WorksPhysics and Astronomy
CMOS compatible multi-band plasmonic TE-pass polarizer
Abstract
A CMOS-compatible plasmonic TE-pass polarizer capable of working in the O, E, S, C, L, and U bands is numerically analyzed. The device is based on an integrated hybrid plasmonic waveguide (HPW) with a segmented metal design. The segmented metal will avoid the propagation of the TM mode, confined in the slot of the HPW, while the TE fundamental mode will pass. The TE mode is not affected by the metal segmentation since it is confined in the core of the HPW. The concept of the segmented metal can be exploited in a plasmonic circuit with HPWs as the connecting waveguides between parts of the circuit and in a silicon photonics circuit with strip or slab waveguides connecting the different parts of the circuit. Using 3D FDTD simulations, it is shown that for a length of 5.5 μm the polarization extinction ratios are better than 20 dB and the insertion losses are less than 1.7 dB over all the optical communication bands.
OCIS codes: (130.0130) Integrated optics; (130.3120) Integrated optics devices; (130.5440) Polarization-selective devices; (250.5403) Plasmonics; (130.1750) Components.
Introduction
For many applications of silicon photonic integrated circuits, polarization handling devices are needed. One example is for polarization diversity circuits like the ones used for optical interconnects, when edge coupling is employed. An important task of polarization diversity circuits is to handle polarization dependent loss and polarization mode dispersion which comes from the polarization dependence of the large birefringence in the silicon-on-insulator (SOI) platform. Another use of it is in separating the different polarizations, for example, in a coherent optical receiver. These functions are handled using devices like polarization beam splitters (PBS) and polarization rotators [1, 2].
Another simpler approach is to design the circuit for one polarization [3] and avoid the other with a device like a TE- or TM-pass polarizer. In such a case, polarization division multiplexing cannot be exploited, but the circuit is simplified. It is well known that dispersion compensating filters [4] in integrated optics only work with one polarization, mainly TE. Normally, to introduce only one polarization into the circuit a bulk circulator and PBS are used [5, 6, 7]. When the TE mode is desired, then, a TE-pass polarizer can be placed at the input of the dispersion compensating filter avoiding both the PBS and the circulator. Consequently, a simple and compact TE-pass polarizer is needed.
Other important applications for pass polarizers are in the domain of quantum communications, optical sensing, and polarization filters. It is advantageous that the integrated TE-pass polarizer is Complementary metal–oxide–semiconductor (CMOS) compatible to leverage existing nanofabrication processes, mass production, and also be compatible with silicon photonic integrated circuits. With CMOS compatibility, we refer to the possibility of production in a state-of-the-art CMOS foundry [8]. The desired characteristics of a TE-pass polarizer are a high polarization extinction ratio (), low insertion loss (IL) and, depending on the application, a broad bandwidth. A typical value for the is roughly 20 dB, for the IL less than 2-3 dB and the bandwidth more than 150-200 nm [9]. The wide bandwidth is not only important for the coherent optical receiver or to handle WDM and OFDM signals, but also, it will be useful if the TE-pass polarizer can work in all the well-known bands exploited by silicon photonics (O, E, C, S, and L) with the same simple structure. There are many applications of silicon photonics in the O, E, C and L [10, 11] bands. Other applications -includes the S and U bands [12] in wavelength converters.
Over the years, several CMOS compatible integrated polarizers have been proposed. They have either been all dielectric [2, 13] or plasmonic. The advantage of plasmonic polarizers is that they are typically more compact. On the other hand, plasmonic-based integrated polarizers suffer from higher losses due to the absorption of the optical field by the metal. Furthermore, the most common materials for plasmonics are silver (Ag) or gold (Au) are not CMOS compatible [9]. Many TE- or TM-pass polarizers using those non-CMOS compatible materials have been previously studied [15, 16, 17, 18, 19, 20, 21].
There are many plasmonic polarizers [15, 16, 17, 18, 19, 20, 21] that are excited form a photonic waveguide. Nevertheless, it will be interesting that a plasmonic polarizer can also be excited from a plasmonic waveguide [22] using the same structure as used for the photonic circuit. A photonic circuit is a circuit in which the devices are connected by photonic waveguides, like the strip or slab silicon (Si) photonics waveguide. In the same way, a plasmonic circuit refers to a circuit in which the different devices in the circuit are connected by plasmonic waveguides, like the hybrid plasmonic waveguide (HPW).
Many CMOS compatible integrated plasmonic polarizers have been recently shown. The TE-pass polarizer in [3] is an experimental demonstration that has a high measured insertion loss of around 4 dB when excited from a standard Si waveguide. However, when excited from a horizontal nano-plasmonic slot waveguide the measured insertion loss is around 2.2 dB. One disadvantage of this structure is that it has a difficult fabrication since some fabrication features are below 193 nm deep-UV lithography [8] limit. In [23], a TM-pass polarizer compatible with standard CMOS fabrication process is demonstrated. Nevertheless, it has a moderate polarization extinction ratio of around 13 dB. Continuing with the recent trend of using new materials for plasmonics [14] the CMOS compatible TE-pass polarizer analyzed in [24] offers a polarization extinction ratio of 20 dB with a very low insertion loss of around 0.0635 dB in a very compact footprint with a length of 3.5 m. Nevertheless, this device also has dimensions below the minimum resolution of 193 nm deep-UV lithography [8] and adds new materials in the fabrication. The device has a bandwidth of 150 nm for an extinction ratio better than 15 dB [24] extending the length to 5.5 m. The work presented in [25] has a limited bandwidth. Finally, in [26] a bandwidth of 300 nm is reported, but the device is excited from a slot waveguide.
Most of them have in common that they only operate in one band or they have limited bandwidth. To the best of our knowledge there is no TE-pass polarizer capable of working across the different optical communications bands O (1.26 μm - 1.36 μm), E (1.36 μm - 1.46 μm), S (1.46 μm - 1.53 μm), C (1.53 μm - 1.565 μm), L (1.565 μm - 1.625 μm), and U (1.625 μm - 1.675 μm) with the same simple structure and being able to be excited from a photonic and/or a plasmonic waveguide. Most of the designs, except [3], are only excited from a photonic waveguide.
In this work, a TE-pass polarizer based on a vertical hybrid plasmonic waveguide (HPW) [27] is presented. The metal of the HPW is segmented to diffract the TM mode and pass the TE mode. Such a TE-pass polarizer is CMOS compatible and can operate in several bands of a photonic circuit (excited by a Si strip waveguide) with a polarization extinction ratio better than 20 dB and the insertion losses below 1.7 dB over all the optical communication bands. The same concept can also be excited from an HPW to be exploited in a plasmonic circuit.
Operational principle and design decisions
In this section, the operational principle of the device, the design decisions, and the optimization process are described. The first decision was to use an HPW [21] since it is one of the most promising candidates for a plasmonic circuit [28].
A TE-pass polarizer can be done with an HPW with a continuous metal. In this kind of waveguides, the TM fundamental mode, like the one in Figure 1(a), has a higher absorption loss than the TE mode, like the one represented in Fig. 1(b) due to the metal.

Figure 1. Example of an electric field of the TE (a) and TM mode (b) in an HPW. The slot is made of SiO. The TE mode is concentrated in the Si core while the TM mode is concentrated in the slot and the interface between the metal and the slot. The wavelength is 1550 nm.
Hence, the TM to extinguish more than the TE mode as they propagate along the HPW. Nevertheless, due to the not so big difference in absorption losses between TE and TM, this would result in a long TE-pass polarizer of several mm.
For reducing the length of such a TE-pass polarizer, in this work, the metal was segmented to diffract the TM mode. The TM mode is confined mostly close to the metal of the waveguide-like in Figure 1(b) and is highly affected by the grating. On the other hand, TE is far from the grating, and it is not highly affected.
If the metal is segmented, the TM mode diffracts due to the grating effect. On the other hand, the TE mode is relative away from the metal, and it is not affected by the grating.
The structure of the proposed device is represented in Figure 2. The TE-pass polarizer to work in the plasmonic circuit represented in Figure 2(a) is excited by an input HPW and the light is collected by an output HPW, between them, the metal was segmented to form the TE-pass polarizer structure. On the other hand, for the device to work in a photonic circuit, it is excited by an input Si strip waveguide and the light is collected by an output Si strip waveguide. Between them, the TE-pass polarizer consists of an HPW with the metal segmented.

Figure 2. Structure of the TE-pass polarizer. In (a) excited by a plasmonic waveguide. In (b) excited by a photonic waveguide.
This diffraction effect produced by the segmentation of the metal in the device is depicted in Figure 3(a) and Figure 3(b) for a plasmonic circuit and in Figure 3(c) and Figure 3(d) for a photonic circuit. These Figs. represent the complete optimized TE-pass polarizer whose optimization will be detailed in the next section.

Figure 3. The electric field of the TE mode passing through the TE-pass polarizer (a) in a plasmonic circuit. In (b), the electric field of the TM mode being filtered by the TE-pass polarizer. In (c), there is the electric field of the TE mode passing the TE-pass polarizer while in (d) the TM mode is filtered. The wavelength is 1550 nm.
In Figure 3, the TE mode passes while the TM mode does not. The parameters of the TE-pass polarizer in Figure 3 were optimized as will be described in the next section.
In the following section, it is explained how the optimization of the TE-pass polarizer was done regarding materials and parameters.
Optimization of the TE-pass polarizer
In this section, we present the optimization process done to design the structure. As a first step, we selected the material for the structure, then, we optimized the parameters of the structure (, , and ). To simplify we selected .
Regarding the selection of the materials, as the core of the waveguide, we selected Si to be compatible with the Silicon Photonics platform [8]. To be CMOS compatible, and leverage existing microelectronic fabrication processes, we need to select between Aluminum (Al) and Copper (Cu) for the metal [8] of the HPW. Since Cu has less optical losses than Al [10, 11], we selected Cu. Regarding the diffusion barrier for the slot, there are many possibilities: Ta, TaN, Ti, TiN, SiN, and SiO [29].
To select the material, we performed 2D simulations with MODE solutions of Lumerical [30]. The analysis was performed in the cross section of an HPW to try to maximize the difference in optical losses between the absorption loss of the mode and the absorption loss of the mode . The value is related to the polarization extinction ratio of the device (PER) by multiplying by the length of the TE-pass polarizer (when the metal is continuous). The polarization extinction ratio is defined as the ratio of the power in the TE mode at the output of the TE-pass polarizer divided by the power of the TM mode at the output of such a polarizer. The final expression is . The final relation is . Hence, a large is desired.
On the other hand, the parameter is related to the insertion loss (IL) of the device when it is multiplying by the length of the polarizer (when the metal is continuous). The insertion loss is defined as the power in the TE mode at the output divided by the power of the TE mode at the input . The final relation is . Hence, a small value of is desired.
Consequently, for the optimization of the cross-section of the HPW, we selected the Figure of Merit (FoM) equal to to maximize the polarization extinction ratio and reduce the insertion loss of the TE-pass polarizer.
The main parameters that influence , and are the width of the Si core , the height of the Si core and the thickness of the slot as shown in Figure 2. Consequently, we studied the versus the parameters , , and . For fabrication reasons, we compared the slots with the following materials: SiO, SiN, Ta, and Ti [29]. The analysis is presented in Figure 4.

Figure 4. Study of the FoM = for the different parameters of the HPW , and with a SiO (a), SiN (b), Ta (c) and Ti (d). Typical parameters for , and are used.
In Figure 4(a)–Figure 4(d) we scanned the parameter from 3 nm (minimum fabrication thickness [10, 11, 29]) to 20 nm until a maximum is reached for an intermediate . The parameters and are scanned from 250 nm to 500 nm which are common values for the HPW [10, 29].
In Figure 4(a) the FoM is represented versus and for four different values: 3 nm, 5 nm, 10 nm and 20 nm. It is possible to observe that the maximum FoM is reached for nm. The maximum value of the FoM is 10.
In the case of Figure 4(b) with the slot of SiN, the same study is done, and a maximum value of the FoM is reached for nm. Finally, for Ta in Figure 4(c) and Ti in Figure 4(d) the maximum value reached is for nm in both cases.
In all cases, in Figure 4 the FoM increases when and are increased. Since the TE mode is concentrated in the Si core, if we increase , the mode is farther away from the metal which will reduce the optical losses of the TE mode . This will increase the FoM . On the other hand, in a waveguide when you increase the modes have less optical losses, increasing reduces so that increases with . On the other hand, the TM mode loss strongly depends on [10]. On the contrary, the losses of the TE mode does not depend strongly on because the field is not confined in the slot. The relation between the optical loss of the mode and the effective index of the material used can be found in [31].
Finally, for fabrication reasons, we have decided to employ SiO in the rest of the study. Although using SiN, Ta, or Ti may result in a similar performance. Selecting SiO in the slot will fix the parameter to nm to obtain the maximum FoM. Now, it will be necessary to fix and . If we select the biggest values for and that are 500 nm, then the waveguide will be highly multimode. To avoid that, we fixed nm and nm. With such dimensions, there is only TE and multimode TM modes (TM, TM, and TM). High order TM modes will also be filtered by the structure. The final optimized parameters of the cross section are nm, nm, and nm (SiO). The optimization of is the last parameter to be optimized.
Optimization of in the TE-pass polarizer
In this section, we study the performance of the TE-pass polarizer with the HPW previously optimized and with continues metal. Later, we segmented the metal of the HPW, and the parameter is optimized.
For the optimized values of the cross-section of the HPW the effective index of the photonic TE fundamental mode is , and the absorption loss is dB/m. Regarding the plasmonic TM fundamental mode the effective index is and the absorption loss is dB/m. To calculate the polarization extinction ratio, we use the formula PER and for the insertion loss, we use the formula IL , where is the length of the HPW. The results are shown in Figure 5.

Figure 5. Estimated polarization extinction ratio and insertion loss of a TE-pass polarizer with continues metal which consists of an HPW of length . The dimensions of the HPW are nm, nm and nm (SiO). The wavelength is 1550 nm.
With this device, 20 m are needed to obtain an extinction ratio of 4 dB. By segmenting the metal, the device can be shortened.
To optimize the last parameter , it is needed to calculate the length of the TE-pass polarizer and the optimum size of the metal segments . To do this, we performed 3D FDTD simulations using Lumerical [30].
For the initial simulations, we selected minimum value for around 0.3 m to use lift-off in the fabrication process. On the other hand, the maximum value of was set to 1 m to have a compact TE-pass polarizer still. To further complete the scanning, we also selected an intermediate value of around 0.5 m. To agree with the grating theory, we selected the period of the grating with .
Using the FoM as previously explained, the result of the 3D FDTD simulation is presented in Figure 6(a).

Figure 6. Estimation of the of the TE-pass polarizer with a segmented metal of (a) The wavelength is fixed to 1550 nm and the HPW have the optimized values. In (b) the spectrum of the TE-pass polarizer with m and m.
In Figure 6(a), the maximum of the is for m. As one of the requirements for a TE-pass polarizer is to have a polarization extinction ratio around 20 dB, we selected a minimum length of m. The final parameters are summarized in Table 1.
| Parameter: | |||||
| Value: | 450 nm | 400 nm | 5 nm | 0.5 m | 5.5 m |
Table 1. Summary of the optimized parameters of the TE-pass polarizer with the HPW.
With the values summarized in Table 1, we calculated the spectrum of the TE-pass polarizer with the segmented metal for the wavelength window from 1.1 m to 2 m. The estimation is shown in Figure 6(b). In such a case, we included the higher order plasmonic TM modes named TM and TM. It is possible to observe that TM and TM are also filtered.
To the propagation of TM and TM in represented it in Figure 7(a) and Figure 7(b).

Figure 7. Filtering of TM (a) and TM (b) for the optimized TE-pass polarizer with nm, nm, nm (SiO), m, and m for 1550 nm.
The optimized performance of the TE-pass polarizer is summarized in Table 2.
| Band: | O | E | S | C | L | U |
| Polarization extinction ratio: | 20 dB | 20 dB | 21 dB | 20 dB | 18 dB | 22 dB |
| Insertion loss: | 0.7 dB | 1 dB | 1.3 dB | 1.3 dB | 1.5 dB | 1.7 dB |
| Wavelength: |
Table 2. Performance of the TE-pass polarizer in a plasmonic circuit.
In the C-band, the polarization extinction ratio is around 20 dB for an IL = 1.3 dB at 1.55 for 0.5 which is better than using a continuous metal.
As a summary, we optimized the cross-section of the HPW of the TE-pass polarizer using 2D simulations solutions [30]. With this, we calculated nm, nm and nm (SiO). After that, we performed 3D FDTD simulations to calculate the parameter and to obtain a polarization extinction ratio better than 20 dB at 1550 nm.
It will be interesting to check the simulations by scanning the cross-section of the HPW using 3D FDTD simulations to see if they agree with the 2D simulations. For this, we fixed nm (SiO), , and . And we scanned and . The results of the 3D FDTD estimation is represented in Figure 8. To scan all the parameters in 3D is not computationally affordable in a reasonable time.

Figure 8. Scanning and in 3D FDTD for nm (SiO), , and at 1550 nm. This scan is performed to know if the results are like the results in 2D represented in Figure 4(a).
In Figure 8, the trend is the same as in Figure 4(a). Consequently, we have validated the 2D approximation we did. It means when we increase , increases. It has the same trend as Figure 4(a). In the same manner, when we increase , increases.
To conclude this section, we have analyzed the performance of the TE-pass polarizer with segmented metal for different optical bands in a plasmonic circuit. Now, it will be interesting to exploit the same device in a photonic circuit from which the TE-pass polarizer will be excited from a photonic strip waveguide.
Performance of TE-pass polarizer in a photonic circuit
In this section, we calculate the optimization of the TE-pass polarizer to be excited from a photonic waveguide. The structure is presented in Figure 1(b) and it consists of an input Si strip waveguide to excite the device, the TE-pass polarizer consisting of segmented metals and an output Si strip waveguide to collect light. The dimensions of the Si strip waveguide employed are nm and nm. The modes of such waveguide are represented in Figure 9.

Figure 9. Modes supported by a Si strip waveguide of nm and nm. In (a) the electric field of , in (b) the mode. in (c) and in (d).
The TE mode is represented in Figure 9(a) and it will be passing the TE-pass polarizer. On the other hand, the TM modes in Figure 4(b)–Figure 4(d) will be filtered by the device.
In this section, we employed the same optimized values for the device. It means, the parameters of the cross-section of the HPW are nm, nm, and nm (). The metal was segmented with m. Regarding the dimension of the input/output strip waveguides, we have selected nm and nm to butt-couple it to the device.
The bandwidth of the TE-pass polarizer is represented in Figure 10(a). For comparison, in Figure 10(b) we placed the bandwidth of a TE-pass with continuous metal using the same dimensions.

Figure 10. Bandwidth of the TE-pass polarizer with segmented metal with the optimized values (a) and the same TE-pass polarizer with an HPW of continuous metal (b).
By comparing Figure 10(a) and Figure 10(b) we can observe that the polarization extinction ratio of the TE-pass polarizer with segmented metal is larger for a similar insertion loss at 1550nm. Consequently, by segmenting the metal, the polarization extinction ratio is incremented while reducing the length of the device.
As shown before, the mode of the Si strip waveguide passes the structure as represented in Figure 3(c) and the fundamental TM mode of the Si strip waveguide is filtered by the device as shown in Figure 3(d). On the other hand, the higher order TM modes, and , supported by the input Si strip waveguide are also filtered. This is exemplified in Figure 11.

Figure 11. Optimized TE-pass polarizer with segmented metal for a photonic circuit for (a) and (b) at 1550 nm.
The performance is summarized in Table 3 for the different optical communication bands.
| Band | O | E | S | C | L | U |
| Polarization extinction ratio | 20.5 dB | 21 dB | 20.9 dB | 19.3 dB | 19.5 dB | 27.2 dB |
| Insertion loss | 1.5 dB | 1.5 dB | 1.6 dB | 2.2 dB | 2.5 dB | 2.8 dB |
| Wavelength | 1.31 m | 1.4 m | 1.5 m | 1.55 m | 1.6 m | 1.65 m |
Table 3. Performance of the TE-pass polarizer in the different optical bands.
As a final step, we did a further analysis of the period in Figure 12. We scanned the period in intermediate points to know if there is another better period. In Figure 12(a) we presented the transmission of different periods between 0.5 m and 1.5 m. To compare all of them we calculated the in Figure 12(b). It is possible to observe that = 1 m has the best behavior regarding the bandwidth. On the other hand, it is only better by = 0.5 m in the C-band. Nevertheless, for = 0.5 m we have a = 0.25 m which is at the limit of the lift-off resolution.
Figure 12. Scanning the period of the optimized plasmonic TE-pass polarizer. In (a) the transmission of the TE and TM modes and in (b) the FoM = . The dots in Figure 12(a) are the points selected to study the grating behavior.
From Figure 12(a) it is possible to observe that the TM mode has a valley that depends on the wavelength. We marked it with black dots. We checked that the valley shifts according to the following formula:
Where is the estimated period of the grating, is the order of the grating, is the wavelength of the valley in transmission, and is the effective index of TM mode at the wavelength . The results are summarized in Table 4. It is possible to observe that the simulations follow the grating behavior. This confirms that the device is diffracting the TM mode. The same happens with TM and TM.
| [μm] | [μm] | [μm] | ||
| 0.5 | 1.575 | 2.91 | 2 | 0.54 |
| 0.75 | 1.63 | 2.83 | 3 | 0.84 |
| 1.0 | 1.55 | 2.85 | 4 | 1.08 |
| 1.25 | 1.475 | 2.99 | 5 | 1.23 |
| 1.5 | 1.56 | 2.91 | 6 | 1.59 |
Table 4. Estimation of the period of the grating.
Comparison with the state-of-the-art
In this section, the proposed device is compared with the CMOS compatible plasmonic TE-pass polarizers reported until now. The main parameters, like the polarization extinction ratio, the insertion loss, and the bandwidth are discussed. The parameters are summarized in Table 5.
| Group: | A*STAR [3] (2013) | Mansoura [24] (2016) | Southeast [25] (2016) | Huazhong [26] (2016) | Us |
| Polarization extinction ratio | 16 dB | 20 dB | 34.74 dB | 41.62 dB | 19.3 dB |
| Insertion loss | 4 dB* | 0.06350 dB | 0.43 dB | 0.38 dB | 2.2 dB |
| Length | 4 μm | 3.5 μm | 8 μm | 3 μm | 5.5 μm |
| Bandwidth | 80 nm | 150 nm** | 250 nm | 300 nm | 500 nm (E, S, C, L, S and U bands***) |
| Type of work | Experimental | Theoretical | Theoretical | Theoretical | Theoretical |
Table 5. Comparison with the state-of-the-art of CMOS compatible TE-pass polarizers at 1.55μm.
In conclusion, our structure offers a larger extinction ratio and a smaller insertion loss than the experimental work presented in [3].
*From [1] when excited from a Si strip waveguide.
** From Figure 4(a) [24] when the polarization extinction ratio is 15 dB (5 dB less than the maximum of 20 dB). The device is 3.5 μm, but we took 5.5 μm (like ours), and we scaled the ER and IL linearly.
***For a polarization extinction ratio bigger than 22 dB.
On the other hand, the work presented by Mansoura [24] has an excellent trade-off regarding the polarization extinction ratio and the insertion loss. Nevertheless, it has a limited bandwidth of 150 nm (for a polarization extinction ratio bigger than 15 dB and a length of 5.5 μm). Furthermore, this structure presents features smaller than the minimum resolution of 193 nm deep-UV lithography.
The work in [25] has limited bandwidth, and the structure is not simple to fabricate since it involves the fabrication of a thin layer of ITO in the middle of the strip Si waveguide.
Finally, the device proposed in [26] has an excellent trade-off between and but the bandwidth is limited, and it is excited from a slot waveguide.
One of the advantages of our device is that it offers the possibility of working in the O, E, S, C, L, and U bands with an acceptable polarization extinction ratio and moderate insertion loss with the same simple structure. Such a concept can be exploited both in a plasmonic circuit and in a photonic circuit. This concept can be extended to TM-pass polarizers like in [32].
Conclusion
In this work, the design and optimization of a novel plasmonic CMOS compatible TE-pass polarizer were presented. To design the device, we optimized its most important parameters using 2D and 3D FDTD simulations. The device works in several optical bands with the same simple CMOS compatible structure being the main novelty of the device the segmented metal of the HPW. This allows to pass of the TE mode and blocks the TM modes. This TE-pass polarizer can work in the traditional communication bands for silicon photonics: O, E, S, C, L, and U with the same structure.
Funding
EPSRC (EP/P006973/1).
Acknowledgments
We would like to acknowledge CMC Microsystems for the provision of products and services that facilitated this research, including Lumerical. We are grateful for support from the Future Compound Semiconductor Manufacturing Hub (CS Hub) funded by EPSRC grant reference EP/P006973/1.
References
- [1]N. Abadía, X. Dai, Q. Lu, W.-H. Guo, D. Patel, D. V. Plant, and J. F. Donegan, “Highly fabrication tolerant InP based polarization beam splitter based on p-i-n structure,” Opt. Express 25(9), 10070–10077 (2017).
- [2]N. Abadia, Xiangyang Dai, Q. Lu, W.-H. Guo, E. El-Fiky, D. V. Plant, and J. F. Donegan, “Novel polarization beam splitter based on p-i-n structure for an indium phosphide platform,” in 2017 19th International Conference on Transparent Optical Networks (ICTON, 2017), paper Th.A5.1.DOI
- [3]Y. Huang, S. Zhu, H. Zhang, T.-Y. Liow, and G.-Q. Lo, “CMOS compatible horizontal nanoplasmonic slot waveguides TE-pass polarizer on silicon-on-insulator platform,” Opt. Express 21(10), 12790–12796 (2013).DOI
- [4]K. Takiguchi, K. Okamoto, S. Suzuki, and Y. Ohmori, “Planar lightwave circuit (optical dispersion equalizer),” IEEE Photonics Technol. Lett. 6(1), 86–88 (1994).DOI
- [5]C. R. Doerr, K. W. Chang, L. W. Stultz, R. Pafchek, O. G. Luo, L. Buhl, L. Gomez, M. Capuzzo, and G. Bogert, “Arrayed waveguide dynamic gain equalization filter with reduced insertion loss and increased dynamic range,” IEEE Photonics Technol. Lett. 13(4), 329–331 (2001).DOI
- [6]K. Takiguchi, H. Takahashi, and T. Shibata, “Tunable chromatic dispersion and dispersion slope compensator using a planar lightwave circuit lattice-form filter,” Opt. Lett. 33(11), 1243–1245 (2008).pubmed.ncbi.nlm.nih.gov/18516188
- [7]K. Takiguchi, K. Jinguji, K. Okamoto, and Y. Ohmori, “Variable Group-Delay Dispersion equalizer using lattice-form programmable optical filter on planar lightwave circuit,” IEEE J. Sel. Top. Quantum Electron. 2(2), 270–276 (1996).DOI
- [8]J. S. Ouritt, B. Moss, C. Sun, J. Leu, M. Georgas, J. Shainline, E. Zgraggen, H. Li, J. Sun, M. Weaver, S. Urošević, M. Popović, R. J. Ram, and V. Stojanović, “Open foundry platform for high-performance electronic-photonic integration,” Opt. Express 20(11), 12222–12232 (2012).DOI
- [9]D. Thomson, A. Zilkie, J. E. Bowers, T. Komljenovic, G. T. Reed, L. Vivien, D. Marris-Morini, E. Cassan, L Virot, J.-M. Fédéli, J.-M. Hartmann, J. H. Schmid, D.-X. Xu, F. Boeuf, P. O’Brien, G. Z. Mashanovich, and M. Nedeljkovic, “Roadmap on silicon photonics,” J. Opt. 18(7), 073003 (2016).DOI
- [10]N. Abadía, T. Bernadin, P. Chaisakul, S. Olivier, D. Marris-Morini, R. Espiau de Lamëastre, J. C. Weeber, and L. Vivien, “Low-Power consumption Franz-Keldysh effect plasmonic modulator,” Opt. Express 22(9), 11236–11243 (2014).DOI
- [11]N. Abadía, S. Olivier, D. Marris-Morini, L. Vivien, T. Bernadin, and J. C. Weeber, “A CMOS-compatible Franz-Keldysh effect plasmonic modulator,” in 2014 11th International Conference on Group IV Photonics (GFP, 2014), pp. 63–64.DOI
- [12]M. A. Foster, A. C. Turner, R. Salem, M. Lipson, and A. L. Gaeta, “Broad-band continuous-wave parametric wavelength conversion in silicon nanowaveguides,” Opt. Express 15(20), 12949–12958 (2007).pubmed.ncbi.nlm.nih.gov/19550563
- [13]Y. Xiong, D. X. Xu, J. H. Schmid, P. Cheben, and W. Y. Ye, “High extinction ratio and broadband silicon TE-pass polarizer using subwavelength grating index engineering,” IEEE Photonics J. 7(5), 7802107 (2015).DOI
- [14]G. V. Naik, V. M. Shalaev, and A. Boltasseva, “Alternative plasmonic materials: Beyond gold and silver,” Adv. Mater. 25(24), 3264–3294 (2013).DOI
- [15]M. Alam, J. S. Aitchison, and M. Mojahedi, “Compact hybrid TM-pass polarizer for silicon-on-insulator platform,” Appl. Opt. 50(15), 2294–2298 (2011).DOI
- [16]Y. Xu and J. Xiao, “A compact TE-pass polarizer for silicon-based slot waveguides,” IEEE Photonics Technol. Lett. 27(19), 2071–2074 (2015).
- [17]Z. Ying, G. Wang, X. Zhang, Y. Huang, H.-P. Ho, and Y. Zhang, “Ultracompact TE-pass polarizer based on a hybrid plasmonic waveguide,” IEEE Photonics Technol. Lett. 27(2), 201–204 (2015).DOI
- [18]X. Guan, P. Chen, S. Chen, P. Xu, Y. Shi, and D. Dai, “Low-loss ultracompact transverse-magnetic-pass polarizer with a silicon subwavelength grating waveguide,” Opt. Lett. 39(15), 4514–4517 (2014).DOI
- [19]X. Sun, M. Z. Alam, S. J. Wagner, J. S. Aitchison, and M. Mojahedi, “Experimental demonstration of a hybrid plasmonic transverse electric pass polarizer for a silicon-on-insulator platform,” Opt. Lett. 37(23), 4814–4816 (2012).DOI
- [20]M. Z. Alam, J. S. Aitchison, and M. Mojahedi, “Compact and silicon-on-insulator-compatible hybrid plasmonic TE-pass polarizer,” Opt. Lett. 37(1), 55–57 (2012).DOI
- [21]X. Guan, P. Xu, Y. Shi, and D. Dai, “Ultra-compact broadband TM-pass polarizer using a silicon hybrid plasmonic waveguide grating,” in Asia Communications and Photonics Conference (2013), pp. 11–13.DOI
- [22]T. Davis, D. Gómez, and A. Roberts, “Plasmonic circuits for manipulating optical information,” Nanophotonics 6, 543–559 (2017).DOI
- [23]T. K. Ng, M. Z. M. Khan, A. Al-Jabr, and B. S. Ooi, “Analysis of CMOS compatible Cu-based TM-pass optical polarizer,” IEEE Photonics Technol. Lett. 24(9), 724–726 (2012).DOI
- [24]S. I. Azzam and S. S. A. Obayya, “Titanium nitride-based CMOS-compatible TE-pass and TM-pass plasmonic polarizers,” IEEE Photonics Technol. Lett. 28(3), 367–370 (2016).DOI
- [25]Y. Xu and J. Xiao, “Design and numerical study of a compact, broadband and low-loss TE-pass polarizer using transparent conducting oxides,” Opt. Express 24(14), 15373–15382 (2016).DOI
- [26]T. Huang, “TE-pass polarizer based on epsilon-near-zero material embedded in a slot waveguide,” IEEE Photonics Technol. Lett. 28(20), 2145–2148 (2016).DOI
- [27]R. F. Oulton, V. J. Sorger, D. A. Genov, D. F. P. Pile, and X. Zhang, “A hybrid plasmonic waveguide for subwavelength confinement and long-range propagation,” Nat. Photonics 2(8), 496–500 (2008).
- [28]M. Fukuda, H. Sakai, T. Mano, Y. Kimura, M. Ota, M. Fukuhara, T. Aihara, Y. Ishii, and T. Ishiyama, “Plasmonic and electronic device integrated circuits and their characteristics,” in 2015 45th European Solid State Device Research Conference (ESSDERC, 2015), pp. 105–108.DOI
- [29]A. Emboras, A. Najjar, S. Nambiar, P. Grosse, E. Augendre, C. Leroux, B. de Salvo, and R. E. de Lamaestre, “MNOS stack for reliable, low optical loss, Cu based CMOS plasmonic devices,” Opt. Express 20(13), 13612–13621 (2012).DOI
- [30]Lumerical Solutions, “Lumerical Solutions, Inc. http://www.lumerical.com,” http://www.lumerical.com.
- [31]S. Maier, Plasmonics: Fundamentals and applications (Springer, 2007).DOI
- [32]M. G. Saber, N. Abadía, and D. V. Plant, “CMOS compatible all-silicon TM pass polarizer based on highly doped silicon waveguide,” Opt. Express 26(16), 20878–20887 (2018).DOI
