betaFeedback

WorksPhysics and Astronomy

Acoustic Zero-Index Metamaterials for Leaky-Wave Antennas

Abstract

In this work, we introduce an advanced acoustic leaky-wave antenna employing zero-refractive-index metamaterials (ZIMs) that significantly surpasses traditional designs in terms of radiation ef-ficiency and directivity. Our design features a novel space-coiling structure, which manipulates the Dirac-like dispersion based on accidental degeneracy to achieve double-zero-index metamaterials (DZIM). The newly developed acoustic Dirac leaky-wave antenna (ADLWA) achieves more than double the radiation efficiency of conventional antennas based on arrays with side holes and mem-branes. It exhibits superior directional control, allowing for precise beam scanning by adjusting the frequency. Additionally, the ADLWA functions effectively as a passive sonar system, capable of de-tecting the direction of moving sound sources. This breakthrough enhances acoustic wave control and promises significant advancements in sensing and communication technologies.

Introduction

Acoustic leaky wave antennas (ALWAs) are passive, dispersive waveguides that have been extensively explored for their capability to achieve frequency-dependent directional radiation scanning. Generally, conventional ALWAs are composed of waveguiding materials with periodic side holes, supporting only right-hand (RH) propagation and allowing forward radiation [1]. Composite Right/Left-Hand Transmission Line (CRLH-TL) metamaterials [2, 3], which enable both right-hand (RH) and left-hand (LH) propagation to facilitate the transition of the main radiation beam from backward to forward radiation, have been introduced into ALWAs [4]. In prior research, by incorporating periodic arrays of side holes and membranes along the waveguide [5, 6], the design of these CRLH-TL ALWAs enables the wavenumber to shift continuously from negative to positive, without the presence of stopband. Many studies based on this structure were expanded [1, 7, 8, 9, 10, 11, 12, 13, 14, 15], such as acoustic dispersive prisms [12] and single-microphone acoustic source direction finding [13, 14]. More recently, heterostructures [14] and gradient-distributed structural units [15] have been designed to achieve higher directivity. Additionally, underwater acoustic leaky-wave technologies have been introduced [16, 17, 18]. However, LWA structures with side holes and membrane arrays often face issues such as complex assembly, challenging membrane tension control, high losses, and large side lobes. Their maximum radiation efficiency ranges from a few percent [12] to 25% [4].

Zero-refractive-index metamaterials (ZIMs) are a class of unconventional materials characterized by a refractive index of zero [19, 20, 21, 22, 23, 24]. In ZIMs, the phase velocity becomes infinite, resulting in no spatial phase change. This exhibits remarkable properties such as super-coupling [25, 26, 27], cloaking effects [28, 29, 30, 31], and wave front engineering [32, 33, 34]. Recently, ZIMs have demonstrated a unique beam-collimating effect, producing highly directional beams in the far field [35, 36, 37]. This material overcomes the limitations of conventional antennas, where directivity is typically constrained by the nonuniform spatial phase distribution across the radiation aperture, ultimately approaching the fundamental directivity limit of previous antenna designs [35, 37]. This advancement opens new avenues for enhancing acoustic antenna technology. Therefore, integrating ZIMs with ALWAs holds significant potential for achieving higher radiation efficiency and improved directivity. To achieve ZIMs, various approaches have been explored, including the use of membranes [26, 38], Helmholtz resonators [39, 40, 41], and waveguides [25, 42]. In optics, lossless double-zero-index metamaterials (DZIMs) are typically realized using photonic crystals composed of high refractive index scatterers that exhibit a Dirac-like cone induced by accidental degeneracy, resulting in both zero permittivity and permeability [20]. However, realizing a similar mechanism directly in air remains challenging due to the significantly slower speed of sound in air compared to solids and liquids. Prior acoustic DZIMs have primarily been developed in water [27, 43], elastic wave [23], high-order waveguides [44], flat dispersion [30], Helmholtz resonators [40], or 3D configurations [45, 46]. In recent years, the space-coiling structure demonstrates a high capacity for novel acoustic wavefront manipulation by effectively increasing the refractive index through air folding and prolonging sound propagation time [47, 48, 49, 50, 51]. We speculate that this structure could be an ideal candidate for realizing acoustic DZIMs in 2D air media.

In this letter, we introduce a novel space-coiling structure with variable channel spacing that effectively disrupts the inherent multipole degeneracy of traditional designs [52]. Through precise manipulation, we achieved a low-frequency subwavelength Dirac-like point at the center of the Brillouin zone, accompanied by the manifestation of double zero effective parameters. The DZIM is arranged periodically in a one-dimensional waveguide, forming an acoustic Dirac leaky-wave antenna (ADLWA). This newly designed ADLWA demonstrates the ability to radiate through broadside while dynamically scanning the directive beam by frequency variation. Distinctively, the ADLWA features a closed stopband, matched response, and a consistent leakage constant around broadside, significantly enhancing its directivity and more than doubling its radiation efficiency relative to conventional LWAs. Moreover, this ADLWA also function as a passive sonar system, adept at locating moving sound sources in space independently of its physical length.

Design of the DZIMs

Design of the DZIMs

Acoustic multiple Mie resonance has been found to occur in space-coiling structure [47], which provided novel abilities of wave manipulation by generating a negative bulk modulus with a negative mass density at resonance. It was found in [52] that in this intriguing type of resonance, Mie resonance frequencies of various orders overlap, that is, degenerate Mie resonance. This mechanism is enabled by the anisotropic character of the effective mass density. It has been shown that the accidentally degenerate Dirac cone of dipole mode and monopole mode at the Γ\Gamma point can be mapped to a double zero [20].

In this work, we enhance traditional space-coiling metamaterials by introducing variable channel spacing, unlike the conventional constant width. This innovative design significantly enhances the tunability of the material's equivalent constitutive properties, thereby offering a more flexible approach to the customization of its acoustic responses. As shown in Figure 1(a), the lattice constant is denoted by aa, hard solid plates with thickness tt are embedded into the background fluid, creating zigzag channels. The width of each channel is treated as a design variable, allowing for precise manipulation of the channel geometry. In this work, we engineer the unit cell to induce accidental degeneracy between the dipolar and monopolar modes. Considering that the acoustic Mie resonance monopole fields are primarily localized near the center, while dipole fields are localized in regions farther from the center, as illustrated in Figure 1(a), the varying widths of the inner and outer channels can independently adjust the positions of monopole and dipole frequencies until degeneracy, or even effectively eliminating the influence of quadrupoles.

Schematic diagram of the designed space-coiling structure and corresponding properties of the metamaterial

Figure 1. Schematic diagram of the designed space coiling structure and the corresponding properties of the metamaterial. (a) The structure with four zigzag channels. The rigid wall (thin solid lines) inserted into air (gray color) forms a zigzag channel with opening width and outer channel width w2=0.114aw_2 = 0.114a, inner channel width w1=0.02aw_1 = 0.02a, inner radius R0=0.08aR_0 = 0.08a, and outside radius R1=0.427aR_1 = 0.427a. (b) Comparison of band structure of DZIM computed by determining the angular frequencies as a function of wave vector for all the Bloch modes (black dot), and by k=neffω/ck = n_{eff}\omega/c with the retrieved effective index neffn_{eff} (red curve). The inset is eigenmodes near the Dirac-like point with a small kk along ΓX\Gamma X direction. The effective (c) mass density ρeff\rho_{eff} (black line), reciprocal of bulk modulus 1/κeff1/\kappa_{eff} (blue line), (d) impedance ZZ (grey line) and refractive index neffn_{eff} (red line) as a function of frequency near the Dirac-like point.

Figure 1(b) shows that along the ΓX\Gamma X direction, two branches with linear dispersion intersect at the degeneracy point k=0k=0, forming a Dirac-like point at ω=0.306(2πv/a)\omega=0.306(2\pi v/a). Notably, this represents a triply degenerate state, including a monopolar mode as depicted in the inset, a dipolar longitudinal mode along the ΓX\Gamma X direction, and a transverse mode forming a flat band (as shown in Fig. S1 in supplementary). This degeneracy arises accidentally, thus, altering the geometric parameters can split this triply degenerate state into a doubly degenerate state and a single state. The cone dispersion can be mapped to DZIM, where the reciprocal of the effective bulk modulus 1/κeff1/\kappa_{\mathrm{eff}} and the effective mass density ρeff\rho_{\mathrm{eff}} both approach zero. Figure 1(e) illustrates the effective mass density ρeff\rho_{\mathrm{eff}} (black solid line) and the reciprocal of the bulk modulus 1/κeff1/\kappa_{\mathrm{eff}} (blue solid line) as a function of frequency, based on field averaging [53, 54], intersecting at zero at the Dirac point frequency ω=0.306(2πv/a)\omega=0.306(2\pi v/a). At this frequency, the structure also exhibits an effective refractive index near zero and an effective impedance close to that of the background air, as shown in Figure 1(d). To quantitatively evaluate whether the effective constitutive parameters are valid, we obtain the dispersion curve as (k=neffω/c)(k=n_{\mathrm{eff}}\omega/c) (red solid line in Figure 1(b)), based on ρeff\rho_{\mathrm{eff}} and 1/κeff1/\kappa_{\mathrm{eff}}. The close correlation between the analytical and numerical results confirms that the effective homogeneous medium approximation accurately describes the metamaterials composed of space-coiling structure near the Dirac point frequency for this configuration.

Acoustic Dirac Leaky wave antenna (ADLWA)

To facilitate effective coupling between the metamaterial and propagating waves in air, an interface between the metamaterial and air must be designed to support the propagation of leaky modes. Crucially, this propagation needs to persist at the Γ\Gamma-point without a frequency gap [55]. This enables continuous scanning from backward to forward radiation, leading to the formation of the ADLWA. According to previous work [18, 19, 20], short shunt tubes can be used between background air and waveguide in traditional acoustic LWAs to create a leaky interface, depending on the specific geometry requirements.

of the slots. (c) A three-dimensional view of the 35-cells ADLWA, formed by cascading unit cells of the leaky Dirac metamaterials.

Here, we employ a more straightforward leakage mechanism by considering the top-perforated unit cell, as shown in Figure 2(a) and (Figure 2b). Notably, the introduction of perforations disrupts and shifts the original Dirac point, as compared to the unperforated DZIM in the waveguide. Numerical results show that by fine-tuning the geometry of the radiation apertures, the two orthogonal Bloch eigenmodes of the original DZIM within the waveguide can re-degenerate. These apertures, which can vary in shape, being either circular or rectangular, are strategically placed to maintain the waveguide's ability to support its original modes. Specifically, the size of the slot can adjust the imaginary part of the eigenfrequency, that is, the leakage factor of the leakage mode unit. As shown in Figure 2(b), the left slot (yellow area) and right slot (green area) are used to adjust the eigenfrequency of the dipole mode and monopole mode separately. The relevant geometric parameters are ϕ0=37∘\phi_0 = 37^\circ, ϕ1=30∘\phi_1 = 30^\circ, ϕ2=55∘\phi_2 = 55^\circ, da=0.07ad_a = 0.07a, db=0.343ad_b = 0.343a, sx=0.0456as_x = 0.0456a, sa=0.148as_a = 0.148a, sb=0.114as_b = 0.114a, lz=0.656al_z = 0.656a. The 2 leaky modes have finite (due to radiation) and comparable quality factors Qd=150.6Q_d = 150.6 and Qm=94.9Q_m = 94.9.The ADLWA presented in Figure 2(c) features a 3D view of the 35 cells. This antenna is constructed by directly cascading the unit cells of the previously described leaky Dirac metamaterials. As the frequency of the incident wave varies, the group velocity and the propagation constant of the metamaterial shifts from negative to positive. This enables it can continuous radiation scanning from backward to forward in the xzxz-plane. In other words, the phase constant β\beta along the xx-direction determines the primary radiation angle θ\theta for the DLWA. This relationship can be expressed as

Figure 2. The leaky Dirac metamaterial. (a) Unit cell of one-dimensional Dirac metamaterials with top perforations featuring 4 slots (yellow and green rectangles) in the acoustic waveguide. The periodicity is in the x-direction. (b) The top view of the unit cell shows the location

θ(f)=sin⁡β(f)k0(1)\theta(f) = \sin\frac{\beta(f)}{k_0} \tag*{(1)}

Where k0k_0 is the wave vector of the ambient medium.

Leaky wave antennas are commonly analyzed using transmission line theory (TLs), which is a circuit-based concept that can describe wave propagation across various systems [14, 56]. We utilize a circuit model to analyze our leaky metamaterials. It should be noted that the typical one-to-one correspondence [12, 13, 14, 15, 16, 17, 18, 19, 20, 21] between structure and circuit components may not be readily apparent in this structure. As illustrated in Figure 3a, distinct series and shunt resonators were used, akin to the modeling approach in [15], to represent different resonant modes. Each mode is effectively modeled by either an inductor/capacitor resonator, ensuring that the circuit elements corresponding to these resonances remain distinct. This unit cell circuit model decouples the two resonances, mirroring the orthogonal eigenmodes of the metamaterial unit. Since each mode exhibits a finite Q-factor due to radiation losses, the circuit model includes both lossy series and shunt resonators, represented by resistor/LC (RLC) or conductance/LC (GLC) configurations. The corresponding series impedance ZseZ_{se} and parallel admittance YshY_{sh} are characterized as follows:

Schematic diagram and equivalent acoustic transmission line circuit for a single unit, two-port acoustic transmission, two-port network matrix, and frequency response plots

Figure 3. (a) Illustrate the schematic diagram and the equivalent acoustic transmission line circuit for a single unit. (b) Two-port acoustic transmission of a metamaterial unit. (c) Characterization of a two-port network using the [ABCD] matrix in a circuit mode. In the 35-unit

Zse=Rse+jωLse+1jωCse(2)Z_{se} = R_{se} + j\omega L_{se} + \frac{1}{j\omega C_{se}} \tag*{(2)}
Ysh=Gsh+jωCsh+1jωLsh(3)Y_{sh} = G_{sh} + j\omega C_{sh} + \frac{1}{j\omega L_{sh}} \tag*{(3)}

simulation, characterization of series and parallel loss resonance in unit cells includes: (d) extracting the reciprocal of the B element from the unit transfer matrix ABCD near the Γ\Gamma point (dashed line) and fitting the curve of the circuit model Zse−1Z_{se}^{-1} (solid line); (e) extracting the reciprocal of the C element from the unit transmission matrix ABCD near the Γ\Gamma point (dashed line) and fitting the curve for the circuit Ysh−1Y_{sh}^{-1} (solid line).

This straightforward model offers several key insights into the behavior of ADLWA, such as verifying that the stopband is closed and that a real, constant Bloch impedance near the broadside frequency enables matched operation. During resonance, both the impedance and admittance become purely real, specifically, Zse=RseZ_{se}=R_{se}, Ysh=GshY_{sh}=G_{sh}. Consequently, the resonance frequencies, fsef_{se} and fshf_{sh}, are defined as follows:

fse=12πLseCse(4)f_{se}=\frac{1}{2\pi\sqrt{L_{se}C_{se}}} \tag*{(4)}
fsh=12πLshCsh(5)f_{sh}=\frac{1}{2\pi\sqrt{L_{sh}C_{sh}}} \tag*{(5)}

In our acoustic circuit modeling, voltage corresponds to acoustic pressure pp and current to volume velocity qq. We suggest that the transmission properties of a single unit cell from the leaky Dirac metamaterials, as shown in Figure 3(b) (based on full-wave simulations), can be effectively modeled by the ABCD matrix of a two-resonator circuit at the degeneracy frequency, as depicted in Figure 3(c). This approach enables the use of a simple circuit model to represent the two-port behavior of the unit cell, thereby elucidating its dispersion and matching characteristics. The two-port S-parameters of the 35-cell antenna can be obtained through full-wave simulations in COMSOL, and subsequently converted to an ABCDABCD transmission matrix. To derive the ABCD matrix of a single cell, we use ABCD1=ABCD3535ABCD_1=\sqrt[35]{ABCD_{35}}, where ABCD1ABCD_1 and ABCD35ABCD_{35} represent the matrices for a single unit cell and the 35-cell structure, respectively. We then determine critical parameters such as phase (β\beta) and leakage (α\alpha) constants, Bloch impedance (ZbZ_b) and other relevant circuit model parameters from ABCD1ABCD_1. For structures with 45 and 55 cells, the matrices ABCD1=ABCD4545ABCD_1=\sqrt[45]{ABCD_{45}} and ABCD1=ABCD5555ABCD_1=\sqrt[55]{ABCD_{55}} are calculated similarly.

In transmission line theory, when there are periodic circuit components, the ABCD matrix of a circuit having both a series impedance (ZseZ_{se}) and a shunt admittance (YshY_{sh}) is [4, 15, 57]:

ABCDse×sh=ABCDse×ABCDsh=[1+ZseYshZseYsh1](6)ABCD_{se\times sh}=ABCD_{se}\times ABCD_{sh}= \begin{bmatrix} 1+Z_{se}Y_{sh} & Z_{se}\\ Y_{sh} & 1 \end{bmatrix} \tag*{(6)}

This indicates that analyzing the B and C elements of the ABCD matrix for this circuit separately reveals the series impedance and shunt admittance, respectively. Subsequent examination of the ABCD1ABCD_1 matrix is detailed in Figure 3(d) and Figure 3(e), which plot the complex values of the inverse B and C elements across frequencies (represented as red and blue dashed lines, respectively) for the purpose of model extraction. The presence of distinct resonances corresponding to each matrix element solidifies the validity of our series/shunt model, effectively encapsulating the two-port functionality of the unit cell in a coherent manner. As noted, frequencies at which B and C's imaginary parts reach zero define the resonant frequencies (fsef_{se} and fshf_{sh}), and their real components are set as RseR_{se} and GshG_{sh}. Using curve fitting, we calculate the inductances (LshL_{sh} and LseL_{se}) and model CshC_{sh} and CseC_{se} as functions of these inductances, according to Eqs. (4) and (5). As illustrated in Figure 3(d) and Figure 3(e), the resonance parameters modeled using transmission line theory and extracted via full-wave simulation show a strong correlation. The extracted resonances (fse∼fsh∼1554f_{se}\sim f_{sh}\sim1554 Hz) and the fitted model parameters (Rse=19.0912 ΩR_{se}=19.0912\ \Omega, Lse=0.85 HL_{se}=0.85\ \mathrm{H}, Cse=1.234⋅10−8 FC_{se}=1.234\cdot10^{-8}\ \mathrm{F}, Gsh=1.491⋅10−5 Ω−1G_{sh}=1.491\cdot10^{-5}\ \Omega^{-1}, Lsh=8.8⋅10−3 HL_{sh}=8.8\cdot10^{-3}\ \mathrm{H}, Csh=1.192⋅10−6 FC_{sh}=1.192\cdot10^{-6}\ \mathrm{F}) verifies that the structure's stopband is conclusively closed, indicating a balanced condition. The propagation of acoustic waves through the periodic structure is analyzed using Bloch theory, which is based on the unit cell. The Bloch propagation constant γ\gamma is defined as follows [1, 57]:

γ=1aarcosh⁡(1−ZseYsh2)=α+jβ(7)\begin{aligned} \gamma=\frac{1}{a}\operatorname{arcosh}\left(1-\frac{Z_{se}Y_{sh}}{2}\right) \\ &=\alpha+\mathrm{j}\beta \tag*{(7)} \end{aligned}

Here, the ZseZ_{se} and YshY_{sh} in TL model correspond to the B and C elements of the metamaterial unit's acoustic field transmission matrix, respectively. As depicted in Figure 4(a) and (Figure 4b), the leakage factor α\alpha and phase constant β\beta near the Γ\Gamma-point, as functions of frequency for the fabricated ADLWA, were determined using S-parameter retrieval from the driven N-cell configuration.

Propagation constants of the DLWA

Figure 4. The propagation constants of the DLWA are determined, with (a) the dispersion diagram extracted from the N-cell simulation illustrating a closed broadside stopband, and (b) the normalized attenuation (leakage) constant (α/k0\alpha/k_0) around broadside frequencies, which exhibits minimal variation. (c) The radiation beam angle varies as a function of the incident frequency. Solid curves represent the TL beam angles for 35 cells, while dotted lines indicate the simulated beam angles for the DLWA. (d) The aperture field and phase distribution along the length of the antenna are sampled at the center of the slots for broadside radiation.

The radiation region of the ADLWA is located above the sound line, represented by the black dashed line, indicating radiation in the fast-wave regime. The β=0\beta= 0 (zero-index) occurring at Γ\Gamma point, which is 1554 Hz (f0f_0), along with the non-zero group velocity, confirms the viability of broadside radiation. Figure 4(b) reveals that the leakage constant α/k0\alpha/k_0 is approximately 0.0267 at f0f_0 and remains stable, deviating from the usual patterns observed in LWA [1, 11, 12, 15]. Typically, LWAs exhibit pronounced fluctuations in the leakage constant around broadside due to phenomena such as open stopbands mechanisms [58]. When excitation occurs at frequencies within the left-handed (LH) region in TLs, between f1f_1 and f0f_0, negative group velocity results in backfire radiation. Conversely, forward radiation happens in the right-handed (RH) region, between f0f_0 and f2f_2. The Bloch parameters β\beta are employed to determine the radiation angle of the LWA. The main beam angles θ\theta at various frequencies are calculated using the finite element method (FEM) or Eq. (1) from TL theory. Figure 4(c) displays a comparison of the results obtained from these two methods for 35 cells. The frequency range presented is confined to the radiating band, spanning from f1=1490f_1 = 1490 Hz to f2=1955f_2 = 1955 Hz. The above shows the ADLWA lacks a stopband and seamlessly transitions from the backward to the forward region without any gap. Furthermore, the phase and magnitude functions of the radiation pattern for the N-celled array-type LWA are denoted as φn\varphi_n and PnP_n, respectively:

φn=−(n−1)k0a∗sin⁡θ(8)\varphi_n = -(n-1)k_0a * \sin\theta \tag*{(8)}
Pn=P0e−α(n−1)a(9)P_n = P_0e^{-\alpha(n-1)a} \tag*{(9)}

Where P0P_0 is the input pressure at the first unit cell element. The zero-index material (ZIM) behavior is characterized by a zero-phase progression along the length of the antenna, which results in broadside radiation when the antenna is excited unilaterally with minimal reflected waves. In Figure 4(d), the red solid line represents the phase distribution as calculated by Eq. (8). Meanwhile, the red dotted line is derived from simulation calculations of the field's phase, sampled at the center of the slots, for the frequency corresponding to the Γ\Gamma-point of the DLWA with 35 cells. The agreement between these two lines confirms the zero-phase propagation phenomenon. Additionally, the exponential decay of the field magnitude, depicted by the black solid line (TL model) and the black dashed line (simulation), further confirms the unilateral leaky operation characteristic of zero-index propagation.

Figure 5. (a) shows the working performance of ADLWA with different lengths. The radiation efficiency η\eta of the ADLWA showing a remarkable performance. What’s also interesting is that our radiation efficiency is around 70% throughout the entire back-to-forward scanning process. The efficiency of all previous acoustic leaky wave scanning antennas composed of membranes and acoustic cavities, whether uniformly arranged or specially designed with gradients, is less than 25%. Here, the radiation efficiency of our structure is more than twice that of previous acoustic leaky wave scanning antennas. Figure 5(b) demonstrates the DLWA's extensive scanning or steering capabilities. The sidelobe levels consistently stay well below the radiation power peak across all frequencies, reflecting its precise control over wave directionality. Figure 5(c-Figure 5e) presents the far-field radiation patterns (normalized power distribution) of the structure at three distinct frequencies: 1500 Hz, 1554 Hz, and 1600 Hz, corresponding to radiation in the backward, broadside, and forward directions, respectively. Additionally, we found that the DZIM offers us diverse modulation capabilities. Traditional acoustic waveguide leaky wave antennas are constrained by complex impedance matching issues, making them inflexible for adapting to

Working performance, scanning capability, and far-field radiation patterns of the ADLWA

Figure 5. (a) The working performance (transmission, reflection and radiation coefficient) of ADLWA with different lengths. (b) Scanning capability of the ADLWA accompanied by significantly low side lobes. The far-field radiation pattern of the ADLWA reveals backward radiation (c) at 1500 Hz, broadside radiation (d) at 1554 Hz, and forward radiation (e) at 1660 Hz

specific requirements in complex scenarios. Leveraging the super-coupling effect of DZIM, our ADLWA can be customized to achieve arbitrary radiation patterns by altering the antenna shape (as shown in the supplementary material). Furthermore, even when partial antenna elements are damaged, the overall super-coupling effect ensures stable operation of the antenna (as shown in Fig. S8 in the supplementary material).

We know that single sensor positioning has become a research focus in recent years. This intriguing approach could potentially disrupt traditional methods that depend on multi-sensor beamforming to pinpoint sound source locations. We have studied the ability of leaky wave antennas to steering sound waves in a frequency-dependent direction. According to the reciprocity principle, when operated in reverse, the antenna exhibits a well-defined frequency-direction relationship. In other words, ADLWA can be regarded as a passive sonar, which can detect the moving sound source in the space from the radiating side. As illustrated in Figure 6(a), a microphone is positioned at one end of the antenna within a designated yellow region. A point sound source Q, emitting at frequency ff, is located in the far field. The angles between the sound source and the antenna are denoted by θ\theta. It is critical to ensure that the distance from Q to the antenna is significantly greater than the shortest wavelength in the operational frequency band, allowing us to disregard any phase differences by the time the sound waves reach the microphone. The antenna captures the sound pressure spectrum as the angles between it and the sound source vary. During this process, the received sound pressure spectrum is expected to exhibit a peak at a specific direction. As depicted in Figure 6(b), the sound pressure spectra recorded at the microphone position for each incident angle reveal a lobe with maximal amplitude at a specific frequency. Using Eq. (1), the angle θ\theta can be determined, thereby confirming the direction of the sound source Q.

Schematic diagram for localizing the acoustic source and received sound pressure spectra

Figure 6. (a) The schematic diagram of the ADLWA for localizing the acoustic source. (b) Received sound pressure spectra captured by the microphone in the DLWA for various incident angles θ\theta.

Conclusion

In summary, we designed a novel double-zero refractive index metamaterial (DZIM) in air, utilizing a space-coiling structure, and successfully verified its zero-refractive-index properties. By integrating this metamaterial with a waveguide, we developed a highly efficient acoustic Dirac leaky-wave antenna (ADLWA) based on DZIMs, which enables continuous beam scanning from backward to forward radiation without a stopband. The ADLWA exhibits superior radiation efficiency and enhanced directivity compared to conventional leaky-wave antennas. The designed ADLWA serves a dual purpose, functioning as both a radiating antenna and a passive sonar system, offering promising prospects for the development of multifunctional, high-performance acoustic devices. This work lays a solid foundation for the further exploration of Dirac-like acoustic metamaterials in practical and adaptable applications.

Acknowledgement

The research reported in this manuscript was supported by King Abdullah University of Science and Technology Baseline Research Fund.

References

  1. [1]C. J. Naify, M. D. Guild, C. A. Rohde, D. C. Calvo, and G. J. Orris, Demonstration of a directional sonic prism in two dimensions using an air-acoustic leaky wave antenna, Appl. Phys. Lett. 107, 133505 (2015).DOI
  2. [2]A. Lai, C. Caloz, and T. Itoh, Composite right/left-handed transmission line metamaterials, IEEE Microw. Mag. 5, 34 (2004).DOI
  3. [3]S. Abielmona, H. V. Nguyen, and C. Caloz, Analog Direction of Arrival Estimation Using an Electronically-Scanned CRLH Leaky-Wave Antenna, IEEE Trans. Antennas Propag. 59, 1408 (2011).DOI
  4. [4]F. Bongard, H. Lissek, and J. R. Mosig, Acoustic transmission line metamaterial with negative/zero/positive refractive index, Phys. Rev. B 82, 094306 (2010).DOI
  5. [5]S. H. Lee, C. M. Park, Y. M. Seo, Z. G. Wang, and C. K. Kim, Acoustic metamaterial with negative density, Phys. Lett. A 373, 4464 (2009).DOI
  6. [6]Z. Yang, J. Mei, M. Yang, N. H. Chan, and P. Sheng, Membrane-Type Acoustic Metamaterial with Negative Dynamic Mass, Phys. Rev. Lett. 101, 204301 (2008).pubmed.ncbi.nlm.nih.gov/19113343
  7. [7]I. Felis-Enguix, J. Otero-Vega, M. Campo-Valera, I. Villó-Pérez, and J. L. Gómez-Tornero, Practical Aspects of Acoustic Leaky-Wave Antennas Applied to Underwater Direction Finding, Eng. Proc. 2, 1 (2020).
  8. [8]E. Romero-Vivas, J. Romero-Vivas, O. Bustamante, and B. Leon-Lopez, Educational open-source kit for the evaluation of acoustic leaky wave antennasa), J. Acoust. Soc. Am. 152, 1357 (2022).
  9. [9]C. W. Broadman, C. J. Naify, M. J. Lee, and M. R. Haberman, Design of a one-dimensional underwater acoustic leaky wave antenna using an elastic metamaterial waveguide, J. Appl. Phys. 129, 194902 (2021).DOI
  10. [10]C.J. Naify, M. R. Haberman, M. Guid, Acoustic leaky wave antennas: direction finding via-dispersion. Acoust. Today. 14.3 (2018)
  11. [11]C. J. Naify, C. N. Layman, T. P. Martin, M. Nicholas, D. C. Calvo, and G. J. Orris, Experimental realization of a variable index transmission line metamaterial as an acoustic leaky-wave antenna, Appl. Phys. Lett. 102, 203508 (2013).DOI
  12. [12]H. Esfahlani, S. Karkar, H. Lissek, and J. R. Mosig, Acoustic dispersive prism, Sci Rep 6, 18911 (2016).DOI
  13. [13]H. Esfahlani, S. Karkar, H. Lissek, and J. R. Mosig, Exploiting the leaky-wave properties of transmission-line metamaterials for single-microphone direction finding, J. Acoust. Soc. Am. 139, 3259 (2016).DOI
  14. [14]Q. Wang, J. Lan, Z. Deng, Y. Lai, and X. Liu, Acoustic source localization based on acoustic leaky-wave antenna with heterogeneous structure, J. Acoust. Soc. Am. 153, 487 (2023).DOI
  15. [15]J. Lan, X. Peng, X. Zhang, X. Liu, and Y. Li, Improving directional radiation quality based on a gradient amplitude acoustic leaky wave antenna, New J. Phys. 21, (2019).DOI
  16. [16]B. M. Goldsberry, C. W. Broadman, C. J. Naify, and M. R. Haberman, Exact radiation boundary conditions to determine the complex wave-number of an underwater acoustic leaky wave antenna, JASA Express Lett. 3, 035601 (2023).DOI
  17. [17]M. Lee, C. Wiederhold, K. Spratt, C. J. Naify, and M. R. Haberman, Experimental demonstration of an underwater acoustic leaky wave antenna, J. Acoust. Soc. Am. 145, 1727 (2019).
  18. [18]M. R. Haberman, K. Spratt, M. Lee, and C. J. Naify, Analysis of an underwater elastic leaky wave antenna, J. Acoust. Soc. Am. 146, 3044 (2019).DOI
  19. [19]V. C. Nguyen, L. Chen, and K. Halterman, Total transmission and total reflection by zero index metamaterials with defects, Phys Rev Lett 105, 233908 (2010).pubmed.ncbi.nlm.nih.gov/21231467
  20. [20]X. Huang, Y. Lai, Z. H. Hang, H. Zheng, and C. T. Chan, Dirac cones induced by accidental degeneracy in photonic crystals and zero-refractive-index materials, Nat Mater 10, 582 (2011).DOI
  21. [21]R. Liu, Q. Cheng, T. Hand, J. J. Mock, T. J. Cui, S. A. Cummer, and D. R. Smith, Experimental demonstration of electromagnetic tunneling through an epsilon-near-zero metamaterial at microwave frequencies, Phys Rev Lett 100, 023903 (2008).pubmed.ncbi.nlm.nih.gov/18232869
  22. [22]N. Engheta, Pursuing Near-Zero Response, Science 340, 286 (2013).DOI
  23. [23][23]F. Liu, Y. Lai, X. Huang, and C. T. Chan, Dirac cones at k=0 in phononic crystals, Phys. Rev. B 84, (2011).DOI
  24. [24][24]Y. Wu and J. Li, Total reflection and cloaking by zero index metamaterials loaded with rectangular dielectric defects, Appl. Phys. Lett. 102, 183105 (2013).DOI
  25. [25][25]M. Silveirinha and N. Engheta, Tunneling of Electromagnetic Energy through Subwavelength Channels and Bends using ε-Near-Zero Materials, Phys. Rev. Lett. 97, 157403 (2006).pubmed.ncbi.nlm.nih.gov/17155357
  26. [26][26]R. Fleury and A. Alù, Extraordinary sound transmission through density-near-zero ultranarrow channels, Phys Rev Lett 111, 055501 (2013).pubmed.ncbi.nlm.nih.gov/23952416
  27. [27][27]Y. Li, Y. Wu, and J. Mei, Double Dirac cones in phononic crystals, Appl. Phys. Lett. 105, (2014).DOI
  28. [28][28]R. Yang, X. Zhang, and G. Wang, A hybrid acoustic cloaking based on binary splitting metasurfaces and near-zero-index metamaterials, Appl. Phys. Lett. 120, (2022).DOI
  29. [29][29]H. Chu, Q. Li, B. Liu, J. Luo, S. Sun, Z. H. Hang, L. Zhou, and Y. Lai, A hybrid invisibility cloak based on integration of transparent metasurfaces and zero-index materials, Light Sci Appl 7, 50 (2018).DOI
  30. [30][30]L.-Y. Zheng, Y. Wu, X. Ni, Z.-G. Chen, M.-H. Lu, and Y.-F. Chen, Acoustic cloaking by a near-zero-index phononic crystal, Appl. Phys. Lett. 104, (2014).DOI
  31. [31][31]J. Hao, W. Yan, and M. Qiu, Super-reflection and cloaking based on zero index metamaterial, Appl. Phys. Lett. 96, 101109 (2010).DOI
  32. [32][32]I. Liberal and N. Engheta, Near-zero refractive index photonics, Nat. Photonics 11, 149 (2017).DOI
  33. [33][33]R. W. Ziolkowski, Propagation in and scattering from a matched metamaterial having a zero index of refraction, Phys. Rev. E 70, (2004).pubmed.ncbi.nlm.nih.gov/15600548
  34. [34][34]N. Xiang, Q. Cheng, J. Zhao, T. Jun Cui, H. Feng Ma, and W. Xiang Jiang, Switchable zero-index metamaterials by loading positive-intrinsic-negative diodes, Appl. Phys. Lett. 104, (2014).DOI
  35. [35][35]C. Ma, S. Gao, Y. Cheng, and X. Liu, Acoustic metamaterial antennas for combined highly directive-sensitive detection, Appl. Phys. Lett. 115, 053501 (2019).DOI
  36. [36][36]M. Marishwari, S. Madhavamoorthi, R. Meena, B. Asrafali, V. Subramanian, Z. Ouyang, and N. Yogesh, Directional, multi-beam, and compact wavefront transformers based on 3-D near-zero refractive index metamaterial, Opt. Contin. 2, 1093 (2023).DOI
  37. [37][37]Y. Liu et al., High-permittivity ceramics enabled highly homogeneous zero-index metamaterials for high-directivity antennas and beyond, eLight 4, 4 (2024).DOI
  38. [38][38]J. J. Park, K. J. B. Lee, O. B. Wright, M. K. Jung, and S. H. Lee, Giant Acoustic Concentration by Extraordinary Transmission in Zero-Mass Metamaterials, Phys. Rev. Lett. 110, 244302 (2013).pubmed.ncbi.nlm.nih.gov/25165929
  39. [39][39]H. Esfahlani, M. S. Byrne, M. McDermott, and A. Alù, Acoustic Supercoupling in a Zero-Compressibility Waveguide, Research 2019, (2019).
  40. [40][40]W. Wang, X. Fang, N. Wang, Y. Li, and T. Hao, Broadband acoustic double-zero-index cloaking with coupled Helmholtz resonators, New J. Phys. 24, 083032 (2022).DOI
  41. [41][41]C. M. Park and S. H. Lee, Propagation of acoustic waves in a metamaterial with a refractive index of near zero, Appl. Phys. Lett. 102, 241906 (2013).DOI
  42. [42][42]B. Edwards, A. Alu, M. E. Young, M. Silveirinha, and N. Engheta, Experimental verification of epsilon-near-zero metamaterial coupling and energy squeezing using a microwave waveguide, Phys Rev Lett 100, 033903 (2008).pubmed.ncbi.nlm.nih.gov/18232982
  43. [43][43]F. Liu, X. Huang, and C. T. Chan, Dirac cones at k→−0 in acoustic crystals and zero refractive index acoustic materials, Appl. Phys. Lett. 100, (2012).
  44. [44][44]M. Dubois, C. Shi, X. Zhu, Y. Wang, and X. Zhang, Observation of acoustic Dirac-like cone and double zero refractive index, Nat. Commun. 8, 14871 (2017).DOI
  45. [45][45]C. Xu, G. Ma, Z.-G. Chen, J. Luo, J. Shi, Y. Lai, and Y. Wu, Three-Dimensional Acoustic Double-Zero-Index Medium with a Fourfold Degenerate Dirac-like Point, Phys. Rev. Lett. 124, 074501 (2020).DOI
  46. [46][46]C. Xu, H. Chu, J. Luo, Z. H. Hang, Y. Wu, and Y. Lai, Three-Dimensional Electromagnetic Void Space, Phys. Rev. Lett. 127, 123902 (2021).
  47. [47][47]Y. Cheng, C. Zhou, B. G. Yuan, D. J. Wu, Q. Wei, and X. J. Liu, Ultra-sparse metasurface for high reflection of low-frequency sound based on artificial Mie resonances, Nat Mater 14, 1013 (2015).DOI
  48. [48][48]X. Zhu, B. Liang, W. Kan, Y. Peng, and J. Cheng, Deep-Subwavelength-Scale Directional Sensing Based on Highly Localized Dipolar Mie Resonances, Phys. Rev. Appl. 5, (2016).DOI
  49. [49][49]M. Landi, J. Zhao, W. E. Prather, Y. Wu, and L. Zhang, Acoustic Purcell Effect for Enhanced Emission, Phys Rev Lett 120, 114301 (2018).DOI
  50. [50][50]H. Long, S. Gao, Y. Cheng, and X. Liu, Multi-band quasi-perfect low-frequency sound absorber based on double-channel Mie resonator, Appl. Phys. Lett. 112, (2018).
  51. [51][51]J. Zhao, R. A. Jhandali, L. Zhang, and Y. Wu, Directional sound beam emission from a configurable compact multi-source system, Sci Rep 8, 1018 (2018).DOI
  52. [52][52]J. Zhao, L. Zhang, and Y. Wu, Enhancing monochromatic multipole emission by a subwavelength enclosure of degenerate Mie resonances, J Acoust Soc Am 142, EL24 (2017).DOI
  53. [53][53]J. Luo, Y. Yang, Z. Yao, W. Lu, B. Hou, Z. H. Hang, C. T. Chan, and Y. Lai, Ultratransparent Media and Transformation Optics with Shifted Spatial Dispersions, Phys. Rev. Lett. 117, 223901 (2016).pubmed.ncbi.nlm.nih.gov/27925741
  54. [54][54]C. Liu, J. Luo, and Y. Lai, Acoustic metamaterials with broadband and wide-angle impedance matching, Phys. Rev. Mater. 2, 045201 (2018).DOI
  55. [55][55]I. B. Vendik and O. G. Vendik, Metamaterials and their application in microwaves: A review, Tech. Phys. 58, 1 (2013).DOI
  56. [56][56]M. Memarian and G. V. Eleftheriades, Dirac leaky-wave antennas for continuous beam scanning from photonic crystals, Nat Commun 6, 5855 (2015).DOI
  57. [57][57]C. Caloz and T. Itoh, Electromagnetic Metamaterials: Transmission Line Theory and Microwave Applications (John Wiley & Sons, 2005).DOI
  58. [58][58]S. Paulotto, P. Baccarelli, F. Frezza, and D. R. Jackson, Full-Wave Modal Dispersion Analysis

Paper details

vlnc:W_hba4p6qh
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents