betaFeedback

WorksPhysics and Astronomy

Resolvent-based estimation of a turbulent wake

Abstract

We present a resolvent-based framework for estimating turbulent velocity fluctuations in the wake of a spanwise-periodic NACA0012 airfoil at Mach 0.3, Reynolds number 23,000, and an angle of attack of 6 degrees. Building on the methodology of Jung et al. (J. Fluid Mech. 2025, vol. 0, A1), we extend the approach to the more complex regime of a turbulent wake, which involves three primary challenges: (1) globally unstable modes in the linearized Navier-Stokes operator, (2) multi-scale turbulent structures, and (3) high-dimensional datasets. To address these challenges, we employ a data-driven approach that constructs causal resolvent-based estimation kernels from cross-spectral densities obtained via large-eddy simulations. These kernels are derived using the Wiener-Hopf method, which optimally enforces causality, thereby enhancing real-time estimation accuracy. The framework captures the spectral signatures of coherent structures and incorporates the colored statistics of nonlinear forcing terms acting on the linear system. To handle the computational demands of the high-dimensional estimation problem, we utilize parallel algorithms developed within the same framework. We further investigate sensor placement by analyzing single-sensor estimation error and coherence with target flow quantities. Results demonstrate accurate causal estimation of streamwise velocity for the spanwise-averaged, spanwise-Fourier-transformed, and mid-span flow using limited shear-stress measurements on the surface of the airfoil. This study underscores the potential of the resolvent-based framework for efficient estimation in compressible, turbulent environments.

Introduction

The estimation of turbulent wakes has been a longstanding focus in fluid mechanics, with decades of experimental and numerical studies revealing their complex dynamics across a range of conditions [18, 44, 19, 49, 20, 46]. At moderate Reynolds numbers (e.g., Re≈20,000Re \approx20{,}000) and mid-range angles of attack (6∘6^\circ–10∘10^\circ), a turbulent wake forms downstream of a laminar separation bubble and exhibits vortex shedding near a characteristic Strouhal number (Stα≈0.2St_\alpha\approx0.2) based on airfoil thickness [13, 56]. Despite the complexity of these flows, even non-physics-based models have successfully estimated key features using experimental data alone [22]. These results motivate the development of estimation methods that are not only accurate and interpretable but also suitable for real-time applications.

Among model-based approaches, resolvent analysis has emerged as a powerful tool for studying and estimating turbulent flow structures. By interpreting the linearized Navier–Stokes equations as a forced system, resolvent analysis identifies the input–output relationships associated with the most amplified flow responses in the frequency domain [24, 40, 51]. This framework has been used to guide both open-loop and closed-loop control designs. For instance, Yeh and Taira [ [56] applied resolvent analysis to identify control parameters for separation control for a NACA airfoil at Re=23,000Re = 23{,}000, Ma=0.3Ma = 0.3, and angles of attack of 6∘6^\circ and 9∘9^\circ. Similarly, Liu et al. [ [34] reduced pressure fluctuations over a cavity using resolvent-informed open-loop control, while Jin et al. [ [23] developed a resolvent-based iterative algorithm for closed-loop estimation and control in cylinder flow.

More recently, resolvent-based estimation techniques have shown strong promise in capturing coherent structures in turbulent flows [52, 38, 2, 1, 58]. These methods leverage the close connection between resolvent modes and spectral proper orthogonal decomposition (SPOD) modes [51], enabling data-informed modeling. However, existing implementations have predominantly relied on non-causal formulations, limiting their utility for real-time estimation and control. To address this, recent work developed causal resolvent-based estimators using the Wiener–Hopf formalism [43], which enforces causality [12, 37] and yields optimal estimation kernels suited for closed-loop control [39] within the incompressible solver Nek5000 [16]. Extending this approach, Jung et al. [ [30] developed an efficient computational implementation integrated into the compressible solver CharLES [Bres et al., 2017], successfully validating causal estimation and control methods for a laminar wake flow. Within the same resolvent-CharLES framework, Towne et al. [ [54] demonstrated the accuracy of linearized Navier–Stokes operators for various flows, leveraging methods proposed by Nielsen and Kleb [ [42] and Bhagwat [ [6].

While resolvent analysis is naturally suited to globally stable flows, its extension to globally unstable systems presents challenges. In such cases, the relevance of the resolvent operator becomes less clear, since it is nominally associated with the steady-state response of the system [11]. One strategy to mitigate this involves exponential discounting to shift unstable eigenvalues into the stable region of the spectrum [57]. Alternatively, data-driven resolvent formulations have been proposed to bypass the reliance on a globally stable linear operator [39, 30]. These methods maintain the benefits of resolvent-based estimation, specifically by remaining robust against global flow instability.

Sensor placement is crucial for accurate flow estimation, influencing the fidelity of sensor-based measurements and subsequent control strategies. While formal optimization of sensor placement can significantly enhance estimation accuracy [36, 45, 23], such approaches often face practical limitations due to physical and operational constraints. Consequently, this study does not explicitly aim to optimize realistic sensor placement. Instead, effective sensor locations are determined empirically by assessing coherence between individual sensor–target pairs and by investigating single-sensor estimation errors, thereby providing practical insights relevant to realistic experimental scenarios. Within resolvent-based frameworks, spatial coherence has emerged as a particularly valuable metric for evaluating the suitability of sensor–target pairs. Recent experimental studies [35, 3, 4] and numerical analyses [54, 30] demonstrate that coherence-based approaches effectively identify regions that yield accurate estimation and control. Furthermore, analyzing single-sensor estimation errors offers direct guidance for selecting sensor locations, particularly in high-coherence regions or along predictable disturbance propagation paths [30]. Alternatively, streamline visualizations can effectively identify sensor placements dynamically connected to target regions in convectively dominated flows [26].

The objective of the present study is to estimate unsteady turbulent fluctuations in the wake of a NACA 0012 airfoil at Re=23,000Re = 23{,}000 using limited measurements on the surface of the airfoil. Building on our prior work on a laminar wake [30], we employ a causal resolvent-based estimation approach and focus on estimating velocity fluctuations in the turbulent wake, for which the flow exhibits broadband, multi-scale dynamics rather than periodic shedding. Unlike the laminar case, no upstream forcing is required to induce chaotic fluctuations; instead, we estimate naturally occurring turbulent fluctuations. The linearized Navier–Stokes operator in this regime is globally unstable, making traditional resolvent formulations poorly suited. To address this, we adopt a data-driven approach that constructs transfer functions from nonlinear simulation data, using empirical cross-spectral densities to approximate the resolvent operator [39, 30]. These estimators leverage the statistical structure of colored-in-time nonlinear forcing [52] and can be constructed without a priori model reduction, maintaining computational efficiency. Furthermore, we enforce causality through a Wiener–Hopf-based formalism [43], enabling real-time estimation for control applications [27, 39]. This work demonstrates that resolvent-based methods can provide accurate, interpretable, and scalable estimators for spanwise-periodic turbulent wakes by exploiting coherent flow structures [51].

The remainder of this paper is organized as follows. In § 2, we describe the flow configuration, numerical simulations, validation procedures, and the dataset used to construct data-driven estimation kernels, including definitions of three cases: spanwise-averaged, spanwise-Fourier, and mid-span plane. In § 3, we briefly outline the resolvent-based estimation framework, including the theoretical formulation, the derivation of the causal resolvent-based estimation kernels via the Wiener-Hopf method, and implementation of the resolvent-based estimation tools. Estimation results for the three cases are discussed in detail in § 4. Finally, concluding remarks and future research directions are presented in § 5.

Problem set-up

Problem description

We consider the turbulent wake of a NACA0012 airfoil at a moderate chord-based Reynolds number of Re⁡Lc=23,000\operatorname{Re}_{L_c} = 23{,}000 and an angle of attack of α=6∘\alpha= 6^\circ, as studied in several previous works [33, 41, 56, 53]. The free-stream Mach number is set to M∞≡u∞/c∞=0.3M_\infty\equiv u_\infty/c_\infty= 0.3, where u∞u_\infty and c∞c_\infty denote the free-stream velocity and sound speed, respectively. Shear-stress sensors are placed on the airfoil surface, while the targets are located downstream in the turbulent wake (see § 4 for details). In this paper, we present a resolvent-based estimation of the time-series fluctuations in the streamwise velocity ux′u'_x around the mean flow u‾x\overline{u}_x.

Simulation

A large-eddy simulation (LES) utilizing the high-fidelity compressible flow solver CharLES from Cadence Design Systems [56] (Brès et al. 2017; Brès et al. 2018; Brès et al. 2022) is conducted to simulate turbulent airfoil flow. The simulation is conducted on Koehr, the Department of Defense’s supercomputer, an HPE SGI 8600 system with a peak performance of 3.05 PFLOPS. For this study, 50 nodes of the supercomputer, each equipped with 48 cores, were utilized. A C-shaped mesh, generated using Pointwise, is depicted in Figure 1(a). Figure 1(b) and (Figure 1c) illustrate the mean, instantaneous streamwise velocity field, respectively. The airfoil’s leading edge is positioned at the origin, x/Lc=y/Lc=0x/L_c = y/L_c = 0. The computational domain spans x/Lc∈[−20,21]x/L_c \in[-20, 21], y/Lc∈[−20,20]y/L_c \in[-20, 20], and z/Lc∈[−0.1,0.1]z/L_c \in[-0.1, 0.1]. To optimize the mesh resolution, adaptive refinement was employed in the transverse and spanwise directions. A characteristic boundary condition [ρ,ux,uy,uz,P]=[ρ∞,U∞,0,0,P∞][\rho, u_x, u_y, u_z, P] = [\rho_\infty, U_\infty, 0, 0, P_\infty] was applied at the domain edges, with a sponge layer implemented for x/Lc∈[11,21]x/L_c \in[11, 21] to mitigate spurious reflections at the outflow. The time integration used a constant Courant-Friedrichs-Lewy (CFL) number of 0.84.

Figure 1. Computational mesh and simulation: (a) the complete C-shaped grid, with a zoomed-in view of the mesh near the wall shown in the inset; (b) the mean streamwise velocity uxu_x; and (c) a snapshot of the instantaneous streamwise velocity uxu_x obtained from the large-eddy simulation.

We validate the LES by comparing the pressure coefficient and aerodynamic forces

Cp=p−p∞12ρ∞U∞2A,CD=FD12ρ∞U∞2A,andCL=FL12ρ∞U∞2A(1)C_p = \frac{p-p_\infty}{\frac{1}{2}\rho_\infty U_\infty^2 A}, \qquad C_D = \frac{F_D}{\frac{1}{2}\rho_\infty U_\infty^2 A}, \qquad\text{and}\qquad C_L = \frac{F_L}{\frac{1}{2}\rho_\infty U_\infty^2 A} \tag*{(1)}

with previous works in Table 1 and Figure 2. Experimental data is provided by Kim et al. [ [32]. The closest analogue to our simulation is that of Yeh and Taira [ [56], which entails the same physical setup and solver but a different grid. The simulations of Kojima et al. [ [33] and Munday and Taira [ [41] differ due to their use of an incompressible flow solver.

CˉD\bar{C}_DCˉL\bar{C}_L
Present study0.06630.5836
Yeh and Taira [ [56]0.0660.609
Munday and Taira [ [41]0.0620.637
Kojima et al. [ [33]0.0540.639

Table 1. Comparison of the time-averaged drag and lift coefficients with the reference data for a NACA 0012 airfoil at ReLc=23,000Re_{L_c}=23{,}000 and angle of attack 6∘6^\circ.

Figure 2. Comparison of the pressure coefficient CpC_p with previous works.

As shown in Figure 3, the shear layer roll-up on the suction surface occurs at x/Lc≈0.4x/L_c \approx0.4, leading to spanwise vortices. A laminar separation bubble is observed on the suction side of the airfoil in the region 0.1≲x/Lc≲0.840.1 \lesssim x/L_c \lesssim0.84, as indicated by the mean streamwise velocity shown in Figure 1(b). Laminar-turbulent transition is detected at x/Lc≈0.6x/L_c \approx0.6, as determined by the termination of the pressure coefficient plateau illustrated in Figure 2. Finally, a turbulent wake develops behind the airfoil.

Figure 3. Q-criterion visualization showing the key flow features.

Dataset

We consider three distinct representations of the spanwise-periodic flow: spanwise-averaged, spanwise-Fourier, and mid-span plane cases. The spanwise-averaged case is the simplest representation, defined mathematically as

qspan-avg(x,y,t)=1Lz∫0Lzq(x,y,z,t) dz(2)\boldsymbol{q}_{\mathrm{span\text{-}avg}}(x,y,t)=\frac{1}{L_z}\int_{0}^{L_z}\boldsymbol{q}(x,y,z,t)\,\mathrm{d}z \tag*{(2)}

where LzL_z is the spanwise length. Spanwise-Fourier decomposition, a common technique in biglobal stability analyses of three-dimensional flows [50], has been previously utilized to investigate resolvent gains at various spanwise wavenumbers [56, 53]. We similarly analyze spanwise-Fourier modes defined by

q^(x,y,kz,t)=1Lz∫0Lzq(x,y,z,t)e−ikzz dz,(3)\hat{q}(x,y,k_z,t) = \frac{1}{L_z}\int_{0}^{L_z} q(x,y,z,t)e^{-ik_z z}\,\mathrm{d}z, \tag*{(3)}

where kzk_z denotes the spanwise wavenumber. This approach allows us to progressively incorporate more complex flow structures by examining the spanwise Fourier modes. Finally, the mid-span plane case focuses on the flow at the central spanwise location, defined as

qmid(x,y,t)=q(x,y,zmid,t),(4)q_{\mathrm{mid}}(x,y,t) = q(x,y,z_{\mathrm{mid}},t), \tag*{(4)}

where zmid=Lz/2z_{\mathrm{mid}} = L_z/2 is the mid-span location. This representation helps capture spanwise effects in the estimation process by examining the flow at a representative spanwise position and is consistent with a realistic use case where sensors are distributed along the airfoil at a single spanwise position. These representations enhance our understanding of spanwise effects in the flow and support investigations into sensor placement and flow estimation strategies for a spanwise-periodic flow. The dataset comprises nt=75,000n_t = 75{,}000 time-resolved, three-dimensional snapshots of [ρ,ρux,ρuy,ρuz,T][\rho,\rho u_x,\rho u_y,\rho u_z,T], spanning a nondimensional time window of tU∞/Lc∈[0,324]tU_\infty/L_c \in[0,324]. These snapshots are sampled at a uniform interval of ΔtU∞/Lc=0.00432\Delta tU_\infty/L_c = 0.00432, which resolves the dominant vortex-shedding frequency at Stα≡fLc(sin⁡α)/U∞≈0.15St_\alpha\equiv fL_c(\sin\alpha)/U_\infty\approx0.15. This finer temporal resolution and longer duration compared to previous datasets [53] enable capturing smaller-scale turbulent fluctuations in time and provide a larger number of snapshots, resulting in improved convergence of the estimation kernels. The time window captures approximately 466 shedding cycles, providing a sufficiently long time series to ensure statistical convergence of spectral quantities, including the cross-spectral densities used in constructing the estimation kernel. The spatial domain covers x/Lc∈[−0.5,2.5]x/L_c \in[-0.5,2.5] and y/Lc∈[−0.5,0.5]y/L_c \in[-0.5,0.5], capturing the near-wake region with high spatial fidelity.

To construct resolvent-based estimation kernels, we follow the implementation of Jung et al. [ [30]. Prior to estimation, the dataset was preprocessed by subtracting the temporal mean from each variable and applying a Hamming window [21] to reduce spectral leakage in the Fourier transform. For assessing generalization performance, 80% of the data is used to train the estimation model, while the remaining 20% is reserved for testing.

Resolvent-based estimation framework

In this section, we briefly review the resolvent-based estimation framework developed in recent studies [52, 38, 39, 30].

Estimation system

We start with the compressible Navier-Stokes equations written as

∂q∂t=F(q),(5)\frac{\partial\mathbf{q}}{\partial t} = \mathcal{F}(\mathbf{q}), \tag*{(5)}

where q\mathbf{q} is a state vector of flow variables [ρ,ρux,ρuy,ρuz,ρE]T[\rho,\rho u_x,\rho u_y,\rho u_z,\rho E]^T and F\mathcal{F} is the nonlinear Navier-Stokes operator. The equations are linearized using a Reynolds decomposition, giving

∂q′∂t−Aq′=f(qˉ,q′),(6)\frac{\partial\mathbf{q}'}{\partial t} - A\mathbf{q}' = f(\bar{\mathbf{q}},\mathbf{q}'), \tag*{(6)}

where qˉ\bar{\mathbf{q}} and q′\mathbf{q}' represent the mean and perturbation state vectors of the flow variables, respectively, A=∂F∂q∣qˉA = \left.\frac{\partial\mathcal{F}}{\partial\mathbf{q}}\right|_{\bar{\mathbf{q}}} is the linearized Navier-Stokes operator, and ff represents the remaining nonlinear terms. For convenience, we drop the (⋅)′(\cdot)' superscript for perturbations from this point on. To derive the estimation method, we consider a generalization of (5) in the form of the linear-time-invariant (LTI) system

dqdt(t)=Aq(t)+Bff(t),y(t)=Cyq(t)+n(t),z(t)=Czq(t),(7)\begin{aligned} \frac{d\mathbf{q}}{dt}(t) &= A\mathbf{q}(t) + B_f\mathbf{f}(t),\\ \mathbf{y}(t) &= C_y\mathbf{q}(t) + \mathbf{n}(t),\\ \mathbf{z}(t) &= C_z\mathbf{q}(t), \tag*{(7)} \end{aligned}

where the forcing matrix Bf∈Cn×nfB_f \in\mathbb{C}^{n \times n_f} can be used to restrict the form of the forcing ff, and the measurement y\mathbf{y} and target z\mathbf{z} indicate readings of the state perturbation extracted by a measurement matrix Cy∈Cny×nC_y \in\mathbb{C}^{n_y \times n} and a target matrix Cz∈Cnz×n\mathbf{C}_z \in\mathbb{C}^{n_z \times n}. The number of sensors and targets is denoted nyn_y and nzn_z, respectively. The vector n\mathbf{n} indicates the sensor noise. The measurement y\mathbf{y} is chosen to be the shear stress τw\tau_w at one or more points on the surface of the airfoil. It is computed from the state q\mathbf{q} using a suitably defined measurement matrix Cy\mathbf{C}_y, as in Jung et al. [ [30]. In line with recent applications of the resolvent-based framework [2, 54], preliminary tests indicated minimal difference between using shear stress and pressure as the measured quantity on the airfoil surface. The target z\mathbf{z} represents one or more Gaussian sensors, each with spatial support given by

αe−(x−xc)2/2σx2−(y−yc)2/2σy2−(z−zc)2/2σz2,(8)\alpha e^{-(x-x_c)^2/2\sigma_x^2-(y-y_c)^2/2\sigma_y^2-(z-z_c)^2/2\sigma_z^2}, \tag*{(8)}

where σx\sigma_x, σy\sigma_y, and σz\sigma_z define the width of the Gaussian distribution in each coordinate direction, and α\alpha is a weighting factor representing the integrated contribution over the Gaussian support. These targets are extracted from the state using the measurement matrix Cz\mathbf{C}_z.

By Fourier-transforming the linear system into the frequency domain and defining the resolvent operator as R=(iωI−A)−1\mathbf{R}=(i\omega\mathbf{I}-\mathbf{A})^{-1}, where I\mathbf{I} is the identity matrix and ω\omega is the frequency, we derive modified resolvent operators used for constructing the resolvent-based kernels for estimation. The measurement and target vectors can be written as

y^=Ryff^+n^,(9)\hat{\mathbf{y}}=\mathbf{R}_{y f}\hat{\mathbf{f}}+\hat{\mathbf{n}}, \tag*{(9)}
z^=Rzff^(10)\hat{\mathbf{z}}=\mathbf{R}_{z f}\hat{\mathbf{f}} \tag*{(10)}

with Ryf=CyRBf\mathbf{R}_{y f}=\mathbf{C}_y\mathbf{R}\mathbf{B}_f, and Rzf=CzRBf\mathbf{R}_{z f}=\mathbf{C}_z\mathbf{R}\mathbf{B}_f. The notation (⋅^)(\hat{\cdot}) indicates a quantity in the frequency domain.

Kernels for resolvent-based estimation

We perform estimation with three different kernels: non-causal, truncated non-causal, and causal [39]. First, we start with a non-causal estimator using a convolution function, written as

z~nc(t)=∫−∞∞Tnc(t−τ)yn(τ) dτ,(11)\tilde{\mathbf{z}}_{nc}(t)=\int_{-\infty}^{\infty}\mathbf{T}_{nc}(t-\tau)\mathbf{y}_n(\tau)\,d\tau, \tag*{(11)}

where Tnc∈Rnz×ny\mathbf{T}_{nc}\in\mathbb{R}^{n_z\times n_y} is a non-causal estimation kernel between the sensor measurement and the estimated target state. The objective is to select the kernel to minimize the expected value of the estimation error e(t)=z~−z(t)e(t)=\tilde{\mathbf{z}}-\mathbf{z}(t), and this is formalized by defining the cost function

Jnc(t)=∫−∞∞E{e(t)†e(t)} dt,(12)J_{nc}(t)=\int_{-\infty}^{\infty}\mathbb{E}\{e(t)^{\dagger}e(t)\}\,dt, \tag*{(12)}

where E{⋅}\mathbb{E}\{\cdot\} is the expectation operator. The overall goal can be explained more easily using the block diagram in Figure 4(a).

Figure 4. Block diagram of resolvent-based estimation: (a) design of the resolvent-based estimator based on the linear system and (b) application to the nonlinear system. Here, (⋅)′(\cdot)^\prime indicates fluctuations around the mean quantity, (⋅ˉ)(\bar{\cdot}) denotes mean quantity, and (⋅~)(\tilde{\cdot}) represents an estimated quantity.

By minimizing the cost function, we obtain a non-causal estimation kernel

T^nc(ω)=(RzfF^Ryf†)(RyfF^Ryf†+N^)−1,(13)\hat{\mathbf{T}}_{nc}(\omega)=\left(\mathbf{R}_{z f}\hat{\mathbf{F}}\mathbf{R}_{y f}^{\dagger}\right)\left(\mathbf{R}_{y f}\hat{\mathbf{F}}\mathbf{R}_{y f}^{\dagger}+\hat{\mathbf{N}}\right)^{-1}, \tag*{(13)}

where F^=E{f^f^†}\hat{\mathbf{F}}=\mathbb{E}\{\hat{\mathbf{f}}\hat{\mathbf{f}}^{\dagger}\} and N^=E{n^n^†}\hat{\mathbf{N}}=\mathbb{E}\{\hat{\mathbf{n}}\hat{\mathbf{n}}^{\dagger}\} denote the forcing and sensor noise cross-spectral density matrices, respectively. Note that the space-time color of the forcing terms is explicitly included in (13), which means that the nonlinearity of the flow can be statistically accounted for in the transfer function.

Second, for real-time estimation, the only current and past (but not future) sensor measurements are available to the estimator. One common approach to addressing this practical limitation is to truncate the non-causal kernel by setting the part associated with unavailable future measurements to zero. The truncated non-causal kernel is defined as

Ttnc(τ)={Tnc(τ),τ≥0,0,τ<0.(14)\mathbf{T}_{tnc}(\tau) = \begin{cases} \mathbf{T}_{nc}(\tau), & \tau\ge0,\\ 0, & \tau< 0. \end{cases} \tag*{(14)}

The truncated non-causal estimates are computed as

z~tnc(t)=∫−∞0Ttnc(t−τ)yn(τ) dτ.(15)\tilde{\mathbf{z}}_{tnc}(t) = \int_{-\infty}^{0} \mathbf{T}_{tnc}(t-\tau)\mathbf{y}_n(\tau)\,\mathrm{d}\tau. \tag*{(15)}

Lastly, by enforcing causality via Wiener-Hopf formalism in cost functions, we derive optimal causal estimation kernels under the constraint of causality. A causal estimator

z~c(t)=∫−∞0Tc(t−τ)yn(τ) dτ,(16)\tilde{\mathbf{z}}_c(t) = \int_{-\infty}^{0} \mathbf{T}_c(t-\tau)\mathbf{y}_n(\tau)\,\mathrm{d}\tau, \tag*{(16)}

is defined in terms of the causal estimation kernel Tc∈Rnz×ny\mathbf{T}_c \in\mathbb{R}^{n_z \times n_y}. To enforce causality, we modify the cost function of (12) to read

Jc(t)=∫−∞∞E{e(t)∗e(t)}+(Λ−(t)Tc(t)+Λ+†(t)Tc†(t)) dt,(17)J_c(t) = \int_{-\infty}^{\infty} \mathbb{E}\{e(t)^*e(t)\} + \left(\boldsymbol{\Lambda}_{-}(t)\mathbf{T}_c(t) + \boldsymbol{\Lambda}_{+}^{\dagger}(t)\mathbf{T}_c^{\dagger}(t)\right)\,\mathrm{d}t, \tag*{(17)}

where Λ\boldsymbol{\Lambda} is a Lagrange multiplier that is used to force the causal kernel to be zero for the non-causal part (τ<0)(\tau< 0). The (⋅)+(\cdot)_{+} and (⋅)−(\cdot)_{-} subscripts represent the non-causal (τ<0)(\tau< 0) and causal (τ>0)(\tau> 0) parts of any matrix or function to be zero by achieving a Wiener-Hopf factorization. Additionally, [⋅]+[\cdot]_+ and (⋅)+(\cdot)_+ denote additive and multiplicative factorization operators, respectively (see Appendix § 9 for further details). The derived causal kernel for the estimation is

T^c(ω)=[RzfF^Ryf†(RyfFRyf†+N^)−1]+(RyfFRyf†+N^)+−1.(18)\hat{T}_c(\omega) = \left[R_{z_f}\hat{F}R_{y_f}^{\dagger}\left(R_{y_f}F R_{y_f}^{\dagger}+\hat{N}\right)^{-1}\right]_+\left(R_{y_f}F R_{y_f}^{\dagger}+\hat{N}\right)_+^{-1}. \tag*{(18)}

All the transfer functions we consider involve the forcing cross-spectra density matrix that can account for the impact of the nonlinearity in a statistical sense. However, our method is more suitable for the real-time estimation approach since causality is constrained. In this paper, we present the results for both the causal and truncated non-causal transfer functions to assess how optimally enforcing causality impacts the estimation accuracy for turbulent flow.

The resolvent operators appearing in the estimation kernels are not well-defined for globally unstable systems [24, 57] such as the linearization of the turbulent airfoil wake about its mean [56]. To circumvent this issue, we use a data-driven approach [39] that enables the construction of resolvent-based kernels without the need to explicitly form resolvent operators. The empirical cross-spectra densities (CSD) from the simulation are used to obtain the modified resolvent operators, which is a similar way to the previous work [3, 30]. Following the notation of the LTI system in § 3.1, the datasets of the sensor and target readings are Fourier-transformed, expressed as

\begin{bmatrix} \hat{\boldsymbol{y}} \\ \hat{\boldsymbol{z}} \end{bmatrix} = \begin{bmatrix} R_{y,f} & 1 \\ R_{z,f} & 0 \end{bmatrix} \begin{bmatrix} \hat{\boldsymbol{f}} \\ \hat{\boldsymbol{n}} \end{bmatrix}. \tag*{(19)}\end{bmatrix}

Computing the cross-spectral density of [y^ z^]T[\hat{\boldsymbol{y}}\ \hat{\boldsymbol{z}}]^{T} gives

\begin{bmatrix} S_{y_f,y_f} & S_{y_f,z_f} \\ S_{z_f,y_f} & S_{z_f,z_f} \end{bmatrix} = \begin{bmatrix} R_{y,f}\hat{F}R_{y,f}^{\dagger} & R_{y,f}\hat{F}R_{z,f}^{\dagger} \\ R_{z,f}\hat{F}R_{y,f}^{\dagger} & R_{z,f}\hat{F}R_{z,f}^{\dagger} \end{bmatrix}. \tag*{(20)}\end{bmatrix}

with Syf,yf=E{y^y^∗}S_{y_f,y_f}=\mathbb{E}\{\hat{\boldsymbol{y}}\hat{\boldsymbol{y}}^*\} and Szf,yf=E{z^y^∗}S_{z_f,y_f}=\mathbb{E}\{\hat{\boldsymbol{z}}\hat{\boldsymbol{y}}^*\}. Since the right-hand side of (20) contains the terms needed to build the estimation kernels, this shows that the correlations on the left-hand side can be used in their place in (3.8 and (18). The data-driven non-causal and causal estimation kernels in (13) and (18) are computed using the CSDs from (20), yielding

T^nc=Szy(Syy+N^)−1,(21)\hat{T}_{nc}=S_{zy}(S_{yy}+\hat{N})^{-1}, \tag*{(21)}
T^c=[Szy(Syy+N^)−1]+(Syy+N^)+−1.(22)\hat{T}_{c}=\left[S_{zy}(S_{yy}+\hat{N})^{-1}\right]_+(S_{yy}+\hat{N})_+^{-1}. \tag*{(22)}

Note that the CSDs inherently contain statistical information related to the nonlinearities of the flow within the forcing covariance matrix. The mean flow is subtracted from both the measurement readings and target values. Estimation kernels are computed offline for the linear system, as illustrated in Figure 4(a). These kernels are then used for real-time (online) estimation of velocity fluctuations in the wake, applying the approach to the nonlinear system, as depicted in Figure 4(b).

Implementation of resolvent-based estimation

We employ recently developed resolvent-based estimation and control tools integrated within the compressible flow solver CharLES [54] (Jung et al. 2024), which was carefully designed to scale to large-scale problems such as a turbulent wake. Originally inspired by the incompressible solver implementation by [39], the approach was extended by [30] to compressible flows using parallel algorithms written in C++, built directly upon the existing solver architecture. These resolvent-based tools interact with the solver, enabling efficient in-situ computations during simulations. Moreover, our modular software design simplifies integration with other relevant software packages and ensures straightforward deployment in high-performance computing environments.

An overview of the implementation is shown in Figure 5. Our compressible resolvent-based tool integrates external libraries such as PETSc [5] and FFTW [17], enabling scalable parallel computation through in-situ matrix operations with flow quantities during the training process. The tool constructs measurement matrices (CyC_y and CzC_z) using control volume indices from the CFD mesh. For cases involving high-rank targets (nz≫nyn_z \gg n_y), an online discrete Fourier transform (DFT) is used to minimize memory consumption while preserving time-resolved information [48, 14, 15]. Training data is obtained from large eddy simulations (LES), and the corresponding cross-spectral densities (CSDs) are used to generate the estimation kernels. The DFT parameters used to obtain converged kernels are described in Appendix B.

Figure 5. Flowchart of the resolvent-based estimation tool within a compressible flow solver. Dashed-line boxes represent the resolvent-based tool integrated into the existing CFD solver (solid-line box). Blue boxes, including those outlined in red (offline run) and orange (build kernels) dashed lines, indicate offline processes, while black boxes with green solid outlines represent online (estimation) processes.

Results

We demonstrate the effectiveness of the causal resolvent-based approach for predicting turbulent fluctuations over a NACA0012 airfoil at a 6∘6^\circ angle of attack. Unlike earlier resolvent-based studies that employed non-causal estimation methods [52, 38, 2, 1], the causal estimator uses only present and past measurements and kernels optimized for this purpose via the Wiener-Hopf method [39]. This causality enforcement makes our method particularly suitable for real-time applications. Significantly, this work is the first numerical investigation

explicitly applying the Wiener-Hopf method to enforce causality in turbulent flow estimation Jung and Towne, 2024, extending previous efforts primarily focused on experimental flow-control studies [3, 4] and laminar-flow scenarios [39, 30].

As previously mentioned, our analysis centers on the spanwise-averaged, spanwise-Fourier, and mid-span plane cases, as depicted in Figure 6. The specific target locations analyzed in the wake region are also highlighted in Figure 6(a). The spanwise-averaged case provides a concise yet informative view of spatial structure in the spanwise direction, enabling a focused analysis of sensor positioning in the streamwise and cross-stream planes. We progressively incorporate more complex flow structures by examining the spanwise-Fourier modes, with particular attention to the most energetic mode at kz=10πk_z = 10\pi, and the flow on the mid-span plane to better capture spanwise effects in the estimation process.

Streamwise velocity fluctuation fields for spanwise-averaged, spanwise-Fourier mode, and mid-span plane cases

Figure 6. Streamwise velocity fluctuation fields (ux′/U∞u'_x/U_\infty) for (a) spanwise-average, (b) spanwise-Fourier mode kz=10πk_z = 10\pi, and (c) mid-span plane case. Target locations (z1z_1, z2z_2, z3z_3, z4z_4) are indicated by blue circles and positioned along the trailing edge at streamwise coordinates x/Lc=[1.2,1.5,2.0,2.5]x/L_c = [1.2, 1.5, 2.0, 2.5] for a constant transverse position y/Lc=−0.11y/L_c = -0.11.

Given the large number of potential sensor positions available on the three-dimensional airfoil surface, our investigation begins with selecting the most effective sensor locations based on single-sensor estimation error metrics and coherence analyses. Subsequently, we examine the power spectral density (PSD) at these selected sensor and target locations to better understand their frequency-domain characteristics. We then construct estimation kernels specifically designed for multi-sensor estimation, analyzing their characteristics in both the time and frequency domains to gain insight into their role in estimation performance. Finally, we present multi-sensor estimation results, quantifying errors at both single target points and over extended

target regions, to demonstrate the accuracy of the resolvent-based method.

Investigation of sensor placement

Sensor placement is guided by evaluating single-sensor estimation error metrics, similar to the approach in Jung et al. [ [30], as well as assessing coherence between sensor and target locations [35, 4]. The estimation error used throughout this paper is quantified by the metric [39, 30] (Jung and Towne 2024)

E=∑i∫(z~i(t)−zi(t))2dt∑i∫(zi(t))2dt,(23)E = \frac{\sum_i \int(\tilde{z}_i(t)-z_i(t))^2 \mathrm{d}t}{\sum_i \int(z_i(t))^2 \mathrm{d}t}, \tag*{(23)}

where z~i\tilde{z}_i and ziz_i represent the estimated and true values at the ii-th target location, respectively. Additionally, coherence provides valuable insights into frequency-dependent estimation performance and is defined as [52]:

γ^yz(ω)=∣S^yz(ω)∣S^yy(ω)S^zz(ω)(24)\hat{\gamma}_{yz}(\omega) = \frac{\left|\hat{S}_{yz}(\omega)\right|}{\sqrt{\hat{S}_{yy}(\omega)}\sqrt{\hat{S}_{zz}(\omega)}} \tag*{(24)}

where S^yz\hat{S}_{yz} denotes the cross-spectral density between sensor and target, and S^yy\hat{S}_{yy} and S^zz\hat{S}_{zz} denote their respective power spectral densities.

Figure 7 presents spatial maps of estimation errors for a single sensor estimating streamwise velocity fluctuations at a single target location. Results are compared between the truncated non-causal (panels aa, cc, ee) and causal (panels bb, dd, ff) estimation approaches, covering three different flow representations: spanwise-averaged case (panels aa, bb), spanwise-Fourier modes at wavenumbers kz=10πk_z = 10\pi (panel cc, dd), and mid-span plane case (panels ee, ff). For the spanwise-Fourier case, we focus specifically on the wavenumber kz=10πk_z = 10\pi, as it represents the lowest frequency and highest energy modes identified by previous resolvent gain studies [56, 53].

Figure 7. Estimation error maps for the streamwise velocity fluctuation ux′u'_x in single sensor-target configurations: (a, b) spanwise-averaged flow, (c, d) spanwise-Fourier mode for kz=10πk_z = 10\pi, and (e, f) mid-span plane flow. Results using the truncated non-causal approach are shown in panels (a, c, e), while the causal estimation results are shown in panels (b, d, f).

Sensor locations are characterized using the coordinate ss, defined such that positive values correspond to the suction surface and negative values to the pressure surface of the airfoil, with the magnitude representing the normalized streamwise position (x/Lcx/L_c). Overall, the causal estimation method consistently outperforms the truncated non-causal approach. This advantage is particularly noticeable near the trailing-edge region (1<x/Lc<1.51 < x/L_c < 1.5) and prominently so when sensors are positioned on the front surfaces of the airfoil (−0.5<s<0.5-0.5 < s < 0.5). The performance improvement is more pronounced for the spanwise-averaged flow compared to the mid-span flow. This difference arises primarily due to the characteristics of the laminar region spanning −0.5<s<0.5-0.5 < s < 0.5 on the surface of the airfoil, where larger spanwise structures exist, resulting in less information about turbulent fluctuations in the wake, diminishing estimation accuracy. The detrimental impact of laminar regions on estimation accuracy is especially evident in the spanwise Fourier modes. For the spanwise Fourier modes, sensors located within the laminar region (−0.5<s<0.5-0.5 < s < 0.5), particularly on the pressure surface (−0.5<s<0-0.5 < s < 0), exhibit poor estimation performance. This effect is notably stronger at low wavenumbers, e.g., kz=10πk_z = 10\pi, likely due to its larger associated spanwise structures compared to higher wavenumbers, e.g., kz=20πk_z = 20\pi. However, downstream of the laminar-to-turbulent transition, estimation performance significantly improves due to the emergence of large-scale turbulent structures within the wake that are better correlated with the measurements.

Figure 8 presents the average estimation errors over the wake region as a function of sensor location ss, comparing spanwise-averaged (S-A), spanwise-Fourier (S-F), and mid-span plane (M-S) flows. These results are shown separately for the streamwise velocity fluctuations (ux′u'_x, panel aa) and the cross-streamwise velocity fluctuations (uy′u'_y, panel bb). Here, we report the average error over a set of targets in the wake that are uniformly distributed along the line segment 1<x/Lc<2.51 < x/L_c < 2.5 and y/Lc=−0.11y/L_c = -0.11. The resolvent-based kernels, which inherently include the linearized Navier–Stokes operator, effectively estimate both velocity components from shear-stress sensor measurements. This effectiveness implies potential applicability of our method for estimating other relevant flow quantities, such as the vorticity field. Sensors placed on the pressure surface generally yield higher accuracy in spanwise-averaged and mid-span flows. Interestingly, the laminar region on the suction surface also performs well for estimation in spanwise-averaged flows, which contrasts with the results shown previously in Figure 7. This discrepancy arises because the targets analyzed in Figure 8 span both the upper and lower wake regions relative to the trailing edge, thereby incorporating regions of different coherence characteristics. Additionally, we observe a slight deterioration in estimation accuracy for sensors within the laminar separation bubble region (0.4<s<0.70.4 < s < 0.7), although accuracy improves progressively as the sensor location approaches the trailing edge. Overall, superior estimation performance is achieved for the spanwise-averaged flow compared to the mid-span flow, with the spanwise Fourier modes exhibiting intermediate performance. Based on these observations, sensor positions near the trailing edge (0.5<x<10.5 < x < 1) and on the upstream suction (0<x<0.30 < x < 0.3) and pressure (−1<x<−0.7-1 < x < -0.7) surfaces are identified as particularly effective locations for achieving high-performance resolvent-based estimation.

Figure 8. Estimation errors of streamwise (aa) and cross-streamwise (bb) velocities as a function of the sensor location on the airfoil surface. The blue, orange, purple, and green lines represent spanwise-averaged (S-A), mid-span (M-S), and spanwise-Fourier (S-F) (Kz=10πK_z = 10\pi) flows, respectively. The solid diamond (⋄\diamond) and dashed square (□\square) lines denote the causal and truncated non-causal approaches, respectively.

In Figure 9, we examine coherence of the streamwise velocity fluctuations between the sensor and the wake regions for the spanwise-averaged and mid-span flows at the sensor locations where single-sensor estimation was effective, as demonstrated in Figure 7 and Figure 8. These locations include regions on the front suction side (0<x/Lc<0.30 < x/L_c < 0.3), the rear pressure side (−1<x/Lc<−0.7-1 < x/L_c < -0.7), and the mid-chord area (0.5<x/Lc<10.5 < x/L_c < 1), as illustrated in Figure 9. Since our goal in this coherence study is to gain physical insights into coherence between sensor locations and wake fluctuations, we focus our analysis on the near-wake target position at x/Lc=1.2x/L_c = 1.2. We confirmed that coherence trends at farther wake positions were similar but with reduced magnitudes. Specifically, the sensors representing the laminar regions were placed at 1 (suction side, laminar region 0<x/Lc<0.40 < x/L_c < 0.4) and 6 (pressure side, laminar region −1<x/Lc<0-1 < x/L_c < 0), as shown in Figure 9. Within each laminar region, the coherence patterns remain similar, differing only in magnitude. Notably, spanwise-averaged flow fields exhibit stronger coherence at frequencies of interest (Stα<0.2St_\alpha< 0.2) compared to mid-span flows. This enhanced coherence results from spatially larger coherent fluctuations associated񎟽 with spanwise averaging, resulting in stronger coupling between sensor and target fluctuations. Interestingly, laminar regions (sensors 1 and 6) exhibit significant coherence with the near-wake target, suggesting that upstream laminar disturbances may be inherently linked to downstream wake fluctuations [30]. Furthermore, sensor 5, located in the turbulent region, demonstrates notable coherence with the target across a wide frequency range. Among middle locations (sensors 2, 3, and 4), each sensor displays pronounced coherence at the frequency bands of interest (Stα<0.2St_\alpha< 0.2). These locations are empirically selected to capture dominant frequencies at the target, which are crucial for kernel-based amplification in the frequency domain.

Coherence of the streamwise velocity with respect to the target $z_1$ for the spanwise-averaged and mid-span flows

Figure 9. Coherence of the streamwise velocity with respect to the target z1z_1 (x/Lc=1.2x/L_c = 1.2) for the spanwise-averaged and mid-span flows.

We further investigated coherence between the sensor and the wake regions with respect to the streamwise velocity fluctuations for the spanwise-Fourier mode at kz=10πk_z = 10\pi. In particular, we are interested in verifying whether coherence is indeed weak in the region −0.7<x/Lc<0-0.7 < x/L_c < 0, as shown in the single-sensor estimation result in Figure 7. To assess this, we examined coherence at sensor location 7, placed at x/Lc=−0.3x/L_c = -0.3, as indicated by the yellow solid line in Figure 10. Although the von Kármán vortex shedding and other dominant frequencies are evident for Stα<0.2St_\alpha< 0.2, sensor 7 does not exhibit significant coherence in this frequency range. In contrast, sensor locations 4 (purple), 5 (blue), and 6 (red) display prominent coherence peaks, consistent with effective estimation performance. Figure 10 further indicates that sensors 5 and 6 exhibit increased coherence at a spanwise frequency of 10π10\pi. Ultimately, we identify sensors 1, 5, and 6 as the most effective for estimation purposes, with an additional selection of sensor 4 from among sensors 2, 3, and 4.

Coherence of the streamwise velocity with respect to the target $z_1$

Figure 10. Coherence of the streamwise velocity with respect to the target z1z_1 (x/Lc=1.2x/L_c = 1.2) of the spanwise-Fourier case at kz=10πk_z = 10\pi.

Power-spectral density of the sensor and target readings

Figure 11 presents the power spectral density (PSD) of the sensor and target signals for the spanwise-averaged, spanwise-Fourier, and mid-span plane flows. Panels (aa) and (bb) highlight three dominant frequencies evident in the signals at sensor positions y3y_3, y4y_4, and y5y_5, as well as the target position z1z_1. The energy associated with these dominant frequencies decreases downstream, as demonstrated by the PSD at target positions z2z_2, z3z_3, and z4z_4 in panel (bb). It is well established that laminar separation bubble (LSB) detachment over the suction surface promotes the Kelvin–Helmholtz instability, resulting in vortex shedding characterized by lower-frequency oscillations (Stα<0.12St_\alpha< 0.12) [13]. These lower-frequency peaks are clearly captured in panel (aa) for sensor positions y3y_3, y4y_4, y5y_5, and the near-wake target z1z_1. In contrast, the turbulent region on the airfoil surface and near wake exhibit dominant von Kármán vortex shedding frequencies within the higher-frequency band (0.152≤Stα≤0.2110.152 \le St_\alpha\le0.211) [56].

Figure 11(c) and (d) illustrate the PSD of sensor and target measurements for the spanwise-Fourier mode at the wavenumber kz=10πk_z = 10\pi, respectively. The PSD computations utilize the same parameters as those used for the spanwise-averaged case. Compared to the spanwise-averaged (a) and mid-span plane (e) cases, the PSD at the sensor and target locations (c) does not exhibit distinct dominant peaks, consistent with the coherence results shown in Figure 10. As observed in Yeh and Taira [ [56] and Towne et al. [ [53], the response modes for spanwise-Fourier modes at kz=10πk_z = 10\pi appear predominantly slightly away from the airfoil surface. Thus, the spanwise Fourier modes at the sensor locations are relatively weak, leading to weaker PSD values, as illustrated in Figure 11(c). Modes at lower wavenumbers correspond to larger, more energetic spanwise structures, whereas modes at higher wavenumbers represent smaller, less energetic structures. We confirmed that the primary difference between the wavenumbers kz=10πk_z = 10\pi and 20π20\pi is the magnitude of their PSD values, while their PSD patterns remain similar.

Figure 11. PSD of streamwise velocity fluctuations ux′u'_x for sensor readings and target readings, obtained from the spanwise-averaged (a) and (b), spanwise-Fourier (kz=10πk_z = 10\pi) (c) and (d), and mid-span plane (e) and (f) cases presented in Figure 6. In (a), the dashed lines indicate positions y1y_1 and y6y_6, corresponding to the laminar flow region.

Figure 11(e) and (f) display the PSD of sensor and target signals in the mid-span plane. Similar to the spanwise-averaged case, the laminar flow region (y1y_1 and y6y_6) exhibits lower energy fluctuations. Additionally, energy progressively dissipates as the target moves further downstream. Dominant frequencies in the approximate range 0.1<Stα<0.20.1 < St_\alpha< 0.2 are distinctly visible in the near-wake targets (z1z_1 and z2z_2), as clearly illustrated in panel (f).

Estimation kernels

Next, we examine the estimation kernels, building on our previous studies [38, 39, 30], where we initially explored kernels within the resolvent-based framework. In this paper, we derive the kernels using a data-driven approach that accounts for the statistical effects of flow nonlinearity, implicitly incorporating the CSD matrix F^nl\hat{F}_{nl}, which acts as a forcing in linear dynamics. Note that when white noise forcing is applied, the estimation kernels correspond to the transfer functions of the Kalman filter [31], as shown by Martini et al. [ [39]. Incorporating the forcing matrix F^nl\hat{F}_{nl} is suitable for this study, as our application involves strongly nonlinear turbulent flows. Modeling the nonlinear terms for estimation leads to better performance. A key characteristic of estimation kernels is the presence of peak points, which reveal the time it takes for hydrodynamic waves to travel from the sensor location to the target. Since the estimation kernels are based on the compressible linearized Navier–Stokes operator, they also capture acoustic waves, resulting in secondary peaks in addition to the hydrodynamic waves [28, 54]. Another important characteristic is whether there are significant values in the non-causal part of the kernel (τ<0\tau< 0), including the peak point [26]. This information is crucial for estimation, but it may be truncated when the estimator is applied to the convolution function if it resides in the non-causal part of the kernels. This truncation can lead to a significant difference in the performance between the causal and truncated non-causal approaches. From a numerical perspective, the estimation kernels function by amplifying the frequency signals of the sensor measurements through multiplication with the kernels to approximate the target signals, i.e., z~^(ω)=T^z(ω)y^(ω)\hat{\tilde{\boldsymbol{z}}}(\omega) = \hat{\mathbf{T}}_z(\omega)\hat{\mathbf{y}}(\omega). Therefore, analyzing the estimation kernels in the frequency domain alongside the PSD of the sensor and target readings in § 4.2 provides valuable numerical insights into accurate estimation.

We examine four kernels, specifically within the single input and multiple outputs configuration (sensor: y1y_1 and targets: z1z_1, z2z_2, z3z_3, z4z_4), as illustrated in Figure 12. This selection is based on the observation that when the sensor is positioned in the laminar region within the effective locations, the kernel’s peaks are distinct, with less noise in other frequencies, showing a clear correlation between the sensor and the target signals. In Figure 12, prominent peak points are observed in the non-causal kernels (aa, cc, ee, gg) at [τpeak,z1,τpeak,z2,τpeak,z3,τpeak,z4]=[−0.360,0.171,0.676,1.25][\tau_{\mathrm{peak},z_1}, \tau_{\mathrm{peak},z_2}, \tau_{\mathrm{peak},z_3}, \tau_{\mathrm{peak},z_4}] = [-0.360, 0.171, 0.676, 1.25], respectively. These points represent the primary hydrodynamic wave travel times between the sensor and the targets. The case in Figure 12(a) serves as a good example of how a causal approach using Wiener–Hopf decomposition can enhance estimation accuracy. When this kernel is applied to real-time estimation for evaluating the convolution function, the peak at τ=−0.36\tau= -0.36, which contains critical travel information of the fluctuations, is truncated. The truncated non-causal kernel in the frequency domain (magenta dashed line) is notably lower in magnitude compared to the causal kernel (blue line), as shown in 12(b). It is important to note that the kernels amplify the sensor measurements at dominant frequencies (0.1<Stα<0.20.1 < St_\alpha< 0.2).

Figure 12. Estimation kernels between sensor y1y_1 and targets z1z_1 (a, b), z2z_2 (c, d), z3z_3 (e, f), and z4z_4 (g, h) for the spanwise-averaged flow. Kernels are shown in the time domain (left column) and frequency domain (right column). The black line represents the non-causal kernel, the blue line represents the causal kernel obtained via Wiener–Hopf decomposition, and the magenta dashed line (when shown) indicates the truncated non-causal kernel.

Imposing sensor is necessary to ensure that the inversion of the PSD is well-posed [38, 39]. The noise level, which is used to regularize the kernels, is set at 10−210^{-2} of the maximum PSD value of the sensor measurements, consistent with the approach used in previous work [39, 30]. Similar to other optimal estimation and control methods [10, 47], the sensor noise is described by correlations that are assumed to be known.

Figure 13 shows the kernels for the spanwise-Fourier modes at kz=10πk_z = 10\pi. Based on Figure 7, sensor placement in the laminar region is less effective; hence, we focus on kernels corresponding to sensor y5y_5, rather than y1y_1, and target z1z_1, consistent with locations examined previously in Figure 12. Because the spanwise Fourier-transformed state is complex-valued, the computational cost for estimation increases by a factor of four. Additionally, the kernels are no longer symmetric at Stα=0St_\alpha= 0, as shown in Figure 13. The peak points are clearly visible (see Figure 13(a) and (Figure 13c)) at τ>0\tau> 0, indicating the dominance of hydrodynamic waves. Consequently, performance differences between causal and truncated non-causal estimation methods are minimal. The values of the kernels are largest in the range of ∣Stα∣<0.2|St_\alpha| < 0.2, effectively amplifying sensor measurements to produce accurate estimates.

Figure 13. Estimation kernels between sensor y5y_5 and target z1z_1 for the spanwise Fourier mode at kz=10πk_z = 10\pi, shown in the time (a)(a) and frequency (b)(b) domains. Sensor and target positions are indicated in Figure 6. The black line represents the non-causal kernel, and the blue line represents the causal kernel obtained via Wiener–Hopf decomposition.

Finally, we present the kernels for the mid-span plane flow in Figure 14. Sensors positioned in both the laminar (y1y_1) and turbulent regions (suction side: y5y_5; pressure side: y6y_6) are shown. The prominent peak points in the kernels between sensors (y1y_1, y5y_5) and target z1z_1 closely match those observed in the spanwise-averaged and spanwise-Fourier flows, respectively, as depicted in Figure 12 and Figure 13 for the kernels between y1y_1 and z1z_1 and y5y_5 and z1z_1, respectively. The kernel between y6y_6 and z1z_1 also aligns well with the other cases, though it is not explicitly shown here. However, the kernels for the mid-span flow exhibit significant amplitudes over a larger range of τ\tau, indicating greater difficulty in achieving temporal convergence. A notable difference appears in Figure 14(a), where the kernel peak lies in the positive domain (τ>0\tau> 0), unlike the corresponding kernel in the spanwise-averaged flow, which peaks in the negative domain. This discrepancy may be attributed to the fact that the spanwise-averaged case integrates the flow across multiple spanwise positions, capturing coherent large-scale structures that extend significantly in the spanwise direction. These large-scale structures are more capable of influencing upstream conditions (non-causal behavior), appearing as peaks in the non-causal part (τ<0\tau< 0) of the kernel. In contrast, the mid-span plane case represents a single spanwise slice, emphasizing smaller-scale, localized spatial structures. Such structures typically have limited upstream influence since their acoustic disturbances are weaker, more rapidly dissipated, and less coherent over larger spanwise distances. Thus, such conditions enhance convective flow characteristics in the mid-span plane case, thereby improving the accuracy when applying truncated non-causal estimation to the mid-span plane flow. Additionally, we observe that the kernel between y4y_4 and z1z_1 is similar to that between y5y_5 and z1z_1 within the mid-span flow, so it is omitted from this figure. Both causal and truncated non-causal kernels for targets further downstream (z2z_2, z3z_3, z4z_4) closely resemble those in the spanwise-averaged flow (Figure 12), with their peak points consistently located in the positive τ\tau domain.

Figure 14. Estimation kernels between sensors y1y_1 (aa, bb), y5y_5 (cc, dd), and y6y_6 (ee, ff) and target z1z_1 for the mid-span plane case. Kernels are shown in the time domain (left column) and frequency domain (right column). The black line represents the non-causal kernel, and the blue line represents the causal kernel obtained via Wiener–Hopf decomposition.

Multi-sensor estimation

By selecting sensor locations y1y_1, y4y_4, y5y_5, and y6y_6 (notations from Figure 9(a) and (Figure 9b)) based on the investigation of the most effective locations using single-sensor estimation and coherence in § 4.1, we show the estimation errors for spanwise-averaged and mid-span flows along the trailing edge as additional sensors are introduced, as shown in Figure 15. The use of sensor y5y_5 (blue) alone does not yield significant improvement over truncated non-causal estimation. However, adding an additional sensor (y6y_6) markedly enhances estimation accuracy (yellow). With these two sensors, truncated non-causal estimation performs poorly near the trailing edge, whereas causal estimation remains accurate. The inclusion of a third sensor y4y_4 (purple) alongside y5y_5 and y6y_6 results in a slight improvement. The best estimation results are achieved using all four sensors y1y_1, y4y_4, y5y_5, y6y_6 (green). These findings demonstrate greater accuracy than the use of six sensors uniformly distributed on the pressure side of the airfoil, as reported in our previous work [Jung and Towne, 2024].

Figure 15. Estimation error along the trailing edge for spanwise-averaged and mid-span flows using one sensor (y5y_5), two sensors (y5y_5, y6y_6), three sensors (y4y_4, y5y_5, y6y_6), and four sensors (y1y_1, y4y_4, y5y_5, y6y_6).

Figure 16 shows the time-series estimation of streamwise velocity fluctuations using four sensors (y1y_1, y4y_4, y5y_5, y6y_6) for spanwise-averaged (panels aa, dd, gg, jj), mid-span plane (panels bb, ee, hh, kk), and spanwise-Fourier (panels cc, ff, ii, ll) cases. The causal estimation error, computed using (23), is indicated in the bottom right corner of each panel. As expected, the estimation error increases with greater distance between the sensor and the target location. The Wiener–Hopf approach significantly improves estimation accuracy for targets located closer to the trailing edge, as evident in Figure 16(a). The difference in accuracy between truncated non-causal (TNC) and causal methods diminishes as the target moves further downstream. Among the investigated flow types, the spanwise-averaged flow, characterized by less chaotic spatial structures, is estimated most accurately. For the mid-span plane flow, presented in Figure 16 (panels bb, ee, hh, kk), the time-series velocity fluctuations exhibit more random oscillations compared to the other two flow types considered. However, despite this increased complexity, the broader trends in the velocity fluctuations over time are still effectively captured. Although the sensor may not fully capture the detailed footprint of turbulence, the estimation remains effective. These results are consistent with the trends shown in Figure 15.

Figure 16. Estimation of ux′u_x^\prime as a function of time using four sensors (y1y_1, y4y_4, y5y_5, y6y_6): spanwise-averaged (panels aa, dd, gg, jj), mid-span plane (panels bb, ee, hh, kk), spanwise-Fourier cases at kz=10πk_z = 10\pi (panels cc, ff, ii, ll). Target locations are defined by coordinates [z1=x/Lcz_1 = x/L_c, y/Lcy/L_c]: panels (aa–cc) at [1.2, −0.11], (dd–ff) at [1.5, −0.11], (gg–ii) at [2.0, −0.11], and (jj–ll) at [2.5, −0.11], as illustrated in the top figure. The true data from LES are shown in black, causal estimations in blue, and truncated non-causal estimations as magenta dashed lines. The causal estimation error is indicated in red in the bottom right corner of each panel.

Figure 16 (panels cc, ff, ii, ll) displays time-series estimations of the real part of ux′u'_x for the spanwise-Fourier modes with kz=10πk_z = 10\pi. As anticipated, estimation accuracy decreases with increasing spanwise wavenumber. Kernels derived from resolvent operators at frequencies associated with lower energetic gains provide lower estimation accuracy. Since the TNC and causal estimations for the spanwise-Fourier modes yield similar results, the TNC estimations are not shown explicitly in Figure 16 for these cases.

Figure 17 shows three random snapshots of the causal estimation in the extended wake region for spanwise-averaged and mid-span plane cases, using the same sensor configuration as in Figure 16. The estimation errors for the wake region, calculated using metric 4.1, are approximately 0.254 and 0.324 for causal estimation, and 0.352 and 0.389 for truncated non-causal estimation in the spanwise-averaged and mid-span plane cases, respectively. Although the small-scale structures are not fully captured due to the limitations of the sensors in detecting turbulence, the causal resolvent-based estimator effectively estimates the wake fluctuations. Given that the estimation relies solely on a limited number (four sensors) of real-time measurements, these results demonstrate significant promise for practical applications in experimental settings and other engineering scenarios.

Figure 17. LES and estimated snapshots of ux′u_x' across the extended wake region for the spanwise-averaged (panels a, c, e, g, i, k) and mid-span plane (panels b, d, f, h, j, l) flows, utilizing four sensors (y1y_1, y4y_4, y5y_5, y6y_6). The times t1t_1, t2t_2, and t3t_3 were chosen to represent three distinct phases based on the dominant vortex shedding frequency.

Conclusions

In this study, we developed and demonstrated a causal resolvent-based framework for estimating turbulent velocity fluctuations in the wake of a spanwise-periodic NACA0012 airfoil at moderate Reynolds ReLc=23,000Re_{Lc} = 23{,}000, Ma∞≡U∞/c∞=0.3Ma_{\infty} \equiv U_{\infty}/c_{\infty} = 0.3, and an angle of attack of α=6∘\alpha= 6^\circ. Building on previous research focused primarily on a laminar and globally stable flow scenario [30], our approach extended resolvent-based estimation into the more complex regime of a turbulent, globally unstable wake flow.

To address the key challenges inherent in this turbulent regime, including global instabilities, broadband multiscale dynamics, and large datasets, we employed a data-driven approach. This allowed construction of resolvent-based kernels from cross-spectral densities directly obtained via large-eddy simulations, inherently incorporating the colored-in-time statistical properties of nonlinear forcing terms. A key improvement was the adoption of the Wiener–Hopf method to enforce causality [39], which significantly enhanced real-time estimation accuracy compared to traditional truncated, non-causal estimators. To handle computational complexity arising from high-dimensional datasets, our methodology utilized scalable parallel algorithms integrated within an existing compressible flow solver [54] (Jung et al. 2024). Our results illustrated successful causal estimation across spanwise-averaged, spanwise-Fourier, and mid-span plane representations of the turbulent wake, using only limited shear-stress measurements from the airfoil surface. By strategically analyzing single-sensor estimation errors and coherence between sensor and target locations, we identified practical sensor-placement strategies that significantly enhanced estimation fidelity. Ultimately, our approach provided accurate, interpretable, and scalable predictions of an extended portion of the wake, capturing dominant coherent structures crucial for both scientific understanding and potential flow control applications.

Future research directions suggested by this study include developing formal optimization methods for sensor placement and incorporating three-dimensional sensor configurations to further enhance estimation accuracy. The success of the resolvent-based estimation framework suggests that resolvent-based closed-loop flow control strategies could help mitigate turbulent fluctuations, reduce drag, increase lift, and minimize aerodynamic noise. It would also be valuable to investigate the generalizability and robustness of this approach under varying flow conditions, different airfoil geometries, higher Reynolds numbers, and more complex aerodynamic environments. Integrating advanced machine-learning techniques, such as neural networks, into the resolvent-based framework would further improve real-time computational efficiency and effectively handle larger datasets. Finally, experimental validation of the proposed resolvent-based estimation approach in practical wind-tunnel tests or flight scenarios is recommended to confirm its real-world applicability and robustness. By pursuing these avenues, our resolvent-based estimation framework has the potential to significantly advance the predictive modeling, real-time monitoring, and control of complex turbulent aerodynamic flows.

Funding

This research was supported by the Air Force Office of Scientific Research (AFOSR) under grant number FA9550-20-1-0214. Computational resources were provided by the U.S. Department of Defense High-Performance Computing Modernization Program.

Declaration of interests

The authors report no conflict of interest.

Author ORCIDs

Junoh Jung https://orcid.org/0000-0003-0962-3127;

Aaron Towne https://orcid.org/0000-0002-7315-5375.

Wiener-Hopf method

We briefly review the theoretical and numerical Wiener–Hopf decompositions employed for enforcing causality within the resolvent-based estimation and control framework described by Martini et al. [ [39], Audiffred et al. [ [3], Jung et al. [ [30].

Theoretical Wiener-Hopf decomposition

The Wiener-Hopf method [43] decomposes frequency-domain functions into causal (analytic in lower half-plane, (+)(+)) and non-causal (analytic in upper half-plane, (−)(-)) components. This decomposition is employed here to enforce causality on estimation and control kernels, following Daniele and Lombardi [ [12], Martinelli [ [37].

We consider the Wiener-Hopf problem

H^(ω)Γ^+(ω)=Λ^−(ω)+G^(ω),(25)\hat{H}(\omega)\hat{\Gamma}_{+}(\omega)=\hat{\Lambda}_{-}(\omega)+\hat{G}(\omega), \tag*{(25)}

where H^\hat{H} and G^\hat{G} are known matrices, while Γ^+\hat{\Gamma}_{+} and Λ^−\hat{\Lambda}_{-} are unknown.

The Wiener-Hopf method involves additive and multiplicative factorizations, defined as

Γ^(ω)=[Γ^(ω)]−+[Γ^(ω)]+,Γ^(ω)=(Γ^(ω))−(Γ^(ω))+,(26)\hat{\Gamma}(\omega)=[\hat{\Gamma}(\omega)]_{-}+[\hat{\Gamma}(\omega)]_{+},\qquad\hat{\Gamma}(\omega)=(\hat{\Gamma}(\omega))_{-}(\hat{\Gamma}(\omega))_{+}, \tag*{(26)}

respectively. The explicit solution for the above problem is

Γ^+(ω)=[G^(ω)(H^(ω))−−1]+(H^(ω))+−1.(27)\hat{\Gamma}_{+}(\omega)=\left[\hat{G}(\omega)(\hat{H}(\omega))_{-}^{-1}\right]_{+}(\hat{H}(\omega))_{+}^{-1}. \tag*{(27)}

Numerical Wiener-Hopf decomposition

Numerically, the additive factorization is straightforward, while the multiplicative factorization requires solving an integral equation. Following Martini et al. [ [39], this integral equation is given by

x^i(ω)+12iH(x^i)(ω)−12iG^−1(ω)H(G^x^i)(ω)=G^−1(ω)w^i,−(ω0)ω−ω0,(28)\hat{x}_{i}(\omega)+\frac{1}{2\mathrm{i}}\mathcal{H}(\hat{x}_{i})(\omega)-\frac{1}{2\mathrm{i}}\hat{G}^{-1}(\omega)\mathcal{H}(\hat{G}\hat{x}_{i})(\omega)=\hat{G}^{-1}(\omega)\frac{\hat{w}_{i,-}(\omega_{0})}{\omega-\omega_{0}}, \tag*{(28)}

where H\mathcal{H} denotes the Hilbert transform defined by

H(x^)=P.V.1π∫−∞∞x^(u)ω−u du.(29)\mathcal{H}(\hat{x})=\mathop{\mathrm{P.V.}}\frac{1}{\pi}\int_{-\infty}^{\infty}\frac{\hat{x}(u)}{\omega-u}\,\mathrm{d}u. \tag*{(29)}

The reader is referred to Noble [ [43], Daniele and Lombardi [ [12], Martinelli [ [37], Martini et al. [ [39] for a detailed discussion of the Wiener–Hopf method. We numerically solve this integral equation using the GMRES iterative method, implemented directly within the CFD solver. This approach ensures computational efficiency and minimizes the need for external post-processing [30].

Convergence of the data-driven estimation kernels

Constructing estimation kernels using a data-driven approach requires careful selection of discrete Fourier transform (DFT) parameters. Specifically, the streaming Fourier transform [48] depends on several key parameters, including the number of frequencies (NfreqN_{freq}), the number of data blocks (NblkN_{blk}), and the number of overlapping windows (NovlpN_{ovlp}). To reduce spectral leakage between blocks (Nblk)(N_{blk}), we apply a Hamming window with an overlap of 50% [Trethewey, 2000]. Table 2 summarizes a convergence study evaluating how these parameters influence estimation accuracy within the spanwise-averaged flow under best sensor placement conditions. Based on this analysis, parameter set 6 was selected, and these DFT parameters were subsequently applied to the spanwise-Fourier and mid-span plane cases examined in this study.

CaseNfreqN_{freq}NovlpN_{ovlp}NblksN_{blks}Error
15002502960.400748
21,0005001480.350644
32,0001,000740.330292
43,0001,500480.320681
54,0002,000370.320541
65,0002,500290.320422

Table 2. Convergence of the estimation kernels with respect to the parameters for the discrete Fourier Transforms used to compute CSDs.

References

  1. [1]F. R. Amaral and A. V. G. Cavalieri. Large-eddy-simulation-informed resolvent-based estimation of turbulent pipe flow. Phys. Rev. Fluids, 8(7):074606, July 2023. ISSN 2469-990X. doi: 10.1103/PhysRevFluids.8.074606.DOI
  2. [2]F. R. Amaral, A. V. G. Cavalieri, E. Martini, P. Jordan, and A. Towne. Resolvent-based estimation of turbulent channel flow using wall measurements. J. Fluid Mech., 927:A17, November 2021.DOI
  3. [3]D. B. S. Audiffred, A. V. G. Cavalieri, P. P. C. Brito, and E. Martini. Experimental control of Tollmien-Schlichting waves using the Wiener-Hopf formalism. Phys. Rev. Fluids, 8(7):073902, July 2023.DOI
  4. [4]D. B. S. Audiffred, A. V. G. Cavalieri, I. A. Maia, E. Martini, and P. Jordan. Reactive experimental control of turbulent jets. J. Fluid Mech., 994:A15, September 2024. ISSN 0022-1120, 1469-7645. doi: 10.1017/jfm.2024.569.DOI
  5. [5]S. Balay, S. Abhyankar, M. Adams, and Others. Petsc users manual. Argonne National Laboratory, 2019.
  6. [6]R. Bhagwat. Development of stability analysis tools for high speed compressible flows. PhD thesis, 2021.
  7. [10]M. Chevalier, J. Høepffner, T. R. Bewley, and D. S. Henningson. State estimation in wall-bounded flow systems. Part 2. Turbulent flows. J. Fluid Mech., 552(1):167, March 2006. ISSN 0022-1120, 1469-7645. doi: 10.1017/S0022112005008578.
  8. [11]T. Colonius and A. Towne. Chapter 2 - Modal decomposition. In Karthik Duraisamy, editor, Computation and Analysis of Turbulent Flows, pages 27–81. Academic Press, 2025. ISBN 978-0-323-95043-5. doi: https://doi.org/10.1016/B978-0-32-395043-5.00008-5.
  9. [12]V. Daniele and G. Lombardi. Fredholm factorization of Wiener-Hopf scalar and matrix kernels. Radio Science, 42(6):2007RS003673, December 2007.DOI
  10. [13]A. Ducoin, J.-Ch. Loiseau, and J.-Ch. Robinet. Numerical investigation of the interaction between laminar to turbulent transition and the wake of an airfoil. European J. Mech. - B/Fluids, 57:231–248, May 2016. ISSN 09977546. doi: 10.1016/j.euromechflu.2016.01.005.DOI
  11. [14]A. Farghadan, J. Jung, R. Bhagwat, and A. Towne. Efficient harmonic resolvent analysis via time stepping. Theor. Comput. Fluid Dyn., May 2024. ISSN 0935-4964, 1432-2250. doi: 10.1007/s00162-024-00694-1.DOI
  12. [15]A. Farghadan, E. Martini, and A. Towne. Scalable resolvent analysis for three-dimensional flows. J. Comput. Phys., 524:113695, March 2025. ISSN 00219991. doi: 10.1016/j.jcp.2024.113695.DOI
  13. [16]P. F. Fischer, J. W. Lottes, and S. G. Kerkemeier. Nek5000: Open source spectral element cfd solver, 2008.
  14. [17]M. Frigo and S. G. Johnson. The Design and Implementation of FFTW3. Proc. IEEE, 93(2):216–231, February 2005.DOI
  15. [18]I. S. Gartshore. Two-dimensional turbulent wakes. J. Fluid Mech., 30(3):547–560, November 1967. ISSN 0022-1120, 1469-7645. doi: 10.1017/S0022112067001600.DOI
  16. [19]S. Ghaemi and F. Scarano. Counter-hairpin vortices in the turbulent wake of a sharp trailing edge. J. Fluid Mech., 689:317–356, December 2011. ISSN 0022-1120, 1469-7645. doi: 10.1017/jfm.2011.431.DOI
  17. [20]S. Gupta, J. Zhao, A. Sharma, A. Agrawal, K. Hourigan, and M. C. Thompson. Two- and three-dimensional wake transitions of a NACA0012 airfoil. J. Fluid Mech., 954:A26, January 2023. ISSN 0022-1120, 1469-7645. doi: 10.1017/jfm.2022.958.DOI
  18. [21]R. W. Hamming. Digital filters. Dover Publications, 1997.
  19. [22]M. Hočevar, B. Širok, and I. Grabec. A Turbulent-Wake Estimation Using Radial Basis Function Neural Networks. Flow Turbul. Combust., 74(3):291–308, April 2005. ISSN 1386-6184, 1573-1987. doi: 10.1007/s10494-005-5728-4.DOI
  20. [23]B. Jin, S. J. Illingworth, and R. D. Sandberg. Optimal sensor and actuator placement for feedback control of vortex shedding. J. Fluid Mech., 932:A2, February 2022.DOI
  21. [24]M. R. Jovanović and B. Bamieh. Componentwise energy amplification in channel flows. J. Fluid Mech., 534:145–183, June 2005.DOI
  22. [26]J. Jung and A. Towne. Toward turbulent wake estimation using a resolvent-based approach. AIAA Paper #2024-0057, 2024.DOI
  23. [27]J. Jung, E. Martini, A. Cavalieri, P. Jordan, L. Lesshaft, and A. Towne. Optimal resolvent-based estimation for flow control. APS Division of Fluid Dynamics, G06:004, 2020.
  24. [28]J. Jung, R. Bhagwat, and A. Towne. Resolvent-based estimation of laminar flow around an airfoil. AIAA Paper #2023-0077, 2023.DOI
  25. [30]J. Jung, R. Bhagwat, and A. Towne. Resolvent-based estimation and control of a laminar airfoil wake. J. Fluid Mech., 0, 2025. doi: 10.1017/jfm.2025.10423.DOI
  26. [31]R.E. Kalman. A new approach to linear filtering and prediction problems. J. Basic Eng., 82:35–45, 1960.DOI
  27. [32]D.-H. Kim, J.-H. Yang, J.-W. Chang, and J Chung. Boundary layer and near-wake measurements of naca 0012 airfoil at low reynolds numbers. AIAA Paper #2009-1472, 2009.DOI
  28. [33]R. Kojima, T. Nonomura, A. Oyama, and K. Fujii. Large-Eddy Simulation of Low-Reynolds-Number Flow Over Thick and Thin NACA Airfoils. J. Aircraft, 50(1):187–196, 2013.
  29. [34]Q. Liu, Y. Sun, C. Yeh, L. S. Ukeiley, L. N. Cattafesta, and K. Taira. Unsteady control of supersonic turbulent cavity flow based on resolvent analysis. J. Fluid Mech., 925:A5, October 2021. ISSN 0022-1120, 1469-7645.
  30. [35]I. A. Maia, P. Jordan, A. V. G. Cavalieri, E. Martini, K. Sasaki, and F. J. Silvestre. Real-time reactive control of stochastic disturbances in forced turbulent jets. Phys. Rev. Fluids, 6(12):123901, December 2021. ISSN 2469-990X. doi: 10.1103/PhysRevFluids.6.123901.
  31. [36]K. Manohar, B. W. Brunton, J. N. Kutz, and Brunton S. L. Data-Driven Sparse Sensor Placement for Reconstruction: Demonstrating the Benefits of Exploiting Known Patterns. IEEE Control Syst., 38(3):63–86, June 2018. ISSN 1066-033X, 1941-000X. doi: 10.1109/MCS.2018.2810460.DOI
  32. [37]F. Martinelli. Feedback Control of Turbulent Wall Flows. PhD thesis, 2009.
  33. [38]E. Martini, A. V. G. Cavalieri, P. Jordan, A. Towne, and L. Lesshafft. Resolvent-based optimal estimation of transitional and turbulent flows. J. Fluid Mech., 900:A2, October 2020. ISSN 0022-1120, 1469-7645.DOI
  34. [39]E. Martini, J. Jung, A. Cavalieri, P. Jordan, and A. Towne. Resolvent-based tools for optimal estimation and control via the Wiener–Hopf formalism. J. Fluid Mech., 937:A19, April 2022.
  35. [40]B. J. McKeon and A. S. Sharma. A critical-layer framework for turbulent pipe flow. J. Fluid Mech., 658: 336–382, September 2010.DOI
  36. [41]P. M. Munday and K. Taira. Effects of wall-normal and angular momentum injections in airfoil separation control. AIAA J., 2018.arxiv.org/abs/1711.09469
  37. [42]E. J. Nielsen and W. L. Kleb. Efficient construction of discrete adjoint operators on unstructured grids using complex variables. AIAA J., 2006.DOI
  38. [43]B. Noble. Methods Based on the Wiener-Hopf Technique for the Solution of Partial Differential Equations, volume 7 of Int. Ser. Monogr. Pure Appl. Math. Pergamon Press, New York, 1958.
  39. [44]W. C. Reynolds. Large-scale instabilities of turbulent wakes. J. Fluid Mech., 54(3):481–488, August 1972. ISSN 0022-1120, 1469-7645. doi: 10.1017/S0022112072000813.DOI
  40. [45]P. Sashittal and D. J. Bodony. Data-driven sensor placement for fluid flows. AIAA Paper #2021-2824, 2021.
  41. [46]C. J. Schauerte and A. Schreyer. Experimental investigation on the turbulent wake flow in fully established transonic buffet conditions. CEAS Aeronautical J., 15(1):125–147, January 2024. ISSN 1869-5582, 1869-5590. doi: 10.1007/s13272-023-00690-x.DOI
  42. [47]P. J. Schmid and D. Sipp. Linear control of oscillator and amplifier flows. Phys. Fluids, 1(4):040501, August 2016. ISSN 2469-990X.
  43. [48]O. T. Schmidt and A. Towne. An efficient streaming algorithm for spectral proper orthogonal decomposition. Comput. Phys. Communi., 237:98–109, April 2019. ISSN 00104655. doi: 10.1016/j.cpc.2018.11.009.DOI
  44. [49]S. Shamsoddin and F. Porté-Agel. Turbulent planar wakes under pressure gradient conditions. J. Fluid Mech., 830:R4, November 2017. ISSN 0022-1120, 1469-7645. doi: 10.1017/jfm.2017.649.DOI
  45. [50]V. Theofilis. Advances in global linear instability analysis of nonparallel and three-dimensional flows. Prog. in Aerosp. Sci., 39(4):249–315, May 2003. ISSN 03760421. doi: 10.1016/S0376-0421(02)00030-1.DOI
  46. [51]A. Towne, O. T. Schmidt, and T. Colonius. Spectral proper orthogonal decomposition and its relationship to dynamic mode decomposition and resolvent analysis. J. Fluid Mech., 847:821–867, July 2018.DOI
  47. [52]A. Towne, A. Lozano-Durán, and X. Yang. Resolvent-based estimation of space–time flow statistics. J. Fluid Mech., 883:A17, January 2020. ISSN 0022-1120, 1469-7645.DOI
  48. [53]A. Towne, S. T. M. Dawson, G. A. Brès, A. Lozano-Durán, T. Saxton-Fox, A. Parthasarathy, A. R. Jones, H. Biler, C. Yeh, H. D. Patel, and K. Taira. A database for reduced-complexity modeling of fluid flows. AIAA J., 2023.
  49. [54]A. Towne, R. Bhagwat, Y. Zhou, J. Jung, E. Martini, P. Jordan, D. Audiffred, I. Maia, and A. Cavalieri. Resolvent-based estimation of wavepackets in turbulent jets. AIAA Paper #2024-3413, 2024.DOI
  50. [56]C. Yeh and K. Taira. Resolvent-analysis-based design of airfoil separation control. J. Fluid Mech., 867: 572–610, May 2019. ISSN 0022-1120, 1469-7645.DOI
  51. [57]C. Yeh, S. I. Benton, K. Taira, and D. J. Garmann. Resolvent analysis of an airfoil laminar separation bubble at Re = 500 000. Phys. Rev. Fluids, 5(8):083906, August 2020. ISSN 2469-990X.arxiv.org/abs/2007.16197
  52. [58]A. Ying, T. Liang, Z. Li, and L. Fu. A resolvent-based prediction framework for incompressible turbulent channel flow with limited measurements. J. Fluid Mech., 976:A31, December 2023. ISSN 0022-1120, 1469-7645. doi: 10.1017/jfm.2023.867.DOI

Paper details

vlnc:W_kf7a4yh8
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 5

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents