betaFeedback

WorksPhysics and Astronomy

Fast and slow surfactants in turbulence-driven bubble breakup

Abstract

When a large air cavity breaks in a turbulent flow, it goes through very large deformations and cascading events of new interface formation, including elongated filaments and bubbles over a wide range of scales, with their rate of formation controlled by turbulence and capillary processes. We experimentally investigate the effects of surfactants and salt on the fragmentation of a large air cavity, and observe a five fold increase of the number of bubbles being produced in some cases. We characterize the bubble size distribution resulting from successive break-ups in such transient configuration. For bubbles larger than the Hinze scale dHd_H (defined as the balance between surface tension and turbulence stresses), we observe that bubble size distributions remain unchanged for all solutions tested. For bubbles below dHd_H, however, we observe an increase of the number of bubbles produced and an associated steepening of the bubble size distribution upon the addition of surfactant or salt. This later effect is only visible for surfactants with an adsorption timescale that is fast enough compared to the rate at which new interfaces are being generated by turbulence.

Introduction

Gas bubbles dispersed in turbulent flows play a crucial role in mediating the transfer of mass and energy across interfaces ((Mathai et al., 2020)). At the ocean surface, the bursting of bubbles produces sea spray aerosols ([5] (Deike 2022; Deike et al. 2022)), influencing atmospheric and climate processes, while bubbles entrained underwater break ((Deike et al., 2016; Deane & Stokes, 2002)) and influence gas exchange ((Deike & Melville, 2018; Deike, 2022; Deike et al., 2025)). Underwater bubbles transport facilitates oil and gas migration from deep wells, while bubble breakup enhances gas dissolution through increased interfacial area and enhanced mixing in bubble column reactors ((Galinat et al., 2005; Risso, 2018)). Bubbles also play an important role in wastewater treatment, energy systems, advanced manufacturing, food production and agriculture ((Garbin et al., 2025)).

In practical configurations, air-water interfaces are almost always contaminated by surface active agents (surfactants) related to biological or anthropogenic activities. The presence of surfactant modulates surface waves dynamics ((Erinin et al., 2023a)), bubble rise velocity ((Takemura & Yabe, 1999; Tagawa et al., 2014; Farsoiya et al., 2024)), bubble bursting ((Eshima et al., 2025)), with surface tension gradients leading to Marangoni flows, as well as tip streaming leveraged in microfluidics devices to produce droplets ((Eggleton et al., 2001; Rubio & Montero, 2023)). Another practical example of surfactant effects include oil-contaminated surfaces, where surfactants are used in mitigation strategies but also lead to chemical transport by aerosolization (Sampath et al., 2019; Yang et al., 2023). Beyond Marangoni effects, variations in surface tension and sorption kinetics also play important roles (Fernández-Martínez et al., 2025), and comparison between the time scale of adsorption/desorption of surfactant molecules with the characteristic time scale of the flow of interest becomes necessary. A comprehensive understanding of surfactant-mediated bubble behavior is essential for both mitigating environmental impacts of marine pollution and optimizing industrial processes involving gas–liquid interactions.

Here, we consider the effect of surfactant on bubble break-up in a transient configuration, where a large air cavity breaks into small bubbles through successive fragmentation events. The configuration is largely inspired by air entrainment and bubble fragmentation under breaking waves. Bubble fragmentation under breaking waves or in turbulent flows has been widely investigated through both experiments (Deane & Stokes, 2002; Ruth et al., 2022; Ni, 2024) and numerical approaches (Deike et al., 2016; Mostert et al., 2022; Rivière et al., 2021, 2022). Some numerical studies have probed the effect of surfactants in two-phase turbulence [3] (Soligo et al. 2019), and a few experiments investigated the role of salt in bubbly flows [2], but to the best of our knowledge, no systematic studies on the role of surfactants on the distribution of bubbles in turbulence exist.

Bubble breakup in turbulence is understood by considering the competition between inertial stresses from turbulence that promote fragmentation and surface tension forces that resist it. The Weber number, We=ρU2d/γs\mathrm{We} = \rho U^2 d/\gamma_s, which compares these two effects, is commonly used to characterize bubble breakup conditions. Here, dd is the bubble’s volume-equivalent diameter, UU a characteristic velocity defined as the average velocity difference at the bubble-diameter scale, ρ\rho the liquid density, and γs\gamma_s the surface tension. For bubbles within the inertial subrange, the square of the characteristic velocity at the bubble scale is 2ε2/3d2/32\varepsilon^{2/3}d^{2/3}, leading to We=2ρε2/3d5/3/γs\mathrm{We} = 2\rho\varepsilon^{2/3}d^{5/3}/\gamma_s (Rivière et al., 2021). A critical Weber number WecWe_c provides the balance between inertial and surface tension forces, serves as a loose bubble breakup criterion and is of order unity (Martínez-Bazán et al., 1999; Vejrazka et al., 2018; Rivière et al., 2021). The associated length scale is the Hinze scale, dHd_H (Hinze, 1955):

dH=(Wec2)3/5(γsρ)3/5ϵ−2/5,(1)d_H = \left(\frac{We_c}{2}\right)^{3/5}\left(\frac{\gamma_s}{\rho}\right)^{3/5}\epsilon^{-2/5}, \tag*{(1)}

which separates the super-Hinze regime (d>dHd > d_H) in which bubbles will break due to turbulence, from the sub-Hinze regime (d<dHd < d_H). The critical Weber number or Hinze scale is a soft threshold due to the inherent stochasticity of turbulent flows. The super-Hinze bubble size distribution in turbulence or under breaking waves has been described by N(d)∝d−10/3\mathcal{N}(d) \propto d^{-10/3}, explained by a turbulent break-up cascade, controlled by the eddy turn over time at the scale of the bubble Teddy(d)=ϵ−1/3d2/3T_{\mathrm{eddy}}(d) = \epsilon^{-1/3}d^{2/3} (Garrett et al., 2000). In contrast, the sub-Hinze bubble size distribution exhibits a gentler slope, following N(d)∝d−3/2\mathcal{N}(d) \propto d^{-3/2}, which can be explained by a capillary break-up process related to large bubbles experiencing large deformation and the formation of filaments which will then rupture in a time scale controlled by capillarity Tcap(d)=(23)−1(ρ/γs)1/2d3/2T_{\mathrm{cap}}(d) = (2\sqrt{3})^{-1}(\rho/\gamma_s)^{1/2}d^{3/2} (Rivière et al., 2022; Ruth et al., 2022). Both regimes have been extensively documented through laboratory experiments (Ruth et al., 2022; Deane & Stokes, 2002; Qi et al., 2022) and direct numerical simulations (Mostert et al., 2022; Rivière et al., 2022; Crialesi-Esposito et al., 2023; King et al., 2023). The formation of such broad size distribution from an initial air cavity occurs through a sequence of events controlled by the turbulent and capillary time scales, with new interfaces formed along the way.

Figure 1 (a) illustrates the time scales of bubble break-up in turbulence as a function of bubble size dd, using the integral length scale and turbulent dissipation rate estimated in our laboratory experiments. The lengths are normalized by the integral length scale LintL_{\mathrm{int}}, corresponding to the length scale of the larges eddies (≈2.5\approx2.5 cm) and the times are normalized by the associated integral timescale (Tint≈100T_{\mathrm{int}} \approx100 ms).

Image not extracted

Figure 1. (a) Comparisons of the timescales of turbulence, capillary instability and adsorption of the three surfactants used in this study. The length scales are normalized by the integral length scale of turbulence LintL_{\mathrm{int}} and the time scales by the integral time TintT_{\mathrm{int}}. η\eta is the Kolmogorov scale and dinjd_{\mathrm{inj}} is the equivalent diameter of the volume of air initially injected. (b) Schematic of the adsorption dynamics of a fast or slow surfactant during the break-up process. An bubble of size dd intially covered with surfactants is stretched forming filaments, over a typical time Teddy(d)T_{\mathrm{eddy}}(d). The air filament of radius δ\delta fragments in to small bubbles in a time of the order Tcap(δ)T_{\mathrm{cap}}(\delta).

When using surfactants, we now have to consider their relevant time scales and how they compare to capillary and turbulence times which will control break-up and deformation. Marangoni stresses related to gradients in surfactant concentration along the interface will occur on capillary time scales. However, the presence and amount of surfactant on a newly formed interface within a sequence of break-up events will be related to the surfactant adsorption time τads\tau_{\mathrm{ads}}, which controls how fast surfactant in the bulk will make it to the interface (Manikantan & Squires, 2020). As we will demonstrate experimentally, surfactants will influence the multi-scale break-up processes in different ways depending on the characteristic adsorption time of the surfactant, illustrated for Sodium Dodecyl Sulfate (SDS, fast adsorption), Tween 20 (slow adsorption) and Cetrimonium bromide (CTAB, intermediate adsorption timescale) in Figure 1 (a). For SDS, which has a short adsorption time of the order of milliseconds to seconds depending on the concentration [4] (Fainerman et al. 2010), the sorption dynamics will be occurring over a time scale comparable to TeddyT_{\mathrm{eddy}}, allowing SDS molecules to adsorb onto the surface of newly formed bubbles or filaments and influence the breakup process. However, the capillary instability leading to the final break-up will occur on time scales faster than the adsorption. In contrast for Tween 20, which has a long adsorption time of the order of tens of seconds [1] (Qazi et al. 2020), TeddyT_{\mathrm{eddy}} and TcapT_{\mathrm{cap}} are generally shorter than its adsorption time, leaving insufficient time for adsorption during a single set of breakup event. With an intermediate adsorption timescale of order one second (Qazi et al., 2020), CTAB lies between SDS and Tween 20. Its adsorption time is comparable to the integral timescale, TintT_{\mathrm{int}}, allowing adsorption during the breakup process. Consequently, CTAB behaves similarly to Tween 20 at low concentrations and transitions towards SDS-like behaviour as the concentration increases. This observation (illustrated in Figure 1b) will guide the interpretation of our experiments varying surfactant concentration leading to comparable changes in the static surface tension. We note however that the process described here: formation of a dumbbell shape, then ligament rupture; is an idealization of the many processes resulting in sub-Hinze bubble production. Other processes such as direct tearing from a large bubble for instance can also occur but they also involve the formation of a large surface area elongated structure, before capillary rupture.

The paper is organized as follows. Section 2 presents the experimental techniques while Section 3 presents the resulting bubble size distributions, the conclusions are discussed in Section 4.

Experimental methods

Experimental Set-up

Figure 2 (a) shows the schematic diagram for the experimental setup, similar to Ruth et al. (2022). It consists of a polycarbonate tank filled with about 150 L of solution, and a hollow hemispherical metal cup is positioned underwater at the tank center, equidistant from the four corners of the tank where four pumps (Rule 20 DA 800 GPH Bilge Pump) are mounted. The cup initially faces downwards and is filled with a constant volume V0=20V_0 = 20 mL of air. At the beginning of an experiment, the cup is rotated to face upwards while a fast camera (Phantom VEO4K-990-L, 500 fps) is simultaneously triggered.

Image not extracted

Figure 2. (a) Schematic of the experimental setup: air is injected into an upside down cup that is flipped at the beginning of the experiment, and a large air cavity is released into the turbulent flow. (b) Temporal evolution of the total bubble count NN for different SDS concentrations in deionized water. (c) Example of images comparing clean (light blue, bottom), and contaminated cases (dark blue, top, 2000 μmol/L\mu\mathrm{mol}/\mathrm{L} of SDS). The shaded area (2.5Tint∼6Tint2.5T_{\mathrm{int}} \sim6T_{\mathrm{int}}) represents the time range used to compute distributions in the following.

The air cavity is released into the turbulent flow and experiences a sequence of breakups which results in a broad distribution of bubble sizes. Such experimental configuration is designed to characterize the transient fragmentation process of a large air cavity into a distribution of bubbles of various sizes. The high-speed camera is coupled with two different lenses to improve the resolution using multiple views: a large scale view (Nikon Micro 200mm leading to 35 μm\mu\mathrm{m}/pixel) and a zoomed-in view (K2 DistaMax Infinity Photo-Optical Co. lens leading to 9 μm\mu\mathrm{m}/pixel). The field of view is illuminated by a coaxial LED panel from the opposite side. To ensure statistical convergence of the size distribution, each experimental condition is repeated 15 times using the 200mm lens and 25 times using the K2 lens. The depth of field δ(d)\delta(d) was calibrated by translating a target containing 14 chrome-sputtered dots with diameters ranging from 30 μm\mu\mathrm{m} to 3000 μm\mu\mathrm{m} along the optical axis, similarly to

Erinin et al. (2023b). The large scale field of view is processed with a two step algorithm: thresholding for larger bubbles then edge detection on an image where large bubbles have been removed to detect the smaller ones. The small scale field of view is processed using thresholding followed by a filter on the sharpness of the detected objects, to only keep well focused bubbles. We therefore obtain the bubble size distribution N(d)\mathcal{N}(d), defined as the number of bubbles per unit bin size [d,d+Δd][d,d+\Delta d], normalized by the cross sectional area AA of the camera and the depth of field at that given size bin δ(d)\delta(d), and averaged over all realizations. The distributions from the two camera views are combined into a single distribution (see Mazzatenta et al. (2025)). The uncertainties in the distribution is estimated by a Monte Carlo approach in which data are randomly sampled from the repeated experiments using bootstrapping (100 realizations).

Surfactant and salt conditions

There are five different sets of solutions in this study. We used three different surfactants: SDS, CTAB, and Tween 20 used as purchased and mixed with deionized water. We also repeated experiments with SDS and Tween 20, adding a mixture of salts representative of salts present in the ocean (ASTM D1141-98 Artificial Sea Salt, same as in Mazzatenta et al. (2025)). The case with SDS was repeated a second time to ensure robustness. For each experimental case, the solution’s surface tension isotherm was measured at the beginning and end of the experiment using a Langmuir trough (KSV NIMA 1003), and the static surface tension prior to surface compression was recorded as γs\gamma_s. Surfactants concentrations were chosen such that a given set of experiments covers the whole range from clean interfaces to fully contaminated (concentration close to the CMC or surface tension close to 40 mN/m). During all experiments, the tank was closed with an acrylic lid to minimize contamination from ambient air. Experimental conditions are summed up in Table 1.

SurfactantSea SaltConcentration (% CMC)γs\gamma_s (mN/m)dHd_H (mm)d32d_{32} (mm)
SDSNo0–8070–372.1–3.15.2–6
SDSYes0–1.265–392.1–2.96–7.3
Tween-20No0–10072–412.2–3.16.4–6.9
Tween-20Yes0–4072–432.3–3.16.7–8.1
CTABNo0–9071–382.1–3.15.4–6.8

Table 1. Summary of surfactant and solvent conditions tested in the study, with the corresponding evolution of the measured static surface tension γs\gamma_s, the Hinze scale dHd_H computed using (1), and the Sauter mean diameter of the measured distributions d32d_{32}. Concentrations are given as a fraction of the Critical Micelle Concentration (CMC): 8.2 mmol/L for SDS, and 59 μ\mumol/L for Tween 20 and 1 mmol/L for CTAB.

Figure 2(b) presents the temporal evolution of the bubble count, N=∫N(d) ddN = \int\mathcal{N}(d)\,\mathrm{d}d, for experiments conducted with varying concentrations of SDS in deionized water. Across all experimental conditions, NN exhibits a sharp increase immediately after the cup is flipped (t=0t = 0), followed by a quasi-steady plateau over the interval 2.57Tint≤t≤6Tint2.57T_{\mathrm{int}} \le t \le6T_{\mathrm{int}}. The total number of recorded bubbles increases with the concentration of SDS by almost an order of magnitude. Figure 2(c) compares images of the clean case (no surfactants, bottom) and a contaminated case ([SDS] = 2000 μ\mumol/L, top) at t=4Tintt = 4T_{\mathrm{int}}. The scale bar represents 1 cm. A substantial increase in the number of small bubbles is observed in the contaminated case, whereas the population of large bubbles remains nearly unchanged. Similar observations are made when considering the other types of solutions in terms of time evolution (shown in Appendix). Bubble coalescence in the present experiment is expected to be negligible given the low volume fraction of air, as discussed in experiments Ruth et al., 2022 and in simulations Rivière et al., 2021, 2022.

We note that the experiment is transient by design as a large cavity is released and breaks due to turbulence. In our experiment, we observe bubbles generated over a relatively short window after the release (about 1s, or 10Tint10T_{\mathrm{int}}). During that time, bubbles rise to the surface and break and we observe an initial increase in the observed bubbles which plateaus for some time, and would then decrease at much longer times if we were continuing to record as all bubbles get out of the experimental field of view. As we analyze the influence of surfactant on bubble break-up, we will compare the adsorption time with the time in between the break-ups in the sequence, as new area is constantly being created through successive breakups.

Turbulent properties

We measured the turbulent properties of the flow using Particle Image Velocimetry (PIV) in the central plane of the experiment, just over the cup with a field of view slightly larger than the one used in the experiment. The setup, processing and analyses are very similar to the ones described in Ruth et al. (2021). We recorded the flow seeded with tracer particles for 2.5 s with a sampling rate of 1000 frames per second. The data is processed using a standard library for PIV analysis. The mean flow is similar to the one used in Ruth et al. (2022): a small downwards flow just above the cup due to the jets of the pumps meeting in the center (Figure 3 (a)). We estimated the turbulent properties of the flow using the scaling argument in homogeneous and isotropic turbulence De Jong et al. (2009): ε=AURMS3/Lint\varepsilon= A U_{\mathrm{RMS}}^3/L_{\mathrm{int}} with URMSU_{\mathrm{RMS}} the root-mean-square of the velocity fluctuations and LintL_{\mathrm{int}} the integral length scale, using A=0.7A = 0.7 Sreenivasan, 1998. We compute the integral length scale as the maximum of the integral of the autocorrelation of the velocity fluctuations, and average between both directions. Since there is some inhomogeneity in the flow structure, we computed the integral length scale and RMS velocity locally, giving us a local dissipation rate. The resulting integral length scale (cyan lines) and Hinze scale (black circles, using Eq. (1)) are plotted in Figure 3 (b) in several locations in space. The integral length scale is Lint=2.5L_{\mathrm{int}} = 2.5 cm (10%: 2.2, 90%: 2.8), the root-mean-square velocity is URMS=34U_{\mathrm{RMS}} = 34 cm/s (10%: 28, 90%: 42), giving a dissipation rate ε=0.39\varepsilon= 0.39 m2^2s−3^{-3} (10%: 0.22, 90%: 0.75) where the value reported is the median of the spatial distribution and the values in parentheses are the quantiles, showing some inhomogeneity in our setup. The associated Kolmogorov scale is 40 µm and the integral timescale is Tint=101T_{\mathrm{int}} = 101 ms. In Figure 3 (c), we show the second order longitudinal structure function DLL(r)=⟨(Δu(r))2⟩x,tD_{LL}(r) = \langle(\Delta u(r))^2\rangle_{x,t}, in both xx and yy directions. In addition we plot the inertial range scaling, with the dissipation computed from the approach above, and the prefactor C2=2.0C_2 = 2.0 (Pope, 2000). Despite the limited inertial range in our setup, we see that both approaches are consistent. Overall, the flow field in the setup presents strong turbulent fluctuations, required to obtain the breakup of millimetric bubbles and keep them within the field of view long enough so that the size distribution can be recorded. In exchange for this large intensity, the turbulent flow field isn’t homogeneous or isotropic, but we don’t expect those features to affect our conclusions.

Image not extracted

Figure 3. Properties of the turbulent flow field in the setup. Panel (a) shows the mean flow ⟨U⟩\langle U\rangle intensity and direction. Panel (b) shows the RMS velocity in color. The dashed rectangle represents the field of view, the cyan lines show local estimations of the integral length scale LintL_{\mathrm{int}} and the circles show the local Hinze scale dHd_{\mathrm{H}}. Panel (c) shows the second order longitudinal structure functions in both directions. The dashed line is the inertial range scaling, with the prefactor C2=2.0C_2 = 2.0.

Effect of surfactant on bubble production across scales

Representative break-up dynamics with and without surfactant

We qualitatively discuss examples of large bubble break-up in our experiments, leading to populations of sub-Hinze scale bubbles, in presence and absence of surfactant. Figure 4 presents representative examples of the fragmentation process with configurations showing filament formation or shedding behind large bubbles (without surfactants: (a) and (b) and with 4000 µmol/L of SDS: (c) and (d)).

Image not extracted

Figure 4. Representative image sequences illustrating bubble breakup with filament fragmentation and subsequent sub-Hinze bubble generation in presence and absence of surfactant. The initial parent bubble has a size on the order of the Hinze scale. Each row presents four time-resolved snapshots, with a temporal spacing of 1 ms (a, c) or 6 ms (b, d) between consecutive frames. (a) and (b): DI water without surfactant, showing the formation of no or a single sub-Hinze bubble. (c) and (d): 4000 µmol/L of SDS, where several sub-Hinze bubbles are produced.

Rivière et al. (2021, 2022); Ruth et al. (2022); Qi et al. (2022) discuss large bubble breakup in turbulence as happening through two successive stages. First, the parent bubble is deformed by a turbulent eddy with a characteristic length scale comparable to the bubble diameter, over a time-scale controlled by the eddy turn-over time (Teddy∼25T_{\mathrm{eddy}} \sim25 ms in figure 4 (b,d). This interaction stretches the bubble into an unstable configuration consisting of two lobes connected by a thinning neck, as illustrated in figure 4 (b, d). Subsequently, the neck undergoes further thinning under the action of capillary forces, sometimes forming a filament, which ultimately breaks via a Rayleigh–Plateau like instability, over the capillary timescale (Tcap∼0.1−1T_{\mathrm{cap}} \sim0.1 - 1 ms based on the filament thickness in figure 4 b, d), producing small capillary bubbles.

The representations of the sub-Hinze bubble production in figure 4 (b) and (d) could suggest that surfactants influence this mode of production, by increasing the number of child bubbles formed by a single air filament. This configuration is however an idealization of the multiple concurrent fragmentations occurring with the large bubbles used in this study (The injection scale is dinj≈40dHd_{\mathrm{inj}} \approx40d_H) visible in figure 4 (a) and (c). In those case a single large bubble can be seen fragmenting into a large number of smaller bubbles, with many fragmentation events occurring between subsequent frames. One key difference is the resulting distribution of bubbles: in the clean case a few intermediate sized bubbles (around dHd_H) are formed as well as a similar number of sub-Hinze bubbles. In the contaminated case however, a similar number of intermediate sized bubbles are formed, but the number of sub-Hinze bubble is drastically larger.

Different mechanisms may account for the enhanced production of small bubbles in the surfactant-laden case. Surfactants may increase the number of small child bubbles produced during the deformation and breakup of large bubbles in a tearing or shedding like process or during the rupture of elongated individual ligaments. Distinguishing between these mechanisms would require dynamically resolved experiments or simulations focusing on these different scenarios. We comment, however, that our time resolution and the use of a single camera is not sufficient to access detailed dynamics in a reliable way. Our study focuses on the statistical analysis of the influence of surfactant on the fragmentation of a relatively large air cavity in turbulence. Detailed observation of the break-up dynamics would require zoomed in views at higher temporal resolution, with a dedicated experimental setup with multiple cameras such as some past studies (without surfactant) on pinch-off in turbulence (Ruth et al., 2019) or break-up by a single vortex (Qi et al., 2022).

Bubble size distribution

Figure 5 presents the bubble size distribution N(d)\mathcal{N}(d) for the tested solutions: SDS (a), SDS with sea salt (b), CTAB (c), Tween 20 (d) and Tween 20 with sea salt (e) at increasing surfactant concentrations. The dashed lines are shown as references for the −10/3-10/3 scaling in the super-Hinze regime and the −3/2-3/2 scaling in the sub-Hinze regime. The observed transition between these two regimes in the bubble size distribution occurs at d≈2.5d \approx2.5 mm, which is close to the calculated Hinze scale, and will be used as effective Hinze scale dH,effd_{H,\mathrm{eff}}.

Image not extracted

Figure 5. Comparison between the bubble size distributions of different solution composition at varying surfactant concentration. Bubble size distribution for (a) SDS, (b) SDS and sea salt, (c) CTAB, (d) Tween20, (e) Tween 20 and sea salt. Colors indicate the surfactant concentration. Dashed lines indicate the d−3/2d^{-3/2} and d10/3d^{10/3} power laws. The shaded regions represent uncertainties in the distributions, estimated using a Monte Carlo approach, while the solid lines indicate the mean values in the distributions.

For a given set of experiments, the distribution in the super-Hinze scale range (d>dH,effd > d_{H,\mathrm{eff}}) does not change when adding surfactants, and is very similar across the different solutions tested. As the concentration of SDS is increased, with or without sea salt (Figure 5 a and b), the total number of bubbles in the sub-Hinze range increases while that in the super-Hinze regime remains unchanged. The increase in the number of bubbles in the sub-Hinze range is associated with an increase in the slope of the distribution. In contrast, when Tween20 is used (Figure 5 d and e), the bubble size distribution remains unchanged both in the super-Hinze and sub-Hinze ranges. This conclusion is not altered by the presence of sea salt. Using CTAB leads to an intermediate behaviour between that of SDS and Tween 20, where the number of sub-Hinze bubbles increases significantly once the concentration is large enough. Details of the solution (salt, surfactant) only affect sub-Hinze scale bubbles, and the effect is strongly dependent on the type of surfactant used, while the super-Hinze size distribution remains unchanged.

For all conditions, the power law distribution in the sub-Hinze regime at the lowest contamination is compatible with the d−3/2d^{-3/2} distribution due to capillary break-up. For the cases that show a increase in the number of sub-Hinze bubble count, this increase is linked to a steeper distribution as surfactant concentration is increased (i.e. a more negative power law exponent). This modification of the shape of the distribution, together with the fact that we do not observe any changes in the effective Hinze scale when adding surfactant, rules out the possibility that the trends observed in this study are merely a result of increasing the Weber number through a change of the static surface tension.

Counts of Super-Hinze and Sub-Hinze bubbles

We now quantify the increase of sub-Hinze bubbles (Nd<dHN_{d<d_H}) for the various solutions used.

Figure 6(a) shows the counts of super-Hinze bubbles Nd>dHN_{d>d_H} (open triangles) and sub-Hinze bubbles Nd<dHN_{d<d_H} (full squares) as contamination increases (represented by the static surface tension, note the inverted x-axis) for the different types of contamination (colors). We define the reference bubble count, N0N_0, as the bubble count measured in pure water without surfactant or salt. With this definition, the normalized bubble count, N/N0N/N_0, collapses to unity at zero surfactant concentration (corresponding to the maximum static surface tension, γs\gamma_s) for SDS, Tween 20 and CTAB. For surfactant solutions including sea salt, however, the initial normalized counts are slightly greater than unity, possibly due to trace amounts of surfactants present in the sea salt that we use. Figure 6(b) shows the same data as a function of the bulk concentration of surfactant, represented as a fraction of the CMC.

Image not extracted

Figure 6. (a) Variation in the counts of super-Hinze (open triangles) and sub-Hinze (solid squares) bubbles with surface tension. The solid black edge denotes the second realization of SDS experiment. (b) Same data as a function of the bulk concentration of surfactant, represented as a fraction of the CMC.

As contamination increases with the addition of surfactant (surface tension is reduced), the super-Hinze bubble count remains unchanged in all cases (triangles). For sub-Hinze bubbles, all solutions with a fast surfactant (for instance SDS, blue squares) show an increase in counts: for very low surface tensions, the counts of sub-Hinze bubbles are increased a factor 5. In contrast, for cases where surface tension is modified by adding a slow surfactant (Tween 20, green squares), the sub-Hinze bubble counts remain unchanged. The addition of salt is associated with a similar trend: the number of sub-Hinze bubbles increases with increasing SDS concentration (dark blue squares), while remaining essentially unchanged with increasing Tween 20 concentration (dark green squares). The intermediate surfactant (CTAB, yellow squares) exhibits a transitional behaviour: it behaves like a slow surfactant at higher static surface tension γs\gamma_s (low concentration), and increasingly resembles a fast surfactant as γs\gamma_s further decreases (high concentration). In particular, as the CTAB concentration is increased, the sub-Hinze bubble count remains unchanged for γs≳60 mN m−1\gamma_s \gtrsim60\ \mathrm{mN\,m^{-1}}, before increasing as γs\gamma_s is further reduced. The concentration of surfactants required to obtain a similar increase in counts can be vastly different depending the the surfactant used or on whether sea salt is present (Figure 6 b), suggesting a reinforcement of the effect of SDS (anionic) upon the addition of ions. Another way to view the same effect is is the effective reduction of the CMC of charged surfactants in the presence of ions: indeed the CMC of SDS is reduced by almost two orders of magnitude when adding NaCl at seawater concentration ((Schick, 1964; Srinivasan & Blankstein, 2003)), comparable to the differences seen in Figure 6 (b). This effect is also relatively well be captured by plotting the counts as a function of the static surface tension (Figure 6 a).

As stated above, the various cases with Tween 20 show no differences in counts when varying the concentration despite a reduction in surface tension comparable to the reduction when using SDS, highlighting that the increase in the number of sub-Hinze bubbles and the change in the power law observed here is not simply due to a reduction in surface tension and associated increase in Weber number. Tween 20 is non ionic and interactions between the surfactant and sea salt are therefore very limited.

As hinted in the introduction and now demonstrated experimentally, the influence of surfactant on the break-up process is tightly linked to their adsorption time. Surfactants will only affect the breakup process if a significant amount can adsorb to the interface of a bubble between two successive fragmentation events. Indeed, during the stretching preceding fragmentation (through tearing or through the formation of a ligament), a large amount of surface area is created and therefore the surfactant surface concentration on a newly formed bubble is less than the value at equilibrium with the bulk (see sketch in Figure 1 b). If the timescale for adsorption of surfactants to the interface τads\tau_{\mathrm{ads}} is much longer than the typical time between fragmentation events, then after a few breakups, the bubbles will essentially behave as clean bubbles by successive dilutions. We consider here a large scale turbulent time: the eddy turn over time at the integral length scale Teddy(Lint)T_{\mathrm{eddy}}(L_{\mathrm{int}}) (equal to the integral time scale TintT_{\mathrm{int}}) as the representative time for the turbulence break-up sequence to be compared to the adsorption process. To quantify the competition between turbulent transport and adsorption kinetics, we introduce a Biot number ((Tasoglu et al., 2008; Pico et al., 2024)), comparing the turbulence timescale to the adsorption timescale:

Bi=Teddy(Lint)τads.(2)Bi = \frac{T_{\mathrm{eddy}}(L_{\mathrm{int}})}{\tau_{\mathrm{ads}}}. \tag*{(2)}

We therefore need to estimate the adsorption timescale for the various contamination cases considered. The inset of Figure 7 shows data acquired using a maximum bubble pressure tensiometer for SDS (extracted from Fainerman et al. (2010)), Tween 80 (a surfactant similar to Tween 20 but with more oxyethylene groups, extracted from Qazi et al. (2020)) and CTAB (also extracted from Qazi et al. (2020)). The adsorption timescale differs markedly across surfactants, with Tween 80 (∼10\sim10 s) being much slower than SDS (∼10\sim10 ms), while CTAB lies in between (∼1\sim1 s). In all cases, the adsorption timescales become much faster as concentration is increased, with a variation close to τads∝c−2\tau_{\mathrm{ads}} \propto c^{-2}. Note however that the datasets cover concentrations that are larger than the ones we use (highlighted with the shaded areas). We therefore need to extend τads\tau_{\mathrm{ads}} to lower concentrations via modeling.

Image not extracted

Figure 7. Variation in the number of sub-Hinze bubbles as a function of the Biot number BiBi for SDS (blue), CTAB (yellow), and Tween 20 (green). The second SDS realization is denoted with a black edge. Inset: Adsorption time τads\tau_{\mathrm{ads}} as a function of bulk concentration of surfactant in solution. Data points are from the literature, shaded areas represent the ranges used in this study and dashed lines are fits used to extend estimated adsorption times to lower concentrations. Yellow for CTAB (Qazi et al., 2020), blue for SDS (Fainerman et al., 2010) and green for Tween 80 (Qazi et al., 2020).

We follow the approach detailed by Ferri & Stebe (2000): under the assumption that the adsorption is diffusion limited, the adsorption timescale can be expressed as τads∼h2/D\tau_{\mathrm{ads}} \sim h^2/D, where DD is the diffusivity of the surfactant and hh is the depletion depth, the thickness of the layer depleted of surfactants below the interface. This depth is then given by h=Γ/ch = \Gamma/c, with cc the bulk concentration and Γ\Gamma the surface concentration at equilibrium, which is not directly accessible but given by the isotherm (or surfactant equation of state) that the surfactant follows. We make the hypothesis that both surfactants follow a Langmuir isotherm, in which case Γ(c)=Γ∞Kc/(1+Kc)\Gamma(c) = \Gamma_{\infty} Kc/(1 + Kc), with Γ∞\Gamma_{\infty} and KK two constants. Bringing these results together, we obtain finally that the adsorption timescale should follow τads=t0/(1+c/c0)2\tau_{\mathrm{ads}} = t_0/(1 + c/c_0)^2, with t0t_0 and c0c_0 two fitting parameters. This functional form fits well the available literature data, in particular the c−2c^{-2} scaling observed in all datasets (dashed lines). Note however that the approach that we use here is only done to extract a typical adsorption time and has several limitations: first, we have no proof that the adsorption is indeed diffusion limited and that kinetics do not start to play a role for some of the concentrations (although if diffusion is the limiting factor, one expects the c−2c^{-2} scaling observed in the data (Ward & Tordai, 1946)). Second, both datasets were recorded in quiescent conditions, whereas in our case turbulence constantly mixes the fluid and brings surfactant close to the interface. As a consequence, diffusion may be significantly faster than expected (or the depletion depth thinner) and adsorption kinetics may play a role (Chang & Franses, [4]).

We can now plot the normalized count of sub-Hinze bubbles as a function of the Biot number, computed using the fitted adsorption timescale in the inset of Figure 7. As expected, we now very clearly see two different regimes: at low BiBi, the surfactant is too slow for a significant amount to be adsorbed between breakup events and as a consequence the dynamics is identical to the clean case (N/N0≈1N/N_0 \approx1). At higher BiBi however, the number of sub-Hinze bubbles progressively increases as a significant amount of surfactants can adsorb to bubbles before they fragment through a capillary instability, during which important surface tension gradients can then form and influence the resulting size distribution. We note that using another turbulent time would lead to a similar plot, simply shifting the transitional Biot number. With the present choice of the slowest turbulent time, the transition is for BiBi between 0.1 and 1.

Conclusion

Surface active compounds can have a very large impact on bubble breakup in turbulence: they drastically increase the production of sub-Hinze scale bubbles (by up to a factor five) while leaving the number of super-Hinze bubbles unchanged. The size distribution of bubbles is modified with the sub-Hinze range still well described by a power law, but with an exponent increasingly more negative than −3/2-3/2 as the contamination of the solution is increased. This steepening may have important consequences for processes sensitive to the number of small bubbles, e.g air-sea gas exchange or sea salt aerosol production.

However not all surfactants show the effects described above. As demonstrated experimentally, Tween 20, despite reducing the surface tension similarly to SDS, has strictly no effect on the size distribution of bubbles. CTAB exhibits transitional behaviour, with an increase in sub-Hinze bubble production observed only for large concentrations (or when the static surface tension is sufficiently low). This striking difference is due to the slow adsorption of Tween 20 compared with a typical time of deformation of the large bubbles in the turbulent flow, quantified with the Biot number. The addition of ions in the solution reinforces the effects of SDS and a concentration a hundred times smaller can have the same effect on the breakup process as SDS only when artificial sea salt is added, for comparable static surface tension. Tween 20 remains ineffective in modifying sub-Hinze bubble production, even in the presence of ions. Our results therefore demonstrate that static surface tension is not the only parameter to discuss the effects of surfactants on fragmentation. In other interfacial fluid dynamics problems, we highlighted the importance of Marangoni effects and gradients in surface tension that can be characterized by Langmuir trough measurements of isotherms under compression ((Erinin et al., 2023a; Eshima et al., 2025)). Here the measured isotherms for the Tween 20 or SDS solutions are fairly similar (see App. § 5) and a metric based on the Marangoni number alone would not explain the differences in the sub-Hinze bubble production. The common denominator between the problems cited above is that the effects of surfactants could be treated by considering an initially contaminated interface with insoluble surfactants. Because of the solubility of the surfactants considered here, and of the successive fragmentations that bubbles will undergo during the experiment, this approach is not sufficient. It therefore remains an open problem to find the right sets of parameter to fully describe a solution and predict the final size distribution of bubbles. These parameters should take into account the surfactants adsorption time, possible ionic interactions, and the ability for a given surfactant to generate strong Marangoni flows, as well as clarify the detailed mechanism responsible for the increase in small bubbles due to surfactants.

Declaration of Interests The authors report no conflict of interest.

Acknowledgments We thank Emmy Roy who conducted preliminary experiments and Jun Eshima for discussion. We thank the reviewers for their helpful comments.

Funding This work was supported by NSF grant 2242512 to L.D.; the Princeton Catalysis Initiative and the Moore Foundation.

Langmuir trough measurement

For each experimental case, the solution’s surface tension isotherm was measured at the beginning and end of the experiment using a Langmuir trough (KSV NIMA 1003). Specifically, we record the properties of the surface by setting aside a small amount of solution and placing it in the trough, and the surface tension is measured by a force balance with a platinum Wilhelmy plate. Two Teflon barriers compress the surface at a rate of 270 mm/min allowing us to obtain the surface tension γs\gamma_s as a function of the trough area. The resulting data are plotted in Figure 8 as a function of the area, normalized by the area before compression A0A_0.

Image not extracted

Figure 8. Surface tension isotherms of the various solutions used in this study. (a) SDS, (b) SDS and sea salt, (c) CTAB, (d) Tween 20, and (e) Tween 20 and sea salt.

The range of SDS concentrations tested (Figure 8a) spans the full range of interfacial properties, from very clean conditions (flat isotherm at 72 mN m−1^{-1}) to a nearly saturated interface (approximately flat isotherm at ∼40\sim40 mN m−1^{-1}, corresponding to 80% of the CMC). The SDS isotherms with sea salt added (Figure 8b) also cover a broad range of surface tension values, but over a much narrower concentration range (up to 1.2% of the CMC of SDS). The concentrations used with CTAB range up to the CMC and yield static surface tension values range from 72 to less than 40 mN/m. For Tween 20, we use concentrations up to the CMC, yielding a similar range of static surface tension, γs\gamma_s, to that of the SDS cases (Figure 8d). In contrast to SDS, the concentrations required to obtain a low surface tension are similar with and without sea salt.

Time evolution of bubble statistics

Figure 9 shows the temporal evolution of bubble counts N=∫N(d) ddN = \int\mathcal{N}(d)\,\mathrm{d}d over time for all the cases studied. Across all experimental conditions, NN exhibits a sharp increase immediately after the cup is flipped (t=0t = 0), followed by a plateau until the end of the recording. The presence of this plateau shows that number of bubbles entering and leaving the field of view balances out on average. The increased number of sub-Hinze bubbles described in the main text is visible on these graphs.

Image not extracted

Figure 9. The evolution of the bubble number of (a) SDS, (b) SDS and sea salt, (c) CTAB, (d) Tween 20, and (e) Tween 20 and sea salt. The gray area represents the range used to compute the distributions in the rest of the study.

Figure 10 shows the temporal evolution of the cumulative bubble volume V=16π∫d3N(d) ddV = \frac{1}{6}\pi\int d^3\mathcal{N}(d)\,\mathrm{d}d, at every moment for all cases. V0V_0 is the volume of air injected into the cup before the experiment. After the cup is turned around, nearly all the volume is detected. After that the total volume slowly decreases during the experiment due to the larger bubbles getting out of the field view due to buoyancy.

Image not extracted

Figure 10. The evolution of the cumulative bubble volume of (a) SDS, (b) SDS and sea salt, (c) CTAB, (d) Tween 20, and (e) Tween 20 and sea salt. The gray area represents the range used to compute the distributions in the rest of the study. The horizontal dash line represents V=V0V = V_0.

In the main text, we average data over the interval 2.5Tint≤t≤6Tint2.5T_{\mathrm{int}} \le t \le6T_{\mathrm{int}}, this range was chosen as a balance that allows us to obtain sufficiently converged statistics while retaining most of the large scale bubbles. Note that we also verified that the shape of the bubble size distribution does not vary significantly over that window.

References

  1. [1]Bak, A. & Podgórska, W. 2016 Interfacial and surface tensions of toluene/water and air/water systems with nonionic surfactants tween 20 and tween 80. Colloids and Surfaces A: Physicochemical and Engineering Aspects 504, 414–425.DOI
  2. [2]Blaauw, L. J., Lohse, D. & Huisman, S. G. 2025 Salts promote or inhibit bubbly drag reduction in turbulent taylor–couette flows. International Journal of Multiphase Flow 184, 105078.arxiv.org/abs/2411.13196
  3. [3]Cannon, I., Soligo, G. & Rosti, M. E. 2024 Morphology of clean and surfactant-laden droplets in homogeneous isotropic turbulence. Journal of Fluid Mechanics 987, A31.DOI
  4. [4]Chang, C. & Franses, E. I. 1995 Adsorption dynamics of surfactants at the air/water interface: a critical review of mathematical models, data, and mechanisms. Colloids and Surfaces A: Physicochemical and Engineering Aspects 100, 1–45.DOI
  5. [5]Cochran, R. E., Ryder, O. S., Grassian, V. H. & Prather, K. A. 2017 Sea spray aerosol: the chemical link between the oceans, atmosphere, and climate. Accounts of Chemical Research 50 (3), 599–604.DOI

Paper details

vlnc:W_qawed6ye
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 10

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents