betaFeedback

WorksPhysics and Astronomy

Theoretical study and finite element simulation of ZnO/GaAs higher-order Lamb waves for microsensor application in liquid media

Abstract

Lamb waves with dominantly longitudinal displacement component have been reported for sensor application in liquid media. However, they are still limited for the fundamental symmetry mode with low plate thickness-to-wavelength (h/l) ratio, resulting in large wavelength and low resonance frequency. Here we show the finite element simulation study of higher-order Lamb waves on GaAs and ZnO/GaAs plates. In-plane polarised quasi-longitudinal higher-order Lamb waves are obtained at higher h/l ratio resulting in higher resonance frequencies. The solid-liquid contact simulation shows the confinement of acoustic energy inside the plate. The result demonstrates the suitability of ZnO/GaAs higher-order quasi-longitudinal modes for microsensor in liquid media.

Introduction

While the applications of the acoustic waves-based sensors have been reported for several decades [1], the recent trend of bio and chemical sensor integration within a microfluidic and lab-on-chip system has risen a new interest of this research field [2]. One particular interest is on plate acoustic waves (PAW) that offer several advantages, such as faster sound velocity and the two free plate surfaces for the separation between the electrical transducer surface and the sensing surface [3]. The bulk acoustic wave (BAW)-based sensor, such as quartz crystal microbalance (QCM) [4] and lateral field excitation thickness-shear waves (LFE-TSW) [5] offer similar advantages; however, the thickness of the plate dictates the resonance frequency of the devices (plate thickness = half of the wavelength). The wavelength in PAW corresponds to the interdigitated transducers (IDTs) geometry so that the resonance frequency can be increased by scaling down the IDTs.

Shear Horizontal Acoustic Plate Mode (SH-APM) is the most common type of PAW for biosensor application in liquid media [6]. SH-APM has in-plane shear horizontal polarisation resulting in the confinement of acoustic energy inside the plate when the surface of the plate is in contact with liquid media. Lamb wave is another type of PAW [7]. In general, Lamb wave is elliptically polarised with two particle displacement components: longitudinal and shear-vertical. Under specific plate thickness to wavelength (h/λh/\lambda) ratio, Lamb wave has a dominantly in-plane longitudinal component with close to zero shear vertical component. For fundamental symmetry Lamb waves (S0S_0), the h/λh/\lambda ratio is generally less than 0.1; thus the wavelength is ten times larger than the plate thickness. Recently, higher-order Lamb waves with a quasi-longitudinal component in ST-cut Quartz [8] at a higher h/λh/\lambda ratio, resulting in a reduction in wavelength to achieve higher resonance frequency.

Gallium Arsenide (GaAs) is a unique material due to its piezoelectric and optical properties for potential application of acoustic [5] and photonic sensor [9] integrated into the same substrate. GaAs biosensor can be integrated with a microfluidic channel by direct bonding process [10]. However, the piezoelectricity of GaAs is relatively smaller compared to those commonly used piezoelectric materials. Deposition of thinfilm with higher piezoelectricity such as ZnO can increase the electromechanical coupling coefficient K2K^2 of the generated acoustic waves [11].

In this paper, quasi-longitudinal higher-order Lamb waves based on GaAs and ZnO/GaAs will be theoretically studied by finite element simulation. The effect of ZnO deposition to K2K^2 and displacement field profile will be evaluated. Finally, the solid-liquid contact of GaAs/ZnO Lamb waves will be simulated to verify the suitability for sensor application in liquid media.

GaAs Lamb Waves

COMSOL Multiphysics-eigenfrequency studies were used to obtain the dispersion curves of the first six Lamb waves of {100}\{100\}-cut GaAs propagating along the ⟨110⟩\langle110\rangle direction. There are two criteria for the Lamb waves with quasi-longitudinal characteristic: the wave velocity is closed to bulk longitudinal velocity, and the mode is lowly dispersive [8]. Based on those criteria, first and second symmetry higher order modes (QL-S1 and QL-S2) are identified as quasi-longitudinal modes at h/λh/\lambda ratio of 0.6 and 1.2, respectively, as shown in Figure 1.

Lamb wave dispersion curve of {100}-cut GaAs propagating along the <110> direction

Figure 1. Lamb wave dispersion curve of {100}\{100\}-cut GaAs propagating along the ⟨110⟩\langle110\rangle direction.

The plate depth longitudinal (u1u_1) and shear vertical (u3u_3) displacement component profile of the fundamental symmetry Lamb wave QL-S0, QL-S1 and QL-S2 are shown in Figure 2. As shown in Figure 2, all three modes have dominantly u1u_1 component at the surfaces, however, the u3u_3 component for QL-S0 mode is comparatively more significant than QL-S1 and QL-S2. Higher u3u_3 component on the surface of the plate will increase the acoustic energy conversion into pressure wave in the liquid, resulting in higher damping loss. For QL-S1 and QL-S2, u3u_3 components are close to zero so that the acoustic energy loss into the liquid will be minimised.

Figure 2. Displacement depth profile of QL-S0_0, QL-S1_1 and QL-S2_2

The K2K^2 of the three different modes are summarised in table 1 for two different coupling configuration. The deposition of an additional metal layer on the surface opposite of the plate surface with IDTs will result in different electrical boundary condition. The metal-substrate-transducer (MST) and substrate-transducer (ST) are coupling configuration with and without additional metal layer. For simplification, floating electrical boundary conditions are used to represent a massless metal layer in the simulations. However, in the real application, finite thickness metal layer will be used which will give not only an electrical boundary condition but also add to the total thickness of the plate.

ModesGaAs thickness (h)Wavelength (λ\lambda)Ratio h/λ\lambdaOperating FrequencyK2K^2 STK2K^2 MST
QL-S0_030 μ\mum300 μ\mum0.115.8 MHz0.025%0.151%
QL-S1_130 μ\mum50 μ\mum0.6105.5 MHz0.057%0.057%
QL-S2_230 μ\mum25 μ\mum1.2207.8 MHz0.018%0.028%

Table 1. K2K^2 OF GAAS LAMB WAVES

As shown in table 1, the K2K^2 for all three modes with ST configuration are comparable. The K2K^2 of QL-S0_0 mode is six times higher for MST configuration. However, there is no significant increase for QL-S1_1 and QL-S2_2 modes with MST configuration. In [7], thin molybdenum (Mo) metal layer is used as bottom electrode on AlN thin film Lamb waves devices (Mo/AlN/IDT coupling configuration). The result shows improvement in the excitation efficiency of S0_0 Lamb waves. The report is consistent with the improvement in K2K^2 of the simulated MST coupling configuration for the QL-S0_0 mode.

Layered thin film ZnO/GaAs substrate

Hexagonal piezoelectric thin film such as AlN and ZnO has been reported as a promising method to excite acoustic waves on non-piezoelectric material such as silicon [12] and to increase the K2K^2 on material with low piezoelectric constant [13]. In a thin film-substrate layered structure, there are four possible coupling configurations as shown in Figure 3. K2K^2 for four different configurations are calculated for 1 μm1\,\mu\mathrm{m} ZnO thin film deposited on 30 μm30\,\mu\mathrm{m} GaAs, and the results are summarised in Table 2. In general, the deposition of ZnO on GaAs increase the K2K^2 of all modes, except for the STF configuration. An improvement of more than one order in K2K^2 is achieved by the SMFT coupling configuration.

Layered thin film ZnO/GaAs substrate configurations

Figure 3. Layered thin film ZnO/GaAs substrate configurations

ModesOperating FrequencyK2K^2 SFTK2K^2 STFK2K^2 SMFTK2K^2 STFM
QL-S0_015.9 MHz0.038%0.013%0.389%0.364%
QL-S1_1105.8 MHz0.227%0.038%0.607%0.417%
QL-S2_2211.5 MHz0.237%0.009%0.579%0.351%

Table 2. K2K^2 OF ZnO/GaAs LAMB WAVES

While the deposition of ZnO improves the K2K^2, it may also alter the displacement field profile where the u3u_3 displacement component is no longer close to zero on the surface of the plate. Moreover, a non-homogenous ZnO/GaAs will result in unsymmetrical displacement profile. The plate displacement profile of ZnO/GaAs plate is shown in Figure 4. As shown in Figure 4, the u1u_1 component is still dominant for all modes, thus all three modes are still dominantly longitudinal modes even with the addition of ZnO thin film.

Normalised depth $u_1$ and $u_3$ displacement profiles of ZnO/GaAs plate for the SMFT configuration

Figure 4. Normalised depth u1u_1 and u3u_3 displacement profiles of ZnO/GaAs plate for the SMFT configuration. Images are not in scale. All three plates have the same thickness of 31 μm but different wavelength. The width of the plates are equal to one wavelength.

While the three modes are quasi-longitudinal modes, however, it is important to evaluate the effect of ZnO film to the u3u_3 displacement on the plate surfaces. Figure 5 shows the u3u_3 absolute displacement profile normalised to the maximum u1u_1 displacement, with focus on the plate surfaces. As shown in figure 5, the surface displacement profile is no longer symmetrical where the u3u_3 displacement at the GaAs surface is higher than at the ZnO surface for all three modes. The increase in the u3u_3 displacement on one side of the plate is more prominent in for QL-S1_1 and QL-S2_2 modes. However, the displacement is still lower than the QL-S0_0 mode, thus it is expected that QL-S1_1 and QL-S2_2 will have less viscous damping when the plate surface is in contact with liquid.

Absolute $u_3$ displacement on the plate surfaces, normalised to maximum $u_1$ displacement

Figure 5. Absolute u3u_3 displacement on the plate surfaces, normalised to maximum u1u_1 displacement.

Solid-liquid contact

COMSOL eigenfrequency and frequency domain studies were performed to study the acoustic energy loss when the plate is in contact with liquid media. For the ZnO/GaAs plate, the IDTs is located in the ZnO surface, while the opposite GaAs surface will be in contact with media. The simulation result of ZnO/GaAs plate-liquid contact is shown in Figure 5. As shown in figure 6, the acoustic energy is confined in the plate for all modes, however, for the QL-S0_0, there is a significant conversion of acoustic energy into pressure wave in the liquid media.

The propagation and the conversion of Lamb waves into pressure waves on the plate-liquid contact is shown in Figure 7. As shown in Figure 7, the u1u_{1} particle displacement is confined in the plate and the displacement is reduced exponentially at the plate-liquid interface. This interface layer will act as viscous-mass loading when the plate is in contact with liquid. Furthermore, the u3u_{3} displacements are converted into pressure wave in the liquid, resulting in acoustic energy loss. As expected, QL−S0\mathrm{QL}-\mathrm{S}_{0} has higher normalised pressure wave displacement in the liquid due to higher u3u_{3} displacement on the surface of the plate.

Plate-liquid contact eigenfrequency simulation results

Figure 7. Plate-liquid contact eigenfrequency simulation results with a perfectly matched layer (PML) at the bottom of the liquid to represent semi-infinite half-space. The scale bar shows the normalised total displacement. Images are not in scale. All three plates have the same thickness of 31 μm31\,\mu\mathrm{m} but different wavelengths. The difference plate thickness on the images corresponds to the h/λh/\lambda ratio.

Frequency domain simulation results for QL Lamb waves resonator

Figure 9. Frequency domain simulation results for QL Lamb waves resonator

The frequency domain simulation results of a single IDT resonator are shown in Figure 8. As shown in Figure 8, the resonance frequency is lower when the plate is in contact with the liquid due to viscous-mass loading effect as previously shown and explained in Figure 7. Since the QL Lamb waves are not purely in-plane polarised, there are still acoustic energy losses into the liquid due to the u3u_{3} displacement component. The acoustic energy loss can be observed by comparing the absolute admittance-frequency curve with and without liquid contact. As previously shown in Figure 7, while all modes show acoustic energy losses into liquid media, QL-S1 and QL-S2 have minimum losses and the acoustic resonance signals in Figure 8 are distinguishable. Therefore, the study shows that ZnO/GaAs higher order QL-S1 and QL-S2 Lamb waves are feasible for sensing application when one of the plate surfaces is in contact with liquid media.

Propagation and conversion of Lamb waves into pressure wave at the plate-liquid interface

Figure 8. Propagation and conversion of Lamb waves into pressure wave at the plate-liquid interface (xx-axis = 0). The negative and positive xx-axis represent the normalised depth/wavelength of the plate and liquid respectively

Conclusion

The potential application of ZnO/GaAs for microsensor in liquid media is reported in this paper based on higher order quasi-longitudinal Lamb waves. The COMSOL finite element simulation studies were performed to obtain the dispersion curve and the design parameter in term of plate thickness-to-wavelength ratio. The QL-S1 and QL-S2 GaAs Lamb waves are achieved at h/λh/\lambda ratio of 0.6 and 1.2, respectively. Furthermore, thin film ZnO/GaAs plate are studied to increase the K2K^{2}. The improvement of more than one order in K2K^{2} is shown for SMFT coupling configuration. Finally, the plate-liquid simulations are performed to verify the confinement of acoustic energy on the plate and the acoustic energy conversion into the pressure wave in liquid media. The eigenfrequency and frequency domain study show that QL-S1 and QL-S2 Lamb waves of ZnO/GaAs plate are suitable for microsensor application in liquid media.

Acknowledgment

This conference proceeding is part of SmOoC project that has received funding from the European Union’s Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement No. 844135

References

  1. [1]M. Hoummady, A. Campitelli, and W. Wlodarski, “Acoustic wave sensors: design, sensing mechanisms and applications,” Smart materials and structures, vol. 6.6, pp. 647, December 1997.DOI
  2. [2]K. Länge, B. E. Rapp, and M. Rapp, “Surface acoustic wave biosensors: a review,” Analytical and bioanalytical chemistry, vol. 391.5, pp. 1509-1519, 2008.DOI
  3. [3]C, Caliendo, and M. Hamidullah, “Guided acoustic wave sensors for liquid environments,” Journal of Physics D: Applied Physics, vol 52.15, pp. 153001, February 2019.DOI
  4. [4]Y. Montagut, J.V. García, Y. Jiménez, C. March, Á. Montoya, and A. Arnau, “QCM technology in biosensors,” Biosensors-Emerging Materials and Applications, pp.153-178, 2011.DOI
  5. [5]T. Leblois, and V. Lacour, “Thermal and conductivity dependence of GaAs based acoustic biosensors,” IEEE International Ultrasonics Symposium (IUS), IEEE, pp.1-4, 2016.DOI
  6. [6]C. Déjous, M. Savart, D. Rebière, and , J. Pistré, “A shear-horizontal acoustic plate mode (SH-APM) sensor for biological media,” Sensors and Actuators B: Chemical, vol. 27.1-3, pp. 452-456, 1995.
  7. [7]T. Mirea, V. Yantchev, J. Olivares, and E. Iborra, “Influence of liquid properties on the performance of SO - mode Lamb wave sensors II: Experimental validation,” Sensors and Actuators B: Chemical, vol. 229, pp. 331-337, 2016.
  8. [8]V.I. Anisimkin, “Sensing properties of the Anisimkin Jr. acoustic modes in uncoated ST-quartz plates,” IEEE transactions on ultrasonics, ferroelectrics, and frequency control, vol. 60.10, pp. 2204-2207, 2013.DOI
  9. [9]E.Nazemi, S. Aithal, W.M. Hassen, E.H. Frost, and J.J. Dubowski, “GaAs/AlGaAs heterostructure based photonic biosensor for rapid detection of Escherichia coli in phosphate buffered saline solution,” Sensors and Actuators B: Chemical, vol.207, pp.556-562, 2015.DOI
  10. [10]C.L. Azzopardi, V. Lacour, J. F. Manceau, M. Barthès, D. Bonnet, F. Chollet, , and T. Leblois, “A fluidic interface with high flow uniformity for reusable large area resonant biosensors,” Micromachines vol. 8.10 pp. 308, 2017.DOI
  11. [11]J. Chawich, S. Kuprenaite, S. Margueron, P. Boulet, J.J. Dubowski, C. Elie-Caille, and T. Leblois, “Deposition and characterization of ZnO thin films on GaAs and Pt/GaAs substrates,” Materials Chemistry and Physics, pp. 122854, 2020.DOI
  12. [12]T. Laurent, F.O. Bastien, J.C. Pommier, A. Remiens, E. Cattan, “Lamb wave and plate mode in ZnO/silicon and AlN/silicon membrane: Application to sensors able to operate in contact with liquid,” Sensors and Actuators A: Physical, vol. 87.1-2, pp. 26-37, 2000.
  13. [13]J. Pedrós, L. Garcia-Gancedo, C. J. B. Ford, C. H. W. Barnes, J. P. Griffiths, G. A. C. Jones, and A. J. Flewitt, “Guided propagation of surface acoustic waves and piezoelectric field enhancement in ZnO/GaAs systems,” Journal of Applied Physics, vol. 110.10, pp. 103501, 2011.DOI

Paper details

vlnc:W_m3gkfrma
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents