-detuned AUX driving modifies the center and outer-band responses through dispersive level shifts. Under the considered operating conditions, the center response increases more strongly than the outer-band response in relative terms, thereby reducing the normalized response R(δs)=∣H(δs)∣2/∣H(0)∣2R(\delta_{\mathrm{s}})=\lvert H(\delta_{\mathrm{s}})\rvert^{2}/\lvert H(0)\rvert^{2} near the band edge. Consequently, the first half-power crossing shifts toward the LO, revealing that enhanced center conversion gain comes at the expense of a narrower LO-referenced bandwidth.

Effects of AUX and LO on response

Figure 6. Effects of AUX and LO on response.

comes at the expense of a narrower LO-referenced bandwidth. Together, these results support Remarks 4 and 5, highlighting the distinct roles of LO and AUX driving in shaping the gain-bandwidth tradeoff.

Figure 7 illustrates the LO-referenced bandwidth W+W_{+} versus the LO and AUX Rabi frequencies, with color indicating the center conversion gain 20log⁡10∣g(0)∣20\log_{10}\lvert g(0)\rvert. Increasing ΩL\Omega_{\mathrm{L}} broadens the bandwidth at the expense of center gain, whereas increasing ΩA\Omega_{\mathrm{A}} produces the opposite trend. The numerical bandwidth agrees with the analytical expression in (66), while the AUX-free results satisfy the upper bound established in Proposition 1. Moreover, the AUX-free operating points A and B agree well with the gain-bandwidth scaling predicted by Corollary 1. These results confirm the analyzed tradeoff and provide guidance for LO/AUX parameter selection.

Tradeoff between the center gain and bandwidth

Figure 7. Tradeoff between the center gain and bandwidth.

Wideband Multicarrier Receiver

Figure 8(a) reveals subcarrier-dependent amplitude and phase distortions caused by the frequency-selective atomic response, even under a frequency-flat wireless channel. Figure 8(b) further illustrates the impact of multipath fading, with joint ZF equalization restoring the transmitted symbols in the noiseless case. With the presence of receiver noise, Figure 8(c) shows that frequency-flat atomic calibration leads to rate saturation under mismatched decoding, whereas RAQR-aware equalization compensates for the frequency-dependent atomic response. As observed, at a transmit power of 23 dBm, the RAQR achieves a data rate 2.57 times that of the conventional RF benchmark, demonstrating the importance of RAQR-aware equalization and the potential of RAQRs for wideband multicarrier reception.

Constellations of input signal, RAQR output with equalization, and achievable-rate performance

Figure 8. Constellations of input signal, RAQR output with equalization, and achievable-rate performance.

Conclusions

This paper investigated continuous wideband OFDM reception using a five-level RAQR with a single microwave LO. The analysis revealed that the frequency-selective atomic response introduces subcarrier-dependent amplitude and phase distortions, highlighting the importance of RAQR-aware ZF equalization. Furthermore, LO and AUX driving exhibited distinct effects on the gain-bandwidth tradeoff. Under the considered operating conditions, stronger LO driving broadened the bandwidth at the expense of center response, whereas appropriate AUX driving enhanced the center response while narrowing the contiguous passband. In the AUX-free strong-LO regime, doubling the bandwidth incurred an approximately 18-dB reduction in center-response power. Simulation results supported these findings and demonstrated a contiguous one-sided LO-referenced bandwidth exceeding 11 MHz. These insights provide guidance for balancing bandwidth and conversion gain, highlighting the potential of RAQRs as wideband receiving front ends for future wireless communications.

Appendix A: Proof of the Weak-Probe Closed-Form Optical Coherence

Substituting the Hamiltonian in (1) into the master equation (9), we obtain the evolution equations for the coherences ρk1\rho_{k1}, k=2,3,4,5k=2,3,4,5. Defining φ=δst+θs\varphi=\delta_s t+\theta_s, these equations are given by

ρ˙21=−η2ρ21−j[Ωp2(ρ11−ρ22)−Δpρ21+Ωc2ρ31],ρ˙31=−ηrρ31−j[Ωc2ρ21−D3ρ31+ΩL+Ωse−jφ2ρ41+ΩA2ρ51−Ωp2ρ32],ρ˙41=−ηrρ41−j[ΩL+Ωsejφ2ρ31−D4ρ41−Ωp2ρ42],ρ˙51=−ηrρ51−j[ΩA2ρ31−D5ρ51−Ωp2ρ52].(67)\begin{aligned} \dot{\rho}_{21}&=-\eta_2\rho_{21}-\mathrm{j}\left[\frac{\Omega_p}{2}(\rho_{11}-\rho_{22})-\Delta_p\rho_{21}+\frac{\Omega_c}{2}\rho_{31}\right],\\ \dot{\rho}_{31}&=-\eta_r\rho_{31}-\mathrm{j}\left[\frac{\Omega_c}{2}\rho_{21}-D_3\rho_{31}+\frac{\Omega_L+\Omega_s e^{-\mathrm{j}\varphi}}{2}\rho_{41}+\frac{\Omega_A}{2}\rho_{51}-\frac{\Omega_p}{2}\rho_{32}\right],\\ \dot{\rho}_{41}&=-\eta_r\rho_{41}-\mathrm{j}\left[\frac{\Omega_L+\Omega_s e^{\mathrm{j}\varphi}}{2}\rho_{31}-D_4\rho_{41}-\frac{\Omega_p}{2}\rho_{42}\right],\\ \dot{\rho}_{51}&=-\eta_r\rho_{51}-\mathrm{j}\left[\frac{\Omega_A}{2}\rho_{31}-D_5\rho_{51}-\frac{\Omega_p}{2}\rho_{52}\right]. \tag*{(67)} \end{aligned}

These equations are obtained without invoking the weak-probe approximation. Since the repopulation matrix is diagonal, it does not contribute to the off-diagonal coherence dynamics, while the anticommutator term determines the coherence decay rates.

Under the weak-probe approximation, the atomic population remains predominantly in the ground state, yielding ρ11≈1\rho_{11}\approx1 and ρkk≈0\rho_{kk}\approx0, k=2,3,4,5k=2,3,4,5. Meanwhile, coherences between excited states are neglected, i.e., ρk2≈0\rho_{k2}\approx0, k=3,4,5k=3,4,5. Consequently, ρ11−ρ22≈1\rho_{11}-\rho_{22}\approx1, and (67) reduces to a closed set of linear equations for ρ21\rho_{21}, ρ31\rho_{31}, ρ41\rho_{41}, and ρ51\rho_{51}, while retaining the coupling, LO, and AUX fields without assuming weak driving.

Then, with the weak-signal, i.e., ∣Ωs∣≪∣ΩL∣|\Omega_s|\ll|\Omega_L|, the coherences are expanded as

ρk1(t)≈ρk1(0)+ρk1(+)ejφ+ρk1(−)e−jφ,(68)\rho_{k1}(t)\approx\rho_{k1}^{(0)}+\rho_{k1}^{(+)}e^{\mathrm{j}\varphi}+\rho_{k1}^{(-)}e^{-\mathrm{j}\varphi}, \tag*{(68)}

where the terms of higher order O(Ωs2)O(\Omega_s^2) are neglected. Substituting the Floquet expansions into (67) and retaining terms up to first order in Ωs\Omega_s yields three linear systems with the same coefficient structure. Therefore, these systems can be

expressed in a unified matrix form as

A(νq)x(q)=b(q),q∈{0,+,−},(69)A(\nu_q)\mathbf{x}^{(q)}=\mathbf{b}^{(q)},\qquad q\in\{0,+,-\}, \tag*{(69)}

where ν0=0\nu_0=0, ν+=δs\nu_+=\delta_s, and ν−=−δs\nu_-=-\delta_s. The coherence vector is defined as

x(q)=[ρ21(q),ρ31(q),ρ41(q),ρ51(q)]T.(70)\mathbf{x}^{(q)}=\left[\rho_{21}^{(q)},\rho_{31}^{(q)},\rho_{41}^{(q)},\rho_{51}^{(q)}\right]^{\mathrm{T}}. \tag*{(70)}

The coefficient matrix is given by

A(ν)=[Z2(ν)−Ωc/200−Ωc/2Z3(ν)−ΩL/2−ΩA/20−ΩL/2Z4(ν)00−ΩA/20Z5(ν)],(71)A(\nu)= \begin{bmatrix} Z_2(\nu)&-\Omega_c/2&0&0\\ -\Omega_c/2&Z_3(\nu)&-\Omega_L/2&-\Omega_A/2\\ 0&-\Omega_L/2&Z_4(\nu)&0\\ 0&-\Omega_A/2&0&Z_5(\nu) \end{bmatrix}, \tag*{(71)}

where Z2(ν)=Δp−ν+jη2Z_2(\nu)=\Delta_p-\nu+\mathrm{j}\eta_2 and Zk(ν)=Dk−ν+jηrZ_k(\nu)=D_k-\nu+\mathrm{j}\eta_r, k=3,4,5k=3,4,5. The corresponding source vectors are

b(0)=[Ωp/2,0,0,0]T,\mathbf{b}^{(0)}=[\Omega_p/2,0,0,0]^{\mathrm{T}},
b(+)=[0,0,Ωsρ31(0)/2,0]T,\mathbf{b}^{(+)}=[0,0,\Omega_s\rho_{31}^{(0)}/2,0]^{\mathrm{T}},
b(−)=[0,Ωsρ41(0)/2,0,0]T.(72)\mathbf{b}^{(-)}=[0,\Omega_s\rho_{41}^{(0)}/2,0,0]^{\mathrm{T}}. \tag*{(72)}

The signal phase θs\theta_s is already incorporated into the Floquet harmonics.

Since the three Floquet components share the same matrix structure, their solutions can be obtained through a common elimination procedure. For a fixed qq, let xk=ρk1(q)x_k=\rho_{k1}^{(q)}, k=2,3,4,5k=2,3,4,5, and write b(q)=[b2,b3,b4,b5]T\mathbf{b}^{(q)}=[b_2,b_3,b_4,b_5]^{\mathrm{T}}. The subscripts follow the atomic-state indices. In the following elimination, the superscript qq is omitted and all response functions are evaluated at νq\nu_q. Specifically, eliminating the third and fourth entries of x(q)\mathbf{x}^{(q)}, we have

x2=1F[Ξb2+Ωc2(b3+ΩLb42Z4+ΩAb52Z5)],(73)x_2=\frac{1}{F}\left[\Xi b_2+\frac{\Omega_c}{2}\left(b_3+\frac{\Omega_L b_4}{2Z_4}+\frac{\Omega_A b_5}{2Z_5}\right)\right], \tag*{(73)}

where

Ξ(ν)=Z3(ν)−ΩL24Z4(ν)−ΩA24Z5(ν).(74)\Xi(\nu)=Z_3(\nu)-\frac{\Omega_L^2}{4Z_4(\nu)}-\frac{\Omega_A^2}{4Z_5(\nu)}. \tag*{(74)}

and

F(ν)=Z2(ν)Ξ(ν)−Ωc24.(75)F(\nu)=Z_2(\nu)\Xi(\nu)-\frac{\Omega_c^2}{4}. \tag*{(75)}

Substituting b(0)\mathbf{b}^{(0)} into (73), we obtain

ρ21(0)=ΩpΞ(0)2F(0),ρ31(0)=ΩpΩc4F(0),ρ41(0)=ΩpΩcΩL8Z4(0)F(0).(76)\rho_{21}^{(0)}=\frac{\Omega_p\Xi(0)}{2F(0)},\quad\rho_{31}^{(0)}=\frac{\Omega_p\Omega_c}{4F(0)},\quad\rho_{41}^{(0)}=\frac{\Omega_p\Omega_c\Omega_L}{8Z_4(0)F(0)}. \tag*{(76)}

Similarly, substituting b(+)\mathbf{b}^{(+)} and b(−)\mathbf{b}^{(-)} into (73) and using (76), we have

ρ21(+)=ΩsΩpΩc2ΩL32F(0)Z4(δs)F(δs),\rho_{21}^{(+)}=\frac{\Omega_s\Omega_p\Omega_c^2\Omega_L}{32F(0)Z_4(\delta_s)F(\delta_s)},
ρ21(−)=ΩsΩpΩc2ΩL32F(0)Z4(0)F(−δs).(77)\rho_{21}^{(-)}=\frac{\Omega_s\Omega_p\Omega_c^2\Omega_L}{32F(0)Z_4(0)F(-\delta_s)}. \tag*{(77)}

Therefore, we complete the proof.

References

References

  1. [1]C.-X. Wang, X. You, X. Gao, X. Zhu, Z. Li, C. Zhang, H. Wang, Y. Huang, Y. Chen, H. Haas et al., “On the road to 6G: Visions, requirements, key technologies, and testbeds,” IEEE Commun. Surv. Tutor., vol. 25, no. 2, pp. 905–974, 2023.arxiv.org/abs/2302.14536
  2. [2]Q. Peng, Q. Luo, D. Xia, Z. Zhang, J. Wu, K. Wang, C. Pan, M. Elkashlan, P. Xiao, D. W. K. Ng, T. Q. Duong, G. K. Karagiannidis, and J. Wang, “Beyond the RF paradigm: Rydberg atomic receivers for next-generation IoT,” 2026, arXiv:2606.01263. [Online]. Available: https://arxiv.org/abs/2606.01263
  3. [3]H. Lu, Y. Zeng, C. You, Y. Han, J. Zhang, Z. Wang, Z. Dong, S. Jin, C.-X. Wang, T. Jiang, X. You, and R. Zhang, “A tutorial on near-field XL-MIMO communications toward 6G,” IEEE Commun. Surv. Tutor., vol. 26, no. 4, pp. 2213–2257, 2024.DOI
  4. [4]H. Tataria, M. Shafi, A. F. Molisch, M. Dohler, H. Sjöland, and F. Tufvesson, “6G wireless systems: Vision, requirements, challenges, insights, and opportunities,” Proc. IEEE, vol. 109, no. 7, pp. 1166–1199, 2021.
  5. [5]F. Lin, P.-I. Mak, and R. P. Martins, “Wideband receivers: Design challenges, tradeoffs and state-of-the-art,” IEEE Circuits Syst. Mag., vol. 15, no. 1, pp. 12–24, 2015.DOI
  6. [6]P. K. Sharma and N. Nallam, “Breaking the performance tradeoffs in N-path mixer-first receivers using a second-order baseband noise-canceling TIA,” IEEE J. Solid-State Circuits, vol. 55, no. 11, pp. 3009–3023, 2020.DOI
  7. [7]T. Gong, A. Chandra, C. Yuen, Y. L. Guan, R. Dumke, C. M. S. See, M. Debbah, and L. Hanzo, “Rydberg atomic quantum receivers for classical wireless communication and sensing,” IEEE Wireless Commun., vol. 32, no. 5, pp. 90–100, 2025.DOI
  8. [8]J. A. Sedlacek, A. Schwettmann, H. Kübler, R. Löw, T. Pfau, and J. P. Shaffer, “Microwave electrometry with Rydberg atoms in a vapour cell using bright atomic resonances,” Nat. Phys., vol. 8, no. 11, pp. 819–824, 2012.DOI
  9. [9]A. Mohapatra, T. Jackson, and C. Adams, “Coherent optical detection of highly excited rydberg states using electromagnetically induced transparency,” Phys. Rev. Lett., vol. 98, no. 11, p. 113003, 2007.pubmed.ncbi.nlm.nih.gov/17501049
  10. [10]E. Saglamyurek, T. Hrushevskyj, A. Rastogi, K. Heshami, and L. J. LeBlanc, “Coherent storage and manipulation of broadband photons via dynamically controlled autler–townes splitting,” Nat. Photonics, vol. 12, no. 12, pp. 774–782, 2018.DOI
  11. [11]M. Jing, Y. Hu, J. Ma, H. Zhang, L. Zhang, L. Xiao, and S. Jia, “Atomic superheterodyne receiver based on microwave-dressed Rydberg spectroscopy,” Nat. Phys., vol. 16, no. 9, pp. 911–915, 2020.
  12. [12]D. H. Meyer, K. C. Cox, F. K. Fatemi, and P. D. Kunz, “Digital communication with rydberg atoms and amplitude-modulated microwave fields,” Appl. Phys. Lett., vol. 112, no. 21, 2018.DOI
  13. [13]D. A. Anderson, R. E. Sapiro, and G. Raithel, “An atomic receiver for am and fm radio communication,” IEEE Trans. Antennas Propag., vol. 69, no. 5, pp. 2455–2462, 2020.DOI
  14. [14]C. L. Holloway, M. T. Simons, J. A. Gordon, and D. Novotny, “Detecting and receiving phase-modulated signals with a Rydberg atom-based receiver,” IEEE Antennas Wirel. Propag. Lett., vol. 18, no. 9, pp. 1853–1857, 2019.DOI
  15. [15]J. Nowosielski, M. Jastrzębski, P. Halavach, K. Łukanowski, M. Jarzyna, M. Mazelanik, W. Wasilewski, and M. Parniak, “Warm Rydberg atom-based quadrature amplitude-modulated receiver,” Opt. Express, vol. 32, no. 17, pp. 30 027–30 039, 2024.DOI
  16. [16]Y. Cai, S. Shi, Y. Zhou, Y. Li, J. Yu, W. Li, and L. Li, “High-sensitivity Rydberg-atom-based phase-modulation receiver for frequency-division-multiplexing communication,” Phys. Rev. Appl., vol. 19, no. 4, p. 044079, 2023.DOI
  17. [17]S. Borówka, M. Mazelanik, W. Wasilewski, and M. Parniak, “Optically-biased Rydberg microwave receiver enabled by hybrid nonlinear interferometry,” Nat. Commun., vol. 16, no. 1, p. 8975, 2025.DOI
  18. [18]J.-D. Nan, J.-R. Chen, B. Liu, Q.-F. Wang, Y. Ma, Y.-M. Yin, T.-Y. Han, G.-C. Guo, H. Tian, L.-H. Zhang, B. Du, B.-B. Wei, D.-S. Ding, and B.-S. Shi, “Ultra-broadband anti-jamming communication via a Rydberg atomic receiver,” Nat. Commun., vol. 17, p. 9643, 2026.
  19. [19]T. Gong, J. Sun, C. Yuen, G. Hu, Y. Zhao, Y. Guan, C. M. S. See, M. Debbah, and L. Hanzo, “Rydberg atomic quantum receivers for classical wireless communications and sensing: Their models and performance,” IEEE Trans. Commun., vol. 74, pp. 7759–7778, 2026.arxiv.org/abs/2412.05554
  20. [20]Y. Chen, X. Guo, C. Yuen, Y. L. Guan, C. M. S. See, M. Debbah, and L. Hanzo, “Harnessing Rydberg atomic receivers: From quantum physics to wireless communications,” IEEE Trans. Wireless Commun., vol. 25, pp. 19 971–19 990, 2026.arxiv.org/abs/2501.11842
  21. [21]Q. Peng, Q. Luo, Z. Chu, N. Ye, H. Ren, C. Pan, L. Xiao, and P. Xiao, “From active to battery-free: Rydberg atomic quantum receivers for self-sustained SWIPT-MIMO networks,” IEEE J. Sel. Areas Commun., vol. 44, pp. 4861–4875, 2026.arxiv.org/abs/2510.15784
  22. [22]Q. Peng, T. Gong, Z. Song, Q. Luo, Z. Lin, P. Xiao, and C. Yuen, “Enhanced ground–satellite direct access via onboard Rydberg atomic quantum receivers,” IEEE Wireless Commun., vol. 33, no. 3, pp. 23–30, 2026.arxiv.org/abs/2510.17290
  23. [23]N. Schlossberger, N. Prajapati, A. B. Artusio-Glimpse, S. Berweger, and C. L. Holloway, “Fundamental linewidth limit of electromagnetically induced transparency in a thermal Rydberg ladder,” Phys. Rev. Res., vol. 8, no. 3, p. L032046, 2026.DOI
  24. [24]S. M. Bohaichuk, D. Booth, K. Nickerson, H. Tai, and J. P. Shaffer, “Origins of Rydberg-atom electrometer transient response and its impact on radio-frequency pulse sensing,” Appl. Phys. Lett., vol. 18, no. 3, p. 034030, 2022.
  25. [25]J. Hu, Y. Jiao, Y. He, H. Zhang, L. Zhang, J. Zhao, and S. Jia, “Improvement of response bandwidth and sensitivity of rydberg receiver using multi-channel excitations,” EPJ Quantum Technol., vol. 10, no. 1, p. 51, 2023.DOI
  26. [26]S. Berweger, N. Prajapati, A. B. Artusio-Glimpse, A. P. Rotunno, R. Brown, C. L. Holloway, M. T. Sims, E. Imhof, S. R. Jefferts, B. N. Kayim et al., “Rydberg-state engineering: Investigations of tuning schemes for continuous frequency sensing,” Phys. Rev. Appl., vol. 19, no. 4, p. 044049, 2023.DOI
  27. [27]D. H. Meyer, J. C. Hill, P. D. Kunz, and K. C. Cox, “Simultaneous multiband demodulation using a Rydberg atomic sensor,” Phys. Rev. Appl., vol. 19, no. 1, p. 014025, 2023.DOI
  28. [28]M. Cui, Q. Zeng, M. Chen, Z. Wang, T. Mao, D. Zheng, and K. Huang, “Rydberg atomic receivers for multi-band communications and sensing,” IEEE Trans. Wireless Commun., vol. 25, pp. 13 384–13 400, 2026.arxiv.org/abs/2505.24168
  29. [29]H. Wang, T. Gong, E. Björnsen, and C. Yuen, “Multi-carrier Rydberg atomic quantum receivers with enhanced bandwidth feature for communication and sensing,” IEEE J. Sel. Areas Commun., vol. 44, pp. 5635–5650, 2026.arxiv.org/abs/2510.10473
  30. [30]B. Yang, Y. Yan, X. Li, L. Xiao, X. Li, L. Chen, J. Deng, and H. Cheng, “Highly sensitive microwave electrometry with enhanced instantaneous bandwidth,” Phys. Rev. Appl., vol. 21, no. 3, p. L031003, 2024.DOI
  31. [31]Y. Chen, C. Yuen, and C. M. S. See, “Wideband quantum transduction for Rydberg atomic receivers using six-wave mixing,” IEEE J. Sel. Areas Commun., vol. 44, pp. 5472–5488, 2026.
  32. [32]Y. Yan, X. Li, J. Wan, X. Xia, H. Zhao, B. Yu, J. Deng, H. Cheng, and L. Q. Chen, “Broadband Rydberg atomic microwave sensing with 44.6 MHz instantaneous bandwidth,” 2026. [Online]. Available: https://arxiv.org/abs/2606.25555
  33. [33]H. Zhu and J. Wang, “Chunk-based resource allocation in OFDMA systems-part I: chunk allocation,” IEEE Trans. Commun., vol. 57, no. 9, pp. 2734–2744, 2009.DOI
  34. [34]H. Zhu and J. Wang, “Chunk-based resource allocation in OFDMA systems—part II: Joint chunk, power and bit allocation,” IEEE Trans. Commun., vol. 60, no. 2, pp. 499–509, 2011.DOI

Paper details

vlnc:W_h4dm2xg8
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Engineering

Not recorded for this paper

View statement
Looking for related papers…
Contents