WorksPhysics and Astronomy
Topological insights into dense frictional suspension rheology: Third order loops drive discontinuous shear thickening
Abstract
Dense suspensions exhibit significant viscosity changes under external deformation, a phenomenon known as shear thickening. Recent studies have identified a stress-induced transition from lubricated, unconstrained interactions to frictional contacts, which play a crucial role in shear thickening. This work investigates the rheological behavior and contact network evolution during continuous and discontinuous shear thickening (CST and DST) in two-dimensional simulations. We find that at low stress, during weak thickening, the frictional contact network is composed of quasilinear chains along the compression axis. With increasing stress, the contact network becomes more isotropic, and forms loop-like structures. We show that third-order loops within the frictional contact network are key to this behavior. Our findings revealed a strong correlation between the number of edges in the third-order loops and the viscosity of the suspension. Notably, this relationship remains independent of the packing fraction, applied stress, and interparticle friction, highlighting the fundamental role of the mesoscale network topology in governing macroscopic rheology.
Introduction
Suspensions of small particles in a viscous liquid, a prototypical class of disordered amorphous materials, often exhibit enhanced resistance to flow (i.e., increased viscosity) under large deformation, a phenomenon known as shear thickening[1, 2, 3]. When the particle concentration, or packing fraction , approaches but remains below the jamming limit , the shear thickening behavior becomes abrupt, occurring over a narrow range of shear rates. This phenomenon is referred to as “discontinuous shear thickening” (DST)[2, 4, 5, 6, 7, 8, 9]. Extensive experimental studies have demonstrated that DST occurs under a wide range of conditions, including the variations in particle size[10, 11], stabilization mechanisms[11], and interfacial chemistry[12, 13, 14]. This generality suggests a unifying physical mechanism underlying the DST across diverse systems. At packing fractions , the suspension transitions into a solid-like shear-jammed (SJ) state under large deformation[15, 16]. This solid-like SJ state, formed under shear, is distinct from the unyielded viscoelastic soft solids typically studied in the context of colloidal gels[17, 18, 19, 20]. Unlike colloidal gels, which can sustain a load without continuous deformation, SJ solids rely on a dynamic, shear-induced contact network to support stress[2, 21, 22, 23]. The SJ state is fragile: the load is maintained only when the material is steadily sheared—any change in the direction or magnitude of loading results in temporary material failure. However, over time, steady shearing in the new direction can re-establish the contact network, forming a shear-jammed solid aligned with the new flow direction[22, 23].
Recent studies suggest that the breakdown of lubrication films, leading to the formation of frictional contacts between particles as the applied stress exceeds the onset stress , is the key mechanism driving the shear thickening behavior[4, 5]. This phenomenon represents a stress-activated transition from an unconstrained, lubricated “frictionless” state to a constrained state[8, 9, 24, 25]. These constraints, which originate from frictional contacts[5, 7, 8, 26, 27, 28] or a combination of hydrodynamic forces and surface asperities[29], significantly hinder the relative motion between particle pairs. Constraint-based mean-field models have been particularly successful in capturing the steady-state, strain-averaged flow behavior of dense suspensions and effectively describing data from both experiments and simulations[6, 7, 11, 30, 31]. These models predict a relationship between stress-induced frictional shear thickening and shear jamming, suggesting that strong shear thickening, or discontinuous shear thickening (DST), serves as a precursor to shear jamming[7, 15].
Although insightful, the aforementioned mean-field approaches do not account for the topological and geometrical characteristics of the mesoscale force and contact networks. These networks play a critical role in resisting external deformation, leading to enhanced viscosity and normal stresses. Recent studies have investigated the relationship between the underlying force and contact network structure and the rheology of both shear-thickening suspensions[32, 33, 34, 35, 36, 37, 38, 39, 40] and colloidal gels[19, 41]. Based on the observation in prior studies[5] showing the changes in pair-correlation functions in real space, showing minor changes across the DST transitions; Thomas et al.[33, 42] suggested that the network space (orthogonal to the particle space) plays a central role in understanding the statistical physics of frictional suspensions. Sedes et al. recently employed -core analysis to examine the particle clusters within a percolated contact network[34]. In addition, Nabizadeh et al.[39] applied community detection methods to reveal distinct interactions between clusters at packing fractions where suspensions transition from continuous shear thickening (CST) to discontinuous shear thickening (DST). Network science tools were initially applied to particulate systems to understand shear banding, jamming-unjamming, and related phenomena in dry granular materials, as reviewed by Papadopoulos et al.[43].
Previous studies on dry granular materials have highlighted a connection between the onset of rigidity, mechanical equilibrium, and characteristics of the contact network, particularly the presence of loops[44, 45]. This concept gained prominence through the observation of odd circuits in granular systems, referred to as R-loops[46], which are used to explain the origin of rigidity in granular packings[47]. These contact loops are known to contribute to the stability of granular materials[47, 48] and have provided valuable insights into the transition from fluid- to solid-like behavior[44], as well as the stress response[45] in granular packings. It is important to note that the term “cycle” ass also been used to describe such circuits[49, 50]. In this study, we adopt the term “loop” to topologically characterize the force network and, thus, maintain consistency with the existing literature[44, 45, 49].
In this study, we applied the loop-based network approach to a new context. Rather than analyzing the structure of loops in a static configuration, we examine the loop structure within a dynamically evolving network of frictional contacts in a dense suspension subjected to simple shear flow. This study aims to extract mesoscale features from the dynamical frictional contact network and correlate these features with viscosity, which depends on the packing fraction , applied stress , and particle friction . We demonstrate that the number of third-order loops, the smallest minimally rigid structures (in Laman’s theorem[51]), correlate strongly with pronounced shear thickening behavior. Specifically, we show that the viscosity increases with the number of third-order loop edges and appears to diverge as the number of these loops reaches a critical threshold. Moreover, this correlation is largely insensitive to particle friction, making third-order loop edges a valuable order parameter for identifying transitions in z material state.
Methodology
Our strategy for relating rheology with the mesoscale characterization proceeds in three parts: first, the physical data of particle position and interactions are mapped to a set of nodes and edges relevant to network science; second, we analyze the topological features of this network as the system is sheared; and third, we extract relevant features and study how our parameter space affects them. Finally, we correlate the flow behavior (viscosity) with the topological features of the frictional network.
Simulating dense suspensions
Although real-world dense suspensions are three-dimensional, related prior works have shown the flow behavior for 2D and 3D to be similar if the packing fraction is appropriately scaled[35, 39]. Given that loops are two-dimensional planar concepts, we performed two-dimensional simulations (a monolayer of spheres) in this study. The simulation scheme used here is, in principle, similar to that in the prior work by Mari et al.[5, 52] with the only difference being that we simulate a two-dimensional monolayer of spheres. In this study, a series of stress-controlled simulations are performed to analyze the frictional contact network in suspension close to but below the frictional jamming point . Our simulation scheme (LF-DEM) includes hydrodynamics interactions and repulsive contact forces that incorporate static friction. Hydrodynamic interactions include the one-body Stokes drag and two-body lubrication forces (LF). The contacts between two particles are modeled using the discrete element method (DEM) from dry granular materials[2, 5, 8, 28]. Ignoring the full hydrodynamics is strategic here with twofold aims: (i) We base ourselves on prior works by Singh et al.[8, 9] where a quantitative comparison has been reported considering lubrication interactions only; and (ii) including the full long-ranged hydrodynamic interactions makes the computation intractable[2, 53]. Shear is implemented using Lees-Edwards boundary condition under fixed shear stress with constant volume. To avoid crystallization, we simulate a particle mixture with a size ratio of 1.4 mixed in an equal volume.
Owing to the Stokes flow, that is, the inertialess limit, the particles obey the overdamped equation of motion
where and denote the particle positions and velocities, respectively. Here, , denote the hydrodynamic and contact forces, respectively. At every step, the overall stress in the suspension is fixed and is given by the sum of the hydrodynamic and contact contributions as follows:
Here, is the suspending liquid viscosity, , , and are the resistance matrices used to calculate the lubrication stress[5, 54], denotes the rate-of-strain tensor, and is the volume of the simulation box. and denote the position dependent resistance matrices containing the “squeeze,” “shear,” and “pump” modes of pairwise lubrication along with one-body Stokes drag. Imposing constant shear stress leads to a time-dependent shear rate , which is used to calculate the fluctuating viscosity .
Lubrication is regularized, allowing the particles to come into contact as the overlap becomes positive[5, 53]. Here, and are the particle radii, and and denote the position vectors of the center of particles and , respectively. In our simulations, we consider both normal and tangential frictional forces, i.e., ; tangential and normal contact forces satisfy , with being the static friction coefficient. We followed the approach of Cundall and Strack[55] and the algorithm by Luding[56] to model the contact between particles. Linear springs in the normal and tangential directions are used to model the contacts between particles. Both and are tuned to allow the maximum overlap to not exceed 3% of the particle size to maintain rigid particle approximation[57].
Finally, we employ the Critical Load Model (CLM) to introduce the rate dependence, where is required to activate the Coulombic static friction between the particles.
This critical force leads to a characteristic stress scale , such that for the particle interactions are lubricated, whereas for almost all contacts are frictional. For further details on the simulation scheme for modeling the hydrodynamics and contact forces, see[5, 7, 8, 52]. In the remainder of this work, quantities are reported in dimensionless form in terms of , and with .
Loop finding algorithm
This work focuses on the frictional contact network (FCN), which plays a crucial role in determining viscosity at high packing fractions and plays a key factor in discontinuous shear thickening (DST) and shear jamming (SJ) behaviors[5, 6, 7, 8, 26, 27, 28]. Figure 1a presents a typical FCN, as obtained from the simulations conducted in this study, where the red bonds represent the frictional contacts between the particles.
Figure 1. Decomposition of the frictional contact network into loops. (a) Simulation snapshot with frictional contact, where normal force exceeds the critical threshold, shown in red. (b) Frictional contact network in a, decomposed into loops. The loop shapes are filled according to the number of edges where warmer colors (yellow) indicate a larger loop order and cooler colors (purple) indicate a smaller loop order, as described in (c).
To analyze the data, we converted the physical space into a graph for each snapshot (Figure 1a). In graph theory, each particle is represented as a node, and an edge exists between the two nodes only if the particles are in frictional contact. By definition, the contact network is undirected and unweighted[43]. Note that we focus on the frictional contact network rather than the frictional force network, which is weighted (except for the analysis presented in Figure S1). We deal with a dynamic system, as the suspension is constantly under shear, meaning that contacts continually form, break, and reform. As a result, the network (or graph) is also dynamic and is analyzed snapshot by snapshot. A fundamental local property of any graph is the node degree, which, in an unweighted network, is simply the number of edges attached to a node. The mean degree for nodes is , often referred to as the coordination number . In this study, we use to denote the frictional coordination number or the number of frictional contacts per particle. In graph theory, a walk is a traversal from one node to another along the edges of a network. A simple path is a walk that does not revisit the same node or edge. A closed path is a special case where the walk returns to the starting node, which we refer to as a loop (or cycle, in some cases). A loop of order is a closed path traversing edges. In network science, the loops (or cycles) considered here are simple cycles, meaning no node or edge is revisited except for the starting and ending nodes. Thus, the smallest loop considered is a third-order loop. We refer to the non-closed paths as isolated edges or connected edges, depending on the number of nodes involved (Figure 1c).
Figure S1. Average stress contribution at for different type of loops at different packing fraction at
In this study, we restricted our analysis to loops of order , with the rationale for this limitation discussed at the end of the section. This approach is equivalent to identifying all loops from the third- to eighth-order. In our analysis, we prioritize the smaller-order loops. Specifically, if at least one edge in a loop of order does not belong to a loop of smaller order, all edges are initially assigned to the loop of order . During the assignment of edges to a specific loop of order , we encounter two possible scenarios: an edge may either belong exclusively to a particular loop, referred to as an “individual edge,” or it may be shared between two loops, referred to as a “shared edge” (Figure 2). Based on this classification, we assign attributes to the edges: a shared edge is assigned an attribute of 0.5, whereas an individual edge is assigned an attribute of 1. It is important to note that in a planar two-dimensional system, an edge can be shared by two loops, whereas in a three-dimensional system, the number of shared loops may be higher. An attribute of 0.5 in the case of shared edges ensures that while summing all the edges belonging to loops of different orders , we recover the degree of the network. Figure 2 illustrates this concept. The fifth-order loop (I) has three individual edges (solid lines) and two shared edges (dotted lines). We summarize the number of edges based on the edge attribution and divide the sum by the size of loops (five for the fifth order loop), which leads to 0.8 fifth order loops. Similarly, in this example, we have a 1.625 fourth-order loops and a 0.833 third-order loops.
Figure 2. Schematic of loop edge attribution. An example demonstrating the edge attribution while loops are counted. The solid and dotted lines represent the individual and shared edges, respectively. The numbers (I, II, III, and IV) denote and represent loops: fifth-order loop (I), fourth-order loop (II and III), and third-order loop (IV). The color coding for the loop is the same as in Figure 1.
Once all edges belonging to loops of orders 3–8 are found, the remaining edges are considered connected edges if at least one of the two nodes constituting that edge has at least one other frictional contact (Figure 1c). If neither node has another frictional contact, meaning that both nodes have a degree of one, then the edge is considered an isolated edge.
Our approach differs from previous methods, particularly the one proposed by Smart & Ottino[45], in two key ways: edge-centric approach and edge sharing. Smart and Ottino assert that every angle defined as two edges sharing a common vertex (AKA node) —must belong to only one loop, with the angle assigned to the smallest-order loop. By contrast, the algorithm presented in this study is based on edge allocation rather than angle allocation. When we tested alternative edge-sharing schemes, we found that the results for third-order loops were minimally affected, leading to the same conclusions. Ultimately, the edge-sharing scheme we presented was selected for its more concrete physical interpretation.
Finally, we provide the rationale for our choice of limiting the analysis to loops of order : (i) when calculating the average stress carried by each loop, we observe that loops up to the eighth-order typically carry the contact stress borne by the packing, while the contributions of higher-order loops are not significantly different from those of connected edges (Figure S1 in SI); (ii) In the context of subgraph isomorphism, loops with can exhibit numerous isomorphic cases, complicating the analysis; and (iii) the computational cost of detecting higher-order loops increases significantly, eventually becoming untractable. For these reasons, we restrict our focus to eighth-order loops in this study.
Simulations for a given condition were performed over 40 strain units with a strain step of . This sampling frequency ensures that each snapshot is statistically independent, meaning that each simulation snapshot samples a distinct ensemble of the frictional network (and thus loops). This independence allows for an accurate correlation between the network topology and strain-averaged rheological quantities, such as viscosity. At each step, we converted the snapshot to graph and applied the loop-detection algorithm to extract information about isolated edges, connected edges, and the number of loops for .
Results
Figure 1a shows a typical frictional contact network obtained from our simulation for the conditions . The line segments connecting the centers of the two particles in frictional contacts () are represented by red bonds. Applying our loop detection algorithm, we decompose this network of frictional contacts into loops of varying orders , illustrated as filled polygons with different numbers of sides, as shown in Figure 1b. The polygons are color-coded to indicate the loops of different sides, with the number of sides corresponding to “loop order .” Visual inspection revealed that our system consists of loops with orders ranging . Based on previous studies on dry granular materials, we focus primarily on low-order loops (3rd and 4th)[44, 45, 49]. Consistent with previous studies[45], we find that third and fourth order loops dominate the network and the number of loops decrease with loop order (Figure S2 in SI).
(a)
(b)
Figure S2. Number of loops as a function of loop order at (a) varying packing fraction at friction and (b) varying friction at packing fraction
Effect of packing density. We begin by examining the parameter space for in the vicinity of to explore the effects of increasing the packing fraction and the applied stress . Figure 3 presents a family of steady-state flow curves and the coordination number for various packing fractions . Figure 3a shows the canonical shear-thickening behavior observed in previous experimental[11, 24, 58, 59] and simulation[5, 6, 7] studies in three dimensions, showing a stress-driven transition between two rate-independent plateaus. Shear thickening behavior becomes more pronounced with increases with ; at and , continuous shear thickening (CST) is observed, while discontinuous shear thickening (DST) occurs at and , as indicated by the non-monotonic flow curve (inset of 3a). Furthermore, Figure 3b shows that this transition is driven by the activation of the frictional contacts. Initially, is zero at low stresses, and it increases once the stress exceeds a threshold of , eventually reaching a saturation point in the shear-thickened state. Notably, in the shear-thickened state increases with , which is consistent with the literature[39].
Figure 3. Rheology and coordination number. (a) Relative viscosity and (b) average coordination number as a function of scaled stress for different packing fractions for simulations with . With increasing , both and increase and saturate in the shear-thickened state. For (a), relative viscosity as a function of shear rate is shown in the inset. In 2D simulations performed here, DST occurs at roughly .
To gain mesoscale insight into DST, we analyze representative snapshots of frictional forces and their corresponding loop order-based decomposition as shown in the top and bottom panels of Figure 4, respectively. In Figure 4, we show the stress-induced frictional contact networks at various stages: the lubricated state (), onset of shear thickening (ST) (), DST regime (), and deep into the shear-thickened state (). At low stress , the suspension is in the lubricated state, with no frictional contacts. At , the force chains emerge as roughly linear structures along the compression axis of the simple shear flow resulting in only a few fleeting loops that usually appear at the meeting or splitting point of the force chains. At , frictional contacts form loops in the DST regime. Finally, at , the suspension reaches a fully shear-thickened state, and the network exhibits more loops than in the DST regime. Integrating these visual observations with the rheological data from Figure 3, we observe a clear correlation between shear thickening and network topology. Supplementary figures S3-S4 along with Video 1 show the evolution of interparticle forces and loops with packing fraction and strain for the systems shown in Figure 4 b-d.

Figure 4. Frictional contact network and corresponding loop structure. Simulation snapshot with frictional contact shown in red at four stress levels (): 0.1 (a), 1 (b), 5 (c) and 100 (d), for and . The loops of order are displayed using polygons with sides at stress levels (): 0.1 (e), 1 (f), 5 (g), and 100 (h). The color coding for the loop is the same as that in Figure 1.
To quantify these visual observations, snapshots are processed using the loop-detection algorithm to detect loops and extract the number of loops () across different packing fractions and stresses . First, we present the evolution of the non-closed structures, namely, isolated and connected edges, Figure 5 a and b, respectively. Both quantities start at zero in the frictionless state (blue shaded region), increase as the suspension undergoes shear thickening (green shaded region), and decrease once the stress surpasses . Note that both these quantities are insensitive to as the suspension shear thickens but show a decrease with . At intermediate stress values , most of the force chains are linear structures aligned along the compressive axis, increasing isolated and connected edges. However, as the number of frictional contacts increases further with stress , disconnected force chains are rare, giving way to loops that become more probable (Ref. Figure 4).

Figure 5. Evolution of non-closed components. The number of (a) isolated edges and (b) connected edges as a function of scaled stress at for different packing fractions . The blue blocks indicate the frictionless state where frictional contacts are absent; the green blocks indicate the stress regime where only linear force network (isolated and connected edges) are formed; the dashed lines indicate the point where higher order loop start to appear; and the red blocks show the shear-thickened stage.
Next, Figure 6 shows the evolution of the two smallest closed components, namely the third- and fourth-order loops, as a function of the scaled stress. Loops are absent for stresses , with both and remaining zero, and they begin to increase with stress thereafter. Notably, the stress at which the loops appear coincides with the stress at which the isolated and connected edges begin to decrease. We observe that both and increase with because the network becomes denser with increasing . As the packing fraction increases, increases more rapidly than . The analysis of for is provided in Supplementary Information (SI).

Figure 6. Evolution of loops. Number of (a) third order () and (b) forth order () loops as a function of scaled stress at for different packing fractions . The color coding for the loop is the same as in Figure 5.
The increase in (and ) with both and appears to correlate with the rheology of the dense frictional suspensions, as reflected in (and normal stresses, as presented in[7]). This correlation suggests that the mesoscale structure of the network, characterized by loop order, serves as a valuable order parameter that defines the macroscopic state of the material. The state of the material is reflected not only in the growth of frictional contacts but also in the evolving topological structure of the network as a function of stress and packing fraction.
Effect of friction. Previous studies have shown that the shear rheology of dense suspensions is governed by three key parameters: packing fraction , dimensionless shear stress , and the friction coefficient [5, 7, 8, 9]. After examining the effect of for , we now investigate the rheology and mesoscale network behavior for varying by sweeping through shear stress in the range at a constant .
Figure 7 illustrates the influence of the static friction coefficient on the steady-state viscosity and frictional coordination number . In agreement with previous studies[5, 7], we observe that significantly impacts the viscosity . Weak shear thickening is observed for , whereas a discontinuous shear thickening (DST) is observed for . Because frictional contacts in our simulations are stress-activated, the suspension behaves as frictionless at , making the viscosity independent of . As the stress increases, frictional contacts are activated. Therefore, the extent of shear thickening is determined by , where higher reduces making the shear thickening more severe.

Figure 7. Effect of friction. (a) Relative viscosity and (b) average coordination number as a function of scaled stress for different friction at . The inset in (a) shows relative viscosity as a function of shear rate showing DST for .
Figure 7b shows as a function of scaled stress . As increases, the force chains that bear the load are stabilized, allowing more frictional contacts to withstand external stress. This results in a higher steady-state average as a function of stress. This is also consistent with previous findings for dry granular materials[60].
To gain mesoscale insights into how friction affects the network topology, we use the loop-detection algorithm on simulation snapshots with different . The results for non-closed components, that is, isolated and connected edges, are presented in SI (Figure S6), where we find the results to be consistent with previous analysis of variation in (Ref. Figure 5). Next, Figure 8 shows the number of third- and fourth-order loops as a function of scaled stress at a constant packing fraction for different values of . We find that both and increase as increases, but there is a striking difference in the extent of their increase as changes. For example, at , increases roughly 7.5 times as increases from 0.1 to 10; while roughly doubles. This observation highlights that changes in the number of loops are not just a reflection of the increase in , but that the network is topologically different as increases.

Figure 8. Effect of friction on network topology. Number of (a) third-order loops () and (b) forth-order loops () as a function of scaled stress at packing fractions for different . The color coding for the loop is the same as that in Figure 5.

Figure S6. Number of (a) isolated edge and (b) connected edgeas a function of scaled stress at for different friction . The color coding for the loop is the same as in Fig.5 of the main text.
Connecting microscopic features with a macroscopic response via mesoscale features. Recent advances in the study of dense frictional suspensions suggest that the stress-induced frictional coordination number plays a crucial role in driving shear thickening behavior[3, 4, 5, 6, 28]. This raises an intriguing question: can the extensive data collected across a wide range of parameter spaces—spanning packing fraction and applied stress and friction coefficient —be collapsed by simply using the stress-activated frictional coordination number ?
We explore this idea in Figure 9a by plotting the viscosity against the frictional coordination number for all the data sets generated in this study. Contrary to our expectations, data collapse or a straightforward one-to-one relationship is not observed. Instead, the data suggest the presence of different families of curves, which do not converge into a single master curve. In contrast, plotting viscosity as a function of the number of third-order loops yields a better collapse of the data, Figure 9b. Figure 9b shows that the viscosity increases with and appears to diverge at a maximum . The solid line shows with and . The higher and data sets, in which DST or non-monotonic flow-curves are observed, follow this scaling law, while data sets with low do not agree with the proposed correlation. It is noteworthy that there are combinations of that have similar but different values of viscosity. Analyzing separates these data sets into two families, which we uncover below.

Figure 9. Connecting rheology with mesoscale network topology. Relative viscosity vs (a) frictional coordination number and (b) number of third order loops for data with variable friction at and variable packing fraction for . The solid line represents with and . (Inset) The same data on a log-log scale shows vs . The solid line shows the power law of .
From Figure 9b, we can observe that during shear thickening, the increase in viscosity follows a two-step process. The initial increase, roughly one order of magnitude, is primarily driven by an increase in the packing fraction and the activation of frictional contacts that do not necessarily form loops (only isolated and connected edges). At higher values of the parameter space , third-order loops, the smallest minimal rigid structures[51], begin to form, and their increase leads to a further increase in viscosity. In other words, a smaller number of third-order loops (which arise from low , , or values) results in lower viscosity , whereas a larger number of these loops provides local rigidity to the suspension, thereby increasing . The fact that the obtained master curve is independent of the packing fraction, shear stress, and interparticle friction underscores the critical role of mesoscale structure as the bridge connecting microscale properties (such as particle friction) to macroscale rheology. This correlation suggests that the viscosity is uniquely governed by the mesoscale topology, which we capture using the number of third-order loops. The observed diverging behavior implies that is regulated by or its distance from . It is important to note that different datasets corresponding to different values have varying intrinsic frictional jamming points , but their corresponding values remain similar. Finally, it is worth emphasizing that for a given combination of that results in the same at the mesoscale, the system exhibits a comparable macroscale response, specifically yielding the same relative viscosity.
Concluding Remarks
In this study, we focus on the topological features of the sub-network of frictional contacts in sheared dense suspensions since prior studies have shown that this sub-network drives strong shear-thickening[5, 7, 8, 33, 35]. We show that strong shear thickening arises from the mesoscale structures in the frictional network, which we identified as “loops.” We identified that third-order loops show a one-to-one correlation with the viscosity, which is insensitive to change in , , (given that stress is high enough, the coefficient of friction high enough (), and the packing fraction analyzed is close to ). We find the existence of higherorder loops , but none show a strong correlation with viscosity as presented by the third-order loops, being insensitive to the parameter space explored. At small stress, just at the onset of ST (and not DST), we find isolated and connected edges leading to an increase in viscosity. These structures do not contribute much to rigidity themselves but are needed to form third- and higher-order structures. Notably, we have explored the number of loops, not their interconnectivity or percolation. In fact, Supplementary Videos show that the loops are highly heterogeneous and the third-order loops never percolate and yet seem to relate to the viscosity divergence (Figure 9b). This highlights the subtlety of our findings that the increase in loops is not just a consequence of the increase in the coordination number but is also a product of the distinct topology as the system is sheared.
Relationship with Previous Studies. Our results highlight that a simple description of the network using the number of loops, particularly the number of third-order loops, —serves as a mesoscale order parameter, providing a unique prediction of rheological behavior. Notably, the independence of our master curve from is a significant finding, especially given that previous studies using minimal rigidity models, such as the pebble game, did not yield robust results with varying [38]. In the structural rigidity theory, a 3-cycle, the third-order loop (here), has been hypothesized to be the smallest minimal rigid structure in two dimensions. According to Lamans’ theorem, triangles are the smallest isostatic structures that do not continuously deform under externally applied load. In contrast, 4-cycles (or 4th-order loop, here) continuously deform from one configuration to another while preserving lengths and connectivity[51, 61, 62]. This could explain why is insensitive to , whereas is not (Figure S7, SI). In previous granular matter studies, even and odd order loops (or cycles) were also associated with allowing grains to roll and frustrated rotations, respectively[47]. Other studies have also interpreted contact loops as stabilizing mesoscale features in the context of jamming/unjamming and shear-banding[44, 45, 49, 63]. Thus, it is no surprise that we find that the third-order (and not fourth-order)loops to correlate remarkably with the viscosity.

Figure S7. Master curve of relative viscosity as a function of forth loop order
In this work, we focused on steady-state, strain-averaged mesoscale features and their relationship to rheology, leaving the exploration of temporal evolution and fluctuations for future studies. We only explored the mesoscale structure of the evolving contact network; future studies will relate the frustrated/free rotation of particles in an odd/even order loop, as shown in a dry granular context. We anticipate that our approach, which analyzes complex network structures in terms of loops, could offer valuable insights into the behavior of other amorphous materials, such as emulsions, colloidal gels, and foams.
Acknowledgments
A.S. acknowledges the Case Western Reserve University for start-up funding. This work used the High-Performance Computing Resource in the Core Facility for Advanced Research Computing at Case Western Reserve University.
References
Supplementary Information to: Topological insights into dense frictional suspension rheology: Third order loops drive discontinuous shear thickening
In this document, we provide details about (i) average stress contribution per loop order , (ii) number of loops vs , (iii) contact network evolution with strain, (iv) evolution of loop structure, (v) higher order loop -, (vi) isolated and connected edges for different , (vii) viscosity as a function of . These analyses complement the ones presented in the main text.
Loop Order Analysis
In the main text, we presented a rationale to constrain the loop calculation to . Figure S1 shows average stress carried by each loop order as a function of for and . We notice that isolated edges contribute minimally to stress, which is expected. It is also intuitive that the stress carried by each closed structure will increase with . Note that the increase in stress contribution for is minimal, almost collapsing with connected edges. Hence, we do not calculate structures beyond the eighth order, ensuring we preserve the important topological insights but making the computation tractable.
Loop Statistics
Previous studies[45] showed that the number of loops decrease with the order . We confirm this finding in Figure S2 with a subtle difference. First our overall findings are consistent with Smart & Ottino[45] that the number of loops decrease with increasing for all values of , , considered here. Smart & Ottino showed a decrease in third-order loops with increasing ; however we find the opposite trend. First, we highlight that the two systems (ours and one presented by Smart & Ottino) are different; we performed simulation at constant volume, whereas Smart & Ottino simulated constant pressure allowing the volume to fluctuate. In our system, increasing friction brings system closer to its frictional jamming point thus allowing more locally rigid structures (third-order loops) to form.
Evolution of frictional contact network
Figure 4 of the main text shows a representative snapshot for various values of . Figure S3 shows the frictional contact network for a few more strain values confirming that: (i) we indeed attain the steady state; (ii) at different snapshots (especially for ) brings different particles into contacts highlighting the dynamic nature of our simulations.

Figure S3. Strain evolution of frictional contact network at friction and packing fraction at three stress levels : 1, 5 and 100. Strain increases from left to right. The frictional contacts are shown in red.
Evolution of network topology
Figure 4 of the main text shows a representative snapshot and corresponding loop structure for various values of . Figure S4 shows the loop structure obtained from the frictional contact network for a few more strain values.

Figure S4. Time evolution of loops at friction and packing fraction at three stress levels : 1, 5. The color coding for the loop is the same as in Figure 1 of the main text. Strain increases from left to right.
Evolution of higher-order loops -
In the main text, we only presented the isolated- and connected-edges along with third- and fourth-order loops. Figure S5 shows the evolution of fifth to eight-order loops as a function of for various values of for . We observe that the sensitivity to increase in decreases as the loop order increases. As an example, at a stress of 100, increases roughly 1.6 folds as volume fraction increases, shows barely any change with (at the same stress). is roughly insensitive to at higher stresses.

Figure S5. Number of (a) fifth order loop (), (b) sixth order loop (), (c) seventh order loop () and (d) eighth order loop () as a function of scaled stress at for different packing fractions . The color coding for the loop is the same as in Fig.5. of the main text.
Evolution of isolated and connected-edges for different
In the main text, we only presented the evolution of third- and fourth-order loops for simulations with different . Figure S6 shows the evolution of isolated- and connected-edges as a function of stress for different values of . We observe that increasing leads to a decrease in isolated and connected edges at higher stresses.
Viscosity as a function of number of fourth order loops
Figure S7 shows viscosity plotted as a function of the number of fourth-order loops for all the simulation data presented in this study. We do not observe the data has a reasonable collapse as analyzed for a constant ; while data for different friction, falls off the collapse (or master curve). This highlights the significance of third-order loops as compared to the fourth-order loops.
Movie
The movie shows the evolution of network topology (loops) with packing fraction and stress in Fig. b-d (and f-h) of the main text.
References
- [1]1E. Brown and H. M. Jaeger, “Shear thickening in concentrated suspensions: phenomenology, mechanisms and relations to jamming,” Reports on Progress in Physics 77, 046602 (2014).
- [2]2J. F. Morris, “Shear thickening of concentrated suspensions: Recent developments and relation to other phenomena,” Annual Review of Fluid Mechanics 52, 121–144 (2020).DOI
- [3]A. Singh, “Hidden hierarchy in the rheology of dense suspensions,” MRS Communications 13, 971–979 (2023).arxiv.org/abs/2305.13586
- [4]M. Wyart and M. E. Cates, “Discontinuous shear thickening without inertia in dense non-Brownian suspensions,” Physical Review Letters 112, 098302 (2014).pubmed.ncbi.nlm.nih.gov/24655284
- [5]R. Mari, R. Seto, J. F. Morris, and M. M. Denn, “Shear thickening, frictionless and frictional rheologies in non-Brownian suspensions,” Journal of Rheology 58, 1693–1724 (2014).DOI
- [6]C. Ness and J. Sun, “Shear thickening regimes of dense non-Brownian suspensions,” Soft Matter 12, 914–924 (2016).
- [7]A. Singh, R. Mari, M. M. Denn, and J. F. Morris, “A constitutive model for simple shear of dense frictional suspensions,” Journal of Rheology 62, 457–468 (2018).
- [8]A. Singh, C. Ness, R. Seto, J. J. de Pablo, and H. M. Jaeger, “Shear thickening and jamming of dense suspensions: The “roll” of friction,” Physical Review Letters 124, 248005 (2020).DOI
- [9]A. Singh, G. L. Jackson, M. van der Naald, J. J. de Pablo, and H. M. Jaeger, “Stress-activated constraints in dense suspension rheology,” Physical Review Fluids 7, 054302 (2022).DOI
- [10]B. J. Maranzano and N. J. Wagner, “The effects of particle size on reversible shear thickening of concentrated colloidal dispersions,” Journal of Chemical Physics 114, 10514–527 (2001).DOI
- [11]B. M. Guy, M. Hermes, and W. C. K. Poon, “Towards a unified description of the rheology of hard-particle suspensions,” Physical Review Letters 115, 088304 (2015).pubmed.ncbi.nlm.nih.gov/26340217
- [12]B. J. Maranzano and N. J. Wagner, “The effects of interparticle interactions and particle size on reversible shear thickening: Hard-sphere colloidal dispersions,” Journal of Rheology 45, 1205–1222 (2001).DOI
- [13]N. M. James, E. Han, R. A. L. de la Cruz, J. Jureller, and H. M. Jaeger, “Interparticle hydrogen bonding can elicit shear jamming in dense suspensions,” Nat. Mater. 17, 965 (2018).DOI
- [14]H. M. Laun, “Rheological properties of aqueous polymer dispersions,” Angew. Makromol. Chem. 123, 335–359 (1984).DOI
- [15]I. R. Peters, S. Majumdar, and H. M. Jaeger, “Direct observation of dynamic shear jamming in dense suspensions,” Nature 532, 214–217 (2016).DOI
- [16]S. Barik and S. Majumdar, “Origin of two distinct stress relaxation regimes in shear jammed dense suspensions,” Physical Review Letters 128, 258002 (2022).DOI
- [17]E. Zaccarelli, “Colloidal gels: equilibrium and non-equilibrium routes,” Journal of Physics: Condensed Matter 19, 323101 (2007).
- [18]H. Vinutha, F. D. Diaz Ruiz, X. Mao, B. Chakraborty, and E. Del Gado, “Stress–stress correlations reveal force chains in gels,” The Journal of chemical physics 158 (2023).DOI
- [19]D. Mangal, M. Nabizadeh, and S. Jamali, “Topological origins of yielding in short-ranged weakly attractive colloidal gels,” The Journal of Chemical Physics 158 (2023).DOI
- [20]E. D. Gado, D. Fiocco, G. Foffi, S. Manley, V. Trappe, and A. Zaccone, “Colloidal gelation,” Fluids, Colloids and Soft Materials: An Introduction to Soft Matter Physics , 279–291 (2016).DOI
- [21]D. Bi, J. Zhang, B. Chakraborty, and R. P. Behringer, “Jamming by shear,” Nature 480, 355–358 (2011).DOI
- [22]M. E. Cates, J. P. Wittmer, J.-P. Bouchaud, and P. Claudin, “Jamming, force chains, and fragile matter,” Phys. Rev. Lett. 81, 1841–1844 (1998).DOI
- [23]R. Seto, A. Singh, B. Chakraborty, M. M. Denn, and J. F. Morris, “Shear jamming and fragility in dense suspensions,” Gran. Matt. 21, 82 (2019).DOI
- [24]B. M. Guy, J. Richards, D. Hodgson, E. Blanco, and W. C. K. Poon, “Constraint-based approach to granular dispersion rheology,” Physical Review Letters 121, 128001 (2018).DOI
- [25]A. Singh, C. Ness, A. K. Sharma, J. J. de Pablo, and H. M. Jaeger, “Rheology of bidisperse non-brownian suspensions,” Physical Review E 110, 034901 (2024).DOI
- [26]C.-P. Hsu, S. N. Ramakrishna, M. Zanini, N. D. Spencer, and L. Isa, “Roughness-dependent tribology effects on discontinuous shear thickening,” Proc. Nat. Acad. Sci. (2018).DOI
- [27]C. Clavaud, A. Bérut, B. Metzger, and Y. Forterre, “Revealing the frictional transition in shear-thickening suspensions,” Proc. Natl. Acad. Sci. U.S.A. , 5147–5152 (2017).DOI
- [28]R. Seto, R. Mari, J. F. Morris, and M. M. Denn, “Discontinuous shear thickening of frictional hard-sphere suspensions,” Physical Review Letters 111, 218301 (2013).DOI
- [29]S. Jamali and J. F. Brady, “Alternative frictional model for discontinuous shear thickening of dense suspensions: Hydrodynamics,” Physical Review Letters 123, 138002 (2019).DOI
- [30]E. Han, N. M. James, and H. M. Jaeger, “Stress controlled rheology of dense suspensions using transient flows,” Phys. Rev. Lett. 123, 248002 (2019).DOI
- [31]M. Ramaswamy, I. Griniasty, D. B. Liarte, A. Shetty, E. Katifori, E. Del Gado, J. P. Sethna, B. Chakraborty, and I. Cohen, “Universal scaling of shear thickening transitions,” Journal of Rheology 67, 1189–1197 (2023).arxiv.org/abs/2107.13338
- [32]A. Boromand, S. Jamali, B. Grove, and J. M. Maia, “A generalized frictional and hydrodynamic model of the dynamics and structure of dense colloidal suspensions,” Journal of Rheology 62, 905–918 (2018).
- [33]J. E. Thomas, K. Ramola, A. Singh, R. Mari, J. F. Morris, and B. Chakraborty, “Microscopic origin of frictional rheology in dense suspensions: correlations in force space,” Phys. Rev. Lett. 121, 128002 (2018).DOI
- [34]O. Sedes, H. A. Makse, B. Chakraborty, and J. F. Morris, “K-core analysis of shear-thickening suspensions,” Physical Review Fluids 7, 024304 (2022).arxiv.org/abs/2108.07261
- [35]M. Gameiro, A. Singh, L. Kondic, K. Mischaikow, and J. F. Morris, “Interaction network analysis in shear thickening suspensions,” Physical Review Fluids 5, 034307 (2020).DOI
- [36]L. E. Edens, S. Pednekar, J. F. Morris, G. K. Schenter, A. E. Clark, and J. Chun, “Global topology of contact force networks: Insight into shear thickening suspensions,” Physical Review E 99, 012607 (2019).DOI
- [37]L. E. Edens, E. G. Alvarado, A. Singh, J. F. Morris, G. K. Schenter, J. Chun, and A. E. Clark, “Shear stress dependence of force networks in 3d dense suspensions,” Soft Matter 17, 7476–7486 (2021).DOI
- [38]M. van der Naald, A. Singh, T. T. Eid, K. Tang, J. J. de Pablo, and H. M. Jaeger, “Minimally rigid clusters in dense suspension flow,” Nature Physics , 1–7 (2024).DOI
- [39]M. Nabizadeh, A. Singh, and S. Jamali, “Structure and dynamics of force clusters and networks in shear thickening suspensions,” Physical Review Letters 129, 068001 (2022).DOI
- [40]A. Goyal, N. S. Martys, and E. Del Gado, “Flow induced rigidity percolation in shear thickening suspensions,” arXiv preprint arXiv:2210.00337 (2022).arxiv.org/abs/2210.00337
- [41]M. Nabizadeh, F. Nasirian, X. Li, Y. Saraswat, R. Waheibi, L. C. Hsiao, D. Bi, B. Ravandi, and S. Jamali, “Network physics of attractive colloidal gels: Resilience, rigidity, and phase diagram,” Proceedings of the National Academy of Sciences 121, e2316394121 (2024).DOI
- [42]J. E. Thomas, A. Goyal, D. Singh Bedi, A. Singh, E. Del Gado, and B. Chakraborty, “Investigating the nature of discontinuous shear thickening: Beyond a mean-field description,” Journal of Rheology 64, 329–341 (2020).DOI
- [43]L. Papadopoulos, M. A. Porter, K. E. Daniels, and D. S. Bassett, “Network analysis of particles and grains,” Journal of Complex Networks 6, 485–565 (2018).
- [44]R. Arévalo, I. Zuriguel, S. A. Trevijano, and D. Maza, “Third order loops of contacts in a granular force network,” International Journal of Bifurcation and Chaos 20, 897–903 (2010).DOI
- [45]A. G. Smart and J. M. Ottino, “Evolving loop structure in gradually tilted two-dimensional granular packings,” Physical Review E—Statistical, Nonlinear, and Soft Matter Physics 77, 041307 (2008).pubmed.ncbi.nlm.nih.gov/18517610
- [46]N. R. Blackett, “Disclination lines in glasses,” Philosophical Magazine A 40, 859–868 (1979).
- [47]N. Rivier, “Extended constraints, arches and soft modes in granular materials,” Journal of Non-Crystalline Solids 352, 4505–4508 (2006), proceedings of the 5th International Discussion Meeting on Relaxations in Complex Systems.DOI
- [48]C. Mankoc, A. Janda, R. Arévalo, J. M. Pastor, I. Zuriguel, A. Garcimartín, and D. Maza, “The flow rate of granular materials through an orifice,” (2007), arXiv:0707.4550 [cond-mat.soft].arxiv.org/abs/0707.4550
- [49]A. Tordesillas, D. M. Walker, and Q. Lin, “Force cycles and force chains,” Phys. Rev. E 81, 011302 (2010).pubmed.ncbi.nlm.nih.gov/20365363
- [50]C. Giusti, L. Papadopoulos, E. T. Owens, K. E. Daniels, and D. S. Bassett, “Topological and geometric measurements of force-chain structure,” Phys. Rev. E 94, 032909 (2016).DOI
- [51]G. Laman, “On graphs and rigidity of plane skeletal structures,” Journal of Engineering mathematics 4, 331–340 (1970).DOI
- [52]R. Mari, R. Seto, J. F. Morris, and M. M. Denn, “Nonmonotonic flow curves of shear thickening suspensions,” Physical Review E 91, 052302 (2015).pubmed.ncbi.nlm.nih.gov/26066172
- [53]R. C. Ball and J. R. Melrose, “Lubrication breakdown in hydrodynamic simulations of concentrated colloids,” Adv. Colloid Interface Sci. 59, 19–30 (1995).DOI
- [54]D. J. Jeffrey, “The calculation of the low Reynolds number resistance functions for two unequal spheres,” Phys. Fluids A 4, 16–29 (1992).DOI
- [55]P. A. Cundall and O. D. L. Strack, “A discrete numerical model for granular assemblies,” Geotechnique 29, 47–65 (1979).DOI
- [56]S. Luding, “Cohesive, frictional powders: contact models for tension,” Gran. Matt. 10, 235–246 (2008).DOI
- [57]A. Singh, V. Magnanimo, K. Saitoh, and S. Luding, “The role of gravity or pressure and contact stiffness in granular rheology,” New J. Phys 17, 043028 (2015).
- [58]C. D. Cwalina and N. J. Wagner, “Material properties of the shear-thickened state in concentrated near hard-sphere colloidal dispersions,” J. Rheol. 58, 949–967 (2014).
- [59]J. R. Royer, D. L. Blair, and S. D. Hudson, “Rheological signature of frictional interactions in shear thickening suspensions,” Phys. Rev. Lett. 116, 188301 (2016).DOI
- [60]A. Singh, V. Magnanimo, and S. Luding, “Effect of friction and cohesion on anisotropy in quasi-static granular materials under shear,” in AIP Conference Proceedings, Vol. 1542 (American Institute of Physics, 2013) pp. 682–685.DOI
- [61]L. Asimow and B. Roth, “The rigidity of graphs,” Transactions of the American Mathematical Society 245, 279–289 (1978).DOI
- [62]H. Crapo, “Structural rigidity,” Structural topology, 1979, núm. 1 (1979).
- [63]D. M. Walker and A. Tordesillas, “Topological evolution in dense granular materials: a complex networks perspective,” International Journal of Solids and Structures 47, 624–639 (2010).DOI





