betaFeedback

WorksPhysics and Astronomy

Three Homogenization Models for a Nonlinear Heterogeneous Rod with Microscale Dead Loading

Abstract

A discrete chain of one-dimensional elements with concentrated elastic stiffness is analyzed to investigate the effect of self-equilibrated dead loads acting at the microscale. Three homogenization models are formulated for a finite chain whose total length is much larger than the unit-cell length. Model (i) homogenizes the elastic properties and the microscopic loading simultaneously, yielding an equivalent rod with homogeneous axial and flexural stiffnesses, an effective prestress state, and a distribution of nonlinear rotational springs. In Models (ii) and (iii), the microforces remain periodically distributed as external loads. Model (ii) has homogeneous axial and flexural stiffnesses, whereas Model (iii) retains piecewise-constant axial stiffness. Model (i) is shown to recover the continuum limit of the fully loaded discrete system and to provide the most accurate, fully homogenized description. Incorporating the microforces into the nonlinear homogenization procedure produces an unconventional prestress and a distributed rotational constraint, including rotational springs with negative tangent stiffness. The nonlinear equilibrium equation of Model (i) admits a closed-form solution in terms of elliptic functions, enabling analysis of large deflections and initial post-buckling behavior of a cantilever. The model predicts tensile and compressive buckling, as well as restabilization of the straight configuration. Finally, combined control of the end load and microforces is explored for soft-robotic actuation. Suitable loading paths allow switching between straight and bent configurations and changing the bifurcation character from supercritical to subcritical.

Introduction

The emergence of advanced automated manufacturing has opened the way to materials and structures engineered with increasingly sophisticated microstructural designs. Such designs enable the realization of microstructured chains of elements with lumped elastic stiffness that, once homogenized, can be described as equivalent continuous rods in which axial, shear, and flexural stiffnesses are independent and may, in principle, assume arbitrary values. This capability represents a new paradigm and an opportunity for the development of one-dimensional rod elements with unprecedented mechanical properties [1, 2, 3].

Complementary to the possibilities outlined above, Challamel and co-workers [4, 5] developed a nonlinear homogenization technique for deriving equivalent continuous rods from periodic chains of finite length, rather than from infinite periodic media, building on earlier results by Domokos [6, 7]. They showed that the Engesser and Haringx–Reissner shearable rod models arise as the homogenized response of different microstructural elements; this framework was recently extended in [8].

In the present article, a new microstructural chain is introduced to investigate the independent control of a macroscopic end force and a periodic distribution of microforces applied to each element. The microforces are dead loads acting axially, with zero resultant in the straight configuration taken as the reference. The crucial point is how these microforces enter the homogenization scheme. In fact, the following three different homogenization schemes are developed and shown to yield different results.

  1. The discrete chain and the microforces are homogenized simultaneously, yielding an equivalent rod that is homogeneous in both stiffness and internal forces. In particular, rather than appearing as externally applied loads, the microforces contribute to the internal prestress state of the rod and additionally give rise to a distribution of nonlinear rotational springs along its axis.

  1. The discrete chain is homogenized into an equivalent rod capturing its axial and flexural deformability, while the microforces are neglected at this stage and later applied directly to the rod as external loads. The equivalent rod is elastically homogeneous and subject to a piecewise constant and periodic axial force in its straight configuration.

  1. Flexural behavior is homogenized continuously in the equivalent rod, whereas the axial stiffness remains piecewise constant, periodically alternating between inextensible and axially deformable segments. The microforces are then applied to the equivalent rod as external loads, precisely at the junctions between the inextensible and deformable segments.

The performance of the different homogenization schemes is assessed against the discrete structure, which is taken as the reference. Model (ii) is probably the simplest and most natural choice for homogenization. Relative to the discrete structure, where axially rigid and axially deformable segments alternate, Model (iii) constitutes a refinement of Model (ii). Both models lead to nonlinear governing equations whose internal forces are piecewise smooth and exhibit finite jumps; their analysis is feasible but technically involved2.

The comparison among the three models shows that the most straightforward formulation, Model (ii), provides the least satisfactory performance. In contrast, incorporating the microforces into the homogenization scheme, as in Model (i), combines relative simplicity with improved accuracy.

Interestingly, Model (i) leads to a reinterpretation of the microforces: rather than acting as externally applied loads, they enter the homogenized model as a combination of an internal prestress determined by the boundary conditions and a distribution of rotational springs acting on the rod even when it is unstretched. Consequently, within the homogenized description, the microforces no longer act as external loads. Instead, they give rise to two unconventional continuum features: a novel prestress state and a distributed rotational constraint, neither of which can be realized through conventional loading mechanisms. The effective load governing the prestress combines two distinct contributions, whose relative magnitudes can be tuned to induce different responses, including instability and subsequent restabilization. Moreover, the stiffness of the distributed rotational springs can be tuned to attain negative values, enabling mechanical effects unavailable in conventionally loaded rods.

A crucial advantage of Model (i) is that it also permits the use of analytical techniques that are available only for rods free of distributed loads, unlike Models (ii) and (iii). In particular, Model (i) allows closed-form solutions to be derived for the nonlinear large-deflection response of the rod under end loading. Moreover, for the buckling problem, a weakly nonlinear analysis can be carried out to assess the character of the initial post-critical response. These analytical treatments are not available for the discrete chain, nor for the equivalent rod formulations (ii) and (iii).

Finally, the micromechanical model and its best-performing equivalent rod model are examined to assess their ability to generate unconventional mechanical responses and to explore their potential application as a soft robotic arm [9, 10, 11, 12, 13]. Although such applications would generally involve discrete chains comprising a large number of elements, all examples considered here deliberately employ only a small number of elements. This choice provides a particularly demanding test of the proposed homogenization technique, whose performance was consistently found to be remarkably accurate even under these severe conditions.

For a cantilever configuration, a complete bifurcation analysis is performed. The governing equations of the discrete model are integrated numerically to characterize the post-critical response, whereas an exact analytical solution is obtained for the equivalent rod model. The results reveal the possibility of both tensile [14] and compressive buckling, and in the latter case, the restabilization [15] of the straight configuration.

When interpreted as a soft robotic arm, the structure can undergo flexural cycles that start from the unloaded straight configuration and return to a straight configuration in a loaded, prestressed state. This behavior makes the structure particularly attractive for soft actuation applications.

One-dimensional periodic structure loaded with dead microforces

A one-dimensional discrete chain is considered, composed of axially deformable elements, each with axial stiffness kak_a and initial length ℓ0\ell_0, that are flexurally rigid. The elements are connected by elastic hinges of rotational stiffness krk_r, as shown in Figure 1. A pair of equal and opposite dead forces, each with a magnitude of 2H2H, is applied within each element at a distance Δ\Delta from the hinges. For graphical clarity, these forces are shown as acting on the rigid bars marked in blue. The central portion, with an initial length ℓ0−2Δ\ell_0 - 2\Delta, is axially deformable, whereas the two end portions, each of length Δ\Delta, are inextensible.

Figure 1. One-dimensional chain with lumped elasticity. In the lower figure, the chain is shown in its undeformed configuration. Flexural compliance is provided by hinges of rotational stiffness krk_r, whereas axial deformation is confined to the central segment of axial stiffness kak_a. A pair of equal and opposite dead forces, each of magnitude 2H2H, acts within each element at the ends of the rigid segments of length Δ\Delta, producing the same elongation in every unit cell, as shown in the upper figure.

The practical realization of the prescribed microforces lies beyond the scope of the present study, which focuses instead on their mechanical consequences within the proposed theoretical framework. Nevertheless, a possible strategy for generating dead forces of opposite sign has recently been presented in [16], providing a potential basis for the experimental implementation of such loading conditions.

Kinematics of the unit cell

The microstructure shown in Figure 1, in its undeformed (lower part) and axially loaded (upper part) configurations, undergoes large deformations, as illustrated in Figure 2. The figure shows a single unit cell subjected to the external forces 2H2H and the end forces transmitted by the adjacent cells. Denoting the displacement of the ii–th node by ui=uie1+vie2\mathbf{u}_i = u_i\mathbf{e}_1+v_i\mathbf{e}_2, where e1\mathbf{e}_1 and e2\mathbf{e}_2 are the horizontal and vertical unit vectors, respectively, the relative displacement of the nodes at the ends of the element is

Figure 2. The ii-th element in its undeformed configuration, with length ℓ0\ell_0, and in its deformed configuration, with length ℓi=ℓ0+di\ell_i=\ell_0+d_i and rotation θi\theta_i relative to the unit vector e1\mathbf{e}_1. The forces and moments transmitted by the adjacent cells at the left end, Ni−1+N_{i-1}^{+} and Mi−1+M_{i-1}^{+}, and at the right end, Ni+N_i^{+} and Mi+M_i^{+}, are also shown. The microforces 2H2H remain horizontal because they are dead loads.

ui−ui−1=(ℓ0+di)ti−ℓ0e1(1)\mathbf{u}_i-\mathbf{u}_{i-1}=(\ell_0+d_i)\mathbf{t}_i-\ell_0\mathbf{e}_1 \tag*{(1)}

where did_i is the axial elongation of the element and ti\mathbf{t}_i is the axial unit vector. The axial unit vector ti\mathbf{t}_i and the unit normal ni\mathbf{n}_i are defined as

ti=cos⁡θie1+sin⁡θie2,ni=sin⁡θie1−cos⁡θie2(2)\mathbf{t}_i=\cos\theta_i\mathbf{e}_1+\sin\theta_i\mathbf{e}_2,\qquad\mathbf{n}_i=\sin\theta_i\mathbf{e}_1-\cos\theta_i\mathbf{e}_2 \tag*{(2)}

where θi\theta_i is the rotation angle of the element.

The current configuration of the ii-th unit cell is described by four scalar kinematic variables: the two components of the displacement ui−1\mathbf{u}_{i-1} of its left end, the rotation θi\theta_i, and the axial strain εi=di/ℓ0\varepsilon_i=d_i/\ell_0. The axial stretch λi\lambda_i of the element is defined as

λi=1+εi=1+diℓ0.(3)\lambda_i=1+\varepsilon_i=1+\frac{d_i}{\ell_0}. \tag*{(3)}

From Eq. (1), the following compatibility equations can be derived

λi=(1+ui−ui−1ℓ0)cos⁡θi+vi−vi−1ℓ0sin⁡θi,γi=−(1+ui−ui−1ℓ0)sin⁡θi+vi−vi−1ℓ0cos⁡θi=0,(4)\begin{aligned} \lambda_i&=\left(1+\frac{u_i-u_{i-1}}{\ell_0}\right)\cos\theta_i+\frac{v_i-v_{i-1}}{\ell_0}\sin\theta_i,\\ \gamma_i&=-\left(1+\frac{u_i-u_{i-1}}{\ell_0}\right)\sin\theta_i+\frac{v_i-v_{i-1}}{\ell_0}\cos\theta_i=0, \tag*{(4)} \end{aligned}

where the first relation expresses the axial stretch in terms of the nodal displacements and the element rotation, whereas the second enforces the unshearability constraint.

Governing equations of the unit cell

The work done by the microforces is

−2He1⋅(−Δe1+ui−1+Δti)⏟C′−C+2He1⋅(Δe1+ui−Δti)⏟G′−G(5)-2H\mathbf{e}_1\cdot\underbrace{(-\Delta\mathbf{e}_1+\mathbf{u}_{i-1}+\Delta\mathbf{t}_i)}_{C'-C}+2H\mathbf{e}_1\cdot\underbrace{(\Delta\mathbf{e}_1+\mathbf{u}_i-\Delta\mathbf{t}_i)}_{G'-G} \tag*{(5)}

where C′−CC^{\prime}-C and G′−GG^{\prime}-G are the displacement vectors of the points at which the microforces are applied.

The total potential energy of the unit cell is given by the elastic energy stored in the axial and rotational springs minus the work done by the end forces Ni−1+N_{i-1}^{+} and Ni+N_i^{+}, end moments Mi−1+M_{i-1}^{+} and Mi+M_i^{+}, and microforces 2H2H. Using the kinematic relation introduced previously, it can be written as

Wi=kr2(θi+1−θi)2+ka2di2+Mi−1+θi−Mi+θi+1+Ni−1+⋅(ui+ℓ0e1−(ℓ0+di)ti)−Ni+⋅ui+2H{ℓ0−2Δ−(ℓ0−2Δ+di)cos⁡θi}.(6)W_i=\frac{k_r}{2}\left(\theta_{i+1}-\theta_i\right)^2+\frac{k_a}{2}d_i^2+M_{i-1}^{+}\theta_i-M_i^{+}\theta_{i+1}+N_{i-1}^{+}\cdot\left(\mathbf{u}_i+\ell_0\mathbf{e}_1-(\ell_0+d_i)\mathbf{t}_i\right) -N_i^{+}\cdot\mathbf{u}_i+2H\left\{\ell_0-2\Delta-\left(\ell_0-2\Delta+d_i\right)\cos\theta_i\right\}. \tag*{(6)}

The stationarity of WiW_i with respect to θi\theta_i, θi+1\theta_{i+1}, ui\mathbf{u}_i, and did_i yields, respectively, the following equilibrium and constitutive equations

Moment balanceMi+=Mi−1++(ℓ0+di)Ni−1+⋅ni+2H(ℓ0−2Δ+di)sin⁡θi,Moment–rotation relationMi+=kr(θi+1−θi),Force balanceNi+=Ni−1+,Axial constitutive relationNi−1+⋅ti=kadi−2Hcos⁡θi.(7)\begin{aligned} \text{Moment balance}\quad&M_i^{+}=M_{i-1}^{+}+(\ell_0+d_i)N_{i-1}^{+}\cdot\mathbf{n}_i+2H(\ell_0-2\Delta+d_i)\sin\theta_i,\\ \text{Moment--rotation relation}\quad&M_i^{+}=k_r(\theta_{i+1}-\theta_i),\\ \text{Force balance}\quad&N_i^{+}=N_{i-1}^{+},\\ \text{Axial constitutive relation}\quad&N_{i-1}^{+}\cdot\mathbf{t}_i=k_a d_i-2H\cos\theta_i. \tag*{(7)} \end{aligned}

The microforces have zero resultant on each unit cell and therefore do not alter the transmitted resultant force between adjacent hinges.

Analysis of the periodic discrete structure

References

  1. [1]T. Frenzel, M. Kadic, and M. Wegener. “Three-dimensional mechanical metamaterials with a twist”. In: Science 358.6366 (Nov. 24, 2017), pp. 1072–1074. DOI: 10.1126/science.aao4640.DOI
  2. [2]T. Frenzel, V. Hahn, P. Ziemke, J. L. G. Schneider, Y. Chen, P. Kiefer, P. Gumbsch, and M. Wegener. “Large characteristic lengths in 3D chiral elastic metamaterials”. In: Communications Materials 2 (Jan. 4, 2021), p. 4. DOI: 10.1038/s43246-020-00107-w.DOI
  3. [3]J. A. Iglesias Martínez, M. F. Groß, Y. Chen, T. Frenzel, V. Laude, M. Kadic, and M. Wegener. “Experimental observation of roton-like dispersion relations in metamaterials”. In: Science Advances 7.49 (Dec. 3, 2021), eabm2189. DOI: 10.1126/sciadv.abm2189.DOI
  4. [4]A. Kocsis, N. Challamel, and G. Karolyi. “Discrete and nonlocal models of Engesser and Haringx elastica”. In: International Journal of Mechanical Sciences 130 (2017), pp. 571–585. DOI: 10.1016/j.ijmecsci.2017.05.037.DOI
  5. [5]A. Kocsis and N. Challamel. “On the foundation of a generalized nonlocal extensible shear beam model from discrete interactions”. In: Generalized Models and Non-classical Approaches in Complex Materials 1. Ed. by H. Altenbach, J. Pouget, M. Rousseau, B. Collet, and T. Michelitsch. Springer International Publishing, 2018, pp. 451–486.DOI
  6. [6]G. Domokos. “Qualitative convergence in the discrete approximation of the Euler problem”. In: Mechanics of Structures and Machines: An International Journal 21:4 (1993), pp. 529–543.DOI
  7. [7]G. Domokos and P. Holmes. “Euler’s problem, Euler’s method, and the standard map; or, the discrete charm of buckling”. In: Journal of Nonlinear Science 3.1 (1993), pp. 109–151.DOI
  8. [8]M. Paradiso, F. Dal Corso, and D. Bigoni. “A nonlinear model of shearable elastic rod from an origami-like microstructure displaying folding and faulting”. In: Journal of the Mechanics and Physics of Solids 200 (2025), p. 106100. DOI: 10.1016/j.jmps.2025.106100.DOI
  9. [9]C. Armanini, F. Dal Corso, D. Misseroni, and D. Bigoni. “From the elastica compass to the elastica catapult: an essay on the mechanics of soft robot arm”. In: Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences 473 (2017), p. 20160870. DOI: 10.1098/rspa.2016.0870.DOI
  10. [10]C. Armanini, F. Boyer, A. T. Mathew, C. Duriez, and F. Renda. “Soft Robots Modeling: A Structured Overview”. In: IEEE Transactions on Robotics 39.3 (June 2023), pp. 1728–1748. DOI: 10.1109/TRO.2022.3231360.DOI
  11. [11]A. A. Sipos and P. L. Várkonyi. “The longest soft robotic arm”. In: International Journal of Non-Linear Mechanics 119 (Mar. 2020), p. 103354. DOI: 10.1016/j.ijnonlinmec.2019.103354.DOI
  12. [12]F. Falope, L. Lanzoni, and M. Tarantino. “Finite bending of non-slender beams and the limitations of the Elastica theory”. In: International Journal of Mechanical Sciences 222 (May 15, 2022), p. 107187. DOI: 10.1016/j.ijmecsci.2022.107187.DOI
  13. [13]S. P. C. Dhanakoti. “Stability of cantilever-like structures with applications to soft robot arms”. In: Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences 481.2312 (Apr. 30, 2025), p. 20240561. DOI: 10.1098/rspa.2024.0561.DOI
  14. [14]D. Zaccaria, D. Bigoni, G. Noselli, and D. Misseroni. “Structures buckling under tensile dead load”. In: Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences 467.2130 (June 8, 2011), pp. 1686–1700. DOI: 10.1098/rspa.2010.0505.
  15. [15]P. Koutsogiannakis, D. Bigoni, and F. Dal Corso. “Double restabilization and design of force–displacement response of the extensible elastica with movable constraints”. In: European Journal of Mechanics - A/Solids 100 (July 2023), p. 104745. DOI: 10.1016/j.euromechsol.2022.104745.DOI
  16. [16]D. Bigoni, D. Misseroni, and A. Piccolroaz. “The strange mechanics of an elastic rod under null-resultant transverse loads”. In: Journal of the Mechanics and Physics of Solids 212 (2026), p. 106590. DOI: 10.1016/j.jmps.2026.106590.DOI
  17. [17]Y. Fu, Y.-S. Wang, and Y. Fu. “Wrinkling of a film/substrate bilayer with periodic material properties: An assessment of the Winkler foundation model”. In: International Journal of Non-Linear Mechanics 166 (2024), p. 104815. DOI: 10.1016/j.ijnonlinmec.2024.104815.DOI
  18. [18]A. Humer. “Exact solutions for the buckling and postbuckling of shear-deformable beams”. In: Acta Mechanica 224.7 (July 2013), pp. 1493–1525. DOI: 10.1007/s00707-013-0818-1.DOI
  19. [19]M. Batista. “A closed-form solution for Reissner planar finite-strain beam using Jacobi elliptic functions”. In: International Journal of Solids and Structures 87 (2016), pp. 153–166. DOI: 10.1016/j.ijsolstr.2016.02.020.DOI
  20. [20]G. Teschl. Ordinary differential equations and dynamical systems. Graduate studies in mathematics vol. 140. Providence: American mathematical society, 2012.DOI
  21. [21]Wolfram Research, Inc. Mathematica, Version 15.0. Champaign, IL, 2026.
  22. [22]B. Budiansky. “Theory of Buckling and Post-Buckling Behavior of Elastic Structures”. In: Advances in Applied Mechanics. Vol. 14. Academic Press, 1974, pp. 1–65. DOI: 10.1016/S0065-2156(08)70030-9.DOI

Paper details

vlnc:W_kedpzc9j
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 2

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents