betaFeedback

WorksPhysics and Astronomy

Sound Trapping in an Open Resonator

Abstract

The ability of extreme sound energy confinement with high-quality factor (Q-factor) resonance is of vital importance for acoustic devices requiring high intensity and hypersensitivity in biological ultrasonics, enhanced collimated sound emission (i.e. sound laser) and high-resolution sensing. However, structures reported so far demonstrated a limited quality factor (Q-factor) of acoustic resonances, up to several tens in an open resonator. The emergence of bound states in the continuum (BIC) makes it possible to realize high-Q factor acoustic modes. Here, we report the theoretical design and experimental demonstration of acoustic BICs supported by a single open resonator. We predicted that such an open acoustic resonator could simultaneously support three types of BICs, including symmetry protected BIC, Friedrich-Wintgen BIC induced by mode interference, as well as a new kind of BIC: mirror-symmetry induced BIC. We also experimentally demonstrated the existence of all three types of BIC with Q-factor up to one order of magnitude greater than the highest Q-factor reported in an open resonator.

Introduction

Acoustic resonators constitute the fundamental building block for acoustic metamaterials and metasurfaces[1, 2, 3, 4]. They have been widely used in various design, such as acoustic absorbers and wavefront engineering[5, 6]. Typically, most acoustic resonators reported so far have relatively low Q-factor limited to few tens, which may hinder their applications as acoustic sources (e.g. sound laser) and sensors. As a particular type of resonance, bound states in the continuum (BIC), also referred to as embedded trapped modes, have triggered extensive interest within the photonic community because they support zero radiative decay rate and infinite Q-factor[7, 8, 9, 10, 11, 12, 13], allowing for enhanced light-matter interaction[14, 15, 16, 17]. In analogue with photonic BICs, acoustic systems such as a rigid plate in a waveguide and axisymmetric duck-cavity, also support BICs when losses are neglected[18, 19, 20, 21, 22, 23]. However, all of these studies are theoretical works. More recently, the first experimental demonstration of quasi-BIC was done with a two-cavity system by breaking the symmetry[24], where the measured Q-factor was only around 50. In this work, we demonstrate that an open acoustic resonator could simultaneously support three types of BICs, including symmetry protected BICs (Figure 1a-Figure 1b), mode interference induced BICs (Figure 1c-Figure 1d), as well as newly observed mirror-symmetry induced BICs (Figure 1e-Figure 1f). We also experimentally confirm the existence of these BICs. The measured Q-factors for these BICs are up to 250, 583, and 393, respectively. To the best of our knowledge, these are the largest Q-factors of acoustic resonances reported so far.

Image not extracted

Figure 1. BIC in an open acoustic resonator. a, Symmetry-protected BIC. b, Transmission spectra evolution as structure asymmetry is introduced. When the asymmetry ratio decreases to 0 (black curve), ideal BIC occurs. c, Friedrich-Wintgen BIC induced by mode interferences. d, Resonant frequency of

Results and discussion

We start by investigating the eigenmode properties of Helmholtz-like resonator system shown in Figure 2a. Such an open system can be treated as a closed rectangular acoustic cavity suject to deformation. A small air gap is opened to introduce the interaction between the cavity and the exterior environment. The role of the acoustic waveguide connecting to the neck is to guide the incoming acoustics waves, enabling measurement in experiments, as will be described in the later section. Because of its non-Hermitian nature, this open system turns the closed cavity modes into leaky modes (also denoted as quasinormal modes). The leaky modes have complex eigenfrequencies ω=ω0−iγ\omega=\omega_0-i\gamma, where ω0\omega_0 and γ\gamma are the resonant frequency and radiative decay rate, respectively. The radiative Q-factor can be derived from Q=ω0/(2γ)Q=\omega_0/(2\gamma). Here, each leaky mode's complex eigenfrequency is calculated by COMSOL Multiphysics. Following the definition in [20], the leaky modes are labelled as MpqM_{pq}, where pp and qq are the number of maxima in the pressure field along the xx- and yy-axes, respectively.

Image not extracted

Figure 2. BIC in an open acoustic resonator. a, Schematic drawing of an open acoustic resonator, where an acoustic waveguide is coupled to a rectangular resonator. b, Q-factor of mode M12_{12} vs neck width. c, Q-factor of mode M12_{12} vs ycy_c. d, eigenfrequency kLykL_y of mode M41_{41} and M23_{23} vs size ratio in a closed resonator. e, eigenfrequency kLykL_y of mode M41_{41} and M23_{23} vs size ratio in an open resonator. f, Q-factor of mode M41_{41} and M23_{23} vs size ratio in an open resonator. g, Q-factor of mode M13_{13} in a half-open resonator. h, Q-factor of mode M13_{13} in a full resonator. i, Q-factor of mode M13_{13} in another half resonator.

We demonstrate that the reflection or transmission spectrum of such Helmholtz resonators can be perfectly reproduced with a complex eigenfrequency of leaky modes based on coupled-mode theory (CMT)[25] (See § 1 and Fig. S1 in supporting material (SM)). Thus, the goal in searching BICs is to find leaky modes with infinitely large QQ-factor. Since a BIC is also accompanied by vanishing linewidth of the acoustic resonance in the reflection or transmission spectrum, we calculate the reflection coefficient as a function of frequency and size ratios in Fig. S2 while assuming the system is lossless. Many BICs can be found by checking the vanishing linewidth of resonant peaks. These BICs can be categorized into three types (See Figure 1): symmetry protected BICs (Figure 1a-Figure 1b), Friedrich-Wintgen BICs induced by two mode interference (Figure 1c-Figure 1d) and mirror-effect induced BICs (Figure 1e-Figure 1f). Except where explicitly mentioned, only the lossless case is studied for calculating the leaky modes. The realistic system's losses will deteriorate the total quality factor by 1/Q=1/Qabs+1/Qrad1/Q=1/Q_{\rm abs}+1/Q_{\rm rad} and will be discussed in the experiment section.

high-Q and low-Q modes as a function of size ratio of the open resonator. e, Mirror-induced BIC for mirror along the x-axis. f, Mirror-induced BIC for mirror along the y-axis.

Symmetry-protected quasi-BIC

Referring to Figure 2a, we consider a rectangular cavity of dimensions LxL_x by LyL_y. If only one open port is introduced on the left of the acoustic resonator, symmetry is broken along the y axis but still maintained along the x axis. Thus, it will support several symmetry protected BICs as long as the centre of neck and resonator are symmetric with respect to the x-axis. The left waveguide's existence will further lead to broken symmetry along the x-axis, and thus turn an ideal BIC into a quasi BIC. Without loss of generality, we use mode M12M_{12} in the square cavity as an example to describe the effect of neck width ww and centre shift ycy_c on the Q-factor of BIC. Interestingly, from Figure 2b, the Q factor is still larger than 10410^4 for the system with protected symmetry along the y axis even when the neck's width is half of the right cavity width. The Q-factor increases exponentially with decreasing neck width. This can be understood by treating the neck as a perturbation of the square cavity. The smaller neck width, the smaller the perturbation, and thus the larger the Q-factor is. Another interesting finding is that the Q-factor is proportionally to 1/(yc)21/(y_c)^2 when the neck width is small compared to the width of the right cavity, as shown in Figure 2c. This phenomenon has been observed and proved for BIC in photonic systems[26]. Additional symmetry protected quasi BICs can be found in such structures as long as q is even number for mode MpqM_{pq}(See Fig. S3).

Friedrich-Wintgen BIC induced by mode interference.

Friedrich and Wintgen demonstrated that in quantum mechanics full destructive interferences of two degenerate modes gives rise to the avoided crossing of eigenvalues, accompanied by the formation of a BIC[27]. This type of BIC can be easily constructed in our system by tuning the size ratio of a rectangular cavity. For a closed rectangular cavity, cavity modes MpqM_{pq} and Mp+2,q−2M_{p+2,q-2} will become degenerate at a certain size ratio. When an air gap is introduced on one side of the rectangular cavity, strong coupling between these two modes results in the giant enhancement of Q-factor for one mode but suppresses it for another. We use paired modes M23M_{23} and M41M_{41} as an example to illustrate this principle. The pressure distributions for these two modes are shown in the inset of Figure 2d. It is found that the eigenfrequencies for these two modes cross at R=Lx/Ly=1.42R=L_x/L_y=1.42 in a closed cavity. All the eigenmodes become leaky modes with complex eigenfrequencies when introducing the neck to couple the acoustic waveguides to the cavity. Based on the eigenmodes analysis, we find that the real part of eigenfrequencies exhibits an avoided crossing. Simultaneously, the Q-factor for mode M23M_{23} is enhanced to a maximum of 6.87×1076.87 \times10^{7} but suppressed to minimum 86.76 for mode M41M_{41} at R=1.398R=1.398, as shown in Figure 2e-Figure 2f.

Moreover, the avoided crossing suggests that these two modes interchange with each other after the size ratio passes through the critical size ratio. This interesting phenomenon is confirmed by the mode evolution, as shown in Fig.S4. Indeed, the upper branch mode, for example, evolves from mode M23M_{23} into mode M41M_{41} when the size ratio increases from 1.3 to 1.5. Following a similar strategy, more BIC induced by mode interference, such as M13M_{13}-M33M_{33} and M33M_{33}-M51M_{51}, can be found by merely constructing avoided crossing (See Fig.S5a-d). Besides, we find that BIC can also be found in mode crossing for M24M_{24} and M42M_{42} (See Fig.S5e-f). Here, we emphasize that not all crossings of two modes of a closed cavity can bring about BICs. The two modes must have the same parity along both xx- and yy-directions. This is also the reason why we choose paired modes MpqM_{pq} and Mp+2q−2M_{p+2q-2} here.

Mirror-induced BIC

In addition to the abovementioned two types of BICs that have been intensively studied in the photonics community, we also find a new type of BIC: mirror-symmetry induced BIC (See Figure 1e-Figure 1f). Because all the outer boundary conditions are set as a hard wall in simulation, we can view the rightmost boundary as a partial mirror. All the eigenmodes with almost symmetric pressure distribution in the full-size resonator can also be found in a half-size resonator. Thus, many other BICs can also be constructed by simply shrinking the width to half based on this mirror effect. For example, one can easily find a BIC at R=0.498R=0.498 for mode M13M_{13} (Figure 2g), which is indeed half of the critical size ratio for BIC M13M_{13} in a full resonator (Figure 2f).

Moreover, we find that the mirror effect also occurs for the xx-axis. As shown in Figure 2i, a BIC can be found at R=1.986R=1.986. Following a similar approach, more BICs can be constructed (See Figs.S6-7). The mirror effect indicates that one can achieve extreme pressure confinement even with reduced size in the 2D case, suggesting an effective way to engineer the Purcell factor that is the key to realize enhanced acoustic emission[28].

Note that the above three BIC types are not limited to regular rectangular shaped resonators. We can also find them in the elliptical resonator (See Figs.S8). The only difference is that the size ratio is defined as R=a/bR=a/b, where aa and bb are semi-major and semi-minor axes, respectively. Besides, the conclusion drawn in the 2D case can be straightforwardly generalized to three-dimensional (3D) open resonators (e.g. cuboid resonators) (See Figs.S9-11). More freedom is provided in the 3D case because three parameters including length, width and height, are involved in the mode calculation.

Experimental verification of BIC

Next, we switch to the experimental demonstration of all three types of BICs. We fabricate two acoustic cuboid resonators shown in Figure 3a: full resonator and half resonator. In experiments, the left circular tube's diameter is fixed as d=29mmd=29\mathrm{mm} while the length, width, and height for the neck are set as 40mm, 20mm, 20mm, respectively. Figure 3b shows the measurement set up while Figure 4a-Figure 4c depicts the structure's schematic. Figure 3c shows the measured transmission spectra for the full resonator and half resonator, and Figure 3d-Figure 3g corresponds to the zoomed-in range in the vicinity of the BICs while Figure 3h shows the pressure distribution of BICs. Excellent agreement can be found between simulation and experiment over the full spectrum (See Fig.S12). Other leaky modes that are not BICs are given in Fig.S13. In the following, we discuss all three types of BIC observed in experiments.

Image not extracted

Figure 3. Experimental verification in an open resonator. a, Image of 3D printed full (left) and half (right) acoustic resonator. b Transmission measurement system. c, Full transmission spectrum in frequency range 2000-6000Hz. Red, blue and magenta lines represent full resonator (Lx=Ly=Lz=60mmL_x=L_y=L_z=60\mathrm{mm}) with yc=zc=0mmy_c=z_c=0\mathrm{mm}, yc=1y_c=1 and zc=0mmz_c=0\mathrm{mm}, and yc=zc=4mmy_c=z_c=4\mathrm{mm}, respectively; Black and green lines represent half resonator (Lx=30mmL_x=30\mathrm{mm}, Ly=Lz=60mmL_y=L_z=60\mathrm{mm}) with yc=zc=0mmy_c=z_c=0\mathrm{mm}, and yc=1y_c=1 and zc=0mmz_c=0\mathrm{mm}. Eight BICs are observed and labelled as 1-8. d-g, zoom in transmission spectrum in frequency range 2700-3200Hz (d),

Image not extracted

Figure 4. a, Schematic drawing of the 3D open resonator. b, Cross-section in XoZ plane for the 3D open resonator. c, Cross-section in XoY plane for the 3D open resonator. d-f, Simulated transmission spectra for full resonator (Lx=Ly=Lz=60mmL_x=L_y=L_z=60\mathrm{mm}) with different ycy_c (d), half resonator (Lx=30mmL_x=30\mathrm{mm}, Ly=Lz=60mmL_y=L_z=60\mathrm{mm}) with different ycy_c (e) and full resonator (Lx=Ly=60mmL_x=L_y=60\mathrm{mm}) for different values of LzL_z (f). g-i, Measured transmission spectra for full resonator (Lx=Ly=Lz=60mmL_x=L_y=L_z=60\mathrm{mm}) with different ycy_c (g), half resonator (Lx=30mmL_x=30\mathrm{mm}, Ly=Lz=60mmL_y=L_z=60\mathrm{mm}) with different ycy_c (h) and full resonator (Lx=Ly=60mmL_x=L_y=60\mathrm{mm}) for different values of LzL_z (i).

4050-4250Hz (e), 4400-5600Hz (f), and 5750-5950Hz (g). h, pressure field distribution of eight BICs in the full and half resonator, which is also correlated to peaks 1-8 in the transmission spectrum.

To study the symmetry protected BIC, we fix Lx=Ly=Lz=60L_x=L_y=L_z=60mm (Lx=30L_x=30mm, Ly=Lz=60L_y=L_z=60mm) for full (half) resonator and only change the centre shift ycy_c and zcz_c for the cuboid resonator with respect to the symmetric axis of the neck. From Figure 3d-Figure 3f, it can be found that there are three symmetry protected BICs. For example, when ycy_c increases from 0 to 1mm for the half resonator, a dip shows at around 2920Hz (green curve), which corresponds to mode M121_{121} (See Figure 3h-BIC 6). However, we did not observe M121_{121} (BIC 1) for the full resonator when the same asymmetry parameter yc=1y_c=1mm is introduced. This can be explained by that this mode's Q-factor decreases relatively slowly with respect to ycy_c and makes the resonance vanish in the low-Q mode background spectrum. Further enlarging ycy_c may help to excite this mode.

Interestingly, another symmetry protected BIC M221_{221} (BIC 2) appears for a full resonator with yc=1y_c=1 (blue curve), evidenced by a shallow dip in the transmission spectrum (See Figure 3e). For mode M222_{222} (BIC 3), it is not enough to introduce the asymmetry by shifting ycy_c. The mode becomes visible in the transmission spectrum when ycy_c and zcz_c are adjusted to 4mm simultaneously, as shown in Figure 3f (magenta curve). We also systematically study the role of ycy_c (or yc=zcy_c=z_c) on the Q factor for BIC mode M121_{121}, M221_{221} and M222_{222}. The simulated and measured transmission spectra for the modes M121_{121} and M221_{221} are presented in Figure 4d-Figure 4e and Figure 4g-Figure 4h, respectively while the cases of M222_{222} can be found in Fig.S14. Good agreement can be found between these two. When ycy_c is reduced to zero, the vanishing line width of resonances indicates the BIC's appearance. The Q-factor can be obtained by fitting the spectrum with the Fano formula[29] (See Section 2 in SI and Fig.S15). Figure 5a-Figure 5b shows the measured Q-factor vs ycy_c for the former two modes while the Q-factor of M222_{222} is put in Fig.S16. The maximum Q-factor for these two modes is only 250, lower than the theoretical prediction (see Figure 5e-Figure 5f). This is because there are loss in the real system due to the thermo-viscous boundary layers, which degrades the Q-factor. Moreover, the Q-factor reduces with the increasing ycy_c, matching the trend of Q-factor vs ycy_c. Here, it is worth noting that the Q-factor for yc=0y_c=0mm should be larger than 250. However, we cannot retrieve the exact value because they are almost indistinguishable from the background, which is exactly the signature of BIC.

Image not extracted

Figure 5. QQ-factor of QBIC. a, Measured QQ-factor of modes A (M121_{121}) and B (M221_{221}) for the half resonator and full resonator as a function of ycy_c. b, Measured QQ-factor of modes A (M131_{131}) and B (M113_{113}) for full resonator as a function of size ratio. c, Measured QQ-factor of modes A (M131_{131}) and B (M113_{113}) for half resonator as a function of size ratio. d, Calculated QQ-factor of modes A (M121_{121}) and B (M221_{221}) for the half resonator and full resonator as a function of ycy_c. e, Calculated QQ-factor of modes A (M131_{131}) and B (M113_{113}) for full resonator as a size ratio function. f, Calculated QQ-factor of modes A (M131_{131}) and B (M113_{113}) for half resonator as a size ratio function.

For the two-mode interference induced BIC, we fix Lx=Ly=60L_x=L_y=60mm and yc=zc=0y_c=z_c=0mm, but only vary LzL_z. The size ratio RxR_x and RyR_y are defined as Rx=Lz/LxR_x=L_z/L_x and Ry=Lz/LyR_y=L_z/L_y, respectively. Thus, we have R=Rx=RyR=R_x=R_y for Lx=LyL_x=L_y. For the fixed Lz=60 mmL_z=60\,\mathrm{mm} (Rx=Ry=1R_x=R_y=1), we can find from Figure 3g that there are two BICs (BICs 4–5) in the range 5750–5950 Hz, where the pressure field distributions are shown in Figure 3h (mode 4 and 5 for the full resonator, and mode 7–8 for the half resonator). Unlike symmetry-protected BICs, these two BICs always exist regardless of the value of ycy_c. Their Q-factors only depend on the size ratio. The simulated and measured transmission spectra for full resonator are presented in Figure 4f and Figure 4i where resonator height LzL_z varies from 59.5 mm to 60.5 mm. The measurement results of the half resonator with different LzL_z can be found in Fig. S17. Figure 4b-Figure 4c shows the Q-factor of two modes as functions of size ratio. For the full resonator case, the maximum Q-factor is 583 at R=1R=1 for mode B (M113M_{113}) while it is 485 at R=1.008R=1.008 for mode A (M131M_{131}). Note that the trend of measured Q factor vs RR deviates from the theoretical prediction (See Figure 5e-Figure 5f) because of inevitable intrinsic loss in the real system. The theoretical calculated Q-factor for mode A is maintained at a high value because the size ratio Rxy=Ly/LxR_{xy}=L_y/L_x is always 1, which is precisely the critical size ratio. For mode B, the Q-factor reaches the maximum at critical size ratio Rx=Ry=1R_x=R_y=1. However, the majority of Q-factors are ranged between 400–500. Such high-Q factors are already good enough for real applications, such as ultra-narrowband acoustic absorbers and enhanced acoustic emission. A similar phenomenon can also be observed for the half resonator. The only difference is that the maximum Q-factor for mode A (BIC 4) and B (BIC 5) are 393 and 327, respectively, which are lower than the full resonator case. The reduction of Q-factor may be attributed to increased thermo-viscous losses arising from the acoustic resonator's smaller volume.

Conclusion

We report the theoretical design of three types of acoustic BICs, including symmetry-protected BICs, modes interference induced BICs and mirror-symmetry induced BICs in a simple open resonator. Different types of BICs can be induced by tuning the resonators' geometrical parameters. Following the design principle, we fabricate such acoustic resonators and experimentally demonstrate these BICs by measuring the transmission spectrum. We found that the largest QQ-factors retrieved from the transmission spectrum are 250, 583 and 393 for symmetry-protected QBIC, modes interference induced QBIC and mirror-symmetry induced QBIC. Such high-QQ factors may bring more possibilities in designing acoustic devices with high performance, such as acoustic filters and acoustic emitters.

Materials and Methods

Simulations

All simulations in this paper are performed with the commercial software COMSOL Multiphysics. The speed of sound and air density is 349 m/s349\ \mathrm{m/s} (corresponding to the experimental temperature of 30∘C30^\circ\mathrm{C}) and 1.29 kg/m31.29\ \mathrm{kg/m^3}, respectively. When calculating the eigenmodes and transmission (or reflection spectrum), we apply perfect matched layer boundaries at the two ends of waveguides to mimic acoustic wave propagation in the infinite space. The other exterior boundaries are set as rigid.

Experiments

The experimental samples are fabricated by 3D-printing technology using laser sintering stereolithography (SLA, 140 μm140\,\mu\mathrm{m}) with a photosensitive resin (UV curable resin), exhibiting a manufacturing precision of 0.1 mm0.1\ \mathrm{mm}. The complex transmission (and reflection) coefficients of the samples are measured using a Brüel & Kjær type-4206T impedance tube with a diameter of 29 mm29\ \mathrm{mm}. A loudspeaker generates a plane wave, and the amplitude and phase of local pressure are measured by four 1/4-inch condenser microphones (Brüel & Kjær type-4187) situated at designated positions. The complex transmission (and reflection) coefficients are obtained by the transfer matrix method.

Acknowledgements

L. Huang and A. E. Miroshnichenko were supported by the Australian Research Council Discovery Project (DP200101353) and the UNSW Scientia Fellowship program. Y. K. Chiang and D. A. Powell were supported by the Australian Research Council Discovery Project (DP200101708), S. Huang, Y. Cheng and Y. Li were supported by National Natural Science Foundation of China (Grants No. 12074286 and No. 11704284).

Author Contributions

L. Huang, Y. K. Chiang and A. E. Miroshnichenko conceived the idea. L. Huang, Y. K. Chiang, and C. Shen, F. Deng performed the theoretical calculation and numerical simulation. S. Huang. Y. Cheng, B. Jia and Y. Li fabricated the sample and performed the reflection/transmission spectra measurements. L. Huang, Y. Li, D. A. Powell, and

A. E. Miroshnichenko supervised the project. All authors discussed the results and prepared the manuscript.

References

  1. [1]Ma, G. & Sheng, P. Acoustic metamaterials: From local resonances to broad horizons. Sci. Adv. 2, e1501595 (2016).DOI
  2. [2]Assouar, B. et al. Acoustic metasurfaces. Nat. Rev. Mater. 3, 460–472 (2018).DOI
  3. [3]Cummer, S. A., Christensen, J. & Alù, A. Controlling sound with acoustic metamaterials. Nat. Rev. Mater. 1, 16001 (2016).DOI
  4. [4]Ma, G., Yang, M., Xiao, S., Yang, Z. & Sheng, P. Acoustic metasurface with hybrid resonances. Nat. Mater. 13, 873–878 (2014).DOI
  5. [5]Li, Y. & Assouar, B. M. Acoustic metasurface-based perfect absorber with deep subwavelength thickness. Appl. Phys. Lett. 108, 63502 (2016).DOI
  6. [6]Li, Y. et al. Experimental Realization of Full Control of Reflected Waves with Subwavelength Acoustic Metasurfaces. Phys. Rev. Appl. 2, 64002 (2014).DOI
  7. [7]Hsu, C. W., Zhen, B., Stone, A. D., Joannopoulos, J. D. & Soljačić, M. Bound states in the continuum. Nat. Rev. Mater. 1, 16048 (2016).DOI
  8. [8]Hsu, C. W. et al. Observation of trapped light within the radiation continuum. Nature 499, 188–191 (2013).
  9. [9]Plotnik, Y. et al. Experimental observation of optical bound states in the continuum. Phys. Rev. Lett. 107, 28–31 (2011).pubmed.ncbi.nlm.nih.gov/22107630
  10. [10]Marinica, D. C., Borisov, A. G. & Shabanov, S. V. Bound states in the continuum in photonics. Phys. Rev. Lett. 100, 1–4 (2008).pubmed.ncbi.nlm.nih.gov/18518374
  11. [11]Monticone, F. & Alù, A. Embedded Photonic Eigenvalues in 3D Nanostructures. Phys. Rev. Lett. 112, 213903 (2014).DOI
  12. [12]Molina, M. I., Miroshnichenko, A. E. & Kivshar, Y. S. Surface Bound States in the Continuum. Phys. Rev. Lett. 108, 70401 (2012).pubmed.ncbi.nlm.nih.gov/22401179
  13. [13]Weimann, S. et al. Compact Surface Fano States Embedded in the Continuum of Waveguide Arrays. Phys. Rev. Lett. 111, 240403 (2013).
  14. [14]Xu, L. et al. Dynamic Nonlinear Image Tuning through Magnetic Dipole Quasi-BIC Ultrathin Resonators. Adv. Sci. 6, (2019).DOI
  15. [15]Kodigala, A. et al. Lasing action from photonic bound states in continuum. Nature 541, 196 (2017).DOI
  16. [16]Koshelev, K. et al. Subwavelength dielectric resonators for nonlinear nanophotonics. Science (80- . ). 367, 288 LP-292 (2020).DOI
  17. [17]Huang, C. et al. Ultrafast control of vortex microlasers. Science (80- . ). 367, 1018 LP-1021 (2020).DOI
  18. [18]Hein, S. & Koch, W. Acoustic resonances and trapped modes in pipes and tunnels. J. Fluid Mech. 605, 401–428 (2008).DOI
  19. [19]Hein, S., Koch, W. & Nannen, L. Trapped modes and Fano resonances in two-dimensional acoustical duct-cavity systems. J. Fluid Mech. 692, 257–287 (2012).DOI
  20. [20]Lyapina, A. A., Maksimov, D. N., Pilipchuk, A. S. & Sadreev, A. F. Bound states in the continuum in open acoustic resonators. J. Fluid Mech. 780, 370–387 (2015).DOI
  21. [21]Evans, D. V. & Linton, C. M. Trapped modes in open channels. J. Fluid Mech. 225, 153–175 (1991).DOI
  22. [22]Vassiliev, D. Existence Theorems for Trapped Modes. J. Fluid Mech. 261, 21–31 (1994).DOI
  23. [23]Davies, E. B. & Parnovski, L. Trapped modes in acoustic waveguides. Q. J. Mech. Appl. Math. 51, (1998).DOI
  24. [24]Huang, S. et al. Extreme Sound Confinement From Quasibound States in the Continuum. Phys. Rev. Appl. 14, 21001 (2020).DOI
  25. [25]Fan, S., Suh, W. & Joannopoulos, J. D. Temporal coupled-mode theory for the Fano resonance in optical resonators. J. Opt. Soc. Am. A 20, 569–572 (2003).pubmed.ncbi.nlm.nih.gov/12630843
  26. [26]Koshelev, K., Lepeshov, S., Liu, M., Bogdanov, A. & Kivshar, Y. Asymmetric Metasurfaces with High-$Q$ Resonances Governed by Bound States in the Continuum. Phys. Rev. Lett. 121, 193903 (2018).DOI
  27. [27]Friedrich, H. & Wintgen, D. Interfering resonances and bound states in the continuum. Phys. Rev. A 32, 3231–3242 (1985).pubmed.ncbi.nlm.nih.gov/9896488
  28. [28]Landi, M., Zhao, J., Prather, W. E., Wu, Y. & Zhang, L. Acoustic Purcell Effect for Enhanced Emission. Phys. Rev. Lett. 120, 114301 (2018).DOI
  29. [29]Miroshnichenko, A. E., Flach, S. & Kivshar, Y. S. Fano resonances in nanoscale structures. Rev. Mod. Phys. 82, 2257–2298 (2010).DOI

Paper details

vlnc:W_nh63bs8r
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents