betaFeedback

WorksPhysics and Astronomy

Dephasing-powered open quantum-dot battery

Abstract

We propose a simple realization of an open quantum battery powered by local dephasing. The setup consists of a triple-quantum-dot chain coupled at one end to a thermal reservoir, with the dot at the opposite end strongly detuned to form a high-energy storage element. Local dephasing populates this highly excited state and autonomously drives the system into a nonequilibrium steady state with high ergotropic efficiency. We find a limit where the ergotropic efficiency approaches unity, while the ergotropy itself approaches one-third of the energy detuning. We characterize the battery through its energy-storage performance, charging time, and stability, showing that the charged state remains long-lived after the dephasing source is switched off. We then demonstrate two complementary protocols for extracting the stored energy. First, nearly all the available ergotropy can be recovered through a simple cyclic unitary protocol involving only modulation of the detuned-dot gate. Second, coupling the detuned dot to an electronic load allows the extraction of electrochemical work exceeding the initial ergotropy, thereby accessing part of the battery's passive energy. Our results establish local dephasing as an autonomous resource for charging open quantum batteries and demonstrate simple routes for extracting the resulting stored energy in experimentally accessible mesoscopic platforms.

Introduction

A battery is a physical system that stores energy for later use. An effective battery stores a large amount of energy, retain it for sufficiently long times, and allow rapid charging and discharge. Quantum batteries seek to exploit quantum-mechanical effects to improve these figures of merit [1]. A central motivation has been the possibility of genuine quantum advantages arising from collective dynamics, coherence, and entanglement. Examples include superextensive scaling of the charging power with system size and corresponding reductions in charging time under collective charging protocols [2, 3, 4, 5].

An important distinction in this context is between energy stored in a system and energy that can actually be extracted as work. The latter is quantified by the ergotropy, defined as the maximum work extractable from a quantum state through a cyclic unitary transformation [6]. A wide variety of quantum-battery architectures and charging mechanisms has consequently been explored, including coherent driving [5], interaction-mediated collective charging [7], dissipative charging [8], thermalization-assisted protocols [9], and reservoir-engineered open quantum batteries [10]. In open quantum batteries, the environment itself participates in charging and stabilization, creating opportunities for autonomous control but also introducing dissipation and passive energy that reduce the useful fraction of the stored energy [11, 12, 13].

A particularly interesting source of nonequilibrium dynamics is dephasing. Although usually regarded as detrimental for suppressing quantum coherence, it can also redistribute population between energy eigenstates whenever the dephasing operator does not commute with the system Hamiltonian [14, 15]. Accordingly, there has been a growing interest in dephasing- and noise-assisted quantum batteries. Depending on the physical platform, environmental noise has been shown to accelerate charging, stabilize stored energy, improve robustness against disorder or parameter detuning, and even induce nontrivial steady-state charging dynamics [16, 17, 18, 19, 20]. More broadly, dissipative and nonequilibrium environments have emerged as useful energetic resources for quantum batteries, including common reservoirs, heat currents, and steady-state transport [21, 22, 23]. Dephasing can arise naturally from uncontrolled environmental fluctuations. Continuous quantum measurement represents a more engineered setting that can generate the same unconditional dephasing dynamics when the measurement

record is disregarded. Measurement backaction nevertheless provides a useful thermodynamic precedent, since it can supply energy to a quantum system and power thermodynamic processes [24, 25, 26, 27, 28, 29, 30].

In this work, we propose an open quantum battery in which energy is stored in the occupation of a highly excited electronic state. The battery, sketched in Figure 1, consists of a triple quantum dot (TQD) chain in the strong-Coulomb-blockade regime, such that at most one electron occupies the array [31, 32]. The leftmost quantum dot (QD1) is strongly detuned from the remaining dots and therefore provides the energy-storage element: charging the battery amounts to transferring population into the high-energy state predominantly localized on this dot. Local dephasing of QD1 supplies the energy required for this transfer by redistributing population among the TQD energy eigenstates. A thermal reservoir coupled to the opposite end of the array exchanges electrons efficiently with the low-energy states while coupling only weakly to the highly detuned state. The combination of dephasing-induced population transfer and state-selective reservoir coupling thereby produces the population imbalance required for a non-passive charged state.

Schematic of a dephasing-powered open quantum-dot battery and its quantum dot energy levels

Figure 1. Dephasing-powered open quantum battery consisting of a triple-quantum-dot chain. (a) The rightmost dot is coupled to an electron reservoir at temperature TT and chemical potential μ\mu with a tunneling strength Γ\Gamma. The leftmost dot is detuned by Δ\Delta, while the other two have a common energy ϵ\epsilon. A nearby dephasing source is coupled to it with strength γ\gamma and serves as the sole charging resource. (b) Schematic representation of the quantum dot levels (solid lines) and the hybridized eigenenergies EgE_g, EeE_e, and EdE_d (dashed lines).

Our goal is to populate this otherwise weakly occupied high-energy state rapidly, stabilize its occupation after charging, and provide a direct channel through which its stored energy can subsequently be discharged on demand.

Our results demonstrate that local dephasing can generate highly active nonequilibrium steady states, with an ergotropic efficiency approaching 1 in the low-temperature limit of the thermal reservoir. We further show that the charged state remains long-lived after dephasing is switched off. We demonstrate two complementary routes for extracting the stored energy. A simple cyclic modulation of the detuned-dot gate enables the extraction of nearly all the stored ergotropy. A complementary approach involves coupling the detuned dot to an electronic load, through which electrochemical work exceeding the initial ergotropy can be obtained by also drawing on the battery’s passive energy. Altogether, these findings establish local dephasing as an autonomous thermodynamic resource for charging open quantum batteries and provide an experimentally accessible platform based on mesoscopic quantum transport architectures.

The remainder of the manuscript is organized as follows. We present the model in § 1 and the charging dynamics in Sec. III, including the charging time and stability. The discharge of the battery into an electronic load and the resulting electrochemical work extraction are analyzed in § 1.2, followed by conclusions in § 1.3.

Model

The system of interest consists of a linear triple quantum dot (TQD), as shown in Figure 1. We consider nearest-neighbor hopping with amplitude Ω\Omega. Counting the quantum dots from left to right, as we do throughout the paper, QDs 2 and 3 have the same onsite energy ε\varepsilon, whereas QD1 is detuned upward by an energy Δ≫Ω\Delta\gg\Omega and acts as the energy-storage site. This configuration can be tuned through voltages applied to nearby plunger gates [33]. In the strong Coulomb blockade with up to one electron, the spin degree of freedom is irrelevant and will not be considered. In the local basis, the TQD Hamiltonian is

H^0=∑j=13(ε+Δδj1)d^j†d^j−∑j=12Ω(d^j†d^j+1+h.c.).(1)\hat{H}_0 = \sum_{j=1}^{3} \left(\varepsilon+\Delta\delta_{j1}\right)\hat{d}_j^\dagger\hat{d}_j-\sum_{j=1}^{2}\Omega\left(\hat{d}_j^\dagger\hat{d}_{j+1}+\mathrm{h.c.}\right). \tag*{(1)}

where d^j†\hat{d}_j^\dagger creates an electron on dot jj and δ\delta denotes the Kronecker delta.

QD3 is tunnel-coupled to a thermal reservoir, while the remaining dots are isolated from it. The reservoir is characterized by temperature TT and chemical potential μ\mu, with Hamiltonian H^res=∑kεkc^k†c^k\hat{H}_{\mathrm{res}}=\sum_k\varepsilon_k\hat{c}_k^\dagger\hat{c}_k. The tunnel coupling is described by H^tun=∑ktkd^3†c^k+h.c.\hat{H}_{\mathrm{tun}}=\sum_k t_k\hat{d}_3^\dagger\hat{c}_k+\mathrm{h.c.}, where c^k†\hat{c}_k^\dagger creates an electron in reservoir mode kk. In the weak-coupling regime, this interaction defines the bare tunneling energy scale Γ=2π∣ζ∣2ν\Gamma=2\pi\lvert\zeta\rvert^2\nu, where ν\nu is the reservoir density of states, assumed to be constant in the wide-band limit approximation. The corresponding physical tunneling rate is Γ/ℏ\Gamma/\hbar. Throughout the article, unless otherwise stated, we set the reservoir chemical potential to μ=ε\mu=\varepsilon, aligning it with the onsite energies of QDs 2 and 3.

As shown in Figure 1, we subject the detuned QD1 to local dephasing with strength γ\gamma. The dephasing source acts as the nonequilibrium external resource that supplies energy to the battery during charging, whereas the thermal reservoir supplies electrons. In the main text, we leave its microscopic origin unspecified and characterize it only through the dephasing strength γ\gamma. Two possible realizations are discussed in the appendices. One is a noisy resistor, for which Johnson–Nyquist voltage fluctuations generate local charge dephasing where the dephasing strength is proportional to the temperature and resistance of the resistor (see Appendix A). The other is continuous charge measurement using a quantum point contact [34], where the biased detector generates measurement backaction and the local dephasing strength is proportional to the charge fluctuations on QPC, or the signal-to-noise ratio for an efficient detector (see Appendix B). Although these implementations have different microscopic interpretations, they produce the same ensemble-averaged dephasing term considered here.

Eigenstates in the High-Detuning Regime

The exact eigenstates can be expressed in the local basis as ∣a⟩=ua∣1⟩+va∣2⟩+wa∣3⟩\lvert a\rangle=u_a\lvert1\rangle+v_a\lvert2\rangle+w_a\lvert3\rangle, although the coefficients have cumbersome expressions in terms of the system parameters. We are interested in the limit Δ≫Ω\Delta\gg\Omega, where the eigenstates of H^0\hat{H}_0, up to first order in Ω/Δ\Omega/\Delta, are

∣g⟩=(1+Ω22Δ2)−1/2(∣2⟩+∣3⟩2+Ω2Δ∣1⟩),∣e⟩=(1+Ω22Δ2)−1/2(∣2⟩−∣3⟩2+Ω2Δ∣1⟩),∣d⟩=(1+Ω2Δ2)−1/2(∣1⟩−ΩΔ∣2⟩).(2)\begin{aligned} |g\rangle&= \left(1+\frac{\Omega^2}{2\Delta^2}\right)^{-1/2}\left(\frac{|2\rangle+|3\rangle}{\sqrt{2}}+\frac{\Omega}{\sqrt{2}\Delta}|1\rangle\right),\\ |e\rangle&= \left(1+\frac{\Omega^2}{2\Delta^2}\right)^{-1/2}\left(\frac{|2\rangle-|3\rangle}{\sqrt{2}}+\frac{\Omega}{\sqrt{2}\Delta}|1\rangle\right),\\ |d\rangle&= \left(1+\frac{\Omega^2}{\Delta^2}\right)^{-1/2}\left(|1\rangle-\frac{\Omega}{\Delta}|2\rangle\right). \tag*{(2)} \end{aligned}

The state ∣d⟩|d\rangle is the highly detuned eigenstate and is predominantly localized on QD1. The other two eigenstates, ∣g⟩|g\rangle and ∣e⟩|e\rangle, are primarily symmetric and antisymmetric combinations of QDs 2 and 3, respectively, and therefore have substantial overlap with the reservoir-coupled QD3. The high-energy state ∣d⟩|d\rangle has only a small admixture of the low-energy dots, of order Ω/Δ\Omega/\Delta, which strongly suppresses its coupling to the reservoir.

Taking the ground-state energy as the reference, Eg=0E_g=0, fixes the common onsite energy ε\varepsilon accordingly. In the high-detuning limit, the remaining eigenenergies are separated into a low-energy state ∣e⟩|e\rangle at an energy of order 2Ω2\Omega and a highly excited state ∣d⟩|d\rangle at an energy of order Δ\Delta, cf. Figure 1b where the energy levels EgE_g, EeE_e, and EdE_d are indicated with dashed lines. To leading order in Ω/Δ\Omega/\Delta, the large energy separation of ∣d⟩|d\rangle from the low-energy subspace is therefore controlled directly by the gate detuning Δ\Delta. Note that our choice of the chemical potential, μ=ε\mu=\varepsilon, places it approximately midway between EgE_g and EeE_e.

The large separation of ∣d⟩|d\rangle from the two low-energy states makes its occupation energetically unfavorable under ordinary coherent dynamics. Its hybridization with the low-energy subspace is suppressed by Ω/Δ\Omega/\Delta, and its overlap with the reservoir-coupled QD3 is of order O(Ω2/Δ2)O(\Omega^2/\Delta^2). This separation is central to the battery operation: local dephasing can populate the high-energy state during charging, whereas its weak reservoir coupling (mediated by higher-order tunneling processes involving the two intermediate dots) protects the stored excitation once the dephasing source is removed.

Passive energy and ergotropy

The useful energy stored in the battery is quantified by its ergotropy, defined relative to the corresponding passive state. We first compute the total internal energy

E(t)=Tr⁡[H^0ρ^(t)],(3)E(t)=\operatorname{Tr}\left[\hat{H}_0\hat{\rho}(t)\right], \tag*{(3)}

where the reduced density matrix of the TQD, ρ^(t)\hat{\rho}(t), describes the evolution of the system state.

The passive state is obtained by arranging the eigenvalues of ρ^(t)\hat{\rho}(t) in decreasing order over the energy eigenstates of H^0\hat{H}_0 in increasing order of energy. Its energy is therefore

Epassive(t)=∑nrn(t)En,(4)E_{\mathrm{passive}}(t)=\sum_n r_n(t)E_n, \tag*{(4)}

where rn(t)r_n(t) are the eigenvalues of ρ^(t)\hat{\rho}(t) sorted in decreasing order and EnE_n are the eigenenergies of H^0\hat{H}_0 sorted in increasing order. The ergotropy is then [6]

W(t)=E(t)−Epassive(t),(5)W(t)=E(t)-E_{\mathrm{passive}}(t), \tag*{(5)}

which is nonnegative by construction. A state is active, and can therefore serve as a source of extractable work under cyclic unitary operations, when W(t)>0W(t)>0.

Open-System Dynamics

We describe the ensemble-averaged dynamics using a global Lindblad master equation formulated in the eigenbasis of the coupled-dot Hamiltonian. This treatment incorporates interdot hybridization into the reservoir-induced transition rates and provides a thermodynamically consistent weak-coupling description when the coherent coupling between the dots cannot be neglected [35, 36, 37, 38]. The global master equation is valid in the weak system–reservoir coupling regime, where the reservoir-induced transition rates are small compared to the relevant energy-level splittings, and under the usual Born–Markov and secular approximations.

The reduced density matrix evolves according to [39]

dρ^dt=−iℏ[H^0,ρ^]+1ℏ[∑a(D[L^ain]+D[L^aout])+D[L^γ]]ρ^,(6)\frac{d\hat{\rho}}{dt}=-\frac{i}{\hbar}[\hat{H}_0,\hat{\rho}]+\frac{1}{\hbar}\left[\sum_a\left(\mathcal{D}[\hat{L}_a^{\mathrm{in}}]+\mathcal{D}[\hat{L}_a^{\mathrm{out}}]\right)+\mathcal{D}[\hat{L}_\gamma]\right]\hat{\rho}, \tag*{(6)}

where D[O^]ρ^=O^ρ^O^†−{O^†O^,ρ^}/2\mathcal{D}[\hat{O}]\hat{\rho}=\hat{O}\hat{\rho}\hat{O}^{\dagger}-\{\hat{O}^{\dagger}\hat{O},\hat{\rho}\}/2 and a∈{g,e,d}a\in\{g,e,d\}. Since the reservoir is coupled only to QD3, particle injection and extraction are described by the jump operators

L^ain=Wa0 ∣a⟩⟨0∣,L^aout=W0a ∣0⟩⟨a∣,(7)\hat{L}_a^{\mathrm{in}}=\sqrt{W_{a0}}\,|a\rangle\langle0|,\qquad\hat{L}_a^{\mathrm{out}}=\sqrt{W_{0a}}\,|0\rangle\langle a|, \tag*{(7)}

where the tunneling strengths involving eigenstate ∣a⟩|a\rangle,

Wa0=Γ∣wa∣2f(Ea),W0a=Γ∣wa∣2[1−f(Ea)],(8)W_{a0}=\Gamma|w_a|^2f(E_a),\qquad W_{0a}=\Gamma|w_a|^2[1-f(E_a)], \tag*{(8)}

where wa=⟨3∣a⟩w_a=\langle3|a\rangle denotes the overlap of eigenstate ∣a⟩|a\rangle with the local state of the reservoir-coupled QD3 [40]. Here f(E)=[1+exp⁡((E−μ)/kBT)]−1f(E)=[1+\exp((E-\mu)/k_BT)]^{-1} is the Fermi–Dirac distribution describing the thermal state of the reservoir with temperature TT and electrochemical potential μ\mu.

The reservoir selectivity follows directly from the overlaps waw_a. The states ∣g⟩|g\rangle and ∣e⟩|e\rangle are predominantly supported on QDs 2 and 3 and therefore both have substantial overlap with the reservoir-coupled QD3. By contrast, the highly detuned state ∣d⟩|d\rangle is predominantly localized on QD1, and its amplitude on QD3 is of order O(Ω2/Δ2)O(\Omega^2/\Delta^2), and hence does not appear at the order given in Eq. (2). Population transferred into ∣d⟩|d\rangle therefore exchanges particles with the reservoir much more slowly than population in the low-energy states, allowing energy deposited in the detuned state to remain stored in the TQD.

Local dephasing strongly modifies this virtual-transport picture by coupling ∣d⟩|d\rangle to the low-energy eigenstates. The dephasing operator, generated by the barrier-dot occupation operator, n^1=d^1†d^1\hat{n}_1 = \hat{d}_1^\dagger\hat{d}_1, is, in the energy eigenbasis:

L^γ=γn^1=γ∑a,bua∗ub ∣a⟩⟨b∣,(9)\hat{L}_{\gamma} = \sqrt{\gamma}\hat{n}_1 = \sqrt{\gamma}\sum_{a,b}u_a^*u_b\,|a\rangle\langle b|, \tag*{(9)}

where ua=⟨1∣a⟩u_a = \langle1|a\rangle and ub=⟨1∣b⟩u_b = \langle1|b\rangle denote the overlaps of the energy eigenstates with the local state of QD1, cf. Eq. (2). Although n^1\hat{n}_1 is diagonal in the local occupation basis, it is nondiagonal in the energy eigenbasis because [n^1,H^0]≠0[\hat{n}_1,\hat{H}_0] \ne0. The dephasing channel therefore conserves particle number while redistributing populations among the single-electron energy eigenstates. In particular, the off-diagonal components of n^1\hat{n}_1 couple the predominantly localized high-energy state ∣d⟩|d\rangle to the low-energy states ∣g⟩|g\rangle and ∣e⟩|e\rangle. Local dephasing can consequently transfer population from the reservoir-accessible low-energy subspace into the highly excited state without directly injecting an additional electron into the TQD. Note that Γ\Gamma and γ\gamma are expressed in energy units, so that the corresponding physical rates are obtained by dividing by ℏ\hbar in Eq. (6).

In previous works, the same basic mechanism was shown to enhance the occupation of an otherwise weakly occupied detuned state and to modify transport through triple-quantum-dot systems [14, 15, 29]. The present configuration uses this effect for a different purpose. Rather than placing the detuned dot between two transport sites, we place the highly excited state at one end of the TQD and couple a single thermal reservoir to the opposite end. The resulting spatial separation makes the low-energy states strongly reservoir accessible while the detuned state remains only weakly coupled to the reservoir. Dephasing can therefore populate the high-energy state faster than the reservoir can empty it, producing the nonequilibrium population ordering required for a non-passive steady state.

Dephasing-Induced Charging and Battery Performance

We now investigate the charging properties of the dephasing-powered quantum battery. Unless stated otherwise, we consider a strongly detuned storage dot with Δ=100Ω\Delta= 100\Omega, reservoir coupling Γ=0.1Ω\Gamma= 0.1\Omega, reservoir temperature kBT=Ωk_{\mathrm{B}}T = \Omega, and chemical potential aligned with the low-energy onsite level, μ=ϵ\mu= \epsilon. Local dephasing acts on QD1 with strength γ=10Ω\gamma= 10\Omega, while the remaining dots are not directly dephased. These parameters place the system deeply in the high-detuning regime, where the excited state localized on QD1 is only weakly hybridized with the reservoir-accessible low-energy states. Dephasing of the other individual dots is compared in Appendix C.

this state and the low-energy manifold. Dephasing of the other individual dots is compared in Appendix C.

We employ a single-orbital approximation which is also consistent with typical GaAs/AlGaAs energy scales. In these devices, the interdott hopping can be tuned to the μeV\mu\mathrm{eV} range [41, 42], and bath coupling can be made smaller, of order 0.1 μeV0.1~\mu\mathrm{eV} [43]. At the same time, the first orbital excitation is typically much larger, in the meV\mathrm{meV} range [44, 45]. Thus, a physical scale Ω∼1 μeV\Omega\sim1~\mu\mathrm{eV} gives Γ=0.1Ω∼0.1 μeV\Gamma= 0.1\Omega\sim0.1~\mu\mathrm{eV} and Δ=100Ω∼0.1 meV\Delta= 100\Omega\sim0.1~\mathrm{meV}, while the first excited orbital remains more than an order-of-magnitude above the detuned state. Therefore, higher local orbitals are not expected to participate in the dynamics considered here.

We also checked that the charging dynamics remain confined predominantly to the empty and single-electron sectors. Although dephasing can redistribute population within a fixed charge subspace, it does not itself change the total particle number. Population of higher-charge sectors is instead controlled by particle injection from the reservoir and by the corresponding charging-energy cost. Using a spinful extended-Hubbard model including all two-electron states, we find that the two-electron occupation remains negligible over the reservoir window μ/Ω∈[−0.5,0.5]\mu/\Omega\in[-0.5, 0.5] and kBT/Ω∈[0.1,5]k_{\mathrm{B}}T/\Omega\in[0.1, 5] (see Appendix § 2).

Figure 2 summarizes the charging dynamics. The evolution is obtained from the global master equation presented in § 1 C. Starting from thermal equilibrium with the reservoir, dephasing drives the system away from equilibrium and steadily increases its internal energy. Figure 2(a) shows the populations of the empty state and the three single-electron energy eigenstates of H^0\hat{H}_0. Dephasing transfers substantial population into the high-energy detuned state ∣d⟩\lvert d\rangle, while the reservoir continues to exchange particles efficiently with the low-energy states ∣g⟩\lvert g\rangle and ∣e⟩\lvert e\rangle. With μ=ε\mu=\varepsilon lying approximately midway between these two states, the reservoir preferentially populates the lower-energy bonding state ∣g⟩\lvert g\rangle, leaving the antibonding state ∣e⟩\lvert e\rangle relatively weakly occupied. Together with the substantial occupation of ∣d⟩\lvert d\rangle induced by dephasing, this population distribution produces a highly non-passive steady state.

Charging dynamics of the dephasing-powered quantum battery

Figure 2. Charging dynamics of the dephasing-powered quantum battery for Δ=100Ω\Delta= 100\Omega, Γ=0.1Ω\Gamma= 0.1\Omega, kBT=Ωk_{\mathrm{B}}T = \Omega, μ=ϵ\mu= \epsilon, and γ=10Ω\gamma= 10\Omega. (a) Populations of the empty state and the three single-electron energy eigenstates. (b) Internal energy E=Tr⁡(H^0ρ^)E = \operatorname{Tr}(\hat{H}_0\hat{\rho}), passive-state energy EpassiveE_{\mathrm{passive}}, and ergotropy W\mathcal{W}. Dephasing drives the system into a highly excited non-equilibrium steady state while maintaining a large extractable-work component. (c) Ergotropic efficiency W/E\mathcal{W}/E, which approaches ≈73%\approx73\% in the steady state.

The internal energy increases monotonically before saturating to a nonequilibrium steady-state value substantially above the equilibrium energy, see Figure 2(b). Importantly, most of the injected energy remains available as extractable work rather than being converted into passive energy.

The delayed onset of ergotropy marks the time at which the state first becomes non-passive. At early times, dephasing raises the internal energy, but the population distribution remains passive and therefore contains no extractable work. The ergotropic efficiency W/EW/E is shown in Figure 2(c). After an initial transient, the efficiency rapidly increases and approaches a steady-state value exceeding 70%. This result is remarkable because open-system batteries coupled to thermal reservoirs typically suffer from a large passive-energy contribution that significantly reduces the extractable fraction of the stored energy.

Once the battery has been charged, the dephasing source can be switched off, as the charged state remains protected by the large energy detuning. Specifically, the decay rates of the eigenstates (2) into the reservoir, proportional to ∣wa∣2Γ\lvert w_a\rvert^2\Gamma, are strongly suppressed for the charged state, resulting in W0d=ΓO(Ω4/Δ4)W_{0d}=\Gamma O(\Omega^4/\Delta^4). The long-term stability of the stored energy is examined in Sec. III C.

For the parameters considered here, the steady-state battery energy reaches approximately Ess≃27.76ΩE_{\mathrm{ss}}\simeq27.76\Omega, of which about Wss≃20.17ΩW_{\mathrm{ss}}\simeq20.17\Omega remains extractable, corresponding to an ergotropic efficiency of approximately 0.73. The large ergotropy is primarily caused by the dephasing-induced population of the highly detuned state ∣d⟩\lvert d\rangle. In the steady state, its population reaches pd≃0.27p_d\simeq0.27 despite lying roughly Δ=100Ω\Delta=100\Omega above the low-energy subspace, whereas the remaining populations are approximately p0≃0.18p_0\simeq0.18, pg≃0.48p_g\simeq0.48, and pe≃0.07p_e\simeq0.07. The resulting occupation of the highest-energy state is therefore far larger than would occur in thermal equilibrium and produces a strongly non-passive population distribution.

It is instructive to compare the present mechanism with our earlier works on measurement-assisted tunneling in triple-quantum-dot architectures [14, 15, 29]. In those systems, the strongly detuned state was associated with the central dot and measurement-induced dephasing converted its otherwise virtual occupation into real population, thereby modifying transport through the array. Here we use a different geometry and operating principle: the detuned state is localized on the end dot QD1, while the only thermal reservoir is attached to the opposite end, QD3. The low-energy states therefore remain strongly coupled to the reservoir, whereas the high-energy storage state is nearly isolated from it. This state-selective coupling allows dephasing-induced excitation of ∣d⟩\lvert d\rangle to accumulate as a persistent population imbalance and produces a non-passive steady state with large ergotropy.

Steady-State Performance

We now examine the steady-state battery performance over a broader parameter range. Figure 3 shows the steady-state internal energy EssE_{\mathrm{ss}} and ergotropic efficiency Wss/EssW_{\mathrm{ss}}/E_{\mathrm{ss}} as a function of the barrier detuning Δ\Delta, for different dephasing strengths γ\gamma, with all other parameters kept fixed at Γ=0.1Ω\Gamma=0.1\Omega, kBT=Ωk_{\mathrm{B}}T=\Omega, and μ=ε\mu=\varepsilon. The steady-state energy is controlled primarily by the barrier detuning. Increasing Δ\Delta raises the energy of the barrier-like state and therefore increases the energy stored when this state is populated, as seen in Figure 3(a). The ergotropy increases linearly with Δ\Delta for Δ≳100 Ω\Delta\gtrsim100\,\Omega, since the internal energy increases linearly in Figure 3(a) and ergotropic efficiency becomes constant in Figure 3(b). This linear scaling is expected to hold only while Δ\Delta remains well below the orbital excitation energies of QD2 and QD3, beyond which the single-orbital approximation may no longer be valid.

Steady-state battery performance as a function of barrier detuning for different dephasing strengths

Figure 3. Steady-state battery performance as a function of barrier detuning Δ\Delta, for different cases of dephasing strength γ\gamma. The remaining parameters are fixed at Γ=0.1Ω\Gamma=0.1\Omega, kBT=Ωk_{\mathrm{B}}T=\Omega, and μ=ε\mu=\varepsilon, with dephasing acting on the barrier dot. Panel (a): steady-state internal energy Ess/ΩE_{\mathrm{ss}}/\Omega. The stored energy increases mainly with Δ\Delta, reflecting the increasing energy of the populated barrier-like state, while its dependence on γ\gamma is much weaker. Panel (b): ergotropic efficiency Wss/EssW_{\mathrm{ss}}/E_{\mathrm{ss}}. The efficiency remains high over a broad parameter range, indicating that the dephasing-induced active state is robust against changes in Δ\Delta and γ\gamma.

By contrast, the dependence on γ\gamma is weak over the range shown: changing the dephasing strength modifies the steady-state energy negligibly compared to changing Δ\Delta. The ergotropic efficiency shows a similar behavior, see Figure 3(b). It remains large over a broad region of parameter space and varies only weakly with γ\gamma. Thus, the high extractable fraction is not a fine-tuned feature; it lies within a broad plateau where the steady state remains strongly non-passive.

In the large-detuning regime, the steady-state energy and ergotropy have compact analytic expressions to leading order in Ω/Δ\Omega/\Delta. Unlike the numerical calculations, we leave the reservoir temperature TT arbitrary in this analysis. For chemical potentials between the two low-energy eigenstates, Eg<μ<EeE_g < \mu< E_e, the steady-state energy and ergotropy to leading order in Ω/Δ\Omega/\Delta are

Ess≃e(μ−ε)/kBTcosh⁡(ΩkBT)1+3e(μ−ε)/kBTcosh⁡(ΩkBT)Δ,Wss≃e(μ−ε)/kBTsinh⁡(ΩkBT)1+3e(μ−ε)/kBTcosh⁡(ΩkBT)Δ.(10)\begin{aligned} E_{\mathrm{ss}} &\simeq\frac{e^{(\mu-\varepsilon)/k_{\mathrm B}T}\cosh\left(\frac{\Omega}{k_{\mathrm B}T}\right)}{1+3e^{(\mu-\varepsilon)/k_{\mathrm B}T}\cosh\left(\frac{\Omega}{k_{\mathrm B}T}\right)}\Delta,\\ \mathcal{W}_{\mathrm{ss}} &\simeq\frac{e^{(\mu-\varepsilon)/k_{\mathrm B}T}\sinh\left(\frac{\Omega}{k_{\mathrm B}T}\right)}{1+3e^{(\mu-\varepsilon)/k_{\mathrm B}T}\cosh\left(\frac{\Omega}{k_{\mathrm B}T}\right)}\Delta. \tag*{(10)} \end{aligned}

The corresponding ergotropic efficiency approaches

WssEss≃tanh⁡(ΩkBT).(11)\frac{\mathcal{W}_{\mathrm{ss}}}{E_{\mathrm{ss}}}\simeq\tanh\left(\frac{\Omega}{k_{\mathrm B}T}\right). \tag*{(11)}

For μ=ε\mu=\varepsilon and kBT=Ωk_{\mathrm B}T=\Omega, this gives an ergotropic efficiency of approximately 0.76, close to the numerical value of 0.73 obtained in Figure 2. These expressions explain the nearly linear increase of the stored energy and ergotropy with Δ\Delta, as well as the saturation of the ergotropic efficiency at large detuning. Interestingly, the leading-order ergotropic efficiency is independent of the reservoir chemical potential μ\mu, even though the stored energy depends on it. In the limit where kBT≪Ωk_{\mathrm B}T\ll\Omega, these expressions predict that the ergotropic efficiency approaches unity, while the stored energy approaches Δ/3\Delta/3.

Although the final steady-state energy and efficiency are only weakly affected by γ\gamma, the charging time of the battery is strongly controlled by the dephasing strength, which we examine below.

Charging Time

To see whether γ\gamma affects the charging rate, we define an ergotropic charging time

τW=min⁡{t:W(t)Wss≥0.95}.(12)\tau_{\mathcal{W}}=\min\left\{t:\frac{\mathcal{W}(t)}{\mathcal{W}_{\mathrm{ss}}}\geq0.95\right\}. \tag*{(12)}

where the initial thermal state has zero ergotropy. This definition focuses on the time required to generate useful extractable work, rather than merely the time required to increase the internal energy. Figure 4 shows τW\tau_{\mathcal{W}} as a function of the dephasing strength for several barrier detunings. The charging time decreases approximately as a power law with increasing γ\gamma, showing that dephasing controls the rate at which the active nonequilibrium state is produced. Larger detuning leads to longer charging times because the detuned state is more weakly hybridized with the low-energy states. As a result, dephasing-induced population transfer into the detuned state becomes slower. Across the detunings shown, increasing γ\gamma consistently shortens τW\tau_{\mathcal{W}}, while increasing Δ\Delta shifts the curves upward.

Ergotropic charging time as a function of dephasing strength for several barrier detunings

Figure 4. Ergotropic charging time as a function of dephasing strength for several barrier detunings. Increasing the dephasing strength substantially reduces the charging time, showing that γ\gamma provides a kinetic control knob for the battery. Larger detuning slows the charging process because the high-energy barrier state is more weakly hybridized with the low-energy states. Parameters: Γ=0.1Ω\Gamma=0.1\Omega, kBT=Ωk_{\mathrm B}T=\Omega, and μ=ε\mu=\varepsilon.

In the large-detuning regime, the dephasing-induced transition rates into the storage state scale as γΩ2/Δ2\gamma\Omega^2/\Delta^2. Since these transitions control the slow charging dynamics, charging time scales as τW∼Δ2/(γΩ2)\tau_{\mathcal{W}}\sim\Delta^2/(\gamma\Omega^2), explaining the approximately inverse dependence on the dephasing strength observed in Figure 4.

The dephasing strength is an experimentally tunable parameter. In the noisy-resistor realization discussed in Appendix A, increasing γ\gamma corresponds to increasing the voltage fluctuations seen by the dots, for example by increasing the effective noise temperature, resistance, or capacitive lever arm. In the continuous-measurement realization discussed in Appendix B, increasing γ\gamma corresponds to increasing the measurement strength, which can be achieved by increasing the detector response or the QPC bias, within the regime where the Markovian dephasing description remains valid.

Stability of the Charged Battery

A practically useful quantum battery must retain its stored energy after the charging process has been terminated. To assess the stability of the charged state, we investigate the relaxation dynamics following the removal of the dephasing source. The battery is first charged until its ergotropy reaches 95% of the steady-state value. The dephasing is then switched off (γ=0\gamma= 0), while the Hamiltonian, reservoir coupling, chemical potentials, and temperatures remain unchanged. The subsequent dynamics therefore describe the natural relaxation of the charged battery in the absence of dephasing.

Figure 5(a) shows the evolution of the internal energy, passive energy, and ergotropy after the dephasing source is removed. Over the time window shown, the battery remains stable in the charged state: the internal energy, ergotropy, and passive energy remain essentially unchanged. This stability arises because the large detuning Δ≫Ω\Delta\gg\Omega localizes the high-energy eigenstate ∣d⟩\lvert d\rangle predominantly on QD1, while the thermal reservoir is coupled only to the distant QD3. The overlap of ∣d⟩\lvert d\rangle with the reservoir contact is consequently O(Ω2/Δ2)\mathcal{O}(\Omega^2/\Delta^2), strongly inhibiting relaxation of the stored excitation through the reservoir. Thus, dephasing can be switched off during storage without appreciable loss of the stored work over the interval considered here.

For the representative scale Ω=1 μeV\Omega= 1\,\mu\mathrm{eV}, the reservoir temperature kBT=Ωk_{\mathrm{B}}T = \Omega corresponds to approximately 11.6mK, while the upper limit Ωt/ℏ=106\Omega t/\hbar= 10^6 corresponds to approximately 0.66ms. The negligible decay observed over this interval shows that relaxation through the thermal electronic reservoir is not expected to limit the battery lifetime on this timescale.

A common source of relaxation in semiconductor quantum dots is electron–phonon coupling, which can induce transitions between the energy eigenstates. To examine its effect on storage stability, we introduce phenomenological phonon-induced transitions from the high-energy state ∣d⟩\lvert d\rangle to the low-energy states ∣g⟩\lvert g\rangle and ∣e⟩\lvert e\rangle, characterized by a total spontaneous emission rate κph/ℏ\kappa_{\mathrm{ph}}/\hbar (see Appendix E). Figure 5(b) shows the resulting ergotropy retention for κph/Ω=10−6,10−5,\kappa_{\mathrm{ph}}/\Omega= 10^{-6}, 10^{-5}, and 10−410^{-4}. We have verified numerically that including phonon relaxation even at κph=10−4Ω\kappa_{\mathrm{ph}} = 10^{-4}\Omega produces only small corrections to the steady-state ergotropy and internal energy. For example, the ergotropic efficiency decreases by 3.6% for the parameters in Figure 2. Thus, phonon relaxation is neglected elsewhere in the manuscript.

Experiments on GaAs double quantum dots have reported strongly suppressed phonon-assisted tunneling, with dimensionless relaxation strength κph/Ω\kappa_{\mathrm{ph}}/\Omega as low as approximately 3×10−63 \times10^{-6} [46]. Although this motivates the range considered here, the experimental device operates with substantially smaller interdott hopping, and the effective phonon relaxation rate depends on the device geometry and electronic spectrum. The achievable rate in the present TQD architecture therefore remains device-dependent. As shown in Figure 5(b), the storage lifetime decreases approximately inversely with κph\kappa_{\mathrm{ph}}, while substantial ergotropy can still be retained over timescales much longer than the characteristic tunneling time.

Stability of the charged quantum battery

Figure 5. Stability of the charged quantum battery after the dephasing source is switched off. (a) Internal energy EE, passive energy EpassiveE_{\mathrm{passive}}, and ergotropy WW in the absence of phonon relaxation, demonstrating strongly suppressed relaxation through the thermal reservoir. (b) Ergotropy retention in the presence of phonon-induced relaxation for different values of κph\kappa_{\mathrm{ph}}. In each case, phonon relaxation is included during both charging and storage, and the battery is initially charged to 95% of its corresponding steady-state ergotropy. Other parameters are the same as in Figure 2.

Discharging the Quantum Battery

We next examine how the energy stored by dephasing-induced charging can be released as useful work. We consider two complementary discharge protocols. First, we study cyclic unitary extraction, for which the ergotropy provides the fundamental upper bound on the extractable work. Remarkably, approaching this bound does not require a complicated optimal control sequence: nearly all of the stored ergotropy can be extracted through a simple and intuitive protocol involving only the plunger gate of the detuned dot. The gate is rapidly lowered to bring the dot near resonance, the system is allowed to evolve coherently, and the gate is then raised back to its initial value, completing a cyclic transformation of the Hamiltonian. We then consider an open-system protocol in which QD1 is coupled to an electronic load. In this case, particle exchange with the load allows the stored energy to be converted directly into electrochemical work. Unlike cyclic unitary extraction, this process is not bounded by the initial ergotropy and can also access part of the passive energy of the battery.

Cyclic Unitary Discharge

The maximum work extractable from the charged state through a cyclic unitary transformation is given by its ergotropy. The corresponding optimal transformation maps the charged state onto its passive state while returning the Hamiltonian to its initial form, reducing the battery energy by exactly

Wextmax⁡=W(0)=E(0)−Epassive(0).(13)W_{\mathrm{ext}}^{\max} = \mathcal{W}(0) = E(0) - E_{\mathrm{passive}}(0). \tag*{(13)}

Although this provides a natural benchmark for discharge, implementing the general optimal unitary may require independent control of several transitions. We therefore ask how much of the ergotropy can instead be accessed through a simple control already available in a quantum-dot device: modulation of the plunger gate controlling the detuned QD1.

We consider a cyclic protocol in which the energy of the storage dot is lowered while it remains highly occupied, allowing work to be extracted from the battery. The system is then allowed to evolve coherently at a lower detuning, redistributing population away from the storage dot. Finally, its energy is raised back to the original value. If the occupation of the storage dot is sufficiently reduced before the return, less work is required to restore its energy than was extracted during the initial reduction, resulting in positive net work over the cycle.

To implement this protocol, we first disconnect the dephasing source and the reservoir, so that the battery evolves unitarily. We then control only the detuning Δ(t)\Delta(t) of QD1, keeping all other Hamiltonian parameters fixed. Since the only time-dependent term in the Hamiltonian is Δ(t)n^1\Delta(t)\hat{n}_1, the instantaneous power supplied to the battery is

W˙sys(t)=Tr⁡[ρ^(t)H^˙(t)]=Δ˙(t)⟨n^1(t)⟩.(14)\dot{W}_{\mathrm{sys}}(t) = \operatorname{Tr}\left[\hat{\rho}(t)\dot{\hat{H}}(t)\right] = \dot{\Delta}(t)\langle\hat{n}_1(t)\rangle. \tag*{(14)}

The net work extracted over the complete cycle is therefore

Wext=−∫0tfdt Δ˙(t)⟨n^1(t)⟩=E(0)−E(tf),(15)W_{\mathrm{ext}} = -\int_{0}^{t_{\mathrm{f}}} \mathrm{d}t\,\dot{\Delta}(t)\langle\hat{n}_1(t)\rangle= E(0)-E(t_{\mathrm{f}}), \tag*{(15)}

where H^(tf)=H^(0)\hat{H}(t_{\mathrm{f}})=\hat{H}(0). Physically, the extracted work is associated with the electrostatic energy change induced by the plunger gate. Using Δ(t)=−eαVg(t)\Delta(t)=-e\alpha V_{\mathrm{g}}(t), where VgV_{\mathrm{g}} is the gate voltage and α\alpha is the capacitive lever arm defined in Appendix A, the work can equivalently be expressed as Wext=eα∫0tfdt Vg(t)⟨n^1(t)⟩W_{\mathrm{ext}}=e\alpha\int_{0}^{t_{\mathrm{f}}}\mathrm{d}t\,V_{\mathrm{g}}(t)\langle\hat{n}_1(t)\rangle.

A realization of this approach is shown in Figure 6 using a three-stage gate protocol. Starting from the charged steady state, the detuning is rapidly lowered in stage I, held near resonance during stage II to allow coherent population redistribution, and finally restored to its initial value in stage III. During the rapid downward ramp, the occupation of QD1 changes only weakly, allowing substantial work extraction. At the reduced detuning, coherent tunneling produces oscillations in the QD1 occupation, and the hold time is chosen near one of its minima. During the upward ramp, the occupation remains substantially below its initial value, so only a fraction of the extracted work is supplied back to the battery.

Cyclic unitary discharge protocol and energy and occupation dynamics

Figure 6. Cyclic unitary discharge by modulation of the QD1 gate voltage. (a) Detuning protocol, divided into three stages: (I) rapid reduction of Δ\Delta from 100Ω100\Omega to Δmin⁡=0.23Ω\Delta_{\min}=0.23\Omega, (II) coherent evolution at fixed Δmin⁡\Delta_{\min}, and (III) restoration of the initial detuning. (b) Internal energy EE, passive energy EpassiveE_{\mathrm{passive}}, and ergotropy W\mathcal{W} during the protocol. (c) Occupation of the detuned dot, ⟨n1⟩\langle n_1\rangle. The parameters are Ωτdown/ℏ=0.2\Omega\tau_{\mathrm{down}}/\hbar=0.2, Ωτhold/ℏ=29.5\Omega\tau_{\mathrm{hold}}/\hbar=29.5, and Ωτup/ℏ=25\Omega\tau_{\mathrm{up}}/\hbar=25. For visibility, the horizontal scale is independently rescaled within each of the three stages; time is linear within each stage, the tick labels give the physical values of Ωt/ℏ\Omega t/\hbar, and there is no time gap between the stages.

For the protocol shown in Figure 6, the charged state has initial energy E(0)≃27.79ΩE(0)\simeq27.79\Omega and ergotropy W(0)≃20.50ΩW(0)\simeq20.50\Omega. The gate cycle extracts Wext≃20.20ΩW_{\mathrm{ext}}\simeq20.20\Omega, corresponding to approximately 98.6% of the initial ergotropy. The parameters above were selected from a numerical search for a simple high-efficiency protocol, rather than from a strict global optimization. During the cycle, WW can exceed EE because the fixed energy reference is set by the ground state of the initial Hamiltonian, and the instantaneous passive energy can thus become negative as Δ\Delta is lowered. The coherent evolution during stage II produces multiple favorable transfer times, and further optimization can yield extraction even closer to the ergotropy bound.

Discharge into a Load

The unitary protocol above establishes that nearly all of the ergotropy stored during charging is accessible through coherent gate control. We now consider a complementary mesoscopic discharge protocol in which the stored energy is transferred directly to an electronic load, doing work by moving the electron against an electrical potential. After the battery has reached its charged nonequilibrium steady state, the dephasing source and the charging reservoir are switched off, and the detuned QD1 is coupled to a separate load reservoir. The load reservoir is characterized by a chemical potential μload\mu_{\mathrm{load}}, temperature TloadT_{\mathrm{load}}, and tunnel coupling Γload\Gamma_{\mathrm{load}}. Since the internal energy of the charged state is dominated by population in the detuned eigenstate ∣d⟩\lvert d\rangle, the load is coupled to QD1, as shown in Figure 7. The load chemical potential is chosen below the energy of this state,

Discharge protocol by coupling an electronic load

Figure 7. Discharge protocol by coupling an electronic load. After charging, the dephasing source and the original charging reservoir are decoupled, and the detuned QD1 is coupled to a load with tunnel coupling Γload\Gamma_{\mathrm{load}}. The load is characterized by temperature TloadT_{\mathrm{load}} and chemical potential μload\mu_{\mathrm{load}}. Since the charged state has large population in the detuned eigenstate ∣d⟩\lvert d\rangle, coupling the load to QD1 provides a direct extraction channel.

μload=Ed−4.5kBTload,(16)\mu_{\mathrm{load}}=E_d-4.5k_{\mathrm{B}}T_{\mathrm{load}}, \tag*{(16)}

so that tunneling mostly occurs from ∣d⟩\lvert d\rangle into the load. In the results below, we use kBTload=Ωk_{\mathrm{B}}T_{\mathrm{load}}=\Omega and Γload=0.1Ω\Gamma_{\mathrm{load}}=0.1\Omega. Later in this section, we examine the dependence of the extracted energy on μload\mu_{\mathrm{load}} and show that this choice lies close to the optimal value.

During discharge, the density matrix evolves according to the same global master-equation framework introduced in § 1 C, but with the charging-reservoir and dephasing terms removed:

dρ^dt=−iℏ[H^0,ρ^]+Lloadρ^.(17)\frac{d\hat{\rho}}{dt}=-\frac{i}{\hbar}[\hat{H}_0,\hat{\rho}]+\mathcal{L}_{\mathrm{load}}\hat{\rho}. \tag*{(17)}

Since the load is tunnel-coupled to QD1, its coupling to each single-electron eigenstate ∣a⟩\lvert a\rangle is weighted by ∣ua∣2\lvert u_a\rvert^2. The load Liouvillian is

Lloadρ^=1ℏ∑a(Wa0(load)D[∣a⟩⟨0∣]+W0a(load)D[∣0⟩⟨a∣])ρ^,(18)\mathcal{L}_{\mathrm{load}}\hat{\rho}=\frac{1}{\hbar}\sum_a\left(W_{a0}^{(\mathrm{load})}\mathcal{D}[\lvert a\rangle\langle0\rvert]+W_{0a}^{(\mathrm{load})}\mathcal{D}[\lvert0\rangle\langle a\rvert]\right)\hat{\rho}, \tag*{(18)}

where a∈{g,e,d}a\in\{g,e,d\}. The corresponding extraction and

injection rates are, respectively,

W0a(load)=Γload∣ua∣2[1−fload(Ea)],W_{0a}^{(\mathrm{load})}=\Gamma_{\mathrm{load}}\lvert u_a\rvert^2[1-f_{\mathrm{load}}(E_a)],
Wa0(load)=Γload∣ua∣2fload(Ea),(19)W_{a0}^{(\mathrm{load})}=\Gamma_{\mathrm{load}}\lvert u_a\rvert^2f_{\mathrm{load}}(E_a), \tag*{(19)}

where fload(E)=[1+exp⁡((E−μload)/kBTload)]−1f_{\mathrm{load}}(E)=[1+\exp((E-\mu_{\mathrm{load}})/k_{\mathrm{B}}T_{\mathrm{load}})]^{-1}. The first process removes an electron from eigenstate ∣a⟩\lvert a\rangle and transfers it to the load, whereas the second injects an electron from the load into the TQD.

Writing pa(t)=⟨a∣ρ^(t)∣a⟩p_a(t)=\langle a\vert\hat{\rho}(t)\vert a\rangle and p0(t)=⟨0∣ρ^(t)∣0⟩p_0(t)=\langle0\vert\hat{\rho}(t)\vert0\rangle, the net particle current into the load is

Iload(t)=1ℏ∑a[W0a(load)pa(t)−Wa0(load)p0(t)].(20)I_{\mathrm{load}}(t)=\frac{1}{\hbar}\sum_a\left[W_{0a}^{(\mathrm{load})}p_a(t)-W_{a0}^{(\mathrm{load})}p_0(t)\right]. \tag*{(20)}

The first contribution corresponds to electrons leaving the TQD and entering the load, while the second describes electrons injected back into the TQD. Positive IloadI_{\mathrm{load}} therefore denotes net electron transfer into the load. Each electron transferred into the load against the chemical-potential difference μload−μsource\mu_{\mathrm{load}}-\mu_{\mathrm{source}} contributes electrochemical work. The corresponding output power is therefore

Pload(t)=(μload−μsource)Iload(t),(21)P_{\mathrm{load}}(t)=(\mu_{\mathrm{load}}-\mu_{\mathrm{source}})I_{\mathrm{load}}(t), \tag*{(21)}

and the accumulated useful energy delivered to the load is

Wload(t)=∫0tPload(t′) dt′.(22)W_{\mathrm{load}}(t)=\int_0^t P_{\mathrm{load}}(t')\,dt'. \tag*{(22)}

Here WloadW_{\mathrm{load}} accounts only for the electrochemical energy stored against the load bias, rather than the total energy transferred from the TQD, part of which is dissipated as heat in the reservoir. Figure 8 shows the resulting discharge dynamics. Panel (a) gives the eigenstate populations. The population of the detuned state pdp_d is rapidly depleted, while the empty-state population p0p_0 increases. The population of the low-energy state ∣e⟩|e\rangle remains nearly unchanged, showing that the load predominantly removes the high-energy population generated during charging. This selectivity follows from the strong localization of ∣d⟩|d\rangle on QD1 and the much smaller QD1 overlap of the low-energy eigenstates.

Load-coupled discharge dynamics

Figure 8. Load-coupled discharge dynamics. The battery is initialized in the charged steady state, after which both the dephasing source and the charging reservoir are switched off, and the detuned dot is coupled to a load reservoir with Γload=0.1Ω\Gamma_{\mathrm{load}} = 0.1\Omega and μload=Ed−4.5kBTload\mu_{\mathrm{load}} = E_d - 4.5k_{\mathrm{B}}T_{\mathrm{load}}. (a) Eigenstate populations, showing rapid depletion of the detuned state pdp_d. (b) Normalized internal energy and ergotropy. (c) Integrated load output, normalized by E(0)E(0) and W(0)\mathcal{W}(0).

This results in the decay of the battery energy and ergotropy, as shown in Figure 8(b). The discharge is much faster than charging because the two processes involve different coupling mechanisms. Charging relies on dephasing-induced transitions into the detuned state, with rates of order γΩ2/(ℏΔ2)\gamma\Omega^2/(\hbar\Delta^2), giving τW∝ℏΔ2/(γΩ2)\tau_{\mathcal{W}} \propto\hbar\Delta^2/(\gamma\Omega^2). During discharge, the load is directly coupled to QD1, where the detuned state is predominantly localized. Its tunneling rate is therefore of order Γload/ℏ\Gamma_{\mathrm{load}}/\hbar, giving a characteristic discharge time τdis∼ℏ/Γload\tau_{\mathrm{dis}} \sim\hbar/\Gamma_{\mathrm{load}}. The internal energy saturates at a small nonzero value, reflecting the passive energy remaining in the final mixed state.

The accumulated useful output Wload(t)W_{\mathrm{load}}(t), normalized by both the initial internal energy E(0)E(0) and the initial ergotropy W(0)\mathcal{W}(0), is plotted in Figure 8(c). The normalization by E(0)E(0) gives the fraction of the initially stored energy converted into electrochemical energy in the load,

while normalization by W(0)\mathcal{W}(0) provides a comparison with the maximum work extractable through cyclic unitary operations. In contrast to the protocol of § 1.2 A, the load-coupled protocol is an open, nonunitary process and is therefore not subject to the ergotropy bound. Particle exchange with the load can also convert energy belonging to the passive component of the initial state, allowing WloadW_{\mathrm{load}} to exceed the initial ergotropy.

To examine the dependence of the discharge performance on the load bias, we calculate the accumulated output at the final discharge time, Wload(tf)W_{\mathrm{load}}(t_f), for different values of μload\mu_{\mathrm{load}} with Ωtf/ℏ=100\Omega t_f/\hbar= 100, as shown in Figure 9. The extracted energy exhibits a broad maximum around μload≃95.5Ω\mu_{\mathrm{load}} \simeq95.5\Omega. Increasing μload\mu_{\mathrm{load}} initially increases the electrochemical energy gained per transferred electron, whereas as μload\mu_{\mathrm{load}} approaches EdE_d, tunneling from the detuned state into the load becomes increasingly suppressed by the Fermi occupation of the load. The value μload=Ed−4.5kBTload\mu_{\mathrm{load}} = E_d - 4.5k_{\mathrm{B}}T_{\mathrm{load}} used above lies close to this maximum, with only a negligible reduction in the extracted energy. The broad maximum also shows that efficient discharge does not require fine tuning of the load chemical potential.

Dependence of the accumulated useful output on the load chemical potential

Figure 9. Dependence of the accumulated useful output on the load chemical potential. The output Wload(tf)W_{\mathrm{load}}(t_f) is evaluated at the end of the discharge protocol, Ωtf/ℏ=100\Omega t_f/\hbar= 100, with all other parameters as in Figure 8.

An important consideration for repeated operation is whether the state remaining after discharge significantly affects the subsequent charging dynamics. We therefore calculated the charging time (discussed in Sec. III B) using the discharged state as the initial condition. The time required to recover 95% of the steady-state ergotropy is ΩτW/ℏ≃2.62×104\Omega\tau_{\mathcal{W}}/\hbar\simeq2.62 \times10^4 (for the same parameters as in Figure 2), compared with ΩτW/ℏ≃2.64×104\Omega\tau_{\mathcal{W}}/\hbar\simeq2.64 \times10^4 when charging from equilibrium. Thus, recharging after discharge takes about the same time as charging the battery from equilibrium.

The extracted energy ultimately originates from the nonequilibrium dephasing source used during charging. The TQD therefore acts as an intermediate storage element: dephasing prepares an active population in the high-energy state, and the load subsequently extracts this stored energy through a separate discharge channel.

Conclusion

We have proposed a simple realization of an open quantum battery powered solely by local dephasing. The battery consists of a triple quantum dot coupled to a thermal reservoir, where a strongly detuned end dot acts as the high-energy storage element. Because the local dephasing operator does not commute with the system Hamiltonian, dephasing redistributes population among the energy eigenstates and autonomously drives the system into a highly active nonequilibrium steady state. The large detuning is essential in this architecture, as it creates a high-energy state that is weakly coupled to the reservoir, suppressing relaxation before the stored energy can be extracted.

The battery exhibits a large steady-state ergotropy, with an ergotropic efficiency approaching 1 in the limit kBT≪Ωk_{\mathrm{B}}T \ll\Omega. While the final stored energy depends primarily on the detuning of the storage dot, the charging time can be controlled through the dephasing strength, providing an experimentally accessible tuning parameter. Once charged, the dephasing source can be switched off while the stored energy remains trapped in a long-lived charged state because the high-energy state couples only weakly to the reservoir.

We have also demonstrated two complementary approaches to recovering the stored energy. The first uses a cyclic modulation of the detuned-dot gate to extract nearly all the available ergotropy, requiring no additional quantum system or complex control sequence. The second transfers energy directly to an electronic load through particle exchange, converting part of the battery’s passive energy into electrochemical work and thereby exceeding the work accessible through cyclic unitary operations on the battery alone. This output is robust over a range of load chemical potentials. Furthermore, the battery can be recharged after discharge on essentially the same timescale as the initial charging process, supporting its potential for repeated operation.

Our results establish local dephasing as an autonomous thermodynamic resource for charging open quantum batteries. More broadly, they demonstrate how the interplay of local dephasing and energy-selective transport can be harnessed to generate, store, and extract useful energy in experimentally accessible mesoscopic quantum-dot platforms.

An important direction for future work is scaling the proposed mechanism to larger energy-storage capacities. The present model operates in the strong Coulomb-blockade regime, where only one electron can occupy the TQD chain at a time. A direct scaling approach would be to operate multiple batteries in parallel, allowing the total stored energy to grow approximately linearly with the number of units. Alternatively, relaxing the single-electron restriction could allow several high-energy states to be occupied simultaneously within the chain. In this case, however, electron-electron interactions would modify the energy spectrum and could affect both the charging mechanism and the extractable work. Exploring such many-electron architectures would be a natural extension of the present work toward practical quantum batteries.

Acknowledgments

A.N.S. and A.N.J. acknowledge support from the John Templeton Foundation Grant ID 63209. R.S. acknowledges funding from the Spanish Ministerio de Ciencia e Innovación via grant No. PID2024-157821NB-I00, and through the “María de Maeztu” Programme for Units of Excellence in R&D CEX2023-001316-M.

Charging by Resistor Noise

In the main text, the charging mechanism is described broadly in terms of a local dephasing channel acting on the detuned barrier dot. One possible microscopic realization of this dephasing source is a nearby resistive element that produces Johnson–Nyquist voltage fluctuations [47]. These fluctuations shift the onsite energies of the capacitively coupled barrier dot and thereby generate charge dephasing. In this appendix, we show how this noisy-resistor configuration reduces to the dephasing term used in § 1 C.

We write the fluctuating voltage of the resistive element as δVres(t)\delta V_{\mathrm{res}}(t). Since the dots are capacitively coupled to this voltage source, the corresponding interaction Hamiltonian is

H^int(t)=δVres(t)A^res,A^res=∑j=13ηjn^j.(23)\hat{H}_{\mathrm{int}}(t)=\delta V_{\mathrm{res}}(t)\hat{A}_{\mathrm{res}},\qquad\hat{A}_{\mathrm{res}}=\sum_{j=1}^{3}\eta_j\hat{n}_j. \tag*{(23)}

Here n^j\hat{n}_j is the occupation operator of dot jj, and ηj\eta_j is the electrostatic coupling that converts a voltage fluctuation into an energy shift of dot jj. In a simple lever-arm description, ηj≃αj\eta_j \simeq\alpha_j, with αj≃Cjres/CΣj\alpha_j \simeq C_{j\mathrm{res}}/C_{\Sigma j}, where CjresC_{j\mathrm{res}} is the capacitance between dot jj and the noisy resistive element, and CΣjC_{\Sigma j} is the total capacitance of dot jj [48, 49].

In order for the noisy environment to be represented by the same time-local Lindblad formalism used in the main text, its correlation time must be short compared with the intrinsic timescales of the dot dynamics [50]. Otherwise, the system evolution would depend on the earlier history of the voltage fluctuations, and the reduced dynamics would require a non-Markovian description. The Markovian limit is therefore obtained when the voltage noise is effectively white over the transition frequencies relevant to the dot system. With the two-sided angular-frequency convention,

SV(ω)=∫−∞∞dτ eiωτ⟨δVres(τ)δVres(0)⟩.(24)S_V(\omega)=\int_{-\infty}^{\infty}\mathrm{d}\tau\,e^{i\omega\tau}\langle\delta V_{\mathrm{res}}(\tau)\delta V_{\mathrm{res}}(0)\rangle. \tag*{(24)}

If SV(ω)≃SVS_V(\omega)\simeq S_V is approximately constant over the relevant frequency window, then

⟨δVres(t)δVres(t′)⟩=SVδ(t−t′).(25)\langle\delta V_{\mathrm{res}}(t)\delta V_{\mathrm{res}}(t')\rangle=S_V\delta(t-t'). \tag*{(25)}

This delta-correlated form shows that the voltage noise is memoryless on the timescales resolved by the quantum-dot dynamics.

For an impedance Zres(ω)Z_{\mathrm{res}}(\omega), the quantum Johnson–Nyquist spectrum [51, 52] is

SV(ω)=2ℏωRe⁡Zres(ω)1−exp⁡[−ℏω/(kBTres)].(26)S_V(\omega)=\frac{2\hbar\omega\operatorname{Re}Z_{\mathrm{res}}(\omega)}{1-\exp[-\hbar\omega/(k_{\mathrm{B}}T_{\mathrm{res}})]}. \tag*{(26)}

where TresT_{\mathrm{res}} is the resistor temperature. The white-noise limit follows from two approximations. First, the resistor temperature must be large compared with the relevant transition energies, kBTres≫ℏ∣ω∣k_{\mathrm{B}}T_{\mathrm{res}}\gg\hbar\lvert\omega\rvert, so that the quantum spectrum becomes classical. In this limit, SV(ω)≃2kBTresRe⁡Zres(ω)S_V(\omega)\simeq2k_{\mathrm{B}}T_{\mathrm{res}}\operatorname{Re}Z_{\mathrm{res}}(\omega). Second, the electromagnetic environment must be approximately Ohmic over the same frequency window, Re⁡Zres(ω)≃Rres\operatorname{Re}Z_{\mathrm{res}}(\omega)\simeq R_{\mathrm{res}}. Together these assumptions give the frequency-independent spectrum

SV(ω)≃SV=2kBTresRres.(27)S_V(\omega)\simeq S_V=2k_{\mathrm{B}}T_{\mathrm{res}}R_{\mathrm{res}}. \tag*{(27)}

Averaging over the classical white voltage noise gives

dρ^dt=−iℏ[H^,ρ^]−SV2ℏ2[A^res,[A^res,ρ^]].(28)\frac{d\hat{\rho}}{dt}=-\frac{i}{\hbar}[\hat{H},\hat{\rho}]-\frac{S_V}{2\hbar^2}[\hat{A}_{\mathrm{res}},[\hat{A}_{\mathrm{res}},\hat{\rho}]]. \tag*{(28)}

Since A^res\hat{A}_{\mathrm{res}} is Hermitian, D[A^res]ρ^=−[A^res,[A^res,ρ^]]/2\mathcal{D}[\hat{A}_{\mathrm{res}}]\hat{\rho}=-[\hat{A}_{\mathrm{res}},[\hat{A}_{\mathrm{res}},\hat{\rho}]]/2, and therefore

dρ^dt=−iℏ[H^,ρ^]+SVℏ2D[A^res]ρ^.(29)\frac{d\hat{\rho}}{dt}=-\frac{i}{\hbar}[\hat{H},\hat{\rho}]+\frac{S_V}{\hbar^2}\mathcal{D}[\hat{A}_{\mathrm{res}}]\hat{\rho}. \tag*{(29)}

This has the same Lindblad structure as the local dephasing term in Eq. (6). Defining

L^res=SVℏA^res=∑j=13ηjSVℏn^j,(30)\hat{L}_{\mathrm{res}}=\sqrt{\frac{S_V}{\hbar}}\hat{A}_{\mathrm{res}}=\sum_{j=1}^{3}\eta_j\sqrt{\frac{S_V}{\hbar}}\hat{n}_j, \tag*{(30)}

the noisy-resistor contribution can be written as Lresρ^=ℏ−1D[L^res]ρ^\mathcal{L}_{\mathrm{res}}\hat{\rho}=\hbar^{-1}\mathcal{D}[\hat{L}_{\mathrm{res}}]\hat{\rho}, consistent with the energy-unit convention of the main text. Thus, the effective local dephasing parameters are

γj(res)=ηj2SVℏ.(31)\gamma_j^{(\mathrm{res})}=\frac{\eta_j^2S_V}{\hbar}. \tag*{(31)}

Using Eq. (27), this becomes γj(res)=2ηj2kBTresRres/ℏ\gamma_j^{(\mathrm{res})}=2\eta_j^2k_{\mathrm{B}}T_{\mathrm{res}}R_{\mathrm{res}}/\hbar. For ηj=eαj\eta_j=e\alpha_j, one obtains γj(res)=2e2αj2kBTresRres/ℏ\gamma_j^{(\mathrm{res})}=2e^2\alpha_j^2k_{\mathrm{B}}T_{\mathrm{res}}R_{\mathrm{res}}/\hbar. For the charging configuration used in the main text, the dominant capacitive coupling is to QD1, so that γ1(res)=γ\gamma_1^{(\mathrm{res})}=\gamma and the remaining dephasing parameters are negligible.

In this realization, the thermodynamic resource is the noisy electromagnetic environment. The resistor supplies voltage fluctuations that dephase the quantum-dot charge states and drive transitions in the energy eigenbasis whenever the dephasing operator does not commute with the TQD Hamiltonian. The white-noise limit used above requires the resistor spectrum to be approximately flat over the relevant transition frequencies. In the present high-detuning regime this requires, in particular, kBTres≫Δk_{\mathrm{B}}T_{\mathrm{res}}\gg\Delta. Since the electronic reservoir temperature used in the main text satisfies kBT=Ωk_{\mathrm{B}}T=\Omega with Δ=100Ω\Delta=100\Omega, this corresponds to a resistor temperature much larger than the electronic reservoir temperature. The charging process is therefore powered by an additional hot environment and does not violate the second law.

It is useful to estimate the resistor temperature required to realize the dephasing strengths used in the main text. From Eq. (31), the condition γj(res)∼10Ω\gamma_j^{(\mathrm{res})}\sim10\Omega gives

Tres∼5ℏΩe2αj2kBRres.(32)T_{\mathrm{res}}\sim\frac{5\hbar\Omega}{e^2\alpha_j^2k_{\mathrm{B}}R_{\mathrm{res}}}. \tag*{(32)}

Taking Rres=RK=h/e2R_{\mathrm{res}}=R_K=h/e^2 gives the optimistic mesoscopic high-impedance estimate

Tres∼5Ω2παj2kB.(33)T_{\mathrm{res}}\sim\frac{5\Omega}{2\pi\alpha_j^2k_{\mathrm{B}}}. \tag*{(33)}

For the scale Ω=1 μeV\Omega=1\,\mu\mathrm{eV} and γ=10Ω\gamma=10\Omega, this gives Tres∼92 KT_{\mathrm{res}}\sim92\,\mathrm{K} for αj=0.01\alpha_j=0.01, Tres∼10 KT_{\mathrm{res}}\sim10\,\mathrm{K} for αj=0.03\alpha_j=0.03, and Tres∼0.9 KT_{\mathrm{res}}\sim0.9\,\mathrm{K} for αj=0.1\alpha_j=0.1. These estimates scale inversely with both RresR_{\mathrm{res}} and αj2\alpha_j^2. Thus, if the relevant environmental impedance were a conventional 50 Ohm line rather than a high-impedance mesoscopic environment, the required temperatures would be larger by RK/(50 Ohm)≃5×102R_K/(50\,\mathrm{Ohm})\simeq5\times10^2. In addition, realizing the classical white-noise limit over the detuning scale requires kBTres≫Δk_{\mathrm{B}}T_{\mathrm{res}}\gg\Delta. For the parameters used in the main text, Δ=100Ω\Delta=100\Omega, so Δ/kB≃1.2 K\Delta/k_{\mathrm{B}}\simeq1.2\,\mathrm{K} when Ω=1 μeV\Omega=1\,\mu\mathrm{eV}. A lever arm of approximately αj=0.03\alpha_j=0.03 and Rres=50 OhmR_{\mathrm{res}}=50\,\mathrm{Ohm} therefore provides a more moderate temperature estimate while keeping the resistor temperature substantially above the detuning energy scale.

Charging by Continuous Measurement

A second microscopic realization of the dephasing source is continuous charge measurement with a nearby quantum point contact (QPC) [34]. In this case, the QPC current depends weakly on the charge occupation of the nearby dots. Information about the dot charge is therefore continuously acquired by the detector, and the corresponding measurement backaction produces dephasing in the quantum-dot system. In this appendix, we show how the ensemble-averaged dynamics reduce to the same local dephasing channel used in the main text.

Let the QPC be capacitively coupled to the charge configuration of the TQD through the operator

A^QPC=∑j=13λjn^j(34)\hat{A}_{\mathrm{QPC}}=\sum_{j=1}^{3}\lambda_j\hat{n}_j \tag*{(34)}

where λj\lambda_j describes how sensitively the QPC responds to occupation of dot jj [15]. The resulting dephasing depends on both these coupling coefficients and the detector noise. For the charging configuration considered in the main text, the detector is positioned so that its dominant charge sensitivity is to the detuned QD1, while its coupling to QDs 2 and 3 is negligible.

For a weak continuous measurement, the conditional state of the TQD evolves stochastically because the measurement record is noisy [53]. However, when one averages over all possible measurement records, the unconditional density matrix obeys a deterministic master equation. The measurement contribution has the Lindblad form

dρ^dt∣QPC=LQPCρ^=1ℏD[L^QPC]ρ^,(35)\left.\frac{d\hat{\rho}}{dt}\right|_{\mathrm{QPC}}=\mathcal{L}_{\mathrm{QPC}}\hat{\rho}=\frac{1}{\hbar}\mathcal{D}[\hat{L}_{\mathrm{QPC}}]\hat{\rho}, \tag*{(35)}

with

L^QPC=∑j=13γj(QPC)n^j.(36)\hat{L}_{\mathrm{QPC}}=\sum_{j=1}^{3}\sqrt{\gamma_j^{(\mathrm{QPC})}}\hat{n}_j. \tag*{(36)}

Here γj(QPC)\gamma_j^{(\mathrm{QPC})} is the measurement-induced dephasing parameter expressed in energy units, consistent with the convention adopted in the main text. The corresponding dephasing rates are proportional to γj(QPC)/ℏ\gamma_j^{(\mathrm{QPC})}/\hbar and are determined by the detector response and shot noise.

For example, in a linearly responding QPC, the measurement rate is proportional to the square of the difference between the detector currents associated with different charge states, divided by the detector noise power SIS_I [53]. For an ideal detector, a commonly used expression for the corresponding measurement-induced energy scale is

γj(QPC)=ℏ(I0−Ij)24SI=eV4π(T0−Tj)2T(1−T),(37)\gamma_j^{(\mathrm{QPC})}=\frac{\hbar(I_0-I_j)^2}{4S_I}=\frac{eV}{4\pi}\frac{(T_0-T_j)^2}{T(1-T)}, \tag*{(37)}

where T0T_0 (TjT_j) is the transmission coefficient of the QPC when QDjj is empty (filled), T=(T0+Tj)/2T=(T_0+T_j)/2, and VV is the voltage bias across the QPC. The precise relationship between measurement and dephasing rates depends on the detector operating regime and noise convention. The Markovian description further assumes that the detector noise spectrum is sufficiently broad over the relevant TQD transition frequencies.

In the configuration used in the main text, the detector is sensitive predominantly to QD1. The ensemble-averaged measurement contribution then has the Lindblad form (B2) with

L^QPC=γn^1.(38)\hat{L}_{\mathrm{QPC}}=\sqrt{\gamma}\hat{n}_1. \tag*{(38)}

It suppresses coherences between states with different barrier-dot occupation, while leaving the total particle number unchanged.

The continuous-measurement realization has a different thermodynamic interpretation from the noisy-resistor realization discussed in Appendix A. Here the thermodynamic resource is the biased detector. The QPC is driven out of equilibrium by the applied voltage bias, and the resulting measurement backaction produces the dephasing channel acting on the TQD. The detector record could in principle be used to define conditional trajectories, but the main text only uses the ensemble-averaged dynamics. Therefore, the charging mechanism does not rely on feedback, postselection, or measurement-conditioned work extraction; it relies only on the unconditional dephasing generated by the detector.

Other Dephasing Configurations

In the main text, we focus on dephasing of the detuned QD1. This choice acts directly on the dot that dominates the high-energy storage state ∣d⟩\lvert d\rangle and provides the minimal implementation of dephasing-induced charging. Here we compare this configuration with dephasing applied separately to each of the other two dots in the TQD.

For a dephased dot jj, we use the local operator

L^j=γn^j.(39)\hat{L}_j=\sqrt{\gamma}\hat{n}_j. \tag*{(39)}

We compare dephasing of QD1, QD2, and QD3 at the same dephasing strength γ\gamma, together with the evolution in the absence of dephasing.

Figure 10 shows that the location of the dephasing is crucial not only for the amount of energy deposited in the TQD but also for whether that energy is useful. Dephasing QD1 produces both the largest stored energy and a strongly non-passive steady state, with an ergotropic efficiency approaching the value discussed in the main text. Dephasing QD2 can also inject a substantial amount of energy, but the resulting state is almost passive and therefore has only a small ergotropic fraction. By contrast, dephasing QD3, which is directly connected to the reservoir side of the TQD, produces very little charging and essentially no steady-state ergotropy.

Charging dynamics for different local dephasing configurations

Figure 10. Charging dynamics for different local dephasing configurations. Dephasing is applied individually to QD1, QD2, or QD3 with the same strength γ\gamma. (a) Internal energy E(t)/ΩE(t)/\Omega. (b) Ergotropic efficiency W(t)/E(t)W(t)/E(t). Dephasing of the detuned storage dot QD1 produces both large stored energy and high ergotropic efficiency. Dephasing of QD2 also substantially increases the internal energy but produces little ergotropy, whereas dephasing of the reservoir-coupled QD3 results in negligible charging. The evolution without dephasing is shown for comparison. Parameters are the same as in Figure 2.

These results demonstrate that energy injection alone is not sufficient for battery charging in the thermodynamic sense. Useful charging requires the dephasing-induced redistribution to create a non-passive population ordering. Acting directly on the detuned storage dot accomplishes both tasks simultaneously: it efficiently populates the high-energy state ∣d⟩\lvert d\rangle while the distant reservoir preferentially equilibrates the low-energy sector. This makes QD1 dephasing the natural and minimal choice for the protocol studied in the main text.

Higher-Electron Sector

The main text uses the strong-Coulomb-blockade description in which the accessible Hilbert space consists of the empty state and the single-electron eigenstates of the triple-dot Hamiltonian. This approximation assumes that higher-charge sectors remain energetically inaccessible through particle injection from the reservoir. However, dephasing can populate the strongly detuned state even when its energy is Δ=100Ω\Delta= 100\Omega. Since realistic charging energies can be comparable to the detuning, it is necessary to check whether the same dephasing-induced redistribution could indirectly lead to appreciable occupation of higher-charge sectors. We therefore extend the model to include all two-electron states and explicitly test whether they become populated.

For this purpose, we use a spinful extended-Hubbard Hamiltonian for the three-dot array, including onsite and distance-dependent interdot Coulomb interactions [34, 54],

H^ext=∑i,σϵin^iσ−Ω∑i=12∑σ(c^iσ†c^i+1,σ+c^i+1,σ†c^iσ)+U∑i=13n^i↑n^i↓+12∑i≠jV∣i−j∣n^in^j,(40)\hat{H}_{\mathrm{ext}} = \sum_{i,\sigma} \epsilon_i \hat{n}_{i\sigma} - \Omega\sum_{i=1}^{2} \sum_{\sigma} \left(\hat{c}_{i\sigma}^{\dagger}\hat{c}_{i+1,\sigma} + \hat{c}_{i+1,\sigma}^{\dagger}\hat{c}_{i\sigma}\right) + U \sum_{i=1}^{3} \hat{n}_{i\uparrow}\hat{n}_{i\downarrow} + \frac{1}{2}\sum_{i\ne j} V_{\lvert i-j\rvert}\hat{n}_i\hat{n}_j, \tag*{(40)}

where

n^i=n^i↑+n^i↓.(41)\hat{n}_i = \hat{n}_{i\uparrow} + \hat{n}_{i\downarrow}. \tag*{(41)}

The barrier dot is detuned by setting ϵ1=Δ\epsilon_1 = \Delta, ϵ2=ϵ3=0\epsilon_2 = \epsilon_3 = 0. The onsite charging energy is chosen to be the largest interaction scale, U=3ΔU = 3\Delta, while the offsite Coulomb interactions are taken to decrease with dot separation according to

V1=Δ,V2=0.8Δ.(42)V_1 = \Delta,\qquad V_2 = 0.8\Delta. \tag*{(42)}

The chosen hierarchy, U>V1>V2U > V_1 > V_2, reflects the reduction of electrostatic interaction with dot separation, while the specific ratios are selected as a conservative test rather than as a fit to a particular device [55, 56]. Here we use comparatively small interaction energies, of order the detuning, to provide a stringent test of whether multi-electron charging can occur. Larger charging energies would further suppress occupation of higher-particle-number sectors. These values still represent a strongly interacting regime within the dimensionless model: the mutual charging energies are comparable to the barrier detuning and are much larger than the coherent tunneling, reservoir coupling, and thermal energy scales used in the main text. With Δ=100Ω\Delta= 100\Omega, Γ=0.1Ω\Gamma= 0.1\Omega, kBT=Ωk_{\mathrm{B}}T = \Omega, and μ=ϵ=0\mu= \epsilon= 0 in the energy convention adopted here, injecting a second electron is energetically costly even though the charging energies are of the same order as the detuned barrier energy.

The many-body Hamiltonian in Eq. (40) conserves particle number. We diagonalize it in the truncated Fock space containing all states with N=0,1,2N = 0,1,2. For three spinful dots, this gives (60)+(61)+(62)=22\binom{6}{0}+\binom{6}{1}+\binom{6}{2}=22 many-body basis states. This truncation directly tests the first leakage channel beyond the single-electron model: if the N=2N=2 sector remains negligible, then higher-charge sectors, which require additional positive charging energies from UU and V∣i−j∣V_{\lvert i-j\rvert}, are expected to be even more strongly suppressed. Thus, the N≤2N \le2 calculation provides a conservative check of the strong-Coulomb-blockade approximation while explicitly allowing all two-electron spin and charge configurations.

The reduced density matrix is evolved in the many-body energy eigenbasis using the same global-master-equation structure as in § 1 C. The reservoir term allows transitions between states whose particle numbers differ by one, with injection and extraction rates determined by the Fermi functions of the reservoirs. The dephasing is included as an exact Lindblad term with Hermitian jump operators proportional to the dot occupations,

L^j=γjn^j.(43)\hat{L}_j=\sqrt{\gamma_j}\hat{n}_j . \tag*{(43)}

For the configuration used in the main text,

γ1=10Ω,γ2=γ3=0.(44)\gamma_1=10\Omega,\qquad\gamma_2=\gamma_3=0 . \tag*{(44)}

Importantly, dephasing does not itself inject particles into the dot array. Since n^j\hat{n}_j commutes with the total number operator N^\hat{N}, the dephasing-induced Lindblad term redistributes population and coherences within a fixed charge sector but does not change NN. Changes in the total charge can only occur through the reservoir jump processes. Therefore, occupation of the two-electron subspace remains controlled by the reservoir chemical potential and by the charging-energy cost of adding an electron.

Figure 11 shows the robustness of the two-electron suppression against reservoir parameters. We vary the reservoir chemical potential and temperature over μ/Ω∈[−0.5,0.5]\mu/\Omega\in[-0.5,0.5] and kBT/Ω∈[0.1,5]k_{\mathrm{B}}T/\Omega\in[0.1,5], while keeping the remaining parameters fixed at the values used in the main text. Throughout this entire parameter window, the two-electron probability remains of order 10−610^{-6}–10−510^{-5}, demonstrating that the higher-charge sector is strongly suppressed even when the reservoir temperature is increased to several times the hopping energy.

Figure 11. Robustness of the single-electron charging mechanism against two-electron leakage. The calculation includes all N=0,1,2N=0,1,2 many-body states of the spinful extended-Hubbard Hamiltonian in Eq. (40), with Δ=100Ω\Delta=100\Omega, U=3ΔU=3\Delta, V1=ΔV_1=\Delta, V2=0.8ΔV_2=0.8\Delta, and Γ=0.1Ω\Gamma=0.1\Omega. The plot shows the steady-state probability of occupying the two-electron sector, P(N=2)P(N=2), over the reservoir parameter window μ/Ω∈[−0.5,0.5]\mu/\Omega\in[-0.5,0.5] and kBT/Ω∈[0.1,5]k_{\mathrm{B}}T/\Omega\in[0.1,5]. The probability remains of order 10−610^{-6}–10−510^{-5}, showing that the two-electron sector is strongly suppressed throughout the parameter range considered.

This result supports the interpretation used in the main text. The dephasing enhances the occupation of the detuned single-electron state and thereby charges the battery, but it does not populate additional electrons by itself. Since the reservoir remains near μ=0\mu=0 and the two-electron configurations carry large charging penalties, injecting a second electron is energetically unfavorable. The small value of P(N=2)P(N=2) in Figure 11 shows that the dephasing-powered charging mechanism is not a consequence of higher-charge leakage. Rather, it is a redistribution mechanism operating predominantly within the empty and single-electron sectors.

Phonon-Induced Relaxation

To assess the influence of phonon-assisted relaxation on the battery stability, we supplement the master equation with a phenomenological dissipator describing transitions between the high-energy storage state ∣d⟩\lvert d\rangle and the two low-energy eigenstates ∣g⟩\lvert g\rangle and ∣e⟩\lvert e\rangle. The additional contribution is

Lphρ^=∑a=g,e[κa↓ℏD[∣a⟩⟨d∣]ρ^+κa↑ℏD[∣d⟩⟨a∣]ρ^],(45)\mathcal{L}_{\mathrm{ph}}\hat{\rho}=\sum_{a=g,e}\left[\frac{\kappa_a^\downarrow}{\hbar}\mathcal{D}[\lvert a\rangle\langle d\rvert]\hat{\rho}+\frac{\kappa_a^\uparrow}{\hbar}\mathcal{D}[\lvert d\rangle\langle a\rvert]\hat{\rho}\right], \tag*{(45)}

where D[L^]ρ^=L^ρ^L^†−12{L^†L^,ρ^}\mathcal{D}[\hat{L}]\hat{\rho}=\hat{L}\hat{\rho}\hat{L}^{\dagger}-\frac{1}{2}\{\hat{L}^{\dagger}\hat{L},\hat{\rho}\}. The downward and upward transition coefficients, expressed in energy units, are

κa↓=κph2[nB(Ed−Ea)+1],(46)\kappa_a^\downarrow=\frac{\kappa_{\mathrm{ph}}}{2}\left[n_{\mathrm{B}}(E_d-E_a)+1\right], \tag*{(46)}
κa↑=κph2nB(Ed−Ea),\kappa_a^\uparrow=\frac{\kappa_{\mathrm{ph}}}{2}n_{\mathrm{B}}(E_d-E_a),

with

nB(E)=1eE/(kBTph)−1.(47)n_{\mathrm{B}}(E)=\frac{1}{e^{E/(k_{\mathrm{B}}T_{\mathrm{ph}})}-1}. \tag*{(47)}

Here, κph/ℏ\kappa_{\mathrm{ph}}/\hbar denotes the total spontaneous emission rate from ∣d⟩\lvert d\rangle, distributed equally between the two low-energy states. The phonon bath temperature is taken to be kBTph=Ωk_{\mathrm{B}}T_{\mathrm{ph}}=\Omega, matching the electronic reservoir temperature.

The upward and downward transition rates satisfy detailed balance,

κa↑κa↓=e−(Ed−Ea)/(kBTph).(48)\frac{\kappa_a^\uparrow}{\kappa_a^\downarrow}=e^{-(E_d-E_a)/(k_{\mathrm{B}}T_{\mathrm{ph}})}. \tag*{(48)}

For Δ≫Ω\Delta\gg\Omega and kBTph=Ωk_{\mathrm{B}}T_{\mathrm{ph}}=\Omega, phonon absorption into the high-energy state is exponentially suppressed, while spontaneous emission remains possible.

The phonon dissipator is included throughout the charging and storage stages. For each value of κph\kappa_{\mathrm{ph}}, the battery is charged under the combined action of the electronic reservoir, local dephasing, and phonon relaxation until its ergodropy reaches 95% of the corresponding steady-state value. The dephasing source is then switched off, while the reservoir and phonon couplings remain unchanged. The resulting evolution is used to evaluate the ergotropy retention shown in Figure 5(b).

The phonon-induced transition rates are treated phenomenologically rather than derived from a microscopic electron–phonon Hamiltonian. In a specific device, the corresponding rates depend on the electron–phonon coupling matrix elements, phonon spectral density, and electronic wavefunctions. The calculations therefore characterize the sensitivity of the battery stability to additional inelastic relaxation, rather than predicting the storage lifetime of a particular semiconductor implementation.

Coherent Discharge Protocol

As an alternative discharge mechanism, we consider a protocol in which QD1 is capacitively coupled to an auxiliary double quantum dot (DQD), as illustrated in Figure 12. We denote the two auxiliary dots by AA and BB, with interdot hopping amplitude Ω′\Omega'. The state basis is augmented by including the occupation of the two subarrays: ∣Aj⟩\lvert A_j\rangle and ∣Bj⟩\lvert B_j\rangle if the electrons occupy quantum dots AA or BB in the auxiliary array, and jj in the battery. The capacitive coupling between QD1 and BB ensures that simultaneous occupation of these dots carries an additional interaction energy UU. The auxiliary levels are detuned according to EA−EB=E2−E1=−ΔE_A-E_B=E_2-E_1=-\Delta, which we parametrize as EA=ε′E_A=\varepsilon' and EB=ε′+ΔE_B=\varepsilon'+\Delta.

Schematic of the detuned dot of the TQD battery coupled to an auxiliary double quantum dot

Figure 12. The detuned dot of the TQD battery is capacitively coupled to an auxiliary double quantum dot, enabling coherent transfer of the stored excitation to the auxiliary system.

The auxiliary DQD remains empty during charging of the TQD. Once the battery has been charged, an electron is loaded into dot AA from an attached reservoir, preparing the initial state ∣A1⟩\lvert A1\rangle. At this stage it is convenient to detune the energies of QDs 2 and 3, E3−E2=δE_3-E_2=\delta, so they become effectively disconnected from the dynamics. Energy stored in QD1 can then be coherently transferred to the auxiliary DQD through the cotunneling process

∣A1⟩→∣X⟩→∣B2⟩(49)\lvert A1\rangle\to\lvert X\rangle\to\lvert B2\rangle \tag*{(49)}

The intermediate configurations X=A2X=A2 or X=B1X=B1 are off resonant and therefore only virtually occupied. The resulting effective coupling between the initial and final configurations is

H^eff=−ΩΩ′UΔ(Δ+U)∣A1⟩⟨B2∣+h.c.(50)\hat{H}_{\mathrm{eff}}=-\frac{\Omega\Omega' U}{\Delta(\Delta+U)}\lvert A1\rangle\langle B2\rvert+\mathrm{h.c.} \tag*{(50)}

Thus, the effective coupling, geff=ΩΩ′UΔ(Δ+U)g_{\mathrm{eff}}=\frac{\Omega\Omega' U}{\Delta(\Delta+U)}, enables coherent Rabi oscillations. After half a Rabi period, tg=πℏ/2gefft_g=\pi\hbar/2g_{\mathrm{eff}}, the electron initially occupying QD1 is transferred to QD2, while the electron in the auxiliary DQD is promoted to the higher energy state in AA. The energy released by the TQD is thereby transferred to the auxiliary system.

At this time tgt_g, the two systems must be brought out of resonance to prevent the reverse process. This can be achieved by sweeping the auxiliary levels through a Landau–Zener transition, transferring the electron between the auxiliary dots, followed by a rapid change of the energy of the empty dot BB. The final level configuration is chosen such that EA−EB≠E2−E1E_A-E_B\ne E_2-E_1, this way suppressing further resonant cotunneling between the TQD and the auxiliary DQD. The energies of dots 2 and 3 are then restored to ε\varepsilon. The protocol therefore provides a concrete route for coherently transferring the energy stored in the barrier dot to an auxiliary quantum system while leaving the TQD in a lower-energy configuration.

References

  1. [1]F. Campaioli, S. Gherardini, J. Q. Quach, M. Polini, and G. M. Andolina, Colloquium: Quantum batteries, Rev. Mod. Phys. 96, 031001 (2024).
  2. [2]R. Alicki and M. Fannes, Entanglement boost for extractable work from ensembles of quantum batteries, Phys. Rev. E 87, 042123 (2013).pubmed.ncbi.nlm.nih.gov/23679388
  3. [3]F. C. Binder, S. Vinjanampathy, K. Modi, and J. Goold, Quantacell: powerful charging of quantum batteries, New J. Phys. 17, 075015 (2015).DOI
  4. [4]F. Campaioli, F. A. Pollock, F. C. Binder, L. Céleri, J. Goold, S. Vinjanampathy, and K. Modi, Enhancing the Charging Power of Quantum Batteries, Phys. Rev. Lett. 118, 150601 (2017).DOI
  5. [5]D. Ferraro, M. Campisi, G. M. Andolina, V. Pellegrini, and M. Polini, High-Power Collective Charging of a Solid-State Quantum Battery, Phys. Rev. Lett. 120, 117702 (2018).DOI
  6. [6]A. E. Allahverdyan, R. Balian, and Th. M. Nieuwenhuizen, Maximal work extraction from finite quantum systems, Europhys. Lett. 67, 565 (2004).DOI
  7. [7]G. M. Andolina, M. Keck, A. Mari, M. Campisi, V. Giovannetti, and M. Polini, Extractable work, the role of correlations, and asymptotic freedom in quantum batteries, Phys. Rev. Lett. 122, 047702 (2019).DOI
  8. [8]D. Rossini, G. M. Andolina, and M. Polini, Many-body localized quantum batteries, Phys. Rev. B 100, 115142 (2019).DOI
  9. [9]K. V. Hovhannisyan, F. Barra, and A. Imparato, Charg- ing assisted by thermalization, Phys. Rev. Res. 2, 033413 (2020).
  10. [10]K. Xu, H.-J. Zhu, G.-F. Zhang, and W.-M. Liu, Enhancing the performance of an open quantum battery via environment engineering, Phys. Rev. E 104, 064143 (2021).DOI
  11. [11]A. C. Santos, B. i. e. i. f. m. c. Çakmak, S. Campbell, and N. Z. Zimmer, Stable adiabatic quantum batteries, Phys. Rev. E 100, 032107 (2019).DOI
  12. [12]S. Gherardini, F. Campaioli, F. Caruso, and F. C. Binder, Stabilizing open quantum batteries by sequential measurements, Phys. Rev. Res. 2, 013095 (2020).DOI
  13. [13]F. Barra, Dissipative charging of a quantum battery, Phys. Rev. Lett. 122, 210601 (2019).DOI
  14. [14]A. N. Singh, B. Bhandari, R. Sánchez, and A. N. Jordan, Capturing an electron in the virtual state, New J. Phys. 28, 074503 (2026).DOI
  15. [15]A. N. Singh, R. Sánchez, and A. N. Jordan, Collective charge measurement in quantum dot chains: controlling barrier occupation and tunneling current, arXiv:2605.19001 (2026).arxiv.org/abs/2605.19001
  16. [16]F. Mayo and A. J. Roncaglia, Collective effects and quantum coherence in dissipative charging of quantum batteries, Phys. Rev. A 105, 062203 (2022).DOI
  17. [17]R. Shastri, C. Jiang, G.-H. Xu, B. Prasanna Venkatesh, and G. Watanabe, Dephasing enabled fast charging of quantum batteries, npj Quantum Inf. 11, 9 (2025).DOI
  18. [18]B. Ahmadi et al., Harnessing environmental noise for quantum energy storage, arXiv:2510.06384 (2025).arxiv.org/abs/2510.06384
  19. [19]S.-Q. Liu, L. Wang, H. Fan, F.-L. Wu, and S.-Y. Liu, Charging Quantum Batteries with Noise, Adv. Quantum Technol. 8, e00504 (2025).DOI
  20. [20]M. M. Fajar, B. N. Pratiwi, S. Pramono, G. K. Sunnardianto, and A. R. Nugraha, Noise-induced Zeno-like effect in a spin-chain quantum battery, arXiv:2509.01603 (2025).arxiv.org/abs/2509.01603
  21. [21]F. T. Tabesh, F. H. Kamin, and S. Salimi, Environment-mediated charging process of quantum batteries, Phys. Rev. A 102, 052223 (2020).DOI
  22. [22]F. Tacchino, T. F. F. Santos, D. Gerace, M. Campisi, and M. F. Santos, Charging a quantum battery via nonequilibrium heat current, Phys. Rev. E 102, 062133 (2020).
  23. [23]F. H. Kamin, Z. Abuali, H. Ness, and S. Salimi, Quantum battery charging by non-equilibrium steady-state currents, J. Phys. A: Math. Theor. 56, 275302 (2023).DOI
  24. [24]C. Elouard, D. Herrera-Martí, B. Huard, and A. Auffeves, Extracting work from quantum measurement in Maxwell’s demon engines, Phys. Rev. Lett. 118, 260603 (2017).DOI
  25. [25]L. Buffoni, A. Solfanelli, P. Verrucchi, A. Cuccoli, and M. Campisi, Quantum measurement cooling, Phys. Rev. Lett. 122, 070603 (2019).DOI
  26. [26]J. Yi, P. Talkner, and Y. W. Kim, Single-temperature quantum engine without feedback control, Phys. Rev. E 96, 022108 (2017).DOI
  27. [27]J. Ferreira, T. Jin, J. Mannhart, T. Giamarchi, and M. Filippone, Transport and nonreciprocity in monitored quantum devices: An exact study, Phys. Rev. Lett. 132, 136301 (2024).DOI
  28. [28]C. Elouard, S. K. Manikandan, A. N. Jordan, and G. Haack, Revealing the fuel of a quantum continuous measurement-based refrigerator, Phys. Rev. E 113, 014134 (2026).DOI
  29. [29]R. Sánchez, A. N. Singh, A. N. Jordan, and B. Bhandari, Making the virtual real: Measurement-powered tunneling engines, Phys. Rev. B 113, 125414 (2026).arxiv.org/abs/2510.22394
  30. [30]L. Litzing, G. Schaller, J. König, and N. Szpak, Coupling-energy driven pumping through quantum dots: Role of coherences, Phys. Rev. B 113, 235152 (2026).
  31. [31]L. Gaudreau, S. A. Studenikin, A. S. Sachrajda, P. Zawadzki, A. Kam, J. Lapointe, M. Korkusinski, and P. Hawrylak, Stability Diagram of a Few-Electron Triple Dot, Phys. Rev. Lett. 97, 036807 (2006).DOI
  32. [32]L. P. Kouwenhoven, D. G. Austing, and S. Tarucha, Few-electron quantum dots, Rep. Prog. Phys. 64, 701 (2001).DOI
  33. [33]T. Ihn, Semiconductor Nanostructures: Quantum states and electronic transport (Oxford University Press, 2009).
  34. [34]T. Ihn, S. Gustavsson, U. Gasser, B. Küng, T. Müller, R. Schleser, M. Sigrist, I. Shorubalko, R. Leturcq, and K. Ensslin, Quantum dots investigated with charge detection techniques, Solid State Commun. 149, 1419 (2009).arxiv.org/abs/0905.3398
  35. [35]A. Levy and R. Kosloff, The local approach to quantum transport may violate the second law of thermodynamics, Europhys. Lett. 107, 20004 (2014).DOI
  36. [36]P. P. Potts, A. A. S. Kalaee, and A. Wacker, A thermodynamically consistent Markovian master equation beyond the secular approximation, New J. Phys. 23, 123013 (2021).DOI
  37. [37]A. Rivas and S. F. Huelga, Open Quantum Systems: An Introduction, SpringerBriefs in Physics (Springer Berlin Heidelberg, 2012).
  38. [38]H.-P. Breuer and F. Petruccione, The theory of open quantum systems (Oxford University Press, 2002).
  39. [39]G. Schaller, Open Quantum Systems Far from Equilibrium (Springer, 2014).DOI
  40. [40]T. Brandes, Coherent and collective quantum optical effects in mesoscopic systems, Phys. Rep. 408, 315 (2005).
  41. [41]U. Mukhopadhyay, J. P. Dehollain, C. Reichl, W. Wegscheider, and L. M. K. Vandersypen, A 2 × 2 quantum dot array with controllable inter-dot tunnel couplings, Appl. Phys. Lett. 112, 183505 (2018).
  42. [42]S. Studenikin, M. Korkusinski, A. Bogan, L. Gaudreau, D. G. Austing, A. S. Sachrajda, L. Tracy, J. Reno, and T. Hargett, Single-hole physics in GaAs/AlGaAs double quantum dot system with strong spin-orbit interaction, Semicond. Sci. Technol. 36, 053001 (2021).
  43. [43]T. Nakajima, M. R. Delbecq, T. Otsuka, P. Stano, S. Amaha, J. Yoneda, A. Noiri, K. Kawasaki, K. Takeda, G. Allison, A. Ludwig, A. D. Wieck, D. Loss, and S. Tarucha, Robust Single-Shot Spin Measurement with 99.5% Fidelity in a Quantum Dot Array, Phys. Rev. Lett. 119, 017701 (2017).DOI
  44. [44]J. M. Elzerman, R. Hanson, J. S. Greidanus, L. H. Willems van Beveren, S. De Franceschi, L. M. K. Vandersypen, S. Tarucha, and L. P. Kouwenhoven, Tunable few-electron double quantum dots with integrated charge read-out, Physica E 25, 135 (2004).DOI
  45. [45]L. H. Willems van Beveren, R. Hanson, I. T. Vink, F. H. L. Koppens, L. P. Kouwenhoven, and L. M. K. Vandersypen, Spin filling of a quantum dot derived from excited-state spectroscopy, New J. Phys. 7, 182 (2005).
  46. [46]A. Hoffmann, C. Karlewski, A. Heimes, C. Reichl, W. Wegscheider, G. Schön, K. Ensslin, T. Ihn, and V. F. Maisi, Phonon spectral density in a gaas/algaas double quantum dot, Phys. Rev. Res. 2, 033230 (2020).
  47. [47]A. A. Clerk, M. H. Devoret, S. M. Girvin, F. Marquardt, and R. J. Schoelkopf, Introduction to quantum noise, measurement, and amplification, Rev. Mod. Phys. 82, 1155 (2010).DOI
  48. [48]L. P. Kouwenhoven, C. M. Marcus, P. L. McEuen, S. Tarucha, R. M. Westerwelt, and N. S. Wingreen, Electron transport in quantum dots, in Mesoscopic Electron Transport, edited by L. L. Sohn, L. P. Kouwenhoven, and G. Schön (Springer Netherlands, Dordrecht, 1997) pp. 105–214.DOI
  49. [49]W. G. van der Wiel, S. De Franceschi, J. M. Elzerman, T. Fujisawa, S. Tarucha, and L. P. Kouwenhoven, Electron transport through double quantum dots, Rev. Mod. Phys. 75, 1 (2002).
  50. [50]B. Vacchini, Open Quantum Systems: Foundations and Theory, Graduate Texts in Physics (Springer, Cham, 2024).DOI
  51. [51]J. B. Johnson, Thermal Agitation of Electricity in Conductors, Phys. Rev. 32, 97 (1928).
  52. [52]H. Nyquist, Thermal Agitation of Electric Charge in Conductors, Phys. Rev. 32, 110 (1928).DOI
  53. [53]A. N. Jordan and I. A. Siddiqi, Quantum Measurement (Cambridge University Press, Cambridge, England, UK, 2024).
  54. [54]G. Burkard, T. D. Ladd, A. Pan, J. M. Nichol, and J. R. Petta, Semiconductor spin qubits, Rev. Mod. Phys. 95, 025003 (2023).DOI
  55. [55]R. Sánchez, G. Granger, L. Gaudreau, A. Kam, M. Pioro-Ladrière, S. A. Studenikin, P. Zawadzki, A. S. Sachrajda, and G. Platero, Long-range spin transfer in triple quantum dots, Phys. Rev. Lett. 112, 176803 (2014).pubmed.ncbi.nlm.nih.gov/24836266
  56. [56]J. Knörzer, C. J. van Diepen, T.-K. Hsiao, G. Giedtke, U. Mukhopadhyay, C. Reichl, W. Wegscheider, J. I. Cirac, and L. M. K. Vandersypen, Long-range electron-electron interactions in quantum dot systems and applications in quantum chemistry, Phys. Rev. Res. 4, 033043 (2022).DOI

Paper details

vlnc:W_jsxezuve
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 10

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents