betaFeedback

WorksPhysics and Astronomy

ITS3: A truly cylindrical inner tracker for ALICE

Abstract

After the successful installation and first operation of the new Inner Tracking System (ITS2), which consists of about 10 m2^2 of monolithic silicon pixel sensors, ALICE is pioneering the usage of bent, wafer-scale pixel sensors for the ITS3 for Run 4 at the LHC in 2029. Sensors larger than typical reticle sizes can be produced using the technique of stitching. At thicknesses of about 30 μμm, the silicon is flexible enough to be bent to radii of the order of 1 cm. By cooling such sensors with a forced air flow, it becomes possible to construct a detector with minimal material budget. The reduction of the material budget and the improved pointing resolution will allow new measurements, in particular of heavy-flavor decays and electromagnetic probes. Mechanical studies have shown the sensors to be unaffected by bending, and bent sensors have been shown to be fully efficient in test beams. New sensor developments for the ITS3 have shown promising results for fluences even beyond those expected for ITS3.

The current ALICE inner tracking system (ITS2) is the first with monolithic active pixel sensors (MAPS) at the Large Hadron Collider (LHC) at CERN [1]. It consists of 3 inner layers at distances from 22 mm to 42 mm from the interaction point (IP) that have a material budget of only 0.36% X0X_0. The outer tracker consists of 4 layers of MAPS at 194 mm to 395 mm from IP with a material budget of 1.1% X0X_0. It features ALICE PIxel DEtectors (ALPIDEs) [2] with 27 ×\times 29 μm2\mu\mathrm{m}^2 pixels. With 12.5 Gigapixels and 10 square meters active area, it is the largest pixel detector built to date. It has successfully taken data since September 2021.

The upgrade of the ALICE inner tracking system for Run 4

In 2027, it is foreseen to replace the inner barrel layers of ITS2 with new, truly cylindrical bent sensors, the ITS3. A model is shown on the right in Figure 1. The 24120 chips from 200 mm wafers placed at distances down to 22 mm from IP will be replaced with stitched, wafer-scale sensors from 300 mm wafers (see Figure 2) bent in half-cylindrical shapes (see Figure 3), with a minimum radius of the innermost layer of 18 mm from the IP. The material budget will be decreased even further down from 0.36% X0X_0 per layer to about 0.05% X0X_0 per layer, as shown on the right in Figure 3. To improve the proximity to IP, the current beam pipe with an outer radius of 18 mm [4] will be replaced with one of only 16 mm radius and 500 μm\mu\mathrm{m} beryllium corresponding to 0.14% X0X_0.

Figure 1. Left: layout of a monolithic stitched sensor prototype. Right: ITS3 engineering model 1 made of 3 layers of 40-50 μm\mu\mathrm{m} thick dummy silicon. Figure from [3].

A 30 cm pad wafer using stitching

Figure 2. A 30 cm pad wafer using stitching (middle lanes) from engineering run 1.

ITS3 layout and material budget

Figure 3. Left: ITS3 layout with 3 half-layer sensors (green) held in place by carbon foam (gray) and surrounded by a cylindrical support structure (beige). The beam pipe (orange) has 16 mm radius to allow layer 0 to be placed at 18 mm from the interaction point. Right: Material budget in current ALICE ITS2 layer 0. By removing material such as kapton and aluminum for circuit boards, water for cooling, and carbon and glue for mechanical support, wafer-size bent, stitched silicon sensors would result in a material budget of only 0.05% X0X_0 (the bottom yellow area in this graph). Figures from [5].

An example of a pad wafer from one of the chip submissions, engineering run 1 (ER1), that uses stitching on a 30 cm wafer, is shown in Figure 2. In the process of stitching, design blocks are put together during the processing of the silicon. This can make a chip larger than the field of view of the lithographic equipment.

The ALICE ITS3 upgrade for Run 4 will feature 6 half-layer sensors of 26 cm long in the zz direction, two in each layer, that will be thinned to 40-50 μm\mu\mathrm{m}. Each sensor will consist of 3-5 wafer-scale stitched MAPS, with one layer 0 sensor spanning 53.3 mm in rφr\varphi. These will be mechanically held in place by carbon foam. The structure that is foreseen is shown on the left in Figure 3. The new beam pipe will allow to place the ITS3 innermost layer 0 at only 18 mm from the interaction point.

ITS3 requirements and performance

The ITS3 vertex detector has to withstand a fluence resulting from a non-ionizing energy loss of Φeq=1013 1 MeV neq/cm2\Phi_{\mathrm{eq}} = 10^{13}\ 1\ \mathrm{MeV}\ n_{\mathrm{eq}}/\mathrm{cm}^2 and a total ionizing dose of 10 kGy. The particle rates will be up to 2.2 MHz/cm2^2 in the innermost layer for a Pb–Pb interaction rate of 50 kHz.

The ITS3 is expected to improve the tracking efficiency compared to the current vertex detector ITS2, especially at low transverse momentum, as shown on the left in Figure 4. It will also allow a factor of two improvement in the pointing resolution in the rϕr\phi plane over the full range of transverse momenta, as can be seen in the middle of Figure 4. To simulate this, a fast Monte Carlo tool that includes multiple scattering, secondary interactions and detector occupancy was used [5]. This tool ignores the particles’ energy loss in the beampipe and in the detector.

Figure 4. Comparison of the track-reconstruction efficiency (left panel) and pointing resolution in the transverse plane (middle panel) with the current ITS2 and the planned upgrade ITS3 detector using a fast simulation Monte Carlo Tool as well as a full Monte Carlo simulation (circles, middle panel only). Figures from [5]. Right: ratio of the statistical significances expected with the ITS3 and ITS2 for the reconstruction of the Bs0→Ds+π+B_s^0 \rightarrow D_s^+\pi^+ decay in Pb–Pb collisions at sNN=5.5\sqrt{s_{\mathrm{NN}}} = 5.5 TeV. At transverse momenta of around 3 GeV and 14 GeV, the measurement is only possible with the ITS3 upgrade detector.

The comparison of the production yields of strange and non-strange hadrons in the heavy-flavor sector is a necessary measurement to understand heavy-flavor hadronization. In the beauty sector, both ALICE and CMS made first measurements sensitive to the Bs0B_s^0-to-non-strange B meson yield ratio, but the uncertainties prevented to conclude about a possible enhancement with respect to pp collisions [6, 7]. The ITS3 will allow for a large improvement on this measurement as well as for an extension of the measurement to much lower transverse momenta, as shown on the right in Figure 4. The large improvements in tracking, vertexing, and physics performance expected with ITS3 are all results of the reduced pixel pitch, the very close proximity to the interaction point – a mere 18 mm – and the very low material budget.

Reduced material budget

The very low material budget, which contributes to the excellent expected performance of the ITS3 vertex detector, results from removing all the “unnecessary” material in the current ALICE inner tracking system. Circuit boards with kapton and aluminum are, for example, not required if power distribution and data transmission are integrated into the silicon. This is achieved with long, stitched, wafer-scale sensors. These same large-area sensors that are bent around the beam pipe also need less mechanical support, reducing the amount of carbon and glue needed. Finally, if power consumption of these sensors can be kept below 20 mW/cm2^2, water cooling can be replaced by air cooling, further reducing the amount of material budget. Overall, as can be deduced from Figure 3, the material budget per layer of 0.35% X0X_0 for the current ITS2 can be reduced to 0.05% for the ITS3.

To test the concept of air cooling, a setup with a wind tunnel and a laser measurement system has been commissioned, as shown in Figure 5. Mechanical and stability tests are ongoing. The bending of the silicon sensors is studied extensively, with first tests of 40 μ\mum thick “superALPIDEs”, or multiple ALPIDEs from a wafer that were not cut, having proven to show successful bending to 18 mm, as shown in Figure 6. Subsequent beam tests have proven that the ALPIDE in an ITS3 mock-up called the μ\muITS3 with sensors bent to the ITS3 radii of 18, 24, and 30 mm show an efficiency and resolution consistent with flat ALPIDEs [8]. The spatial resolution was also uniform across different radii.

An ALPIDE monolithic active pixel sensor bent by hand and an air-cooling setup at CERN

Figure 5. Left: an ALPIDE monolithic active pixel sensor bent by hand. Right: air cooling is being extensively studied in a commissioned setup at CERN.

Bent “SuperALPIDEs” and bent 65 nm prototype

Figure 6. Bent “SuperALPIDEs” (left), or multiple ALPIDEs that were produced for ITS2 from a single wafer (schematic, middle right). Bending tests have proven to be successful with this chip as well as with regular ALPIDEs bent and studied in beam test facilities. Right: a 65 nm prototype for ITS3 has also been successfully bent and tested.

Sensor R&D

Large-scale wafers of 30 cm and the process of stitching are available in a Tower Partners Semiconductor Co (TPSCo) 65 nm technology. As the ALPIDEs were produced in a 180 nm CMOS imaging process provided by TowerJazz [2], active sensor research and development is ongoing for the new 65 nm technology. There are several submissions planned, and a prototype of a final wafer-scale chip is expected at the end of 2024. Characterization of many small prototypes from a first prototype run on a multi-layer reticle proved operation at room temperature of 20 °C of a digital pixel test structure to be 100% efficient after being irradiated with the ITS3 expected fluence and dose, and operable at 99% efficiency after a fluence of 100 times that of Φeq=1015 1 MeV neq/cm2\Phi_{\mathrm{eq}} = 10^{15}\,\mathrm{1\,MeV}\,n_{\mathrm{eq}}/\mathrm{cm}^{2} [9], as shown in Figure 7. This digital pixel test structure has 32×3232 \times32 pixels of 15 μm15\,\mu\mathrm{m} pitch whose position is time-encoded in an asynchronous digital readout. Charge loss occurs in the corners of a pixel far from the collection electrode, as expected from the very little to no charge sharing. The spatial track resolution was determined to be 2.4 μm2.4\,\mu\mathrm{m}. The first structures bent to a radius of 18 mm, as shown on the right in Figure 6, were successfully tested in the laboratory with an 55Fe{}^{55}\mathrm{Fe} source.

Detection efficiency and fake-hit rate for irradiated and non-irradiated sensors

Figure 7. Detection efficiency and fake-hit rate for non-irradiated sensors and for sensors irradiated with different fluences and dose. This 65 nm digital pixel test structure was shown to be 100% efficient at room temperature after the ITS3 expected radiation load and still operable at 99% efficiency after a fluence of 100 times this expected load. Figure from [9].

The first stitched sensor prototypes are now being investigated. A layout is shown in on the left in Figure 1. There are two different structures, the monolithic stitched sensor (MOSS) of 14×25914 \times259 mm2^{2} with 6.72×1066.72 \times10^{6} pixels, and the monolithic stitched sensor with timing (MOST) of 2.5×2592.5 \times259 mm2^{2} with 0.9×1060.9 \times10^{6} pixels. The full structure for the ITS3 will be 2.5 times as large. Pixels of both 18 and 22.5 μm22.5\,\mu\mathrm{m} pitch are available. The structures will be tested for uniformity and yield.

Summary and outlook

The ALICE collaboration plans the installation of new inner layers (ITS3) in 2027 for the ALICE inner tracking system for LHC Run 4. The aim is to use truly cylindrical wafer-scale monolithic active pixel sensors. Silicon flexibility and bending have been proven with routine tests and a full mock-up of the ITS3 was shown to be efficient when bent to the ITS3 target radii.

For access to wafer-scale stitched sensors, a new 65 nm CMOS imaging technology is used. The first prototypes reach 100% detection efficiency at room temperature at the ALICE ITS3 expected fluence of Φeq=1013 1 MeV neq/cm2\Phi_{\mathrm{eq}} = 10^{13}\ \mathrm{1\ MeV}\ n_{\mathrm{eq}}/\mathrm{cm}^{2}, and the sensor is still operable at room temperature after Φeq=1015 1 MeV neq/cm2\Phi_{\mathrm{eq}} = 10^{15}\ \mathrm{1\ MeV}\ n_{\mathrm{eq}}/\mathrm{cm}^{2}. The first stitched sensors are being tested now. The ITS3 R&D will pave the way to thin, low-power sensors that could be used in future experiments like ALICE3 [10] and will enable a wealth of new precision measurements.

References

  1. [1]CERN Courier 61, no. 4, July/August 2021. https://cerncourier.com/wp-content/uploads/2022/03/CERNCourier2021JulAug-digitaledition.pdf
  2. [2]Gianluca Aglieri Rinella [ALICE Collaboration], “The ALPIDE pixel sensor chip for the upgrade of the ALICE Inner Tracking System”, Nuclear Instruments and Methods in Physics Research Section A, 845, 583-587, 2017, doi:10.1016/j.nima.2016.05.016.DOI
  3. [3]Magnus Mager, DRD7 workshop, 15.03.2023 https://indico.cern.ch/event/1214423/contributions/5285743/.
  4. [4]ALICE Collaboration “ALICE upgrades during the LHC Long Shutdown 2,” [arXiv:2302.01238 [physics.ins-det]].DOI
  5. [5]ALICE Collaboration, “Letter of Intent for an ALICE ITS Upgrade in LS3”, CERN-LHCC-2019-018, LHCC-I-034, 2019, doi:10.17181/CERN-LHCC-2019-018.
  6. [6]ALICE Collaboration, “Measurement of beauty-strange meson production in Pb–Pb collisions at √sNN = 5.02 TeV via non-prompt Dₛ⁺ mesons,” [arXiv:2204.10386 [nucl-ex]].DOI
  7. [7]A.M. Sirunyan et al., [ALICE Collaboration] “Measurement of B⁰ₛ meson production in p-p and Pb-Pb collisions at √sNN = 5.02 TeV” Physics Letters B, 796, 168-190, 2019, doi:10.1016/j.physletb.2019.07.014.
  8. [8]ALICE ITS Project, “First demonstration of in-beam performance of bent Monolithic Active Pixel Sensors”, Nuclear Instruments and Methods in Physics Research Section A, 1028, 166280, 2022, doi:10.1016/j.nima.2021.166280.DOI
  9. [9]G. A. Rinella et al., “Digital Pixel Test Structures implemented in a 65 nm CMOS process,” 2022, doi:10.48550/arXiv.2212.08621.DOI
  10. [10]ALICE Collaboration, “Letter of intent for ALICE 3: A next-generation heavy-ion experiment at the LHC,” arXiv:2211.02491.arxiv.org/abs/2211.02491

Paper details

vlnc:W_j6858q4g
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents