betaFeedback

WorksPhysics and Astronomy

Symmetry-governed nonlinear metasurface simultaneously enhances circular dichroism, helicity purity, and Q-factor

Abstract

Circularly polarized light underpins a broad range of chiroptical and spin-selective photonic technologies, yet extending resonant chirality to nonlinear harmonic emission remains challenging. Here, we experimentally demonstrate a symmetry-governed mechanism that maps the maximal linear chirality of high-Q degenerate resonances onto the polarization of the generated harmonic. Preserved rotational symmetry protects modal degeneracy and polarization-selection rules, while broken mirror symmetries enable a strong chiroptical response. The metasurface thereby filters the pump polarization and purifies the handedness of the nonlinear output, simultaneously achieving third-harmonic circular dichroism of -0.98, a degree of circular polarization of 0.83, and an effective nonlinear Q-factor of 140. Importantly, the nonlinear emission preserves its handedness even under spatially depolarized excitation, demonstrating robustness to variations in the incident polarization state. These results establish complementary symmetry preservation and breaking as a deterministic route for transferring resonant chirality from linear to nonlinear optical responses, providing a general design principle for nonlinear chiral photonics.

Circularly polarized (CP) light plays a central role in modern photonics, being a key element of chiroptical spectroscopy[1, 2], spin–orbit photonics[3, 4], spintronics[5], and quantum optics[6]. The growing demand for compact, on-chip sources of CP radiation has sparked a rapid development of chiral metasurfaces: nanostructured optical devices capable of tailoring light’s handedness[7, 8], emission direction[9, 10, 11], and angular momentum[12, 13]. Chiral metasurfaces have been used in a variety of applications, such as the creation of single-handed optical cavities[14], spin multiplexing of single photons[15], chiral lasing[16, 17, 18, 19, 20], and spin-direction-locked emission[9, 21].

While these advances exploit linear light-matter interactions to control polarization and emission, extending such control into the nonlinear regime remains a major challenge. In this context, dielectric nonlinear metasurfaces[22, 23, 24, 25] have emerged as ultra-thin photonic platforms for frequency conversion, where strong resonant field enhancement due to high-QQ resonant modes enables efficient generation of the second[26, 27, 28], third[29, 30, 31], and higher harmonics[32, 33] within patterned slabs of subwavelength thickness. Despite the recent progress in conversion efficiency[28], mastering the chirality of nonlinear radiation remains an outstanding challenge. Importantly, while early nonlinear metasurfaces made of plasmonic materials demonstrated efficient polarization control[34, 35, 36], they suffered from strong ohmic losses, were limited in the conversion efficiency, and relied on surface-induced nonlinearity. Unlike in plasmonic metasurfaces, harmonic generation in dielectric metasurfaces arises from near fields with complex spatial structure within the volume of the nonlinear material. Such volume nonlinear response depends sensitively on geometry, material properties, and fabrication imperfections. Accordingly, most nonlinear chiral devices developed to date operate based on two main physical mechanisms.

The first mechanism is the well-known symmetry selection rule, stating that metasurfaces exhibiting a proper rotational symmetry generate CP nonlinear signals under normally incident right- and left-circularly polarized (RCP and LCP) excitation[37, 38, 39, 40, 41]. Despite the ability to produce CP nonlinear outputs, such structures are inherently achiral, and the chirality of the nonlinear signal is strictly conditioned by the excitation chirality. The second mechanism, which forms the basis for devices known as nonlinear chiral metasurfaces, exploits a chiral resonance at the excitation frequency[42, 43, 44, 45]. Such resonances selectively couple to a specific CP excitation, producing near-field enhancement within the nonlinear material and generating a strong nonlinear signal. Excitation with the opposite CP, in contrast, produces only a weak, non-resonant output. Importantly, this handedness-dependent intensity asymmetry, commonly quantified by nonlinear circular dichroism, reflects only the difference in signal strength and does not convey information about the polarization state of the generated harmonic. At the same time, reduced symmetry of chiral metasurfaces does not provide any reliable mechanism for the polarization control of the nonlinear signal. The induced nonlinear near-fields, characterised by rapid spatial variations of magnitude, direction, and phase, result in the harmonic emission with arbitrary elliptical polarization. Consequently, no existing mechanism combines chirality with high-QQ resonances to deterministically generate nonlinear harmonics with helicity fixed over a broad family of input states.

Only recently have CP nonlinear signals from dielectric metasurfaces been observed under specific linearly polarized (LP) excitations[46, 47, 48], but these effects arise from accidental modal degeneracies at the harmonic frequency, leading to polarization states that depend sensitively on modal configuration and excitation polarization. As we proposed in Ref.[49], a deterministic route requires a symmetry-protected mechanism based on maximally chiral, high-QQ resonances in rotationally symmetric metasurfaces, where degenerate modes selectively couple to a chosen circular polarization and generate CP harmonics robustly. However, such resonances have been difficult to realize experimentally due to reliance on perfect vertical alignment in the double-layer geometry. On the other hand, existing demonstrations of high-QQ chiral resonances, particularly quasi-bound states in the continuum (quasi-BICs), typically rely on complete symmetry breaking[8, 19, 42, 50], which lifts degeneracy and precludes symmetry-protected polarization manipulation.

In this work, we overcome these limitations and enable practical implementations by introducing and experimentally verifying a symmetry-based mechanism for the generation of a chiral nonlinear signal, which can be interpreted as nonlinear transfer of resonant chirality. Our approach relies on a dielectric metasurface that combines nonlinearity-matching rotational symmetry with tailored mirror asymmetry to produce a pair of maximally chiral, high-QQ quasi-guided resonances, implemented in a flat, single-layer, CMOS-compatible silicon platform (Figure 1a,Figure 1b). The helicity-selective coupling of the degenerate resonance pair imprints a specific chiral phase pattern onto the fields induced at the pump frequency. This phase is transferred to the third harmonic (TH) polarization through the rotational-symmetry selection rules, resulting in CP nonlinear harmonic radiation. We demonstrate that devices built on this principle simultaneously achieve near-unity TH circular dichroism of −0.98, TH degree of circular polarization (DCP) of 0.83 and high QQ-factor controlled by the symmetry-breaking strength, thereby occupying a distinct performance regime in Figure 1c. Moreover, we demonstrate that TH response remains dominated by the selected CP even after the excitation beam is transformed by a liquid crystal depolarizer (Figure 1d). Establishing the symmetry-protected transfer of resonant chirality as a general design principle, this work lays the foundation for a new class of functional nonlinear devices with robust structurally-controlled polarization of nonlinear signal.

Nonlinear chirality transfer in flat dielectric metasurfaces

Figure 1. a, Symmetry-encoded chiral near-field pattern is transferred to the nonlinear polarization, enforcing robust generation of a circularly polarized TH signal. b, Scanning electron microscope image of the fabricated chiral metasurface. c, Quantitative comparison of experimental performance of all-dielectric nonlinear metasurfaces in terms of TH degree of circular polarization, nonlinear circular dichroism, and nonlinear Q-factor. Refs. [11, 42] (gray circles) do not report TH polarization. d, Comparison of the established approaches for nonlinear chirality and generation of chiral TH signal under excitation with a spatially varying polarization state.

Nonlinear chirality transfer mechanism

We consider a metasurface exhibiting fourfold rotational symmetry C4C_{4} of the meta-lattice made of materials with nonlinear response that is invariant under C4C_{4} (Figure 1a). The symmetry is chosen to demonstrate the effect for TH generation; however, the phenomenon is general and can be realized in systems with NN-fold rotational symmetry (N=3,4,6N = 3,4,6) for the (N−1)(N-1)th-order nonlinear process.

In structures with N≥3N \ge3, it is possible to identify pairs of degenerate resonant modes, whose degeneracy is protected by the rotational symmetry of the structure. In the particular case, a mode pair with electric fields E1(r),E2(r)\mathbf{E}_{1}(\mathbf{r}), \mathbf{E}_{2}(\mathbf{r}) form the real two-dimensional irreducible representation EE of the C4C_{4} point group, such that the two modes are converted into each other under a 90° rotation (Figure 1a, right side):

C^4E1(C^4−1r)=−E2(r),C^4E2(C^4−1r)=E1(r).(1)\hat{C}_{4}\mathbf{E}_{1}(\hat{C}_{4}^{-1}\mathbf{r}) = -\mathbf{E}_{2}(\mathbf{r}), \qquad\hat{C}_{4}\mathbf{E}_{2}(\hat{C}_{4}^{-1}\mathbf{r}) = \mathbf{E}_{1}(\mathbf{r}). \tag*{(1)}

As we show later, the far-field polarization of such modes can be controlled by means of geometric perturbations. Throughout this work, modal chirality refers specifically to the degree of circular polarization of the resonance's radiative far field (see Methods), quantified by S3S_{3}, rather than to local optical-chirality density. Once one of the modes is tuned to maximal chirality on the excitation side (LCP for definiteness), Eqs. (1) necessitate that the other mode exhibits the same polarization with a phase difference π/2\pi/2. Thus, under arbitrarily polarized excitation, both modes are excited with equal amplitudes proportional to the LCP component of the incident field while preserving the polarization-independent phase offset (see Methods). Assuming that the non-resonant response remains weak, the induced electric field at the pump frequency, given by the combination of excited resonant modes Eω(r)∝E1(r)−iE2(r)\mathbf{E}^{\omega}(\mathbf{r}) \propto\mathbf{E}_1(\mathbf{r}) - i\mathbf{E}_2(\mathbf{r}), features a highly symmetric field distribution with an imprinted chiral phase pattern:

C^4Eω(C^4−1r)=Eω(r)e−iπ/2.(2)\hat{C}_4\mathbf{E}^{\omega}\left(\hat{C}_4^{-1}\mathbf{r}\right) = \mathbf{E}^{\omega}(\mathbf{r})e^{-i\pi/2}. \tag*{(2)}

This response is fundamentally different from that of achiral C4vC_{4v} structures, where degenerate modes with orthogonal far-field polarizations produce markedly different near-field patterns under CP and LP excitation (see Supplementary Fig. S1).

Resonant field Eω(r)\mathbf{E}^{\omega}(\mathbf{r}) induces nonlinear polarization P3ω(r)=ε0χ(3)(r):Eω(r)3\mathbf{P}^{3\omega}(\mathbf{r}) = \varepsilon_0\chi^{(3)}(\mathbf{r}):\mathbf{E}^{\omega}(\mathbf{r})^3, which, due to the invariance under C4C_4 rotations, follows similar transformation rules:

C^4P3ω(C^4−1r)=P3ω(r)e−3iπ/2.(3)\hat{C}_4\mathbf{P}^{3\omega}\left(\hat{C}_4^{-1}\mathbf{r}\right) = \mathbf{P}^{3\omega}(\mathbf{r})e^{-3i\pi/2}. \tag*{(3)}

The phase factor e−3iπ/2e^{-3i\pi/2} is equivalent to eiπ/2e^{i\pi/2}; therefore, the nonlinear polarization transforms as an RCP-induced field and consequently radiates an RCP TH signal into the lower half-space (see Supplementary Section S1 for details).

As a consequence, the chirality of the linear resonant response enforces the chiral transformation rules for the induced electromagnetic fields E(r)\mathbf{E}(\mathbf{r}) under an arbitrarily polarized pump. This chirality is subsequently transferred to the nonlinear polarization. The net result is a robust generation of an RCP nonlinear signal whose intensity is controlled by the pump polarization (Figure 1a).

Degenerate high-Q chiral modes in a flat metasurface

Demonstration of nonlinear chirality transfer requires a degenerate pair of modes of maximal chirality and sufficient resonant-to-nonresonant enhancement. Chiral quasi-BICs, which combine ultrahigh-Q resonances with fully CP emission, have attracted considerable interest since their theoretical introduction several years ago by two groups[7, 50]. Subsequent experiments have demonstrated impressive Q-factors and near-perfect linear chiral response[8, 19]. However, reported realizations rely on slanted[51], multilayer[10], multi-height[52, 53], or even flat[42] architectures that break not only mirror but also rotational symmetries.

This reliance on asymmetric designs originates from fundamental symmetry selection rules[54, 55]. In structures with four-fold rotational symmetry, these rules prohibit the formation of quasi-BIC resonances at normal incidence: all non-degenerate modes become symmetry-protected BICs, while degenerate modes necessarily couple to free space. Consequently, realizing a transition from a BIC to a quasi-BIC requires breaking rotational symmetry. In contrast, rotational symmetry is essential in our work to enable nonlinear chiral effects, rendering the quasi-BIC approach fundamentally incompatible with our requirements. Instead, we exploit rotationally symmetric, degenerate quasi-guided modes[56], i.e., descendants of guided modes below the light line, which offer tunable high Q-factors[57] without sacrificing structural symmetry.

We introduce a general design principle for realizing degenerate high-QQ chiral modes through sequential symmetry breaking and illustrate it with the example shown in Figure 2. The initial structure, which supports guided modes, is shown in Figure 2a. It consists of cylindrical amorphous silicon pillars with radius RR and height HH, arranged in a square lattice on a SiO2\mathrm{SiO}_2 substrate with period p/2p/\sqrt{2}. While substrate-superstrate asymmetry has been shown to be essential for achieving a chiral response in rotationally symmetric structures, here we treat it as an inherent feature of a practically realizable metasurface[58]. The substrate is naturally retained to minimize fabrication complexity, and the design freedom is confined to the metasurface pattern. The corresponding modal dispersion is shown in Figure 2b, with the first Brillouin zone and its high-symmetry points defined in Figure 2c. Multiple modes appear near 200 THz at the Γ(1,0)\Gamma^{(1,0)} point below both the vacuum and substrate light lines. Owing to their large Bloch wavevectors, these modes lie outside the radiation continuum and therefore possess infinite QQ-factors.

Enabling degenerate high-$Q$ chiral modes via sequential symmetry breaking

Figure 2. a, Initial structure supporting nonradiative guided modes below the substrate light cone near 200 THz. b, Scattering-matrix norm revealing the modal dispersion; dashed lines indicate the air and substrate light cones. c, Brillouin-zone folding of the guided modes into the first Brillouin zone. High-symmetry points are labelled according to the perturbed reciprocal lattice. d, Perturbed structure with an enlarged unit cell containing a smaller central cylinder of radius RcR_{\mathrm{c}}. e, Dispersion of the resonant modes; the degenerate quasi-guided mode pair near 205 THz, arising from Brillouin-zone folding, is highlighted by the green circle. f, QQ factor of the degenerate quasi-guided modes as a function of the perturbation parameter RcR_{\mathrm{c}}. g, Metasurface with broken mirror symmetries hosting a pair of degenerate high-QQ chiral modes. h, Schematic of the symmetry-breaking process: larger circular pillars are transformed into elliptical ones. i, Evolution of the resonant electric-field distribution during the transition to chirality. j, Mode chirality, quantified by the far-field degree of circular polarization, obtained from COMSOL simulations (left) and predicted by the interface perturbation theory (right). k, Dispersion of the resonant modes near the Γ\Gamma point at 200 THz. Colour denotes chirality; the black star marks two degenerate modes with maximum chirality.

To enable free-space coupling, we perturb the structure by introducing additional smaller cylindrical pillars with radius RcR_{\mathrm{c}}, as shown in Figure 2d, thereby forming a larger unit cell with period pp. The expansion of the unit cell in real space results in Brillouin-zone folding in momentum space (Figure 2c), which maps the guided modes from Γ(1,0)\Gamma^{(1,0)} to the original Γ\Gamma point at normal incidence. This process gives rise to a family of quasi-guided modes near 200 THz, as shown in Figure 2e. Due to the symmetry-enforced degeneracy, such modes have been used to achieve pump-polarization-independent enhancement of the TH signal[59]; however, helicity control remained elusive. Similar to quasi-BICs, these modes can exhibit ultrahigh QQ-factors that are tunable via the perturbation strength (Figure 2f). Despite this similarity, quasi-guided modes are fundamentally distinct from quasi-BICs. In quasi-BIC systems, a radiative resonance persists in the dispersion even in the absence of perturbation and remains coupled to free space at oblique incidence. In contrast, the far-field coupling of quasi-guided modes vanishes throughout the entire momentum space as the perturbation strength approaches zero, as evident from Figure 2b.

We select a pair of degenerate quasi-guided modes near 205 THz, indicated by the green circle in Figure 2e. These modes are initially achiral because the structure preserves in-plane mirror symmetries. To induce chirality, we morph the larger circular pillars into elliptical ones with half-lengths R±ΔRR \pm\Delta R, rotated by an angle θ\theta (Figure 2g), thereby breaking all mirror symmetries and introducing geometric chirality. The resulting chiral optical response, however, depends sensitively on the perturbation parameters ΔR\Delta R and θ\theta. To analyze this dependence, we partition space into four regions defined by the permittivity distributions of the unperturbed structure ε(r)\varepsilon(\mathbf{r}) and the perturbed structure ε~(r)\tilde{\varepsilon}(\mathbf{r}) in Figure 2h. The regions UresU_{\mathrm{res}} and UbgU_{\mathrm{bg}} retain the same permittivities, εSi\varepsilon_{\mathrm{Si}} and εair\varepsilon_{\mathrm{air}}, before and after perturbation. In contrast, the regions δUres\delta U_{\mathrm{res}} and δUbg\delta U_{\mathrm{bg}} undergo permittivity exchange, switching from εair\varepsilon_{\mathrm{air}} to εSi\varepsilon_{\mathrm{Si}} and from εSi\varepsilon_{\mathrm{Si}} to εair\varepsilon_{\mathrm{air}}, respectively.

To predict the values of ΔR\Delta R and θ\theta that yield maximum resonance chirality, we employ a semi-analytical model based on a perturbative approach and Maxwell’s boundary conditions. At any material interface, the tangential components of the electric field and the normal components of the electric displacement field are continuous, i.e., E1∥=E2∥\mathbf{E}_{1\parallel}=\mathbf{E}_{2\parallel} and D1⊥=D2⊥\mathbf{D}_{1\perp}=\mathbf{D}_{2\perp}. As a result, the normal component of the electric field is discontinuous across Si–air boundaries. Small structural perturbations that shift these boundaries do not substantially modify the global field distribution, but they induce pronounced changes in the electric field within regions of altered permittivity, δUres\delta U_{\mathrm{res}} and δUbg\delta U_{\mathrm{bg}}, as can be seen in Figure 2i. Figure 2i shows the evolution of just one mode in the degenerate pair, which in the achiral structure (ΔR=0\Delta R=0 nm and θ=0∘\theta=0^\circ) exhibits pure xx-polarization. The second mode, being a 90∘90^\circ-rotated copy of the first mode, undergoes an identical transformation.

While boundary-shift corrections have been shown to be essential for accurately capturing the energy shifts of perturbed resonant modes[60, 61], we exploit them to evaluate the resonance far-field polarization and thus its chirality (see Methods for details). Essentially, the normal components of the resonant fields of the achiral structure are modified by the ratio of the permittivity distributions ε(r)/ε~(r)\varepsilon(\mathbf{r})/\widetilde{\varepsilon}(\mathbf{r}), such that the perturbed fields remain continuous wherever ε~(r)\widetilde{\varepsilon}(\mathbf{r}) is continuous and satisfy Maxwell’s boundary conditions at all interfaces of the perturbed structure. A comparison between the exact resonant mode chirality extracted from COMSOL eigenmode simulations (see Methods for details) for varying ΔR\Delta R, θ\theta and the semi-analytical calculations based on the perturbed resonant fields indicates good agreement, as shown in Figure 2j.

We choose a metasurface design with perturbation parameters ΔR=40\Delta R=40 nm and θ=28∘\theta=28^\circ, which correspond to the maximum chirality of the resonant mode. The resulting two-dimensional dispersion of modes near 200 THz is shown in Figure 2k. The modes of interest are degenerate at the Γ\Gamma point, are well separated from other bands, and exhibit near-flat dispersion. Importantly, they also display near-unity DCP over a substantial region of momentum space (indicated by colour in Figure 2k), providing ideal conditions for observing nonlinear chirality transfer. This mechanism is first validated in numerical simulations and subsequently demonstrated experimentally in a silicon-on-silica platform.

Numerical simulations of the nonlinear chirality transfer

Next, we analyse the linear and nonlinear optical responses of the metasurface tuned to exhibit maximum chirality with ΔR=40\Delta R=40 nm and θ=28∘\theta=28^\circ. Figure 3a,Figure 3b compares the linear transmission spectra TR,LT_{\mathrm{R,L}} under RCP and LCP excitation, together with the corresponding near-field enhancement spectra for both lossless and lossy structures. Remarkably, in the ideal lossless case, the resonant mode with maximal chirality is completely absent from the far-field scattering spectra. In contrast, the second resonant mode manifests as a sharp transmission dip but exhibits zero linear circular dichroism, defined as CD=(TR−TL)/(TR+TL)\mathrm{CD}=(T_{\mathrm{R}}-T_{\mathrm{L}})/(T_{\mathrm{R}}+T_{\mathrm{L}}). This behaviour arises from the combined constraints of reciprocity and rotational symmetry, as established in prior theoretical studies[7, 58].

Nonlinear chirality transfer and numerical modelling of the chiral metasurface

Figure 3. Nonlinear chirality transfer and numerical modelling of the chiral metasurface. a,b, Linear transmission and near-field enhancement spectra for lossless and lossy chiral metasurfaces. In both cases, the field enhancement is uniquely determined by the resonance chirality. c, Electric-field distributions at the resonant wavelength under resonant (LCP) and nonresonant (RCP) excitation. d, Schematic definition of the two key nonlinear figures of merit: nonlinear circular dichroism and the degree of circular polarization of the third-harmonic signal. e, Third-harmonic intensity and nonlinear CD spectra under CP and LP excitation. f, DCP of the generated TH signal under LCP, linear (LP), and RCP excitation. The spectral region where the TH intensity exceeds 25% of its maximum is highlighted by the yellow band. g, Poincaré sphere showing representative trajectories of the pump polarization from LCP to RCP. The shaded region indicates pump states that produce negligible TH intensity. h, TH intensity and DCP as functions of pump polarization along the trajectories shown in g.

Importantly, the absence of resonant features or linear CD in the scattering spectra does not imply suppression of the resonance or lack of polarization selectivity. On the contrary, the near-field intensity (Figure 3a, bottom panel; Figure 3c) reveals strong resonant enhancement with pronounced polarization dependence. When material losses are introduced to reach the criticalcoupling regime (extinction coefficient k=0.01k = 0.01) the same structure exhibits two prominent chiral resonances in transmission. While these losses maximize the depth of the resonant transmission dip, they have minimal impact on the resonance chirality and primarily reduce the near-field enhancement (Figure 3b, bottom panel). This observation suggests that in rotationally symmetric structures, strong nonlinear circular dichroism can emerge even in the absence of strong linear CD, which we also observe experimentally. We note that this mechanism is different from the nonlinearity-induced chirality observed in linearly achiral resonant metasurfaces[62].

Moving on to nonlinear effects, Figure 3d summarizes the two key measures of nonlinear chirality. First, we denote the RCP and LCP components of the generated TH signal under pump with polarization state sin\mathbf{s}^{\mathrm{in}} as Isin→R,L(3ω)I_{\mathbf{s}^{\mathrm{in}\to\mathrm{R,L}}}^{(3\omega)}. Nonlinear CD quantifies the dependence of the total TH intensity Itot(3ω)=IR(3ω)+IL(3ω)I_{\mathrm{tot}}^{(3\omega)} = I_{\mathrm{R}}^{(3\omega)} + I_{\mathrm{L}}^{(3\omega)} on the helicity of the incident field and is therefore obtained by comparing two separate measurements under RCP and LCP excitation:

CD(3ω)=IR→tot(3ω)−IL→tot(3ω)IR→tot(3ω)+IL→tot(3ω)=IR→R(3ω)+IR→L(3ω)−IL→R(3ω)−IL→L(3ω)IR→R(3ω)+IR→L(3ω)+IL→R(3ω)+IL→L(3ω).(4)\mathrm{CD}^{(3\omega)} = \frac{I_{\mathrm{R}\to\mathrm{tot}}^{(3\omega)} - I_{\mathrm{L}\to\mathrm{tot}}^{(3\omega)}}{I_{\mathrm{R}\to\mathrm{tot}}^{(3\omega)} + I_{\mathrm{L}\to\mathrm{tot}}^{(3\omega)}} = \frac{I_{\mathrm{R}\to\mathrm{R}}^{(3\omega)} + I_{\mathrm{R}\to\mathrm{L}}^{(3\omega)} - I_{\mathrm{L}\to\mathrm{R}}^{(3\omega)} - I_{\mathrm{L}\to\mathrm{L}}^{(3\omega)}}{I_{\mathrm{R}\to\mathrm{R}}^{(3\omega)} + I_{\mathrm{R}\to\mathrm{L}}^{(3\omega)} + I_{\mathrm{L}\to\mathrm{R}}^{(3\omega)} + I_{\mathrm{L}\to\mathrm{L}}^{(3\omega)}}. \tag*{(4)}

Without additional symmetry constraints, nonlinear CD merely describes how strongly the nonlinear conversion efficiency depends on the incident helicity but does not specify the polarization state of the generated TH signal. As one can see, near-unitary CD(3ω)\mathrm{CD}^{(3\omega)} can be achieved even when the generated TH is linearly polarized, e.g. when IR→R(3ω)=IR→L(3ω)≫IL→L,R(3ω)I_{\mathrm{R}\to\mathrm{R}}^{(3\omega)} = I_{\mathrm{R}\to\mathrm{L}}^{(3\omega)} \gg I_{\mathrm{L}\to\mathrm{L,R}}^{(3\omega)}. We demonstrate that such behaviour is ubiquitous by considering the nonlinear response of some well-known chiral metasurfaces[11, 42] in Supplementary Section S2.

On the contrary, the TH DCP, which quantifies the helicity purity, characterizes the polarization state of the generated nonlinear signal and is defined using the RCP and LCP TH components Isin→R,L(3ω)I_{\mathbf{s}^{\mathrm{in}}\to\mathrm{R,L}}^{(3\omega)}, produced in a single experiment under a fixed excitation state sin\mathbf{s}^{\mathrm{in}}:

DCP(3ω)≡S3(3ω)=Isin→R(3ω)−Isin→L(3ω)Isin→R(3ω)+Isin→L(3ω).(5)\mathrm{DCP}^{(3\omega)} \equiv S_{3}^{(3\omega)} = \frac{I_{\mathbf{s}^{\mathrm{in}}\to\mathrm{R}}^{(3\omega)} - I_{\mathbf{s}^{\mathrm{in}}\to\mathrm{L}}^{(3\omega)}}{I_{\mathbf{s}^{\mathrm{in}}\to\mathrm{R}}^{(3\omega)} + I_{\mathbf{s}^{\mathrm{in}}\to\mathrm{L}}^{(3\omega)}}. \tag*{(5)}

Thus, nonlinear CD is an input-helicity contrast, while TH DCP is the direct measure of output helicity. Nonlinear chirality transfer bridges these two key measures by suppressing TH generation under pump with resonant-mismatching CP IR→tot(3ω)≪IL→tot(3ω)I_{\mathrm{R}\to\mathrm{tot}}^{(3\omega)} \ll I_{\mathrm{L}\to\mathrm{tot}}^{(3\omega)}, and simultaneously boosting the symmetry-selected RCP component of the TH signal Isin→R(3ω)≫Isin→L(3ω)I_{\mathbf{s}^{\mathrm{in}}\to\mathrm{R}}^{(3\omega)} \gg I_{\mathbf{s}^{\mathrm{in}}\to\mathrm{L}}^{(3\omega)}. In the following, we focus on the TH signal emitted into the main diffraction channel in transmission geometry under normal-incidence excitation from the air side.

To model the TH response of the metasurface (see Methods for details), we describe the nonlinear polarization of amorphous silicon using an isotropic third-order susceptibility, P3ω=χ(3)E(E⋅E)\mathbf{P}^{3\omega} = \chi^{(3)}\mathbf{E}(\mathbf{E} \cdot\mathbf{E}). Figure 3e shows the calculated TH intensity spectra under LCP, LP, and RCP excitation. A sharp resonance appears for both LCP and LP excitation. Notably, the peak TH intensity under LCP pumping is approximately eight times larger than that under LP excitation, since only half of the LP wave power couples to the chiral resonance. In contrast, RCP excitation produces a negligible TH response, leading to near-unity nonlinear CD over a broad wavelength range.

We next examine the polarization of the generated TH signal (Figure 3f). Under both RCP and LCP excitation, the emitted TH exhibits inverted circular polarization, independent of excitation wavelength, in accordance with symmetry selection rules. In contrast, the TH DCP under LP excitation shows a more intricate behaviour: it reaches near-unity values in the vicinity of the resonance, while outside the resonant region (highlighted by the yellow band in Figure 3e,Figure 3f), the TH signal is vanishingly weak. This behaviour indicates that an LP pump generates resonance-enhanced RCP TH emission.

To comprehensively characterize the TH output, we select seven representative trajectories on the Poincaré sphere that span the full space of pump polarizations (Figure 3g). The corresponding simulated TH intensity and DCP profiles along these paths are shown in Figure 3h. The results reveal a striking robustness of the TH polarization for all pump states that generate a non-negligible TH response.

Within the effective metamaterial susceptibility framework, the nonlinear response to a pump field with arbitrary polarization, expressed in the circular basis as sin=eRsR+eLsLeiΔϕ\mathbf{s}^{\mathrm{in}} = \mathbf{e}_{R}s_{R} + \mathbf{e}_{L}s_{L}e^{i\Delta\phi}, can be fully described by four nonzero components of the effective third-order susceptibility tensor χ(3,eff)\chi^{(3,\mathrm{eff})}. The intensities of the LCP and RCP TH components are given by

IL(3ω)∝∣χLRRR(3,eff)sR3+χLRLL(3,eff)sRsL2e2iΔϕ∣2,IR(3ω)∝∣χRRRL(3,eff)sR2sL+χRLLL(3,eff)sL3e2iΔϕ∣2.(6)\begin{aligned} I_{L}^{(3\omega)} &\propto\left|\chi_{LRRR}^{(3,\mathrm{eff})}s_{R}^{3}+\chi_{LRLL}^{(3,\mathrm{eff})}s_{R}s_{L}^{2}e^{2i\Delta\phi}\right|^{2},\\ I_{R}^{(3\omega)} &\propto\left|\chi_{RRRL}^{(3,\mathrm{eff})}s_{R}^{2}s_{L}+\chi_{RLLL}^{(3,\mathrm{eff})}s_{L}^{3}e^{2i\Delta\phi}\right|^{2}. \tag*{(6)} \end{aligned}

A detailed comparison between full-wave simulations and the effective susceptibility description is provided in the Supplementary Section S1. Here, we highlight the central result: at the chiral resonance, the relative magnitudes of the tensor components are ∣χLRRR(3,eff):χLRLL(3,eff):χRRRL(3,eff):χRLLL(3,eff)∣=1:35:28:268\left|\chi_{LRRR}^{(3,\mathrm{eff})}:\chi_{LRLL}^{(3,\mathrm{eff})}:\chi_{RRRL}^{(3,\mathrm{eff})}:\chi_{RLLL}^{(3,\mathrm{eff})}\right|=1:35:28:268, while all other components of χ(3,eff)\chi^{(3,\mathrm{eff})} vanish due to the rotational symmetry. Because the resonance selectively couples to and amplifies only the LCP component of the pump, the TH intensity is primarily governed by the pump DCP. The weak intensity variations observed along different trajectories on the Poincaré sphere arise from interference with nonresonant, RCP-induced fields. Dominated by the χRLLL(3,eff)\chi_{RLLL}^{(3,\mathrm{eff})} component, the generated TH signal remains nearly perfectly RCP (S3(3ω)>0.83S_{3}^{(3\omega)}>0.83) for all pump polarizations spanning the lower three-quarters of the Poincaré sphere.

This behavior constitutes the all-to-circular upconversion effect predicted in our previous work[49], here realized in a flat, single-layer CMOS-compatible metasurface, representing a highly fabrication-feasible platform.

Experimental observation of the nonlinear chirality transfer

The chiral metasurface was fabricated using electron-beam lithography followed by inductively coupled plasma reactive-ion etching (see Methods for details). A scanning electron microscope image of the fabricated sample is shown in Figure 1b. To visualise the modal dispersion, we measured the linear transmission spectra under CP excitation, which are shown in Figure 4a. All measurement details are provided in the Methods section. One can identify two modes that become degenerate at the Γ\Gamma-point at 1435 nm. Due to their chirality, the modes only appear as a resonant dip under LCP excitation, while almost vanishing from the RCP transmission. These spectra agree well with the numerically simulated results, shown in Supplementary Fig. S4. Transmission spectra at normal incidence under LCP, LP, and RCP excitation (Figure 4b) measured using a home-built low-NA transmission microspectroscopy system reveal a pronounced chiral resonance with a Q-factor of 127.

Experimental demonstration of nonlinear chirality transfer

Figure 4. Experimental demonstration of nonlinear chirality transfer. a, Angle-resolved linear transmission spectra under RCP and LCP pump. b, Linear transmission spectra at normal incidence under LCP, LP, and RCP excitation. c, Measured TH intensity and corresponding nonlinear CD as functions of the pump wavelength. d, Measured DCP of the TH signal under LCP and LP excitation. The wavelength range where the TH intensity exceeds 25% of its maximum is highlighted by the yellow band. e,f, Intensities of the LCP (red) and RCP (blue) components of the TH signal, together with the TH degree of circular polarization (black). Pump polarization follows Poincaré sphere meridians passing through xx- and yy-polarizations. g, Intensity of RCP and LCP components of the TH signal, together with the TH DCP under 1435 nm spatially depolarized excitation. h, Intensity of RCP and LCP TH components, together with the TH DCP under depolarized excitation as a function of pump wavelength. i, Total power of the depolarized beam transmitted through a linear polarizer as a function of the rotation angle of the depolarizer. j, TH signal DCP under depolarized excitation as a function of the rotation angle of the depolarizer.

To further validate the TH generation performance of the Si metasurface, a polarization-resolved measurement system was constructed using a near-infrared wavelength-tunable femtosecond laser. The experimentally measured TH signals (Figure 4c) show good agreement with the simulations in Figure 3e. Under LCP and LP excitation, the TH intensity as a function of the pump wavelength shows a resonant peak with a full width at half-maximum of Δλ(I3ω)=10\Delta\lambda(I^{3\omega}) = 10 nm, which corresponds to the effective nonlinear Q-factor QNL,eff=λΔλ(I3ω)≈140Q^{NL,\mathrm{eff}} = \frac{\lambda}{\Delta\lambda(I^{3\omega})} \approx140, where λ\lambda is the pump wavelength. At the same time, the resonant-to-nonresonant intensity ratios (at λ=1435\lambda= 1435 nm and λ=1407\lambda= 1407 nm) exceed 100 and 35 for LCP and LP pump, respectively.

In contrast, RCP excitation produces a negligible TH signal. This pronounced asymmetry gives rise to a near-unity nonlinear circular dichroism of CD(3ω)=−0.98\mathrm{CD}^{(3\omega)}=-0.98. The measured DCP of the nonlinear signal (Figure 4d) confirms the helicity-inversion effect under LCP pumping with good quantitative agreement: the TH DCP reaches S3(3ω)=0.83S_{3}^{(3\omega)}=0.83 at resonance. The experimentally observed deviation of S3(3ω)S_{3}^{(3\omega)} from unity can be attributed to fabrication-induced symmetry breaking, as well as to deviations of the excitation beam from an ideal circularly polarized plane wave. Under LP excitation, the DCP clearly approaches that obtained under LCP pumping, reaching S3(3ω)=0.66S_{3}^{(3\omega)}=0.66 at resonance. Thus, the generation of a highly CP TH signal is consistently observed across the entire resonant band.

Next, we experimentally characterize the nonlinear response along two representative meridians on the pump-polarization Poincaré sphere. To probe the meridians of the sphere, the pump light is passed through a linear polarizer followed by a quarter-wave plate (QWP). Along the first meridian, where the pump polarization evolves from RCP through xx-polarized light to LCP, both RCP and LCP components of the TH signal increase monotonically, with the RCP component consistently dominating (Figure 4e). Notably, an exceptionally high TH DCP of S3(3ω)=0.8S_{3}^{(3\omega)}=0.8 is achieved under xx-polarized excitation, exceeding the value reported in Figure 4d. We attribute this enhancement to the fact that the LP pump used in Figure 4d was oriented at a 15° angle relative to the xx-axis. Along the second meridian, corresponding to a polarization evolution from RCP through yy-polarized light to LCP, the TH intensity and DCP exhibit a slightly different trend (Figure 4f), which may be associated with accidental symmetry breaking due to the fabricated nanopattern of the sample or excitation beam asymmetry.

To further verify that the observed response arises from conventional perturbative third-order nonlinearity, we perform power-dependent measurements using a narrowband pump pulse centered at 1435 nm, within the resonant band (see Supplementary Fig. S8). Under LCP excitation, the TH intensity follows the expected power-law dependence on the pump intensity, I(3ω)∝(I(ω))nI^{(3\omega)}\propto\left(I^{(\omega)}\right)^n. The extracted exponent n=2.85n=2.85 is in reasonable agreement with the theoretical value of 3. Although anomalous power-law behaviour has been recently reported in nonlinear metasurfaces[63], no pronounced deviations are observed in our system.

Finally, we demonstrate that even a spatially depolarized coherent beam can be used to excite the resonance and produce a nonlinear chiral signal. A linearly polarized laser beam passes through a liquid crystal depolarizer Thorlabs DPP25-C, that imprints a rapidly varying spatial distribution of polarization onto the cross-section of the beam, which is later focused on the metasurface using a lens (see schematics in Figure 1d). The polarization of the output beam is rotated by 4° per 25 μ\mum-wide strip, thus covering all possible linear polarizations multiple times across the 5 mm-wide beam cross-section. While the electric field of this beam retains its spatial coherence, the rapid spatial variation of the polarization allows one to use it as an effectively depolarized excitation source.

When the light pulse is centered at 1435 nm, the output nonlinear signal is dominated by its RCP component, featuring TH DCP of S3(3ω)=0.79S_{3}^{(3\omega)}=0.79 (Figure 4g). This DCP is consistently observed across the whole nonlinear response linewidth. As we scan the pump wavelength in the vicinity of the resonance, the integrated TH signal remains strongly RCP, exhibiting S3(3ω)∈[0.57,0.79]S_{3}^{(3\omega)}\in[0.57,0.79] at all wavelengths for which the TH intensity exceeds 25% of the maximum (Figure 4h), confirming robustness of the proposed symmetry-based mechanism for the nonlinear chirality transfer.

The absence of a net linear-polarization bias in the spatially integrated beam can be easily verified by measuring the beam power after it passes through a linear polarizer. As we rotate the depolarizer, the transmitted intensity exhibits variations of less than 1% (Figure 4i). However, rotation of the depolarizer may noticeably affect the TH DCP of the TH signal, generated by the metasurface excited at the chiral resonance (Figure 4j). While the theoretical model of TH generation under depolarized beam excitation, described in Supplementary Sections 4 and 5, only predicts reduction of S3(3ω)S_{3}^{(3\omega)} with increased aperture of the TH collection objective with no dependence on depolarizer rotation, we notice that nonlinear processes are highly sensitive to even small variations of the local fields. Slight asymmetry of the fabricated metasurface lattice, asymmetry of the excitation beam, and opposite transverse phase gradients introduced by the depolarizer (Supplementary Section 5) can lead to significant corrections to the polarization of the generated TH signal. Nevertheless, despite the complex spatially varying polarization excitation, the TH DCP remains above 0.33 for all rotation angles and even reaches 0.8, unambiguously confirming the dominance of the RCP TH component.

Benchmarked against the existing literature in Figure 1c, the simultaneous realization of high TH DCP, near-unity nonlinear CD, and a high effective Q-factor demonstrates the effectiveness of complementary symmetry breaking and symmetry preservation as a design principle for controlling nonlinear optical responses, particularly for achieving strong chirality.

Conclusion

We have experimentally demonstrated a symmetry-based mechanism that enables chirality selection and polarization purification in nonlinear all-dielectric metasurfaces. The central element of this mechanism is a degenerate pair of high-Q resonances with maximal chirality, which selectively amplifies one circular component of the pump and, enforced by rotational symmetry, converts it into a nonlinear signal of opposite handedness. This process realizes nonlinear chirality transfer, whereby a chiral resonant response at the pump frequency deterministically produces a circularly polarized harmonic output. Although our experimental demonstration focuses on third-harmonic generation, the underlying principle is universal: our earlier theoretical work[49] established its applicability to both second- and third-harmonic processes, with natural extensions to higher-order nonlinear interactions.

From an experimental perspective, our metasurface integrates several advances that have not been achieved simultaneously in prior studies. In the linear regime, we demonstrate a maximally chiral resonance in a rotationally symmetric dielectric structure enabled by the mechanism of quasi-guided modes. Previous experimental realizations of chiral quasi-BICs relied on architectures lacking rotational symmetry and were therefore incompatible with nonlinear chirality transfer. In contrast, our approach provides a practical route to realizing chiral high-Q modes in a single-layer, flat, CMOS-compatible platform, without multilayer stacking, multi-height patterning, or substrate engineering.

In the nonlinear regime, we report a near-unity nonlinear circular dichroism of −0.98 together with a degree of circular polarization of the harmonic signal reaching 0.83 under circularly polarized excitation and 0.8 under linearly polarized excitation. These values are among the highest reported for dielectric nonlinear metasurfaces and have not previously been achieved jointly within a single high-Q platform. Importantly, nonlinear circular dichroism alone, as commonly reported for conventional chiral structures, merely reflects intensity asymmetry and provides no information about the polarization state of the generated light. By simultaneously achieving near-unit nonlinear circular dichroism and a high degree of circular polarization, we demonstrate deterministic control over the functional polarization state of the nonlinear output, a prerequisite for applications requiring a deterministic output helicity. Notably, the nonlinear harmonic preserves its handedness even under spatially depolarized coherent light excitation.

Our simulations further reveal that in the ideal case, pump states spanning approximately three-quarters of the Poincaré sphere generate a stable, right-handed third-harmonic output, while the remaining quadrant yields a strongly suppressed response. This behavior is consistent with symmetry selection rules for rotationally symmetric nonlinear processes, but it goes substantially beyond them: the presence of chirality stabilizes the nonlinear polarization output across a broad range of input polarization states. This robustness highlights the potential of chiral high-Q modes as nonlinear chiral emitters, capable of enforcing the handedness of the generated harmonics independently of the pump polarization.

In contrast to a recent study[48] demonstrating control over the degree of circular polarization of the nonlinear signal in achiral metasurfaces, our mechanism relies on intrinsic structural symmetry rather than fine-tuned modal intersections, suggesting broad applicability and robustness. Introduction of an all-optically controlled degree of freedom, for example, strongly asymmetric excitation[64] or intensity-induced modulation[65], may be used to modify the nonlinear selection rules, enabling nonlinear logic functionalities in ultrathin nonlinear photonic metadevices.

In summary, our work demonstrates how symmetry of resonant metasurfaces can be systematically leveraged to control not only the intensity but also the functional polarization of nonlinear optical signals. By combining chirality with rotational symmetry, we establish a general design paradigm for symmetry-controlled nonlinear chiral devices. This approach opens new avenues toward compact sources of structured nonlinear light, ultrathin polarization logic, spin–orbit–engineered nonlinear photonics and quantum nonlinear metasurfaces with chirality-controlled entanglement.

Methods

Scattering matrix bandstructure calculations: The simulations were performed using the rigorous coupled-wave analysis (RCWA) open-source package Inkstone[66]. The unit cell was defined using the two lattice vectors and cylindrical pillars with circular base faces. We defined the refractive index of the silicon as 3 and the silica substrate refractive index as 1.45, the upper half-space was air with a refractive index 1. The metasurface parameters are period p=955p = 955 nm, thickness H=320H = 320 nm, larger pillar radius R=240R = 240 nm, and a smaller pillar radius Rc=150R_{\mathrm{c}} = 150 nm. The scattering matrix for the open radiative channels was calculated for various Bloch vector values and frequencies; its norm on a logarithmic scale is presented in Figure 2b,Figure 2e to visualise the band structure below and above the light cone. RCWA, being a computational algorithm that relies on the Fourier transformation of the material properties and fields, is a fast and accurate tool for modelling periodic metasurfaces with simple shapes, especially in the vicinity of Rayleigh anomalies (openings of diffraction channels).

COMSOL eigenmode simulations: Resonant modes of the metasurface were computed using the COMSOL eigenmode solver. Periodic boundary conditions along the lateral xx- and yy-directions and ports on the upper and lower boundaries were used to define the simulation domain. The metasurface parameters were the same as for the bandstructure calculations. The chirality of a mode with electric field E(r)\mathbf{E}(\mathbf{r}) was evaluated based on the far-field polarization of the mode on the air side:

Erad=1Su.b.∫Su.b.E(r) dS,(7)\mathbf{E}_{\mathrm{rad}} = \frac{1}{S_{\mathrm{u.b.}}} \int_{S_{\mathrm{u.b.}}} \mathbf{E}(\mathbf{r})\,\mathrm{d}S, \tag*{(7)}

where Su.b.S_{\mathrm{u.b.}} is the upper boundary of the metasurface. Accordingly, the DCP, or the normalized third Stokes parameter of the radiation, used as a measure of a mode’s chirality, was evaluated as S3=2Im⁡(Erad,xErad,y∗)/(∣Erad,x∣2+∣Erad,y∣2)S_3 = 2\operatorname{Im}(E_{\mathrm{rad},x}E_{\mathrm{rad},y}^{*})/(|E_{\mathrm{rad},x}|^2 + |E_{\mathrm{rad},y}|^2).

Temporal coupled-mode theory for chiral modes of E representation of C4C_4 group: Consider a degenerate pair of modes at the Γ\Gamma-point, with electric fields satisfying Eq. (1). Within the temporal coupled-mode theory[67], the interaction of such a pair of modes with the radiation continuum at normal incidence is described by equation

dadt=[iω0−γ]a+K^sin,(8)\frac{\mathrm{d}\mathbf{a}}{\mathrm{d}t} = [\mathrm{i}\omega_0-\gamma]\mathbf{a}+\hat{\mathbf{K}}\mathbf{s}^{\mathrm{in}}, \tag*{(8)}

where a=(a1,a2)T\mathbf{a}=(a_1,a_2)^{\mathrm{T}} is the vector of modal amplitudes, ω0+iγ\omega_0+\mathrm{i}\gamma is the complex resonant frequency of the modes, K^\hat{\mathbf{K}} is the matrix of resonant coupling constants that defines coupling to the amplitudes of incoming waves sin=(s1,xin,s1,yin,s2,xin,s2,yin)T\mathbf{s}^{\mathrm{in}}=(s_{1,x}^{\mathrm{in}},s_{1,y}^{\mathrm{in}},s_{2,x}^{\mathrm{in}},s_{2,y}^{\mathrm{in}})^{\mathrm{T}}, with subscripts 1,21,2 denoting the upper and lower half-spaces and subscripts xx and yy denoting the Cartesian components of wave polarization. Due to C4C_4 symmetry and transformation properties of the modes Eq. (1), the coupling constants of the two modes are related through 90-degree rotation operation, and take the form

K^=(K1K2)=(K1,xK1,yK2,xK2,y−K1,yK1,x−K2,yK2,x),(9)\hat{\mathbf{K}}=\begin{pmatrix}\mathbf{K}_1\\ \mathbf{K}_2\end{pmatrix}=\begin{pmatrix}K_{1,x} & K_{1,y} & K_{2,x} & K_{2,y}\\ -K_{1,y} & K_{1,x} & -K_{2,y} & K_{2,x}\end{pmatrix}, \tag*{(9)}

where K1,2\mathbf{K}_{1,2} are the vectors of resonant coupling. Now, assuming mode 1 is tuned to selectively interact with LCP light incident from the top, i.e., it is fully decoupled from RCP excitation sin∝(1,i,0,0)T\mathbf{s}^{\mathrm{in}}\propto(1,\mathrm{i},0,0)^{\mathrm{T}}, we obtain K1,y=iK1,xK_{1,y}=\mathrm{i}K_{1,x}. Under such circumstances, any excitation from the top sin=(s1,xin,s1,yin,0,0)T\mathbf{s}^{\mathrm{in}}=(s_{1,x}^{\mathrm{in}},s_{1,y}^{\mathrm{in}},0,0)^{\mathrm{T}} at frequency ω\omega results in the stationary solution a(t)=aeiωt\mathbf{a}(t)=\mathbf{a}e^{\mathrm{i}\omega t}

a=K^sin[i(ω−ω0)+γ]=2K1,xs1,−in[i(ω−ω0)+γ](1−i),(10)\mathbf{a}=\frac{\hat{\mathbf{K}}\mathbf{s}^{\mathrm{in}}}{[\mathrm{i}(\omega-\omega_0)+\gamma]}=\frac{\sqrt{2}K_{1,x}s_{1,-}^{\mathrm{in}}}{[\mathrm{i}(\omega-\omega_0)+\gamma]}\begin{pmatrix}1\\-\mathrm{i}\end{pmatrix}, \tag*{(10)}

where s1,−in=1/2(s1,xin+is1,yin)s_{1,-}^{\mathrm{in}}=1/\sqrt{2}(s_{1,x}^{\mathrm{in}}+\mathrm{i}s_{1,y}^{\mathrm{in}}) is the amplitude of the LCP component of the incident wave coming from top. We conclude that regardless of the incident light polarization, both modes are excited with the same absolute value of the amplitude and a constant phase offset a1=ia2a_1=\mathrm{i}a_2; pure RCP excitation does not resonantly excite the doublet. Hence, omitting weak nonresonant terms, the induced field within the metasurface Eω(r)≈a1E1(r)+a2E2(r)\mathbf{E}^{\omega}(\mathbf{r})\approx a_1\mathbf{E}_1(\mathbf{r})+a_2\mathbf{E}_2(\mathbf{r}) obeys the chiral transformation rule Eq. (2).

Semi-analytical perturbation model: We consider the electric-field distribution E(r)=E1(r)\mathbf{E}(\mathbf{r}) = \mathbf{E}_1(\mathbf{r}) of one of the degenerate resonant modes of the unperturbed structure. The other mode is related to the first one through Eq. (1). When a boundary-shift perturbation is introduced, the perturbed resonant field E~(r)\widetilde{\mathbf{E}}(\mathbf{r}) remains unchanged in regions where the permittivity is preserved,

E~(r)=E(r) for r∈Ures∪Ubg.\widetilde{\mathbf{E}}(\mathbf{r}) = \mathbf{E}(\mathbf{r}) \text{ for } \mathbf{r} \in U_{\mathrm{res}} \cup U_{\mathrm{bg}}.

In regions where the permittivity is modified, we employ the following approximation:

E~∥(r)=E∥(r)∣r∈δUres∪δUbg,E~⊥(r)=E⊥(r)εSi∣r∈δUresandE~⊥(r)=εSiE⊥(r)∣r∈δUbg.(11)\widetilde{\mathbf{E}}_{\parallel}(\mathbf{r}) = \left.\mathbf{E}_{\parallel}(\mathbf{r})\right|_{\mathbf{r}\in\delta U_{\mathrm{res}}\cup\delta U_{\mathrm{bg}}}, \qquad \widetilde{\mathbf{E}}_{\perp}(\mathbf{r}) = \left.\frac{\mathbf{E}_{\perp}(\mathbf{r})}{\varepsilon_{\mathrm{Si}}}\right|_{\mathbf{r}\in\delta U_{\mathrm{res}}} \qquad\text{and}\qquad \widetilde{\mathbf{E}}_{\perp}(\mathbf{r}) = \left.\varepsilon_{\mathrm{Si}}\mathbf{E}_{\perp}(\mathbf{r})\right|_{\mathbf{r}\in\delta U_{\mathrm{bg}}}. \tag*{(11)}

where ⊥\perp and ∥\parallel denote the normal and tangential components with respect to the local surface of an elliptical cylinder passing through the point r\mathbf{r}. These surfaces form a continuous morphing family connecting the circular and elliptical pillars, parameterized by ΔR′∈[0,ΔR]\Delta R^{\prime}\in[0,\Delta R] and defined by the rotation angle θ\theta and half-lengths R±ΔR′R\pm\Delta R^{\prime}. Unlike the unperturbed field E(r)\mathbf{E}(\mathbf{r}), the perturbed field E~(r)\widetilde{\mathbf{E}}(\mathbf{r}) is constructed to satisfy the relevant electric-field interface continuity conditions for the modified structure.

Using the reciprocity principle[68], we evaluate the coupling coefficients K1,αK_{1,\alpha} (α=x,y\alpha=x,y) of the perturbed resonant mode as

K1,α∝∫(ε~(r)−εbg(r))Eαbg(r)E~(r) d3r.(12)K_{1,\alpha}\propto\int\left(\widetilde{\varepsilon}(\mathbf{r})-\varepsilon_{\mathrm{bg}}(\mathbf{r})\right)\mathbf{E}^{\mathrm{bg}}_{\alpha}(\mathbf{r})\widetilde{\mathbf{E}}(\mathbf{r})\,\mathrm{d}^{3}\mathbf{r}. \tag*{(12)}

where εbg(r)\varepsilon_{\mathrm{bg}}(\mathbf{r}) is the background permittivity in the absence of the resonator, and Eαbg(r)\mathbf{E}^{\mathrm{bg}}_{\alpha}(\mathbf{r}) is the background electric field generated by a plane wave with polarization α\alpha incident in the reciprocal configuration. In essence, the original radiation problem is recast as a reciprocal scattering problem.

To account for the substrate with permittivity εSiO2=nSiO22=1.452\varepsilon_{\mathrm{SiO_2}}=n_{\mathrm{SiO_2}}^{2}=1.45^{2}, we set εbg(z≤0)=εSiO2\varepsilon_{\mathrm{bg}}(z\leq0)=\varepsilon_{\mathrm{SiO_2}} and εbg(z>0)=1\varepsilon_{\mathrm{bg}}(z>0)=1. The corresponding background field in the reciprocal problem is

Eαbg(r)=e^α(exp⁡(ik0z)+1−nSiO21+nSiO2exp⁡(−ik0z)).\mathbf{E}^{\mathrm{bg}}_{\alpha}(\mathbf{r})=\hat{\mathbf{e}}_{\alpha}\left(\exp(\mathrm{i}k_{0}z)+\frac{1-n_{\mathrm{SiO_2}}}{1+n_{\mathrm{SiO_2}}}\exp(-\mathrm{i}k_{0}z)\right).

where e^α\hat{\mathbf{e}}_{\alpha} is the polarization unit vector.

Substituting the perturbed field expansion from Eq. (11) into Eq. (12), we obtain

K1,α∝∫UresEαbg(r)E(r) d3r+∫δUresEαbg(r)(E∥(r)+ε(r)ε~(r)E⊥(r)) d3r.(13)K_{1,\alpha}\propto\int_{U_{\mathrm{res}}}\mathbf{E}^{\mathrm{bg}}_{\alpha}(\mathbf{r})\mathbf{E}(\mathbf{r})\,\mathrm{d}^{3}\mathbf{r}+\int_{\delta U_{\mathrm{res}}}\mathbf{E}^{\mathrm{bg}}_{\alpha}(\mathbf{r})\left(\mathbf{E}_{\parallel}(\mathbf{r})+\frac{\varepsilon(\mathbf{r})}{\widetilde{\varepsilon}(\mathbf{r})}\mathbf{E}_{\perp}(\mathbf{r})\right)\,\mathrm{d}^{3}\mathbf{r}. \tag*{(13)}

While the resonant fields E(r)\mathbf{E}(\mathbf{r}) and E~(r)\widetilde{\mathbf{E}}(\mathbf{r}) can be properly normalized to yield exact equalities[60, 69], this is of minor importance for the evaluation of the far-field polarization state of the resonant mode. Finally, chirality of the mode in this interface-perturbative approach is evaluated as S3=2Im⁡(K1,xK1,y∗)/(∣K1,x∣2+∣K1,y∣2)S_{3}=2\operatorname{Im}(K_{1,x}K_{1,y}^{*})/(|K_{1,x}|^{2}+|K_{1,y}|^{2}).

Numerical modeling: Linear vs. nonlinear chiral response: Plane wave scattering in the linear regime was modeled in the “Electromagnetic Waves, Frequency Domain” module of COMSOL. The boundary conditions and unit cell design were adopted from the eigenmode simulation, with a small imaginary part of the Si refractive index of 0.01 introduced to mimic the material losses. To ensure simulation accuracy in the following nonlinear simulation, the spatial mesh in the Si, SiO2_2, and air domains was defined explicitly with the largest element size not exceeding 0.17λ3n\frac{0.17\lambda}{3n}, where λ=1400\lambda= 1400 nm is the minimum pump wavelength and nn is the refractive index of a particular material. Transmission coefficients were extracted using the port functionality.

The nonlinear part of the simulation was done in the second consecutive simulation, where the calculated electric fields in the linear scattering simulation were used as a source of nonlinear polarization. The material properties were kept the same in both the linear and idealized nonlinear simulations. The ports at the upper and lower boundaries were replaced with second-order scattering conditions; additionally, the frequency of the simulation was explicitly defined to be 3 times higher than the frequency of the first simulation. No incoming waves were used in this simulation. The far-field TH radiation in the main diffraction channel was extracted at the lower boundary of the simulation domain according to Eq. (7).

Fabrication of the chiral metasurface: First, a 320-nm-thick α-Si film was deposited on a SiO2_2 substrate. Hydrogen silsesquioxane (HSQ, Dow Corning XR-1541-006) resist was spin-coated at 5000 rpm to obtain a ∼150 nm layer, followed by spin coating of an ∼80 nm AR-PC 5090 conductive layer at 2000 rpm. The sample was patterned by electron-beam lithography (EBL, Raith Eline Plus, 30 keV, 450 pA). The conductive layer was rinsed off with deionized water for 1 min, and the HSQ pattern was developed in 25 wt.% TMAH for 3 min, followed by a deionized water rinse and isopropanol drying. The α-Si layer was etched using ICP-RIE (Oxford Plasmalab System 100) with Cl2_2 gas (22 sccm), ICP power 300 W, RF power 100 W, chamber pressure 5 mTorr, and chiller temperature 10 °C.

Linear optical characterization: The linear transmission of the metasurface was measured in a home-built setup (Supplementary Fig. S9) using a broadband incoherent light source (Thorlabs OSL2, 1300–1600 nm). The incident beam was converted to circular polarization using a linear polarizer and a quarter-wave plate. To address the angle sensitivity of the quasi-guided modes, a long-focal-length NIR lens (f = 50 mm) generated a low-NA excitation beam near normal incidence. Transmitted light was collected with a 10× objective (NA = 0.26) and analyzed using a spectrometer (Kymera 328i) coupled to a cooled InGaAs CCD. Angle-resolved transmission spectra were measured using a commercial microscope system, where the transmitted light was dispersed by a diffraction grating and recorded by a NIR CMOS camera.

Nonlinear optical characterization (THG): For third-harmonic generation (THG) measurements, the incoherent light source was replaced with a home-built wavelength-tunable optical parametric amplifier (OPA) used in Ref. 70 pumped by a pulsed laser (Amplitude Yuja, center wavelength of 1030 nm, repetition rate of 100 kHz, and pulse duration of 400 fs). The output wavelength of the OPA was tuned from 1400 to 1470 nm by selecting periodically poled lithium niobate (PPLN) crystals with different poling periods and adjusting the crystal temperature. The pump polarization was controlled using a linear polarizer with a quarter-wave plate to tune the S3S_3 of the excitation beam, or a half-wave plate for achieving arbitrary linear polarization. THG emission was collected using the same 10×10 \times objective and analyzed with a spectrometer (Kymera 328i) coupled to a Si CCD. A short-pass filter blocked the pump light, and RCP/LCP components of the THG signal were resolved using a quarter-wave plate followed by a linear polarizer (Supplementary Fig. S10).

AI and LLM Usage: During the preparation of this manuscript, the authors used OpenAI's ChatGPT-5 and ChatGPT-6 for formatting, text editing, and proofreading to improve readability and grammatical accuracy.

Authors’ Contributions

D.G., C.W.Q., and L.W. conceived the project idea. Q.W., J.K.W.Y., C.W.Q., and L.W. supervised the project. D.G., S.T., C.W.Q., and L.W. developed the theoretical background. D.G. performed numerical simulations. C.F.P., H.T.W., B.W., S.Z., and H.W. fabricated the samples. C.F.P. prepared the SEM images. W.J. and X.M. designed the optical experiments and built the linear and TH characterization setups. W.J., X.M., W.C., Z.X., and C.F.P. performed the experiments. W.J., D.G., X.M., W.C., C.F.P., and Z.X. analysed the data. D.G., W.J., C.W.Q., and L.W. wrote the manuscript with the contribution of all authors.

Competing interests

The authors declare no competing interests.

Data availability

All data supporting the findings of this study are available within the Article and its Supplementary Information. Additional data are available from the corresponding authors upon reasonable request.

Code availability

No custom code is required to reproduce the findings of this study. The numerical methods and software used in the study are described in the Methods section.

Acknowledgements

We thank Dr. Jianfeng Chen (NUS), Dr. Jieyuan Cui (NTU), and Ms. Hanyu Liu (NTU) for helpful discussions. This work was supported by the National Research Foundation, Singapore (NRF-CRP26-2021-0004, NRF-CRP31-0007, NRF2023-ITC004-001, NRF-CRP29-2022-0003, and NRF-MSG-2023-0002), the Ministry of Education, Singapore (MOE-T2EP50223-0001, MOE-MOET32024-0005, MOET32024-0001), the Agency for Science, Technology and Research (A*STAR) (MTC IRG M24N7c0083, Programmatic Funds R23I0IR041, M23M2b0056), the Singapore University of Technology and Design (SUTD) under the Kickstarter Initiative (SKI 2021-04-12), the Advanced Research and Technology Innovation Centre (ARTIC), the National University of Singapore under Grant (project number: AFP-RP4). D.G. and C.P. acknowledge the support of the Ph.D. Research Scholarship Scheme.

References

  1. [1]Solomon, M. L. et al. Nanophotonic platforms for chiral sensing and separation. Accounts of Chemical Research 53, 588-598 (2020).DOI
  2. [2]Liu, Y. et al. Controlling valley-specific light emission from monolayer MoS₂ with achiral dielectric metasurfaces. Nano Letters 23, 6124-6131 (2023).DOI
  3. [3]Wang, B. et al. Generating optical vortex beams by momentum-space polarization vortices centred at bound states in the continuum. Nature Photonics 14, 623-628 (2020).DOI
  4. [4]Menshikov, E. et al. Light structuring via nonlinear total angular momentum addition with flat optics. Light: Science & Applications 14, 381 (2025).DOI
  5. [5]Hirohata, A. et al. Review on spintronics: Principles and device applications. Journal of Magnetism and Magnetic Materials 509, 166711 (2020).DOI
  6. [6]Lodahl, P. et al. Chiral quantum optics. Nature 541, 473-480 (2017).DOI
  7. [7]Gorkunov, M. V., Antonov, A. A. & Kivshar, Y. S. Metasurfaces with Maximum Chirality Empowered by Bound States in the Continuum. Physical Review Letters 125, 093903 (2020). https://doi.org/10.1103/PhysRevLett.125.093903
  8. [8]Chen, Y. et al. Observation of intrinsic chiral bound states in the continuum. Nature 613, 474-478 (2023).DOI
  9. [9]Chen, Y. et al. Compact spin-valley-locked perovskite emission. Nature Materials 22, 1065-1070 (2023). https://doi.org/10.1038/s41563-023-01531-2
  10. [10]Gromyko, D. et al. Unidirectional chiral emission via twisted bi-layer metasurfaces. Nature Communications 15, 9804 (2024).arxiv.org/abs/2406.16003
  11. [11]Hu, H. et al. Robust chirality via emerging accidental BICs with net zero topological charge. eLight 6, 12 (2026).DOI
  12. [12]Wang, Y. et al. Resonant helical dichroism in twisted dielectric metastructures. ACS Nano 19, 31894-31900 (2025).DOI
  13. [13]Wang, M. et al. Chiral orbital lasing in a twisted bilayer metasurface. Nature Communications 17, 2369 (2026).DOI
  14. [14]Voronin, K., Taradin, A. S., Gorkunov, M. V. & Baranov, D. G. Single-handedness chiral optical cavities. ACS Photonics 9, 2652-2659 (2022).arxiv.org/abs/2104.14230
  15. [15]Bao, Y. et al. On-demand spin-state manipulation of single-photon emission from quantum dot integrated with metasurface. Science Advances 6, eaba8761 (2020).DOI
  16. [16]Rauter, P. et al. Electrically pumped semiconductor laser with monolithic control of circular polarization. Proceedings of the National Academy of Sciences 111, E5623-E5632 (2014).DOI
  17. [17]Demenev, A. et al. Circularly polarized lasing in chiral modulated semiconductor microcavity with GaAs quantum wells. Applied Physics Letters 109 (2016).DOI
  18. [18]Maksimov, A. et al. Circularly polarized laser emission from an electrically pumped chiral microcavity. Physical Review Applied 17, L021001 (2022).DOI
  19. [19]Zhang, X., Liu, Y., Han, J., Kivshar, Y. & Song, Q. Chiral emission from resonant metasurfaces. Science 377, 1215-1218 (2022).DOI
  20. [20]Deng, H. et al. Chiral lasing enabled by strong coupling. Science Advances 11, eads9562 (2025).DOI
  21. [21]Dyakov, S., Gippius, N., Fradkin, I. & Tikhodeev, S. Vertical routing of spinning-dipole radiation from a chiral metasurface. Physical Review Applied 14, 024090 (2020).DOI
  22. [22]Krasnok, A., Tymchenko, M. & Alù, A. Nonlinear metasurfaces: a paradigm shift in nonlinear optics. Materials Today 21, 8-21 (2018).arxiv.org/abs/1706.07563
  23. [23]Vabishchevich, P. & Kivshar, Y. Nonlinear photonics with metasurfaces. Photon. Res. 11, B50-B64 (2023). https://doi.org/10.1364/PRJ.474387
  24. [24]Cotrufo, M., Carletti, L., Overvig, A. & Alù, A. Nonlinear nonlocal metasurfaces. eLight 6, 5 (2026).DOI
  25. [25]Ma, J. et al. Quantum imaging using spatially entangled photon pairs from a nonlinear metasurface. eLight 5, 2 (2025).DOI
  26. [26]Makarov, S. V. et al. Efficient second-harmonic generation in nanocrystalline silicon nanoparticles. Nano Letters 17, 3047-3053 (2017).DOI
  27. [27]Xu, X. et al. Towards compact phase-matched and waveguided nonlinear optics in atomically layered semiconductors. Nature Photonics 16, 698-706 (2022).DOI
  28. [28]Zograf, G. et al. Ultrathin 3R-MoS₂ metasurfaces with atomically precise edges for efficient nonlinear nanophotonics. Communications Physics 8, 271 (2025).arxiv.org/abs/2410.20960
  29. [29]Liu, Z. et al. High-Q quasibound states in the continuum for nonlinear metasurfaces. Physical Review Letters 123, 253901 (2019).DOI
  30. [30]Smirnova, D. et al. Third-harmonic generation in photonic topological metasurfaces. Physical Review Letters 123, 103901 (2019).DOI
  31. [31]Abdelraouf, O. A. et al. Multistate tuning of third harmonic generation in Fano-resonant hybrid dielectric metasurfaces. Advanced Functional Materials 31, 2104627 (2021).arxiv.org/abs/2105.04233
  32. [32]Liu, H. et al. Enhanced high-harmonic generation from an all-dielectric metasurface. Nature Physics 14, 1006-1010 (2018).DOI
  33. [33]Zograf, G. et al. High-harmonic generation from resonant dielectric metasurfaces empowered by bound states in the continuum. ACS Photonics 9, 567-574 (2022).DOI
  34. [34]Chen, S. et al. Giant nonlinear optical activity of achiral origin in planar metasurfaces with quadratic and cubic nonlinearities. Advanced Materials 28, 2992-2999 (2016).DOI
  35. [35]Tang, Y. et al. Nano-Kirigami metasurface with giant nonlinear optical circular dichroism. Laser & Photonics Reviews 14, 2000085 (2020).DOI
  36. [36]Kim, D. et al. Giant nonlinear circular dichroism from intersubband polaritonic metasurfaces. Nano Letters 20, 8032-8039 (2020). https://doi.org/10.1021/acs.nanolett.0c02978
  37. [37]Konishi, K. et al. Polarization-controlled circular second-harmonic generation from metal hole arrays with threefold rotational symmetry. Physical Review Letters 112, 135502 (2014).pubmed.ncbi.nlm.nih.gov/24745436
  38. [38]Chen, S. et al. Symmetry-selective third-harmonic generation from plasmonic metacrystals. Physical Review Letters 113, 033901 (2014).DOI
  39. [39]Li, G., Zhang, S. & Zentgraf, T. Nonlinear photonic metasurfaces. Nature Reviews Materials 2, 1-14 (2017).
  40. [40]Liu, B. et al. Nonlinear wavefront control by geometric-phase dielectric metasurfaces: influence of mode field and rotational symmetry. Advanced Optical Materials 8, 1902050 (2020).DOI
  41. [41]Konishi, K. et al. Circularly polarized vacuum ultraviolet coherent light generation using a square lattice photonic crystal nanomembrane. Optica 7, 855-863 (2020).DOI
  42. [42]Shi, T. et al. Planar chiral metasurfaces with maximal and tunable chiroptical response driven by bound states in the continuum. Nature Communications 13, 4111 (2022).DOI
  43. [43]Koshelev, K., Tonkaev, P. & Kivshar, Y. Nonlinear chiral metaphotonics: a perspective. Advanced Photonics 5, 064001-064001 (2023).DOI
  44. [44]Koshelev, K. et al. Resonant chiral effects in nonlinear dielectric metasurfaces. ACS Photonics 10, 298-306 (2023).DOI
  45. [45]Toftul, I. et al. Chiral dichroism in resonant metasurfaces with monoclinic lattices. Physical Review Letters 133, 216901 (2024).DOI
  46. [46]Tonkaev, P. et al. Nonlinear chiral metasurfaces based on structured van der Waals materials. Nano Letters 24, 10577-10582 (2024).DOI
  47. [47]Toftul, I. et al. Monoclinic nonlinear metasurfaces for resonant engineering of polarization states. Nanophotonics 14, 4145-4151 (2025).arxiv.org/abs/2501.08494
  48. [48]Lai, F. et al. Nonlinear chiral light generation from resonant metasurfaces. Nature Communications 16, 10686 (2025).arxiv.org/abs/2509.06683
  49. [49]Gromyko, D., Loh, J. S., Feng, J., Qiu, C.-W. & Wu, L. Enabling all-to-circular polarization up-conversion by nonlinear chiral metasurfaces with rotational symmetry. Physical Review Letters 134, 023804 (2025).DOI
  50. [50]Overvig, A., Yu, N. & Alù, A. Chiral quasi-bound states in the continuum. Physical Review Letters 126, 073001 (2021).DOI
  51. [51]Sha, X. et al. Chirality tuning and reversing with resonant phase-change metasurfaces. Science Advances 10, eand9017 (2024).arxiv.org/abs/2401.01490
  52. [52]Kühner, L. et al. Unlocking the out-of-plane dimension for photonic bound states in the continuum to achieve maximum optical chirality. Light: Science & Applications 12, 250 (2023).DOI
  53. [53]Gorkunov, M. V., Antonov, A. A., Tuz, V. R., Kuprianov, A. S. & Kivshar, Y. S. Bound states in the continuum underpin near-lossless maximum chirality in dielectric metasurfaces. Advanced Optical Materials 9, 2100797 (2021).DOI
  54. [54]Overvig, A. C., Malek, S. C., Carter, M. J., Shrestha, S. & Yu, N. Selection rules for quasibound states in the continuum. Physical Review B 102, 053434 (2020).DOI
  55. [55]Sakoda, K. Optical properties of photonic crystals. Vol. 2 (Springer, 2005).
  56. [56]Tikhodeev, S. G., Yablonskii, A., Muljarov, E., Gippius, N. A. & Ishihara, T. Quasiguided modes and optical properties of photonic crystal slabs. Physical Review B 66, 045102 (2002).DOI
  57. [57]Huang, L. et al. Ultrahigh-Q guided mode resonances in an all-dielectric metasurface. Nature Communications 14, 3433 (2023).DOI
  58. [58]Gorkunov, M. V., Antonov, A. A., Mamonova, A. V., Muljarov, E. A. & Kivshar, Y. Substrate-Induced Maximum Optical Chirality of Planar Dielectric Structures. Advanced Optical Materials 13, 2402133 (2025).DOI
  59. [59]Liu, T. et al. Polarization-independent enhancement of third-harmonic generation empowered by doubly degenerate quasi-bound states in the continuum. Nano Letters 25, 3646-3652 (2025). https://doi.org/10.1021/acs.nanolett.5c00146
  60. [60]Sztranyovszky, Z., Langbein, W. & Muljarov, E. A. First-order perturbation theory of eigenmodes for systems with interfaces. Physical Review Research 5, 013209 (2023).DOI
  61. [61]Yan, W., Lalanne, P. & Qiu, M. Shape deformation of nanoresonator: a quasinormal-mode perturbation theory. Physical Review Letters 125, 013901 (2020).DOI
  62. [62]Wang, C., Gromyko, D., Pantyukhina, P., Wu, L. & Koshelev, K. Nonlinearity-induced chirality in resonant metasurfaces. arXiv preprint arXiv:2607.17600 (2026).
  63. [63]Tonkaev, P. & Kivshar, Y. Unconventional Nonlinear Metaphotonics. Laser & Photonics Reviews, e02236 (2025).DOI
  64. [64]Huang, C. et al. Ultrafast control of vortex microlasers. Science 367, 1018-1021 (2020).DOI
  65. [65]Rodrigues, S. P. et al. Intensity-dependent modulation of optically active signals in a chiral metamaterial. Nature Communications 8, 14602 (2017).DOI
  66. [66]Song, A. Y. Inkstone: Efficient electromagnetic solver based on rigorous coupled-wave analysis, <https://github.com/alexysong/inkstone> (2025).
  67. [67]Fan, S., Suh, W. & Joannopoulos, J. D. Temporal coupled-mode theory for the Fano resonance in optical resonators. Journal of the Optical Society of America A 20, 569-572 (2003).pubmed.ncbi.nlm.nih.gov/12630843
  68. [68]Sauvan, C., Hugonin, J.-P., Maksymov, I. S. & Lalanne, P. Theory of the spontaneous optical emission of nanosize photonic and plasmon resonators. Physical Review Letters 110, 237401 (2013).pubmed.ncbi.nlm.nih.gov/25167528
  69. [69]Weiss, T. & Muljarov, E. A. How to calculate the pole expansion of the optical scattering matrix from the resonant states. Physical Review B 98, 085433 (2018). https://doi.org/10.1103/PhysRevB.98.085433

Paper details

vlnc:W_je4pnq9r
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 2

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents