betaFeedback

WorksPhysics and Astronomy

Comparative Analysis of the Electronic Energy Structure of Nanocrystalline Polymorphs of Y2O3 Thin Layers: Theory and Experiments

Abstract

The results of fabrication and characterization of atomic structure of nanocrystalline thin layers of Y2O3 in cubic and monoclinic phases is reported. Experimental data demonstrate crystalline ordering in nanocrystalline films with average grain size of ~10-14 nm both for cubic and monoclinic studied structures. Density Functional Theory (DFT) based simulations demonstrate insignificant differences of electronic structure of these phases in the bulk and on the surfaces. Theoretical modeling also pointed out the significant broadening of valence and conductive bands caused by means of energy levels splitting in agreement with experimental data (X-ray photoelectron and photoluminescence spectra). The presence of various intrinsic and extrinsic defects (including surface adsorption of carbon mono- and dioxide) does not promote visible changes in electronic structure of Y2O3 surface for both studied phases. Optical absorption and luminescence measurements indicate insignificant bandgap reduction of Y2O3 nanocrystalline layers and the very little contribution from defect states. Simulation of extrinsic compression and expanding demonstrate stability of the electronic structure of nanocrystalline Y2O3 even under significant strain. Results of comprehensive studies demonstrate that yttrium oxide based nanocrystalline layers are prospective for various optical applications as a stable material.

Introduction

Yttrium oxide thin-films have wide application importance since they usually exhibit good chemical and thermal stability with high melting point, fracture toughness, high refractive index, relatively wide band-gap (see, i.e., Refs. [1, 2, 3, 4], etc. These features allow to employ Y2O3\mathrm{Y}_{2}\mathrm{O}_{3} films as technologically suitable coatings for thermo-protective barriers, electric gate interfaces and others for different commercial applications [5, 6]. In addition, Y2O3\mathrm{Y}_{2}\mathrm{O}_{3} is used as a host material for doping with different ions, especially with rare-earth and transition ions [7, 8]. Optical properties of Y2O3\mathrm{Y}_2\mathrm{O}_3-based materials usually well meet manufacturing requirements for creation of light-emitting diodes [9], color displays [10], lasers [11], solar cells [12], bio-imaging systems [13], etc.

It is known that yttrium oxide can exist in three polymorphic forms denoted as A-type (hexagonal), B-type (monoclinic) and C-type (cubic) structures [14]. Most of published papers deal with the study of cubic Y2O3\mathrm{Y}_2\mathrm{O}_3 properties, because it is stable at room temperature and standard atmospheric pressure. Also relatively simple synthesis conditions are required in order to yield cubic polymorph what is one more technological advantage. Monoclinic and hexagonal yttrium oxides have been studied to a much lesser extent if compared with cubic polymorph. This circumstance is usually associated with technological difficulties of A- and B-type Y2O3\mathrm{Y}_2\mathrm{O}_3 synthesis: here the need to apply elevated temperatures (up to 2600 K) and high pressures (up to 32 GPa) [15, 16] exists. However, even these extreme synthesis conditions cannot guarantee the yield of single-phase final material. Due to technological difficulties of a single-phase monoclinic Y2O3\mathrm{Y}_2\mathrm{O}_3 synthesis, the properties of this polymorph had been poorly studied if compared with that for cubic Y2O3\mathrm{Y}_2\mathrm{O}_3. Additional pitfall for growing Y2O3\mathrm{Y}_2\mathrm{O}_3 thin-films on a substrate is fairly strong dependence of growing film on size effects in the vertical axis, which increases the difficulty in optimization of mechanical properties [17]. For this reason, strict grade control of final product with surface sensitive research methods is needed.

The features of electronic and optical properties of any material essentially depend on atomic and energy structure arrangements: crystal symmetry type, defectiveness, electronic and phonon density of states. For example, it was shown in Ref. [18] that monoclinic Y2O3\mathrm{Y}_2\mathrm{O}_3 films are characterized by slightly larger band gap and slightly lower refractive index if compared with that for cubic Y2O3\mathrm{Y}_2\mathrm{O}_3 films. The influence of point defects in the structure of cubic Y2O3\mathrm{Y}_2\mathrm{O}_3 on luminescent characteristics has been studied in Refs. [19, 20]. It was found that both oxygen vacancies and interstitial oxygen in the cubic Y2O3\mathrm{Y}_2\mathrm{O}_3-host usually lead to a decrease in luminescence quantum yield of europium [19] and bismuth [20] doping ions. At the same time, we have to note that there is no data concerning the influence of defectiveness on optical properties of monoclinic Y2O3\mathrm{Y}_2\mathrm{O}_3 polymorph, what can be considered as a separate challenging scientific task. In the case of monoclinic yttrium oxide, this issue is of particular importance, since the fabrication of stable monoclinic phase is possible only when non-stoichiometry of oxygen sublattice exists, as was shown in Ref. [21].

In the current paper we consider issues related to the comparative study of energy structure of cubic and monoclinic Y2O3\mathrm{Y}_2\mathrm{O}_3 films, as well as the influence of various types of defects on the formation of optical properties of these Y2O3\mathrm{Y}_2\mathrm{O}_3 polymorphs. We will apply experimental methods of X-ray Photoelectron Spectroscopy and Optical Spectroscopy in combination with DFT-based simulations for data analysis. These analyzed data will provide necessary groundwork for onward studies of thin-film materials based on yttrium oxide with different crystal structures.

Samples and Experimental Details

Y2O3\mathrm{Y}_2\mathrm{O}_3 films were deposited on silica glass substrates using dc-pulsed mode (50 kHz, 10 μ\mus) of reactive magnetron sputtering technology. Prior deposition, silica glass substrates were cleaned in ultrasonic bath employing acetone solution for 20 min onward drying in airflow. In order to obtain a film with cubic structure, a target with a diameter of 40 mm and a thickness of 2 mm was prepared by cold pressing of yttrium metal powder at 30 MPa. As for monoclinic film, sodium was added during preparation of the target. The purpose of adding sodium is to stabilize monoclinic Y2O3\mathrm{Y}_2\mathrm{O}_3 phase. Usually, an addition of alkali ions into rare-earth oxide is employed to create non-stoichiometry in oxygen sublattice [22]. As it was reasonably shown in Ref. [21], oxygen vacancies promote the nucleation of monoclinic Y2O3\mathrm{Y}_2\mathrm{O}_3 phase. Sodium with an expected ∼\sim5 at. % concentration was introduced into the coating at the stage of its deposition. To obtain sodium vapor, a soda-lime glass plate was heated to temperatures close to the glass transition temperature. Plasma sodium vapor content was monitored by the amplitude of the sodium doublet line λ\lambda=589.0 nm in the plasma emission spectrum.

The magnetron, sputtered target, and the substrate were placed in a vacuum chamber pumped down to 6.6×10−36.6 \times10^{-3} Pa with the help of turbomolecular pump. Sputtering was carried out for 8 hours at magnetron power of 30 W in argon-oxygen atmosphere with 0.4 Pa total pressure (the volume concentration of oxygen was less than 30 %). The temperature of substrate was 400 ±\pm 25°C during deposition procedure. After deposition has been completed, the sample was cooled down to room temperature in vacuum chamber at 10−510^{-5} Torr pressure. The thicknesses of Y2O3\mathrm{Y}_2\mathrm{O}_3 films were determined to be ∼\sim800 nm employing ball-abrasion method with the help of Calotest device (CSM Instruments SA, Switzerland).

Structural-phase analysis of the samples under study was performed by means of X-ray diffraction using XPertPro MPD diffractometer with Cu Kα\alpha = 1.5405 Å radiation. Diffraction patterns obtained (see Figure 1) confirm the formation of single-phase cubic Y2O3\mathrm{Y}_2\mathrm{O}_3 film (lattice parameter a=10.73a = 10.73 Å [23] and single-phase monoclinic Y2_2O3_3 film (lattice parameters: a=14.07a = 14.07 Å, b=3.32b = 3.32 Å and c=8.68c = 8.68 Å) [24]. The processing of diffraction pattern was performed using TOPAS 3 full-profile analysis program accounting the presence of predominant orientation of crystallites (texture) in the material under study. Being parallel to surface the planes (111) and (201) were found as preferred orientation for cubic and monoclinic Y2_2O3_3, respectively.

X-ray diffraction patterns of cubic and monoclinic Y2O3 films

Figure 1. X-ray diffraction patterns of cubic (a) and monoclinic (b) Y2_2O3_3 films. Reflexes were identified in accordance with JSPDS No. 43-1036 (for cubic Y2_2O3_3 phase) and JSPDS No. 44-0399 (for monoclinic Y2_2O3_3 phase) Standard Cards. A wide diffuse peak originates from silica glass substrate.

FilmCrystal structureLattice ParametersAverage size of coherent scattering
Y2_2O3_3cubic, Ia3a=10.73a = 10.73 Å10±210 \pm2 nm
Na:Y2_2O3_3monoclinic, C/2ma=14.07a = 14.07 Å, b=3.32b = 3.32 Å, c=8.68c = 8.68 Å13±213 \pm2 nm

Table I. Structural-phase characteristics of studied Y2_2O3_3 films.

The average sizes of coherent scattering DD were determined to be 10 nm and 13 nm for cubic and monoclinic films, correspondingly. Assuming that nanocrystallites have a spherical shape, we can estimate surface-to-volume ratio as 0.30±0.050.30 \pm0.05 nm−1^{-1} and 0.23±0.050.23 \pm0.05 nm−1^{-1} for nanocrystallites of cubic and monoclinic Y2_2O3_3 films, respectively. Table I summarizes structural-phase characteristics of the samples under study.

Since yttrium oxide films are widely used in different optical applications (see Introduction section), it is logically to apply surface-sensitive methods in order to inspect chemical composition and grade of the surface of our samples. For this reason, we employed X-ray Photoelectron Spectroscopy (XPS) using survey and core-level analysis with the help of ThermoScientific KK-alpha Plus XPS spectrometer. This spectrometer has monochromatic microfocused Al KαK\alpha X-ray source and has 0.05 at. % element sensitivity [25]. An operating pressure in analytic chamber during measurements was not worse than 1.1×10−61.1 \times10^{-6} Pa. Dual-channel automatic charge compensator (GB Patent 2411763) was applied to exclude the charging of our sample under XPS analysis because of the loss of photoelectrons. Pre-run up procedures performed included standard degassing of the sample and analyzer binding energy scale inspection and re-calibration (if needed) employing sputter cleaned Au (4f7/24f_{7/2} band), Ag (3d5/23d_{5/2} band), and Cu (2p3/22p_{3/2} band) inbuilt XPS Reference Standards according to ISO 16.243 XPS International Standard and XPS ASTM E2108-00 Standard. We used ThermoScientific XPS spectrometer inbuilt electronic database, NIST XPS Standard Reference Database [26] and Handbook of Monochromatic XPS Spectra: The Elements of Native Oxides [27] to identify precisely survey spectrum structure (see Figure 2).

Image not extracted

Figure 2. X-ray photoelectron survey spectra of monoclinic and cubic Y2O3Y_2O_3 films.

It is well seen from Figure 1 that most intensive peaks belong to yttrium and oxygen which are the components of yttrium oxide. At the same time Na (5.51 at.%) is present monoclinic yttrium oxide film what is the feature of the synthesis technology employed as it has been reported above. As for carbon contamination, it is present in both samples due to well-known ability of Y2O3Y_2O_3 to absorb CO and CO2CO_2 species from atmosphere (see, i.e., Ref. [28] and general comments of ThermoScientific on yttrium oxide XPS study [29]). The concentrations of carbon according to our measurements are different for monoclinic and cubic polymorphs: they are 5.56 and 3.97 at.%, respectively. The measured O/Y ratio gives the values 1.46 and 1.50 for monoclinic and cubic Y2O3Y_2O_3, respectively. These values are in a good agreement with data for monoclinic and cubic Y2O3Y_2O_3 reported in Refs. [30, 31]. We have to note that freshly synthesized samples are inspected now and all these values obtained well coincide with our previous findings reported earlier in Refs. [23, 24]. This means good technological reproducibility of monoclinic and cubic Y2O3Y_2O_3 films with the help of synthesis employed.

XPS Survey of Y₂O₃ in monoclinic and cubic phases

Figure 3.

Theoretical modeling of pristine, defective and oxidized Y2O3\mathrm{Y}_2\mathrm{O}_3 was performed with the use of QUANTUM-ESPRESSO pseudopotential code [32] employing the generalized gradient approximation [33] for exchange-correlation potential in a spin-polarized mode. A full optimization of atomic positions was carried out. During optimization, the electronic ground state was consistently found using ultra-soft pseudopotentials [34]. In order to simulate adsorption of CO and CO2\mathrm{CO}_2 species by yttrium oxide, an additional correction for London dispersion forces (+vdW) were used. [35] The forces and total energies were optimized with accuracies of 0.04 eV Å−1^{-1} and 1.0 meV/supercell, respectively. For the modeling of bulk, we used 3×3×33 \times3 \times3 supercell of cubic or monoclinic Y2O3\mathrm{Y}_2\mathrm{O}_3 phase (see Fig. 3). For the modeling of surface we used the slabs constructed from the same supercell.

Calculations of formation energies of defects and adsorption were performed using standard formula:

Eform=E(products)−[E(host)±E(impurities)]m,(1)E_{\mathrm{form}} = \frac{E(\mathrm{products}) - [E(\mathrm{host}) \pm E(\mathrm{impurities})]}{m}, \tag*{(1)}

where E(products)E(\mathrm{products}) is the total energy with defects or adsorbed molecules; E(host)E(\mathrm{host}) is total energy of the system before formation of defects or adsorption of molecules, and E(impurities)E(\mathrm{impurities}) denotes total energies of adsorbed mm molecules or formation of mm defects in lattice. In the case of interstitial impurities incorporation the sign of total energies of defects in mentioned above formula is plus and in the case of vacancies formation the sign is minus. In the case of multiple defects E(impurities)E(\mathrm{impurities}) is the superposition of energies of removed and/or inserted defect atoms. For adsorption of carbon monoxide E(impurity)E(\mathrm{impurity}) denotes total energy of single molecule in gaseous phase. The energy value employed for calculations of oxygen defects is total energy of oxygen molecule in gaseous phase divided by two. The energy of sodium impurity was calculated by the following formula:

E(Na)=(E(Na2O)−E(O2)/2),(2)E(\mathrm{Na}) = (E(\mathrm{Na}_{2}\mathrm{O}) - E(\mathrm{O}_{2})/2), \tag*{(2)}

where E(Na2O)E(\mathrm{Na}_{2}\mathrm{O}) denotes total energy of bulk Na2O\mathrm{Na}_{2}\mathrm{O}. Note that negative values of formation energies correspond to exothermic processes whereas positive values correspond to endothermic processes.

Top view of optimized atomic structure of cubic (a) and different views optimized atomic structures monoclinic (b-d) Y2O3 polymorphs

Figure 3 (PDF p. 7). Top view of optimized atomic structure of cubic (a) and different views optimized atomic structures monoclinic (b-d) Y2O3\mathrm{Y}_{2}\mathrm{O}_{3} polymorphs. Yttrium atoms are denoted by means of large grey-blue spheres whereas oxygens are shown as small red spheres.

Results and Discussion

XPS spectral analysis

X-ray Photoelectron (XPS) Y 3d core-level spectra of monoclinic and cubic Y2_2O3_3 films are shown in Figure 4. These spectra have well-resolved spin-orbit 5/2 and 3/2 which are located at 156.27 and 158.25 eV, respectively. Appropriate Y 3d core-level of pure Y-metal of XPS External Standard after ThermoScientific are located at more visible lower binding energies (BE = 155.98 eV and 157.99 eV) what is allowing to state that no separate Y-metal phase is present in our samples under study, i.e. samples were synthesized without even partial segregation of Y-metal. This conclusion well coincide with XRD data reported earlier that also indicate single-phase yield of monoclinic and cubic polymorphs of Y2_2O3_3 films due to the synthesis technology employed [23, 24]. At the same time well seen that XPS could not detect the differences in Y 3d core-levels between monoclinic and cubic films of Y2_2O3_3 films which is somewhat unusual at first glance. Actually cubic and monoclinic polymorphs of yttrium oxide have quite different lattice parameters (a=b=c=10.73a = b = c = 10.73 Å [23] and a=14.07a = 14.07 Å, b=3.32b = 3.32 Å and c=8.68c = 8.68 Å [24]) and crystal structures, respectively, but valence state of yttrium is the same in these polymorphs and large number of Y–O bonds have almost the same values (approximately 2.2 Å according to calculated atomic structures, see Figure 2 and details of calculation procedure) so this might be the reason for above mentioned situation. Generally speaking, the same story occurs with XPS of rutile and anatase polymorphs of TiO2\mathrm{TiO}_2 where as well not possible to distinguish Ti 2p core-levels among each other (see, e.g., Fig.3a in Ref. [36]) despite visible significant differences in atomic structure but again very similar values of interatomic distances and angles. Additionally, surface and subsurface layers of both Y2O3\mathrm{Y}_2\mathrm{O}_3 polymorphs could be modified by absorbed CO and CO2\mathrm{CO}_2 species [28, 29] so the dissimilarities between them are leveled by surface defects and newly formed bonds C–O–Y what is impeding XPS analysis of spectra differences. We will inspect all mentioned above statements using O 1s and C 1s core-level spectra analysis and, of course, the onward theoretical modeling with the help of DFT-calculations of electronic densities of states and atomic structure simulations of bulk and surface.

X-ray Photoelectron Y 3d core-level spectra of monoclinic and cubic Y2O3 films

Figure 4. X-ray Photoelectron Y 3d core-level spectra of monoclinic and cubic Y2_2O3_3 films. Also XPS Y-metal XPS External Standard Y3d spectrum is shown for comparance.

XPS O 1s and C 1s core-level spectra are shown in Figure 5 a-Figure 5b. XPS O 1s spectra exhibit double-band structure with the main band located at 529.86 eV and sub-band located at 532.12 eV (see Figure 5a). These BE-values well coincide with data reported by P. Yu et. al. [21] and NIST XPS Standard Reference Database [26]. Weak and broad Na Auger band is present in O 1s core-level spectrum due to embedded sodium in this sample, because sodium was used in order to promote the nucleation of monoclinic Y2O3\mathrm{Y}_2\mathrm{O}_3 phase (see Ref. [21, 24] and sample preparation details in the current paper). The most remarkable fact is that 532 eV sub-band has dissimilar intensities in O 1sO\ 1s core-level spectra of monoclinic and cubic polymorphs of Y2O3Y_2O_3 films. Since this sub-band is linked with oxygen-carbon imperfections of oxygen sublattice [21] due to absorbed CO and CO2_2 species, an appropriate “oxygen-carbon” sub-band should be present in C 1sC\ 1s core-level spectra of monoclinic and cubic polymorphs of Y2O3Y_2O_3 films. Exactly this sub-band one can easily see at 288.68 eV in Figure 4b which is linked with O−C=OO-C=O bonds [26, 37]. Additionally, exactly monoclinic polymorph O 1sO\ 1s and C 1sC\ 1s spectra have higher intensity of O−CO-C and O−C=OO-C=O bands, respectively, because of different O/YO/Y relation for monoclinic and cubic Y2O3Y_2O_3 and differently absorbed carbon (see Samples and Experimental Details section and Refs. 22-23). This means a good agreement among our core-level spectra and data of outside researchers cited above.

X-ray photoelectron core-level O 1s and C 1s spectra of monoclinic and cubic polymorphs of Y2O3 films

Figure 5. X-ray photoelectron core-level O 1s (a) and C 1s (b) spectra of monoclinic and cubic polymorphs of Y2O3\mathrm{Y}_2\mathrm{O}_3 films.

At the final stage of our XPS analysis we performed Valence Band (VB) mapping of electronic states for monoclinic and cubic polymorphs of Y2O3Y_2O_3 films (Figure 6). This mapping was made using crossed-referencing among NIST XPS Standard Reference Database [26], Handbook of Monochromatic XPS Spectra [27], ThermoScientific XPS Knowledge Base [37], ThermoScientific XPS spectrometer inbuilt electronic database and Atomic Calculation of Photoionization Cross-Sections and Asymmetry Parameters for Al Kα\alpha X-ray probe (recall, we have used Al Kα\alpha X-ray Microfocused source for excitation of our x-ray photoelectron spectra) [38]. The most important now, to establish the majority of electronic states in strongly overlapped areas of Valence Bands. Overlapped Y 4p + O 2s states area of binding energies is characterized by the majority contribution of Y 4p electronic states because of the following photoionization cross-sections relation: σ\sigma(Y 4p) : σ\sigma(O 2s) = 1.2 : 0.19 [38]. The O 2s + C 2s area in the range from 21.5 eV up to 16 eV exhibit σ\sigma(O 2s) : σ\sigma(C 2s) = 0.19 : 0.066 cross-sections relation. This means that the contribution of carbon C 2s into VB of studied Y2_2O3_3 films is very weak in this BE-region and sub-band located at 19.4 eV (see Figure 6) is predominantly of O 2s character [38]. The most interesting is mapping of Valence Baseband region. Here relation is σ\sigma(Y 4d) : σ\sigma(O 2p) : σ\sigma(Na 3s) = 4.5 : 2.4 : 0.0097 [38] so formally Valence Baseband is related with Y 4d majority. Finally, valence bands were identified as the bands with Y 4p and Y 4d majority contributions. We suppose that weak differences in VB’s are exactly due for this reason, because yttrium is in the same valence state in both polymorphs of studied Y2_2O3_3 films. Of course, all these interpretations of VB mapping will be inspected by means of electronic densities of states calculations in theoretical part of current paper.

XPS Valence Band spectra of monoclinic and cubic polymorphs of Y2O3 films

Figure 6. X-ray photoelectron Valence Band (VB) spectra of monoclinic and cubic polymorphs of Y2O3Y_2O_3 films.

Theoretical modeling

An inspection of suitability of used approach for the modeling of yttrium oxide was selected as the first step of our simulations. For this purpose we performed calculations of bulk Y2_2O3_3 which has cubic and monoclinic structures. The deviations between calculated and experimentally measured values of lattice vectors are below 1%. Calculated total energy per formula unit of monoclinic phase is 70.1 meV and this value is higher than that for cubic one. Thus calculations performed also suggest smaller stability of monoclinic yttrium oxide.

Next step of our modeling is the calculation of formation energies of various impurities in the bulk morphology of both phases of Y2_2O3_3 – cubic and monoclinic. We also considered formation of oxygen defects in interstitial void positions (Oi_i, see Figure 7) additionally to conventional defects in oxides such as oxygen vacancies (vO_\mathrm{O}). Since stabilization of monoclinic phase requires some Na-doping so the formation of substitution (NaY_\mathrm{Y}) and interstitial (Nai_i) defects was also simulated. For the sake of comprehensiveness all possible combinations of sodium and oxygen defects were simulated in both phases. Results of the calculations performed (see Table II) demonstrate that formation of defects in cubic phase of Y2_2O3_3 is extremely unfavorable and requires energies above 5.7 eV per defect. Thus we can conditionally consider cubic phase as stable and almost defect-free. Contrary, the formation of defects in less stable monoclinic Y2O3\mathrm{Y}_2\mathrm{O}_3 requires smaller values of energy. For some kind of defects (such as interstitial oxygen and pair of interstitial oxygen and sodium defects, see Figure 7) formation energies are relatively moderate: they are 1.08 and 2.04 eV/defect, respectively. Therefore, an appearance of defects mentioned in monoclinic Y2O3\mathrm{Y}_2\mathrm{O}_3 is very likely.

Optimized atomic structure of supercell employed for the modeling of bulk and (010) surface of monoclinic Y2O3 with interstitial sodium and oxygen defects

Figure 7. Optimized atomic structure of supercell employed for the modeling of bulk (a) and (010) surface (b) of monoclinic Y2O3\mathrm{Y}_2\mathrm{O}_3 with interstitial sodium (large yellow spheres) and oxygen (shown as circles) defects. Yttrium atoms are shown by large grey-blue spheres; oxygen atoms are small red spheres.

ConfigurationPhaseEformE_{\mathrm{form}} in bulk (eV/atom)Surface (eV/Y2O3Y_2O_3)Surface+vOv_{\mathrm O} (eV/O)
defect freecubic<br>monoclinic.<br>.3.31<br>0.41-8.63<br>5.74
vOv_{\mathrm O}cubic<br>monoclinic6.68<br>6.67.<br>0.39.<br>6.05
iOi_{\mathrm O}cubic<br>monoclinic9.05<br>1.08.<br>0.41.<br>-1.03
NaYcubic<br>monoclinic11.16<br>10.67.<br>0.37.<br>2.02
NaY+vOv_{\mathrm O}cubic<br>monoclinic5.77<br>5.58.<br>0.55.<br>6.11
NaY+iOi_{\mathrm O}cubic<br>monoclinic9.67<br>5.40.<br>1.89.<br>-0.63
Naiicubic<br>monoclinic12.89<br>4.70.<br>0.59.<br>5.35
Naii+vOv_{\mathrm O}cubic<br>monoclinic9.47<br>5.58.<br>0.56.<br>5.67
Naii+iOi_{\mathrm O}cubic<br>monoclinic5.74<br>2.04.<br>0.55.<br>2.08

Table II. Formation energies of various defects in the bulk Y2O3Y_2O_3 for cubic and monoclinic phases. Also surface formation energies and oxygen vacancies (vOv_{\mathrm O}) in the surfaces of discussed systems are given. The most probable configurations of defects are shown in bold.

Correct theoretical description of electronic structure and physical properties of thin layers requires simulation of both bulk and surface for studied materials. For this purpose we constructed the slab from supercells used for the simulation of defects in the bulk phase. Since all crystallographic surfaces are the same in cubic Y2O3Y_2O_3, so for this reason we simulated (001) surface. In the case of monoclinic phase only the formation of (010) surface corresponds the absence of dangling bonds. The formation of defects in cubic Y2O3Y_2O_3 is very unfavorable for this phase, thus we considered only the surface of defect-free slabs. For monoclinic phase, we performed simulations of the surfaces with all considered kinds of defects in bulk (see Figure 7b for example). Also we performed simulations of oxygen vacancies formation in the surface layer. In order to evaluate such surface, we calculated the changes of total energies per formula unit of the systems as the bulk and the slab. On the one hand, the results of calculations performed (see Table II) demonstrate that formation of surface in cubic phase has relatively large energy cost, it is approximately 3.3 eV/Y2O3Y_2O_3). From the other hand the formation of oxygen vacancy in surface layer is negative. Therefore, we can propose the formation of multiple oxygen defects in the surface of cubic Y2O3\mathrm{Y_2O_3}. Contrary, formation of (010) surface of monoclinic phase usually meets with rather moderate energy costs (within 0.5 eV/Y2O3\mathrm{Y_2O_3}) for almost all considered types of crystal structure. Formation energies of oxygen defects in these surfaces correspond to endothermic process for all cases except the presence of interstitial oxygen impurity. In the latter case the formation of oxygen defects can be discussed as removal of excessive oxygen from the lattice.

The last step of our study of the various impurities in Y2O3\mathrm{Y_2O_3} is simulation of adsorption process of carbon mono and dioxide onto the surface of cubic and monoclinic phases (see Figure 8). Calculated adsorption energies for CO are 0.33 and 0.59 eV/CO for cubic and monoclinic phases, respectively. As for CO2\mathrm{CO_2}, these values are 0.12 and 0.46 eV/CO2\mathrm{CO_2} for cubic and monoclinic phases. Note, that decomposition of CO and CO2\mathrm{CO_2} were not observed in the simulations performed (see Figure 8). Hence experimentally observed contribution from carbon and CO bonds (see Figure 5) can be attributed to robust physical adsorption of CO and CO2\mathrm{CO_2} on the surfaces and grain boundaries of inspected Y2O3\mathrm{Y_2O_3} layers.

Optimized atomic structures and changes of charge densities for physical adsorption of CO on cubic and monoclinic Y2O3 surfaces

Figure 8. Optimized atomic structure and changes of charge densities for physical adsorption of CO on (001) surface of cubic (a) and (010) surface of monoclinic (b) lattices of Y2O3\mathrm{Y_2O_3}.

Yttrium atoms are shown employing large grey-blue spheres, whereas oxygen and carbon atoms are small red and brown spheres, respectively. Blue and yellow colors of charge density “clouds” correspond to the decreasing and increasing of charge density after adsorption.

The last part of our theoretical studies of two phases of Y2_2O3_3 is the inspection of influence of surface and defects formation on the bulk surface of considered model systems. Results of the calculations performed demonstrate that electronic structure of bulk cubic and monoclinic Y2_2O3_3 is indistinguishable (see black lines on Figure 9 a,b). Formation of the surface also affects similarly of both structures. The valence bands became broader with multiple peaks there and narrow in the bulk phase. At the same time Y 4p and O 2s bands also split and became broader (see Figure 9 a,c). Note, that positions and widths of these peaks is the same for both considered phases. Two reasons of such changes in electronic structure can be proposed. The first one is appearance of surface and subsurface layers with electronic structure having differences from that for the bulk. The second is a violation of the symmetry in vicinity of surface (see Fig. 3 and Figure 7a in comparance with Figure 7b and Figure 8). Extremely narrow peaks in electronic structure of bulk Y2O3\mathrm{Y}_{2}\mathrm{O}_{3} is an evidence of bands degeneration even in the presence of defects (see Figure 9b). Thus we can propose the violation of symmetry in subsurface area as the leading reason of splitting energy levels of Y2O3\mathrm{Y}_{2}\mathrm{O}_{3} valence bands for both considered types of lattice.

Total densities of states for cubic and monoclinic Y$_2$O$_3$ bulk and surface structures

Figure 9. Total Densities of States (DOS) for the bulk morphologies (a,b) and surface (a,c,d) of Y2_2O3_3 with cubic (a) and monoclinic (b-d) lattices with and without various defects and surface impurities (see legends).

At the final step of our simulations we performed an inspection of the influence of adsorbed species and impurities on the electronic structure of yttrium oxide-based layers. Robust adsorption of carbon monoxide on the surface of Y2O3\mathrm{Y}_{2}\mathrm{O}_{3} provides appearance of similar small peaks in electronic structure for both considered phases (see magenta lines on Figure 9a,Figure 9c). These peaks can be clearly attributed with 2s and 2p states of carbon and oxygen of CO molecule (see Figure 10a). Despite of relatively large magnitude of adsorption energies the influence of CO on valence band is miniscule. Redistribution of charge density after CO adsorption on the surfaces of Y2O3\mathrm{Y}_{2}\mathrm{O}_{3} (see Figure 8) demonstrates significant changes in charge density of molecule which correspond to the appearance of some electronic states between -2 and -5 eV in electronic structure of CO (see Figure 10a). Contrary changes of the charge densities in substrates are very local (Figure 8). Thus we can conclude that adsorption of carbon mono and dioxides onto the surface and grain boundaries do not influence electronic structure of Y2O3Y_2O_3 in both phases.

Partial densities of states for carbon monoxide and interstitial sodium and oxygen impurities

Figure 10. Partial densities of states for (a) carbon monoxide molecule adsorbed on (010) surface of monoclinic Y2O3\mathrm{Y}_{2}\mathrm{O}_{3} (see Figure 8b) and interstitial sodium and oxygen impurities in bulk monoclinic Y2O3\mathrm{Y}_{2}\mathrm{O}_{3} (see Figure 7a).

In the case of interstitial oxygen and sodium impurities in the bulk phase we also observe appearance of some minor peaks in electronic structure (see Figure 9b). These peaks are the contribution from Na 2p2p and O 2p2p states (see Figure 10b). Formation of the surface provides to the increasing of the number states near the edge of valence bands of Y2O3Y_2O_3 (see Figure 6) and peaks which are related with interstitial sodium and oxygen impurities disappear as separate features of the spectra.

Since lattice distortion caused by the formation of surface provides larger impact on electronic structure of both studied phases of Y2O3Y_2O_3, we also considered the influence of uniaxial expansion and compression on electronic structure of both bulk and surface Y2O3Y_2O_3. As a case study we used monoclinic phase of Y2O3Y_{2}O_{3}. In order to obtain more vivid effect we simulated rather large distortion of the lattice – at least 5%. Uniaxial expanding of Y2O3Y_{2}O_{3} lattice leads to an increase in the bandgap by approximately 1 eV and narrowing of the valence band (see Figure 11a). Note that the position of VBM remains unchanged and narrowing of VB is provided by elimination of VB split of (see area around -3 eV in Figure 11a). Contrary, uniaxial compression of lattice leads to a decrease of the bandgap by 1.2 eV and widening of VB by increasing of split between the peaks. Electronic structure transformations are less valuable in the case of uniaxial distortions of Y2O3Y_{2}O_{3} surface (Figure 11b). In the case of uniaxial expanding only minor changes in the heights of the peaks can be observed. Compression the slab leads to similar minor redistribution of peaks heights and also results in decreasing of bandgap by value of 0.4 eV. Note that the magnitude of distortions used in these simulations is larger than that for lattice parameters caused by mismatch between lattice parameters of substrate and surface layers or some local distortions. Thus, we can omit strain effect on electronic structure and optical properties of realistic samples of Y2O3Y_{2}O_{3} for discussion. On the other hand, the simulations performed demonstrate crucial role of symmetry in Y2O3Y_{2}O_{3} electronic structure breaking process.

Total densities of states of bulk and surface $Y_2O_3$ under uniaxial strain

Figure 11. Total Densities of States (DOS) of unstrained (black lines), uniaxialy expanded by 5% (red lines) and uniaxialy compressed at 5% (green lines) bulk (a) and slab (b) of Y2O3Y_2O_3 in monoclinic phase.

Summarizing theoretical part, we can conclude that electronic structure of bulk and surface Y2O3Y_{2}O_{3} is almost the same both for cubic and monoclinic phases. Neither stable adsorption of CO – CO2_{2} nor formation of defects provides visible changes in electronic structure of the surface for inspected phases. The main source of electronic structure variations for these structural phases of Y2O3Y_{2}O_{3} is established symmetry violation in vicinity of surface. The latter provides energy levels splitting and bands broadening.

Optical absorption and luminescence: bandgaps and excitonic states

Figure 12 shows optical absorption spectra of cubic and monoclinic Y2O3Y_{2}O_{3} layers in the Tauc coordinates for direct allowed interband transitions. The band gap was determined to be 5.76 eV and 6.12 eV for cubic and monoclinic Y2O3Y_{2}O_{3} films, respectively, using the Tauc equation (α⋅hν)n=A⋅(hν−Eg)(\alpha\cdot h\nu)^{n}=A\cdot(h\nu-E_{g}), where AA is a constant, α\alpha denotes absorption coefficient, hνh\nu is photon energy, EgE_{g} is optical band gap and nn is the exponent depending on the type of transitions (n=2n=2 for direct allowed transitions [39]). It is known that for bulk cubic yttrium oxide the band gap is 6.0 eV [40]. Comparing the film and bulk forms of cubic yttrium oxide, it can be seen that the band gap for the film is somewhat smaller than for the bulk analog. We suppose that the cause of this discrepancy is due to the difference in the electronic structure of the bulk and surface Y2O3\mathrm{Y}_2\mathrm{O}_3. As shown in Figure 9, in the electronic structure of Y2O3\mathrm{Y}_2\mathrm{O}_3 surface, there is a splitting of levels and a broadening of the valence and conduction bands compared to the electronic structure of bulk Y2O3\mathrm{Y}_2\mathrm{O}_3. This surface effect explains the observed narrowing of the band gap for cubic Y2O3\mathrm{Y}_2\mathrm{O}_3 film compared to the bulk analog. Unfortunately, there is no information on the band gap for bulk monoclinic Y2O3\mathrm{Y}_2\mathrm{O}_3 due to the technological complexity of preparing a single-phase sample with a monoclinic structure. However, based on the theoretical data shown in § 3.2, we can assume the similar trend in the band gap difference between the bulk material and the layers for monoclinic yttrium oxide.

Optical absorption spectra of cubic and monoclinic $\mathrm{Y}_2\mathrm{O}_3$ layers

Figure 12. Optical absorption spectra of cubic and monoclinic Y2O3\mathrm{Y}_2\mathrm{O}_3 layers in the Tauc coordinates for direct transitions. Red lines show approximation of linear ranges of spectra to determine the band gaps with an accuracy of ±0.01\pm0.01 eV. Arrow indicates band gap (6.0 eV) for bulk cubic Y2O3\mathrm{Y}_2\mathrm{O}_3. The inset shows an enlarged fragment of the spectra with band at 5.0 eV associated with exciton absorption.

Figure 13 shows normalized emission and excitation spectra of cubic and monoclinic Y2O3\mathrm{Y}_2\mathrm{O}_3 layers. Excitation bands at 4.96 eV (for monoclinic Y2O3\mathrm{Y}_2\mathrm{O}_3) and 5.00 eV (for cubic Y2O3\mathrm{Y}_2\mathrm{O}_3) are associated with exciton absorption [23, 24]. It is known that the formation of exciton occurs due to absorbed photons with energy of 6.0 eV for the bulk cubic Y2_2O3_3 [41]. According to our findings, exciton absorption band for cubic Y2_2O3_3 layers is shifted to the low-energy region if compared with that for the bulk Y2_2O3_3. We believe that such a difference in spectral position of exciton absorption band for the layers and bulk forms of Y2_2O3_3 can be associated with differences in their electronic structure, as it was shown by theoretical modeling (namely, with the broadening of the valence and conduction bands, see Figure 9).

Excitons-related normalized spectra for cubic and monoclinic Y2O3 layers

Figure 13. Excitons-related normalized spectra for cubic and monoclinic Y2_2O3_3 layers.

Emission spectra of both monoclinic and cubic Y2_2O3_3 layers are non-elementary and are represented by a superposition of two bands. The main contribution to emission spectra of monoclinic and cubic Y2_2O3_3 layers comes from the bands located at 3.13 eV and 3.27 eV, respectively (see Figure 13). These emission bands are associated with radiative de-excitation of the self-trapped exciton [24, 42, 43]. Note also that for bulk Y2_2O3_3 the exciton emission band is shifted to the high-energy region (3.4-3.5 eV) [41]. The luminescence spectra of the layers also exhibit weak bands at 2.8 eV (for monoclinic phase) and 3.0 eV (for cubic phase). The origin of these bands was interpreted as radiative recombination of the bound exciton localized on the anion vacancy center [23, 24]. Comparing the spectra in Figure 13, one can see that the spectral characteristics of the excitation-luminescence of layers with cubic and monoclinic structures are quite close to each other. This can be explained by the fact that electronic structure of Y2O3Y_2O_3 is almost the same for cubic and monoclinic phase.

The obtained experimental data are in full agreement with results of theoretical modeling.

The splitting of valence band energy levels observed in the electronic structure of surface Y2O3Y_2O_3 with monoclinic and cubic structures is associated with the contribution of surface states. In our case the objects under study are nanocrystalline layers with high surface-to-volume ratio, therefore an additional contribution to the formation of surface states can also be made by grain boundaries. As shown by optical spectroscopy data, differences in the electronic structure of bulk and surface Y2O3Y_2O_3 are reflected both in the band gap and in the luminescence characteristics. The revealed surface states can affect the ratio of the probabilities of radiative and nonradiative transitions in thin Y2O3Y_2O_3 layers doped with rare earth activator ions.

Conclusions

Results of comprehensive experimental and theoretical studies of nano–crystalline (average size of grains about 1010–1414 nm) Y2O3Y_2O_3 layers demonstrate insignificant difference in electronic structure and optical properties between two crystallographic phases (cubic and monoclinic). Note that the properties of monoclinic Y2O3Y_2O_3 have not been studied before in details. Neither intrinsic (oxygen vacancies and interstitials) nor extrinsic (Na-impurities used for stabilization of monoclinic phase or carbon mono- and dioxide adsorbed on the surface) defects does not provide valuable contribution in electronic structure and optical properties. Contrary, local distortion and symmetry breaking caused by formation of the surfaces leads to splitting of the energy levels in valence and conductive bands that reduce the bandgap and increase the number of possible optical transition, which is corresponding with changes in emission and adsorption spectra. Form the other hand, the absence of valuable contribution from defects in optical spectra agrees with narrow adsorption and emission peaks.

Electronic structures and optical properties of both Y2O3Y_2O_3 phases are almost identical, discussed in this work nanocrystalline layers of yttrium oxides could be grown on any chosen substrate without valuable variations of properties. Note that even huge strain (compression or expanding of the lattice at 5%) does not induce valuable changes in electronic structure of nanocrystalline Y2O3Y_2O_3. The very high energy cost of intrinsic defects formation, negligible influence of intrinsic and extrinsic defects on electronic structure in combination with surface stability toward oxidation and carbon monoxide poisoning yields nanocrystalline Y2O3Y_{2}O_{3} films prospective material for light detection and conversion of electromagnetic energy.

Acknowledgements

The work has been supported by the Russian Science Foundation (project № 21-12-00392).

References

  1. [1]A. Rastogi, R. Sharma, Structural and electrical characteristics of metal-insulator-semiconductor diodes based on Y₂O₃ dielectric thin films on silicon, J. Appl. Physics 71 (1992) 5041-5052. https://doi.org/10.1063/1.350605
  2. [2]S. Zhang, R. Xiao. Yttrium oxide films prepared by pulsed laser deposition, Journal of Applied Physics, 83 (1998) 3842. https://doi.org/10.1063/1.366615
  3. [3]F. Lu, H. Guo, S. Guo, Q. He, C. Li, W. Tang, G. Chen. Magnetron sputtered oxidation resistant and antireflection protective coatings for freestanding diamond film IR windows, Diamond and Rel. Materials 18 (2009) 244. https://doi.org/10.1016/j.diamond.2008.09.008
  4. [4]P.S. Das, G.K. Dalapati, D.Z. Chi, Characterization of Y₂O₃ gate dielectric on n-GaAs substrates, Appl. Surf. Sci. 256 (2010) 2245.https://doi.org/10.1016/j.apsusc.2009.10.046
  5. [5]R.L. Mehan, M.R. Jackson, M.D. Mcconnell. The use of Y₂O₃ coatings in preventing solid-state Si-base ceramic/metal reaction, J. Mater. Sci. 18 (1983) 3195. https://doi.org/10.1007/BF00544143
  6. [6]F. Yan, Z.T. Liu, W.T. Liu. The properties of the Y₂O₃ films exposed at elevated temperature, Physica B: Condens. Matt. 406 (2011) 2827.https://doi.org/10.1016/j.physb.2011.04.037
  7. [7]D. Nunes, A. Pimentel, M. Matias, T. Freire, A. Araújo, F. Silva, P. Gaspar, S. Garcia, P. A. Carvalho, E. Fortunato, R. Martins. Tailoring Upconversion and Morphology of Yb/Eu Doped Y₂O₃ Nanostructures by Acid Composition Mediation, Nanomaterials 9 (2019) 234. https://doi.org/10.3390/nano9020234
  8. [8]C. Ma, X. Li, M. Zhang, S. Liu, J.-G. Li, X. Sun. Synthesis of equal-sized Y₂O₃:Bi,Eu mono-spheres and their color-tunable photoluminescence and thermal quenching properties, Ceram. Int. 44 (2018) 18462. https://doi.org/10.1016/j.ceramint.2018.07.064
  9. [9]J. Petry, R. Komban, C. Gimmler, H. Weller. Simple one pot synthesis of luminescent europium doped yttrium oxide Y₂O₃:Eu nanodiscs for phosphor converted warm white LEDs, Nanoscale Adv. 4 (2022) 858. https://doi.org/10.1039/D1NA00831E
  10. [10]J.L. Ferrari, M.A. Schiavon, R.R. Gonçalves, A.M. Pires, M.R. Davolos. Film based on Y₂O₃:Eu³⁺ (5 mol% of Eu³⁺) for flat panel display, Thin Solid Films 524 (2012) 299. https://doi.org/10.1016/j.tsf.2012.08.016
  11. [11]H.M. Oh, H.N. Kim, Y.J. Park, J.W. Ko, H.K. Lee, S.J. Hwang, T.J. Yu. Optical properties and laser performance of Nd:Y₂O₃ ceramics with fine-grained microstructure, J. European Ceram. Soc. 41 (2021) 4419. https://doi.org/10.1016/j.jeurceramsoc.2021.02.024
  12. [12]F.L. Chawaram b wa, T.E. Putri, K. Kamataki, M. Shiratani, K. Koga, N. Itagaki, D. Nakamura. Synthesis of Yb³⁺/Ho³⁺ co-doped Y₂O₃ nanoparticles and its application to dye sensitized solar cells, J. Mol. Struct. 1228 (2021) 129479. https://doi.org/10.1016/j.molstruc.2020.129479
  13. [13]D. Chávez-García, P. Sengar, K. Juárez-Moreno, D.L. Flores, I. Calderón, J. Barrera, G.A. Hirata. Luminescence properties and cell uptake analysis of Y₂O₃:Eu, Bi nanophosphors for bio-imaging applications, J. Mater. Res. Technol. 10 (2021) 797. https://doi.org/10.1016/j.jmrt.2020.11.071
  14. [14]M. Zinkevich. Thermodynamics of rare earth sesquioxides, Prog. Mater. Sci. 52 (2007) 597. https://doi.org/10.1016/j.pmatsci.2006.09.002
  15. [15]P.P. Bose, M. Gupta, R. Mittal, S. Rols, S. Achary, A. Tyagi, S. Chaplot. Phase transitions and thermodynamic properties of yttria, Y₂O₃: Inelastic neutron scattering shell model and first-principles calculations, Phys. Rev. B 84 (2011) 094301. https://doi.org/10.1103/PhysRevB.84.094301
  16. [16]I. Halevy, R. Carmon, M.L. Winterrose, O. Yeheskel, E. Tiferet, S. Ghose. Pressure-Induced Structural Phase Transitions in Y₂O₃ Sesquioxide, Journal of Physics: Conference Series 215 (2010) 012003. https://doi.org/10.1088/1742-6596/215/1/012003
  17. [17]P. Yu, K. Zhang, S. Du, P. Ren, M. Wen, W. Zheng. Structure stability and Mechanical property of Y₂O₃ thin films deposited by reactive magnetron sputtering, Materials Science Forum 898 (2017) 1516. https://doi.org/10.4028/www.scientific.net/MSF.898.1516
  18. [18]C. Hua, C. Li, J. Guo, X. Yan, J. Liu, L. Chen, J. Wei, L. Hei. Optical properties of cubic and monoclinic Y₂O₃ films prepared through radio frequency magnetron sputtering, Surf. Coat. Technol. 320 (2017) 279. https://doi.org/10.1016/j.surfcoat.2017.01.004
  19. [19]W. van Schaik, G. Blasse. Influence of defects on the luminescence quantum yield of Y₁.₉₄Eu₀.₀₆O₃, Chem. Mater. 4 (1992) 410. https://doi.org/10.1021/cm00020a033
  20. [20]H. Choi, S.H. Cho, S. Khan, K.-R. Lee, S. Kim. Roles of an oxygen Frenkel pair in the photoluminescence of Bi3+-doped Y 2 O 3: computational predictions and experimental verifications, J. Mater. Chem. C2 (2014) 6017. https://doi.org/10.1039/c4tc00438h
  21. [21]P. Yu, K. Zhang, H. Huang, M. Wen, Q. Li, W. Zhang, C. Hu, W. Zheng. Oxygen vacancies dependent phase transition of Y₂O₃ films, Appl. Surf. Sci. 410 (2017) 470. https://doi.org/10.1016/j.apsusc.2017.03.145
  22. [22]N. Dhananjaya, H. Nagabhushana, B.M. Nagabhushana, B. Rudraswamy, C. Shivakumara, R.P.S. Chakradhar. Effect of Li⁺-ion on enhancement of photoluminescence in Gd₂O₃:Eu³⁺ nanophosphors prepared by combustion technique, J. Alloys Compd. 509 (2011) 2368-2374. https://doi.org/10.1016/j.jallcom.2010.11.023
  23. [23]A.F. Zatsepin, Yu.A. Kuznetsova, D.A. Zatsepin, C.H. Wong, W.C. Law, C.Y. Tang, N.V. Gavrilov, Exciton luminescence and optical properties of nanocrystalline cubic Y₂O₃ films obtained by reactive magnetron sputtering, Nanomaterials, In Press.
  24. [24]Yu.A. Kuznetsova, D.A. Zatsepin, A.F. Zatsepin, N.V. Gavrilov, Temperature-dependent luminescence of intrinsic defects and excitons in nanocrystalline monoclinic Y₂O₃ films, J. Lumin. 250 (2022) 119102. https://doi.org/10.1016/j.jlumin.2022.119102.
  25. [25]Detailed description of ThermoScientific K-alpha Plus XPS spectrometer is available at.: https://xpssimplified.com/kalpha_surface_analysis.php, accessed 30 June 2022
  26. [26]A.V. Naumkin, A. Kraut-Vass, S.W. Gaarenstroom, C.J. Powell. NIST XPS Standard Reference Database 20, version 4.1, © 2012, accessed 30 June 2022, doi: 10.18434/T4T88K, https://srdata.nist.gov
  27. [27]B.V. Crist. Handbook of Monochromatic XPS Spectra: The Elements of Native Oxides, Ed.: John Wiley & Sons LTD, NY, USA, ISBN: 978-0-471-49265-8 (2000) 548 p.
  28. [28]X. Zhang, Z. Li, Y. Peng, W. Su, X. Sun, J. Li, Investigation on a novel CaO-Y₂O₃ sorbent for efficient CO₂ mitigation, Chem. Eng. J. (Lausanne) 243 (2014) 297–304, https://doi.org/10.1016/j.cej.2014.01.017
  29. [29]ThermoScientific XPS: Knowledge Base, accessed 27 June 2022, https://www.thermofisher.com/ru/ru/home/materials-science/learning-center/periodic-table/transition-metal/yttrium.html, 2013–2022
  30. [30]Y. Pengfei, Z. Kan, H. Hao, W. Mao, L. Quan, Z. Wei, H. Chaoquan, Z. Weitao, Oxygen vacancies dependent phase transition of Y2O3 films, Appl. Surf. Sci. 410 (2017) 470–478, https://doi.org/10.1016/j.apsusc.2017.03.145
  31. [31]X. Zhang, Z. Li, Y. Peng, W. Su, X. Sun, J. Li, Investigation on a novel CaO-Y2O3 sorbent for efficient CO2 mitigation, Chem. Eng. J. (Lausanne) 243 (2014) 297–304, https://doi.org/10.1016/j.cej.2014.01.017
  32. [32]P. Giannozzi, et. al., Advanced capabilities for materials modelling with Quantum ESPRESSO. J.Phys.: Condens.Matter 29 (2017) 465901.https://doi.org/10.1088/1361-648X/aa8f79
  33. [33]J.P. Perdew, K. Burke, M. Ernzerhof. Generalized Gradient Approximation Made Simple, Phys. Rev. Lett. 77 (1996) 3865. https://doi.org/10.1103/PhysRevLett.77.3865
  34. [34]D. Vanderbilt, Soft Self-Consistent Pseudopotentials in a Generalized Eigenvalue Formalism,' Phys. Rev. B 41 7892 (1990). https://doi.org/10.1103/PhysRevLett.91.126402
  35. [35]H. Rydberg, M. Dion, N. Jacobson, E. Schröder, P. Hyldgaard, S. I. Simak, D. C. Langreth, B.I. Lundqvist, Van der Waals density functional for layered structures. Phys. Rev. Lett. 91 (2003) 126402. https://doi.org/10.1103/PhysRevLett.91.126402
  36. [36]L. Zhu, Q. Lu, L. Lv, Y. Wang, Y. Hu, Z. Deng, Z. Lou, Y. Hou, F. Teng. Ligand-free rutile and anatase TiO₂ nanocrystals as electron extraction layers for high performance inverted polymer solar cell, RCS Advances 7 (2017) 20084.DOI
  37. [37]Thermo Scientific XPS: Knowledge Base, © 2013–2021, accessed 2022-07-11, https://www.thermofisher.com/ru/ru/home/materials-science/learning-center/periodic-table/non-metal/carbon.html
  38. [38]Atomic Calculation of Photoionization Cross-Sections and Asymmetry Parameters (Web-version), Elettra, Italy; © 2015–2021, accessed 2022-07-12, https://vuo.elettra.eu/services/elements/WebElements.html
  39. [39]J. Tauc, Amorphous and Liquid Semiconductors, Plenum, New York, 1974.DOI
  40. [40]J. Robertson. Band offsets of wide-band-gap oxides and implications for future electronic devices, Journal of Vacuum Science & Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena 18 (2000) 1785. https://doi.org/10.1116/1.591472
  41. [41]A. Lushchik, M. Kirm, Ch. Lushchik, I. Martinson, G. Zimmerer, Luminescence of free and self-trapped excitons in wide-gap oxides, J. Lumin. 87–89 (2000) 232-234. https://doi.org/10.1016/S0022-2313(99)00271-9
  42. [42]D. den Engelsen, G. R. Fern, T. G. Ireland, P. G. Harris, P. R. Hobson, A. Lipman, R. Dhillon, P. J. Marsh and J. Silver, Ultraviolet and blue cathodoluminescence from cubic Y₂O₃ and Y₂O₃:Eu³⁺ generated in a transmission electron microscope, J. Mater. Chem. C 4 (2016) 4 7026-7034. https://doi.org/10.1039/c6tc01750a
  43. [43]D. den Engelsen, G.R. Fern, T. G. Ireland, J. Silver, Cathodoluminescence of Y₂O₃:Ln³⁺ (Ln = Tb, Er and Tm) and Y₂O₃:Bi³⁺ nanocrystalline particles at 200 keV, RSC Adv. 8 (2018) 396-405. https://doi.org/10.1039/C7RA12644A.

Paper details

vlnc:W_jcd4utf5
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents