betaFeedback

WorksPhysics and Astronomy

Telecom-wavelength InAs QDs with low fine structure splitting grown by droplet epitaxy on GaAs(111)A vicinal substrates

Abstract

We present self-assembly of InAs/InAlAs quantum dots by droplet epitaxy technique on vicinal GaAs(111)A substrates. The small miscut angle, while maintaining the symmetries imposed to the quantum dot from the surface, allows fast growth rate thanks to the presence of preferential nucleation sites at the step edges. A 100 nm InAlAs metamorphic layer with In content > 50% is already almost fully relaxed with a very flat surface. The quantum dots emit at the 1.3 μm telecom O-band with the fine structure splitting as low as 16 μeV, thus making them suitable as photon sources in quantum communication networks using entangled photons.

Introduction

Entangled photon emitters are fundamental components of the future quantum communication network and the basis of the photonic implementation of quantum information protocols [1, 2].

Among possible entangled photon sources, self-assembled quantum dots (QDs) of compound semiconductors are considered as ideal, being able to generate polarization entangled photon pairs on demand via the biexciton (XX)–exciton (X) cascade [1, 2, 3, 4, 5]. The presence of the fine structure splitting (FSS) [6, 7] of the X state, due to QD anisotropy (shape, composition, etc.), generates a decoherence mechanism, which complicates the observation of the entanglement. Highly symmetric QDs with natural low FSS can be achieved by self-assembled growth on (111) surfaces with C3vC_{3v} symmetry [5, 8, 9, 10].

The growth of QDs on (111)-oriented surfaces is not straightforward. The common Stranski–Krastanov (SK) growth mode seen in the InAs/GaAs system [11] is not able to induce the self-assembly of QDs on (111) surfaces because of the rapid relaxation of compressive strain due to the low threshold energy for the insertion of misfit dislocations at the substrate-epilayer interface [12, 13]. However, by switching the strain from compressive to tensile in the epilayers, self-assembled SK GaAs QDs on InAl(Ga)As(111)A were demonstrated [14, 15, 16].

A more efficient and reliable method of obtaining self-assembled QDs on (111) substrates is Droplet Epitaxy (DE) [5, 9, 10, 17, 18]. DE relies on kinetically controlled crystallization, via annealing in a group-V atmosphere, of previously formed nanodroplets of group-III metals [19, 20]. As DE does not rely on an onset of three-dimensional (3D) growth induced by strain, it is possible to obtain QD self-assembly also in strain-free (e.g., GaAs/AlGaAs) or reduced strain conditions (e.g., InAs/InP). By DE, it is possible to create InAs QDs on GaAs(111)A [21] and InP(111)A [22] substrates, which emit photons at the telecom band for conventional fiber communication. QDs have previously been grown on an InAlAs metamorphic buffer layer (MMBL) on singular GaAs(111)A substrates, using a thin InAs interlayer for complete strain relaxation [21]. The photoluminescence (PL) signals of the QDs indicated a broadband spectrum covering wavelengths from 1.3 to 1.55 μ\mum. The main drawback is the very slow growth rate (below 0.1 ML/s) on singular GaAs(111)A [23].

In our work, we present the DE process on GaAs(111)A for InAs QD emission in the 1.3 μ\mum telecom O-band with an FSS as low as 16 μ\mueV. In order to overcome complications related to the low growth rate on singular (111)A surfaces, we employed a vicinal (111)A surface, where the growth rate is one order of magnitude higher and, thus, is similar to that on GaAs(001) [16, 24]. A vicinal surface allows a very flat and almost fully relaxed thin InAlAs MMBL to be obtained, with the root mean square (RMS) roughness of about 1 ML, directly on the GaAs substrate. The measured threading dislocation density (TDD) is of the order of 1×1071 \times10^{7} cm−2^{-2}. The TDD was determined using the etch pit density (EPD) approach [25]. This will allow the integration of the self-assembled InAs/InAl(Ga)As QDs into photonic cavity structures (Bragg reflectors) directly on vicinal GaAs(111)A substrates for high brightness efficient entangled photon emitters.

Experimental Methods

The samples for μ\mu-PL measurements were grown on undoped semi-insulating GaAs(111)A substrates with a miscut of 2° toward (11ˉ2)(1\bar{1}2) in a solid source MBE machine. After a 100 nm GaAs buffer layer grown at 520 °C with a growth rate of 0.5 ML/s, a 200 nm In0.6Al0.4As\mathrm{In}_{0.6}\mathrm{Al}_{0.4}\mathrm{As} barrier layer was deposited at 470 °C with the growth rate of 0.7 ML/s. Then, we supplied indium with the growth rate of 0.01 ML/s at 370 °C, in order to obtain In droplets with a density of about 1×1081 \times10^{8} cm−2^{-2} on InAlAs(111)A. During the indium deposition, the background pressure was below 3×10−93 \times10^{-9} Torr. Then, an As4_4 flux was supplied for 8 min at the same temperature to crystallize the indium droplets into InAs QDs. After the crystallization process, 10 nm and 140 nm In0.6Al0.4As\mathrm{In}_{0.6}\mathrm{Al}_{0.4}\mathrm{As} capping layers were deposited at 370 °C and 470 °C, respectively, with the growth rate of 0.70.7 ML/s. The layer structures and growth parameters of the samples are presented in Table I. The morphological characterization of the samples was performed ex situ by atomic force microscopy (AFM) in tapping mode, using tips capable of a lateral resolution of about 2 nm.

SampleMMBLIn depositionAnnealing in As atmosphereCapping Layer
AIn0.52Al0.48As\mathrm{In}_{0.52}\mathrm{Al}_{0.48}\mathrm{As}, 470 °C, 100nm–––
BIn0.52Al0.48As\mathrm{In}_{0.52}\mathrm{Al}_{0.48}\mathrm{As}, 470 °C, 100nm––
CIn0.6Al0.4As\mathrm{In}_{0.6}\mathrm{Al}_{0.4}\mathrm{As}, 470 °C, 100nm–––
DIn0.6Al0.4As\mathrm{In}_{0.6}\mathrm{Al}_{0.4}\mathrm{As}, 470 °C, 200nm370 °C, 1 ML370 °C, 5×10−55 \times10^{-5} torr–
EIn0.6Al0.4As\mathrm{In}_{0.6}\mathrm{Al}_{0.4}\mathrm{As}, 470 °C, 200nm370 °C, 2 ML370 °C, 5×10−55 \times10^{-5} torr–
FIn0.6Al0.4As\mathrm{In}_{0.6}\mathrm{Al}_{0.4}\mathrm{As}, 470 °C, 200nm370 °C, 1 ML370 °C, 5×10−55 \times10^{-5} torrIn0.6Al0.4As\mathrm{In}_{0.6}\mathrm{Al}_{0.4}\mathrm{As}, 10 and 140 nm at 370 and 470 °C
GIn0.6Al0.4As\mathrm{In}_{0.6}\mathrm{Al}_{0.4}\mathrm{As}, 470 °C, 200nm370 °C, 2 ML370 °C, 5×10−55 \times10^{-5} torrIn0.6Al0.4As\mathrm{In}_{0.6}\mathrm{Al}_{0.4}\mathrm{As}, 10 and 140 nm at 370 and 470 °C

Table I. Layer structure and growth parameters of the samples presented in this work.

A PANalytical X’Pert PRO MRD high resolution X-ray diffractometer (HR-XRD) equipped with a hybrid mirror and a 2-bounce Ge(220) monochromator was employed for HR-XRD measurements.

To perform PL measurements, the samples were placed in a closed-cycle cryostat and cooled to 8–10 K. To excite the samples, we used a continuous-wave (cw) HeNe laser (632.8 nm). The laser light was focused on the sample using a microscope objective lens with a numerical aperture of 0.8. The spot diameter was of the order of 1 μm. The luminescence signal was collected by the same objective and passed through a beam splitter (10% transmission and 90% reflection) to a spectrometer that contains an 830 line/mm grating. The luminescence signal was spectrally analyzed using a cooled InGaAs photodiode array. A half-wave plate (HWP) and a linear polarizer were inserted into the optical path before the spectrometer, in order to perform polarization-dependent PL measurements.

Results and Discussion

In order for QDs to emit at telecom wavelengths, it is necessary to use direct-bandgap semiconductor materials with the bandgap below 0.8 eV. One of the III–V semiconductors that may satisfy such a requirement is InAs with its bandgap of 0.35 eV at 300 K and about 0.42 eV at the temperature of liquid He. Unfortunately, InAs QDs embedded in a GaAs matrix emit at a wavelength of about 1 μm\mu\mathrm{m} [11, 26, 27] due to the lattice mismatch between GaAs and InAs (about 7%, which affects the maximum size of coherent islands). Therefore, to shift the emission to longer wavelengths and to improve the crystal quality, it is necessary to adapt the heterostructure composition. One possible approach is to fabricate InAs QDs embedded in InGa(Al)As layers, metamorphically grown on GaAs substrates, to reduce the strain between QD and barrier layer materials [28]. This approach was successfully used to shift the InAs QD emission to the telecom band (1.31–1.55 μm\mu\mathrm{m}) [21, 28, 29, 30].

Metamorphic substrate optimization on vicinal GaAs(111)A

The realization of an InAl(Ga)As MMBL with the In composition higher than 50% and with a high crystalline quality and a flat surface on a GaAs(111)A substrate is made more difficult by the actual atomic configuration of the surface and by the presence of steps induced by the substrate miscut.

To obtain a fully relaxed InAl(Ga)As MMBL on a singular GaAs(111)A substrate, Mano et al. [21, 25] inserted a thin InAs interlayer between the substrate and the MMBL. This has been observed to induce drastic relaxation, due to the introduction of misfit dislocations at the InAs/GaAs interface during the growth of the thin InAs layer [31, 32]. It was found that the optimal thickness of the InAs interlayer is 3–7 ML; otherwise, the crystal quality and/or the surface morphology of the InAl(Ga)As MMBL worsen. As a result, a near strain-free metamorphic InAl(Ga)As layer can be formed on singular GaAs(111)A [21, 25]. The samples we grew on miscut GaAs(111)A substrates with the insertion of a thin InAs interlayer between the substrate and the InAlAs MMBL did indeed demonstrate full relaxation of the InAlAs MMBL, as in the case of singular GaAs(111)A substrates. However, we also observed the appearance of large islands, with an average lateral size and height of 602±\pm69 and 17.8±\pm4.9 nm, respectively, and with a density of about 7×106 cm−27 \times10^{6}\,\mathrm{cm}^{-2}. Such islands can become nucleation sites for droplets and non-radiative recombination centers during the subsequent growth of the QD active layer. We have found, instead, that on vicinal GaAs(111)A substrates, a fully relaxed InAlAs MMBL, showing a flat surface (RMS roughness < 0.5 nm) and free of large islands, can be obtained by the direct growth of a thin layer (100 nm thickness) with the desired composition. Figure 1(a) displays an XRD reciprocal space map (RSM) for the (224) asymmetric Bragg reflection of sample A. It shows two diffraction peaks that originate from GaAs and In0.52Al0.48As\mathrm{In}_{0.52}\mathrm{Al}_{0.48}\mathrm{As}. The position of the peak suggests that the indium content in the InAlAs layer is 52.0±0.4%52.0 \pm0.4\%. The peak position of In0.52Al0.48As\mathrm{In}_{0.52}\mathrm{Al}_{0.48}\mathrm{As} on the XRD RSM of sample B is the same as that of sample A.

XRD reciprocal space map and AFM amplitude image

Figure 1. (a) XRD reciprocal space map, taken near the (224) asymmetric Bragg reflection of sample A. (b) 10×10 μm210 \times10\ \mu\mathrm{m}^{2} AFM amplitude image of sample C (the inset shows 1×1 μm21 \times1\ \mu\mathrm{m}^{2} AFM tapping amplitude image of the sample).

To find the InAlAs barrier layer content for InAs QD emission at the telecom band, we perform a quantum mechanical 8-band k.pk.p model calculation. The InAs QD has been modeled as a truncated pyramid with a regular triangular base and a small aspect ratio (height to width ratio). As presented below, the actual aspect ratio of our InAs QDs is about 0.05. The InAs QD is surrounded by strain relaxed InAlAs. The simulation suggests using an Al content in the InAlAs layer of less than 50% and a height of the QD of more than 4 nm. Thus, an In0.6Al0.4As\mathrm{In}_{0.6}\mathrm{Al}_{0.4}\mathrm{As} barrier layer was chosen for subsequent QD growth. Additionally, the growth of an InAlAs layer with such an In content significantly reduces the strain between the barrier layer and the InAs QDs, which decreases the number of misfit dislocations at the InAs/InAlAs interface improving the optical properties of the QDs. Figure 1(b) shows an AFM image of sample C with 100 nm In0.6Al0.4As\mathrm{In}_{0.6}\mathrm{Al}_{0.4}\mathrm{As} directly grown on vicinal GaAs(111)A. The RMS roughness of the surface is observed to be 0.43 nm, calculated from a 1×1 μm21 \times1\ \mu\mathrm{m}^{2} AFM scan, which is comparable to the 1.3 ML thickness of In0.6Al0.4As\mathrm{In}_{0.6}\mathrm{Al}_{0.4}\mathrm{As} along [111]. The RMS roughness of sample C, calculated from 5×55 \times5 and 10×10 μm210 \times10\ \mu\mathrm{m}^{2} AFM scans, is about 1 nm. Etch pit counting reveals that the TDD is of the order of 1×107 cm−21 \times10^{7}\ \mathrm{cm}^{-2}.

Droplet epitaxy quantum dots self-assembly

In order to study individual QDs by μ\mu-PL, it is necessary to create nanostructures with a density of 10810^{8}–109 cm−210^{9}\,\mathrm{cm}^{-2}. From previous work [33], we have determined that In droplets, directly deposited on a vicinal GaAs(111)A substrate at a temperature of about 400 °C, have the desired density.

Figure 2 shows the morphology of samples D and E with uncapped self-assembled DE InAs QDs fabricated on a 200 nm In0.6_{0.6}Al0.4_{0.4}As MMBL by deposition of 1 and 2 ML of indium at 370 °C, respectively, followed by annealing in an As4_4 atmosphere at the same temperature. QD densities for both samples are almost the same: 2.52×108 cm−22.52\times10^{8}\,\mathrm{cm}^{-2} for sample D and 2.50×108 cm−22.50\times10^{8}\,\mathrm{cm}^{-2} for sample E, calculated from 10×10 μm210\times10\ \mu\mathrm{m}^{2} AFM scan of each sample. It is worth mentioning that the shape of the QDs is different between samples. Most of the QDs of sample D have a triangular pyramidal shape [see the inset of Figure 2(a)] with a height of 9.6±2.39.6\pm2.3 nm and a width of 196±41196\pm41 nm, measured for 50 QDs. On the other hand, the majority of QDs of sample E have hexagonal-like pyramidal shapes [see the inset of Figure 2(b)] with a height of 15.9±3.315.9\pm3.3 nm and a width of 266±52266\pm52 nm, measured also for 50 QDs. According to Ref. 34, the GaAs DE-QD formation process is strongly affected by the diffusion of Ga adatoms out of the droplet, which leads to the accumulation of GaAs material within a Ga diffusion length of the droplet edge. Using identical crystallization conditions (substrate temperature and As flux), the Ga adatom diffusion length is the same. Considering a model of triangular and hexagonal DE GaAs QD formation on GaAs(111)A [18, 35], with the increasing initial droplet size, a shape transition from triangular to hexagonal should occur.

AFM tapping amplitude images of samples D and E with insets showing individual quantum dots

Figure 2. (a) 5×5 μm25\times5\ \mu\mathrm{m}^{2} AFM tapping amplitude image of sample D (the inset shows 1×1 μm21\times1\ \mu\mathrm{m}^{2} AFM tapping amplitude image of an individual QD with triangular pyramidal shape); (b) 5×5 μm25\times5\ \mu\mathrm{m}^{2} AFM tapping amplitude image of sample E (the inset shows 1×1 μm21\times1\ \mu\mathrm{m}^{2} AFM tapping amplitude image of an individual QD with asymmetrical hexagonal-like pyramidal shape).

Furthermore, the hexagonal QDs of sample E are elongated in the [11‾0]\left[1\overline{1}0\right] direction along steps due to the presence of a sizeable Ehrlich-Schwöbel (ES) [17], which hinders an adatom diffusivity in the [1‾12]\left[\overline{1}12\right] direction perpendicular to the steps.

Single InAs/InAlAs quantum dot emission

Samples F and G with capped InAs QDs were characterized by μ\mu-PL. Figure 3(a) shows the broadband PL spectrum of sample F in the range of 800–1500 nm. The peak at 838 nm corresponds to the GaAs substrate, the peaks in the range of 900–1110 nm are associated with defects in the In0.6Al0.4As\mathrm{In}_{0.6}\mathrm{Al}_{0.4}\mathrm{As} MMBL (the bandgap of that layer is about 1.32 eV, which corresponds to 940 nm), and the emissions from InAs QDs are placed in the 1100–1350 nm broadband. The broadband PL spectrum of sample G is extremely similar to that of sample F.

Broadband PL spectrum of sample F and luminescence spectrum of an individual InAs dot for sample F

Figure 3. (a) The broadband PL spectrum of sample F with a cw excitation of 10 μ\muW; (b) The luminescence spectrum of an individual InAs dot for sample F with a cw excitation of 0.6 μ\muW. The inset shows power dependence of PL intensity of the observed neutral X line.

A typical PL spectrum of an individual QD of sample F is presented in Figure 3(b). The observed peak with a linewidth (FWHM) of about 250 μ\mueV (0.33 nm), fitted by a Gaussian function, is attributed to the neutral X line, due to the linear dependence of PL intensity on the excitation power together with the splitting of the emission line into two components, which are linearly polarized in perpendicular directions [36, 37]. The observed FWHM of QDs for both samples is in the range of 150—350 μ\mueV. The resolution of the PL setup is 0.07 nm, which corresponds to about 50 μ\mueV at 1310 nm.

Polarization-dependent PL measurements were performed for both samples (see Figure 4). FSS measurements below the limit of the spectrometer were achieved by a polarization sensitive detection method [38, 39], which makes it possible to measure FSS with a limit of about 1 μ\mueV using this setup [29]. Figure 4(a) shows a polarization angle dependence of the emission line. energy extracted from the center-of-mass PL intensity for an individual QD of sample G, emitting at 1310 nm. The measurement reveals an FSS of 55±4 μeV55\pm4\,\mu\mathrm{eV} for this QD.

Polarization dependence and statistical distribution of fine-structure splitting

Figure 4. (a) Polarization dependence of QD emission line (1310 nm) of sample G with a finite FSS = 55±4 μeV55\pm4\,\mu\mathrm{eV}. (b) Statistical distribution of FSS of samples F (green points) and G (red points).

The most important feature is the existence of telecom QDs with the FSS less than 20 μeV\mu\mathrm{eV} in 20% of the cases [highlighted by a red rectangle in Figure 4(b)]. The FSS of QDs of sample F ranges from 15 to 100 μeV\mu\mathrm{eV}, with 80% of investigated QDs having the FSS below 60 μeV\mu\mathrm{eV}. As expected, the bigger QDs found on sample G emit at longer wavelengths. Poor statistics for the sample are associated with the fact that most of the observed peaks are related to charged excitons, which do not show FSS, so that just a few neutral lines were observed. The FSS of QDs of sample G is within the range of 55–120 μeV\mu\mathrm{eV}, which is larger than that of the majority of sample F. The larger values of the FSS in sample G in the wavelength region of interest are tentatively associated with the asymmetrical shape of the QDs even if other effects such as the size and strain may play a relevant role.

Conclusions

In conclusion, we have demonstrated DE growth of InAs QDs embedded in InAlAs layers on vicinal GaAs(111)A substrates, with the high growth rate of a standard (001) substrate process and the high shape symmetry of (111) QDs. A very flat and smooth MMBL with an RMS roughness of about 1 ML has been obtained by direct growth of a 100 nm InAlAs thin layer on GaAs. XRD measurements show that this layer is fully relaxed. The possibility to obtain an MMBL of high quality by using thin epitaxial layers opens the prospect of integrating such structures in cavities realized by distributed Bragg reflectors. In order to perform 1-PL characterization of individual QDs, InAs QDs were obtained at a low density of about 2.5×108 cm−22.5\times10^{8}\,\mathrm{cm}^{-2}. Two types of QD shapes (symmetrical triangular pyramids and hexagonal-like pyramids elongated in the [11ˉ0]\left[1\bar{1}0\right]) were observed, depending on the initial size of the droplets.

Fine structure splittings as low as 16±616 \pm6 μeV at the 1.31.3 μm telecom O-band suggest the possibility to use these QDs for the future fabrication of entangled photon emitters. The FSS of these dots is similar to that for DE InAs/InP(001) QDs grown by metalorganic vapor phase epitaxy (MOVPE) [40] and slightly higher those of the SK InAs QDs grown on InGaAs/GaAs(001) also by MOVPE [29, 30]. To be able to adopt this growth technique for routine use in telecom applications, the samples can be further improved as follows. A rather broad PL linewidth is observed (the mean linewidth is about 250250 μeV). We attribute such a behavior to the presence of point defects, due to the low deposition temperature for Al during InAlAs layer growth, the presence of threading dislocations in the InAlAs MMBL, and twin defects after the capping of the InAs QDs. Since InAlAs layers, grown at temperatures above 450450 °C, tend to show step bunching with a high number of steps, it is possible to change the MMBL composition from InAlAs to InGaAs. In order to increase the brightness of the dots, InAs QDs could be placed in an InAl(Ga)As cavity between GaAs/Al(Ga)As Bragg reflectors, which can easily be grown on vicinal GaAs(111)A substrates.

Data Availability

The data that support the findings of this study are available from the corresponding author upon reasonable request.

Acknowledgments

The research was supported by the funding from the European Union’s Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement № 721394.

This article may be downloaded for personal use only. Any other use requires prior permission of the author and AIP Publishing. This article appeared in Applied Physics Letters 118, 133102 (2021) and may be found at https://aip.scitation.org/doi/10.1063/5.0045776.

References

  1. [1]A. Orieux, M. A. M. Versteegh, K. D. Jöns, and S. Ducci, “Semiconductor devices for entangled photon pair generation: a review,” Rep. Prog. Phys. 80, 076001 (2017).DOI
  2. [2]D. Huber, M. Reindl, J. Aberl, A. Rastelli, and R. Trotta, “Semiconductor quantum dots as an ideal source of polarization-entangled photon pairs on-demand: a review,” J. Opt. 20, 073002 (2018).DOI
  3. [3]J. Skiba-Szymanska, R. M. Stevenson, C. Varnava, M. Felle, J. Huwer, T. Müller, A. J. Bennett, J. P. Lee, I. Farrer, A. B. Krysa, P. Spencer, L. E. Goff, D. Ritchie, J. Heffernan, and A. J. Shields, “Universal growth scheme for quantum dots with low fine-structure splitting at various emission wavelengths,” Phys. Rev. Appl. 8, 014013 (2017).
  4. [4]D. Huber, M. Reindl, S. F. C. da Silva, C. Schimpf, J. Martin-Sanchez, H. Huang, G. Piredda, J. Edlinger, A. Rastelli, and R. Trotta, “Strain-tunable GaAs quantum dot: A nearly dephasing-free source of entangled photon pairs on demand,” Phys. Rev. Lett. 121, 033902 (2018).DOI
  5. [5]F. Basso Basset, S. Bietti, M. Reindl, L. Esposito, A. Fedorov, D. Huber, A. Rastelli, E. Bonera, R. Trotta, and S. Sanguinetti, “High-yield fabrication of entangled photon emitters for hybrid quantum networking using high-temperature droplet epitaxy,” Nano Lett. 18, 505–512 (2018).DOI
  6. [6]D. Gammon, E. S. Snow, B. V. Shanabrook, D. S. Katzer, and D. Park, “Fine structure splitting in the optical spectra of single GaAs quantum dots,” Phys. Rev. Lett. 76, 3005–3008 (1996).pubmed.ncbi.nlm.nih.gov/10060846
  7. [7]M. Bayer, G. Ortner, O. Stern, A. Kuther, A. A. Gorbunovand, A. Forchel, P. Hawrylak, S. Fafard, K. Hinzer, T. L. Reinecke, S. N. Walck, J. P. Reithmaier, F. Klopf, and F. Schafer, “Fine structure of neutral and charged excitons in self-assembled In(Ga)As/(Al)GaAs quantum dots,” Phys. Rev. B 65, 195315 (2002).DOI
  8. [8]R. Singh and G. Bester, “Nanowire quantum dots as an ideal source of entangled photon pairs,” Phys. Rev. Lett. 103, 063601 (2009).pubmed.ncbi.nlm.nih.gov/19792564
  9. [9]T. Mano, M. Abbarchi, T. Kuroda, B. McSkimming, A. Ohtake, K. Mitsuishi, and K. Sakoda, “Self-assembly of symmetric GaAs quantum dots on (111)A substrates: Suppression of fine-structure splitting,” Appl. Phys. Express 3, 065203 (2010).DOI
  10. [10]T. Kuroda, T. Mano, N. Ha, H. Nakajima, H. Kumano, B. Urbaszek, M. Jo, M. Abbarchi, Y. Sakuma, K. Sakoda, I. Suemune, X. Marie, and T. Amand, “Symmetric quantum dots as efficient sources of highly entangled photons: Violation of Bell’s inequality without spectral and temporal filtering,” Phys. Rev. B 88, 041306(R) (2013).DOI
  11. [11]J. X. Chen, A. Markus, A. Fiore, U. Oesterle, R. P. Stanley, J. F. Carlin, R. Houdre, M. Ilegems, L. Lazzarini, L. Nasi, M. T. Todaro, E. Piscopello, R. Cingolani, M. Catalano, J. Katcki, and J. Ratajczak, “Tuning InAs/GaAs quantum dot properties under Stranski-Krastanov growth mode for 1.3 μm applications,” J. Appl. Phys. 91, 6710–6716 (2002).DOI
  12. [12]H. Yamaguchi, J. G. Belk, X. M. Zhang, J. L. Sudijono, M. R. Fahy, T. S. Jones, D. W. Pashley, and B. A. Joyce, “Atomic-scale imaging of strain relaxation via misfit dislocations in highly mismatched semiconductor heteroepitaxy: InAs/GaAs(111)A,” Phys. Rev. B 55, 1337–1340 (1997).DOI
  13. [13]H. Wen, Z. M. Wang, J. L. Shultz, B. L. Liang, and G. J. Salamo, “Growth and characterization of InAs epitaxial layer on GaAs(111)B,” Phys. Rev. B 70, 205307 (2004).DOI
  14. [14]C. D. Yerino, P. J. Simmonds, B. Liang, D. Jung, C. Schneider, S. Unsleber, M. Vo, D. L. Huffaker, S. Hofling, M. Kamp, and M. L. Lee, “Strain-driven growth of GaAs(111) quantum dots with low fine structure splitting,” Appl. Phys. Lett. 105, 251901 (2014).DOI
  15. [15]C. F. Schuck, R. A. McCown, A. Hush, A. Mello, S. Roy, J. W. Spinuzzi, B. Liang, D. L. Huffaker, and P. J. Simmonds, “Self-assembly of (111)-oriented tensile-strained quantum dots by molecular beam epitaxy,” J. Vac. Sci. Technol. B 36, 031803 (2018).DOI
  16. [16]C. F. Schuck, S. K. Roy, T. Garrett, Q. Yuan, Y. Wang, C. I. Cabrera, K. A. Grossklaus, T. E. Vandervelde, B. Liang, and P. J. Simmonds, “Anomalous Stranski-Krastanov growth of (111)-oriented quantum dots with tunable wetting layer thickness,” Sci. Rep. 9, 18179 (2019).DOI
  17. [17]A. Tuktamyshev, A. Fedorov, S. Bietti, S. Tsukamoto, and S. Sanguinetti, “Temperature activated dimensionality crossover in the nucleation of quantum dots by droplet epitaxy on GaAs(111)A vicinal substrates,” Sci. Rep. 9, 14520 (2019).DOI
  18. [18]S. Bietti, F. Basso Basset, A. Tuktamyshev, E. Bonera, A. Fedorov, and S. Sanguinetti, “High–temperature droplet epitaxy of symmetric GaAs/AlGaAs quantum dots,” Sci. Rep. 10, 6532 (2020).DOI
  19. [19]S. Sanguinetti, S. Bietti, and N. Koguchi, “Droplet epitaxy of nanostructures,” in Molecular Beam Epitaxy: From Research to Mass Production, 2nd ed. (Elsevier, 2018), Chap. 13, pp. 293–314.
  20. [20]M. Gurioli, Z. Wang, A. Rastelli, T. Kuroda, and S. Sanguinetti, “Droplet epitaxy of semiconductor nanostructures for quantum photonic devices,” Nat. Mater. 18, 799–810 (2019).DOI
  21. [21]N. Ha, T. Mano, T. Kuroda, K. Mitsuishi, A. Ohtake, A. Castellano, S. Sanguinetti, T. Noda, Y. Sakuma, and K. Sakoda, “Droplet epitaxy growth of telecom InAs quantum dots on metamorphic InAlAs/GaAs(111)A,” Jpn. J. Appl. Phys. 54, 04DH07 (2015).DOI
  22. [22]N. Ha, T. Mano, S. Dubos, T. Kuroda, Y. Sakuma, and K. Sakoda, “Single photon emission from droplet epitaxial quantum dots in the standard telecom window around a wavelength of 1.55 μm,” Appl. Phys. Express 13, 025002 (2020).
  23. [23]L. Esposito, S. Bietti, A. Fedorov, R. Notzel, and S. Sanguinetti, “Ehrlich–Schwobel effect on the growth dynamics of GaAs(111)A surfaces,” Phys. Rev. Mater. 1, 024602 (2017).DOI
  24. [24]F. Herzog, M. Bichler, G. Koblmuller, S. Prabhu-Gaunkar, W. Zhou, and M. Grayson, “Optimization of AlAs/AlGaAs quantum well heterostructures on on-axis and misoriented GaAs(111)B,” Appl. Phys. Lett. 100, 192106 (2012).
  25. [25]T. Mano, K. Mitsuishi, N. Ha, A. Ohtake, A. Castellano, S. Sanguinetti, T. Noda, Y. Sakuma, T. Kuroda, and K. Sakoda, “Growth of metamorphic InGaAs on GaAs(111)A: Counteracting lattice mismatch by inserting a thin InAs interlayer,” Cryst. Growth Des. 16, 5412–5417 (2016).DOI
  26. [26]W.-H. Chang, W. Y. Chen, T. M. Hsu, N.-T. Yeh, and J.-I. Chyi, “Hole emission processes in InAs/GaAs self-assembled quantum dots,” Phys. Rev. B 66, 195337 (2002).DOI
  27. [27]M. Souaf, M. Baira, O. Nasr, M. H. H. Alouane, H. Maaref, L. Sfaxi, and B. Ilahi, “Investigation of the InAs/GaAs quantum dots’ size: Dependence on the strain reducing layer’s position,” Materials 8, 4699–4709 (2015).DOI
  28. [28]L. Seravalli, M. Minelli, P. Frigeri, S. Franchi, G. Guizzetti, M. Patrini, T. Ciabattoni, and M. Geddo, “Quantum dot strain engineering of InAs/InGaAs nanostructures,” J. Appl. Phys. 101, 024313 (2007).DOI
  29. [29]M. Paul, F. Olbrich, J. Hœschele, S. Schreier, J. Kettler, S. Portalupi, M. Jetter, and P. Michler, “Single-photon emission at 1.55 μm from MOVPE-grown InAs quantum dots on InGaAs/GaAs metamorphic buffers,” Appl. Phys. Lett. 111, 033102 (2017).DOI
  30. [30]K. D. Zeuner, K. D. Jons, L. Schweickert, C. R. Hedlund, C. Nu¬nez-Lobato, T. Lettner, K. Wang, S. Gyger, E. Schöll, S. Steinhauer, M. Hammar, and V. Zwiller, “On-demand generation of entangled photon pairs in the telecom C–band for fiber–based quantum networks,” arXiv:1912.04782v1 (2019).arxiv.org/abs/1912.04782
  31. [31]A. Ohtake, M. Ozeki, and J. Nakamura, “Strain relaxation in InAs/GaAs(111)A heteroepitaxy,” Phys. Rev. Lett. 84, 4665–4668 (2000).pubmed.ncbi.nlm.nih.gov/10990766
  32. [32]A. Ohtake, T. Mano, and Y. Sakuma, “Strain relaxation in InAs heteroepitaxy on lattice-mismatched substrates,” Sci. Rep. 10, 4606 (2020).DOI
  33. [33]A. Tuktamyshev, A. Fedorov, S. Bietti, S. Tsukamoto, R. Bergamaschini, F. Montalenti, and S. Sanguinetti, “Reentrant behavior of the density vs. temperature of indium islands on GaAs(111)A,” Nanomaterials 10, 1512 (2020).DOI
  34. [35]M. Jo, T. Mano, M. Abbarchi, T. Kuroda, Y. Sakuma, and K. Sakoda, “Self-limiting growth of hexagonal and triangular quantum dots on (111)A,” Cryst. Growth Des. 12, 1411–1415 (2012).DOI
  35. [36]S. Kako, C. Santori, K. Hoshino, S. Gozinger, Y. Yamamoto, and Y. Arakawa, “A gallium nitride single-photon source operating at 200 K,” Nat. Mater. 5, 887–892 (2006).pubmed.ncbi.nlm.nih.gov/17057699
  36. [37]M. Abbarchi, C. Mastrandrea, T. Kuroda, T. Mano, A. Vinattieri, K. Sakoda, and M. Gurioli, “Poissonian statistics of excitonic complexes in quantum dots,” J. Appl. Phys. 106, 053504 (2009).DOI
  37. [38]K. Kowalik, O. Krebs, A. Lemaître, S. Laurent, P. Senellart, P. Voisin, and J. A. Gaj, “Influence of an in-plane electric field on exciton fine structure in InAs-GaAs self-assembled quantum dots,” Appl. Phys. Lett. 86, 041907 (2005).
  38. [39]R. Trotta, E. Zallo, C. Ortix, P. Atkinson, J. D. Plumhof, J. van den Brink, A. Rastelli, and O. G. Schmidt, “Universal recovery of the energy-level degeneracy of bright excitons in InGaAs quantum dots without a structure symmetry,” Phys. Rev. Lett. 109, 147401 (2012).pubmed.ncbi.nlm.nih.gov/23083282
  39. [40]T. Muller, J. Skiba-Szymanska, A. B. Krysa, J. Huwer, M. Felle, M. Anderson, R. M. Stevenson, J. Heffernan, D. A. Ritchie, and A. J. Shields, “A quantum light-emitting diode for the standard telecom window around 1550 nm,” Nat. Commun. 9, 862 (2018).

Paper details

vlnc:W_m8u4g5kc
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents