betaFeedback

WorksComputer Science

Analyzing Thermal Buckling in Curvilinearly Stiffened Composite Plates with Arbitrary Shaped Cutouts Using Isogeometric Level Set Method

Abstract

In this paper we develop a new simple and effective isogeometric analysis for modeling thermal buckling of stiffened laminated composite plates with cutouts using level sets. We employ a first order shear deformation theory to approximate the displacement field of the stiffeners and the plate. Numerical modeling with a treatment of trimmed objects, such as internal cutouts in terms of NURBS-based isogeometric analysis presents several challenges, primarily due to need for using the tensor product of the NURBS basis functions. Due to this feature, the refinement operations can only be performed globally on the domain and not locally around the cutout. The new approach can overcome the drawbacks in modeling complex geometries with multiple-patches as the level sets are used to describe the internal cutouts; while the numerical integration is used only inside the physical domain. Results of parametric studies are presented which show the influence of ply orientation, size and orientation of the cutout and the position and profile of the curvilinear stiffeners. The numerical examples show high reliability and efficiency of the present method compared with other published solutions and ABAQUS.

Introduction

Due to a large requirement of laminates for a variety of engineering applications, the use of plate structures with arbitrary cutouts are inevitable. The presence of cutouts can significantly affect the behaviors of structures. Studies on the analysis of eigenvalues and stability of laminates with cutouts are of great importance for many practical applications including airplane wing, fuselage and ribs.

In recent years, the isogeometric analysis (IGA) [1], [2] has become popular since it inherently owns many great advantages including exact geometry representation, higher-order continuity, simple mesh refinement, and avoiding the traditional mesh generation procedure. The traditional mesh generation in real world design problems could be complicated [3, 4, 5, 6, 4, 7, 8] Many insights into mathematical properties [9], [10], integration method [11], [12] and splines techniques [13] have been gained. The inherent characteristics of IGA make it superior to the classical FEM in many aspects [1]. The IGA has successfully applied to many engineering problems including plates and shells [14], [15], [16], [17] fluid mechanics [9], damage and fracture mechanics [18], contact mechanics [19], unsaturated flow problem in porous media [20], and structural shape optimization [21].

The higher-order smoothness of the NURBS basis functions have huge benefits with regards to the analysis of plates and shells. Based on the Kirchhoff plate theory, construction of rotation-free isogeometric shell was first proposed [22], and then developed for multiple NURBS patches by Kiendl [23]. Later, this element was extended for vibration and buckling analyses of laminated plates [24], functionally graded plates [15], bending and buckling analysis of laminated composite plates [17, 16, 25] and cloth simulation [19].

However, most of the problems investigated were simple single-patch geometry. In modeling a more complex geometry like a plate with a clover shaped internal cutout a trimmed NURBS surface can be useful. A NURBS surface and a set of ordered boundary curves lying within the parameter space of the surface [26] can be used to describe a trimmed NURBS surface. Shojaee et al. [24, 27] divided a rectangular plate with a heart shaped cutout into multiple NURBS patches, and to ensure continuity between adjacent patches, the authors applied the bending strip method. However this approach is quite cumbersome to implement and is also observed to complicate the unification of design and analysis, which is the sole aim of IGA. Trimmed NURBS surfaces were handled by Schmidt et al. [28] using a local reconstruction technique, which can handle trimmed NURBS surfaces under an isogeometric analysis framework. The method involved reconstructing trimmed NURBS patches using a least square approximation or by an interpolation method having known the trimming curves. The method is effective and can be easily applied to an arbitrarily shaped area on the surface. However, the method could not exactly describe trimmed boundaries and the number of sampling points heavily influenced the accuracy of the reconstructed boundaries. In order to model complex geometry problems, the IGA has been used in combination with an enrichment function similar to XFEM, to develop XIGA [29]. It has also been used in combination with the finite cell method (FCM) [30] and [31]. In this method, internal cutouts were described using level sets. However, level set methods using IGA were developed mostly for elastostatic problems, and are yet to be implemented for thermal buckling analysis of stiffened laminated plates with complicated internal cutouts. The objective of this research, is to fill this gap.

Thermal effects, especially thermal buckling is important to be considered in design, analysis and weight optimization of aircraft structures[32]and [33]. Such problems have been researched by many in the past. For instance, Noor and Burton [34, 35] and [36] used 3D elasticity to analyze the thermal buckling of multilayered and sandwich plates. However, it is difficult to solve problems which involve complicated geometry under different boundary conditions. The problem becomes even more challenging if the plate is reinforced with stiffeners.

Several authors in the past have studied the behavior of such stiffened plates. A finite element algorithm was developed by Mukhopadhyay and Mukherjee [37] to study the buckling of stiffened panels under uniaxial compression. Prusty and Satsangi [38] used the same algorithm to perform structural analysis of stiffened isotropic plates and shells. While the aforementioned authors studied straight stiffeners, curvilinearly stiffened panels were analyzed by Tamijani and Kapania [39], Zhao and Kapania [40], De and Kapania [4, 41, 42, 43] and Shi et al. [44]. It has been found by Hao et al. [45] that curvilinear stiffeners if used can improve the strength margins of panels since they reinforce the cutouts in them. The tension field resulting due to the presence of curvilinear stiffeners was examined and the loading path was compared with results obtained using straight stiffeners.

In this work, thermal buckling analysis of stiffened laminated composite plates with a cutout is presented. Level sets are used to describe the cutouts and numerical integration is used only inside the physical domain. The plate is assumed to be subjected to a uniform temperature rise for different boundary conditions. The stiffness matrices and thermal force vector are derived according to first-order shear deformation theory (FSDT). Firstly, the present formulation is verified by comparison with available references from literature. The significant effects of aspect ratio, length-to-thickness ratio, fiber orientation and boundary condition on the behavior of composite plates are then analyzed and useful conclusions are derived from the numerical results.

Mathematical foundations

Laminated composite panel

According to the first-order shear deformation theory (FSDT) the displacement field is considered as the first-order Taylor series expansion of the mid-plane displacement variables with respect to plate thickness as follows:

Consider a stiffened composite plate with a circular cutout as shown in Figure 1. The mid-plane of the panel OxyO_{xy} is used as the reference plane for the global coordinate system. The plate is assumed to have a uniform thickness with no plydrops. Let uu be the displacements in the xx-axis and vv be the in-plane displacements along the yy-axis. Let ww be the transverse deflection along the zz-axis.

Geometry and nomenclature of a stiffened composite panel with a central cutout

Figure 1. Geometry and nomenclature of a stiffened composite panel with a central cutout.

Let βy\beta_y and βx\beta_x be rotation components of the panel around the xx- and yy-axes, respectively. The displacement components of the panel can now be written as,

u(x,y,z,t)=u0(x,y,z,t)+zβx(x,y,t)v(x,y,z,t)=v0(x,y,z,t)+zβy(x,y,t)w(x,y,z,t)=w0(x,y,z,t)(1)\begin{aligned} u(x,y,z,t) &= u_0(x,y,z,t) + z\beta_x(x,y,t)\\ v(x,y,z,t) &= v_0(x,y,z,t) + z\beta_y(x,y,t)\\ w(x,y,z,t) &= w_0(x,y,z,t) \tag*{(1)} \end{aligned}

The plate strain energy UpU_p can be written as,

Up=12∬ΩεpLTDpεpLdΩ(2)U_p = \frac{1}{2}\iint_{\Omega} \boldsymbol{\varepsilon}_p^{\mathrm{L}T}\mathbf{D}_p\boldsymbol{\varepsilon}_p^{\mathrm{L}}\mathrm{d}\Omega \tag*{(2)}

Where, Dp\mathbf{D}_p depends on the material property, stacking sequence, ply orientation and thickness of the plate. Derivation of Dp\mathbf{D}_p is explained in Section 2.2. The generalized strains εpL\boldsymbol{\varepsilon}_p^{\mathrm{L}} can be expressed in terms of the generalized displacements up\mathbf{u}_p of the panel as,

