betaFeedback

WorksPhysics and Astronomy

Rashba Effect and Type-III Broken-Gap Band Alignment in MoTe2_2/HfS2_2 van der Waals Heterostructures for Tunnel Field-Effect Transistors

Abstract

Two-dimensional van der Waals heterostructures (vdWHs) based on transition metal dichalcogenides (TMDs) have emerged as promising platforms for next-generation low-power electronics and spintronics. Here, we investigate the structural, electronic, and spin properties of MoTe2_2/HfS2_2 vdWHs using first-principles density functional theory calculations. Our results reveal an intrinsic type-III (broken-gap) band alignment, making this heterostructure highly attractive for tunnel field-effect transistor (TFET) applications. In addition, inversion-symmetry breaking at the interface, combined with strong spin-orbit coupling, induces a pronounced Rashba spin splitting around the ΓΓ point, accompanied by characteristic helical spin textures. We further show that external vertical electric fields, twist engineering, and both out-of-plane and in-plane strain provide efficient means to tune the band alignment, charge transfer, and Rashba parameters. In particular, electric fields and mechanical strain can drive reversible transitions between type-II and type-III band alignments while simultaneously modifying the Rashba spin texture and the band-to-band tunneling (BTBT) window. The twisted heterostructure with θ=21.79∘θ= 21.79^\circ exhibits similar tunability, including strain-induced transitions between distinct band-alignment regimes. These findings establish MoTe2_2/HfS2_2 vdWHs as versatile multifunctional platforms combining electrically tunable Rashba spin splitting with controllable type-II/type-III band alignment, offering promising opportunities for next-generation TFETs and spintronic devices.

Introduction

The relentless progress of modern electronics over the past decades has been largely driven by the continuous scaling of conventional metal–oxide–semiconductor field-effect transistors (MOSFETs). However, the further miniaturization of these devices faces fundamental physical limitations associated with power dissipation, thermal management, and the thermionic limit of the subthreshold swing (SS), which is restricted to approximately 60 mV/dec at room temperature due to the thermally activated carrier injection mechanism [1, 2]. These challenges have stimulated the search for alternative transistor architectures capable of operating with higher energy efficiency and steeper switching characteristics. In this context, tunnel field-effect transistors (TFETs) have emerged as promising candidates. Their operation relies on band-to-band tunneling (BTBT), enabling sub-threshold swings below the thermionic limit and opening

a pathway toward low-power nanoelectronic devices [3, 4, 5].

Two-dimensional (2D) van der Waals heterostructures (vdWHs) based on transition metal dichalcogenides (TMDs) have attracted considerable attention owing to their remarkable electronic, optical, and spin-related properties, as well as their potential applications in nano-electronics and spintronics [6, 7, 8, 9]. The weak van der Waals interaction between adjacent layers allows the vertical stacking of different monolayers without stringent lattice-matching requirements, enabling the design of artificial heterostructures with tunable band alignments and interfacial properties [10, 11, 12, 13, 14]. In particular, heterostructures exhibiting type–III (broken-gap) band alignment are highly desirable for TFET applications because they facilitate efficient band-to-band tunneling between the valence-band states of one layer and the conduction-band states of the adjacent layer. [15, 16, 17, 18] Recent theoretical and experimental studies have demonstrated that type–III TMD-based vdWHs constitute promising platforms for low-power electronic and optoelectronic devices [15, 16, 18, 19, 20, 21, 22].

Type–III band alignment can be achieved through the stacking of selected TMD monolayers and related layered materials, such as MoTe2_2, SnSe2_2, ZrS2_2, and HfS2_2. Nevertheless, the number of experimentally realized and theoretically predicted 2D heterostructures that intrinsically exhibit a broken-gap alignment remains relatively limited, particularly those simultaneously combining favorable properties for TFET and spintronic applications. Consequently, the exploration of new material combinations capable of hosting both type–III band alignment and tunable electronic properties remains an important research direction. Motivated by this scenario, we focus here on the MoTe2_2/HfS2_2 van der Waals heterostructure.

Recent studies have shown that monolayer MoTe2_2 exhibits temperature-dependent Rydberg excitons and trions, together with strong gate tunability, highlighting its potential for near-infrared optoelectronic applications [23]. In addition, strain engineering in MoTe2_2 has revealed significant opportunities for tailoring phase transitions, defect formation, and electronic properties, owing to the strong strain dependence of its structural phases [24]. More recently, monolayer TdT_d–MoTe2_2 has been reported to exhibit gate-controlled superconductivity [25] [26, 27] and signatures of topological superconductivity [28].

On the other hand, monolayer HfS2_2 possesses equally attractive electronic characteristics. Theoretical studies predict strain-induced indirect-to-direct band-gap transitions, broadening its potential for optoelectronic applications [29]. Furthermore, significant improvements in its thermoelectric performance have been predicted under strain [30]. Experimentally, few-layer HfS2_2 transistors exhibit excellent current saturation and high on/off current ratios, demonstrating their suitability for ultralow-power electronic devices [31].

Previous investigations of related heterostructures, such as ZrS2_2/MoTe2_2 and WTe2_2/HfS2_2, have shown that combining TMDs in the H and T phases can simultaneously induce type–III band alignment and Rashba spin splitting, opening new opportunities for multifunctional electronic devices, TFETs, and spintronic applications [10, 11, 16]. Consequently, MoTe2_2 and HfS2_2 emerge as particularly promising building blocks for next-generation 2D heterostructures in which both charge and spin degrees of freedom can be simultaneously exploited and controlled.

The Rashba effect plays a fundamental role in the electronic states of surfaces and heterostructures, originating from the interplay between strong spin–orbit coupling (SOC) and inversion-symmetry breaking. This mechanism has become one of the cornerstones of modern spintronics because it enables electrical manipulation of spin polarization without the need for external magnetic fields [32, 33]. In vdWHs, interfacial charge redistribution and the resulting built-in electric field can break out-of-plane inversion symmetry, leading to momentum-dependent spin splitting near high-symmetry points of the Brillouin zone [33, 34]. The resulting Rashba spin textures are highly attractive for spin manipulation, spin filtering, and spin transport applications in low-dimensional systems [32, 33, 35]. Moreover, the coexistence of Rashba spin splitting and type–III band alignment may enable the integration of spintronic and tunneling functionalities within a single material platform [10, 11, 16] [33].

Another appealing feature of vdWHs is the possibility of externally tuning their electronic properties through strain engineering, twist-angle modulation, and external electric fields [15, 16] [36, 37, 38]. Recent studies have shown that vertical electric fields can substantially modify the relative positions of the valence- and conduction-band edges, inducing transitions between type–II and type–III band alignments and strongly affecting BTBT processes [11, 15, 16, 17]. Likewise, twisted heterostructures can generate Moiré superlattices and alter the interlayer coupling, resulting in pronounced changes in the electronic structure, charge transfer, and correlated properties [37, 39]. These effects make electrically controlled and twisted vdWHs particularly attractive platforms for multifunctional nanoelectronic, spintronic, and quantum devices.

Motivated by these developments, we investigate the structural, electronic, and spin-related properties of the MoTe2_2/HfS2_2 van der Waals heterostructure using first-principles density functional theory (DFT) calculations including spin–orbit coupling and van der Waals corrections. Our results show that the energetically most stable stacking configuration lies remarkably close to the type-II/type-III band-alignment boundary. Furthermore, we explore the effects of external electric fields, mechanical strain, and twist-angle engineering, demonstrating that these external perturbations provide efficient control over charge transfer, band alignment, and spin properties, enabling reversible transitions between type-II and type-III band-alignment regimes. The computational details are provided in the Supplementary Information (SI) [40]. These findings establish the MoTe2_2/HfS2_2 heterostructure as a promising platform for TFETs, spintronic applications, and low-power multifunctional nanoelectronic devices.

RESULTS AND DISCUSSIONS

Structural and Electronic Properties of MoTe2_2/HfS2_2 Heterostructure

The MoTe2_2/HfS2_2 van der Waals heterostructure (vdWH) was constructed from the fully relaxed bulk phases of MoTe2_2 and HfS2_2. Bulk MoTe2_2 was considered in its trigonal prismatic (hexagonal H) phase, with experimental lattice parameters of a=3.520a = 3.520 Å, c=13.910c = 13.910 Å, and unit-cell volume V=149.260V = 149.260 Å3^3, as reported by Uesugi et al. [40]. Bulk HfS2_2 was modeled in its octahedral (T) phase, exhibiting experimental lattice parameters of a=3.623a = 3.623 Å, c=5.841c = 5.841 Å, and unit-cell volume V=66.398V = 66.398 Å3^3, according to Rimmington & Balchin [41].

To accurately describe the structural properties of the constituent materials, several exchange-correlation functionals were tested, including PBE [42], PBE+D2 [43, 44], PBE+D3 [45], PBEsol [46], vdW–DF2 [47], and rev-vdW–DF2 [48]. Among them, the PBE+D3 functional provided the best agreement with the experimental structural parameters of both bulk compounds (see Table S2 in Section I of the SI) [49] and was therefore adopted throughout this work.

MoTe2_2HfS2_2
aa (Å)cc (Å)VV (Å3^3)aa (Å)cc (Å)VV (Å3^3)
Exp3.520§13.910§149.260§3.623†5.841†66.398†
PBE3.55115.122165.1293.6446.67776.764
PBE+D23.52113.991150.1973.6315.64864.480
PBE+D33.51414.002149.7683.6195.86766.529
PBEsol3,49013.952147.1983.5875.91365.891
vdW−DF23.71214.899177.7593.7366.04973.125
rev−vdW−DF23.52914.051151.5523.6135.82665.863

Table S2. Lattice parameters of bulk MoTe2_2 and HfS2_2 calculated with functionals (PBE, PBE+D2, PBE+D3, PBEsol, vdW-DF2 and rev-vdW-DF2) and their corresponding experimental values.

Figure 1(a) and Figure 1(b) display the isolated MoTe2_2 (1L–MoTe2_2) and HfS2_2 (1L–HfS2_2) monolayers, respectively, while Figure 1(c) illustrates the resulting heterostructure. The yellow, green, brown, and blue spheres denote S, Hf, Te, and Mo atoms, respectively. Owing to the difference between the lattice parameters of the constituent monolayers, direct stacking would produce a lattice mismatch of approximately 3%, which remains within the range experimentally achievable for van der Waals heterostructures. The lattice mismatch is defined as [(aHfS2−aMoTe2)/aMoTe2]×100%[(a_{\mathrm{HfS_2}}-a_{\mathrm{MoTe_2}})/a_{\mathrm{MoTe_2}}]\times100\%. Under this condition, the HfS2_2 layer would be subjected to compressive strain, whereas the MoTe2_2 layer would experience tensile strain. To minimize this effect, the average lattice parameter obtained from the relaxed bulk structures was adopted for the heterostructure construction. This approach leads to a nearly uniform strain distribution between the layers and results in a residual strain of only ∼1.5%\sim1.5\%. Considering the small magnitude of this deformation, the experimental realization of the proposed heterostructure is expected to be feasible.

Crystal structures, projected band structures, and band alignment diagrams for MoTe2/HfS2

Figure 1. (Color online) (a)–(c) Side views of the crystal structures of 1L–MoTe2_2, 1L–HfS2_2, and the MoTe2_2/HfS2_2 heterostructure, respectively, illustrating the approach of the isolated monolayers leading to the formation of the van der Waals heterostructure (vdWH). The yellow, green, brown, and blue spheres represent S, Hf, Te, and Mo atoms, respectively. (d)–(e) Projected band structures of the isolated MoTe2_2 (1L–MoTe2_2) and HfS2_2 (1L–HfS2_2) monolayers, respectively. (f) Projected band structure of the MoTe2_2/HfS2_2 vdWH for the most stable stacking configuration, vdWH–IV, where the electronic contributions from MoTe2_2 and HfS2_2 are shown in blue and green, respectively. (g) Schematic band alignment diagrams with respect to the vacuum level for 1L–MoTe2_2 and 1L–HfS2_2 before and after vdWH formation, evidencing an intrinsic broken-gap type–III band alignment.

We investigated six high-symmetry stacking configurations for the MoTe2_2/HfS2_2 vdWH, as illustrated in Figure S1–(Figure S1) of the SI [49]. The considered configurations are: i. vdWH–I, where the upper S atoms (SupS_{\mathrm{up}}) are aligned with the Te atoms, while the Hf atoms occupy the Mo sites; ii. vdWH–II, characterized by the alignment of Hf atoms with the Te sites and the lower S atoms (SdwS_{\mathrm{dw}}) with the Mo sites; iii. vdWH–III, in which the SdwS_{\mathrm{dw}} atoms are located above the Te atoms and the SupS_{\mathrm{up}} atoms above the Mo sites; iv. vdWH–IV, where the SupS_{\mathrm{up}} atoms are aligned with the Te atoms, while the SdwS_{\mathrm{dw}} atoms are positioned above the Mo atoms; v. vdWH–V, in which the SdwS_{\mathrm{dw}} atoms are located above the Te atoms and the Hf atoms above the Mo atoms; and vi. vdWH–VI, where the Hf atoms are positioned above the Te atoms, while the SupS_{\mathrm{up}} atoms occupy the sites above the Mo atoms. The fully relaxed atomic structures corresponding to each stacking configuration are presented in Section I of the SI [49].

Atomic configurations of the MoTe$_2$/HfS$_2$ heterostructure for different high-symmetry stacking arrangements

Figure S1. (a)–(f) Atomic configurations of the MoTe2_2/HfS2_2 heterostructure for different high-symmetry stacking arrangements. The yellow, green, brown, and blue spheres denote S, Hf, Te, and Mo atoms, respectively.

To determine the most stable stacking arrangement, six high-symmetry configurations were considered, as shown in Figure S1–(Figure S1) of the SI [49]. The corresponding relaxed atomic structures are also provided in Section I of the SI. The interfacial stability was evaluated through the binding energy (EbE_b),

Eb=(EMoTe2/HfS2−EMoTe2−EHfS2)/A,E_b=(E_{\mathrm{MoTe_2/HfS_2}}-E_{\mathrm{MoTe_2}}-E_{\mathrm{HfS_2}})/A,

where EMoTe2/HfS2E_{\mathrm{MoTe_2/HfS_2}} is the total energy of the heterostructure, EMoTe2E_{\mathrm{MoTe_2}} and EHfS2E_{\mathrm{HfS_2}} are the energies of the strained isolated monolayers, and AA is the in-plane area of the unit cell. The calculated total energies, relative energies (E−EvdWH−IVE-E_{\mathrm{vdWH-IV}}), and binding energies are summarized in Table S3 of the SI [49]. The analysis of both E−EvdWH−IVE-E_{\mathrm{vdWH-IV}} and EbE_b reveals that the vdWH–IV stacking configuration is the energetically most favorable structure, exhibiting a binding energy of −26.430-26.430 meV/A˚2\text{\AA}^2. This value falls within the range reported for other TMD-based van der Waals heterostructures [12, 15, 16, 17]. The negative binding energy confirms the stability of the heterostructure. The remaining stacking configurations also exhibit negative binding energies, ranging from −18.649-18.649 to −26.430-26.430 meV/A˚2\text{\AA}^2, indicating that all considered structures are energetically stable.

vdWH-IvdWH-IIvdWH-IIIvdWH-IVvdWH-VvdWH-VI
dintd_{\mathrm{int}} (Å)3.1073.2433.7233.1583.6933.316
dMo−Hfd_{\mathrm{Mo-Hf}} (Å)6.3726.5126.9926.4276.9606.588
EbE_b (meV/Å2^2)-26.121-25.052-18.649-26.430-18.929-23.872
Total Energy (eV)-42.219-42.207-42.137-42.222-42.140-42.194
E−EvdWH−IVE-E_{\mathrm{vdWH-IV}} (eV)-3.412-15.185-85.7210.000-82.635-28.183
ΔECBM−VBM\Delta E_{\mathrm{CBM-VBM}} (PBE) (eV)0.0350.0110.0540.0130.093-0.020
ΔECBM−VBM\Delta E_{\mathrm{CBM-VBM}} (PBE+SOC) (eV)-0.027-0.0470.023-0.0480.017-0.082
ΔECBM−VBM\Delta E_{\mathrm{CBM-VBM}} (HSE06) (eV)0.2710.2280.3240.2340.3920.122
Δq\Delta q (e)0.0420.0350.0280.0390.0290.034
kRk_R (Å−1^{-1})0.1460.1360.1510.1360.1510.146
ERE_R (meV)21.21616.4929.08817.2569.66515.874

Table S3. Calculated structural, energetic, and electronic properties of the MoTe2_2/HfS2_2 heterostructure for different high-symmetry stacking configurations (vdWH-I to vdWH-VI). The interlayer distance (dintd_{\mathrm{int}}), Mo–Hf vertical separation (dMo−Hfd_{\mathrm{Mo-Hf}}), binding energy (EbE_b), and total energy are reported. The relative energy (E−EvdWH−IVE-E_{\mathrm{vdWH-IV}}) is referenced to the most stable configuration (vdWH-IV). The band alignment parameter (ΔECBM−VBM\Delta E_{\mathrm{CBM-VBM}}) is evaluated using the PBE, PBE+SOC, and HSE06 functionals. The charge transfer (Δq\Delta q) is obtained from Bader charge analysis. The Rashba momentum offset (kRk_R) and Rashba energy (ERE_R) are also listed for each stacking configuration.

We also investigated the interlayer distance (dintd_{\mathrm{int}}) and the separation between the metallic Mo and Hf atoms (dMo−Hfd_{\mathrm{Mo-Hf}}). For the vdWH–IV configuration, we obtained dint=3.158d_{\mathrm{int}}=3.158 Å and dMo−Hf=6.427d_{\mathrm{Mo-Hf}}=6.427 Å. The calculated values of dintd_{\mathrm{int}} are in good agreement with previously reported results [50]. Figure S2–(Figure S2) of the SI [49] show the variation of dMo−Hfd_{\mathrm{Mo-Hf}} for the six high-symmetry stacking configurations considered in this work. Based on these results, all subsequent analyses were carried out using only the vdWH–IV configuration.

Interlayer distance and relative energy as functions of high-symmetry stacking configurations for the MoTe$_2$/HfS$_2$ heterostructure

Figure S2. (a)–(b) Interlayer distance dMo−Hfd_{\mathrm{Mo-Hf}} as a function of the high-symmetry stacking configurations for the MoTe2_2/HfS2_2 heterostructure. (c)–(d) Corresponding relative energy E−EvdWH−IVE-E_{\mathrm{vdWH-IV}} for each stacking. Black squares represent the calculated data points, while solid lines denote the curve fitting. The dashed vertical lines indicate the different stacking configurations, illustrated schematically above each panel.

To further evaluate the thermal stability of the MoTe2_2/HfS2_2 vdWH, ab initio molecular dynamics (AIMD) simulations were performed at 300 K for 5 ps. The corresponding results are presented in Figure S3 of the SI [49]. As shown in Figure S3, the heterostructure remains structurally stable throughout the simulation, exhibiting neither structural reconstruction nor layer separation. Although a slight relative lateral displacement between the MoTe2_2 and HfS2_2 layers is observed after 5 ps, which can be attributed to the weak interlayer van der Waals interaction, the overall crystal framework is preserved. The top and side views of the final configuration, displayed as insets, further confirm the structural robustness of the heterostructure. Moreover, the total energy per atom exhibits only small fluctuations around its equilibrium value after the initial thermalization stage (approximately 0–1 ps), without any noticeable energy drift. Figure S3 presents the temperature evolution during the AIMD simulation. Although moderate fluctuations are observed, particularly at the beginning of the trajectory, the temperature remains close to the target value of 300 K throughout the simulation. Such behavior is consistent with previous AIMD studies of thermally stable two-dimensional van der Waals heterostructures, including systems exhibiting type–III band alignment [11, 15]. These results demonstrate that the MoTe2_2/HfS2_2 vdWH is thermally stable at room temperature, supporting its potential experimental realization and its suitability for future nanoelectronic and spintronic device applications.

Ab initio molecular dynamics simulations of the MoTe$_2$/HfS$_2$ van der Waals heterostructure at 300 K, showing total energy and temperature fluctuations

Figure S3. Ab initio molecular dynamics (AIMD) simulations of the MoTe2_2/HfS2_2 van der Waals heterostructure at 300 K. (a) Time evolution of the total energy per atom. (b) Temperature fluctuations throughout the simulation. The top and side views shown in the insets correspond to the final configuration after 5 ps, confirming the thermal stability of the heterostructure at room temperature.

We now turn to the electronic properties of the constituent monolayers and the heterostructure. The electronic band structures were calculated within the PBE functional including spin–orbit coupling (PBE+SOC). Figure 1(d) shows the band structure of 1L–MoTe2_2, which exhibits a direct band gap of 0.90 eV at the K point. In contrast, Figure 1(e) displays the band structure of 1L–HfS2_2, characterized by an indirect band gap of 0.96 eV. These values are slightly smaller than those previously reported in the literature [51, 52], but remain in good qualitative agreement. The reduction can be attributed to the small lattice strain (∼1.5%\sim1.5\%) introduced during the construction of the heterostructure, together with the inclusion of SOC effects. To verify this interpretation, we additionally calculated the band structures of the unstrained monolayers, shown in Figure S5–(Figure S5) of the SI [49]. In this case, the calculated band gaps are 1.01 eV for 1L–MoTe2_2 and 1.18 eV for 1L–HfS2_2, in closer agreement with previous theoretical reports [51, 52]. We find that the applied strain does not alter the nature of the band gaps, but only induces a modest reduction in their magnitude. Therefore, the strained monolayers were adopted throughout this work to ensure consistency with the lattice-matched heterostructure calculations.

Figure S5. Electronic band structures calculated using PBE+SOC for the isolated monolayers of (a) 1L–MoTe2_2 and (b) 1L–HfS2_2. The solid lines correspond to the monolayers under the small in-plane strain (∼1.5%\sim1.5\%) inherited from the formation of the MoTe2_2/HfS2_2 heterostructure, while the dotted lines represent the fully relaxed strain-free monolayers obtained using their optimized lattice parameters. The comparison shows that the applied strain induces only slight modifications in the electronic structure and band gap values.

Figure 1(f) presents the electronic band structure of the most stable MoTe2_2/HfS2_2 heterostructure (vdWH–IV). A qualitatively similar behavior is observed for the remaining stacking configurations, whose band structures are shown in Figure S6–(Figure S6) of the SI [49]. The electronic structure of the heterostructure can be understood, to first approximation, as a superposition of the bands of the isolated monolayers. The conduction-band minimum (CBM) is predominantly derived from the HfS2_2 layer, whereas the valence-band maximum (VBM) originates mainly from the MoTe2_2 layer, giving rise to a type–III (broken-gap) band alignment. When SOC is included, the energy difference between the CBM and VBM is ΔECBM−VBM=−0.048\Delta E_{\mathrm{CBM-VBM}}=-0.048 eV, indicating a finite overlap between the conduction- and valence-band edges. In contrast, a slightly positive value of ΔECBM−VBM=0.013\Delta E_{\mathrm{CBM-VBM}}=0.013 eV is obtained without SOC. The band structures calculated with and without SOC for the remaining stacking configurations, together with the corresponding values of ΔECBM−VBM\Delta E_{\mathrm{CBM-VBM}}, are provided in Figure S6 and Figure S7 and Table S3 of the SI [49], respectively.

Electronic band structures of the MoTe$_2$/HfS$_2$ heterostructure for six high-symmetry stacking configurations

Figure S6. Electronic band structures of the MoTe2_2/HfS2_2 heterostructure for different high-symmetry stacking configurations (vdWH-I to vdWH-VI), calculated using the PBE functional including spin–orbit coupling (PBE+SOC). The band structures are plotted along the high-symmetry path KK–Γ\Gamma–MM–KK. The blue and green curves represent the contributions from MoTe2_2 and HfS2_2 layers, respectively, highlighting the interlayer hybridization and band alignment for each stacking configuration.

Electronic band structures of the MoTe$_2$/HfS$_2$ heterostructure for six high-symmetry stacking configurations

Figure S7. Electronic band structures of the MoTe2_2/HfS2_2 heterostructure for the six high-symmetry stacking configurations (vdWH-I to vdWH-VI), calculated within the PBE approximation without spin–orbit coupling (SOC). Compared to the PBE+SOC results, the overall band dispersion is preserved, while spin-related splittings are absent. This comparison highlights the role of spin–orbit coupling in modifying the band structure, particularly near the band edges, without significantly altering the global electronic features.

To overcome the well-known band-gap underestimation of semilocal functionals, additional calculations were performed using the hybrid HSE06 functional [53]. Without SOC, HSE06 predicts a larger positive value of ΔECBM−VBM=0.23\Delta E_{\mathrm{CBM-VBM}} = 0.23 eV, corresponding to a type-II band alignment, in agreement with previous theoretical studies [50]. When SOC is included, however, the energy separation is substantially reduced to ΔECBM−VBM=0.057\Delta E_{\mathrm{CBM-VBM}} = 0.057 eV, placing the system very close to the type-II/type-III transition. Therefore, although the exact value of ΔECBM−VBM\Delta E_{\mathrm{CBM-VBM}} depends on the exchange-correlation functional, both PBE and HSE06 consistently show that spin–orbit coupling strongly reduces the energy separation between the conduction- and valence-band edges, driving the MoTe2_2/HfS2_2 heterostructure toward the broken-gap regime.

Since the semilocal PBE+SOC calculations predict an intrinsic broken-gap alignment while HSE06+SOC places the system only 57 meV away from this regime, the two approaches lead to the same qualitative physical picture: the MoTe2_2/HfS2_2 heterostructure lies in the immediate vicinity of the type-II/type-III boundary. Consequently, external perturbations such as electric fields, strain, or twist angle are expected to readily tune the system across this boundary, justifying the use of the computationally more efficient PBE+SOC approach to investigate these trends.

The out-of-plane inversion-symmetry breaking induced in 1L–MoTe2_2 by its stacking with 1L–HfS2_2 gives rise to Rashba-type spin splitting in the vicinity of the Γ\Gamma point, where bands associated with opposite spin states are shifted in opposite directions in momentum space. This behavior is analogous to that observed in heavy-metal surfaces [54–56]. Notably, such spin splitting is absent in the isolated MoTe2_2 monolayer and emerges only after the formation of the MoTe2_2/HfS2_2 vdWH, demonstrating that the Rashba effect originates from the interfacial inversion-symmetry breaking combined with strong spin–orbit coupling.

Figure 2(a) presents an enlarged view of the electronic band structure around the Γ\Gamma point, highlighting the Rashba spin splitting along the K–Γ\Gamma high-symmetry path. The characteristic Rashba parameters, namely the momentum offset (kRk_{\mathrm{R}}), the Rashba energy (ERE_{\mathrm{R}}), defined as the energy difference between the band extremum and the spin-degenerate point at Γ\Gamma, and the Rashba coefficient (αR=2ER/kR\alpha_{\mathrm{R}} = 2E_{\mathrm{R}}/k_{\mathrm{R}}), are also indicated. The calculated values are kR=0.136k_{\mathrm{R}} = 0.136 Å−1^{-1}, ER=17.256E_{\mathrm{R}} = 17.256 meV, and αR=0.254\alpha_{\mathrm{R}} = 0.254 eV·Å. These values lie within the range reported for TMD-based vdW heterostructures [15, 16], are comparable to those observed for Au(111) surfaces [54], and are significantly larger than those reported for the InGaAs/InAlAs quantum well [57]. Enlarged views of the Rashba-split bands around the Γ\Gamma point for the remaining stacking configurations, together with the corresponding values of kRk_{\mathrm{R}}, ERE_{\mathrm{R}}, and αR\alpha_{\mathrm{R}}, are presented in Figure S10–(Figure S10) and Table S3 of the Supporting Information (SI) [49], respectively.

Rashba spin splitting and spin textures for the MoTe$_2$/HfS$_2$ vdWH–IV heterostructure

Figure 2. (Color online) (a) Rashba spin splitting around the Γ\Gamma point for the most stable MoTe2_2/HfS2_2 vdWH–IV heterostructure. The Rashba maximum momentum offset (kRk_R) and the energy difference between the band’s extreme and the degenerate Γ\Gamma point of the band (ERE_R) are indicated by the black arrows, while the green dashed line marks the constant-energy cut (EcutE_{\mathrm{cut}}). (b) Spin polarization components SxS_x, SyS_y, and SzS_z evaluated on the constant-energy contour in momentum space. The color scale represents the magnitude and sign of the spin polarization. (c) Corresponding spin textures in the kxk_x–kyk_y plane, showing the Rashba-type helical spin-momentum locking induced by inversion symmetry breaking.

Zoomed-in band structures around the $\Gamma$ point for the MoTe$_2$/HfS$_2$ heterostructure under different stacking configurations

Figure S10. Zoomed-in band structures around the Γ\Gamma point for the MoTe2_2/HfS2_2 heterostructure under different stacking configurations (vdWH-I to vdWH-VI), calculated using PBE including spin–orbit coupling (PBE+SOC). The valence bands exhibit a clear Rashba-type spin splitting, characterized by momentum-offset parabolic dispersions near Γ\Gamma. The magnitude of the splitting and band curvature depend on the stacking configuration, reflecting variations in interlayer interaction and symmetry breaking.

Figure 2(b) shows the spin-polarization components SxS_x, SyS_y, and SzS_z calculated on a constant-energy contour (EcutE_{\mathrm{cut}}), defined by the green horizontal line in Figure 2(a), while Figure 2(c) displays the corresponding spin texture in reciprocal space. The in-plane components, SxS_x and SyS_y, exhibit a characteristic helical spin arrangement, whereas the color scale indicates the degree of spin polarization. The spin polarization is considerably stronger within the plane (x,yx,y), where two approximately circular contours can be identified around the Γ\Gamma point. These inner and outer contours exhibit opposite spin helicities, with clockwise and counterclockwise spin rotations, respectively. They correspond to the Rashba-split bands and provide clear evidence of spin–momentum locking. In contrast, the out-of-plane component, SzS_z, shows a non-zero but considerably weaker signal than the in-plane components. This residual out-of-plane spin polarization can be attributed to the crystal symmetry of the heterostructure and the strong spin–orbit coupling primarily associated with the MoTe2_2 layer. These results suggest that the MoTe2_2/HfS2_2 vdWH is a promising platform for spintronic devices based on electrical control of spin degrees of freedom.

It is worth noting that type-III vdWHs may exhibit negative differential resistance (NDR) arising from BTBT processes [11, 19, 21] [58, 59]. To further elucidate the physical mechanism associated with the broken-gap band alignment, we constructed the schematic representation shown in Figure 3(a).

Schematic band alignment, electrostatic potential, and charge-density difference of the MoTe2/HfS2 heterostructure

Figure 3. (Color online) (a) Schematic band alignment of the MoTe2_2/HfS2_2 heterostructure before and after contact, referenced to the vacuum level. The work functions, conduction-band offset (ΔECBM\Delta E_{\mathrm{CBM}}), and valence-band offset (ΔEVBM\Delta E_{\mathrm{VBM}}) are indicated, evidencing a broken-gap type–III band alignment and the possibility of band-to-band tunneling (BTBT). (b) Planar-averaged electrostatic potential along the out-of-plane direction (zz) for the MoTe2_2/HfS2_2 vdWH, showing the potential difference (ΔV\Delta V) between the layers. (c) Three-dimensional charge-density-difference isosurface of the heterostructure, illustrating charge transfer from MoTe2_2 to HfS2_2 and the resulting built-in electric field. Red and black isosurfaces represent charge accumulation and depletion, respectively. (d) Plane-averaged charge-density difference Δρ(z)\Delta\rho(z) along the zz direction, highlighting the interfacial charge redistribution between the MoTe2_2 and HfS2_2 layers.

The work function, which serves as an intrinsic reference for band alignment, is defined as W=Evac−EFW = E_{\mathrm{vac}} - E_{\mathrm{F}}, where EvacE_{\mathrm{vac}} and EFE_{\mathrm{F}} denote the vacuum level and Fermi level, respectively. As shown in Figure 3(a), the conduction-band offset between the HfS2_2 and MoTe2_2 monolayers is ΔEC=1.32\Delta E_{\mathrm{C}} = 1.32 eV, while the corresponding valence-band offset is ΔEV=1.39\Delta E_{\mathrm{V}} = 1.39 eV. Before heterostructure formation, the calculated work functions of 1L–MoTe2_2 and 1L–HfS2_2 are 4.56 and 5.89 eV, respectively.

Upon formation of the heterostructure, spontaneous charge transfer occurs from the MoTe2_2 layer to the HfS2_2 layer owing to the difference in their work functions, giving rise to an electrostatic potential difference of ΔV=6.42\Delta V = 6.42 eV, as illustrated in Figure 3(b). As a consequence, the Fermi level of the heterostructure shifts to a position located below the CBM of HfS2_2 and above the VBM of MoTe2_2. The resulting work function of the vdWH is 5.18 eV, which is higher than that of isolated MoTe2_2 and slightly lower than that of isolated HfS2_2. Consequently, the heterostructure exhibits a type-III (broken-gap) band alignment, enabling efficient electron tunneling from the VBM of MoTe2_2 to the CBM of HfS2_2, which is the hallmark of the BTBT mechanism. This characteristic makes the MoTe2_2/HfS2_2 heterostructure particularly attractive for TFETs applications.

To gain deeper insight into the interlayer coupling mechanism and charge redistribution in the MoTe2_2/HfS2_2 vdWH, we calculated both the three-dimensional (3D) charge-density-difference isosurface [Figure 3(c)] and the planar-averaged charge-density difference along the cc direction [Figure 3(d)]. The planar-averaged charge-density difference is defined as

Δρ(z)=ΔρMoTe2/HfS2−ΔρHfS2−ΔρMoTe2,(1)\Delta\rho(z) = \Delta\rho_{\mathrm{MoTe_2/HfS_2}} - \Delta\rho_{\mathrm{HfS_2}} - \Delta\rho_{\mathrm{MoTe_2}}, \tag*{(1)}

where ΔρMoTe2/HfS2\Delta\rho_{\mathrm{MoTe_2/HfS_2}} denotes the charge density of the MoTe2_2/HfS2_2 heterostructure, while ΔρHfS2\Delta\rho_{\mathrm{HfS_2}} and ΔρMoTe2\Delta\rho_{\mathrm{MoTe_2}} correspond to the charge densities of the isolated 1L–HfS2_2 and 1L–MoTe2_2 monolayers, respectively.

The 3D charge-density-difference isosurface shown in Figure 3(c) reveals a net charge transfer from the MoTe2_2 layer to the HfS2_2 layer. The red and black regions indicate electron accumulation and depletion, respectively. Consistently, the planar-averaged charge-density difference displayed in Figure 3(d) shows that the charge redistribution occurs predominantly between the Te atoms of the MoTe2_2 layer and the adjacent S atoms of the HfS2_2 layer.

To quantitatively evaluate this process, Bader charge analysis was performed. The calculated charge transfer associated with each atomic species is Hf(−2.016e-2.016e), S(+2.055e+2.055e), Mo(−0.490e-0.490e), and Te(+0.451e+0.451e), where positive and negative values denote electron gain and loss, respectively. As a result, a net charge transfer of Δq=0.039e\Delta q = 0.039e per unit cell occurs from the MoTe2_2 layer to the HfS2_2 layer, a value comparable to those reported for other TMD-based van der Waals heterostructures [10, 11, 17, 19]. This interfacial charge redistribution allows the MoTe2_2/HfS2_2 vdWH to be viewed as a nanoscale parallel-plate capacitor, generating an intrinsic electric field directed from the MoTe2_2 layer toward the HfS2_2 layer.

We now turn our attention to the twisted MoTe2_2/HfS2_2 heterostructure (t-MoTe2_2/HfS2_2). Twisted TMD-based systems have attracted considerable interest in recent years owing to their rich electronic properties and the emergence of Moiré-driven phenomena [60–63]. Moreover, recent advances in fabrication techniques have made the experimental realization of twisted van der Waals devices increasingly feasible. Motivated by these developments, we next investigate the structural and electronic properties of the tt–MoTe2_2/HfS2_2 heterostructure.

Four twisted MoTe2_2/HfS2_2 heterostructures were constructed from the equilibrium vdWH by employing the coincidence-site lattice [64, 65] approach described above. For each commensurate supercell, the twist angle is uniquely determined by an integer pair (m,n)(m,n), which defines the coincidence lattice vectors and, consequently, the size of the Moiré supercell. Owing to the hexagonal symmetry of the heterostructure, several commensurate Moiré superlattices can be generated following this construction, as previously demonstrated for twisted boron arsenide bilayers (tt–BAs) and other van der Waals materials [37, 39, 65, 66]. To ensure computational feasibility, only supercells containing fewer than 150 atoms (Natom<150N_{\mathrm{atom}} < 150) were considered. The selected commensurate structures correspond to the integer pairs (m,n)=(2,3)(m,n) = (2,3), (1,2)(1,2), (1,3)(1,3), and (1,4)(1,4), yielding twist angles of θ=13.17∘\theta= 13.17^\circ, 21.79∘21.79^\circ, 32.20∘32.20^\circ, and 38.21∘38.21^\circ, respectively. These structures contain 114, 42, 78, and 126 atoms per supercell.

Figure 4(a) shows the Moiré superlattice corresponding to θ=21.79∘\theta= 21.79^\circ, where the black rhombus highlights the supercell. The remaining twisted structures are presented in Figure S4 of the SI [49]. Full structural relaxations, including both atomic positions and lattice parameters, were performed for all twisted heterostructures. The resulting interlayer distances are 3.359 Å (θ=13.17∘\theta= 13.17^\circ), 3.387 Å (θ=21.79∘\theta= 21.79^\circ), 3.415 Å (θ=32.20∘\theta= 32.20^\circ), and 3.403 Å (θ=38.21∘\theta= 38.21^\circ). These values are slightly larger than that obtained for the untwisted heterostructure, reflecting the influence of Moiré-induced structural relaxation, in agreement with previous reports on twisted van der Waals systems [39, 65, 66].

Twisted MoTe2/HfS2 heterostructure, electronic band structure, and charge-density difference

Figure 4. (Color online) (a) Top view of the twisted MoTe2_2/HfS2_2 heterostructure (t-MoTe2_2/HfS2_2) with a rotation angle of θ=21.79∘\theta= 21.79^\circ, highlighting the moiré supercell (dark rhombus). (b) Electronic band structure of the twisted system, calculated using the PBE+SOC, showing contributions from MoTe2_2 (blue) and HfS2_2 (green). (c)–(d) Three-dimensional charge density difference of the twisted heterostructure, illustrating the spatial modulation induced by the moiré pattern, where red and black isosurfaces indicate charge accumulation and depletion, respectively. The isosurface value is set to 2.5×10−42.5 \times10^{-4} eÅ−3^{-3}.

Top views of twisted MoTe2/HfS2 heterostructures for different commensurate twist angles

Figure S4. Top views of the twisted MoTe2/HfS2\mathrm{MoTe}_{2}/\mathrm{HfS}_{2} heterostructures (tt-MoTe2/HfS2\mathrm{MoTe}_{2}/\mathrm{HfS}_{2}) for different commensurate twist angles: (a) θ=13.17∘\theta= 13.17^\circ, (b) θ=21.79∘\theta= 21.79^\circ, (c) θ=32.20∘\theta= 32.20^\circ, and (d) θ=38.21∘\theta= 38.21^\circ. The black rhombus in each panel highlights the corresponding moiré supercell. Yellow, green, brown, and blue spheres represent S, Hf, Te, and Mo atoms, respectively.

The electronic band structures of the twisted MoTe2_2/HfS2_2 heterostructures calculated within the PBE+SOC framework are presented in Figure S11 of the Supplementary Information (SI) [49]. For all twist angles, the orbital-projected band structures reveal that the conduction-band minimum (CBM) remains predominantly derived from the HfS2_2 layer (green), whereas the valence-band maximum (VBM) is mainly contributed by the MoTe2_2 layer (blue). Among the investigated structures, the twist angles θ=21.79∘\theta= 21.79^\circ [Fig. 4(b)] and θ=32.20∘\theta= 32.20^\circ [Fig. S11(c) of the SI] [49] exhibit the smallest energy separations between the CBM and VBM, with ΔECBM−VBM=4\Delta E_{\mathrm{CBM-VBM}} = 4 and 12 meV, respectively, placing these systems at the verge of the transition between the type-II and type-III (broken-gap) band-alignment regimes. In contrast, the twisted structures with θ=13.17∘\theta= 13.17^\circ and 38.21∘38.21^\circ [Figs. S11(a) and S11(d) of the SI] [49] display larger negative values of ΔECBM−VBM\Delta E_{\mathrm{CBM-VBM}}, corresponding to a more pronounced type-III band alignment. These results demonstrate that twist-angle engineering provides an effective strategy for continuously tuning the band-edge alignment while preserving the spatial separation of electrons and holes across the MoTe2_2/HfS2_2 interface.

PBE+SOC electronic band structures of twisted MoTe$_2$/HfS$_2$ heterostructures for twist angles of (a) 13.17°, (b) 21.79°, (c) 32.20°, and (d) 38.21°

Figure S11. PBE+SOC electronic band structures of twisted MoTe2_2/HfS2_2 heterostructures for twist angles of (a) 13.17∘13.17^\circ, (b) 21.79∘21.79^\circ, (c) 32.20∘32.20^\circ, and (d) 38.21∘38.21^\circ. Blue and green colors denote the projected contributions from the MoTe2_2 and HfS2_2 layers, respectively. The Fermi energy is set to zero. The band alignment remains governed by the MoTe2_2 valence states and HfS2_2 conduction states, while the relative CBM–VBM energy offset is strongly modulated by the twist angle.

Figures 4(c)–(d) present the charge-density difference of the twisted heterostructure, where the red and black regions indicate electron accumulation and depletion, respectively. Similar to the untwisted MoTe2_2/HfS2_2 vdWH, charge transfer occurs from the MoTe2_2 layer to the HfS2_2 layer. Bader charge analysis reveals a net charge transfer of approximately Δq=0.236e\Delta q = 0.236e per supercell, substantially larger than that obtained for the untwisted heterostructure. Owing to the high computational cost associated with twisted Moiré superlattices, the effects of external electric fields as well as out-of-plane and in-plane strain are investigated only for the θ=21.79∘\theta= 21.79^\circ configuration in the following sections.

Electronic properties under an applied vertical electric field

Gate-voltage modulation is one of the most widely employed approaches in experimental studies and practical electronic devices, providing an effective route for tuning the electronic properties of low-dimensional materials [37, 67–70]. Such an approach enables the controlled manipulation of electronic characteristics to meet the requirements of different technological applications. Motivated by this capability, we investigate the effects of an external vertical electric field (EextE_{\mathrm{ext}}) on the electronic properties of both the MoTe2_2/HfS2_2 vdWH and the twisted heterostructure tt–MoTe2_2/HfS2_2.

The external electric field is applied perpendicular to the stacked layers and was included in both the structural relaxation and electronic-structure calculations, following methodologies previously reported in the literature [12, 15, 16] [69]. A positive electric field (Eext>0E_{\mathrm{ext}} > 0) is defined in the direction from the MoTe2_2 layer to the HfS2_2 layer, while a negative field (Eext<0E_{\mathrm{ext}} < 0) is applied in the opposite direction, from HfS2_2 to MoTe2_2. The positive EextE_{\mathrm{ext}} has the same direction as the internal electric field, generated by the interfacial charge transfer between the layers, and thus the internal electric field is intensified. In contrast, for Eext<0E_{\mathrm{ext}} < 0, the internal electric field is partially attenuated. The external electric field values considered ranged from −5-5 V/nm to 5 V/nm.

Figures 5(a)–(e) display the electronic band structures of the MoTe2_2/HfS2_2 vdWH under external vertical electric fields, calculated within the PBE+SOC framework. For positive electric fields [Figs. 5(d)–(e)], the CBM associated with the HfS2_2 layer (green bands) shifts toward lower energies relative to the Fermi level, whereas the VBM derived from the MoTe2_2 layer (blue bands) moves toward higher energies. As a consequence, the energy difference between the CBM and VBM decreases from −0.11-0.11 eV at Eext=3E_{\mathrm{ext}} = 3 V/nm to −0.15-0.15 eV at Eext=5E_{\mathrm{ext}} = 5 V/nm. The increasingly negative values of ΔECBM−VBM\Delta E_{\mathrm{CBM-VBM}} indicate an enhanced overlap between the valence- and conduction-band edges, thereby strengthening the BTBT process. Consequently, a larger number of carriers are expected to tunnel from the VBM of MoTe2_2 into the CBM of HfS2_2. Therefore, under positive electric fields, the type–III (broken-gap) band alignment is not only preserved but further reinforced as the field strength increases.

In contrast, an opposite trend is observed for Eext<0E_{\mathrm{ext}} < 0. For Eext=−3E_{\mathrm{ext}} = -3 and −5-5 V/nm, the energy differences be-

Electronic band structures of the twisted t–MoTe$_2$/HfS$_2$ vdWH under different external vertical electric fields

Figure 8. (Color online) Electronic band structures of the twisted t–MoTe2_2/HfS2_2 vdWH calculated using the PBE+SOC approach under different external vertical electric fields, ranging from −5 to 5 V/nm. The blue and green colors represent the contributions from the MoTe2_2 and HfS2_2 layers, respectively.

tween the CBM and VBM are 0.043 and 0.16 eV, respectively, indicating the opening of a finite band gap that increases with the magnitude of the applied electric field. Under these conditions, the heterostructure undergoes a transition from a type–III (broken-gap) to a type–II band alignment. These findings are consistent with previous reports on TMD-based vdWHs exhibiting type–III band alignment [10, 11, 16, 17]. The shift of the band edges can be attributed to the electrostatic potential gradient across the interface induced by the external electric field, which promotes charge redistribution between the two layers. The equilibrium interlayer distance of the most stable heterostructure (vdWH–IV) is approximately 0.32 nm. Therefore, considering the maximum applied field of ±5 V/nm, the corresponding potential difference between the layers is approximately ΔV=±1.6\Delta V = \pm1.6 V. Although this value is relatively large, perpendicular electric fields of comparable or even greater magnitude have already been experimentally achieved in two-dimensional heterostructures through dual ionic gating techniques [71, 72]. These experimental demonstrations indicate that the electric-field regime investigated here lies within experimentally accessible conditions for vdWH-based devices.

Figure 5(f)–(Figure 5j) illustrate the evolution of the Rashba-split bands in the vicinity of the Γ\Gamma point under different external electric fields. The perpendicular electric field strongly affects both the Rashba energy (ERE_\mathrm{R}) and the momentum offset (kRk_\mathrm{R}). For Eext<0E_\mathrm{ext} < 0, the Rashba splitting becomes progressively more pronounced, whereas it is gradually suppressed for Eext>0E_\mathrm{ext} > 0.

Electronic band structures and enlarged views of the MoTe2/HfS2 vdWH under external electric fields

Figure 5. (Color online) (a)–(e) Electronic band structures of the MoTe2_2/HfS2_2 vdWH under external electric fields ranging from −5-5 to 55 V/nm, calculated using the PBE+SOC approach. Panels (f)–(j) show an enlarged view around the Γ\Gamma point, highlighting the Rashba spin splitting. The red dashed line denotes the energy of the Rashba degeneracy point in Γ\Gamma (EΓE_{\Gamma}), while the green dotted line indicates a cutoff energy (EcutE_{\mathrm{cut}}) and ΔE\Delta E is a small energy shift relative to EΓE_{\Gamma}.

The red dashed horizontal line denotes the energy of the Rashba degeneracy point at Γ\Gamma (EΓE_\Gamma), while the green dashed line corresponds to a constant-energy contour defined as Ecut=EΓ+ΔEE_\mathrm{cut} = E_\Gamma+ \Delta E, where ΔE=134.225\Delta E = 134.225 meV is kept fixed for all electric-field values. Besides shifting the Rashba degeneracy point in energy, the external electric field also modifies the curvature and separation of the Rashba-split bands.

field also modifies the curvature and separation of the Rashba-split bands. For Eext=−5E_\mathrm{ext} = -5 V/nm, the Rashba parameters reach ER=30.793E_\mathrm{R} = 30.793 meV, kR=0.161k_\mathrm{R} = 0.161 Å−1^{-1} and αR=0.382\alpha_\mathrm{R} = 0.382 eV·Å, indicating a substantial enhancement of the Rashba effect compared with the field-free case.

To gain further insight into the microscopic origin of this behavior, Figure 6 presents the spin textures of the MoTe2_2/HfS2_2 vdWH under different external electric fields. The first and second rows correspond to the in-plane spin components (SxS_x and SyS_y), whereas the third row displays the out-of-plane component (SzS_z). A clear modification of the spin texture is observed upon reversing the direction of the applied electric field. For Eext=−5E_\mathrm{ext} = -5 V/nm, the SxS_x component exhibits a well-defined helical spin rotation. When the field is reversed to Eext=+5E_\mathrm{ext} = +5 V/nm, the helicity is preserved, while the spin polarization is inverted, as evidenced by the interchange of the red and blue regions. In contrast, the SyS_y and SzS_z components display similar rotational patterns and spin polarizations for both field directions. These results demonstrate that the external electric field enables an efficient modulation of the Rashba spin texture. Furthermore, the spin polarization is slightly stronger for Eext<0E_\mathrm{ext} < 0 than for Eext>0E_\mathrm{ext} > 0, in agreement with the larger Rashba splitting observed under negative electric fields.

Figure 6. (Color online) Spin textures of the MoTe2_2/HfS2_2 vdWH under external electric fields of −5-5, 00, and 55 V/nm. The first, second, and third rows correspond to the spin projections SxS_x, SyS_y, and SzS_z, respectively. The arrows indicate the in-plane and out-of-plane spin components, while the color scale represents the magnitude and sign of the spin polarization, around the Γ\Gamma point.

Figure 7 summarizes the evolution of the band alignment and charge transfer in the MoTe2_2/HfS2_2 vdWH as a function of the external electric field. The blue curve represents the energy difference between the HfS2_2-derived CBM and the MoTe2_2-derived VBM, ΔECBM−VBM\Delta E_{\mathrm{CBM-VBM}}, while the red curve corresponds to the Bader charge transfer (Δq\Delta q) between the two layers.

Figure 7. (Color online) Electric-field dependence of the band alignment and charge transfer in the MoTe2_2/HfS2_2 vdWH. The blue curve (left axis) shows the energy difference ΔECBM−VBM\Delta E_{\mathrm{CBM-VBM}}, while the red curve (right axis) represents the Bader charge transfer Δq\Delta q. The shaded regions indicate the transition between type–II (light blue) and type–III (light orange) band alignment. Δq\Delta q is charge transfer from the MoTe2_2 layer to the HfS2_2 layer.

A nearly linear variation of ΔECBM−VBM\Delta E_{\mathrm{CBM-VBM}} is observed with increasing electric field. For negative fields, ΔECBM−VBM\Delta E_{\mathrm{CBM-VBM}} remains positive, indicating a type–II band alignment. In this regime, the electronic states remain energetically separated, reducing the overlap between the valence- and conduction-band edges and consequently suppressing interlayer tunneling. As the electric field increases toward positive values, ΔECBM−VBM\Delta E_{\mathrm{CBM-VBM}} decreases continuously and becomes negative at approximately Eext≈−1.8E_{\mathrm{ext}} \approx-1.8 V/nm. This behavior signals a gradual transition from a type–II to a type–III (broken-gap) band alignment, enhancing the overlap between the MoTe2_2-derived VBM and the HfS2_2-derived CBM and thereby favoring band-to-band tunneling processes.

In addition, the charge transfer Δq\Delta q increases monotonically with the external electric field. This trend reflects the progressive enhancement of interfacial charge redistribution induced by the applied field and is fully consistent with the increasing asymmetry observed in both the electronic band structures and the Rashba spin textures. For Eext>0E_{\mathrm{ext}} > 0, the larger charge transfer is directly associated with the strengthening of the type–III band alignment, which favors band-to-band tunneling and enhances the interlayer coupling. This behavior arises because the external electric field is aligned with the intrinsic electric field generated by interfacial charge transfer, thereby amplifying the charge separation across the interface and strengthening the electrostatic interaction between the two layers. Consequently, the increased interfacial charge density modifies the electronic transport properties of the heterostructure [19] [73] and further enhances the overlap between the MoTe2_2-derived VBM and the HfS2_2-derived CBM, reinforcing the broken-gap character of the system.

The correlation between the increase in Δq\Delta q, the enhanced CBM–VBM overlap, and the modulation of the spin texture demonstrates that the external electric field simultaneously affects the orbital, charge, and spin degrees of freedom of the vdWH. These results highlight the remarkable electrostatic tunability of the MoTe2_2/HfS2_2 heterostructure, enabling electrical control of both the transition between type–II and type–III band-alignment regimes and the Rashba spin splitting. Such characteristics are highly desirable for the development of low-power TFET and spintronic devices.

Figures 8(a)–(e) present the electronic band structures of the twisted heterostructure t–MoTe2_2/HfS2_2 (θ=21.79∘\theta= 21.79^\circ) under different external electric fields. Similar to the untwisted system, the electric field strongly modifies the relative positions of the MoTe2_2- and HfS2_2-derived band edges. For negative electric fields, the HfS2_2-derived CBM remains above the MoTe2_2-derived VBM, corresponding to a type–II band alignment. In contrast, positive electric fields progressively reduce the energy difference ΔECBM−VBM\Delta E_{\mathrm{CBM-VBM}}, eventually driving the system into the type–III (broken-gap) regime. Notably, this transition occurs in the vicinity of Eext≈0E_{\mathrm{ext}} \approx0 V/nm, indicating that the twisted heterostructure lies intrinsically close to the type–II/type–III boundary.

The quantitative evolution of this behavior is summarized in Figure 9. The value of ΔECBM−VBM\Delta E_{\mathrm{CBM-VBM}} decreases nearly monotonically with increasing electric field, changing from approximately 0.310.31 eV at Eext=−5E_{\mathrm{ext}} = -5 V/nm to about −0.10-0.10 eV at Eext=5E_{\mathrm{ext}} = 5 V/nm. In particular, at zero electric field, ΔECBM−VBM≈0.004\Delta E_{\mathrm{CBM-VBM}} \approx0.004 eV, revealing that the twisted heterostructure is already positioned extremely close to the crossover between type–II and type–III band alignment. This result indicates that twist engineering alone can substantially modify the electronic structure, bringing the system to the verge of a broken-gap configuration.

Figure 9. (Color online) Same as Fig. 6, but for t–MoTe2_2/HfS2_2.

In addition, the Bader charge transfer Δq\Delta q increases significantly with the applied electric field, reflecting an enhanced interfacial charge redistribution. For positive fields, the larger Δq\Delta q is accompanied by a stronger type–III character, which increases the overlap between the MoTe2_2-derived VBM and the HfS2_2-derived CBM. These findings suggest that the combination of twist-angle engineering and electrostatic gating provides an additional degree of freedom for simultaneously controlling the band alignment, charge transfer, and interlayer coupling in t–MoTe2_2/HfS2_2. Consequently, twisted MoTe2_2/HfS2_2 heterostructures emerge as attractive platforms for tunable tunneling electronic devices.

Electronic properties under an out-of-plane and in-plane strain

Strain engineering has emerged as an effective strategy for tuning the electronic properties of two-dimensional (2D) materials and van der Waals heterostructures (vdWHs) [36, 74]. Unlike conventional bulk materials, 2D systems can sustain relatively large deformations without structural failure, allowing substantial modifications of the electronic band structure, interlayer coupling, and charge transfer even under moderate strain [38]. In particular, both out-of-plane and in-plane strain have been shown to efficiently control the band alignment and electronic properties of TMD-based vdWHs [10, 11, 12, 16, 17]. Motivated by these findings, we investigate the effects of out-of-plane and in-plane strain on the electronic properties of the MoTe2_2/HfS2_2 heterostructures, considering both the untwisted configuration and the twisted system with a twist angle of θ=21.79∘\theta= 21.79^\circ.

To simulate out-of-plane strain in both heterostructures, the zz coordinates of the interfacial atoms were constrained, namely the upper Te atoms of the bottom layer and the lower S atoms of the top layer. The in-plane coordinates of these atoms, together with the positions of all remaining atoms, were allowed to fully relax during the structural optimization. The equilibrium configuration was used as the reference structure, and the interlayer distance was varied within the range Δd=±0.5\Delta d = \pm0.5 Å. Negative and positive values of Δd\Delta d correspond to compressive and tensile out-of-plane strain, respectively.

Figure 10 presents the electronic band structures of the heterostructures under out-of-plane strain. Figure 10(a)–(Figure 10e) show the results for the MoTe2_2/HfS2_2 vdWH. For all investigated values of Δd\Delta d, the heterostructure retains its type–III band alignment. Under tensile strain (Δd>0\Delta d > 0), the MoTe2_2-derived VBM at the K point shifts slightly toward lower energies, whereas the HfS2_2-derived CBM at the M point moves upward relative to the Fermi level. As a result, the magnitude of the CBM–VBM overlap decreases with increasing interlayer separation. In addition, the Rashba-split bands around the Γ\Gamma point become progressively less pronounced as the tensile strain increases.

Electronic band structures of the MoTe$_2$/HfS$_2$ vdWH under out-of-plane strain

Figure 10. (Color online) Electronic band structures of the MoTe2_2/HfS2_2 vdWH under out-of-plane strain Δd\Delta d, calculated using the PBE+SOC approach. Panels (a)–(e) correspond to the non-rotated heterostructure, while panels (f)–(j) show the twisted heterostructure. Negative and positive values of Δd\Delta d represent compressive and tensile out-of-plane strain, respectively. The blue and green curves indicate the contributions from the MoTe2_2 and HfS2_2 layers, respectively.

In contrast, compressive strain (Δd<0\Delta d < 0) produces the opposite effect. The MoTe2_2-derived VBM shifts toward higher energies, while the HfS2_2-derived CBM moves downward, approaching and eventually crossing the Fermi level for the largest compressive strains considered. Simultaneously, the Rashba-split bands undergo a substantial energy shift toward the Fermi level, reaching it for the maximum compression investigated. Consequently, the CBM–VBM overlap increases under compressive strain, strengthening the type–III (broken-gap) character of the heterostructure. This behavior is expected to enhance the BTBT process by widening the tunneling window and increasing the number of available tunneling channels.

Figure 10(f)–(Figure 10j) present the electronic band structures of the tt–MoTe2_2/HfS2_2 heterostructure under out-of-plane strain. For tensile strain (Δd>0\Delta d > 0), a behavior similar to that observed for the untwisted MoTe2_2/HfS2_2 vdWH is found. However, the twisted heterostructure preserves its type–III (broken-gap) band alignment throughout the entire strain range considered. At the same time, the magnitude of the CBM–VBM overlap gradually decreases as the interlayer separation increases.

A markedly different behavior is observed under compressive strain (Δd<0\Delta d < 0). In this case, the MoTe2_2-derived VBM at the K point shifts toward lower energies, whereas the HfS2_2-derived CBM at the M point moves upward relative to the Fermi level. As a consequence, the overlap between the CBM and VBM progressively decreases, eventually leading to the opening of a finite band gap. In addition, the Rashba-split bands undergo a substantial energy shift toward the Fermi level as the compression increases. These results are qualitatively consistent with previous studies on twisted TMD-based heterostructures exhibiting type–III band alignment [12, 16]. Overall, the results indicate a gradual transition from a type–III to a type–II band alignment, demonstrating that compressive out-of-plane strain provides an efficient mechanism for tuning the electronic structure of the twisted heterostructure.

Figure 11(a)–(Figure 11b) show the binding energy (EbE_b) and the Bader charge transfer (Δq\Delta q) as a function of out-of-plane strain for the MoTe2_2/HfS2_2 vdWH and the tt–MoTe2_2/HfS2_2 heterostructure, respectively. In both systems, Δq\Delta q exhibits a monotonic behavior, indicating charge transfer from the MoTe2_2 layer to the HfS2_2 layer. Under compressive strain (Δd<0\Delta d < 0), the charge transfer increases owing to the reduced interlayer separation, which enhances the electronic interaction and orbital hybridization between the two layers. In contrast, tensile strain (Δd>0\Delta d > 0) weakens the interlayer coupling and consequently reduces the charge transfer. Furthermore, the negative values of EbE_b throughout the investigated strain range confirm the structural stability of both heterostructures.

Binding energy and Bader charge transfer of the MoTe2/HfS2 van der Waals heterostructures under out-of-plane and in-plane strain

Figure 11. (Color online) Binding energy and Bader charge transfer of the MoTe2_2/HfS2_2 van der Waals heterostructures under out-of-plane and in-plane strain. Panels (a) and (b) show the dependence of the binding energy (EbE_b) and charge transfer (Δq\Delta q) on the interlayer distance for the non-rotated and twisted (θ=21.79∘\theta= 21.79^\circ) heterostructures, respectively, under out-of-plane strain. Panels (c) and (d) display the strain energy and Bader charge transfer as a function of the biaxial in-plane strain ε\varepsilon for the non-rotated and twisted heterostructures, respectively. The blue solid curves (left axis) represent the binding/strain energy, while the red dashed curves (right axis) correspond to the Bader charge transfer. The shaded blue and red regions indicate compressive and tensile strain regimes, respectively. The vertical dashed lines mark the equilibrium interlayer distance or the strain-free configuration. The schematic illustrations depict the compression and stretching processes applied perpendicular and parallel to the layers.

We now discuss the effects of biaxial strain on the electronic properties of the MoTe2_2/HfS2_2 vdWH and the tt–MoTe2_2/HfS2_2 heterostructure. The biaxial strain is defined as ε=(a−a0)/a0×100%\varepsilon= (a-a_0)/a_0 \times100\%, where aa and a0a_0 denote the lattice parameters of the strained and equilibrium structures, respectively. Positive (negative) values of ε\varepsilon correspond to tensile (compressive) strain, and strain values ranging from ε=−5%\varepsilon= -5\% to +5%+5\% were considered. For each strain value, the lattice parameters were fixed, while all internal atomic coordinates were fully relaxed until the convergence criteria were satisfied.

Figure 12(a)–(Figure 12e) present the electronic band structures of the MoTe2_2/HfS2_2 vdWH under different values of in-plane biaxial strain. As the tensile strain increases (ε>0\varepsilon> 0), the MoTe2_2-derived VBM at the K point shifts slightly toward lower energies, while the HfS2_2-derived CBM at the M point undergoes an energy shift that progressively reduces the overlap between the valence- and conduction-band edges. As a consequence, a finite band gap opens, driving a transition from the type–III (broken-gap) alignment observed at ε=0%\varepsilon= 0\% to a type–II band alignment under tensile strain. This behavior indicates a gradual suppression of the BTBT probability as the tensile deformation increases.

Electronic band structures of the MoTe$_2$/HfS$_2$ vdWH under biaxial in-plane strain

Figure 12. (Color online) Electronic band structures of the MoTe2_2/HfS2_2 vdWH under biaxial in-plane strain ε\varepsilon, calculated using the PBE+SOC approach. Panels (a)–(e) correspond to the non-rotated heterostructure, while panels (f)–(j) show the twisted heterostructure with twist angle θ=21.79∘\theta= 21.79^\circ. Negative and positive values of ε\varepsilon represent compressive and tensile in-plane strain, respectively. The blue and green curves indicate the contributions from the MoTe2_2 and HfS2_2 layers, respectively.

In contrast, compressive biaxial strain (ε<0\varepsilon< 0) produces the opposite trend. The MoTe2_2-derived VBM at the K point shifts toward higher energies, while the HfS2_2-derived CBM at the M point is displaced in a manner that enhances the overlap between the band edges. For the largest compressive strains considered, the valence- and conduction-band states become strongly overlapped, reinforcing the type–III character of the heterostructure. Consequently, the tunneling window broadens and a larger number of electronic channels become available for transport, thereby favoring BTBT processes.

Figure 12(f)–(Figure 12j) display the electronic band structures of the t–MoTe2_2/HfS2_2 heterostructure under different in-plane biaxial strains. Overall, the twisted system exhibits a behavior qualitatively similar to that of the untwisted vdWH. Under tensile strain (ε>0\varepsilon> 0), the heterostructure undergoes a transition toward a type–II band alignment accompanied by the opening of a finite band gap. Conversely, under compressive strain (ε<0\varepsilon< 0), the type–III (broken-gap) alignment is preserved and progressively strengthened due to the enhanced CBM–VBM overlap. These results demonstrate that biaxial strain provides an effective route for controlling the band alignment and tunneling characteristics of both the untwisted and twisted MoTe2_2/HfS2_2 heterostructures.

Consequently, for ε>0\varepsilon> 0, both heterostructures exhibit a type–II band alignment, in which electrons and holes tend to localize in different layers. Such spatial separation of charge carriers is particularly attractive for optoelectronic and photovoltaic applications, as it promotes the dissociation of photoexcited electron–hole pairs, suppresses carrier recombination, and can enhance the efficiency of energy-conversion processes. In contrast, for ε<0\varepsilon< 0, the strengthening of the type–III (broken-gap) band alignment makes these heterostructures promising candidates for band-to-band tunneling devices, such as low-power tunnel field-effect transistors (TFETs).

The strain energy (ESE_S) was calculated according to

ES=(Estrain−Eunstrain)/NE_S = (E_{\mathrm{strain}} - E_{\mathrm{unstrain}})/N,

where EstrainE_{\mathrm{strain}} and EunstrainE_{\mathrm{unstrain}} are the total energies of the strained and equilibrium structures, respectively, and NN is the total number of atoms in the heterostructure. Figure 11(c)–(Figure 11d) display the strain energy ESE_S (blue curve, left axis) together with the Bader charge transfer Δq\Delta q (red curve, right axis), which quantifies the electron transfer from the MoTe2_2 layer to the HfS2_2 layer.

For both heterostructures, the strain energy exhibits an approximately quadratic dependence on ε\varepsilon, characteristic of elastic deformation. The charge transfer Δq\Delta q also displays a clear monotonic dependence on the applied strain. Under compressive strain (ε<0\varepsilon< 0), Δq\Delta q increases, indicating enhanced electron transfer from MoTe2_2 to HfS2_2. Conversely, as the strain shifts toward the tensile regime (ε>0\varepsilon> 0), the charge transfer gradually decreases. These trends are consistent with the evolution of the interlayer coupling and band alignment discussed above. Overall, the obtained results are in good qualitative agreement with previous studies on strained TMD–based van der Waals heterostructures [11, 12, 15, 16, 17].

Conclusions

In this work, we performed a comprehensive first-principles investigation of the structural, electronic, charge-transfer, and spin-related properties of MoTe2_2/HfS2_2 van der Waals heterostructures, including the effects of stacking configuration, external electric fields, twist angle, and mechanical strain. Our calculations reveal that the most stable stacking configuration lies in close proximity to the type-II/type-III (broken-gap) band-alignment boundary. Semilocal PBE+SOC calculations predict an intrinsic broken-gap alignment arising from the overlap between the MoTe2_2-derived valence-band maximum and the HfS2_2-derived conduction-band minimum, whereas HSE06+SOC calculations yield a small positive band gap, indicating that the heterostructure remains very close to the broken-gap regime. The spontaneous interlayer charge transfer generates an intrinsic electric field that breaks inversion symmetry and induces a pronounced Rashba spin splitting around the Γ\Gamma point, accompanied by a characteristic helical spin texture.

We further demonstrate that the electronic and spin properties of the heterostructure can be efficiently tailored by external perturbations. Vertical electric fields modulate the charge transfer, Rashba splitting, and band alignment, driving reversible transitions between type–II and type–III regimes. Twist engineering places the heterostructure close to the boundary between these two regimes, making its electronic structure highly sensitive to external stimuli. Mechanical strain provides an additional degree of control: out-of-plane and biaxial compressive strain enhance the broken-gap character and favor band-to-band tunneling, whereas tensile strain promotes a type–II alignment that is attractive for optoelectronic and photovoltaic applications.

Overall, our results establish MoTe2_2/HfS2_2 heterostructures as highly tunable multifunctional platforms in which charge transfer, band alignment, and Rashba spin splitting can be controlled in a coordinated manner through electrostatic gating, twist angle, and strain engineering. The coexistence of electrically tunable Rashba spin textures and controllable broken-gap electronic structures highlights the potential of these systems for next-generation low-power TFETs, spintronic devices, and multifunctional nanoelectronic technologies.

Acknowledgments

This work was partially supported by the Brazilian agencies CAPES, CNPq, and FAPDF. D.R.C. acknowledges support from CNPq (grants No. 312539/2025–8, No. 437067/2018–1, No. 423423/2021–5, No. 408144/2022–0), the Research Foundation—Flanders (FWO), and the Fundação Cearense de Apoio ao Desenvolvimento Científico e Tecnológico (FUN-CAP). A.C.D. acknowledges support from FAPDF (00193-00001817/2023-43, 00193-00002073/2023-84), CNPq (305174/2023-1, 444069/2024-0, 444431/2024-1), CENAPAD-SP/UNICAMP, the UNICAMP/FINEP-MCTI project, and the NACAD-UFRJ (Lobo Carneiro HPC). T.A.S.P. acknowledges support from the INCT on Materials Informatics (CNPq 371610/2023-0) and FAPEMAT (PRO-2025/00376). T.A.S.P. and A.C.D. also acknowledge PDPG-FAPDF-CAPES Centro-Oeste (00193-00000867/2024-94). This work used resources of the Centro Nacional de Processamento de Alto Desempenho at São Paulo (CENAPAD-SP).

Computational Technical Details

PAW Projectors

Table S1. Basic information on the PAW projectors used in the simulations. The columns list, respectively: the chemical element, its atomic number, the corresponding POTCAR file, the number of valence electrons ZvalZ_{\mathrm{val}}, and the recommended minimum (ENMIN) and maximum (ENMAX) plane-wave cutoff energies.

ElementAtomic numberPOTCARZvalZ_{\mathrm{val}}ENMIN (eV)ENMAX (eV)
Mo42Mo6168.438224.584
Te52Te6131.236174.982
Hf72Hf_pv10165.250220.334
S16S6194.016258.689

Table S1. Basic information on the PAW projectors used in the simulations. The columns list, respectively: the chemical element, its atomic number, the corresponding POTCAR file, the number of valence electrons ZvalZ_{\mathrm{val}}, and the recommended minimum (ENMIN) and maximum (ENMAX) plane-wave cutoff energies.

Crystal Structures

§ Uesugi et al. [1].

† Rimmington & Balchin [2].

The POSCAR file defines the crystal structure, including the lattice vectors, atomic positions, and atomic species corresponding to the stacking configurations investigated. This structural description serves as the basis for the analysis of the twisted MoTe2/HfS2\mathrm{MoTe}_2/\mathrm{HfS}_2 heterostructure.

Listing S1 POSCAR relaxed of vdWH-I stacking.

MoTe2/HfS2 (vdWH-I)
1.00000000000000
3.5664300919000000 0.0000000000000000 0.0000000000000000
-1.7832150459000000 3.0886190604000001 0.0000000000000000
0.0000000000000000 0.0000000000000000 29.6311200240000048
Mo Te Hf S
1 2 1 2
Direct
0.3333330000283397 0.6666669999547707 0.3985937124885197
0.6666669999069086 0.3333329999157186 0.4589276407635055
0.6666669999069086 0.3333329999157186 0.3380413488243406
0.3333332697517051 0.6666665652621262 0.6136242582290379
0.6666662697800447 0.3333335652168969 0.6634943584977933
0.0000002696586137 0.9999995651778448 0.5637740997947134

Listing S2 POSCAR relaxed of vdWH-II stacking.

MoTe2/HfS2 (vdWH-II)
1.00000000000000
3.5664300919000000 0.0000000000000000 0.0000000000000000
-1.7832150459000000 3.0886190604000001 0.0000000000000000
0.0000000000000000 0.0000000000000000 29.6311200240000048
Mo Te Hf S
1 2 1 2
Direct
0.3333330000283397 0.6666669999547707 0.3962044552200581
0.6666669999069086 0.3333329999157186 0.4566671505449804
0.6666669999069086 0.3333329999157186 0.3356878526706737
0.6666665652714698 0.3333331305242524 0.6159586515569586
0.9999995652998095 0.0000001304790231 0.6658129085490998
0.3333335651783784 0.6666661304399710 0.5661244000561467

Listing S3 POSCAR relaxed of vdWH-III stacking.

MoTe2/HfS2 (vdWH-III)
1.00000000000000
3.5664300919000000 0.0000000000000000 0.0000000000000000
-1.7832150459000000 3.0886190604000001 0.0000000000000000
0.0000000000000000 0.0000000000000000 29.6311200240000048
Mo Te Hf S
1 2 1 2
Direct
0.3333330000283397 0.6666669999547707 0.3880934460631522
0.6666669999069086 0.3333329999157186 0.4485967435240710
0.6666669999069086 0.3333329999157186 0.3275554273868835
0.0000000000000000 0.0000000000000000 0.6240483212737900
0.3333330000283397 0.6666669999547707 0.6739304264486066
0.6666669999069086 0.3333329999157186 0.5742310539014071

Listing S4 POSCAR relaxed of vdWH-IV stacking.

1 MoTe2/HfS2 (vdWH-IV)
2 1.00000000000000
3 3.5664300919000000 0.0000000000000000 0.0000000000000000
4 -1.7832150459000000 3.0886190604000001 0.0000000000000000
5 0.0000000000000000 0.0000000000000000 29.6311200240000048
6 Mo Te Hf S
7 1 2 1 2
8 Direct
9 0.3333330000283397 0.6666669999547707 0.3976429149820362
10 0.6666669999069086 0.3333329999157186 0.4580919721487646
11 0.6666669999069086 0.3333329999157186 0.3371280665306529
12 0.0000002697007275 0.0000005651792137 0.6145370652886797
13 0.6666662697800447 0.3333335652168969 0.6644003236079499
14 0.3333342696883221 0.6666675650918776 0.5646550760398412

Listing S5 POSCAR relaxed of vdWH-V stacking.

1 MoTe2/HfS2 (vdWH-V)
2 1.00000000000000
3 3.5664300919000000 0.0000000000000000 0.0000000000000000
4 -1.7832150459000000 3.0886190604000001 0.0000000000000000
5 0.0000000000000000 0.0000000000000000 29.6311200240000048
6 Mo Te Hf S
7 1 2 1 2
8 Direct
9 0.3333330000283397 0.6666669999547707 0.3886191457614032
10 0.6666669999069086 0.3333329999157186 0.4491038828015661
11 0.6666669999069086 0.3333329999157186 0.3280660881065245
12 0.3333335394524255 0.6666671304413399 0.6235065374399582
13 0.9999995395317427 0.0000001304790231 0.6734373578344020
14 0.6666675394400272 0.3333341303540038 0.5737224066540634

Listing S6 POSCAR relaxed of vdWH-VI stacking.

1 MoTe2/HfS2 (vdWH-VI)
2 1.00000000000000
3 3.5664300919000000 0.0000000000000000 0.0000000000000000
4 -1.7832150459000000 3.0886190604000001 0.0000000000000000
5 0.0000000000000000 0.0000000000000000 29.6311200240000048
6 Mo Te Hf S
7 1 2 1 2
8 Direct
9 0.3333330000283397 0.6666669999547707 0.3949377909865248
10 0.6666669999069086 0.3333329999157186 0.4554296925353469
11 0.6666669999069086 0.3333329999157186 0.3343728206108878
12 0.6666669999490225 0.3333339999170875 0.6172641752549950
13 0.3333330000283397 0.6666669999547707 0.6671105303122289
14 0.0000009999366171 0.0000009998297514 0.5673404088979339

Computational Details

All first-principles calculations were performed using the Vienna Ab Initio Simulation Package (VASP) [3, 4, 5, 6, 7] within the projector-augmented wave (PAW) method [8]. The atomic structures of the untwisted MoTe2_2/HfS2_2 van der Waals heterostructures were generated using the PYMATGEN library [9]. Twisted heterostructures were constructed with the TWISTER package [10], which employs the Coincidence Lattice method [11, 12] approach to generate commensurate moiré supercells. In this method, the primitive lattice vectors of the two layers are chosen as

a1(1)=(12,32,0),a2(1)=(−12,32,0),\mathbf{a}^{(1)}_1 = \left(\frac{1}{2},\frac{\sqrt{3}}{2},0\right), \qquad\mathbf{a}^{(1)}_2 = \left(-\frac{1}{2},\frac{\sqrt{3}}{2},0\right),
a1(2)=(1,0,0),a2(2)=(−12,32,0).(2)\mathbf{a}^{(2)}_1 = (1,0,0), \qquad\mathbf{a}^{(2)}_2 = \left(-\frac{1}{2},\frac{\sqrt{3}}{2},0\right). \tag*{(2)}

where superscripts (1) and (2) denote the bottom and top layers, respectively. The coincidence supercell is defined by the lattice vectors

L1=ma1+na2,L2=−na1+(m+n)a2,(3)\mathbf{L}_1 = m\mathbf{a}_1+n\mathbf{a}_2,\qquad\mathbf{L}_2 = -n\mathbf{a}_1+(m+n)\mathbf{a}_2, \tag*{(3)}

with (m,n)(m,n) being integers specifying the commensurate supercell. The corresponding twist angle is given by

cos⁡(θm,n)=n2+4nm+m22(n2+nm+m2),(4)\cos(\theta_{m,n}) = \frac{n^2+4nm+m^2}{2\left(n^2+nm+m^2\right)}, \tag*{(4)}

which generates all commensurate coincidence lattices for hexagonal systems. For a given pair (m,n)(m,n), the number of atoms per unit cell (NatomN_{\mathrm{atom}}) is given by

Natom=4(n2+nm+m2).(5)N_{\mathrm{atom}} = 4(n^2+nm+m^2). \tag*{(5)}

A vacuum region of 20 Å was introduced along the out-of-plane direction to eliminate spurious interactions between periodic images.

For bulk MoTe2_2 and HfS2_2, several exchange–correlation functionals were employed to determine the structural parameters, including PBE [13], PBE+D2 [14, 15], PBE+D3 [16], PBEsol [17], vdW−DF2 [18], and rev−vdW−DF2 [19]. Based on these benchmark calculations, all subsequent simulations for the MoTe2_2/HfS2_2 vdWH and the twisted tt–MoTe2_2/HfS2_2 heterostructure were performed using the PBE+D3 functional, which accounts for van der Waals interactions through semiempirical dispersion corrections.

A plane-wave kinetic-energy cutoff of 500 eV was adopted, corresponding to approximately 2×2\timesENMAX, where ENMAX denotes the largest recommended cutoff energy among the constituent atomic species (see Table S1 in Section I). Structural relaxations and self-consistent field (SCF) calculations for the MoTe2_2/HfS2_2 vdWH (tt–MoTe2_2/HfS2_2) were considered converged when the total-energy variation and residual forces on each atom were smaller than 10−710^{-7} eV (10−510^{-5} eV) and 0.01 eV/Å (0.01 eV/Å), respectively.

Brillouin-zone integrations were carried out using Monkhorst–Pack k-point meshes corresponding to reciprocal-space densities of approximately 50 Å−1^{-1} for structural relaxations and 60 Å−1^{-1} for electronic-structure calculations. For the MoTe2_2/HfS2_2 vdWH, these densities correspond to 16 × 16 × 1 and 19 × 19 × 1 meshes, respectively. For the twisted heterostructure (tt–MoTe2_2/HfS2_2), reciprocal-space densities of approximately 30 Å−1^{-1} and 60 Å−1^{-1} were employed for structural relaxations and electronic calculations, corresponding to 4 × 4 × 1 and 8 × 8 × 1 k-point meshes, respectively. Spin–orbit coupling (SOC) was included in all electronic-structure calculations. To obtain a more accurate description of the electronic properties and to mitigate the well-known band-gap underestimation inherent to semilocal DFT, additional calculations were performed using the hybrid HSE06 functional [20].

For calculations involving external electric fields and planar-averaged electrostatic potentials, dipole corrections were applied along the out-of-plane direction. The thermal stability of the MoTe2_2/HfS2_2 heterostructure was further investigated by ab initio molecular dynamics (AIMD) simulations using a 3 × 3 × 1 supercell and the same computational setup adopted for the twisted heterostructure. The simulations were performed within the canonical (NVT) ensemble at 300 K using the Nosé–Hoover thermostat [21, 22]. The atomic trajectories were propagated for 5 ps with a time step of 1 fs.

Post-processing of the calculated data was carried out using the VASPKIT [23] and PyProcar [24] packages, while atomic structures and charge-density visualizations were generated using the VESTA software [25].

Band structure

Electronic band structures of the MoTe2/HfS2 heterostructure for the six high-symmetry stacking configurations

Figure S8. Electronic band structures of the MoTe2/HfS2\mathrm{MoTe}_{2}/\mathrm{HfS}_{2} heterostructure for the six high-symmetry stacking configurations (vdWH-I to vdWH-VI), calculated within the HSE06 approximation without spin–orbit coupling (SOC).

Electronic band structure of the energetically most stable MoTe₂/HfS₂ heterostructure

Figure S9. Electronic band structure of the energetically most stable MoTe2_2/HfS2_2 heterostructure (vdWH-IV), calculated using the HSE06 hybrid functional including spin–orbit coupling (HSE06+SOC). The orbital-projected bands highlight the contributions from the constituent layers, where the blue and green colors represent states predominantly derived from MoTe2_2 and HfS2_2, respectively.

References

  1. [1]E. Uesugi, X. Miao, H. Ota, H. Goto, and Y. Kubozono, Transistor properties of exfoliated single crystals of 2H–Mo(Se₁₋ₓTeₓ)₂ (0 ≤ x ≤ 1), Phys. Rev. B 95, 245310 (2017).DOI
  2. [2]H. P. B. Rimmington and A. A. Balchin, Crystal data for layer compounds in the series hfsₓse₂₋ₓ, Journal of Materials Science 9, 343 (1974).DOI
  3. [3]G. Kresse and J. Hafner, Ab initio molecular dynamics for open-shell transition metals, Physical Review B 48, 13115 (1993).pubmed.ncbi.nlm.nih.gov/10007687
  4. [4]G. Kresse and J. Hafner, Ab initio molecular-dynamics simulation of the liquid-metal–amorphous-semiconductor transition in germanium, Physical Review B 49, 14251 (1994).pubmed.ncbi.nlm.nih.gov/10010505
  5. [5]G. Kresse and J. Furthmüller, Efficient iterative schemes for ab initio total-energy calculations using a plane-wave basis set, Physical Review B 54, 11169 (1996).pubmed.ncbi.nlm.nih.gov/9984901
  6. [6]G. Kresse and J. Furthmüller, Efficiency of ab-initio total energy calculations for metals and semiconductors using a plane-wave basis set, Computational Materials Science 6, 15 (1996).DOI
  7. [7]G. Kresse and J. Furthmüller, Efficient iterative schemes for ab initio total-energy calculations using a plane-wave basis set, Phys. Rev. B 54, 11169 (1996).pubmed.ncbi.nlm.nih.gov/9984901
  8. [8]P. E. Blöchl, Projector augmented-wave method, Physical Review B 50, 17953 (1994).pubmed.ncbi.nlm.nih.gov/9976227
  9. [9]S. P. Ong, W. D. Richards, A. Jain, G. Hautier, M. Kocher, S. Cholia, D. Günter, V. L. Chevrier, K. A. Persson, and G. Ceder, Python materials genomics (pymatgen): A robust, open-source python library for materials analysis, Computational Materials Science 68, 314 (2013).
  10. [10]S. Naik, M. H. Naik, I. Maity, and M. Jain, Twister: Construction and structural relaxation of commensurate moiré superlattices, Computer Physics Communications 271, 108184 (2022).DOI
  11. [11]D. S. Koda, F. Bechstedt, M. Marques, and L. K. Teles, Coincidence lattices of 2d crystals: Heterostructure predictions and applications, The Journal of Physical Chemistry C 120, 10895 (2016).DOI
  12. [12]K. Uchida, S. Furuya, J.-I. Iwata, and A. Oshiyama, Atomic corrugation and electron localization due to moiré patterns in twisted bilayer graphene, Physical Review B 90, 155451 (2014).DOI
  13. [13]J. P. Perdew, K. Burke, and M. Ernzerhof, Generalized gradient approximation made simple, Physical Review Letters 77, 3865 (1996).pubmed.ncbi.nlm.nih.gov/10062328
  14. [14]S. Grimme, Semiempirical gga-type density functional constructed with a long-range dispersion correction, Journal of Computational Chemistry 27, 1787 (2006).pubmed.ncbi.nlm.nih.gov/16955487
  15. [15]T. Kerber, M. Sierka, and J. Sauer, Application of semiempirical long-range dispersion corrections to periodic systems in density functional theory, Journal of Computational Chemistry 29, 2088 (2008).DOI
  16. [16]S. Grimme, J. Antony, S. Ehrlich, and H. Krieg, A consistent and accurate ab initio parametrization of density functional dispersion correction (dft-d) for the 94 elements h-pu, The Journal of Chemical Physics 132, 154104 (2010).
  17. [17]J. P. Perdew, A. Ruzsinszky, G. I. Csonka, O. A. Vydrov, G. E. Scuseria, L. A. Constantin, X. Zhou, and K. Burke, Restoring the density-gradient expansion for exchange in solids and surfaces, Phys. Rev. Lett. 100, 136406 (2008).pubmed.ncbi.nlm.nih.gov/18517979
  18. [18]K. Lee, E. D. Murray, L. Kong, B. I. Lundqvist, and D. C. Langreth, Higher-accuracy van der waals density functional, Physical Review B 82, 081101 (2010).DOI
  19. [19]I. Hamada, van der waals density functional made accurate, Physical Review B 89, 121103 (2014).DOI
  20. [20]A. V. Krukau, O. A. Vydrov, A. F. Izmaylov, and G. E. Scuseria, Influence of the exchange screening parameter on the performance of screened hybrid functionals, The Journal of Chemical Physics 125, 224106 (2006).pubmed.ncbi.nlm.nih.gov/17176133
  21. [21]S. Nosé, A molecular dynamics method for simulations in the canonical ensemble, Molecular Physics 52, 255 (1984).DOI
  22. [22]W. G. Hoover, Canonical dynamics: Equilibrium phase-space distributions, Phys. Rev. A 31, 1695 (1985).pubmed.ncbi.nlm.nih.gov/9895674
  23. [23]V. Wang, N. Xu, J.-C. Liu, G. Tang, and W.-T. Geng, VASPKIT: A user-friendly interface facilitating high-throughput computing and analysis using VASP code, Computer Physics Communications 267, 108033 (2021).
  24. [24]U. Herath, P. Tavade, X. He, E. Bousquet, S. Singh, F. Muñoz, and A. H. Romero, Pyprocar: A python library for electronic structure pre/post-processing, Computer Physics Communications 251, 107080 (2020).
  25. [25]K. Momma and F. Izumi, VESTA: a three-dimensional visualization system for electronic and structural analysis, Journal of Applied Crystallography 41, 653 (2008).DOI

Paper details

vlnc:W_kemcdfxu
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 3

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents