WorksPhysics and Astronomy
Delta-sigma noise shaping for low-resolution quantization in Gaussian-modulated continuous-variable quantum key distribution
Abstract
Low-resolution digital-to-analog conversion can simplify continuous-variable quantum key distribution (CVQKD) transmitters, but coarse quantization increases excess noise and can generate data-correlated spectral replicas. We demonstrate digital delta–sigma modulation (DSM) for low-resolution waveform generation in Gaussian-modulated CVQKD. In a 500-MBaud CVQKD system over 20~km of fiber, 3-bit second-order DSM achieves an estimated asymptotic secret key rate of 46.38~Mbps at an oversampling ratio of 12, whereas uniform quantization yields no positive rate. With 4-bit second-order DSM, the rate reaches 50.11~Mbps, approximately 97% of the 12-bit reference. A noise model combining the DSM noise-transfer function with matched filtering guides the sampling-rate and signal-band design for effective noise suppression. We also identify a phase-conjugate spectral replica arising from third-order intermodulation between the pilot tone and quantum signal, and evaluate its key-rate penalty using a linear-replica security model. At 3-bit resolution and an oversampling ratio of 24, first-order DSM reduces the experimentally estimated leakage-mode strength by approximately four orders of magnitude. Together, our findings establish the security boundaries and operating conditions of DSM, providing design guidance for low-resolution CVQKD transmitters.
Introduction
High-speed continuous-variable quantum key distribution (CVQKD) increasingly relies on digital waveform generation and coherent optical communication components, including high-speed digital-to-analog converters (DACs), IQ modulators, balanced photodetectors, and integrated coherent receivers [1, 2, 3, 4, 5, 6, 7, 8]. Recent silicon photonic implementations further demonstrate the potential for compact transmitters and receivers, including Gaussian-modulated systems with integrated receivers [9, 10]. At a Gaussian-modulated transmitter, the intended electrical waveform must be represented by the finite amplitude levels available from a practical DAC [11]. The difference between the true waveform and the discretized waveform is defined as quantization noise. At high resolution, quantization error is often approximated as additive white noise independent of the original signal [12] and is usually treated as part of the preparation noise in CVQKD. Lower DAC resolution reduces transmitter complexity, power consumption, and implementation cost, especially at high speeds [13].
However, coarse quantization can distort the prepared states and increase excess noise, making transmitter resolution an important implementation constraint [14, 15, 16]. In pilot-assisted systems, sharing the DAC dynamic range between a weak quantum signal and a stronger phase-reference tone can further increase the required resolution [17, 18, 19, 20, 21]. Therefore, it is important to understand and mitigate quantization effects while retaining the practical advantages of low-resolution waveform generation.
Existing security analyses show that a sufficiently fine discrete approximation can reproduce ideal Gaussian modulation in practice [14], while discrete-modulation protocols using a finite constellation offer an alternative route to simpler implementations [22, 23, 24]. In practical CVQKD implementations, researchers usually incorporate quantization error into the noise budget as an equivalent excess-noise contribution [15, 19, 25, 26]. Recent simulations comparing electrical and optical pilot generation have also examined low-resolution DAC distortion and shown that optical pilot generation can relax the DAC-resolution requirement [21]. More recently, researchers have jointly optimized transmitter and receiver filters under finite DAC/ADC resolution and bandwidth constraints, retaining quantization error as an additive variance in the system model [27]. These approaches quantify quantization error but do not explicitly design its statistical features, such as its spectral distribution.
The spectral structure of quantization noise becomes important at medium-to-low resolutions. Without dither, coarse quantization error need not be white or independent of the modulation data and can produce deterministic, data-correlated spectral components [12, 28]. Coarse quantization is a nonlinear amplitude-mapping operation and can generate harmonic and intermodulation products correlated with the original data [29]. If these components transfer to unintended optical modes accessible to an eavesdropper, in-band excess-noise variance alone cannot characterize the resulting side channel [30, 31]. The general security implications of unintended modes that carry correlated modulation and are accessible to an eavesdropper have been studied [25, 30, 31, 32], but they do not cover the low-DAC-resolution scenario. A more relevant work shows that sidelobes from the DAC zero-order hold can form a side channel when excluded from calibration and parameter estimation [33]. But the mechanism differs from the low-resolution quantization replicas considered here in their physical origins and spectral locations. Zero-order-hold images are periodic copies of the sampled spectrum, with locations fixed by the DAC sampling rate. By contrast, we show that the data-correlated modes from coarse DAC quantization may fall inside the first Nyquist zone. This distinction motivates examining both in-band noise and data correlations in quantization-induced spectral replicas.
In this work, we investigate transmitter-side quantization noise shaping to suppress both excess noise and data-correlated side channels caused by insufficient DAC resolution. In particular, we use delta–sigma modulation (DSM) as a simple realization of noise shaping, which uses oversampling and low-order feedback to implement a prescribed noise transfer function (NTF) that suppresses quantization noise in a target band and redistributes it to higher frequencies [34, 35, 36]. DSM and related error-feedback structures have been used for low-resolution waveform generation, mobile fronthaul, and digital predistortion in classical optical links [37, 38, 39, 40, 41]. For CVQKD, the benefit must be evaluated within the effective quantum-signal mode
selected by pulse shaping, detection, and digital filtering [42]. Building on our preliminary results [43], this work incorporates the DSM into the quantum transmitter and evaluates quantization-noise shaping in a complete CVQKD experimental system. We derive an in-band quantization-noise and signal-to-quantization-noise ratio (SQNR) model jointly determined by the NTF, the root-raised-cosine (RRC) pulse-shaping, and matched-filter responses. We further evaluate the effect of low-resolution quantization in a 500-MBaud Gaussian-modulated CVQKD system over 20 km of fiber. Experimental results identify the operating region set by quantizer resolution, oversampling ratio (OSR), and DSM order. At 12-fold oversampling, a 3-bit second-order DSM reduces excess noise from 0.86 SNU (uniform quantization) to 0.028 SNU and restores a positive estimated asymptotic secret key rate of 46.38 Mbps. With 4-bit second-order DSM, the estimated key rate reaches 50.11 Mbps, approximately 97% of the 51.66 Mbps reference obtained from the 12-bit waveform generator. In addition, we find that a first-order DSM reduces the linear correlation between the Gaussian-modulated signal and the quantization-induced replicas by three orders of magnitude relative to the 3-bit uniform quantization. We also confirm that a proper analog or digital filter can further reduce the amplitude of the quantization-induced replicas. These results establish a practical operating region for low-resolution Gaussian-modulated CVQKD while demonstrating suppression of quantization-induced linear correlations outside the signal band.
DSM Principle and Quantization-Noise Model
Here, we consider frequency pilot-tone-assisted Gaussian-modulated CVQKD [44]. Alice generates independent and identically distributed Gaussian variables. After upsampling and RRC pulse shaping, they form the baseband quantum signal [11]. Upconverting to the center frequency and combining it with a pilot of frequency and complex amplitude gives the overall waveform
where is the DAC sampling rate with unit sample-per-second (Sa/s). Let be the symbol rate, and define the OSR as . The I and Q components of the composite waveform are
quantized independently. For a bit depth , the quantization steps are
where and denote the respective full-scale amplitudes. Let denote the uniform quantizer, which maps the waveform to discrete levels.
Figure 1(a) and (b) are the block diagrams of first- and second-order DSMs with cascade-of-integrators-with-feedback (CIFB) structures. The first-order DSM satisfies
Figure 1. Structure of (a) first-order DSM, (b) second-order DSM, and (c) ideal noise transfer function.
and the second-order DSM satisfies
The internal quantization error is defined as and for the first- and second-order DSMs, respectively. Under the linearized additive quantization-error model [35, 36], the signal transfer function (STF) of the th-order DSM is unity, whereas the noise transfer function (NTF) is given by (detailed in the Appendix)
Let denote the quantization error at the DSM output with a power spectral density (PSD) . Let be the PSD of the internal quantization error. The input–output relation of the DSM gives .
Figure 1(c) plots the quantization-error power gain. The dashed 0-dB line represents uniform quantization without noise shaping. For , the NTF magnitude is below unity and decreases as the DSM order increases, providing progressively stronger suppression near zero frequency. Note that all orders have a zero at DC and cross the 0-dB reference at .
Increasing the order therefore strengthens low-frequency suppression without extending the frequency range of quantization noise suppression. For , the NTF magnitude exceeds unity, and higher-order DSM produces stronger amplification of the quantization error. Thus, the benefit of increasing the DSM order depends on the position and signal bandwidth relative to these noise-suppression and amplification regions. For the frequency-shifted signal considered here, the resulting in-band noise power must be evaluated by weighting the shaped error spectrum with the receiver matched-filter response.
Let denote the baseband frequency relative to the quantum-signal center, and let denote the receiver RRC matched-filter response, whose magnitude equals that of the transmitter pulse-shaping filter. For an ideal RRC filter, the response is supported on , where and is the roll-off factor. The filter is peak-normalized such that
Because quantization occurs after transmitter pulse shaping, the resulting error is subsequently weighted by the receiver matched-filter response. The time-averaged quantization-error power at the matched-filter output is therefore
To obtain an analytical SQNR estimate, we adopt a zero-mean white-noise approximation for the internal quantization error
[12]. Using for the total noise power, the two-sided noise PSD is
Substituting (8) into (7) gives
Let denote the quantum signal power at the same matched-filter output. Assuming each quadrature error is uniformly distributed over an equal interval, , yields
Combining (5), (9) and (10) yields
This expression accounts for the combined effects of DSM order, quantizer resolution, signal center frequency, sampling rate, and receiver filtering.
Simulation and Spectral Analysis
Table 1 summarizes the principal simulation and experimental parameters. The SQNR simulations use Gaussian symbols at a symbol rate of 500 MBaud, with a pilot-to-signal power ratio (PSPR) of 10. To calculate the SQNR, the signal waveforms before and after quantization are downconverted to baseband, then the same matched filter is used to extract the components within the QKD band.
| Parameter | Simulation | Experiment |
| Protocol/test waveform | Gaussian modulation; QPSK for spectral-replica diagnostics | Gaussian-modulated LLO-CVQKD |
| Symbol rate | 500 MBaud | 500 MBaud |
| RRC roll-off factor | 0.1 | 0.1 |
| Quantum-signal center frequency | 300 MHz by default; 0.3–2 GHz sweep | 300 MHz |
| Pilot frequency | 700 MHz | 750 MHz |
| Sampling rate/OSR | 1.5–24 GHz / 3–48 | 2–12 GHz / 4–24 |
| Imposed quantizer resolution | 3 and 8 bits; 2, 3, 4, 5 bits used for replica diagnostics | 3–8 bits |
| Fiber and receiver | — | 20-km SSMF; 1.6-GHz balanced detector |
| Detection parameters | — | , SNU |
| Key-rate parameters | — | , |
Table 1. Simulation and experimental parameters.
Both OSR and QKD center frequency critically affect the in-band SQNR. We simulate 3-bit and 8-bit DSMs to verify the impact of high OSR and the QKD center-frequency setting on SQNR, and show the results in Figure 2. Figure 2(a) shows that the in-band SQNR increases with OSR in general, with DSM providing a steeper improvement than uniform quantization. At sufficiently high OSRs, second-order DSM achieves a significantly higher SQNR than first-order DSM. At OSR = 3, however, both DSM schemes perform worse than uniform quantization, and increasing the DSM order further degrades the SQNR. This is because the DSM, regardless of order, suppresses quantization noise only for within the first Nyquist band.
Figure 2. Simulated in-band SQNR and the theoretical prediction based on Eq. (11). (a) SQNR versus OSR ( MHz); (b) SQNR versus quantum-signal center frequency (OSR = 12).
At OSR = 3, this boundary is 250 MHz, whereas the quantum-signal band extends from approximately 25 to 575 MHz. A substantial portion of the signal band therefore lies in the noise-amplification region, and the NTF, weighted by the receiver-filter response, yields higher in-band noise power than uniform quantization, with a greater penalty for second-order DSM. As OSR increases, the fixed quantum-signal band moves closer to the NTF zero in normalized frequency, enabling increasingly effective in-band noise suppression. Figure 2(b) uses a fixed 12-fold OSR and shows that the DSM is beneficial when the QKD center frequency is smaller than 1 GHz, when a smaller part of the QKD band is inside the DSM noise amplification region. This result indicates that the noise-suppression boundary at should not be treated as a hard limit for QKD band placement; instead, a joint design of the QKD center frequency, sampling rate, and matched-filter response is necessary. All results agree well with the theoretical curves given by (11).
We next examine the out-of-band spectral components observed after low-resolution quantization of the composite quantum-signal and pilot waveform. Figure 3(a) compares a 500-MBaud Gaussian-modulated waveform with a 500-MBaud QPSK test waveform; the latter is included as a diagnostic to clearly demonstrate the data-carrying structure of the spectral replicas. The simulation uses a sampling rate of 12 GSa/s, a quantum-signal center frequency of 300 MHz, a pilot frequency of 700 MHz, and a PSPR of 10. For illustration purposes only, Figure 3(a) compares 2-bit uniform quantization with 2-bit first-order DSM and clearly shows that the quantization produces several distinguishable spectral replicas in addition to the original signal at 300 MHz.
Figure 3. (a) Power spectral densities of QPSK and Gaussian-modulated waveforms under 2-bit quantization. Insets show the constellations of the main signal and the 1.1-GHz replica. (b) Correlation coefficients between the I and Q components of the 1.1-GHz replica and the corresponding components of the original test symbols versus oversampling ratio.
After separate downconversion, matched filtering, and downsampling, the QPSK replica centered at 1.1 GHz shows a recognizable constellation under uniform quantization, shown in the upper panel of Figure 3(a). We quantify the Pearson correlation coefficients between the replica and the original signals using Gaussian-modulated symbols and summarize the results in Table 2. We find strong same-quadrature linear correlations between corresponding I- and Q-components for uniform quantization, and a first-order DSM significantly reduces these correlations, which is also supported by the noise-like constellation at 1.1 GHz shown in the lower panel of Figure 3(a).
| No. | (GHz) | Uniform | Uniform | First-order DSM | First-order DSM |
| ① | 1.1 | −0.84 | 0.83 | ||
| ② | 3.1 | 0.86 | 0.86 | ||
| ③ | 3.9 | −0.66 | 0.54 | ||
| ④ | −1.7 | −0.81 | 0.81 | ||
| ⑤ | −2.5 | 0.85 | 0.84 | ||
| ⑥ | −4.5 | −0.58 | 0.58 |
Table 2. Correlation coefficients of out-of-band replicas for Gaussian modulation with uniform quantization and first-order DSM. Note: denotes the replica center frequency. and are the correlation coefficients of the real and imaginary sequences with their corresponding original sequences. The sampling rate is 12 GHz, and the quantizer resolution is 2 bits.
Figure 3(b) uses Gaussian modulation only and examines the same replica band at 1.1 GHz over the OSR sweep with 3–5-bit quantization. For uniform quantization, the correlation between signal and replica is pronounced only at 3 bits and is close to zero for 4 bits and above. With first-order DSM, the estimated correlations remain close to zero across all tested resolutions and OSRs. DSM therefore changes the structure of the correlated spectral components created by low-resolution quantization and strongly suppresses the linear correlation between the replica and the original symbols.
As shown in Figure 4, increasing the pilot frequency from 0.7 to 1.0 GHz in steps of 0.1 GHz, while keeping GHz fixed, shifts the replica center frequency from 1.1 to 1.7 GHz in steps of 0.2 GHz. These frequencies satisfy , and the I- and Q-component correlations have opposite signs, indicating that this replica is a third-order intermodulation product between the pilot tone and the quantum signal. Namely,
Figure 4. Simulated power spectral densities for different pilot frequencies. The quantum-signal center frequency is MHz, and the sampling rate is 12 GHz. (a) MHz; (b) MHz; (c) MHz; (d) MHz. Arrows indicate the quantum-signal center, the pilot, and the third-order intermodulation replica centered at .
where is the intermodulation coefficient.
Security Analysis
Source Model with Conjugate Leakage Mode
We now relate the measured linear replica component to a source-leakage model, following Jain et al. [31]. We restrict the analysis
to the selected replica band at , since we can always use additional electrical filters to suppress high-frequency replicas. Let and be independent Gaussian modulation variables with variance per quadrature, and define the coherent amplitude expressed in shot-noise units (SNU). We assume a balanced source prepared by Alice with DSM-induced leakage, expressed as
where is the intended signal, is the leakage mode, and is the relative amplitude ratio between replica and signal. For replica quadratures , with , the parameter is related to the measured correlation coefficients by
Here is the correlation coefficient discussed in Figure 3. Using for the identity matrix and , the source covariance is
For comparison, an ordinary leakage mode , as used in [31], corresponds to replacing with in the covariance matrix. Both sources, with ordinary or conjugate leakage mode, have the same leakage energy and the same information , where . However, their
joint information with a third signal mode need not be equal, because a conjugate state pair can support more informative joint measurements than an ordinary state pair [45]. Consequently, in our case, the joint source with a phase-conjugated leakage mode allows more information leakage to Eve.
Holevo Information and SKR Penalties
We model the attack as an independent thermal-loss channel with transmittance and input-referred excess noise . Eve holds the channel-environment output , the purification , and the leakage mode , and has an ideal phase reference for joint processing. The thermal environment variance is
In the mode ordering , the covariance matrix available to Eve is
where
Bob’s optical covariance is , with . The cross-covariance with Eve is
Bob’s detector efficiency and electronic noise are trusted receiver parameters. Using the heterodyne convention in which each detector’s normalized electronic-noise contribution is , the equivalent measurement noise is
Gaussian conditioning on Bob’s measurement gives [1]
If and are the three symplectic eigenvalues of and , respectively, the Holevo information with consideration of the DSM-induced leakage mode is
The Alice–Bob mutual information is
The asymptotic secret key rate (SKR) is given by
At fixed , , , and receiver parameters, Bob’s statistics and do not change with . The isolated leakage penalty, in the positive-key regime considered below, is therefore [31]
Figure 5 compares the SKR penalties for the ordinary and conjugate replicas. For , , and , the SKR penalties due to the conjugate leakage mode are approximately 4.38, 43.8, and 438 bit/s, respectively. The corresponding ordinary-leakage penalties are 0.797, 7.97, and 79.7 bit/s. Thus, in this weak-leakage interval, the conjugate-source penalty is approximately 5.5 times the ordinary-copy prediction, although both remain small compared with the final SKR. The penalty ratio is not universal and depends on the channel noise, loss, and leakage strength.
Figure 5. Asymptotic secret key rate penalty. The conjugate replica considered in our case is compared with the ordinary key reference [31] at the same . The parameters are , , , , , , MBaud.
Experimental Setup
Figure 6 shows the experimental Gaussian-modulated CVQKD system with a locally generated local oscillator (LO) at Bob. Alice uses a continuous-wave (CW) laser with a center wavelength of 1550 nm and a linewidth of 200 Hz as the coherent optical source. The transmitter first generates independent and identically distributed Gaussian random symbols at a symbol rate of 500 MBaud, then upsamples and pulse-shapes them using an RRC filter with a roll-off factor of 0.1. The shaped quantum signal is upconverted to 300 MHz and combined with a pilot tone at 750 MHz. The composite waveform is then digitally quantized using uniform quantization, first-order DSM, or second-order DSM. An arbitrary waveform generator (AWG) with a nominal 12-bit resolution and a maximum sampling rate of 12 GSa/s generates the electrical signal; the actual sampling rate is adjusted to the selected OSR. The I and Q outputs pass through external 1-GHz low-pass filters before driving a single-polarization IQ modulator that loads the composite waveform onto the optical carrier. A variable optical attenuator controls the launch power and sets the quantum-signal modulation variance to SNU. The modulated optical signal is transmitted to Bob through 20 km of standard single-mode fiber.
Figure 6. (a) Experimental setup and digital signal processing (DSP) for the experimental Gaussian-modulated CVQKD system. (b) Transmitter DSP, with one of three quantization schemes selected: -bit uniform quantization, first-order DSM, or second-order DSM. (c) Receiver DSP. AWG, arbitrary waveform generator; LPF, low-pass filter; IQ Mod, IQ modulator; VOA, variable optical attenuator; PC, polarization controller; OC, optical coupler; BPD, balanced photodetector; DSO, digital storage oscilloscope; CW, continuous wave.
Bob uses an independent CW laser with a 10 kHz linewidth as the local oscillator. The received signal and LO are combined in an optical coupler and measured by a 1.6 GHz balanced photodetector (BPD) for heterodyne coherent reception. A 10-bit oscilloscope sampling at 10 GSa/s captures the BPD electrical output. The receiver DSP performs carrier frequency offset (CFO) tracking, frame synchronization, and timing recovery, then separately downconverts the quantum and pilot signals to baseband. The quantum signal is matched-filtered and downsampled, while the pilot signal is filtered, and its phase is extracted for phase recovery [46].
The asymptotic secret key rate is calculated for reverse reconciliation and heterodyne detection using the Gaussian-modulated coherent-state CVQKD model [47, 48, 49] with the expression
where is the reverse reconciliation efficiency and is the fraction of Gaussian symbols used for key evaluation. The experimental parameters are as follows: , , detection efficiency , electronic noise , and channel transmittance . The detection efficiency and electronic noise are treated as trusted receiver parameters, whereas quantization- and DSM-induced noise contributions are included in the untrusted excess noise. The Holevo information is evaluated with experimentally measured to incorporate the DSM-induced leakage mode as detailed in the last section.
Results and Discussion
We use a 12 GSa/s AWG to emulate electrical waveforms with various quantization depths and OSRs. The waveform prepared digitally as double-precision floating-point and quantized directly by the AWG is considered as the full-resolution reference. To determine whether the DSM noise-shaped spectrum is retained at the physical electrical output, Figure 7 compares the PSD of the AWG-generated 3-bit quantized waveform, with or without DSM, captured directly by the oscilloscope. Although the oscilloscope bandwidth is 4 GHz, we show only up to 1.6 GHz to match the optical measurements shown below because this is the visible bandwidth of the BPD. Figure 7(a) shows the PSD of the quantized digital waveform input to the AWG, where the effect of NTF is clearly visible. The noise-suppression boundary is 2 GHz, 1/6 of the 12 GHz sampling rate. Figure 7(b) verifies that the AWG generates the designed waveform with high fidelity, the PSDs of which agree well with those shown in (a).
Figure 7. Normalized power spectral densities for 3-bit quantized (a) digital waveform at the AWG input; (b) AWG electrical output captured directly by the oscilloscope; (c) AWG electrical output captured by the oscilloscope after passing through an external 1-GHz low-pass filter.
Figure 10. Effects of DSM and quantizer resolution on the GM-LLO-CVQKD performance at different OSRs. The full resolution is measured separately at each OSR. Missing key-rate bars indicate that no positive estimate is obtained. (a) First-order DSM: excess noise referred to Alice’s side; (b) Second-order DSM: excess noise referred to Alice’s side; (c) First-order DSM: estimated key rate; (d) Second-order DSM: estimated key rate.
Figure 7(c) shows the PSD of the same waveform at the AWG output after passing through an analog electrical low-pass filter (LPF) with 1 GHz bandwidth. The LPF strongly suppresses high-frequency quantization noise and DSM-induced replicas. However, the replica at 1.2 GHz remains, and its variance must be measured as leakage mode to facilitate the SKR calculation. The characteristic spectral features observed in the digital domain remain identifiable at the electrical output, indicating that the quantization-noise shaping produced by the digital DSM survives the practical AWG output stage.
Figure 8 experimentally characterizes the leakage-mode strength of the replica centered at 1.2 GHz for uniform quantization and first-order DSM. The replica quadratures are recovered from optical measurements with the same DSP as the main signal and calibrated to Alice’s transmitter output. The measurements are performed using recovered symbols at each point with OSR = 24 and a PSPR of 10 dB. For 3-bit uniform quantization, the estimated is at the level of , indicating an SKR penalty of 3 Mb/s according to Figure 5. First-order DSM reduces to approximately , a four order-of-magnitude reduction. Increasing the resolution to 4 bits or more substantially reduces replica strength for both uniform quantization and first-order DSM, with negligible SKR penalties. Thus, under the tested conditions, DSM provides the most pronounced benefit at 3-bit resolution, whereas increasing the quantization resolution substantially reduces the difference between the two methods.
Figure 8. Experimentally estimated leakage-mode strength of the replica centered at 1.2 GHz versus the digitally imposed quantization resolution. Uniform quantization and first-order DSM are compared at OSR = 24 and a PSPR of 10 dB. The estimates are obtained from optical measurements and referred to Alice’s transmitter output. Each point represents the mean of the I- and Q-quadrature estimates from a single evaluation using symbols.
We continue to study the effects of quantizer resolution and OSR on excess noise and the asymptotic SKR. Figure 9 presents experimental results at 12-fold OSR, with representative values listed in Table 3. Low-resolution quantization without DSM substantially increases the total excess noise and severely reduces the key rate. For example, 3-bit uniform quantization produces 0.86 SNU excess noise and yields no positive SKR. First-order DSM lowers the excess noise to 0.13 SNU and restores the key rate to 12.28 Mbps. Second-order DSM further reduces the excess noise to 0.028 SNU and raises the key rate to 46.38 Mbps. Hence, a 3-bit DAC running at 12-fold OSR can deliver a positive key rate at a 20 km fiber range, making an appealing case for short-reach applications. With 4-bit second-order DSM, is 0.019 SNU and the estimated key rate is 50.11 Mbps, close to the full-resolution reference values of 0.016 SNU and 51.66 Mbps. As the resolution increases, second-order DSM progressively approaches full-resolution performance.
Figure 9. Effect of DSM and quantizer resolution on CVQKD performance, including (a) excess noise referred to Alice’s side; (b) estimated asymptotic key rate at OSR = 12. The 3- and 4-bit uniform quantization do not yield a positive key rate.
| Method | (SNU) | (Mbps) |
| 3-bit uniform quantization | 0.864 | No positive value |
| 3-bit first-order DSM | 0.126 | 12.28 |
| 3-bit second-order DSM | 0.028 | 46.38 |
| 4-bit second-order DSM | 0.019 | 50.11 |
| Full resolution | 0.016 | 51.66 |
Table 3. Representative experimental results at OSR = 12.
Figure 11. Effect of the linear PSPR and quantizer resolution on the GM-LLO-CVQKD performance of second-order DSM at OSR = 12. The quantum-signal power is held fixed while only the power of the 750-MHz pilot is varied. (a) Excess noise referred to Alice’s side; (b) Estimated asymptotic key rate.
Figure 10 shows the first- and second-order DSM results at various OSRs. Both designs working at OSR = 4 produce too much excess noise and yield no positive key rate with 3–6-bit quantization. At OSR = 6 and above, second-order DSM rapidly approaches full-resolution performance at all bit depths considered. The OSR requirement is more stringent for first-order DSM; even a 24-fold OSR does not recover a substantial key rate with 3-bit quantization. These results agree well with our analysis, as in Figure 2(a) and Eq. (11): at an insufficient sampling rate, the effective QKD band may cross the noise suppression boundary of the NTF, and amplified quantization noise will degrade the overall performance. Therefore, the quantizer resolution and DSM order must be selected jointly with the OSR, quantum-signal center frequency, and signal bandwidth to optimize system performance.
A second-order DSM generally outperforms a first-order DSM with the parameters considered in this work. In an engineering design, Eq. (11) can be evaluated with the implemented RRC response to select the minimum resolution and DSM order consistent with the system noise budget.
Figure 11 shows the experimental results for second-order DSM at OSR = 12 and various PSPR values. For the present pilot frequency, quantum-signal power, and receiver DSP, the favorable operating region is approximately PSPR = 10–20 in linear scale. Although higher PSPR reduces the quantum-signal dynamic range in the composite waveform and therefore worsens SQNR, laser phase noise dominates the observed performance degradation here. Random phase noise broadens the pilot spectrum, and its spectral tail causes crosstalk in the QKD band, a typical problem in frequency-multiplexed transmitter designs [50].
Conclusion
We have investigated transmitter-side delta–sigma noise shaping for low-resolution waveform generation in Gaussian-modulated CVQKD. By combining the DSM noise-transfer function with the receiver matched-filter response, we developed an in-band quantization-noise model that accounts for quantizer resolution, oversampling ratio, signal center frequency, and DSM order. For the structures considered here, the DSM suppresses quantization noise within , and increasing the DSM order provides stronger suppression. Therefore, system designers should choose the DAC sampling rate and QKD-band placement jointly so that a substantial part of the quantum-signal band lies within this noise-suppression region. We identify a nonlinear intermodulation product between the pilot and quantum signal as a phase-conjugated spectral replica that must be considered as a leakage mode during quantum state preparation. We thus develop a security model that relates this phase-conjugate replica to an additional key-rate penalty. Simulations and optical measurements show that the DSM strongly suppresses the measured amplitude of quantization-induced replicas, thereby reducing the key-rate penalty. Experiments conducted on a 500-MBaud CVQKD system over 20 km of optical fiber confirm that, at an oversampling rate of 12, a 3-bit second-order DSM restores a positive asymptotic secret key rate of 46.38 Mbps. With 4-bit second-order DSM, the estimated rate reaches 50.11 Mbps, approximately 97% of the 51.66 Mbps full-resolution reference. These results show that suitably designed noise shaping enables low-resolution waveforms to approach full-resolution key-rate performance while mitigating quantization-induced replica leakage within the linear-replica model. This provides a practical route toward lower-resolution CVQKD transmitters, supported by both an in-band noise model and a quantitative assessment of correlated spectral leakage.
Funding. This work was supported in part by the National Natural Science Foundation of China under Grant 62475297 and in part by the Guangdong Basic and Applied Basic Research Foundation under Grant 2024B1515020004.
Disclosures. The authors declare no conflicts of interest.
Data Availability Statement. Data underlying the results presented in this paper are not publicly available at this time but may be obtained from the authors upon reasonable request.
DSM NTF and Frequency Response
For the unity-coefficient CIFB structure considered here, the th-order state equations under the additive quantization-error model [35, 36] are
where , , and is the internal quantization error. With zero initial conditions and , the -transformed state equations become
Recursively eliminating the internal states and using gives
Since , the input-output relation reduces to
The NTF is therefore
Evaluating the NTF on the unit circle gives its frequency response:
References
- [1]C. Weedbrook, S. Pirandola, R. García-Patrón, et al., “Gaussian quantum information,” Rev. Mod. Phys. 84, 621–669 (2012).
- [2]F. Laudenbach et al., “Continuous-variable quantum key distribution with gaussian modulation—the theory of practical implementations,” Adv. Quantum Technol. 1, 1800011 (2018).
- [3]S. Pirandola et al., “Advances in quantum cryptography,” Adv. Opt. Photonics 12, 1012–1236 (2020).
- [4]G. Zhang et al., “An integrated silicon photonic chip platform for continuous-variable quantum key distribution,” Nat. Photonics 13, 839–842 (2019).
- [5]Y. Zhang, Y. Bian, Z. Li, et al., “Continuous-variable quantum key distribution system: Past, present, and future,” Appl. Phys. Rev. 11, 011318 (2024).DOI
- [6]T. Wang, P. Huang, L. Li, et al., “High key rate continuous-variable quantum key distribution using telecom optical components,” New J. Phys. 26, 023002 (2024).
- [7]A. A. E. Hajomer, C. Bruynsteen, I. Derkach, et al., “Continuous-variable quantum key distribution at 10 GBaud using an integrated photonic-electronic receiver,” Optica 11, 1197–1204 (2024).DOI
- [8]A. E. Hajomer, A. Bornhals, C. Bruynsteen, et al., “Chip-based 16 GBaud continuous-variable quantum key distribution,” Optica 13, 1035–1042 (2026).
- [9]S. Liu, Y. Jia, Y. Shi, et al., “Continuous-variable quantum key distribution over 50.4 km fiber using an integrated silicon photonic transmitter and receiver,” Photonics Res. 13, 3141–3150 (2025).DOI
- [10]X. Xu, L. Fan, Y. Pan, et al., “Gaussian-modulated continuous-variable quantum key distribution over 60 km fiber using an integrated silicon photonic receiver,” Opt. Lett. 51, 3485–3488 (2026).DOI
- [11]Y. Piétri, M. Schiavon, V. Marulanda Acosta, et al., “QOSST: A highly-modular open source platform for experimental continuous-variable quantum key distribution,” Quantum 8, 1575 (2024).DOI
- [12]B. Widrow, I. Kollár, and M.-C. Liu, “Statistical theory of quantization,” IEEE Trans. on Instrum. Meas. 45, 353–361 (1996).
- [13]S. Almonacid, F. Boitier, and P. Layer, “Performance model and design rules for optical systems employing low-resolution DAC/ADC,” J. Light. Technol. 38, 3007–3014 (2020).
- [14]P. Jouguet, S. Kunz-Jacques, E. Diamanti, and A. Leverrier, “Analysis of imperfections in practical continuous-variable quantum key distribution,” Phys. Rev. A 86, 032309 (2012).
- [15]R. Kumar, X. Tang, S. Ren, et al., “Performance of continuous variable quantum key distribution system at different detector bandwidth,” Opt. Commun. 471, 126034 (2020).DOI
- [16]H. Wang, Y. Li, T. Ye, et al., “High-rate continuous-variable quantum key distribution over 100 km fiber with composable security,” Optica 12, 1657–1667 (2025).arxiv.org/abs/2503.14843
- [17]B. Qi, P. Lougovski, R. Pooser, et al., “Generating the local oscillator “locally” in continuous-variable quantum key distribution based on coherent detection,” Phys. Rev. X 5, 041009 (2015).DOI
- [18]S. Kleis, M. Rueckmann, and C. G. Schaeffer, “Continuous variable quantum key distribution with a real local oscillator using simultaneous pilot signals,” Opt. Lett. 42, 1588–1591 (2017).
- [19]S. Ren, S. Yang, A. Wonfor, et al., “Demonstration of high-speed and low-complexity continuous variable quantum key distribution system with local oscillator,” Sci. Reports 11, 9454 (2021).
- [20]H.-M. Chin, N. Jain, D. Zibar, et al., “Machine learning aided carrier recovery in continuous-variable quantum key distribution,” npj Quantum Inf. 7, 20 (2021).DOI
- [21]S. Sarmiento, J. Tabares, and S. Etcheverry, “Low-complexity CV-QKD system with optical pilot-tone local oscillator synchronization,” Opt. Express 33, 50707–50717 (2025).
- [22]J. Lin, T. Upadhyaya, and N. Lütkenhaus, “Asymptotic security analysis of discrete-modulated continuous-variable quantum key distribution,” Phys. Rev. X 9, 041064 (2019).
- [23]M. Guo, P. Huang, L. Huang, et al., “Discrete-modulated coherent-state quantum key distribution with basis-encoding,” Research 8, 0691 (2025).DOI
- [24]Y. Pan, M. Wu, H. Wang, et al., “Long-distance discrete-modulated continuous-variable quantum key distribution over 126.56 km of fiber with a local local oscillator,” Commun. Phys. (2026). Published online 24 June 2026, https://doi.org/10.1038/s42005-026-02718-0.
- [25]H. Wang et al., “Sub-Gbps key rate for state continuous-variable quantum key distribution with metropolitan area,” Commun. Phys. 5, 162 (2022).
- [26]A. A. E. Hajomer, I. Derkach, N. Jain, et al., “Long-distance continuous-variable quantum key distribution over 100-km fiber with local local oscillator,” Sci. Adv. 10, eadi9474 (2024).
- [27]S. Matsenko, A. Ghasizaei, M. Jarzyna, et al., “Machine learning based optimization of CV-QKD under practical constraints,” arXiv:2606.31534 [quant-ph] (2026). Preprint.arxiv.org/abs/2606.31534
- [28]R. M. Gray and T. G. Stockham, Jr., “Dithered quantizers,” IEEE Trans. on Inf. Theory 39, 805–812 (1993).
- [29]A. A. Eielsen and A. J. Fleming, “Improving digital-to-analog converter linearity by large high-frequency dithering,” IEEE Trans. on Circuits Syst. I: Regul. Pap. 64, 1409–1420 (2017).DOI
- [30]I. Derkach, V. C. Usenko, and R. Filip, “Continuous-variable quantum key distribution with a leakage from state preparation,” Phys. Rev. A 96, 062309 (2017).
- [31]N. Jain, I. Derkach, H.-M. Chin, et al., “Modulation leakage vulnerability in continuous-variable quantum key distribution,” Quantum Sci. Technol. 6, 045001 (2021).DOI
- [32]A. A. E. Hajomer, N. Jain, H. Mani, et al., “Modulation leakage-free continuous-variable quantum key distribution,” npj Quantum Inf. 8, 136 (2022).arxiv.org/abs/2205.07245
- [33]X. Liu, J. Sun, T. Wang, et al., “Continuous-variable quantum key distribution with a leakage from digital-to-analog conversion,” npj Quantum Inf. (2026). Published online 25 June 2026, https://doi.org/10.1038/s41534-026-01309-9.
- [34]H. Inose, Y. Yasuda, and J. Murakami, “A telemetering system by code modulation—δ-σ modulation,” IRE Trans. on Space Electron. Telem. SET-8, 204–209 (1962).
- [35]R. M. Gray, “Oversampled sigma-delta modulation,” IEEE Trans. on Commun. 35, 481–489 (1987).
- [36]S. Pavan, R. Schreier, and G. C. Temes, Understanding Delta-Sigma Data Converters (Wiley-IEEE Press, 2017), 2nd ed.
- [37]J. Wang, Z. Jia, L. A. Campos, and C. Knittle, “Delta-sigma modulation for next generation fronthaul interface,” J. Light. Technol. 37, 2838–2850 (2019).DOI
- [38]X. Zeng, M. Fu, H. Jiang, et al., “Digital pre-distortion based on delta sigma modulation assisted look-up table for optical transmission,” J. Light. Technol. 41, 5827–5833 (2023).DOI
- [39]T. Xie, X. Xin, L. Fang, et al., “SC and OFDM hybrid coherent optical transmission scheme based on 1-bit bandpass delta-sigma modulation,” Opt. Express 32, 11337–11345 (2024).DOI
- [40]X. Yang, J. Yu, L. Zhang, et al., “High spectral efficiency 65536 QAM mobile fronthaul based on filtered delta-sigma modulation scheme,” J. Light. Technol. 43, 4546–4554 (2025).DOI
- [41]L. Zhong, Y. Zhao, S. Zhang, et al., “Channel-response-aware delta-sigma modulator design for low-resolution DAC-based pre-equalization systems,” Opt. Lett. 50, 6875–6878 (2025).DOI
- [42]Z. Chen, X. Wang, S. Yu, et al., “Continuous-mode quantum key distribution with digital signal processing,” npj Quantum Inf. 9, 28 (2023).
- [43]W. Fan, Z. Chao, X. Yi, and D. Wang, “Quantization noise shaping in CVQKD using delta-sigma modulation,” in 2026 31st OptoElectronics and Communications Conference (OECC), (2026). Paper P3-65.
- [44]Y. Pi, H. Wang, Y. Pan, et al., “Sub-mbps key-rate continuous-variable quantum key distribution with local local oscillator over 100-km fiber,” Opt. Lett. 48, 1766–1769 (2023).DOI
- [45]N. J. C. Lütkenhaus, I. B. K. Silber, “Phase conjugation of continuous quantum variables,” Phys. Rev. A 64, 032307 (2001).
- [46]J. Liao, W. Fan, J. Huang, et al., “Simple phase recovery using multi-pilot tones and wiener filters for continuous variable quantum key distribution,” Opt. Express 33, 35999–36014 (2025).DOI
- [47]I. Devetak and A. Winter, “Distillation of secret key and entanglement from quantum states,” Proc. Roy. Soc. A: Math. Phys. Eng. Sci. 461, 207–235 (2005).
- [48]M. Navascués, F. Grosshans, and A. Acín, “Optimality of gaussian attacks in continuous-variable quantum cryptography,” Phys. Rev. Lett. 97, 190502 (2006).
- [49]R. García-Patrón and N. J. Cerf, “Unconditional optimality of gaussian attacks against continuous-variable quantum key distribution,” Phys. Rev. Lett. 97, 190503 (2006).
- [50]G. Di Domenico, S. Schilt, and P. Thomann, “Simple approach to the relation between laser frequency noise and laser line shape,” Appl. Opt. 49, 4801–4807 (2010).