εpL={εx0εy0γxy0κx0κy0κxy0γxz0γyz0}=[∂∂x00000∂∂x000∂∂x∂∂x000000∂∂x00000∂∂x000∂∂x∂∂x00∂∂x1000∂∂x01]{u0v0w0βxβy}=Bpup(3)\boldsymbol{\varepsilon}_p^{\mathrm{L}} = \left\{ \begin{array}{c} \varepsilon_x^0\\ \varepsilon_y^0\\ \gamma_{xy}^0\\ \kappa_x^0\\ \kappa_y^0\\ \kappa_{xy}^0\\ \gamma_{xz}^0\\ \gamma_{yz}^0 \end{array} \right\} = \left[ \begin{array}{ccccc} \frac{\partial}{\partial x} & 0 & 0 & 0 & 0\\ 0 & \frac{\partial}{\partial x} & 0 & 0 & 0\\ \frac{\partial}{\partial x} & \frac{\partial}{\partial x} & 0 & 0 & 0\\ 0 & 0 & 0 & \frac{\partial}{\partial x} & 0\\ 0 & 0 & 0 & 0 & \frac{\partial}{\partial x}\\ 0 & 0 & 0 & \frac{\partial}{\partial x} & \frac{\partial}{\partial x}\\ 0 & 0 & \frac{\partial}{\partial x} & 1 & 0\\ 0 & 0 & \frac{\partial}{\partial x} & 0 & 1 \end{array} \right] \left\{ \begin{array}{c} u_0\\ v_0\\ w_0\\ \beta_x\\ \beta_y \end{array} \right\} = \mathbf{B}_p\mathbf{u}_p \tag*{(3)}

The strain energy of the composite panel UpU_p is,

Up=12∬ΩupTBpTDpBpupdΩ(4)U_p = \frac{1}{2}\iint_{\Omega}\mathbf{u}_p^{T}\mathbf{B}_p^{T}\mathbf{D}_p\mathbf{B}_p\mathbf{u}_p\mathrm{d}\Omega \tag*{(4)}

For thermal bucking analysis, the geometric stiffness due to inplane stress resultants is considered. Thus, the potential WpW_p of the panel due to in-plane stress vector σp=(σx0  σy0  τxy0  0  0)\boldsymbol{\sigma}_p = (\sigma_x^0\ \ \sigma_y^0\ \ \tau_{xy}^0\ \ 0\ \ 0) is,

Wp=12∬ΩσpεpNLdΩ(5)W_p = \frac{1}{2}\iint_{\Omega}\boldsymbol{\sigma}_p\boldsymbol{\varepsilon}_p^{\mathrm{NL}}\mathrm{d}\Omega \tag*{(5)}

The nonlinear strain factor matrix is:

[BpNL]=[00∂∂x0000∂∂y00000∂∂x0000∂∂y00000∂∂x0000∂∂y](6)\left[B_{p}^{NL}\right] = \begin{bmatrix} 0 & 0 & \frac{\partial}{\partial x} & 0 & 0 \\ 0 & 0 & \frac{\partial}{\partial y} & 0 & 0 \\ 0 & 0 & 0 & \frac{\partial}{\partial x} & 0 \\ 0 & 0 & 0 & \frac{\partial}{\partial y} & 0 \\ 0 & 0 & 0 & 0 & \frac{\partial}{\partial x} \\ 0 & 0 & 0 & 0 & \frac{\partial}{\partial y} \end{bmatrix} \tag*{(6)}

The in-plane stress matrix can be written as:

σp=(ty0σy0txy00000txy0ty0σy0000000t312σy0t312σxy00000t312σxy0t312σy0000000t312σy0t312σxy00000t312σxy0t312σy0),(7)\boldsymbol{\sigma}_{p} = \begin{pmatrix} t_{y}^{0}\sigma_{y}^{0} & t_{xy}^{0} & 0 & 0 & 0 & 0 \\ t_{xy}^{0} & t_{y}^{0}\sigma_{y}^{0} & 0 & 0 & 0 & 0 \\ 0 & 0 & \frac{t^{3}}{12}\sigma_{y}^{0} & \frac{t^{3}}{12}\sigma_{xy}^{0} & 0 & 0 \\ 0 & 0 & \frac{t^{3}}{12}\sigma_{xy}^{0} & \frac{t^{3}}{12}\sigma_{y}^{0} & 0 & 0 \\ 0 & 0 & 0 & 0 & \frac{t^{3}}{12}\sigma_{y}^{0} & \frac{t^{3}}{12}\sigma_{xy}^{0} \\ 0 & 0 & 0 & 0 & \frac{t^{3}}{12}\sigma_{xy}^{0} & \frac{t^{3}}{12}\sigma_{y}^{0} \end{pmatrix}, \tag*{(7)}

Hence, (5) can be written as

Wp=12∬ΩupTBpNLTσpBpNLup dΩ(8)W_{p} = \frac{1}{2}\iint_{\Omega} \mathbf{u}_{p}^{T} B_{p}^{NL^{T}} \boldsymbol{\sigma}_{p} B_{p}^{NL} \mathbf{u}_{p}\,\mathrm{d}\Omega \tag*{(8)}

Orthotropic layers

The constitutive equation in the local coordinate system for the kthk^{th} orthotropic elastic lamina can be derived from Hooke's law as

{σ1σ2τ12σ3τ31τ23}(k)=[Q11Q120000Q21Q22000000Q66000Q31Q320Q33000000Q55000000Q44]{ε1−α1ΔTε2−α2ΔTγ12ε3−α3ΔTγ31γ23}(k)(9)\left\{ \begin{array}{c} \sigma_{1} \\ \sigma_{2} \\ \tau_{12} \\ \sigma_{3} \\ \tau_{31} \\ \tau_{23} \end{array} \right\}^{(k)} = \begin{bmatrix} Q_{11} & Q_{12} & 0 & 0 & 0 & 0 \\ Q_{21} & Q_{22} & 0 & 0 & 0 & 0 \\ 0 & 0 & Q_{66} & 0 & 0 & 0 \\ Q_{31} & Q_{32} & 0 & Q_{33} & 0 & 0 \\ 0 & 0 & 0 & 0 & Q_{55} & 0 \\ 0 & 0 & 0 & 0 & 0 & Q_{44} \end{bmatrix} \left\{ \begin{array}{c} \varepsilon_{1}-\alpha_{1}\Delta T \\ \varepsilon_{2}-\alpha_{2}\Delta T \\ \gamma_{12} \\ \varepsilon_{3}-\alpha_{3}\Delta T \\ \gamma_{31} \\ \gamma_{23} \end{array} \right\}^{(k)} \tag*{(9)}

where QijQ_{ij} are the elastic coefficients in the material coordinate system, TT is the temperature change and αi\alpha_{i} is the thermal coefficient of expansion in the principal ithi^{\text{th}}-direction. The transformed material constants are expressed as,

\begin{pmatrix} \overline{Q}_{11}\\ \overline{Q}_{12}\\ \overline{Q}_{22}\\ \overline{Q}_{16}\\ \overline{Q}_{26}\\ \overline{Q}_{66} \end{pmatrix} = \begin{bmatrix} c^{4} & 2c^{2}s^{2} & s^{4} & 4c^{2}s^{2}\\ c^{2}s^{2} & c^{4}+s^{4} & c^{2}s^{2} & -4c^{2}s^{2}\\ s^{4} & 2c^{2}s^{2} & c^{4} & 4c^{2}s^{2}\\ c^{3}s & cs(s^{2}-c^{2}) & -cs^{3} & 2cs(s^{2}-c^{2})\\ cs^{3} & cs(c^{2}-s^{2}) & -c^{3}s & 2cs(c^{2}-s^{2})\\ c^{2}s^{2} & -2c^{2}s^{2} & c^{2}s^{2} & (c^{2}-s^{2})^{2} \end{bmatrix} \begin{pmatrix} Q_{11}\\ Q_{12}\\ Q_{22}\\ Q_{66} \end{pmatrix}, \tag*{(10)}\end{pmatrix}
\begin{bmatrix} \overline{Q}_{44} & \overline{Q}_{13}\\ \overline{Q}_{45} & -\overline{Q}_{36}\\ \overline{Q}_{55} & \overline{Q}_{23} \end{bmatrix} = \begin{bmatrix} c^{2} & s^{2}\\ -cs & cs\\ s^{2} & c^{2} \end{bmatrix} \begin{bmatrix} Q_{44} & Q_{13}\\ Q_{55} & Q_{23} \end{bmatrix}, \quad\overline{Q}_{33}=Q_{33} \tag*{(11)}\end{bmatrix}
\begin{pmatrix} \alpha_x\\ \alpha_y\\ \alpha_{xy} \end{pmatrix} = \begin{bmatrix} c^{2} & s^{2}\\ s^{2} & c^{2}\\ 2cs & -2cs \end{bmatrix} \begin{pmatrix} \alpha_1\\ \alpha_2 \end{pmatrix}, \quad\alpha_z=\alpha_3 \tag*{(12)}\end{pmatrix}

where c=cos⁡θc=\cos\theta and s=sin⁡θs=\sin\theta.

Using this, Dp\mathbf{D}_p can now be written as

Dp=[AB0BD000As](13)\mathbf{D}_p= \begin{bmatrix} \mathbf{A} & \mathbf{B} & \mathbf{0}\\ \mathbf{B} & \mathbf{D} & \mathbf{0}\\ \mathbf{0} & \mathbf{0} & \mathbf{A}^{s} \end{bmatrix} \tag*{(13)}

where,

(Aij,Bij,Dij)=∫−h/2h/2Q‾ij(1,z,z2) dz,Aijs=K∫−h/2h/2Q‾ij dz(14)(A_{ij},B_{ij},D_{ij})=\int_{-h/2}^{h/2}\overline{Q}_{ij}(1,z,z^{2})\,\mathrm{d}z,\quad A^{s}_{ij}=K\int_{-h/2}^{h/2}\overline{Q}_{ij}\,\mathrm{d}z \tag*{(14)}

where AijA_{ij}, BijB_{ij} and DijD_{ij} are valid for i,j=1,2,6i,j=1,2,6, and AijsA^{s}_{ij} for i,j=4,5i,j=4,5 according to the Voigt notation. KK denotes the transverse shear correction coefficient. A value of K=5/6K=5/6 was used for the analyses.

Curvilinear stiffener

Consider a stiffener attached to a plate as shown in Figure 2.

Composite plate stiffened by a rectangular stiffener

Figure 2. Composite plate (red) stiffened by a rectangular stiffener (gray)

The width and height of the rectangular stiffener are given as bsb_s and hsh_s, respectively. Details of the coordinate system and nomenclature can be found in [40]. The stiffener is modeled using 1D 2nd2^{nd} order NURBS basis function. The stiffener is modeled as a Timoshenko beam. A detailed description of how displacement compatibility between the control points of the stiffener and the plate was achieved can be found in [46] and [47].

Isogeometric analysis

The concept of IGA is to use the same basis functions to generate CAD and to discretize the solution to the boundary value problem. This isoparametric formulation in combination with the properties of NURBS basis functions allows the geometry to be modeled exactly from the coarsest level of refinement, and maintains this exact representation as the mesh is refined. The elements are constructed by a knot span which is an array of non-decreasing sequence of parameter values [1]. The NURBS basis functions are used to construct the exact geometry, as well as the corresponding solution space. In this section, we present a primer on NURBS and also some basic formulations of IGA. Knot vectors can be defined as:

Ξ={ξ1,ξ2,…,ξn+p+1}(15)\Xi= \{\xi_1, \xi_2, \ldots, \xi_{n+p+1}\} \tag*{(15)}

B-spline basis functions are defined recursively starting with piecewise constants p=0p = 0

Ni0(ξ)={1if ξi<ξ<ξi+10otherwise(16)N_i^0(\xi) = \begin{cases} 1 & \text{if } \xi_i < \xi< \xi_{i+1} \\ 0 & \text{otherwise} \end{cases} \tag*{(16)}

For higher values like p=0,1,2…p = 0, 1, 2\ldots the basis functions are defined using a recursion relation

Nip(ξ)=ξ−ξiξi+p−ξiNip−1(ξ)+ξi+p+1−ξξi+p+1−ξi+1Ni+1p−1(ξ)(17)N_i^p(\xi) = \frac{\xi-\xi_i}{\xi_{i+p}-\xi_i}N_i^{p-1}(\xi) + \frac{\xi_{i+p+1}-\xi}{\xi_{i+p+1}-\xi_{i+1}}N_{i+1}^{p-1}(\xi) \tag*{(17)}

where ξ1\xi_1 is the ithi^{th} knot, nn is the number of basis functions and pp is the polynomial order.

We denote Non-uniform Rational B-splines (NURBS) functions expressed as

Ri,p(ξ)=Ni,p(ξ)wi∑j=1nNj,p(ξ)wj(18)R_{i,p}(\xi) = \frac{N_{i,p}(\xi)w_i}{\sum_{j=1}^{n}N_{j,p}(\xi)w_j} \tag*{(18)}

Where wiw_i is the weight corresponding to the ithi^{th} control point. For a 2-dimensional surface, the basis functions are expressed as:

Ri,jp,q(ξ,η)=Ni,p(ξ)Nj,q(η)wi,j∑i=1n∑j=1mNi,p(ξ)Nj,q(η)wi,j=Ni,p(ξ)Nj,q(η)wi,jW(ξ,η)(19)R_{i,j}^{p,q}(\xi,\eta) = \frac{N_{i,p}(\xi)N_{j,q}(\eta)w_{i,j}}{\sum_{i=1}^{n}\sum_{j=1}^{m}N_{i,p}(\xi)N_{j,q}(\eta)w_{i,j}} = \frac{N_{i,p}(\xi)N_{j,q}(\eta)w_{i,j}}{W(\xi,\eta)} \tag*{(19)}

The 2D surface is generated using the basis functions, Ri,jR_{i,j}, and the control points Pi,jP_{i,j}

S(ξ,η)=∑i=1n∑j=1mRi,jp,q(ξ,η)Pi,j(20)S(\xi,\eta) = \sum_{i=1}^{n}\sum_{j=1}^{m}R_{i,j}^{p,q}(\xi,\eta)P_{i,j} \tag*{(20)}

Further details can be found in [1] and [25].

Level Set Function

A signed distance function is utilized here to identify the enriched elements (elements cut by the cutout boundary), the outer elements (elements that are part of the plate) and inner elements (elements that fall completely within the cutout geometry) using the equation of a circle, given as:

ϕ(X)=∣X−Xc∣−r(21)\phi(\mathbf{X}) = \lvert\mathbf{X} - \mathbf{X}_c \rvert- r \tag*{(21)}

Where ϕ(X)\phi(\mathbf{X}) is the level set value at coordinates X\mathbf{X}. Xc\mathbf{X}_c is the coordinates of the center of the circular cutout and rr is the radius of the cutout. These values are stored at all control points for later use. Next, the coordinates of the points where the geometry of the cutout intersects the element is computed (Figure 3). This process will approximate the shape of the cutout as a polygon with sides equal to the number of enriched elements. This process has no impact on elements that are not cut by the interface.

Mappings and transformation from physical space to natural space

Figure 3. Mappings and transformation from physical space to natural space

The implemented enrichment function is:

ψ(X)=∑I=14∣ϕI∣N(X)I−∣∑I=14ϕIN(X)I∣(22)\psi(\mathbf{X}) = \sum_{I=1}^{4} \lvert\phi_I \rvert N(\mathbf{X})_I - \left\lvert\sum_{I=1}^{4} \phi_I N(\mathbf{X})_I \right\rvert \tag*{(22)}

The enrichment function ψ\psi at coordinates X\mathbf{X} is evaluated as a combination of control point level set values and the shape functions. Compared to other choices for enrichment functions this one has two major advantages. As the enrichment function has a zero value outside the cut elements as well as in the cut element control points there will be no contribution to the global stiffness matrix from an element that are not cut by the interface and the displacements evaluated at the control points will not have any extra contribution either.

Triangulation and Numerical Integration

Figure 3 shows a non enriched element (A) and an enriched element (B) in the x−yx-y coordinate system. Since some part of such enriched elements lie within the cutout, for numerical integration purposes, they have to be treated differently. For this, the coordinates of the points where the geometry of the cutout intersects the element is computed (Figure 3). The creation of additional points will enable the division of such a quadrilateral element into triangles and the process will approximate the shape of the cutout as a polygon with sides equal to the number of enriched elements

Consider one such triangular geometry (Δ1\Delta_1). Let the function f(x,y)f(x,y) determine some property at [x,y][x,y], a point within this geometry. Suppose another property, that is evaluated by the integration of f(x,y)f(x,y) over this geometry is of interest. An analytical calculation of the integrand is either impossible or very expensive. It is convenient to use Gauss quadrature formula that approximate the integral as a weighted sum of the function values at a number of predetermined points. Note that the Gauss integration computed using nn points is exact for a function of order 2n−12n-1 in 1D. These points are given in a transformed coordinate system (natural coordinate system). Thus, to integrate f(x,y)f(x,y) over Δ1\Delta_1,

I=∫Δ1f(x,y) dx dy(23)I = \int_{\Delta_1} f(x,y)\,dx\,dy \tag*{(23)}

a transformation into this natural coordinate system and a change of variables is necessary. This transformation is performed using a Jacobian matrix, Jel\mathbf{J}_{\mathrm{el}} and is defined by

[dxdy]=Jel[dξdη](24)\begin{bmatrix} dx \\ dy \end{bmatrix} = \mathbf{J}_{\mathrm{el}} \begin{bmatrix} d\xi\\ d\eta \tag*{(24)}\end{bmatrix}

Where,

Jel=[∂x∂ξ∂x∂η∂y∂ξ∂y∂η](25)\mathbf{J}_{\mathrm{el}} = \begin{bmatrix} \frac{\partial x}{\partial\xi} & \frac{\partial x}{\partial\eta} \\ \frac{\partial y}{\partial\xi} & \frac{\partial y}{\partial\eta} \end{bmatrix} \tag*{(25)}

Then it follows that

I=12∫01∫01−ηf(x(ξ,η),y(ξ,η))∣∣∂x∂ξ∂x∂η∂y∂ξ∂y∂η∣∣ dξdη(26)I = \frac{1}{2} \int_{0}^{1} \int_{0}^{1-\eta} f(x(\xi,\eta),y(\xi,\eta)) \left| \begin{vmatrix} \frac{\partial x}{\partial\xi} & \frac{\partial x}{\partial\eta} \\ \frac{\partial y}{\partial\xi} & \frac{\partial y}{\partial\eta} \end{vmatrix} \right| \,d\xi d\eta \tag*{(26)}

By numerical integration the quantity can be evaluated

I≅12∑1iwif(x(ξ,η),y(ξ,η))∣∣∂x∂ξ∂x∂η∂y∂ξ∂y∂η∣∣(27)I \cong\frac{1}{2} \sum_{1}^{i} w_i f(x(\xi,\eta),y(\xi,\eta)) \left| \begin{vmatrix} \frac{\partial x}{\partial\xi} & \frac{\partial x}{\partial\eta} \\ \frac{\partial y}{\partial\xi} & \frac{\partial y}{\partial\eta} \end{vmatrix} \right| \tag*{(27)}

Where ii is the number of Gauss points in the triangle. This will be useful in codes where element stiffness matrices for elements with enriched nodes are evaluated.

The element stiffness matrix will have a shape as follows:

Keij=∬elemBiTDBjt dxdy(28)\mathbf{K}_{e}^{ij} = \iint_{\mathit{elem}} \mathbf{B}_{i}^{\mathrm{T}}\mathbf{D}\mathbf{B}_{j}t\,\mathrm{d}x\mathrm{d}y \tag*{(28)}

Where,

Bi=[BSTD∣BENR](29)\mathbf{B}_{i} = [\mathbf{B}_{\mathrm{STD}} \mid\mathbf{B}_{\mathrm{ENR}}] \tag*{(29)}

Where Bi\mathbf{B}_{i} could be one of the three matrices, Bp\mathbf{B}_{p}, Bs\mathbf{B}_{s} or BNL\mathbf{B}_{\mathrm{NL}}. The subscripts STD\mathrm{STD} and ENR\mathrm{ENR} refer to standard non-enriched elements and enriched elements respectively. For a four noded isoparametric element the shape functions are defined in the isoparametric domain. However, the B matrices are functions of the shape functions which are defined in the isoparametric coordinate system ξ−η\xi-\eta (Figure 4), but the Gauss points and weights associated for a triangular domain aren’t.

Element and triangle transformed into coordinate system appropriate for B matrix calculation

Figure 4. Element and triangle transformed into coordinate system appropriate for BmatrixB_{\mathit{matrix}} calculation

They are defined in the ξ′−η′\xi^{\prime}-\eta^{\prime} coordinate system (Figure 5 with the vertices of the triangle located at:

Triangle transformed into coordinate system compatible with given Gauss-points: 3 Gauss points

(a) (a) 3 Gauss points

Triangle transformed into coordinate system compatible with given Gauss-points: 7 Gauss points

(b) (b) 7 Gauss points

Figure 5. Triangle transformed into coordinate system compatible with given Gauss-points

[ξ1′,η1′]=[0 0] ; [ξ2′,η2′]=[1 0] ; [ξ3′,η3′]=[0 1] ;(30)[\xi^{\prime}_{1},\eta^{\prime}_{1}] = [0\ 0]\ ;\ [\xi^{\prime}_{2},\eta^{\prime}_{2}] = [1\ 0]\ ;\ [\xi^{\prime}_{3},\eta^{\prime}_{3}] = [0\ 1]\ ; \tag*{(30)}

Hence, the mapping of these Gauss points to the isoparametric coordinate system is to be performed for each triangle.

These Gauss points can be mapped using nodal shape functions and isoparametric coordinates of vertices as follows:

[ξgpηgp]Δ1=[1−ξgp′−ηgp′ξgp′ηgp′]T[ξ1η1ξ2η2ξ3η3]Δ1(31)\left[\begin{array}{cc}\xi_{gp} & \eta_{gp}\end{array}\right]_{\Delta_1} = \left[\begin{array}{c} 1-\xi'_{gp}-\eta'_{gp}\\ \xi'_{gp}\\ \eta'_{gp} \end{array}\right]^{T} \left[\begin{array}{cc} \xi_1 & \eta_1\\ \xi_2 & \eta_2\\ \xi_3 & \eta_3 \end{array}\right]_{\Delta_1} \tag*{(31)}

The weight associated with each Gauss point will be scaled using the ratio of the areas of the triangles in the ξ\xi-η\eta coordinate system and the ξ′\xi'-η′\eta' coordinate system. We now have Gauss points and associated weights in the isoparametric coordinate system to in order to perform numerical integration.

Now, all the tools needed for the numerical integration are available. The stiffness matrix contribution from the triangle can be calculated now as

∬ΔBiT(x,y)DBj(x,y)t dx dy=12∑k=1nBi(x,y)TDBj(x,y)twk∣JΔ∣∣Jel∣(32)\iint_{\Delta} \mathbf{B}_i^{T}(x,y)\mathbf{D}\mathbf{B}_j(x,y)t\,dx\,dy = \frac{1}{2}\sum_{k=1}^{n}\mathbf{B}_i(x,y)^{T}\mathbf{D}\mathbf{B}_j(x,y)tw_k \lvert J_{\Delta}\rvert\lvert J_{\mathrm{el}}\rvert \tag*{(32)}

Where Bi\mathbf{B}_i and Bj\mathbf{B}_j are either BSTD\mathbf{B}_{\mathrm{STD}} or BENR\mathbf{B}_{\mathrm{ENR}}, depending on what part of the stiffness matrix are currently being calculated and nn is the number of Gauss points in the element. The target expression (a sample entry in a BSTD\mathbf{B}_{\mathrm{STD}} matrix) is,

N1,x=∂ξ∂x∂N1∂ξ+∂η∂x∂N1∂η(33)N_{1,x} = \frac{\partial\xi}{\partial x}\frac{\partial N_1}{\partial\xi} + \frac{\partial\eta}{\partial x}\frac{\partial N_1}{\partial\eta} \tag*{(33)}

Where NN is the basis function. While, for the enriched B-matrix BENR\mathbf{B}_{\mathrm{ENR}},

∂(ψN1)∂x=N1∂ψ∂x+∂N1∂xψ(34)\frac{\partial(\psi N_1)}{\partial x} = N_1\frac{\partial\psi}{\partial x} + \frac{\partial N_1}{\partial x}\psi \tag*{(34)}

Where, ψ\psi is the enrichment function.

A Three point parametrization of the curvilinear stiffener

Previous researchers [39], [40] and [44] modeled curvilinear stiffeners using a parabolic curve. Using the parametric equation of the parabola and the start and the end point coordinates, one can obtain the three control points which could define the Bezier curve [48]. Since any parabolic stiffener can be represented using three control points, the coordinates of the end control points Δϵ\Delta\epsilon and Point 2 (where δdist\delta_{\mathrm{dist}} refers to the point [δdist,δdist][\delta_{\mathrm{dist}},\delta_{\mathrm{dist}}]) were used to represent the curvilinear stiffener.

Results and Discussion

To demonstrate and validate the method, thermal buckling analysis of curvilinearly stiffened laminated composite plates with various cutouts is carried out. Results are compared with existing literature for some cases while for some others, using commercially popular software like ABAQUS. Parametric studies were performed which show the influence of both the cutout profile and the shape and position of the curvilinear stiffeners in the results.

Thermal buckling of laminated composite plates

Over the years, and most recently [49], several researchers have analyzed the thermal buckling of symmetric laminated plates. A four-layer [0∘/90∘/90∘/0∘][0^\circ/90^\circ/90^\circ/0^\circ] laminated plate with the two ratios of a/h=10a/h = 10 (Figure 2) and 100 were investigated for [50] two sets of boundary conditions. The plate is assumed to be a square of edge length 1 unit to make normalizations easy.

CCCC:u0=0,v0=0,ψx=0,ψy=0,w0=0(35)CCCC : u_0 = 0, v_0 = 0, \psi_x = 0, \psi_y = 0, w_0 = 0 \tag*{(35)}

on all four edges.

SSSS:u0=v0=w0=ϕy=ϕz=0on x=0,au0=v0=w0=ϕx=ϕz=0on y=0,b(36)\begin{aligned} SSSS:\quad&u_0=v_0=w_0=\phi_y=\phi_z=0 && \text{on } x=0,a\\ &u_0=v_0=w_0=\phi_x=\phi_z=0 && \text{on } y=0,b \tag*{(36)} \end{aligned}

Material properties are defined as [51], [50] and [49]

EL/ET=15, GLT/ET=0.5, GTT/ET=0.3356,νLT=0.3, νTT=0.49, αL/α0=0.015, αT/α0=1(37)E_L/E_T=15,\ G_{LT}/E_T=0.5,\ G_{TT}/E_T=0.3356, \qquad \nu_{LT}=0.3,\ \nu_{TT}=0.49,\ \alpha_L/\alpha_0=0.015,\ \alpha_T/\alpha_0=1 \tag*{(37)}

where LL and TT refer to the directions parallel and perpendicular to the fibers and α0\alpha_0 is the normalization factor for the thermal expansion coefficient. Table ?? illustrates the comparison of critical temperature obtained by NURBS-based IGA and FEM-Q16 [51], [50] and [49]. The critical buckling temperature values of the thinner plate have been scaled by 100.

Isotropic plate with a circular hole at the center

In order to illustrate the performance of IGA code while modeling plates with holes, an isotropic plate with a circular hole at the center was considered. Variation of the critical thermal load with respect to the radius of the hole was compared against Avci et al.[52]. The results were obtained for simply supported (SSSS) and clamped (CCCC) boundary conditions. The material properties of the plate are given as:

E=208 GPa, ν=0.3, α=1.17e−5 ∘C−1(38)E=208\ \mathit{GPa},\ \nu=0.3,\ \alpha=1.17\mathrm{e}{-5}\ ^\circ\mathrm{C}^{-1} \tag*{(38)}

As seen from the Table 1, the results are in good agreement with [52].

diameter widthCCCCSSSS
PresentAvciPresentAvci
029.3529.1610.8310.97
0.128.0128.5710.6410.82
0.229.1729.0710.5210.68
0.335.2735.3711.0111.14
0.449.5349.6712.4812.57
0.578.7478.5515.4115.34

Table 1. Variation of critical load with respect to radius of the circular cutout

Composite plate with elliptical cutout

To demonstrate the versatility and to validate the method, buckling analysis of plates with an elliptical cutout was considered (Figure 7). Results are compared with those obtained using ABAQUS. A unit square domain is considered with an elliptical cutout. The selected examples are for comparison purpose only and do not represent the full capabilities of the proposed method.

Dimensions and orientation of an elliptical cutout

Figure 7. Dimensions and orientation of an elliptical cutout

The ellipse is defined by the semi major axis, the semi minor axis and the angle of orientation θ\theta. For validation purposes, an ellipse of semi-major axis =0.2= 0.2, semi-minor axis =0.1= 0.1 and θ=0\theta= 0 was considered.

It can be observed from Table 2 that level set IGA approach yields relatively the same rate of convergence as ABAQUS. For mode shape comparison (Figure 8) purposes, a plate with an elliptical cutout (θ=45∘\theta= 45^{\circ}) was modeled in ABAQUS with an irregular mesh composed of 1028 elements. S8R: An 8-node doubly curved thick shell, reduced integration element was used to mesh the domain. IGA mode shape plot was obtained using 1024 elements.

Number of elementsABAQUSPresent
160.6360.653
640.4060.421
2560.37820.401
10240.3770.381

Table 2. The convergence of the critical thermal buckling load of a four-layer [0∘/90∘/90∘/0∘][0^\circ/90^\circ/90^\circ/0^\circ] laminated composite square plate.

Buckling mode shape plots of a plate with an elliptical cutout

Figure 8. Buckling mode shape plots of a plate with an elliptical cutout (θ=45∘\theta= 45^{\circ})

Next, the variation of critical buckling load with respect to change in eccentricity and angle of orientation of the cutout was analyzed. Table 3 presents the results for three different eccentricities. The results of the present method (LSM) are compared with those obtained using the Multi-Patch method (MPM)

θ\thetaSemi-minor axis=0.1 Semi-major axis=0.2Semi-minor axis=0.1 Semi-major axis=0.3Semi-minor axis=0.2 Semi-major axis=0.3
LSMMPMLSMMPMLSMMPM
00.3810.3790.4130.4020.6330.633
150.3950.3900.4430.4380.6590.653
300.4270.4210.5320.5250.7290.715
450.4690.4600.6410.6300.8090.807

Table 3. Variation of thermal buckling load of a four-layer [0°/90°/90°/0°] laminated composite square plate.

Curvilinearly stiffened composite panels with a noncentric circular cutout

In this sub section, the influence of the noncentric circular cutouts on clamped stiffened composite panels is studied. The stiffener is isotropic with Young’s modulus =ET= E_T, Poisson’s ratio =νLT= \nu_{LT} and coefficient of thermal expansion =α0= \alpha_0. The stiffness ratio γ=EI/bD\gamma= EI/bD and the area ratio δ=As/btp\delta= A_s/bt_p are 5 and 0.1 respectively unless specified. To check the robustness of the level set method, results for clamped curvilinearly stiffened composite plate are compared with those obtained using ABAQUS. A noncentric circular cutout of radius 0.15 with center at (0.3, 0.7) was assumed. The curvilinear stiffener configuration was adopted from [39] and scaled proportionally to match the dimensions of the plate. From the ABAQUS library, the plate was meshed using 3040 S8R elements and curvilinear stiffener was meshed using 192 elements S8R elements (48 divisions along the arc length and 4 divisions along the depth direction). The IGA plate model was meshed using 4096 elements and the curvilinear stiffener using 32 elements. The critical buckling temperature result was observed to converge for this mesh configuration. The first five eigen buckling models were extracted for each case. As seen from Figure 9 the buckling mode shapes obtained using IGA and ABAQUS are comparable.

Figure 9. First five eigenmode shape plots for a plate with curvilinear stiffener using LSM and ABAQUS, a commercial available software.

Curvilinearly stiffened composite panels with an elliptical central cutout

In this section, results of curvilinearly stiffened composite panels with elliptical cutouts are presented. An ellipse of semi-major axis =0.2= 0.2 and semi-minor axis =0.1= 0.1 is considered for all cases. The variation of the critical thermal load with respect to angle orientations, ply orientations, stiffness ratios and different stiffener profiles (defined by Δϵ\Delta\epsilon Figure 6) are presented in Table 5 and Table 6. The results obtained using present method (LSM) and the Multi-Patch method (MPM) are in excellent agreement.

Parametrization of curvilinear stiffener

Figure 6. Parametrization of curvilinear stiffener

Table 5: Variation of critical buckling load with respect to angle of orientation of the elliptical cutout for different ply orientations for γ=5\gamma= 5

Δϵ=0\Delta\epsilon= 0
θ\thetaAntisymmetric Cross-PlySymmetric Cross-PlySymmetric Angle-PlyAntisymmetric Angle-Ply
LSMMPMLSMMPMLSMMPMLSMMPM
00.4750.4730.4130.4060.4250.4230.4560.455
450.5070.4970.4940.4880.3700.3660.4360.434
Δϵ=0.25\Delta\epsilon= 0.25
00.5590.5530.4920.4810.4690.4620.5480.542
450.5980.5920.5950.5900.4060.3950.5250.521

Table 5. Variation of critical buckling load with respect to angle of orientation of the elliptical cutout for different ply orientations for γ=5\gamma= 5.

Table 6: Variation of critical buckling load with respect to the angle of orientation of the elliptical cutout for different ply orientations for γ=10\gamma= 10

Δϵ=0\Delta\epsilon= 0
θ\thetaAntisymmetric Cross-PlySymmetric Cross-PlySymmetric Angle-PlyAntisymmetric Angle-Ply
LSMMPMLSMMPMLSMMPMLSMMPM
00.4880.4850.4170.4090.4430.4430.4690.468
450.5090.5090.5020.4950.830.3780.4480.449
Δϵ=0.25\Delta\epsilon= 0.25
00.5900.5810.5090.5010.4850.4790.5760.572
450.6190.6120.6180.6100.4100.4050.5600.554

Table 6. Variation of critical buckling load with respect to the angle of orientation of the elliptical cutout for different ply orientations for γ=10\gamma= 10.

Curvilinearly stiffened composite panels with a complicated cutout

The present method is applied to analyze a stiffened laminated composite plate with a clover shaped cutout Figure 10. The cutout is a boolean of three circles of radius 0.15 resulting in a clover shape. The center of circles A, B and C are at (0.4, 0.65), (0.5, 0.7) and (0.5, 0.6) respectively. Figure 10 shows the mesh plot for the plate geometry with the red region being the enriched elements.

Isogeometric mesh plot of a plate with clover shaped cutout

Figure 10. Isogeometric mesh plot of a plate with clover shaped cutout constructed with three circles. The enriched elements are shown in red

To check the accuracy of the level set algorithm, results for clamped curvilinearly stiffened composite plate with a clover shaped cutout are compared with those obtained using ABAQUS. The curvilinear stiffener configuration was adopted from [39] and scaled proportionally to match the dimensions of the plate. From the ABAQUS library, the plate was meshed using 3040 S8R elements and curvilinear stiffener was meshed using 192 elements S8R elements (48 divisions along the arc length and 4 divisions along the depth direction). The IGA plate model was meshed using 4096 elements and the curvilinear stiffener using 32 elements. The first five eigen buckling models were extracted for each case. The buckling mode shapes obtained using the IGA approach are similar to those obtained using ABAQUS as can be seen from Figure 11.

Figure 11. First five eigenmode shape plots for a plate with curvilinear stiffener using a LSM and ABAQUS, a commercial available software.

ModePresent ΔTcr\Delta T_{cr}ABAQUS ΔTcr\Delta T_{cr}
10.7510.748
20.8270.817
30.9610.955
41.0091
51.0961.085

Table 11.

Advantages and limitations

One of the advantages of the level set method is their ability to use the same mesh controls on the plate for different types of cutouts. Figure 12 shows how the plate is discretized using 16×1616 \times16 elements for circular as well as elliptical cutouts.

Identical IGA mesh for circular and elliptical cutouts

Figure 12. (a) circular (b) angled elliptical. Identical IGA mesh for circular and elliptical cutouts

Discussions in § 2.6 describe the creation of additional degrees of freedom while implementing the level set method. Table 8 shows the number of additional degrees of freedom created for each levels of refinement for a plate with a cutout of radius 0.15. It can be observed that the total degrees of freedom (nDoF = Total number of Gauss points ×\times 5) increase much steeply than the additional degrees of freedom (Extra DoF) with increase in refinement levels.

RefinementnDoFExtra DoF
3660160
41920300
56320540

Table 8. Additional degrees of freedom with respect to an increase in refinement

Next, computational cost due to these additional degrees of freedom was analyzed. Two cases were considered, a stiffened plate without any cutout (Case 1) and a stiffened plate with a central circular cutout of radius 0.15. The material properties, ply orientation and stiffener profile were the same as mentioned in § 3.4. The computational time (in seconds) to perform the static and the eigenvalue analyses are compared for each case (Table 9, Figure 14 and Figure 13). It is observed that the additional degrees of freedom have a much higher influence on the results from a static analysis as compared to the buckling analysis. However, the difference is very little for lower levels of refinement.

Refinement445566
StaticEigenvalueStaticEigenvalueStaticEigenvalue
Case 10.03420.20450.20080.70871.27224.3813
Case 20.05040.22440.20140.87244.51324.5352

Table 9. Computational time (in seconds) with respect to refinement for static and eigenvalue analyses

Variation in computational time for eigenvalue analysis

Figure 13. Variation in computational time (in seconds) with respect to refinement for eigenvalue analysis

Variation in computational time in seconds with respect to refinement for static analysis; plot labels: Refinement, Time in seconds, Simple plate, Plate with a cutout

Figure 14. Variation in computational time (in seconds) with respect to refinement for static analysis

Convergence studies

Convergence studies on a stiffened plate with a cutout are not as straightforward as a simple plate problem since the size of the cutout, size of the stiffener and the plate meshes all affect the results. We consider a stiffened plate with a central circular cutout. The material properties, ply orientation and stiffener profile were the same as mentioned in § 3.4. For convergence studies with respect to the increasing cutout size, an unstiffened plate was considered. It can be observed from Figure 15 that the rate of convergence becomes slower with an increase in the cutout radius.

Line plot showing variation of critical buckling load with refinement for cutouts of radii 0.1, 0.15, 0.2 and 0.25

Figure 15. Variation of critical buckling load with respect to various plate mesh sizes for cutouts of increasing radii

Figures 16, 17 and 18 present the change of critical buckling loads with respect to various stiffener and plate mesh sizes for cutouts of varying radii. It is observed that for cutouts with relatively smaller radius (0.15 and 0.2), for each refinement levels of the plate mesh, the results converge for the 4th4^{th} order of refinement of the stiffener mesh. It is also observed that the plate mesh density has a higher influence on the results compared to the stiffener mesh density. However, as the radius of the cutout is increased to 0.25, the stiffener mesh density starts to impact the convergence of results to a much higher degree (Figure 16).

Variation of critical buckling load with respect to various stiffener and plate mesh sizes for radius = 0.25

Figure 16. Variation of critical buckling load with respect to various stiffener and plate mesh sizes for radius = 0.25

Variation of critical buckling load with respect to various stiffener and plate mesh sizes for radius = 0.2

Figure 17. Variation of critical buckling load with respect to various stiffener and plate mesh sizes for radius = 0.2

Variation of critical buckling load with respect to various stiffener and plate mesh sizes

Figure 18. Variation of critical buckling load with respect to various stiffener and plate mesh sizes for radius=0.15radius = 0.15

Conclusions

This paper discusses the level set method which requires very little computational effort to obtain a mesh independent description of the geometrical shape of a complicated cutout. The level sets discussed in this paper are implemented in the form of a signed distance function which is both computationally inexpensive and easy to implement. Such an implementation is greatly useful since the tensor product nature of the NURBS basis functions only allows for global refinement and therefore treating the trimmed objects such as internal cutouts is rather difficult. However, implementing the level set method obviates the use of trimmed NURBS surface to describe complex geometrical features like the cutouts. The efficiency of this method for thermal buckling analysis is described with the help of numerical examples for stiffened laminated plates containing complicated cutouts of various shapes and dimensions.

Acknowledgement

The authors would like to thank the Institute for Critical Technology and Applied Science (ICTAS) at Virginia Tech for providing financial support which made this research possible.

References

  1. [1]T. J. Hughes, J. A. Cottrell, Y. Bazilevs, Isogeometric analysis: CAD, finite elements, NURBS, exact geometry and mesh refinement, Computer Methods in Applied Mechanics and Engineering 194 (39-41) (2005) 4135–4195.DOI
  2. [2]T. T. Yu, S. Yin, T. Q. Bui, S. Hirose, A simple FSDT-based isogeometric analysis for geometrically nonlinear analysis of functionally graded plates, Finite Elements in Analysis and Design 96 (C) (2015) 1–10.DOI
  3. [3]S. De, K. Singh, B. Alanbay, R. K. Kapania, R. Aguero, Structural optimization of truck front-frame under multiple load cases, in: ASME International Mechanical Engineering Congress and Exposition, Vol. 52187, American Society of Mechanical Engineers, 2018, p. V013T05A039.DOI
  4. [4]S. De, K. Singh, J. Seo, R. K. Kapania, E. Ostergaard, N. Angelini, R. Aguero, Structural design and optimization of commercial vehicles chassis under multiple load cases and constraints, in: AIAA Scitech 2019 Forum, 2019, p. 0705.DOI
  5. [5]S. De, K. Singh, J. Seo, R. K. Kapania, E. Ostergaard, N. Angelini, R. Aguero, Lightweight chassis design of hybrid trucks considering multiple road conditions and constraints, World Electric Vehicle Journal 12 (1) (2021) 3.DOI
  6. [6]S. De, K. Singh, J. Seo, R. K. Kapania, R. Aguero, E. Ostergaard, N. Angelini, Unconventional truck chassis design with multi-functional cross members, Tech. rep., SAE Technical Paper (2019).DOI
  7. [7]M. Jrad, S. De, R. K. Kapania, Global-local aeroelastic optimization of internal structure of transport aircraft wing, in: 18th AIAA/ISSMO Multidisciplinary Analysis and Optimization Conference, 2017, p. 4321.DOI
  8. [8]S. De, R. K. Kapania, Algorithms for 2d mesh decomposition in distributed design optimization (2021). arXiv:2002.00525.arxiv.org/abs/2002.00525
  9. [9]Y. Bazilevs, V. M. Calo, T. J. R. Hughes, Y. Zhang, Isogeometric fluid-structure interaction: theory, algorithms, and computations, Computational Mechanics 43 (1) (2008) 3–37.DOI
  10. [10]J. A. Evans, Y. Bazilevs, I. Babuška, T. J. Hughes, n-Widths, sup-infs, and optimality ratios for the κ-version of the isogeometric finite element method, Computer Methods in Applied Mechanics and Engineering 198 (21-26) (2009) 1726–1741.
  11. [11]T. J. R. Hughes, A. Reali, G. Sangalli, Efficient quadrature for NURBS-based isogeometric analysis, Computer Methods in Applied Mechanics and Engineering 199 (5-8) (2010) 301–313.
  12. [12]F. Auricchio, F. Calabrò, T. J. Hughes, A. Reali, G. Sangalli, A simple algorithm for obtaining nearly optimal quadrature rules for NURBS-based isogeometric analysis, Computer Methods in Applied Mechanics and Engineering 249-252 (2012) 15–27.DOI
  13. [13]Y. Bazilevs, C. Michler, V. M. Calo, T. J. Hughes, Isogeometric variational multiscale modeling of wall-bounded turbulent flows with weakly enforced boundary conditions on unstretched meshes, Computer Methods in Applied Mechanics and Engineering 199 (13-16) (2010) 780–790.
  14. [14]N. Valizadeh, T. Bui, V. Vu, H. Thai, M. Nguyen, Isogeometric Simulation for Buckling, Free and Forced Vibration of Orthotropic Plates, International Journal of Applied Mechanics 05 (02) (2013) 1350017.DOI
  15. [15]S. Yin, J. S. Hale, T. Yu, T. Q. Bui, S. P. Bordas, Isogeometric locking-free plate element: A simple first order shear deformation theory for functionally graded plates, Composite Structures 118 (1) (2014) 121–138.DOI
  16. [16]H. Kapoor, R. K. Kapania, S. R. Soni, Interlaminar stress calculation in composite and sandwich plates in NURBS Isogeometric finite element analysis, Composite Structures 106 (2013) 537–548.DOI
  17. [17]H. Kapoor, R. K. Kapania, Geometrically nonlinear NURBS isogeometric finite element analysis of laminated composite plates, Composite Structures 94 (12) (2012) 3434–3447.DOI
  18. [18]C. V. Verhoosel, M. A. Scott, T. J. R. Hughes, R. de Borst, An isogeometric analysis approach to gradient damage models, International Journal for Numerical Methods in Engineering 86 (1) (2011) 115–134. arXiv:1010.1724.
  19. [19]J. Lu, Isogeometric contact analysis: Geometric basis and formulation for frictionless contact, Computer Methods in Applied Mechanics and Engineering 200 (5-8) (2011) 726–741.DOI
  20. [20]H. Nguyen-Xuan, L. V. Tran, C. H. Thai, S. Kulasegaram, S. P. Bordas, Isogeometric analysis of functionally graded plates using a refined plate theory, Composites Part B: Engineering 64 (2014) 222–234.
  21. [21]W. A. Wall, M. A. Frenzel, C. Cyron, Isogeometric structural shape optimization, Computer Methods in Applied Mechanics and Engineering 197 (33-40) (2008) 2976–2988.DOI
  22. [22]J. Kiendl, K.-U. Bletzinger, J. Linhard, R. Wüchner, Isogeometric shell analysis with Kirchhoff–Love elements, Computer Methods in Applied Mechanics and Engineering 198 (49-52) (2009) 3902–3914.DOI
  23. [23]J. Kiendl, Y. Bazilevs, M. C. Hsu, R. Wüchner, K. U. Bletzinger, The bending strip method for isogeometric analysis of Kirchhoff–Love shell structures comprised of multiple patches, Computer Methods in Applied Mechanics and Engineering 199 (37-40) (2010) 2403–2416.DOI
  24. [24]S. Shojaee, E. Izadpanah, N. Valizadeh, J. Kiendl, Free vibration analysis of thin plates by using a NURBS-based isogeometric approach, Finite Elements in Analysis and Design 61 (2012) 23–34.DOI
  25. [25]L. V. Tran, C. H. Thai, H. T. Le, B. S. Gan, J. Lee, H. Nguyen-Xuan, Isogeometric analysis of laminated composite plates based on a four-variable refined plate theory, Engineering Analysis with Boundary Elements 47 (2014) 68–81.DOI
  26. [26]L. A. Piegl, W. Tiller, Geometry-based triangulation of trimmed NURBS surfaces, Computer-Aided Design 30 (1) (1998) 11–18.DOI
  27. [27]S. Shojaee, N. Valizadeh, E. Izadpanah, T. Bui, T. V. Vu, Free vibration and buckling analysis of laminated composite plates using the NURBS-based isogeometric finite element method, Composite Structures 94 (5) (2012) 1677–1693.DOI
  28. [28]R. Schmidt, R. Wüchner, K. U. Bletzinger, Isogeometric analysis of trimmed NURBS geometries, Computer Methods in Applied Mechanics and Engineering 241-244 (2012) 93–111.
  29. [29]S. S. Ghorashi, N. Valizadeh, S. Mohammadi, Extended isogeometric analysis for simulation of stationary and propagating cracks, International Journal for Numerical Methods in Engineering 89 (9) (2012) 1069–1101. arXiv:1010.1724.
  30. [30]E. Rank, M. Ruess, S. Kollmannsberger, D. Schillinger, A. Düster, Geometric modeling, isogeometric analysis and the finite cell method, Computer Methods in Applied Mechanics and Engineering 249-252 (2012) 104–115.DOI
  31. [31]D. Schillinger, L. Dedè, M. A. Scott, J. A. Evans, M. J. Borden, E. Rank, T. J. Hughes, An isogeometric design-through-analysis methodology based on adaptive hierarchical refinement of NURBS, immersed boundary methods, and T-spline CAD surfaces, Computer Methods in Applied Mechanics and Engineering 249-252 (2012) 116–150.
  32. [32]B. Devarajan, D. Locatelli, R. Kapania, R. Meritt, Thermomechanical analysis and design of threaded fasteners, in: 2016 AIAA/ASCE/AHS/ASC Structures, Structural Dynamics, and Materials Conference, 2016, p. 0579.DOI
  33. [33]Q. Li, B. Devarajan, X. Zhang, R. Burgos, D. Boroyevich, P. Raj, Conceptual design and weight optimization of aircraft power systems with high-peak pulsed power loads, in: SAE Technical Paper, SAE International, 2016, p. 10. doi:10.4271/2016-01-1986.
  34. [34]A. K. Noor, W. S. Burton, C. W. Bert, Computational Models for Sandwich Panels and Shells, Applied Mechanics Reviews 49 (3) (1996) 155.DOI
  35. [35]W. S. Burton, A. K. Noor, Three Dimensional Solutions for Thermomechanical Stresses in Sandwich Panels and Shells, Journal of Engineering Mechanics 120 (10) (1994) 2044–2071.
  36. [36]A. K. Noor, W. S. Burton, Three Dimensional Solutions for Thermal Buckling of Multilayered Anisotropic Plates, Journal of Engineering Mechanics 118 (4) (1992) 683–701.DOI
  37. [37]M. Mukhopadhyay, A. Mukherjee, Finite element buckling analysis of stiffened plates, Computers & structures 34 (6) (1990) 795–803.DOI
  38. [38]B. G. Prusty, S. Satsangi, Finite element transient dynamic analysis of laminated stiffened shells, Journal of Sound and Vibration 248 (2) (2001) 215–233.DOI
  39. [39]A. Y. Tamijani, R. K. Kapania, Buckling and Static Analysis of Curvilinearly Stiffened Plates Using Mesh-Free Method, AIAA Journal 48 (12) (2010) 2739–2751.DOI
  40. [40]W. Zhao, R. K. Kapania, Buckling analysis of unitized curvilinearly stiffened composite panels, Composite Structures 135 (2016) 365–382.DOI
  41. [41]J. H. Robinson, S. Doyle, G. Ogawa, M. Baker, S. De, M. Jrad, R. K. Kapania, Aeroelastic optimization of wing structure using curvilinear spars and ribs (sparibs), in: 17th AIAA/ISSMO Multidisciplinary Analysis and Optimization Conference, 2016, p. 3994.DOI
  42. [42]S. De, M. Jrad, D. Locatelli, R. K. Kapania, M. Baker, Sparibs geometry parameterization for wings with multiple sections using single design space, in: 58th AIAA/ASCE/AHS/ASC Structures, Structural Dynamics, and Materials Conference, 2017, p. 0570.DOI
  43. [43]S. De, Structural modeling and optimization of aircraft wings having curvilinear spars and ribs (sparibs), Ph.D. thesis, Virginia Tech (2017).
  44. [44]P. Shi, R. K. Kapania, C. Y. Dong, Vibration and Buckling Analysis of Curvilinearly Stiffened Plates Using Finite Element Method, AIAA Journal 53 (5) (2015) 1319–1335.DOI
  45. [45]P. Hao, B. Wang, K. Tian, G. Li, X. Zhang, Optimization of curvilinearly stiffened panels with single cutout concerning the collapse load, International Journal of Structural Stability and Dynamics 16 (07) (2016) 1550036.DOI
  46. [46]B. Devarajan, R. K. Kapania, Thermal buckling of curvilinearly stiffened laminated composite plates with cutouts using isogeometric analysis, Composite Structures (2020) 111881.DOI
  47. [47]B. Devarajan, Thermomechanical and Vibration Analysis of Stiffened Unitized Structures and Threaded Fasteners, vtechworks.lib.vt.edu, 2019.
  48. [48]L. L. Piegl, W. Tiller, The NURBS Book, Vol. 28, Springer Science & Business Media, 1996. arXiv:arXiv:1011.1669v3.
  49. [49]L. V. Tran, M. A. Wahab, S. E. Kim, An isogeometric finite element approach for thermal bending and buckling analyses of laminated composite plates, Composite Structures 179 (2017) 35–49.DOI
  50. [50]C. Sarath Babu, T. Kant, Refined higher order finite element models for thermal buckling of laminated composite and sandwich plates, Journal of Thermal Stresses 23 (2) (2000) 111–130.DOI
  51. [51]T. Kant, C. S. Babu, Thermal buckling analysis of skew fibre-reinforced composite and sandwich plates using shear deformable finite element models, Composite Structures 49 (1) (2000) 77–85.DOI
  52. [52]A. Avci, S. Kaya, B. Daghan, Thermal buckling of rectangular laminated plates with a hole, Journal of Reinforced Plastics and Composites 24 (3) (2005) 259–272.DOI

Paper details

vlnc:W_hc585rmg
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 10

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Computer Science

Not recorded for this paper

View statement
Looking for related papers…
Contents