betaFeedback

WorksPhysics and Astronomy

DFT insights into the new Hf-based chalcogenide MAX phase Hf2SeC

Abstract

The physical characteristics of the novel chalcogenide MAX phase Hf2SeC have been investigated using the DFT method. The obtained lattice constant and elastic constants (Cij) are compared with previous results to check the consistency of our setting parameters during calculations Moreover, the elastic properties such as elastic constants, moduli, anisotropy, and hardness are also compared with preexisting MAX phases of its kind. The checking of mechanical stability has been done based on Cij in accordance with the previously stated stability criteria. The reason for the higher hardness of Hf2SeC compared to Hf2SC is explained using the density of states (DOS). The brittleness character of Hf2SeC has been revealed using the Pugh ratio, Poisson ratio, and Cauchy pressure. The electronic properties (band structure and charge density mapping) of Hf2SeC are studied to disclose the metallic nature as well as bonding nature within the titled chalcogenide. The anisotropy in both electronic conductivity and mechanical properties is investigated. The temperature and pressure dependence of volume, Grüneisen parameter, Debye temperature, thermal expansion coefficient (TEC), and specific heat at constant volume (Cv) are explored. In addition, minimum thermal conductivity (Kmin) and melting point (Tm) are studied to explore its suitability for high-temperature applications.

Introduction

Recently, chalcogenide MAX phase members have been extended by the synthesis of two new chalcogens (Se) containing MAX phase: M2SeC\mathrm{M}_{2}\mathrm{SeC} (M = Hf, Zr) [1] [2]. The scientific community is trying to expand the family member of MAX phase materials for a long time, motivated by their peculiar properties, as a result, more than 150 MAX phases have already been revealed [3]. To do this, scientists have focused on the tuning of the compositions and structure to accomplish superior properties. The recent attempts reported so far as new compounds [1] [2, 4, 5, 6, 7, 8, 9, 10, 11] solid solutions [14, 15, 16, 17, 18, 19, 20, 21] [12, 13]. Some other MAX phases have also been reported with slightly different structures: M2A2XM_2A_2X [22, 23, 24] and M3A2XM_3A_2X [25], rare-earth i-MAX phases [26, 27], 212 MAX phases [28, 29, 30, 31], 314 MAX phases [28, 32, 33]. The most recent extension of X element up to B has also been reported as MAX phase borides [34, 35] [5, 6, 36, 37, 38, 39].

Now, the question is what aspect of the MAX phase triggers the scientists. The prime feature of the MAX phase that attracts mainly is the unification of metallic and ceramics properties. Again, the question is how it is possible to combine both characteristics. The answer lies within the structure of the MAX compounds in which there are M-A bonds responsible for metallic character and covalent M-X bonds that contribute to the ceramics character [40,41]; consequently, the conductivity (electrical and thermal), the strength of mechanical character, machinability are like metals, and the high-temperature mechanical parameters are good, corrosion and oxidation resistance also good as like as ceramics materials [42] which are exhibited by the MAX phases. Owing to the aforesaid characteristics, their potential applications include a very long list that can be found elsewhere [21] [3, 42, 43, 44].

The S containing MAX phases [M2SCM_2SC (M=TiM=\mathrm{Ti}, Zr, Hf, Nb)] have been studied both experimentally and theoretically [35] [5, 6, 45, 46, 47, 48, 49, 50]. Bouhemadou et al [45] studied the elastic and electronic properties of M2SCM_2SC (M=TiM=\mathrm{Ti}, Zr, Hf) phases. Superconducting phase Nb2SCNb_2SC has been reported by Shein et al [46]. A comprehensive survey of elastic properties of the M2AXM_2AX phase was carried out by Cover et al [50] where S containing phases were included. Zr2SCZr_2SC MAX compound was investigated by Feng et al in which the elastic and electronic properties were considered. Nasir et al [48,49] have selected Zr and Nb-based S containing phases for their DFT-based study. S-based MAX phase borides were synthesized by Rackl et al [5,6] which were further investigated [35]. To our knowledge, only the Zr2SeCZr_2SeC compound is studied experimentally [1] and theoretically [51]. Wang et al [2] synthesized Hf2SeCHf_2SeC and studied its thermal expansion coefficient and stiffness constants (CijC_{ij}) only. The obtained results were compared with those of Hf2SCHf_2SC, Zr2SeCZr_2SeC, and Zr2SCZr_2SC, Ti2SCTi_2SC MAX phases where available. This too little information is not adequate to disclose the potential of Hf2SeCHf_2SeC for industrial use in various areas, in place of other MAX phases that are already been used. For example, the mechanical behavior exploring parameters such as elastic moduli, ductile/brittleness behavior, mechanical hardness parameters are pre-requisite for the prediction of the applications as structural components at high-temperature [3,52,53]. Knowledge of Debye temperature, minimum thermal conductivity, Grüneisen parameter as well as melting temperature should be known to predict its high-temperature applications [54,55]. Calculation of electronic band structure, the density of states, and charge density mapping is very useful to disclose the bonding nature clearly and explain the mechanical and thermal properties. Thus, a comparative study of newly synthesized chalcogenide could be of scientific interest.

Therefore, we planned to perform a DFT-based investigation of the synthesized Hf2_2SeC and the structural, elastic, electronic, and thermodynamic properties of Hf2_2SeC are presented in this paper. To be more acceptable, the obtained results were compared with those of Hf2_2SC, Zr2_2SeC, Zr2_2SC, and Nb2_2SC MAX phases, where available.

Computational methodology

The results presented here are calculated using the Cambridge Serial Total Energy Package (CASTEP) code [56,57] based on the density functional theory. The generalized gradient approximation (GGA) of the Perdew–Burke–Ernzerhof (PBE) [58] type of functional was used as exchange and correlation term. The C - 2s22p22s^{2}2p^{2}, Se - 4s24p44s^{2}4p^{4}, and Hf - 5d26s25d^{2}6s^{2} electronic orbitals were considered for pseudo-potential calculations. A k-point [59] mesh of size 12×12×412 \times12 \times4 and the cutoff energy of 500 eV was used for the calculations. Further details of the calculations can be found elsewhere [51].

Results and discussion

Structural properties

The crystal structure of Hf2_2SeC is presented in Fig. 1, it belongs to the hexagonal system and the space group is P63_3/mmc (194) [42]. The unit cell is composed of eight atoms, hence, its chemical formula revealed the two formula units. The octahedron Hf6_6C is situated in between two atomic Se layers that can be shown in ref. [51]. The Wyckoff positions of M (Hf), A (Se), X (C) atoms are 4f (1/31/3, 2/32/3, ZM_\mathrm{M}), 2a (1/31/3, 2/32/3, 3/43/4) and 2c (0, 0, 0), respectively [60]. The physical properties of Hf2_2SeC were further calculated after the geometrical relaxation of the unit cell. The cell parameters of the relaxed structure are given along with the previous experimental and theoretical results[2] to assure the setting of the parameters used for calculations. For example, the obtained value of aa is just 0.47% and cc is just 0.88% larger than the experimental results. The discrepancy between the calculated values (present and previous) is much smaller (0.06% and 0.39% for aa and cc, respectively) compared to the experimental values.

Crystal structure of the Hf2SeC compound

Figure 1. Crystal structure (unit cell) of the Hf2_2SeC compound.

aa (Å)cc (Å)c/aRef.PositionsZrSeC
3.43812.5013.636This studyxx1/31/30
3.42212.3913.621Expt. [2]yy2/32/30
3.43612.4523.624Theo. [2]zz0.09453/40
0.0943 [2]

Table 1. Calculated lattice parameters (aa and cc), c/ac/a ratio, and atomic positions of Hf2_2SeC MAX phase.

Mechanical properties

Wang et al [2] calculated the stiffness constants only with an intention to correlate these with the thermal expansion coefficient of MAX phases. However, other important parameters like elastic moduli, failure mode based on Pugh/Poisson’s ratio, mechanical hardness parameters, elastic anisotropic indices, etc. are remained unexplored and will be focused on in this section. To do this, we have re-calculated the stiffness constants (CijC_{ij}) of Hf2_2SeC using the strain-stress method [30, 32, 61, 62, 63] and then used them further to investigate the other parameters mentioned above.

The five independent stiffness constants of Hf2_2SeC are given in Table 2 along with stiffness constants of other S and Se-based MAX phases M2_2AC (M = Hf, Zr, Nb, A = S, Se), where available. Though, Hf2_2SeC is experimentally realized, the mechanical stability of Hf2_2SeC is also checked by use of stiffness constants (CijC_{ij}) based on the Max Born [64] and Mouhat et al.[65] stability conditions as given here: C11>0C_{11} > 0, C11>C12C_{11} > C_{12}, C44>0C_{44} > 0, (C11+C12)C33−2(C13)2>0(C_{11} + C_{12})C_{33} - 2(C_{13})^2 > 0. Since it (Hf2_2SeC) is experimentally synthesized but for realistic use, checking of mechanical stability is mandatory. Table 2 confirms that the obtained CijC_{ij}s meet the stability conditions; hence, there is no doubt about the mechanical stability. In addition, CijC_{ij}s also provide knowledge regarding bonding strength along different axes, hardness, mechanical anisotropy, etc. For instance, the values C11C_{11} and C33C_{33} represent the stiffness along [100] and [1] directions. As evident from Table 2, C11C_{11} is smaller than C33C_{33} for all considered chalcogenide MAX phases implying lower deformation resistance along the aa-axis than the cc-axis. Moreover, C44C_{44} is lower than C33C_{33} and C11C_{11}, certifying an easy shear deformation compared to that of along the axial directions. Finally, the values of C11C_{11}, C33C_{33}, and C44C_{44} (C11≠C33≠C44C_{11} \ne C_{33} \ne C_{44}) confirmed the uneven bonding strength along with the aa and cc-axis as well as shear direction which is owing to the differences in the arrangement of atoms in different directions.

PhaseC11C_{11}C12C_{12}C13C_{13}C33C_{33}C44C_{44}BBGGYYHChenH_{\mathrm{Chen}}HMiaoH_{\mathrm{Miao}}G/BG/Bν\nuCPReference
Hf2_2SeC287779830613015811327318.4721.690.720.21−53This study
30895105314135[2]
Hf2_2SC3119712132714918112029517.3521.720.660.23−52[35]
Zr2_2SeC260979629312815410024714.8517.790.650.23−30[51]
Zr2_2SC2958910231513816611528017.8921.570.690.22−49[35]
Nb2_2SC31610815132512419710526711.5815.840.530.27−16[35]

Table 2. The elastic constants, CijC_{ij} (GPa), bulk modulus, BB (GPa), shear modulus, GG (GPa), Young’s modulus, YY (GPa), Hardness parameters, HChenH_{\mathrm{Chen}}(GPa) and HMiaoH_{\mathrm{Miao}}(GPa), Pugh ratio, G/BG/B, Poisson ratio, ν\nu and Cauchy Pressure, CPCP (GPa) of Hf2_2SeC, along with those of Zr2_2SeC and M2_2SC (M = Zr, Hf, Nb).

The stiffness constants were then used to compute the Bulk modulus (BB) and shear modulus (GG) using Hill’s approximation [66] which is the average of Voigt [67] and Reuss [68] models as follows:

B=(BV+BR)/2, where BV=[2(C11+C12)+C33+4C13]/9B = (B_V + B_R)/2,\ \text{where}\ B_V = [2(C_{11} + C_{12}) + C_{33} + 4C_{13}]/9
BR=C2M;C2=(C11+C12)C33−2C132;M=C11+C12+2C33−4C13.B_R = \frac{C^2}{M};\quad C^2 = (C_{11}+C_{12})C_{33}-2C_{13}^2;\quad M=C_{11}+C_{12}+2C_{33}-4C_{13}.

BVB_V indicates the largest value of BB (Voigt bulk modulus) and BRB_R express the lowest value of BB (Reuss bulk modulus). Similarly, GG was computed using the following equations:

G=(GV+GR)/2,whereGV=[M+12C44+12C66]/30G=(G_V+G_R)/2,\quad\text{where}\quad G_V=[M+12C_{44}+12C_{66}]/30
GR=(52)C2C44C663BVC44C66+C2(C44+C66);C66=(C11−C12)/2.G_R=\left(\frac{5}{2}\right)\frac{C^2C_{44}C_{66}}{3B_VC_{44}C_{66}+C^2(C_{44}+C_{66})};\quad C_{66}=(C_{11}-C_{12})/2.

After then, the BB and GG were used to calculate the Young’s modulus (YY) and Poisson’s ratio (υ\upsilon) using the following equations[35]:

Y=9BG3B+Gandυ=3B−Y6B.Y=\frac{9BG}{3B+G}\quad\text{and}\quad\upsilon=\frac{3B-Y}{6B}.

Finally, BB, GG, YY and υ\upsilon were used to calculate the Hardness parameters using the equations [69, 70]:

HChen=2(k2G)0.585−3H_{\mathrm{Chen}}=2(k^2G)^{0.585}-3

(where, Pugh’s ratio, k=G/Bk=G/B) and

HMiao=(1−2υ)E6(1+υ).H_{\mathrm{Miao}}=\frac{(1-2\upsilon)E}{6(1+\upsilon)}.

Now, let us have a comparative discussion based on the values presented in Table 2. The value of C11C_{11} for Hf2_2SeC is higher than that of another Se containing MAX phase, Zr2_2SeC. On other hand, it is lower than those other S-based MAX phases, which is also true for C33C_{33}. Next, C44C_{44} of Hf2_2SeC is higher than that of Zr2_2SeC and Nb2_2SC but lower than that M2_2SC (M = Hf, Zr). As it is well known, C44C_{44} is a very good hardness predictor, i.e., more directly related to the elastic moduli compared to other stiffness constants and also used for the measurement of deformation resistance. Thus, according to the C44C_{44}, the compounds can be ranked as follows: Hf2_2SC > Zr2_2SC > Hf2_2SeC > Zr2_2SeC > Nb2_2SC. Among the elastic moduli, GG is a more accurate predictor for shear deformation compared to BB and/or YY. The ranking of the compounds is same as for C44C_{44}, i.e., Hf2_2SC > Zr2_2SC > Hf2_2SeC > Zr2_2SeC > Nb2_2SC. The YY is a good predictor for the stiffness measurement of the solids and the solid is said to be stiffer with a higher YY value. Thus, the compounds can be ranked as follows: Hf2_2SC > Zr2_2SC > Hf2_2SeC > Nb2_2SC > Zr2_2SeC. However, the BB of Nb2_2SC somehow has the highest value. The ranking based on the BB is also the same for other compounds except for Nb2_2SC, i.e., Hf2_2SC > Zr2_2SC > Hf2_2SeC > Zr2_2SeC. Next, the hardness parameters using the Chen’s [69] and Miao [70] formulae were calculated and presented in Table 2. As shown, The HChenH_{\mathrm{Chen}} of Hf2_2SeC is comparatively higher than other chalcogenides presented here despite its lower values of elastic constants compared to Hf2_2SC and Zr2_2SC. The elastic constants don‘t reflect material’s hardness directly, though, the parameters have usually higher values for harder solids. Thus, the titled chalcogenide is expected to be harder than the others presented here. HmiaoH_{\mathrm{miao}} of Hf2_2SeC is also higher than that of other chalcogenides except for Hf2_2SC where HmiaoH_{\mathrm{miao}} of Hf2_2SeC is 0.13% lowered than that of Hf2_2SC. In addition, Pan et al [71] demonstrated that the Pugh ratio (which is also used in Chen’s formula) is indirectly related to the Vickers hardness, which is highest for Hf2SeC\mathrm{Hf}_{2}\mathrm{SeC} compared to other compounds considered here. It is noted that the hardness parameters of Hf2SeC\mathrm{Hf}_{2}\mathrm{SeC} are lowered than that of Ti2SC\mathrm{Ti}_{2}\mathrm{SC} [32] (HChenH_{\mathrm{Chen}}- 23.48 GPa, HmiaoH_{\mathrm{miao}}-29.85 GPa, the elastic moduli are also higher) chalcogenide MAX phase. Thus, by taking into consideration the above facts, it is obvious to say that the titled compound possesses the 2{sup}nd highest hardness among the chalcogenide MAX phases. Despite the explanation stated above, still, the mystery (hardness of Hf2SC\mathrm{Hf}_{2}\mathrm{SC} is lower than that of Hf2SeC\mathrm{Hf}_{2}\mathrm{SeC} though the stiffness constants and elastic moduli are higher) should be solved by further clarification in terms of the total density of states (DOS).

To check the ductility/brittleness character we used three well formalisms. Pugh ratio (G/BG/B), the ratio of bulk to shear modulus, is a well-accepted parameter to separate the ductile and brittle materials with a critical value of 0.571. A value of G/BG/B greater than 0.571 implies the brittleness character of solids and vice versa [72]. As evident, the titled MAX phase is brittle like its precursor Hf2SC\mathrm{Hf}_{2}\mathrm{SC}. The Poisson’s ratio [73] is another parameter used to define a solid either ductile or brittle with a critical value of 0.26. Values lower than 0.26 indicate the brittleness character of solids and vice versa. It is seen in Table 2, that the titled phase is brittle again. Next, the Cauchy pressure [74] is also used to define a material either ductile or brittle. Values of a negative sign indicate the brittle solids while the positive sign indicates the ionic ductile solids. Table 2 revealed that the titled Se based MAX phase is brittle. A large negative value also indicates the dominant nature of a covalent bond in which a mixture of bonding is present. Thus, the covalent bond is dominant in the Hf2SeC\mathrm{Hf}_{2}\mathrm{SeC} MAX phase where a mixture of covalent and ionic bonding is present.

Electronic properties

Fig. 2 (a) shows the DOS of Hf2SeC\mathrm{Hf}_{2}\mathrm{SeC} and Hf2SC\mathrm{Hf}_{2}\mathrm{SC} in which black vertical lines indicate the peaks in the DOS of Hf2SeC\mathrm{Hf}_{2}\mathrm{SeC} and red lines indicate the peaks in the DOS of Hf2SC\mathrm{Hf}_{2}\mathrm{SC}. The reference lines clearly indicate the peak shifting to the left when we go from S to Se. The peaks in the DOS are the results of hybridization among the different states involved in solids. The strength of the bonding between states depends on the position. The peak in the low energy sides, higher the bonding strength[19, 35, 75]. Thus, the bonding among the states in Hf2SeC\mathrm{Hf}_{2}\mathrm{SeC} is expected to be stronger compared to Hf2SC\mathrm{Hf}_{2}\mathrm{SC} as a consequence, the hardness of Hf2SeC\mathrm{Hf}_{2}\mathrm{SeC} is also expected to be higher compared to Hf2SC\mathrm{Hf}_{2}\mathrm{SC} that is found in the present study. In addition, the DOS at the Fermi level is around 1.33 states/eV/cell for both phases, which implies the metallic nature of Hf2SeC\mathrm{Hf}_{2}\mathrm{SeC}. To confirm electronic conductivity, we have calculated the electronic band structure presented in the following section.

Image not extracted

Figure 1 (PDF p. 8). (a) The DOS of Hf2AC\mathrm{Hf}_{2}\mathrm{AC} (A = Se, S), (b) electronic band structure of Hf2SeC\mathrm{Hf}_{2}\mathrm{SeC} and (c) charge density mapping of Hf2AC\mathrm{Hf}_{2}\mathrm{AC} (A = Se, S).

The electronic band structure is also an important result concerning its electronic conductivity. The electronic band structure of Hf2SeC\mathrm{Hf}_{2}\mathrm{SeC} calculated from the relaxed structure is shown in Fig. 2 (b) along the high symmetry lines: Γ\Gamma–A–H–K–Γ\Gamma–M–L–H. Like all other MAX phases[76], Hf2SeC\mathrm{Hf}_{2}\mathrm{SeC} also exhibits metallic nature that can be confirmed from the band structure in which overlapping of valence and conduction band is observed. Another interesting character is also noticed from the band structure, the energy dispersion along (cc-direction): Γ\Gamma–A, K–H, and L–M directions are smaller compared to the energy dispersion (basal plane): H–K, Γ\Gamma–M, and L–H, thus, the electronic conductivity is not equal in the basal plane and cc-direction. Smaller energy dispersion is owing to the higher electronic effective mass tensor that leads to a smaller conductivity and vice versa [19]. Thus, the typical conductivity nature for MAX phases [19, 30, 77] is also exhibited by Hf2_2SeC: higher conductivity is observed in the basal plane in comparison with that of cc-direction.

Fig. 2 (c) displays the CDM (in the units of e/Å3^3) in the (100) crystallographic plane which is designed to explore the nature of the bonding among the different atoms for Hf2_2SeC and Hf2_2SC. The positions of the atoms are denoted in the figure. As evident, the Hf-C boning is a purely covalent bond like other MAX phases. The Hf-Se/S bonding is a mixture of a covalent and ionic type which is also another common nature for MAX phase materials. The replacement of A atom from Se to S results in a considerable change in the CDMs. As seen, the charge density (CD) at A (S) position increases. Thus, the common bonding nature of MAX phases is revealed by CDM for both Hf2_2AC (A = Se, S) which is responsible for the combined properties of metals and ceramics.

Mechanical anisotropy

Because of the layered hexagonal symmetry for the MAX phase materials, the atomic arrangement is different along aa and cc-direction, consequently, unequal values of the C11C_{11} and C33C_{33} are obtained (Table 2). As a further consequence, mechanical anisotropy is observed like other MAX phases [30, 32, 78, 79, 80]. The important phenomena such as microcracks and anisotropic plastic deformation are the results of the mechanical anisotropy that shows a significant contribution in realizing the mechanical stability of the solids in extreme conditions. Due to the aforementioned reasons, the anisotropic nature of the mechanical properties characterizing parameters has been studied. To do this, We have calculated the different anisotropic factors for the {100}, {010} and {001} directions calculated using the equations[81]:

A1=16(C11+C12+2C33−4C13)C44, A2=2C44C11−C12, A3=A1⋅A2=13(C11+C12+2C33−4C13)C11−C12A_1 = \frac{\frac{1}{6}(C_{11}+C_{12}+2C_{33}-4C_{13})}{C_{44}},\ A_2 = \frac{2C_{44}}{C_{11}-C_{12}},\ A_3 = A_1 \cdot A_2 = \frac{\frac{1}{3}(C_{11}+C_{12}+2C_{33}-4C_{13})}{C_{11}-C_{12}}

The obtained values are presented in Table 3 along with other chalcogenide MAX phase carbides that confirm the anisotropy of Hf2_2SeC where the non-zero values of AiA_i’s indicating the level of anisotropy. The B along aa and cc-direction are estimated using the relations

PhaseA1A_1A2A_2A3A_3kc/kak_c/k_aBaB_aBcB_cAUA^{\mathrm{U}}Ref.
Hf2_2SeC0.751.240.930.814435480.081This
Hf2_2SC0.651.390.900.815056270.178[35]
Zr2_2SeC0.731.571.140.843839040.218[?]
Zr2_2SC0.731.340.980.854129550.113[35]
Nb2_2SC0.631.190.750.705307560.161[35]

Table 3. The anisotropic factors, A1A_1, A2A_2, A3A_3, BaB_a, BcB_c, kc/kak_c/k_a, and universal anisotropic index AUA^{\mathrm{U}} of M2_2AC (M=Hf, Zr; A = Se, S) and Nb2_2SC.

Ba=adPda=Λ2+αandBc=cdPdc=Baα,B_a = a\frac{dP}{da} = \frac{\Lambda}{2+\alpha} \quad\text{and} \quad B_c = c\frac{dP}{dc} = \frac{B_a}{\alpha},

respectively [82] where Λ=2(C11+C12)+4C13α+C33α2\Lambda= 2(C_{11}+C_{12})+4C_{13}\alpha+C_{33}\alpha^2 and α=(C11+C12)−2C13C33−C13\alpha= \frac{(C_{11}+C_{12})-2C_{13}}{C_{33}-C_{13}}. As evident from Table 3, Ba≠BcB_a \ne B_c means the B of Hf2_2SeC is anisotropic in nature. The linear compressibility (kk) along the aa and cc-axis is estimated by the equation [83]:

kcka=C11+C12−2C13/(C33−C13)\frac{k_c}{k_a} = C_{11}+C_{12}-2C_{13}/(C_{33}-C_{13})

The ratio of kc/kak_c/k_a is not one (1) (kc/kak_c/k_a is equal to 1 for isotropic materials) that confirms the anisotropic nature of Hf2_2SeC. The universal anisotropic index AUA^{\mathrm{U}} is estimated by the following equation [84]:

AU=5GVGR+BVBR−6≥0(1)A^{\mathrm{U}} = 5\frac{G_{\mathrm{V}}}{G_{\mathrm{R}}}+\frac{B_{\mathrm{V}}}{B_{\mathrm{R}}}-6 \ge0 \tag*{(1)}

where BB and GG are obtained by Voigt and Reuss models. Since, the values of AUA^{\mathrm{U}} are greater than zero, indicating the anisotropic nature of Hf2_2SeC. At end of this section, it is seen that the titled chalcogenide exhibits anisotropy in its elastic properties like other chalcogenide MAX phase carbides (Table 3).

In order to better comprehend the mechanical anisotropy, the directional dependent 2D projections and 3D plots of elastic properties are used to illustrate this anisotropic behavior. Figure 3 depicts the demonstration of anisotropy in Young’s and shear moduli along with linear compressibility (KK) and Poisson’s ratio (υ\upsilon). The YY and KK are isotropic in the xyxy plane while anisotropic in the xzxz and yzyz planes (Figure 3 a and b), which are confirmed by perfectly circular (xyxy plane) and non-circular (xzxz and yzyz planes) 2D projections. In the xyxy plane, the YY and KK values are equal at the xx and yy axis. In the xzxz and yzyz planes, the Ymax⁡Y_{\max} is at the 45∘45^{\circ} of horizontal and vertical axis whereas Kmax⁡K_{\max} is at the horizontal axis (Table 4).

PhasesYmin⁡Y_{\min}Ymax⁡Y_{\max}AYA_YKmin⁡K_{\min}Kmax⁡K_{\max}AKA_KGmin⁡G_{\min}Gmax⁡G_{\max}AGA_Gυmin⁡\upsilon_{\min}υmax⁡\upsilon_{\max}AυA_{\upsilon}Ref.
Hf2_2SeC247.7295.41.191.8312.2551.2399.07130.271.310.1330.2772.07This
Hf2_2SC255.03327.561.281.591.971.2498.48148.951.510.0990.3273.28[35]
Zr2_2SC250.08306.391.221.782.121.19101.19137.271.350.1100.2902.53[35]
Zr2_2SeC208.93277.501.321.9132.2881.1981.071127.591.570.0780.3434.394[51]
Nb2_2SC217.27297.021.361.321.881.4388.96128.571.500.1540.3932.55[35]

Table 4. Maximum and minimum values of Youngs modulus, YY (GPa), linear compressibility, KK (TPa−1^{-1}), shear modulus, GG (GPa), and Poisson's ratio, υ\upsilon (GPa) of M2_2AC (M = Hf, Zr; A = Se, S) and Nb2_2SC.

The 2D projections and 3D plots of Young’s modulus, linear compressibility, shear modulus, and Poisson’s ratio in Hf2SeC

Figure 3. The 2D projections and 3D plots of (a) Young’s modulus, (b) linear compressibility, (c) shear modulus, and (d) Poisson’s ratio in Hf2_2SeC.

The color contrast on their 3D plots is consistent with the values in the 2D projections. The 2D projections of GG and ν\nu exhibit inner and outer surfaces (represented by green and blue lines) shown in Figure 3 (c and Figure 3d). The circular 2D projections of the inner and outer surface in xyxy plane reveal their isotropic nature similar to YY and KK. In xzxz and yzyz planes, the outer surface of GG and ν\nu has the maximum value (Gmax⁡G_{\max} and νmax⁡\nu_{\max}) at the horizontal axis while the inner surface has a maximum value (Gmax⁡G_{\max} and νmax⁡\nu_{\max}) at the vertical axis. Due to this, the color contrast in 3D plots shows the maximum gradient at the xx, yy and zz-axis while the minimum gradient at the 45∘45^\circ of the horizontal and vertical axis in the xzxz and yzyz planes. These computed values of YY, GG, KK, and ν\nu are tabulated along with their anisotropic index in Table 4. This analysis shows that elastic properties are non-identical in all of the crystallographic planes and the degree of anisotropy is maximum along the zz-axis. In comparison with other chalcogenide MAX phases, the level of anisotropy for Hf2SeCHf_{2}SeC is lowest [Table 4].

Thermodynamic properties

MAX phases exhibit promising high-temperature applications such as heating elements, protective coatings, electrical contacts, and have the potential for thermal barrier coatings (TBCs) [85]. It is important to disclose their thermodynamic properties for possible applications. Therefore, we used the quasi-harmonic Debye model [86] [87] to compute the thermodynamic properties of Hf2SeCHf_{2}SeC in the temperature and pressure range of 0 to 1000°C and 0 to 50 GPa, respectively. The relationship of unit cell volume as a function of temperature and pressure is presented in Figure 4. With the increase in temperature and pressure, the unit cell volume expands and contracts linearly. The expansion rate as a function of temperature is relatively less at 50 GPa as compared to at 0 GPa. Here, the calculated unit cell volume of 128.3 A˚3128.3\ \text{\AA}^{3} at 0 GPa and 300 K, is consistent with the equilibrium volume computed during optimization. The Grüneisen parameter (γ\gamma) for Hf2SeCHf_{2}SeC is following the same trend as unit cell volume. There is a linear increase and decrease in the Grüneisen parameter with an increase in temperature and pressure, respectively as shown in Figure 5.

Figure 4. Variations in unit cell volume as a function of temperature and pressure.

Figure 5. Variations in Grüneisen parameter as a function of temperature and pressure.

The change in Debye temperature with the variation of temperature and pressure is illustrated in Figure 6. It is found that the Debye temperature decreases with an increase in temperature while decreasing with an increase in pressure. At 0 GPa and 300 K, the Debye temperature of Hf2SeC\mathrm{Hf}_{2}\mathrm{SeC} is 640 K which is comparable with its counterpart Hf2SC\mathrm{Hf}_{2}\mathrm{SC} (598 K)[51]. We have also computed the Debye temperature (ΘD\Theta_{\mathrm{D}}) using Anderson’s model [88] for both Hf2AC\mathrm{Hf}_{2}\mathrm{AC} (A = Se, S). The ΘD\Theta_{\mathrm{D}} of Hf2SeC\mathrm{Hf}_{2}\mathrm{SeC} (640 K, 490 K) is higher than that of Hf2SC\mathrm{Hf}_{2}\mathrm{SC} (598 K, 454 K), is in good agreement with the statement that higher ΘD\Theta_{\mathrm{D}} corresponds to the harder solids [Section 3.2, hardness of Hf2SeC\mathrm{Hf}_{2}\mathrm{SeC} is higher than Hf2_2SeC]. Furthermore, the melting temperature of the titled phase is computed using the model [89]

Figure 6. Variations in Debye temperatureas a function of temperature and pressure.

Tm=3C11+1.5C33+354T_m = 3C_{11} + 1.5C_{33} + 354

, where C11C_{11} and C33C_{33} are the elastic constants. The calculated melting point of 1674 K is comparable (slightly lower) with that of Hf2_2SC (1778 K), which implies that it is also suitable for high-temperature applications. The TmT_m is related to Young’s modulus (YY), the higher TmT_m is for the solids with higher YY. The obtained values also agree with the YY values (Hf2_2SeC – 273 GPa and Hf2_2SC – 295 GPa). Moreover, the minimum thermal conductivity is also calculated using the formula [90]: Kmin⁡=kBvm(MnρNA)−2/3K_{\min}=k_Bv_m\left(\frac{M}{n\rho N_A}\right)^{-2/3} where kBk_B, vmv_m, NAN_A, and ρ\rho are Boltzmann constant, average phonon velocity, Avogadro’s number, and density of crystal, respectively. The obtained Kmin⁡K_{\min} is 0.86 (W/mK) which is almost equal to that Hf2_2SC [0.85 (W/mK)] [35], smaller than Zr2_2SeC [1.33 (W/mK)] and M2_2SC (M = Zr, Nb) [35], also suggests for use in high temperature technology as a coating materials.

In Figure 7, the dependence of the thermal expansion coefficient (TECTEC) on the temperature and pressure is given. The TECTEC is constant at 0 K in the pressure range of 0 to 50 GPa. The TECTEC is increase sharply up to the temperature of 400 K, later, it increases at a gradual rate. The increase in TECTEC at 0 GPa is higher as compared to 50 GPa. At any constant temperature, the TECTEC decreases linearly with the increase in pressure. The computed TECTEC for Hf2_2SeC is 2.66×10−52.66 \times10^{-5} K−1^{-1} is comparable with that of Zr2_2SeC 3.88×10−53.88 \times10^{-5} K−1^{-1}[51]. The dependence of specific heat at constant volume (CvC_v) on temperature and pressure is presented in Figure 8. The variation in CvC_v as a function of temperature obeys the Debye T3T^{3}-law and finally becomes constant to reach the classical Dulong-petit (DP) limit i.e., Cv=3nNkB=195.7 J mol−1 K−1C_{v} = 3nNk_{B} = 195.7\ \mathrm{J\,mol^{-1}\,K^{-1}}. At 0 K, CvC_{v} remains constant while decreaseing linearly at higher temperatures as a function of pressure until a temperature where CvC_{v} gets converged to reach the DP limit.

Figure 7. Variations in thermal expansion coefficient as a function of temperature and pressure.

Figure 8. Variations in specific heat at constant volume as a function of temperature and pressure.

We conclude this section as follows: a good relationship between mechanical and thermal properties is found such as higher Debye temperature for Hf2SeC\mathrm{Hf}_{2}\mathrm{SeC} than Hf2SC\mathrm{Hf}_{2}\mathrm{SC} due to higher hardness and higher melting point for Hf2_2SC than Hf2_2SeC due to higher Young’s modulus owing to their interdependence nature. In comparison with TBC materials [91,92], the Debye temperature, melting temperature as well as minimum thermal conductivity values suggest that Hf2_2SeC is like to be a possible thermal barrier coating material.

Conclusions

A recently synthesized chalcogenide MAX phase Hf2_2SeC has been studied using the DFT-based first-principles study. The obtained lattice constants agree well with the previous results. The synthesized titled MAX phase is also mechanically stable. The unequal values of C11C_{11} and C33C_{33} imply the anisotropic nature. The obtained parameters for mechanical behavior are comparable with those of other chalcogenide MAX phases. Elastic constants and moduli of Hf2_2SeC are lower than that of its precursor phase Hf2_2SC while the hardness follows the reverse trend. The titled boride is like to be 2{sup}nd` hardest chalcogenide MAX phase. The Hf2_2SeC is brittle like other MAX phases whereas Hf2_2SeC is more brittle compared to its precursor Hf2_2SC. The variation of hardness among Hf2_2AC (A = Se, S) is well explained in terms of DOSs. The band structure confirms the metallic nature whereas the charge density mapping discloses the mixture of covalent and ionic bonds. The electronic conductivity is anisotropic in nature. Different anisotropic indices, and 2D and 3D plots of YY, BB, GG, and υ\upsilon also revealed the anisotropic behavior of the mechanical properties. The variation of the thermal properties with temperature and pressure follows the usual trend. The estimated Debye temperature, melting point, and minimum thermal conductivity reveal the possibility of Hf2_2SeC to be used in high-temperature technology as a TBC material. It is expected that the present study will stimulate the scientific community to discover more Se-based MAX phases in the future.

Conflicts of interest

The authors declare no conflicts of interest.

Funding: This research did not receive any specific grant from funding agencies in the public, commercial, or not-for-profit sectors.

References

  1. [1]K. Chen, X. Bai, X. Mu, P. Yan, N. Qiu, Y. Li, J. Zhou, Y. Song, Y. Zhang, S. Du, Z. Chai, Q. Huang, MAX phase Zr2SeC and its thermal conduction behavior, J. Eur. Ceram. Soc. 41 (2021) 4447–4451. https://doi.org/10.1016/j.jeurceramsoc.2021.03.013.
  2. [14]B. Tunca, T. Lapauw, R. Delville, D.R. Neuville, L. Hennet, D. Thiaudière, T. Ouisse, J. Hadermann, J. Vleugels, K. Lambrinou, Synthesis and Characterization of Double Solid Solution (Zr,Ti) 2 (Al,Sn)C MAX Phase Ceramics, Inorg. Chem. 58 (2019) 6669–6683. https://doi.org/10.1021/acs.inorgchem.9b00065.
  3. [15]M. Griseri, B. Tunca, S. Huang, M. Dahlqvist, J. Rosén, J. Lu, P.O.Å. Persson, L. Popescu, J. Vleugels, K. Lambrinou, Ta-based 413 and 211 MAX phase solid solutions with Hf and Nb, J. Eur. Ceram. Soc. 40 (2020) 1829–1838. https://doi.org/10.1016/j.jeurceramsoc.2019.12.052.
  4. [16]E.Z.S.G. Christopoulos, N. Ni, D.C. Par, D. Horlait, M.E. Fitzpatrick, A. Chroneos, W.E. Lee, Experimental synthesis and density functional theory investigation of radiation tolerance of Zr 3 ( Al 1-x Si x ) C 2 MAX phases, (2017) 1–11. https://doi.org/10.1111/jace.14742.
  5. [17]R. Pan, J. Zhu, Y. Liu, Synthesis, microstructure and properties of (Ti 1 − x , Mo x ) 2 AlC phases, Mater. Sci. Technol. 34 (2018) 1064–1069. https://doi.org/10.1080/02670836.2017.1419614.
  6. [18]C. Zuo, C. Zhong, Screen the elastic and thermodynamic properties of MAX solid solution using DFT proceude: Case study on (Ti1-xVx)2AlC, Mater. Chem. Phys. (2020) 123059. https://doi.org/10.1016/j.matchemphys.2020.123059.
  7. [19]M.A. Ali, S.H. Naqib, Recently synthesized (Ti 1−x Mo x ) 2 AlC (0 ≤ x ≤ 0.20) solid solutions: deciphering the structural, electronic, mechanical and thermodynamic properties via ab initio simulations, RSC Adv. 10 (2020) 31535–31546. https://doi.org/10.1039/D0RA06435A.
  8. [20]C.M. Hamm, J.D. Bocarsly, G. Seward, U.I. Kramm, C.S. Birkel, Non-conventional synthesis and magnetic properties of MAX phases (Cr/Mn)2AlC and (Cr/Fe)2AlC, J. Mater. Chem. C. 5 (2017). https://doi.org/10.1039/c7tc00112f.
  9. [21]M.A. Ali, Newly Synthesized Ta- Based MAX Phase (Ta 1− x Hf x ) 4 AlC 3 and (Ta 1− x Hf x ) 4 Al 0.5 Sn 0.5 C 3 (0 ≤ x ≤ 0.25) Solid Solutions: Unravelling the Mechanical, Electronic, and Thermodynamic Properties, Phys. Status Solidi. 258 (2021) 2000307. https://doi.org/10.1002/pssb.202000307.
  10. [22]M.A. Ali, M.R. Khatun, N. Jahan, M.M. Hossain, Comparative study of Mo 2 Ga 2 C with superconducting MAX phase Mo 2 GaC: First-principles calculations, Chinese Phys. B. 26 (2017) 033102. https://doi.org/10.1088/1674-1056/26/3/033102.
  11. [23]C. Hu, C.-C. Lai, Q. Tao, J. Lu, J. Halim, L. Sun, J. Zhang, J. Yang, B. Anasori, J. Wang, Y. Sakka, L. Hultman, P. Eklund, J. Rosen, M.W. Barsoum, Mo 2 Ga 2 C: a new ternary nanolaminated carbide, Chem. Commun. 51 (2015) 6560–6563. https://doi.org/10.1039/C5CC00980D.
  12. [24]H. He, S. Jin, G. Fan, L. Wang, Q. Hu, A. Zhou, Synthesis mechanisms and thermal stability of ternary carbide Mo2Ga2C, Ceram. Int. 44 (2018) 22289–22296. https://doi.org/10.1016/j.ceramint.2018.08.353.
  13. [25]H. Chen, D. Yang, Q. Zhang, S. Jin, L. Guo, J. Deng, X. Li, X. Chen, A Series of MAX Phases with MA-Triangular-Prism Bilayers and Elastic Properties, Angew. Chemie - Int. Ed. 58 (2019) 4576–4580. https://doi.org/10.1002/anie.201814128.
  14. [26]Q. Tao, J. Lu, M. Dahlqvist, A. Mockute, S. Calder, A. Petruhins, R. Meshkian, O. Rivin, D. Potashnikov, E.N. Caspi, H. Shaked, A. Hoser, C. Opagiste, R.-M. Galera, R. Salikhov, U. Wiedwald, C. Ritter, A.R. Wildes, B. Johansson, L. Hultman, M. Farle, M.W. Barsoum, J. Rosen, Atomically Layered and Ordered Rare-Earth i-MAX Phases: A New Class of Magnetic Quaternary Compounds, Chem. Mater. 31 (2019) 2476–2485. https://doi.org/10.1021/acs.chemmater.8b05298.
  15. [27]L. Chen, M. Dahlqvist, T. Lapauw, B. Tunca, F. Wang, J. Lu, R. Meshkian, K. Lambrinou, B. Blanpain, J. Vleugels, J. Rosen, Theoretical Prediction and Synthesis of (Cr 2/3 Zr 1/3 ) 2 AlC i-MAX Phase, Inorg. Chem. 57 (2018) 6237–6244. https://doi.org/10.1021/acs.inorgchem.8b00021.
  16. [28]N. Miao, J. Wang, Y. Gong, J. Wu, H. Niu, S. Wang, K. Li, A.R. Oganov, T. Tada, H. Hosono, Computational Prediction of Boron-Based MAX Phases and MXene Derivatives, Chem. Mater. 32 (2020) 6947–6957. https://doi.org/10.1021/acs.chemmater.0c02139.
  17. [29]J. Wang, T.N. Ye, Y. Gong, J. Wu, N. Miao, T. Tada, H. Hosono, Discovery of hexagonal ternary phase Ti2InB2 and its evolution to layered boride TiB, Nat. Commun. 10 (2019) 1–8. https://doi.org/10.1038/s41467-019-10297-8.
  18. [30]M.A. Ali, M.M. Hossain, M.M. Uddin, A.K.M.A. Islam, D. Jana, S.H. Naqib, DFT insights into new B-containing 212 MAX phases: Hf2AB2 (A = In, Sn), J. Alloys Compd. 860 (2021) 158408. https://doi.org/10.1016/j.jallcom.2020.158408.
  19. [31]M.A. Ali, M.M. Hossain, M.M. Uddin, A.K.M.A. Islam, S.H. Naqib, Understanding the improvement of thermo-mechanical and optical properties of 212 MAX phase borides Zr2AB2 (A = In, Tl), J. Mater. Res. Technol. 15 (2021) 2227–2241. https://doi.org/10.1016/j.jmrt.2021.09.042.
  20. [32]M.A. Ali, M.M. Hossain, A.K.M.A. Islam, S.H. Naqib, Ternary boride Hf3PB4: Insights into the physical properties of the hardest possible boride MAX phase, J. Alloys Compd. 857 (2021) 158264. https://doi.org/10.1016/j.jallcom.2020.158264.
  21. [33]M.W. Qureshi, M.A. Ali, X. Ma, Screen the thermomechanical and optical properties of the new ductile 314 MAX phase boride Zr3CdB4: A DFT insight, J. Alloys Compd. 877 (2021) 160248. https://doi.org/10.1016/j.jallcom.2021.160248.
  22. [34]P. Chakraborty, A. Chakrabarty, A. Dutta, T. Saha-Dasgupta, Soft MAX phases with boron substitution: A computational prediction, Phys. Rev. Mater. 2 (2018) 103605. https://doi.org/10.1103/PhysRevMaterials.2.103605.
  23. [35]M.A. Ali, M.M. Hossain, M.M. Uddin, M.A. Hossain, A.K.M.A. Islam, S.H. Naqib, Physical properties of new MAX phase borides M 2 SB (M = Zr, Hf and Nb) in comparison with conventional MAX phase carbides M 2 SC (M = Zr, Hf and Nb): Comprehensive insights, J. Mater. Res. Technol. 11 (2021) 1000–1018.
  24. [60]28 (2000) 201–281. https://doi.org/10.1016/S0079-6786(00)00006-6.
  25. [61]Y.X. Wang, Z.X. Yan, W. Liu, G.L. Zhou, Structure stability, mechanical properties and thermal conductivity of the new hexagonal ternary phase Ti2InB2 under pressure, Philos. Mag. 100 (2020) 2054–2067. https://doi.org/10.1080/14786435.2020.1754485.
  26. [62]Y. Medkour, A. Bouhemadou, A. Roumili, Structural and electronic properties of M2InC (M = Ti, Zr, and Hf), Solid State Commun. 148 (2008) 459–463. https://doi.org/10.1016/j.ssc.2008.09.006.
  27. [63]M.W. Qureshi, X. Ma, G. Tang, R. Paudel, Ab initio predictions of structure and physical properties of the Zr2GaC and Hf2GaC MAX- phases under pressure, Sci. Reports |. 11 (2021) 1–23. https://doi.org/10.1038/s41598-021-82402-1.
  28. [64]M. Born, On the stability of crystal lattices. I, Math. Proc. Cambridge Philos. Soc. 36 (1940) 160–172. https://doi.org/10.1017/S0305004100017138.
  29. [65]F. Mouhat, F.-X. Coudert, Necessary and sufficient elastic stability conditions in various crystal systems, Phys. Rev. B. 90 (2014) 224104. https://doi.org/10.1103/PhysRevB.90.224104.
  30. [66]R. Hill, The Elastic Behaviour of a Crystalline Aggregate, Proc. Phys. Soc. Sect. A. 65 (1952) 349–354. https://doi.org/10.1088/0370-1298/65/5/307.
  31. [67]W. Voigt, Lehrbuch der Kristallphysik, Vieweg+Teubner Verlag, Wiesbaden, 1966. https://doi.org/10.1007/978-3-663-15884-4.
  32. [68]A. Reuss, Berechnung der Fließgrenze von Mischkristallen auf Grund der Plastizitätsbedingung für Einkristalle ., ZAMM - J. Appl. Math. Mech. / Zeitschrift Für Angew. Math. Und Mech. 9 (1929) 49–58. https://doi.org/10.1002/zamm.19290090104.
  33. [69]X.-Q. Chen, H. Niu, D. Li, Y. Li, Modeling hardness of polycrystalline materials and bulk metallic glasses, Intermetallics. 19 (2011) 1275–1281. https://doi.org/10.1016/j.intermet.2011.03.026.
  34. [70]N. Miao, B. Sa, J. Zhou, Z. Sun, Theoretical investigation on the transition-metal borides with Ta3B4-type structure: A class of hard and refractory materials, Comput. Mater. Sci. 50 (2011) 1559–1566. https://doi.org/10.1016/J.COMMATSCI.2010.12.015.
  35. [71]Y. Pan, X. Wang, S. Li, Y. Li, M. Wen, DFT prediction of a novel molybdenum tetraboride superhard material, RSC Adv. 8 (2018) 18008–18015. https://doi.org/10.1039/c8ra02324g.
  36. [72]S.F. Pugh, XCII. Relations between the elastic moduli and the plastic properties of polycrystalline pure metals, London, Edinburgh, Dublin Philos. Mag. J. Sci. 45 (1954) 823–843. https://doi.org/10.1080/14786440808520496.
  37. [73]M. Roknuzzaman, M.A. Hadi, M.A. Ali, M.M. Hossain, N. Jahan, M.M. Uddin, J.A. Alarco, K. Ostrikov, First hafnium-based MAX phase in the 312 family, Hf 3 AlC 2 : A first-principles study, J. Alloys Compd. 727 (2017) 616–626. D.G. Pettifor, Theoretical predictions of structure and related properties of intermetallics, Mater. Sci. Technol. 8 (1992) 345–349. https://doi.org/10.1179/026708392790170801.
  38. [75]M.A. Ali, M.M. Hossain, M.A. Hossain, M.T. Nasir, M.M. Uddin, M.Z. Hasan, A.K.M.A. Islam, S.H. Naqib, Recently synthesized (Zr 1-x Ti x ) 2 AlC (0 ≤ x ≤ 1) solid solutions: Theoretical study of the effects of M mixing on physical properties, J. Alloys Compd. 743 (2018) 146–154. https://doi.org/10.1016/j.jallcom.2018.01.396.
  39. [76]Y. Zhou, Z. Sun, Electronic structure and bonding properties of layered machinable and ceramics, Phys. Rev. B - Condens. Matter Mater. Phys. 61 (2000) 12570–12573. https://doi.org/10.1103/PhysRevB.61.12570.
  40. [77]J. Wang, Y. Zhou, Dependence of elastic stiffness on electronic band structure of nanolaminate M 2 AlC (M = Ti , V , Nb , and Cr ) ceramics, 214111 (2004) 1–9. https://doi.org/10.1103/PhysRevB.69.214111.
  41. [78]Y.Y. Liu, Y.X. Wang, Z.X. Yan, W. Liu, G.L. Zhou, K.Z. Xiong, J.B. Gu, Pressure effects on structure, mechanical properties and thermal conductivity of V2SnC: a first-principles study, Philos. Mag. 0 (2021) 1–16. https://doi.org/10.1080/14786435.2021.1988747.
  42. [79]M.W. Qureshi, X. Ma, G. Tang, R. Paudel, Ab initio predictions of structure and physical properties Hf 2 GaC MAX of the - Zr 2 GaC and - phases under pressure, (2021) 1–24. https://doi.org/10.1038/s41598-021-82402-1.
  43. [80]W. Sailuam, I. Fongkaew, S. Limpijumnong, K. Phacheerak, A first principles investigation on the structural, elastic, and mechanical properties of MAX phase M3AlC2 (M= Ta, Ti, V) as a function of pressure, Comput. Condens. Matter. 30 (2022) e00638. https://doi.org/10.1016/j.cocom.2021.e00638.
  44. [81]H.M. Ledbetter, Elastic properties of zinc: A compilation and a review, J. Phys. Chem. Ref. Data. 6 (1977) 1181–1203. https://doi.org/10.1063/1.555564.
  45. [82]A.K.M.A. Islam, A.S. Sikder, F.N. Islam, NbB2: a density functional study, Phys. Lett. A. 350 (2006) 288–292. https://doi.org/10.1016/j.physleta.2005.09.085.
  46. [83]J. Wang, Y. Zhou, T. Liao, Z. Lin, First-principles prediction of low shear-strain resistance of Al3BC3: A metal borocarbide containing short linear BC2 units, Appl. Phys. Lett. 89 (2006) 021917. https://doi.org/10.1063/1.2220549.
  47. [84]S.I. Ranganathan, M. Ostoja-Starzewski, Universal Elastic Anisotropy Index, Phys. Rev. Lett. 101 (2008) 055504. https://doi.org/10.1103/PhysRevLett.101.055504.
  48. [85]J. Gonzalez-Julian, Processing of MAX phases: From synthesis to applications, J. Am. Ceram. Soc. 104 (2021) 659–690. https://doi.org/10.1111/jace.17544.
  49. [86]A. Otero-De-La-Roza, D. Abbasi-Pérez, V. Luaña, Gibbs2: A new version of the quasiharmonic model code. II. Models for solid-state thermodynamics, features and

Paper details

vlnc:W_hnxn7n4m
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents