betaFeedback

WorksPhysics and Astronomy

Darcy plume oscillations at low injection velocities

Abstract

We numerically investigate miscible buoyancy-driven Darcy plumes at low injection velocities. Below a critical injection velocity, the steady plume becomes unstable and develops periodic oscillations. Approaching the critical velocity, the oscillation amplitude vanishes while the frequency remains finite at the critical point, consistent with a supercritical Hopf bifurcation, whereas at lower injection velocities increasingly complex dynamics emerge. Unsteadiness also strongly enhances lateral mixing, increasing the mixing-layer thickness by a factor of approximately 2-3 compared with a steady plume. These findings reveal a previously unexplored dynamical regime of Darcy plumes with important consequences for subsurface transport and leakage.

Introduction

Buoyancy-driven flow in porous media arises in many geophysical and environmental applications, including geological carbon sequestration, contaminant transport in aquifers, saltwater intrusion, and geothermal heating systems ([13]; [21]; [12]; [5]; Di et al. 2025; [15]; [2]). When a lighter fluid is injected vertically into a porous medium saturated with a denser ambient fluid, the density difference generates buoyancy forces that drive the upward migration of the injected fluid, forming a buoyancy-driven Darcy plume ([14]; [11]; [4]; [6]; [16]). Meanwhile, during transport downstream, lateral diffusion and mixing occur, causing the plume to widen and dilute ([18]; [10]).

In miscible systems, local changes in concentration lead to changes in density, which in turn alter the local buoyancy and the Darcy velocity. In this coupled flow–concentration system, the natural buoyancy velocity scale, wbw_b, can be derived from Darcy’s law, namely

wb=KΔρgμ,(1)w_b = \frac{K\Delta\rho g}{\mu}, \tag*{(1)}

where KK is the permeability of the porous medium, Δρ>0\Delta\rho> 0 is the density difference between the fluids, μ\mu is the dynamic viscosity, and gg is gravitational acceleration.

Motivated by understanding leakage dynamics near geological faults during CO2\mathrm{CO}_2 sequestration, as well as other environmental leakage flows, such as contaminant release in aquifers ((Bear & Cheng 2010; Huppert & Neufeld 2014; Gilmore et al. 2022; Benham 2023a,b; Di et al. 2026)), we focus on fluid injection from a constant flux point source. Within this context, a key parameter governing the problem is the ratio WW between the injection velocity at the source w0w_0 and the buoyancy velocity Eq. (1) ([4]), such that

W=w0wb.(2)W = \frac{w_0}{w_b}. \tag*{(2)}

This quantifies the relative strength of the imposed source compared to the buoyancy. As described by Benham [4], the near-field shape of the plume (in the case of a macroscopic sharp interface) is fully determined by WW, with W<1W < 1 leading to locally thinning plumes, and W>1W > 1 to locally thickening plumes, with steady plume shapes found for WW values in the range 0.12 − 1.14.

The size of w0w_0 and hence WW is determined by the properties of the inlet, such as the fault geometry and permeability ([10]). In the case where the driving pressure head is small compared with the pressure head across the fault, or when the fault permeability is small compared to the reservoir permeability, this leads to small values of W≪1W \ll1. Such cases are associated with plumes that thin dramatically near the inlet, causing large, negative, flow-enhancing pressures locally that play a significant role on leakage dynamics. However, it was shown by Benham [4] that below a critical value W<Wc≈0.5W < W_c \approx0.5, steady plume shapes become linearly unstable due to the fact that the steep plume shape cannot support the unstable density difference locally (essentially a Rayleigh-Taylor instability). In addition, there is a lower critical value W0=0.12W_0 = 0.12, below which no steady plume shape appears to exist, raising questions about the fate of the Darcy plume for such small inlet velocities.

However, beyond predicting the instability and the disappearance of steady solutions at sufficiently low WW, this has never been explored further, nor is it known what occurs after the onset of the instability. Hence, for small WW values, the long-time evolution of the plume shape remains unclear, as well as the impact on concentration transport and mixing with the ambient fluid.

To address the above issues, this study uses numerical simulations to investigate the unsteady behavior of buoyancy-driven miscible Darcy plumes at low inlet velocities. The reliability of the numerical model is verified by comparing it with experimental results and theoretical solutions for steady states and then extended to simulate unsteady states. We find that the unsteady Darcy plume can enter a periodic oscillation (or limit cycle) with a characteristic frequency and an amplitude that diminishes as the critical value WcW_c is reached, which is consistent with a supercritical Hopf bifurcation, similar to the case of a dripping faucet ([17]).

Numerical model

We numerically investigate the buoyancy-driven Darcy plume in a saturated two-dimensional porous medium. The governing equations consist of the continuity equation, Darcy’s law, and the advection-diffusion equation, given by

∇⋅U=0,(3)\nabla\cdot\mathbf{U} = 0, \tag*{(3)}
U=−Kμ(∇P+ρ(c)gez),(4)\mathbf{U} = -\frac{K}{\mu}\left(\nabla P + \rho(c)g\mathbf{e}_z\right), \tag*{(4)}
ϕ∂c∂t+∇⋅(cU)=ϕD∇2c.(5)\phi\frac{\partial c}{\partial t} + \nabla\cdot(c\mathbf{U}) = \phi D\nabla^2 c. \tag*{(5)}

Here, U(x,z,t)\mathbf{U}(x,z,t) is the Darcy velocity, P(x,z,t)P(x,z,t) is the pressure, c(x,z,t)c(x,z,t) is the concentration, ϕ\phi is the porosity, and DD is the diffusion coefficient. The viscosity μ\mu is assumed to be independent of concentration. The density ρ(c)\rho(c) is assumed to vary linearly with concentration, written as

ρ(c)=ρl+(ρh−ρl)c,(6)\rho(c) = \rho_l + (\rho_h - \rho_l)c, \tag*{(6)}

where ρl\rho_l and ρh\rho_h are the constant densities of the light and dense fluids. Therefore, c=0c = 0 denotes the light fluid and c=1c = 1 the dense fluid. We ignore the effects of mechanical dispersion for simplicity, although these could be explored by adding an effective diffusion tensor that depends on the local flow velocity Woods [21].

We implement the governing equations using a finite-volume formulation in the open-source computational-fluid-dynamics platform OpenFOAM® Weller et al. [20]. The computational domain is discretized using approximately 5×1055 \times10^5 cells, with local mesh refinement near the plume inlet and the interfacial region between two fluids. The pressure and concentration equations are solved to absolute tolerances of 10−810^{-8} and 10−910^{-9}, respectively. Utilizing symmetry about the vertical axis, only half of a plume is investigated within a square computational region (Lx×Lz=0.4 m×0.4 mL_x \times L_z = 0.4\ \mathrm{m} \times0.4\ \mathrm{m}). We follow the experimental parameters of Gilmore et al. [10], in which salty water is injected into the top of a reservoir of porous beads saturated with fresh water. In those experiments, the salty water forms a dense plume that sinks downwards. Since we are interested in rising plumes (which are more relevant for most environmental applications), we reverse the fluids, such that buoyant fresh water is injected into the bottom of a reservoir filled with salty water. Under the Boussinesq approximation, the flow patterns should remain equivalent despite the vertical flipping (Amooie et al. 2018). As described by Gilmore et al. [10], the permeability and porosity of the porous beads were estimated as K=1.06×10−8 m2K = 1.06 \times10^{-8}\ \mathrm{m}^2 and ϕ=0.41\phi= 0.41.

The chosen idealised boundary conditions are summarised as follows. The left side x=0x = 0 is set as a symmetry boundary, while the top and right boundaries (z=Lzz = L_z, x=Lxx = L_x) are set as outlets with hydrostatic pressure. On the bottom boundary z=0z = 0, a velocity inlet of width a0=0.03a_0 = 0.03 m is located at the lower-left corner, and the remainder of the bottom boundary is impermeable. Initially, the domain is saturated with saline water (ρh=1030\rho_h = 1030 kg/m3^3; μ=0.001\mu= 0.001 Pa·s). Fresh water with lower density and the same viscosity (ρl=998\rho_l = 998 kg/m3^3; μ=0.001\mu= 0.001 Pa·s) is then injected through the inlet at constant vertical velocity w0w_0. As such, the inlet buoyancy velocity (before mixing) is estimated as wb=3.33×10−3w_b = 3.33 \times10^{-3} m/s. We take the molecular diffusivity of salt in water as D=1.5×10−9D = 1.5 \times10^{-9} m2^2/s. Hence, defining the Péclet number as Pe=wba0/D\mathrm{Pe} = w_b a_0/D, we find Pe≈6.6×104\mathrm{Pe} \approx6.6 \times10^4 (although a range of Pe values are studied later in § 3.4). Based on this numerical configuration, we vary WW via w0w_0 to investigate the dynamics of the Darcy plume.

Results

Comparison with experiments and theory for steady states

We begin by testing the validity of the numerical model. We first compare the results of numerical simulations with the steady Darcy plume observed in experiments of salty and fresh water in a tank of porous beads (Gilmore et al. [10]), as shown in Figure 1. As can be seen in Figure 1(a,Figure 1b), for both cases (W=0.58W = 0.58 and W=0.74W = 0.74), the numerical simulations successfully reproduce the experimental plume shape, and the near-field regions of the plumes are fundamentally consistent. We further compare the numerical simulations with the theoretical solution for the near-field interface of steady Darcy plumes in the absence of mixing (Benham [4]). In the case where W≈1W \approx1 it was shown that the plume half-width a(z)a(z) approximately satisfies the differential equation

Figure 1. Validation of the numerical model for steady plume shapes. (a,b) Comparison between experimental observations of fresh and salty water in a tank of porous beads Gilmore et al. [10] and numerical simulations for W=0.58W = 0.58 and W=0.74W = 0.74. Experimental photos are partially obstructed by a clamp.

a′(z)≈−(1−W)4πtanh⁡−1[exp⁡(−πz2a0)].(7)a'(z) \approx-(1-W)\frac{4}{\pi}\tanh^{-1}\left[\exp\left(-\frac{\pi z}{2a_0}\right)\right]. \tag*{(7)}

where a0=a(0)a_0 = a(0) is the inlet half-width. Equation (7) predicts locally widening, straight and narrowing plumes for W>1W > 1, W=1W = 1 and W<1W < 1, respectively. As shown in Figure 2, the numerical results reproduce the theoretical near-field plume shapes fairly well, providing a basis for investigating the unsteady dynamics at lower WW.

Comparison between theoretical solutions and numerical simulations for intermediate values of $W$

Figure 2. Comparison between theoretical solutions (7) (yellow lines) and numerical simulations for intermediate values of WW.

Unsteady near-field dynamics

Now, we reduce WW to investigate the near-field dynamics as buoyancy becomes increasingly important relative to the imposed source injection. To quantify the plume dynamics, we define the plume flux across a horizontal section as

Q(z,t)=∫0Lx[1−c(x,z,t)]w(x,z,t) dx.(8)Q(z,t) = \int_{0}^{L_x} [1-c(x,z,t)]w(x,z,t)\,\mathrm{d}x. \tag*{(8)}

The corresponding flux fluctuation is

Q′(z,t)=Q(z,t)−Q(z,t)‾,(9)Q'(z,t) = Q(z,t) - \overline{Q(z,t)}, \tag*{(9)}

where the overbar denotes a temporal average over the developed state. Furthermore, we introduce the following dimensionless quantities

Q′∗=Q′a0wb,t∗=twba0,Q˙′∗=Q˙′wb2,f∗=fa0wb,(10)Q^{\prime*} = \frac{Q'}{a_0w_b}, \qquad t^* = \frac{tw_b}{a_0}, \qquad\dot{Q}^{\prime*} = \frac{\dot{Q}'}{w_b^2}, \qquad f^* = \frac{fa_0}{w_b}, \tag*{(10)}

where ff is the frequency of oscillation, and dots denote time derivatives.

Figure 3 shows the transition from strongly unsteady plumes at low WW to steady plumes above a critical value Wc≈0.25W_c \approx0.25. At low WW, near-source fluctuations strongly deform the plume and enhance mixing, whereas above WcW_c a stable plume forms with mixing confined to a thin interfacial layer.

Numerical observations of unsteady Darcy plumes for small $W$

Figure 3. Numerical observations of unsteady Darcy plumes for small WW. First row: evolution of Darcy plume at W=0.2W = 0.2; Second row: Comparison of Darcy plumes under low WW conditions at t∗=200t^* = 200.

The critical value Wc≈0.25W_c \approx0.25 is smaller than the sharp-interface prediction Wc≈0.5W_c \approx0.5 of Benham [4], suggesting that diffusion may have a stabilising effect on the strongly thinned near-source plume (in fact, later in § 3.4 we show how WcW_c varies with Pe\mathrm{Pe}). The predicted disappearance of unstable steady states below W0≈0.12W_0 \approx0.12 cannot be directly assessed here, since such states are not realised dynamically.

Figure 4a shows a transition from steady behaviour at W=0.30W = 0.30 to coherent oscillations at W=0.20W = 0.20 and 0.100.10, and increasingly irregular oscillations at W=0.05W = 0.05. Figure 4b shows that the oscillations have approximately the same period throughout the plume, while their amplitude is largest near the inlet and decays downstream, demonstrating spatially coherent oscillatory behaviour.

Figure 4. Unsteady plume dynamics in the near field. (a) Time series of the dimensionless flux fluctuation Q′∗Q^{\prime*} at z/a0=4z/a_0 = 4 for representative values of WW. (b) Time series of Q′∗Q^{\prime*} at different downstream locations (z/a0=1,2,4,z/a_0 = 1, 2, 4, and 66) for W=0.20W = 0.20. (c) Phase trajectories in the (Q′∗,Q˙′∗)(Q^{\prime*}, \dot{Q}^{\prime*}) plane at z/a0=4z/a_0 = 4. (d) Distribution of the dimensionless FFT amplitude A∗A^* as a function of dimensionless frequency f∗f^* and WW at z/a0=4z/a_0 = 4.

The phase portraits in Figure 4c further demonstrate the transition from a steady state to closed periodic trajectories, which become increasingly irregular at low WW. Correspondingly, the dimensionless spectral amplitude A∗A^* in Figure 4d (obtained via Fast Fourier Transform) shows a distinct dominant frequency f∗f^* for 0.06≲W<Wc0.06 \lesssim W < W_c, together with higher harmonics. For W<0.06W < 0.06, the spectrum broadens, indicating increasingly complex dynamics, whereas for W>WcW > W_c the coherent spectral features disappear.

The periodic behaviour can be interpreted as a repeated cycle of plume thinning and Rayleigh–Taylor instability near the source. At low injection velocities, buoyancy strongly narrows the plume, producing a locally unstable density configuration that deforms the plume and releases a buoyant parcel of fluid upwards. This deformation temporarily relaxes the unstable configuration, before continued injection re-establishes the narrow plume and the cycle repeats.

Unsteady near-field lateral mixing

Next, we examine how the unsteady Darcy plume affects the near-field mixing. For a steady plume, the concentration distribution on the plume interface can be approximated. by a hyperbolic tangent function

c(x,z)=12[1+tanh⁡(x−xc(z)δ(z))],(11)c(x,z) = \frac{1}{2}\left[1+\tanh\left(\frac{x-x_c(z)}{\delta(z)}\right)\right], \tag*{(11)}

where xc(z)x_c(z) denotes the centre of the concentration transition and δ(z)\delta(z) is its characteristic mixing-layer thickness. The parameters xcx_c and δ\delta are obtained by fitting Eq. (11) to the numerical concentration profile using a least-squares method at a given zz value.

Figure 5a shows the time-averaged concentration profile of a steady plume under the conditions W=0.30W = 0.30 and z/a0=4z/a_0 = 4. The numerical profile is well described by Eq. (11), as shown by the fit. By contrast, in the unsteady case shown in Figure 5b, where W=0.20W = 0.20, the concentration distribution exhibits a significant non-monotonic deformation, which cannot be described by (3.5).

Figure 5. Unsteady near-field mixing. (a) Concentration profile for the steady plume at W=0.3W = 0.3 and z/a0=4z/a_0 = 4, together with the hyperbolic-tangent fit. The fitted centre xcx_c and characteristic thickness δ\delta are indicated. (b) Concentration profile and hyperbolic-tangent fit for unsteady plume at W=0.2W = 0.2. (c) Magnitude of the parameter ∣ϵ∣|\epsilon| (12) as a function of WW at z/a0=4z/a_0 = 4, quantifying the departure of the time-averaged concentration profile from the hyperbolic-tangent representation. (d) Downstream evolution of the alternative mixing-layer thickness Δ/a0\Delta/a_0 for unsteady (W=0.2W = 0.2) and steady (W=0.3W = 0.3) plumes.

To quantify this deviation from the hyperbolic tangent distribution, we define

ϵ(z)=12δ(z)∫0Lx4cˉ(x,z)(1−cˉ(x,z)) dx−1,(12)\epsilon(z) = \frac{1}{2\delta(z)}\int_{0}^{L_x}4\bar{c}(x,z)\left(1-\bar{c}(x,z)\right)\,\mathrm{d}x - 1, \tag*{(12)}

where cˉ\bar{c} denotes the time-averaged concentration. For the hyperbolic tangent distribution, ϵ=0\epsilon= 0; whereas an increase in ∣ϵ∣|\epsilon| indicates a larger deviation from the prescribed distribution. Figure 5c shows that when WW is larger than the critical value WcW_c, ∣ϵ∣|\epsilon| remains small; however, as WW decreases below WcW_c, leading to unsteady states, ∣ϵ∣|\epsilon| increases markedly. Note that to calculate ϵ\epsilon, δ\delta is obtained from the best-fit profile even when the concentration distribution deviates from (3.5).

We define an alternative mixing-layer thickness Δ(z)\Delta(z) as the difference between the 5% and 95% time-averaged concentration values, such that

Δ(z)=x(cˉ=0.95)−x(cˉ=0.05).(13)\Delta(z) = x(\bar{c} = 0.95) - x(\bar{c} = 0.05). \tag*{(13)}

Figure 5d compares the downstream evolution of Δ(z)\Delta(z) for W=0.20W = 0.20 and 0.300.30. For the steady plume at W=0.30W = 0.30, Δ/a0\Delta/a_0 remains at a relatively small value and is almost independent of the downstream distance. In contrast, the unsteady plume at W=0.20W = 0.20 exhibits a significantly wider mixing layer (by a factor of approximately 2-3), which gradually widens downstream. Thus, the unsteady plume exhibits significantly enhanced lateral mixing, with interface deformation promoting mixing by molecular diffusion.

Bifurcation behaviour and parameter dependence

The above results indicate that near-field Darcy plumes maintain oscillatory behaviour for a range of WW values. We now identify the bifurcation behaviour between unsteady and steady states near the critical value W≈WcW \approx W_c. Figure 6a shows the oscillation envelopes of Q′∗Q^{\prime*} at several downstream locations. As W→Wc−W \to W_c^{-}, the oscillation amplitude vanishes at Wc≈0.25W_c \approx0.25, while the dominant frequency remains finite (f∗=0.65f^* = 0.65–0.680.68), which is consistent with a supercritical Hopf bifurcation. This behaviour is reminiscent of the dripping-faucet problem, which similarly exhibits a Hopf bifurcation, where a steady stream switches to periodic dripping and eventually chaos as the flow rate is reduced [17, 7, 19].

Figure 6. Bifurcation behaviour and near-field pressure. (a) Upper and lower envelopes of the dimensionless flux fluctuation Q′∗Q^{\prime*} as functions of WW, evaluated at z/a0=1,4z/a_0 = 1, 4. (b) Critical injection velocity ratio WcW_c as a function of the Péclet number PePe at z/a0=4z/a_0 = 4. (c) Dimensionless pressure p∗p^* at z=0z = 0 for different values of WW. (d) Mean and minimum dimensionless pressure as functions of WW.

Figure 6b shows the influence of molecular diffusion on the instability via the Péclet number. As Pe increases, WcW_c increases towards a diffusion-independent limit, while at sufficiently small Pe the oscillations disappear altogether. Thus, diffusion stabilises the plume and partly accounts for the difference between the present critical value and the sharp-interface prediction [4].

Finally, Figure 6c,Figure 6d show the dimensionless pressure near the inlet (p∗=p/Δρga0p^* = p/\Delta\rho g a_0 at z=0z = 0) associated with the strongly thinning near-field plume. The pressure decreases sharply near the inlet, producing a pronounced local pressure minimum for small WW. This negative pressure is a consequence of the buoyancy-driven acceleration of the thinning plume and has important implications for leakage flows, as discussed below.

Conclusions

This study has revealed a previously unexplored unsteady regime of miscible buoyancy-driven Darcy plumes at low injection velocities. Below a critical value WcW_c, the steady plume gives way to periodic oscillations associated with repeated near-source thinning and Rayleigh–Taylor instability. The oscillation amplitude vanishes while the dominant frequency remains finite as W→Wc−W \to W_c^{-}, consistent with a supercritical Hopf bifurcation, while increasingly complex dynamics emerge at still lower WW. The critical value depends on molecular diffusion: WcW_c increases with Pe before approaching an approximately constant value in the weak-diffusion limit.

These unsteady dynamics have important consequences for subsurface transport. Plume oscillations strongly deform the concentration field and enhance lateral mixing, producing a mixing layer approximately 2–3 times thicker than that of a steady plume. In addition, the strongly thinning near-source plume generates a pronounced negative pressure near the inlet. For leakage through a permeable fault or pathway whose flux is coupled to the local pressure difference, this negative pressure would act to enhance the driving pressure and hence the leakage rate [10, 4]. Thus, the onset of plume instability can affect not only the subsequent mixing and transport of leaked fluid, but also the leakage rate itself.

The present model neglects mechanical dispersion in order to isolate the effects of molecular diffusion. Future work should examine velocity-dependent dispersion and three-dimensional geometries, both of which may modify the critical conditions and nonlinear plume dynamics. Extensions to immiscible flows would additionally introduce capillary pressure and relative permeability, which may modify the oscillatory instability and plume breakup, with consequences for the migration and leakage of subsurface CO2\mathrm{CO}_2 during geological carbon sequestration [13].

Funding. X.D. acknowledges support from National Natural Science Foundation of China (Grant No. 52501324) and the Fundamental Research Funds for the Central Universities.

Declaration of interests. The authors report no conflict of interest.

Author ORCIDs.

Xiaoning Di https://orcid.org/0009-0005-6433-6149

Graham P. Benham https://orcid.org/0000-0003-1664-6976

Use of AI tools.

ChatGPT (GPT-5.6 Sol, OpenAI) was used during 2026 for copy-editing and language refinement of the manuscript. No scientific results, analyses or figures were generated or modified using AI tools. The authors have reviewed and verified the manuscript and take full responsibility for its content.

References

  1. [2]Bear, J & Cheng, AHD 2010 Modeling Groundwater Flow and Contaminant Transport. Springer: Springer Dordrecht.DOI
  2. [4]Benham, GP 2023b The near-field shape and stability of a porous plume. J. Fluid Mech. 955, A13.DOI
  3. [5]Benham, GP, Bickle, MJ & Neufeld, JA 2021 Two-phase gravity currents in layered porous media. J. Fluid Mech. 922, A7.
  4. [6]Bonazzi, A, Jha, B & de Barros, FPJ 2023 Influence of initial plume shape on miscible porous media flows under density and viscosity contrasts. J. Fluid Mech. 972, A19.DOI
  5. [7]Coullet, P, Mahadevan, L & Riera, CS 2005 Hydrodynamical models for the chaotic dripping faucet. J. Fluid Mech. 526, 1–17.DOI
  6. [10]Gilmore, KA, Sahu, CK, Benham, GP, Neufeld, JA & Bickle, MJ 2022 Leakage dynamics of fault zones: experimental and analytical study with application to co2 storage. J. Fluid Mech. 931, A31.DOI
  7. [11]Hewitt, DR, Peng, GG & Lister, JR 2020 Buoyancy-driven plumes in a layered porous medium. J. Fluid Mech. 883, A37.DOI
  8. [12]Hinton, EM & Woods, AW 2018 Buoyancy-driven flow in a confined aquifer with a vertical gradient of permeability. J. Fluid Mech. 848, 411–429.DOI
  9. [13]Huppert, HE & Neufeld, JA 2014 The fluid mechanics of carbon dioxide sequestration. Annu. Rev. Fluid Mech. 46 (1), 255–272.DOI
  10. [14]Lyu, X & Woods, AW 2016 Experimental insights on the development of buoyant plumes injected into a porous media. Geophys. Res. Lett. 43 (2), 709–718.DOI
  11. [15]Mondal, R, Benham, G, Mondal, S, Christodoulides, P, Neokleous, N & Kaouri, K 2019 Modelling and optimisation of water management in sloping coastal aquifers with seepage, extraction and recharge. J. Hydrol. 571, 471–484.arxiv.org/abs/1901.10810
  12. [16]Panda, S & Sahu, CK 2025 Experimental investigation of early time dynamics of haline plumes in porous media. Phys. Rev. Fluids 10 (5), 054501.DOI
  13. [17]Pinto, RD, Gonçalves, WM, Sartorelli, JC & De Oliveira, MJ 1995 Hopf bifurcation in a leaky faucet experiment. Phys. Rev. E 52 (6), 6986.pubmed.ncbi.nlm.nih.gov/9964209
  14. [18]Sahu, CK & Flynn, MR 2015 Filling box flows in porous media. J. Fluid Mech. 782, 455–478.
  15. [19]Subramani, HJ, Yeoh, HK, Suryo, R, Xu, Q, Ambravaneswaran, B & Basaran, OA 2006 Simplicity and complexity in a dripping faucet. Phys. Fluids 18 (3).DOI
  16. [20]Weller, HG, Tabor, G, Jasak, H & Fureby, C 1998 A tensorial approach to computational continuum mechanics using object-oriented techniques. Comp. Phys. 12 (6), 620–631.DOI
  17. [21]Woods, AW 2015 Flow in Porous Rocks: Energy and Environmental Applications. Cambridge: Cambridge University Press.DOI

Paper details

vlnc:W_q3gvssdz
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

GPT-5.6 Sol (bare)

View statement
Looking for related papers…
Contents