betaFeedback

WorksPhysics and Astronomy

Various Architectures of Colloidal Cu3(MoO4)2(OH)2 and Cu3Mo2O9; Thermal Stability, Photoluminescence and Magnetic Properties of Cu3(MoO4)2(OH)2 and Cu3Mo2O9 Nanosheets

Abstract

The lindgrenite compounds [Cu3(MoO4)2(OH)2] with various architectures and high crystallinity were prepared by a simple surfactant-assisted hydrothermal method. Then, the Cu3Mo2O9 samples were prepared by calcination of the as-synthesized Cu3(MoO4)2(OH)2. The resulting samples have high crystallinity, colloidal properties, high-yield, large-scale production capability with using of nontoxic and inexpensive reagents and water as an environmentally solvent. The scanning electron microscope studies show that the as-prepared lindgrenite nanostructures are well crystallized with rod, sheet and hollow sphere morphologies. Meanwhile, the photoluminescence and magnetic properties of the nanosheet samples have been investigated that the both of Cu3(MoO4)2(OH)2 and Cu3Mo2O9 samples have super paramagnetic behavior at room temperature and in comparison with previous works, Cu3(MoO4)2(OH)2 and Cu3Mo2O9 samples synthesized by the surfactant-assisted hydrothermal method in this work have a very obvious red-shifted PL emission and high intensity.

Corresponding author: Azam Bayat

E-mail address: azam.bayat @modares.ac.ir

Introduction

Molybdenum oxide-based materials, especially binary ones, have been received considerable attention due to their applications in catalysts, display devices, photochromisms, sensors, batteries, absorption, electrical conductivity, magnetism, photochemistry and smart windows [1, 2].

Lindgrenite is one of the rare minerals that originally found in Chile resulting from the oxidation of primary molybdenite [3]. Preparation of natural minerals is useful for verifying the quality of minerals and detection the geological origin of mineral formation. The structural and composition determination of the synthetic mineral crystals may establish the standards for evaluating the quality of the natural minerals. Furthermore, the synthetic approach may facilitate the large-scale production of low-cost, high-quality natural minerals, in particular, those that have technological and economic interest but are rare or impure in nature. Study of the conditions for mineral formation helps mineralogists to explore the minerals in specific zones, where the geological reactions once occurred under the similar circumstance mentioned above [4]. Lindgrenite has been shown to be an effective fire retardant and smoke suppressor when combined with CuSnO3\mathrm{CuSnO}_{3} in polyvinyl chloride plastic (PVC). For this purpose, it seems that the needle-like and the sheet-like structure materials are good candidates for functional polymeric composites and fiber hybrid materials [5, 6, 7].

On the other hand, the properties of Cu3Mo2O9\mathrm{Cu}_{3}\mathrm{Mo}_{2}\mathrm{O}_{9} have attracted extensive interests in various research fields [1]. Molybdenum trioxide nanostructures can be used as catalysts. For instance, Cu3Mo2O9\mathrm{Cu}_{3}\mathrm{Mo}_{2}\mathrm{O}_{9} is employed in the deep oxidation of diesel exhaust soot with high activity, but reports on Cu3Mo2O9\mathrm{Cu}_{3}\mathrm{Mo}_{2}\mathrm{O}_{9} morphologies are very few [2, 8].

Shores et al. have reported the synthesis of lindgrenite elegantly modified by bipyridine and piperazine. The two ditopic ligands, interestingly, break the inorganic 3D network into layers, consequently transforming the ferromagnetic lindgrenite into antiferromagnets. Vilminot et al. presented the hydrothermal synthesis of the hydrogenated and deuterated analogues of lindgrenite [9]. Bao et al. synthesized Cu3(MoO4)2(OH)2\mathrm{Cu}_{3}(\mathrm{MoO}_{4})_{2}(\mathrm{OH})_{2} which could be transferred to metastable Cu3Mo2O9\mathrm{Cu}_{3}\mathrm{Mo}_{2}\mathrm{O}_{9} by thermal decomposition. Xu et al. prepared Cu3Mo2O9\mathrm{Cu}_{3}\mathrm{Mo}_{2}\mathrm{O}_{9} with hollow and prickly sphere-like architecture by a simple thermal treatment of lindgrenite. Also, Jiang et al. synthesized lindgrenite nanocrystals by simple aqueous precipitation, which could be decomposed to Cu3Mo2O9\mathrm{Cu}_{3}\mathrm{Mo}_{2}\mathrm{O}_{9}. Hasan et al. synthesized Cu3Mo2O9\mathrm{Cu}_{3}\mathrm{Mo}_{2}\mathrm{O}_{9} for catalytic oxidation of the harmful gases and Zhang et al. prepared Cu3Mo2O9\mathrm{Cu}_{3}\mathrm{Mo}_{2}\mathrm{O}_{9} nanosheets by a hydrothermal method and investigate the direct electrochemistry of hemoglobin (Hb). Finally, Xia et al. constructed Cu3Mo2O9\mathrm{Cu}_{3}\mathrm{Mo}_{2}\mathrm{O}_{9} nanoplates with excellent lithium storage properties based on a pH-dependent dimensional change [1, 10].

In this work, by a hydrothermal surfactant-assisted method, the colloidal Cu3(MoO4)2(OH)2\mathrm{Cu}_{3}(\mathrm{MoO}_{4})_{2}(\mathrm{OH})_{2} and Cu3Mo2O9\mathrm{Cu}_{3}\mathrm{Mo}_{2}\mathrm{O}_{9} nanorods, nanosheets and self-assembled hallow spheres with high crystallinity were synthesized. A significant feature of this synthetic approach was pointed out that the resulting samples have high crystallinity, hydrophilic surface, high-yield, large-scale production capability with using of nontoxic and inexpensive reagents and water as an environmentally benign reaction solvent. For use these nanostructures in applied sciences it is must to disperse or soluble in water and the solubility/dispersibility of the samples plays a key role in their applications. The size and shape of the as-synthesized samples can be controlled readily by simple tuning the reaction parameters and the reaction parameters play a major role in the morphologies of the final samples. Meanwhile, possible growth mechanisms for the formation of single-crystalline Cu3(MoO4)2(OH)2\mathrm{Cu}_{3}(\mathrm{MoO}_{4})_{2}(\mathrm{OH})_{2} products were proposed. Moreover, the photoluminescence and magnetic properties of the as-synthesized Cu3(MoO4)2(OH)2\mathrm{Cu}_{3}(\mathrm{MoO}_{4})_{2}(\mathrm{OH})_{2} and Cu3Mo2O9\mathrm{Cu}_{3}\mathrm{Mo}_{2}\mathrm{O}_{9} nanosheets were determined in which a red emission was observed at 706 nm by excitation at 237 nm in their photoluminescence spectra of the Cu3(MoO4)2(OH)2\mathrm{Cu}_{3}(\mathrm{MoO}_{4})_{2}(\mathrm{OH})_{2} and Cu3Mo2O9\mathrm{Cu}_{3}\mathrm{Mo}_{2}\mathrm{O}_{9} at room temperature. Also, the results of the magnetic properties investigation of the Cu3(MoO4)2(OH)2\mathrm{Cu}_3(\mathrm{MoO}_4)_2(\mathrm{OH})_2 and Cu3Mo2O9\mathrm{Cu}_3\mathrm{Mo}_2\mathrm{O}_9 nanosheet samples showed that these nanosheet samples have super paramagnetic behavior at room temperature. Nanosheet morphology possess a unique feature of two-dimensional anisotropy and due to trigger quantum confinement effects hence gaining new physiochemical properties. This morphology has important applications in the field of energy conversion, storage devices, biological sensors, electronics, ferromagnetic, magneto-optical, electrochemical, photo-responsive, flexible electrochromic devices, biotechnology, water splitting, catalysis, gas sensing, and energy storage due to their unique electric properties and high packing densities [11, 12, 13, 14, 15].

Experimental Section

Materials and Apparatus

All of the raw materials used in this research except Cu(NO3)2⋅3H2O\mathrm{Cu(NO_3)_2\cdot3H_2O} (Panreac) were purchased from Merck company. The structure and phase purity of as-synthesized samples was characterized by powder X-ray diffraction (XRD) on a Philips X’pert X-ray diffractometer using Cu Kα\alpha radiation (wavelength, λ=1.5418\lambda= 1.5418 Å). Fourier transform infrared (FT-IR) spectra of samples were recorded on a Shimadzu-8400S spectrometer in the range of 400–4000 cm−1\mathrm{cm}^{-1} using KBr pellets. The scanning electron microscopy (SEM) analysis of lindgrenite (Cu3(MoO4)2(OH)2\mathrm{Cu}_3(\mathrm{MoO}_4)_2(\mathrm{OH})_2) and Cu3Mo2O9\mathrm{Cu}_3\mathrm{Mo}_2\mathrm{O}_9 were recorded by TESCAN (VEGA3) instrument. Thermogravimetric analysis (TGA) and differential thermal analysis (DTA) were performed on a STA 504, the atmosphere was air. Photoluminescence (PL) spectra of the nanosheet samples were recorded on a JASCO FP-6500 spectrofluorometer at room temperature. Finally, the magnetic properties of the nanosheet samples were measured at room temperature using a vibrating sample magnetometer (VSM; Meghnatis Kavir Kashan Co., Kashan, Iran) in a maximum applied field of 15 k Oe.

Synthesis of Cu3(MoO4)2(OH)2\mathrm{Cu}_{3}(\mathrm{MoO}_{4})_{2}(\mathrm{OH})_{2} Nanorods

For the synthesis of lindgrenite nanorods, Cu(NO3)2⋅3H2O\mathrm{Cu}(\mathrm{NO}_{3})_{2}\cdot3\mathrm{H}_{2}\mathrm{O} (0.42 g, 1.74 mmol), Na2MoO4⋅2H2O\mathrm{Na}_{2}\mathrm{MoO}_{4}\cdot2\mathrm{H}_{2}\mathrm{O} (0.28 g, 1.16 mmol) and 6-aminohexanoic acid (0.46 g, 3.51 mmol) were dissolved in 140 mL distilled water. The mixture was stirred for 10 min at room temperature. Precipitates were produced immediately from the combination of the metal cation (Cu2+\mathrm{Cu}^{2+}) and molybdate anion (MoO42−\mathrm{MoO}_{4}^{2-}) in pH of 5, the initial pH of solution. The resulting reaction mixture (140 mL) was transferred to 200 mL Teflon-lined stainless steel autoclave and treated to 180 °C for 20 h. The obtained sample were filtered out and washed with distilled water, and dried at 60 °C for 2 h or more.

Synthesis of Cu3(MoO4)2(OH)2\mathrm{Cu}_{3}(\mathrm{MoO}_{4})_{2}(\mathrm{OH})_{2} Nanosheets

Moreover, for the synthesis of lindgrenite nanosheets, Cu(NO3)2⋅3H2O\mathrm{Cu}(\mathrm{NO}_{3})_{2}\cdot3\mathrm{H}_{2}\mathrm{O} (0.23 g, 0.96 mmol) and 6-aminohexanoic acid (0.50 g, 3.84 mmol) were dissolved in 63 mL distilled water. A 0.03 M aqueous solution of sodium molybdate (63 mL) was added to the above solution at room temperature under stirring for 10 min. The resulting reaction mixture (126 mL) was transferred to 220 mL Teflon-lined stainless steel autoclave and treated to 180 °C for 20 h. The obtained sample were filtered out and washed with distilled water, and dried at 60 °C for 2 h or more.

Synthesis of Cu3(MoO4)2(OH)2\mathrm{Cu}_{3}(\mathrm{MoO}_{4})_{2}(\mathrm{OH})_{2} Hollow Spheres

Finally, for the synthesis of lindgrenite hollow spheres, Cu(NO3)2⋅3H2O\mathrm{Cu}(\mathrm{NO}_{3})_{2}\cdot3\mathrm{H}_{2}\mathrm{O} (0.42 g, 1.74 mmol) and 6-aminohexanoic acid (0.46 g, 3.51 mmol) were dissolved in 57 mL distilled water. A 0.015 M aqueous solution of sodium molybdate (57 mL) was added to the above solution at room temperature under stirring for 10 min. The resulting reaction mixture (114 mL) was transferred to 200 mL Teflon-lined stainless steel autoclave and treated to 60 °C for 20 h. The obtained sample were filtered out and washed with distilled water, and dried at 60 °C for 2 h or more.

Synthesis of Cu3Mo2O9\mathrm{Cu}_{3}\mathrm{Mo}_{2}\mathrm{O}_{9} with Various Architectures

For the synthesis of Cu3Mo2O9\mathrm{Cu}_{3}\mathrm{Mo}_{2}\mathrm{O}_{9} with various architectures, the as-synthesized Cu3(MoO4)2(OH)2\mathrm{Cu}_{3}(\mathrm{MoO}_{4})_{2}(\mathrm{OH})_{2} samples directly calcined in a furnace at calcination temperature of 500 °C, in air for 4 h with heating rate of 10 °C min−1^{-1}.

Results and Discussion

Structure and Morphology of Cu3(MoO4)2(OH)2\mathrm{Cu}_{3}(\mathrm{MoO}_{4})_{2}(\mathrm{OH})_{2}

The structure of lindgrenite is composed of the of Cu3(OH)2\mathrm{Cu}_{3}(\mathrm{OH})_{2} ribbons of the brucite structure consisting of edge-sharing copper octahedra with two kinds of copper atoms, Cu(1) and Cu(2), both having distorted octahedral coordination of oxygen atoms, running parallel to the cc axis. MoO4\mathrm{MoO}_{4} connects three ribbons together via its oxygen atoms: O(1) and O(3) are bonded to single Cu atoms, while O(2) and O(4) bridges two copper atoms each on two adjacent chains [16]. Fig. 1 shows the XRD patterns of lindgrenite samples prepared by hydrothermal surfactant-assisted synthesis. Lindgrenite (Cu3(MoO4)2(OH)2\mathrm{Cu}_{3}(\mathrm{MoO}_{4})_{2}(\mathrm{OH})_{2}) crystallizes in a monoclinic system with the space group of P21/nP2_{1}/n (No. 14) [16]. Diffraction patterns of all Cu3(MoO4)2(OH)2\mathrm{Cu}_{3}(\mathrm{MoO}_{4})_{2}(\mathrm{OH})_{2} samples are wellindexed to the monoclinic phase structure, and they are in accordance with the JCPDS card no. 75-1438 (Fig. 1). The intense diffractions in patterns without any other peaks indicate the high purity and well crystallinity of samples. The eight primary reflections; 12.62°, 20.42°,21.34°, 24.85°, 25.34°, 25.42°, 25.62° and 33.43° are indexed as (020), (021), (101), (121), (130), (040), (111) and (141) of Cu3(MoO4)2(OH)2\mathrm{Cu}_3(\mathrm{MoO}_4)_2(\mathrm{OH})_2, respectively, and they are in agreement with the data reported in literature [17].

Image not extracted

Figure 1.

The FTIR spectra of the colloidal Cu3(MoO4)2(OH)2\mathrm{Cu}_3(\mathrm{MoO}_4)_2(\mathrm{OH})_2 samples are shown in Fig. 2a-c. The bands at about 800-1000 cm−1\mathrm{cm}^{-1} are ascribed to MoO42−\mathrm{MoO}_4^{2-} stretching vibration, and it is consistent with the reported values [9]. The band at about 450 cm−1\mathrm{cm}^{-1} is assigned to the bending vibration of Cu-O. Also, the weak absorptions at about 1600 cm−1\mathrm{cm}^{-1} and the bands at 3000 –3600 cm−1\mathrm{cm}^{-1} demonstrate the bending and the stretching vibrations of H2O\mathrm{H}_2\mathrm{O} and O-H, respectively [18, 19]. Bands at about 2800-2900 cm−1\mathrm{cm}^{-1} attributed to the C-H stretching vibrations of methylene groups of the AHA molecules which have been overlapped with the stretching vibration of H2O\mathrm{H}_2\mathrm{O} bands, and bands at about 1400 cm−1\mathrm{cm}^{-1} correspond to C-N bending modes of AHA molecules. Meanwhile, Bands at about 3400 cm−1\mathrm{cm}^{-1} correspond to -NH2_2 stretching mode of AHA molecules [20, 21, 22, 23]. These results demonstrate that the carboxylic (-COOH) terminus are free and thus, approve hydrophilicity of the three samples.

Image not extracted

Figure 2.

The morphologies of as-prepared products were also examined by SEM (Fig. 3). Fig. 3a-b show SEM images of the prepared Cu3(MoO4)2(OH)\mathrm{Cu}_3(\mathrm{MoO}_4)_2(\mathrm{OH}), having rod morphology with diameters of about 100 nm. Fig. 3c-e show SEM image of the Cu3(MoO4)2(OH)2\mathrm{Cu}_{3}(\mathrm{MoO}_{4})_{2}(\mathrm{OH})_{2} prepared with a 0.03 M aqueous solution of sodium molybdate, at 180 °C. As Figures show the as-synthesized sample have sheet forms with the sizes of 30−100 nm in width. The SEM observation also indicates that almost 100% of the obtained Cu3(MoO4)2(OH)2\mathrm{Cu}_{3}(\mathrm{MoO}_{4})_{2}(\mathrm{OH})_{2} sample are super thin sheet and no other type of particles is visible. Fig. 3f shows SEM image of the Cu3(MoO4)2(OH)2\mathrm{Cu}_{3}(\mathrm{MoO}_{4})_{2}(\mathrm{OH})_{2} prepared with a 0.015 M aqueous solution of sodium molybdate, at 60 °C in which the as-synthesized sample have hallow sphere architecture. The mean diameter of these hallow spheres were about 25 μ\mum as shown in Fig. 3g. Moreover, SEM image of the Cu3(MoO4)2(OH)2\mathrm{Cu}_{3}(\mathrm{MoO}_{4})_{2}(\mathrm{OH})_{2} hallow spheres demonstrate which an individual hallow sphere is composed of a large number of nanosheets with a thickness of about 40-70 nm (Fig. 3h). Also, the SEM observation shows that the spheres have hollow structures (Fig. 3i)

Image not extracted

Figure 3.

Possible Growth Mechanism of Cu3(MoO4)2(OH)2\mathrm{Cu}_{3}(\mathrm{MoO}_{4})_{2}(\mathrm{OH})_{2} with Various Architectures

For Cu3(MoO4)2(OH)2\mathrm{Cu}_{3}(\mathrm{MoO}_{4})_{2}(\mathrm{OH})_{2} nanorods, purposed mechanism based on literature reports, involves two mechanisms well known as Ostwald ripening and oriented attachment [24, 25]. When Cu(NO3)2⋅3H2O\mathrm{Cu}(\mathrm{NO}_{3})_{2}\cdot3\mathrm{H}_{2}\mathrm{O} solution was added to the MoO42−\mathrm{MoO}_{4}^{2-} solution in the presence of 6-aminohexanoic acid, Cu(OH)2\mathrm{Cu}(\mathrm{OH})_{2} formed firstly. Then Cu(OH)2\mathrm{Cu}(\mathrm{OH})_{2} combined with copper ions and MoO42−\mathrm{MoO}_{4}^{2-} and a high supersaturation degree will be reached, and amorphous Cu3(MoO4)2(OH)2\mathrm{Cu}_{3}(\mathrm{MoO}_{4})_{2}(\mathrm{OH})_{2} particles will form immediately. This process is described in Equations (1) and (2) [26].

Cu2++2OH−→Cu(OH)2(1)\mathrm{Cu}^{2+} + 2\mathrm{OH}^{-} \rightarrow\mathrm{Cu}(\mathrm{OH})_{2} \tag*{(1)}
Cu(OH)2+2Cu2++2MoO42−→Cu3(MoO4)2(OH)2(2)\mathrm{Cu}(\mathrm{OH})_{2} + 2\mathrm{Cu}^{2+} + 2\mathrm{MoO}_{4}^{2-} \rightarrow\mathrm{Cu}_{3}(\mathrm{MoO}_{4})_{2}(\mathrm{OH})_{2} \tag*{(2)}

When the synthesis temperature was increased, monodisperse spherical nanoparticles were obtained. At a longer reaction time, the equilibrium of growth kinetics was observed and at higher reaction temperature, according to the well-known Ostwald ripening process, a mixture of spherical particles and primary rod-like particles were observed and finally, with the temperature increasing of the reaction no nanoparticles were observed. At elevated temperature, the nanorods involved thicker and longer colloidal nanorods. At this stage, the oriented attachment is dominant mechanism [24].

On the other hand, for Cu3(MoO4)2(OH)2\mathrm{Cu}_3(\mathrm{MoO}_4)_2(\mathrm{OH})_2 nanosheets, based on literature reports [27, 28], was considered that the molybdate nanosheets formation can be the effect of among Ostwald ripening [29], lateral-aggregation [24], and dissolution/recrystallization [27] processes. Probably, this is due to the presence of 6-aminohexanoic acid molecules in the water medium. Similar to rod morphology, when Cu(NO3)2⋅3H2O\mathrm{Cu}(\mathrm{NO}_3)_2\cdot3\mathrm{H}_2\mathrm{O} solution was added to the MoO42−\mathrm{MoO}_4^{2-} solution in the presence of 6-aminohexanoic acid, Cu(OH)2\mathrm{Cu}(\mathrm{OH})_2 formed firstly. Then Cu(OH)2\mathrm{Cu}(\mathrm{OH})_2 combined with copper ions and MoO42−\mathrm{MoO}_4^{2-} and a high supersaturation degree will be reached, and amorphous Cu3(MoO4)2(OH)2\mathrm{Cu}_3(\mathrm{MoO}_4)_2(\mathrm{OH})_2 particles will form immediately. Apparently, the interesting transformation of a small crystalline nucleus into lindgrenite nanoparticles in a supersaturated solution at elevated temperature, proceed through the process known as Ostwald ripening. Subsequently, the primary nanoparticles quickly transform into lindgrenite nanosheets through the lateral-aggregation mechanism. At the end of the synthetic process, the shape transformation of the crystallized nanosheets often operates through a standard dissolution-recrystallization mechanism. Thus, possible growth mechanism of the Cu3(MoO4)2(OH)2\mathrm{Cu}_3(\mathrm{MoO}_4)_2(\mathrm{OH})_2 nanosheets was dominated by crystallization-dissolution-recrystallization mechanism.

For self-assembled Cu3(MoO4)2(OH)2\mathrm{Cu}_3(\mathrm{MoO}_4)_2(\mathrm{OH})_2 hollow sphere sample, after formation of the subunit nanosheets via the purposed mechanism for lindgrenite nanosheets, the assembly mechanism of sphere-like architecture operate. Therefore, possible growth mechanism of the Cu3(MoO4)2(OH)2\mathrm{Cu}_3(\mathrm{MoO}_4)_2(\mathrm{OH})_2 hollow sphere morphology was dominated by crystallization-dissolution-recrystallization- self-assembly growth mechanism.

Structure and Morphology of Cu3Mo2O9\mathrm{Cu}_3\mathrm{Mo}_2\mathrm{O}_9

Tertiary copper molybdate, Cu3Mo2O9\mathrm{Cu}_3\mathrm{Mo}_2\mathrm{O}_9, have an orthorhombic structure with space group PnmaPnma. In the unit cell of this material two types of Mo–4O tetrahedra, one compressed Cu-6O octahedral, and two types of Cu-5O polyhedral exist. The catalytic properties of this metal oxide are closely related to metal-oxygen bonds [2].

XRD patterns of the obtained Cu3Mo2O9\mathrm{Cu}_3\mathrm{Mo}_2\mathrm{O}_9 with various architectures at calcination temperature of 500 °C are shown in Fig. 4a-c. Diffraction patterns of the three Cu3Mo2O9\mathrm{Cu}_3\mathrm{Mo}_2\mathrm{O}_9 samples are well-indexed to the orthorhombic structure, and they are in accordance with the standard diffraction patterns of Cu3Mo2O9\mathrm{Cu}_3\mathrm{Mo}_2\mathrm{O}_9, the JCPDS card no. 70-2493.

Image not extracted

Figure 4.

The FTIR spectra of the colloidal Cu3Mo2O9\mathrm{Cu}_3\mathrm{Mo}_2\mathrm{O}_9 samples are shown in Fig. 5a-c. Due to the difference of Cu–O and Mo–O bands in the crystal structures of Cu3(MoO4)2(OH)2\mathrm{Cu}_3(\mathrm{MoO}_4)_2(\mathrm{OH})_2 and Cu3Mo2O9\mathrm{Cu}_3\mathrm{Mo}_2\mathrm{O}_9, in the spectra of Cu3Mo2O9\mathrm{Cu}_3\mathrm{Mo}_2\mathrm{O}_9 samples, the excess bands were appeared in the range of 400–1300 cm−1^{-1} [30, 31, 32]. The bands at 530 cm−1^{-1} is assigned to the bending vibration of Cu−O. Also, the absorptions at 1600 cm−1^{-1} and the bands at 3000 –3700 cm−1^{-1} demonstrate the bending and the stretching vibrations of H2_2O and O-H, respectively [18, 19]. Bands at about 2800-2900 cm−1\mathrm{cm}^{-1} attributed to the C-H stretching vibrations of methylene groups of the AHA molecules and band at about 1400 cm−1\mathrm{cm}^{-1} correspond to C-N bending modes of AHA molecules, respectively.

Bands at about 3400 cm−1\mathrm{cm}^{-1} correspond to -NH2_2 stretching mode of AHA molecules which have been overlapped with the stretching vibration of O-H bands [20, 21, 22, 23]. These results approve hydrophilicity of the three samples. As seen in Fig. 2, comparing with the bands of O-H stretching modes in Cu3_3Mo2_2O9_9 samples, due to the existence of hydrogen bond in the lindgrenite crystal lattice, the bands of O-H stretching modes in Cu3_3(MoO4_4)2_2(OH)2_2 samples have shifted to the lower wavenumbers and split into two bands.

Image not extracted

Figure 5.

SEM images of the Cu3_3Mo2_2O9_9 samples obtained at calcination temperature of 500 °C, are shown in Fig. 6. SEM image of the Cu3_3Mo2_2O9_9 obtained from calcined Cu3_3(MoO4_4)2_2(OH)2_2 nanorod sample is shown in Figure 6a (PDF p. 26). As Figure shows the as-synthesized sample have rod forms with diameters of about 100 nm. Also, SEM image of the Cu3_3Mo2_2O9_9 obtained from calcined Cu3_3(MoO4_4)2_2(OH)2_2 nanosheet sample is shown in Figure 6b (PDF p. 26)-Figure 6c (PDF p. 26). This sample has retained the morphology of the lindgrenite nanosheet sample with the sizes of 20–100 nm in thickness. Finally, for Cu3_3Mo2_2O9_9 hollow sphere sample, calcined at 500 °C, the morphology of the lindgrenite hollow sphere sample has been retained with the same size in diameter of hollow sphere and nanosheet thickness, contributing in hollow sphere structure, as shown in Figure 6d (PDF p. 26)-Figure 6e (PDF p. 26).

Image not extracted

Figure 6.

Thermal Stability of Cu3(MoO4)2(OH)2\mathrm{Cu}_3(\mathrm{MoO}_4)_2(\mathrm{OH})_2 and Cu3Mo2O9\mathrm{Cu}_3\mathrm{Mo}_2\mathrm{O}_9 Nanosheets

In order to investigation of the thermal stability of Cu3(MoO4)2(OH)2\mathrm{Cu}_3(\mathrm{MoO}_4)_2(\mathrm{OH})_2 and Cu3Mo2O9\mathrm{Cu}_3\mathrm{Mo}_2\mathrm{O}_9, TG-DTA curves obtained under a flow of air as shown in Fig. 7. According to thermogravimetry (TG) analysis, the weight loss consists of two distinct steps. In the first stage, the TG curve indicated a weight loss (about 3.41 Wt%) between 50 °C and 450 °C, corresponding to the loss of adsorbed water and coordinated water [33] and elimination of OH groups as H2O\mathrm{H}_2\mathrm{O}, result in the formation of Cu3Mo2O9\mathrm{Cu}_3\mathrm{Mo}_2\mathrm{O}_9. Meanwhile, weight-loss step in the range of 135 to 450 °C, corresponding to combustion of 6-aminohexanoic acid of Cu3(MoO4)2(OH)2\mathrm{Cu}_3(\mathrm{MoO}_4)_2(\mathrm{OH})_2 surface [34]. A second weight loss observed between 700 °C and 800 °C, corresponding to the decomposition of Cu3Mo2O9\mathrm{Cu}_3\mathrm{Mo}_2\mathrm{O}_9. The three endothermic peaks in DTA curve at 171 °C, 384 °C and 387 °C are assigned to the loss of adsorbed water, coordinated water and 6-aminohexanoic acid of Cu3(MoO4)2(OH)2\mathrm{Cu}_3(\mathrm{MoO}_4)_2(\mathrm{OH})_2, respectively. Finally, significant endothermic peak at 780 °C resulted from decomposition of Cu3Mo2O9\mathrm{Cu}_3\mathrm{Mo}_2\mathrm{O}_9.

Image not extracted

Figure 7.

Photoluminescence Properties of Cu3(MoO4)2(OH)2\mathrm{Cu}_3(\mathrm{MoO}_4)_2(\mathrm{OH})_2 Nanosheets

According to the earlier reports, Cu3(MoO4)2(OH)2\mathrm{Cu}_3(\mathrm{MoO}_4)_2(\mathrm{OH})_2 has the monoclinic structure with space group P21/n\mathrm{P}2_1/n and its crystal structure consists of strips of edge-sharing CuO6\mathrm{CuO}_6 octahedral that are cross-linked by MoO42−\mathrm{MoO}_4^{2-} tetrahedral [3]. The MoO42−\mathrm{MoO}_4^{2-} tetrahedral is represented as ΓTd=A1(ν1)+E(ν2)+F2(ν3)+F2(ν4)\Gamma_{\mathrm{Td}} = A_1(\nu_1) + E(\nu_2) + F_2(\nu_3) + F_2(\nu_4) in which A1(ν1)A_1(\nu_1) and E(ν2)E(\nu_2) are Raman active, but F2(ν3)F_2(\nu_3) and F2(ν4)F_2(\nu_4) are infrared active. Since the F2(ν3)F_2(\nu_3) vibrations are antisymmetric stretches, the bands at about 800 cm−1\mathrm{cm}^{-1} are assigned to F2(ν3)F_2(\nu_3) antisymmetric stretching vibrations of Cu3(MoO4)2(OH)2\mathrm{Cu}_3(\mathrm{MoO}_4)_2(\mathrm{OH})_2. In this study, all samples exhibit the same bands at about 813 cm−1\mathrm{cm}^{-1}. This band could be originated from the Mo-O stretching vibration of the MoO4\mathrm{MoO}_4 group [35].

Fig. 8 shows the room-temperature photoluminescence spectrum of the as-prepared Cu3(MoO4)2(OH)2\mathrm{Cu}_{3}(\mathrm{MoO}_{4})_{2}(\mathrm{OH})_{2} nanosheetss using the excitation wavelength of 237 nm. The spectrum shows that Lindgrenite nanosheets exhibited emission peaks at 705 nm which could be due to the charge-transfer transitions within the MoO42−\mathrm{MoO}_{4}^{2-} complex [36, 37, 38, 39, 40]. Compared with earlier results, Cu3(MoO4)2(OH)2\mathrm{Cu}_{3}(\mathrm{MoO}_{4})_{2}(\mathrm{OH})_{2} sample that synthesized in this work by the surfactant-assisted hydrothermal method has a very obvious red-shifted PL emission. It is well known that the differences of maximum emission wavelengths can be assigned to the structural organization levels, preparation methods, treatment conditions, and different excitation wavelengths and the relative intensity of the emission peaks closely related to the morphology, size, surface defect states, and so on [41, 42]. Generally, these results indicate that high crystalline hydrophilic surfaced Cu3(MoO4)2(OH)2\mathrm{Cu}_{3}(\mathrm{MoO}_{4})_{2}(\mathrm{OH})_{2} nanosheets prepared in this work have potential as a photoluminusent material.

Image not extracted

Figure 8.

Magnetic Properties of Cu3(MoO4)2(OH)2\mathrm{Cu}_{3}(\mathrm{MoO}_{4})_{2}(\mathrm{OH})_{2} Nanosheets

The magnetization of our Cu3(MoO4)2(OH)2\mathrm{Cu}_{3}(\mathrm{MoO}_{4})_{2}(\mathrm{OH})_{2} nanosheets sample obtained by surfactant-assisted hydrothermal method as a function of magnetic field at the maximum field of 10 kOe is shown in Fig. 9. The magnetization of this sample is not completely saturated yet at the maximum field of the measurements (10 kOe). Hysteresis loops at room temperature are much thin and reveal that the as-synthesized Cu3(MoO4)2(OH)2\mathrm{Cu}_{3}(\mathrm{MoO}_{4})_{2}(\mathrm{OH})_{2} nanosheets exhibits zero coercivity and, thus, have superparamagnetic at room temperature.

Image not extracted

Figure 9.

Photoluminescence Properties of Cu3_3Mo2_2O9_9 Nanosheets

According to the earlier reports, Cu3_3Mo2_2O9_9 has an orthorhombic structure with space group Pnma\mathit{Pnma} and in the unit cell of this material exists two types of Mo-4O tetrahedral [2]. Fig. 10 shows the room-temperature photoluminescence spectrum of the as-prepared Cu3_3Mo2_2O9_9 nanosheets using the excitation wavelength of 237 nm. The spectrum shows that nanosheets exhibited emission peaks at 706 nm which could be due to the charge-transfer transitions within the MoO42−\mathrm{MoO}_{4}^{2-} complex [36, 37, 38, 39, 40]. The as-synthesized Cu3_3Mo2_2O9_9 sample by the surfactant-assisted hydrothermal method also has a very obvious red-shifted PL emission. Generally, these results indicate that Cu3_3Mo2_2O9_9 nanosheets prepared in this work similar to high crystalline hydrophilic surfaced Cu3(MoO4)2(OH)2_3(\mathrm{MoO}_{4})_{2}(\mathrm{OH})_{2} nanosheets have potential as a photoluminusent material.

Image not extracted

Figure 10.

Magnetic Properties of Cu3_3Mo2_2O9_9 Nanosheets

The magnetization of as-prepared Cu3_3Mo2_2O9_9 nanosheet sample at calcination temperature of 500 °C as a function of magnetic field is shown in Fig. 11. The magnetization of this sample is not completely saturated yet at the maximum field of the measurements (15 kOe). Hysteresis loops at room temperature are much thin and reveal that the as-synthesized sample exhibits zero coercivity and, thus, have superparamagnetic at room temperature. Moreover, the saturation magnetization MsM_s of as-synthesized Cu3_3Mo2_2O9_9 is higher than as-synthesized Cu3(MoO4)2(OH)2_3(\mathrm{MoO}_{4})_{2}(\mathrm{OH})_{2} at room temperature.

Image not extracted

Figure 11.

Conclusion

In this study, well-crystalline monoclinic Cu3(MoO4)2(OH)2\mathrm{Cu}_3(\mathrm{MoO}_4)_2(\mathrm{OH})_2 and orthorhombic Cu3Mo2O9\mathrm{Cu}_3\mathrm{Mo}_2\mathrm{O}_9 nanostructures have been prepared via a simple and green route. This method is highly scale up able. The results demonstrated that well crystallized lindgrenite samples have rod morphology with diameters of about 100 nm, sheet form with thickness of 30–100 nm and hallow sphere shape, consisting of a large number of nanosheets with thickness of about 40-70 nm. The fabricated Cu3Mo2O9\mathrm{Cu}_3\mathrm{Mo}_2\mathrm{O}_9 samples from thermal treatment of lindgrenite retained the original morphologies. Furthermore, possible mechanisms for the formation of hydrophilic-surfaced Cu3(MoO4)2(OH)2\mathrm{Cu}_3(\mathrm{MoO}_4)_2(\mathrm{OH})_2 crystals is proposed. Possible proposed mechanisms of the Cu3(MoO4)2(OH)2\mathrm{Cu}_3(\mathrm{MoO}_4)_2(\mathrm{OH})_2 with various architectures, were dominated by Ostwald ripening-oriented attachment, crystallization-dissolution-recrystallization and crystallization-dissolution-recrystallization-self-assembly growth mechanisms for nanorod, nanosheet and hollow sphere morphologies, respectively. Meanwhile, the photoluminescence and magnetic properties of the nanosheet samples have been investigated that the both of Cu3(MoO4)2(OH)2\mathrm{Cu}_3(\mathrm{MoO}_4)_2(\mathrm{OH})_2 and Cu3Mo2O9\mathrm{Cu}_3\mathrm{Mo}_2\mathrm{O}_9 samples have super paramagnetic behavior at room temperature and in comparison with previous works, Cu3(MoO4)2(OH)2\mathrm{Cu}_3(\mathrm{MoO}_4)_2(\mathrm{OH})_2 and Cu3Mo2O9\mathrm{Cu}_3\mathrm{Mo}_2\mathrm{O}_9 samples synthesized by the surfactant-assisted hydrothermal method in this work have a very obvious red-shifted PL emission and high intensity.

Acknowledgment. The authors acknowledge finical support of Tarbiat Modares University and Shahid Beheshti University for supporting this work.

Fig. Captions

Image not extracted

Figure 1 (PDF p. 19). XRD patterns for the Cu3(MoO4)2(OH)2\mathrm{Cu}_3(\mathrm{MoO}_4)_2(\mathrm{OH})_2 samples with (a) rod, (b) sheet and (c) hollow spherical shapes.

Image not extracted

Figure 2 (PDF p. 19). Infrared spectra of the as-prepared colloidal Cu3(MoO4)2(OH)2\mathrm{Cu}_3(\mathrm{MoO}_4)_2(\mathrm{OH})_2 with various architectures: (a) rod, (b) sheet and (c) hollow sphere morphology.

Image not extracted

Figure 3 (PDF p. 19). SEM images of (a-b) Cu3(MoO4)2(OH)2\mathrm{Cu}_3(\mathrm{MoO}_4)_2(\mathrm{OH})_2 rod-shaped structure, (c-e) Cu3(MoO4)2(OH)2\mathrm{Cu}_3(\mathrm{MoO}_4)_2(\mathrm{OH})_2 sheet form structure, (f-i) Cu3(MoO4)2(OH)2\mathrm{Cu}_3(\mathrm{MoO}_4)_2(\mathrm{OH})_2 hollow spherical shape.

Image not extracted

Figure 4 (PDF p. 19). XRD patterns of the Cu3Mo2O9\mathrm{Cu}_3\mathrm{Mo}_2\mathrm{O}_9 samples calcined at 500 ∘C500\,^\circ\mathrm{C} with (a) rod, (b) sheet and (c) hollow sphere morphologies.

Image not extracted

Figure 5 (PDF p. 19). Infrared spectra of the colloidal Cu3Mo2O9\mathrm{Cu}_3\mathrm{Mo}_2\mathrm{O}_9 nanostructures: (a) rod, (b) sheet and (c) hollow sphere morphology.

Image not extracted

Figure 6 (PDF p. 19). SEM images of the colloidal Cu3Mo2O9\mathrm{Cu}_3\mathrm{Mo}_2\mathrm{O}_9 (a) nanorods, (b-c) nanosheets and (d-e) hollow spheres.

Fig. 7. TAG and DTA analysis of the prepared Cu3(MoO4)2(OH)2\mathrm{Cu}_3(\mathrm{MoO}_4)_2(\mathrm{OH})_2 and Cu3Mo2O9\mathrm{Cu}_3\mathrm{Mo}_2\mathrm{O}_9 nanosheets.

Fig. 8. Room-temperature photoluminescence spectrum of the prepared Cu3(MoO4)2(OH)2\mathrm{Cu}_3(\mathrm{MoO}_4)_2(\mathrm{OH})_2 nanosheet sample.

Fig. 9. Magnetic properties of the lindgrenite nanosheets: magnetization vs. field and hysteresis loops of sample at room temperature.

Fig. 10. Room-temperature photoluminescence spectrum of the Cu3Mo2O9\mathrm{Cu}_3\mathrm{Mo}_2\mathrm{O}_9 nanosheets (calcined at 500 ∘C500\,^\circ\mathrm{C}).

Fig. 11. Magnetic properties of the Cu3Mo2O9\mathrm{Cu}_3\mathrm{Mo}_2\mathrm{O}_9 nanosheets: magnetization vs. field and hysteresis loops of sample at room temperature.

X-ray diffraction patterns

Figure 1 (PDF p. 20). Fig. 1

Infrared transmittance spectra of samples a, b, and c

Figure 2 (PDF p. 21).

Scanning electron micrograph of rod-shaped particles

(a)

Scanning electron micrograph of aggregated particles

(b)

Scanning electron micrograph of plate-like particles

(c)

Scanning electron micrograph of clustered particles

(d)

Scanning electron micrograph of elongated particles

(e)

Scanning electron micrograph of spherical particles

(f)

Figure 12 (PDF p. 22).

Figure 3 (PDF p. 23).

X-ray diffraction patterns labeled a, b, and c

Figure 4 (PDF p. 24).

Three stacked FTIR spectra labelled a, b, and c, showing transmittance against wavenumber

Figure 5 (PDF p. 25).

Scanning electron micrograph, panel a

(a)

Scanning electron micrograph, panel b

(b)

Scanning electron micrograph, panel c

(c)

Scanning electron micrograph, panel d

(d)

Scanning electron micrograph, panel e

(e)

Figure 6 (PDF p. 26).

TG and DTA curves as a function of temperature

Figure 7 (PDF p. 27).

Intensity as a function of wavelength

Figure 8 (PDF p. 27).

Magnetization versus applied field

Figure 9 (PDF p. 28).

Intensity versus wavelength

Figure 10 (PDF p. 28).

Magnetization versus applied field

Figure 11 (PDF p. 29).

References

  1. [1]L. Zhang, T. Li, Y. Deng and et al. J Iran Chem Soc. 11 (2014) 407–414
  2. [2]W. G. Chu, H. F. Wang, Y. J. Guo and et al. Inorg. Chem. 48 (2009) 1243
  3. [3]P. C. Lindgrenite, Am. Mineral. 20 (1935) 484
  4. [4]B. R. lie, K. Z. ping, G. Min and et al. Chem. Res. Chinese U. 22 (2006) 679
  5. [5]J. W. Jun, F. Jin, F. Z. Yong, Y. X. Jie, L. Q. Ting, H. Y. Bin, Inorg. Mater. 26 (2011) 438-442
  6. [6]M. Alexandre, G. Beyer, C. Henrist and et al. Macromol. Rapid Commun, 22 (2001) 643
  7. [7]H. Li, Y. Chen and Y. Xie, Mater. Lett. 57 (2003) 2848
  8. [8]J. Xu and D. Xue, J. Solid State Chem. 180 (2007) 119
  9. [9]S. Vilminot, G. Andre, M. R. Plouet, F. B. Vigneron, M. Kurmoo, Inorg. Chem. 45 (2006) 10938-10946
  10. [10]J. Xia, L. X. Song, W. Liu and et al. Dalton Trans. 44 (2015) 13450
  11. [11]F. K. Butt, C. Cao, R. Ahmed and et al. CrystEngComm. 16 (2014) 894
  12. [12]Y. Zhang, H. Chenguo, B. Feng, X. Wang and B. Wan, Appl. Surf. Sci. 257 (2011)10679
  13. [13]S. Ohira, T. Sugawara, K. Nakajima and T. Shishido, J. Alloys Compd. 402 (2005) 204
  14. [14]Y. Sun, H. Cheng, S. Gao, Z. Sun, Q. Liu, Q. Liu, F. Lei, T. Yao, J. He, S. Wei and Y. Xie, Angew. Chem., Int. Ed. 51 (2012) 8727
  15. [15]M. Safdar, Z. Wang, M. Mirza, F. K. Butt, Y. Wang, L. Sun and J. He, J. Mater. Chem. A 1 (2013) 1427
  16. [16]F. C. Hawthorne, R. K. Eby, Neues Jb. Miner. Monats. 5 (1985) 243
  17. [17]L. D. Calvert and W. H. Barnes, Can. Mineral. 6 (1957) 31
  18. [18]W. Jiang, X. Hua, Q. Han and et al. Powder Technol. 191(2009) 227
  19. [19]S. A. Hassanzadeh-Tabrizi, E. Taheri-Nassaj and H. Sarpolak y, J. Alloys Compd. 456 (2008) 282
  20. [20]T. D. Nguyen and T. O. Do, Langmuir 25 (2009) 5322
  21. [21]D. Zhao, Q. Yang, Z. Han, F. Sun, K. Tang and F. Yu, Solid State Sci. 10 (2008) 1028
  22. [22]J. Yang and J. Y. Ying, Nat. Mater. 8 (2009) 683
  23. [23]P. Gibot and L. Laffont, J. Solid State Chem. 180 (2007) 695
  24. [24]T. D. Nguyen, D. Mrabet and T. D. Do, Phys. Chem. C 112 (2008) 15226
  25. [25]P. Huang, X. Zhang, J. Wei, J. Pan, Y. Sheng, B. Feng, Mater. Chem. Phys. 147 (2014) 996-1002
  26. [26]J. W. Jun, F. Jin, F. Z. Yong, Y. X. Jie, L. Q. Ting, H. Y. Bin, Inorg. Mater. 26 (2011) 438-442
  27. [27]Z. Luo, et al. Cryst. Growth Des. 8 (2008) 2275
  28. [28]T. D. Nguyen, C. T. Dinh, T. O. Do, Nanoscale, 3 (2011) 1861-1873
  29. [29]J. Tang and A.P. Alivisatos, Nano Lett. 6 (2006) 2701
  30. [30]J. Xu, D. Xue, J. Phys. Chem. B 110 (2006) 17400
  31. [31]J. Xu, D. Xue, J. Phys. Chem. B 110 (2006) 11232
  32. [32]U. Steiner, W. Reichelt, Acta Crystallogr. C 53 (1997) 1371.
  33. [33]R. Shi, Y. Wang, F. Zhou, Y. Zhu, J. Mater. Chem. 21 (2011) 6313–6320
  34. [34]T.D. Nguyen, et al., CrystEngComm 13 (2011) 1450–1460
  35. [35]C. J. Mao, J. Geng, X. C. Wu and J. J. Zhu, J. Phys. Chem. C 114 (2010) 1982
  36. [36]Q. Gong, X. F. Qian, X. D. Ma and Z. K. Zhu, Cryst. Growth Des. 6 (2006) 1821
  37. [37]D. Chen, K. B. Tang, F. Q. Li and H. G. Zheng, Cryst. Growth Des. 6 (2006) 247
  38. [38]J. A. Groenink, C. Hakfoort and G. Blasse, Phys. Status Solidi A 54 (1979) 329
  39. [39]R. Dinesh, T. Fujiwara, T. Watanabe, K. Byrappa and M. Yoshimura, J. Mater. Sci. 41 (2005) 1541
  40. [40]G. Ahmad, M. B. Dickerson, B. C. Church, Y. Cai, S. E. Jones, R. R. Naik, J. S. King, C. J. Summers, N. Kroger and K. H. Sandhage, Adv. Mater. 18 (2006) 1759
  41. [41]J. C. Szczancoski, L. S. Cavalcante, M. R. Joya, J. A. Varela, P. S. Pizani and E. Longo, Chem. Eng. J. 140 (2008) 632
  42. [42]W. S. Wang, L. Zhen, C. Y. Xu and W. Z. Shao, Cryst. Growth Des. 9 (2009) 1558

Paper details

vlnc:W_jc5tfcmk
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 4

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents