betaFeedback

WorksPhysics and Astronomy

Gatemon qubits based on in-situ ternary InAsSb/Al nanowire Josephson junctions

Abstract

Ternary InAsSb/Al nanowires combine compositionally engineerable semiconductor properties with epitaxial proximity superconductivity, making them attractive for hybrid quantum circuits and mesoscopic superconductivity. Here, we realize gatemon qubits based on shadow-defined in-situ InAsSb/Al Josephson junctions in a single growth process. Gate-dependent microwave spectroscopy demonstrates electrostatic tuning of the qubit transition over several gigahertz. Rabi oscillations and Ramsey interference show coherent qubit control, with representative values T1 = 0.79 us and T2* = 0.91 us. Across five gatemons distributed over three chips, the measured relaxation times range from approximately 0.2 us to 1 us and decrease with increasing qubit frequency. Their magnitude is comparable to a circuit estimate of spontaneous emission into the electromagnetic environment. These results establish in-situ InAsSb/Al junctions as coherent, gate-tunable circuit elements and introduce cQED architecture as a microwave probe of the dynamics of the ternary weak link.

Superconducting qubits conventionally employ superconductor–insulator–superconductor (SIS) tunnel junctions as nonlinear circuit elements[1, 2, 3]. A widely used superconducting qubit architecture is the transmon, where the SIS Josephson junction is shunted by a large capacitance[4, 5]. The transmon operates in the regime EJ/EC≫1E_J/E_C \gg1 to exponentially suppress offset-charge sensitivity, where EJE_J is the Josephson energy and ECE_C is the charging energy. The resulted qubit frequency is given by

fq=8EJEC−ECf_q = \sqrt{8E_JE_C} - E_C

A fixed-frequency transmon typically uses a single SIS junction, whereas frequency tunability is commonly achieved by replacing the junction with a superconducting quantum interference device (SQUID). The effective Josephson energy EJ(Φext)E_J(\Phi_{\mathrm{ext}}), and thus the qubit frequency can then be controlled by an external magnetic flux Φext\Phi_{\mathrm{ext}}.

Replacing the insulating tunnel barrier with a semiconductor weak link (S–Sm–S) creates a gatemon, in which an electrostatic gate VgV_g modifies the junction transmission and thereby controls the effective Josephson energy EJ(Vg)E_J(V_g) and qubit frequency[6]. The semiconductor weak link also introduces microscopic degrees of freedom that are absent in a conventional tunnel junction. In particular, the Josephson potential depends on the number and transmission probabilities of the occupied Andreev levels[7], providing a connection between the qubit characteristic and the electronic structure of the weak link. Coherent gatemon operation has been demonstrated in several low-dimensional semiconductor platforms, including hybrid nanowires[8, 9, 10, 11], proximitized two-dimensional electron gases (2DEGs)[12, 13], selective-area-grown superconductor–semiconductor structures[14], Germanium (Ge) heterostructures[15, 16], graphene[17], and carbon nanotubes[18]. Together,

these experiments demonstrate that circuit quantum electrodynamics (cQED) can be extended beyond conventional tunnel junctions to investigate a broad range of hybrid materials and mesoscopic Josephson elements. In this setting, the semiconductor weak link provides an electrostatically tunable Josephson element, while the gatemon provides a sensitive cQED probe of the weak link and its underlying mesoscopic degrees of freedom, besides dissipative DC transport measurements[19, 21, 22, 23].

Ternary InAs1−x_{1-x}Sbx_x nanowires offer an unique materials platform in which the semiconductor properties can be engineered through the Sb fraction xx[24, 25, 26, 32]. At intermediate compositions, InAsx_xSb1−x_{1-x} nanowires have exhibited spin–orbit coupling interaction exceeding that of the binary InAs and InSb endpoint materials, while retaining large gg factor and epitaxial coupling to aluminum (Al) produces a hard induced superconducting gap[24, 25, 26]. Combining alloy composition, electrostatic confinement, and junction geometry creates a broad parameter space for engineering and investigating hybrid electronic states. Embedding such a material platform in a cQED architecture enables fast and high-sensitivity microwave measurements of the junction properties. In the short-junction limit, the Josephson potential of S–Sm–S junction is determined by the transmission probabilities {Ti}\{T_i\} of the occupied channels,

U(ϕ)=−Δ∑i1−Tisin⁡2(ϕ/2)(1)U(\phi)=-\Delta\sum_i\sqrt{1-T_i\sin^2(\phi/2)} \tag*{(1)}

where Δ\Delta is the induced superconducting gap and ϕ\phi is the superconducting phase difference across the junction[7, 22]. Small changes in Josephson potential produces measurable shifts in the qubit frequencies, while microwave pulse sequences provide access to coherent dynamics, relaxation, dephasing, and temporal fluctuations on nanosecond-to-microsecond time scales.

Here, we demonstrate electrical tuning of the qubit transition over a broad frequency range and coherent control of the qubit states. We measure energy relaxation time in five gatemon qubits distributed across three chips and compare the measured lifetime with a simplified spontaneous-emission estimate. Our measurements extend InAsSb/Al junctions from DC transport characterization to coherent cQED operation.

Figure 1 shows the device architecture and the formation mechanism of the nanowire Josephson junction. The gatemon consists of an InAsSb/Al nanowire junction shunted by a large X-shaped capacitor and coupled to a readout resonator, as illustrated in Figure 1(a). The nanowire connects the superconducting island to ground and is capacitively coupled to a local bottom electrostatic gate through an HfOx_x dielectric, as shown in Figure 1(b). Opposite directional InAsSb nanowires were grown from InAs (111)B trenches using MBE system[27, 28, 29]. After the nanowire growth the substrate was cooled down and Al was deposited within the same growth process. During Al deposition, one nanowire acts as a physical shadow mask for the neighboring nanowire, blocking the incident Al flux over a short segment, as shown in Figure 1(c). The resulting uncovered InAsSb segment between the two Al-coated regions forms the S–Sm–S Josephson weak link. After growth, the individual nanowire with the shadow-defined junction is transferred from the growth substrate onto the qubit chip via a micro-manipulator. This shadow-junction technique was previously developed and shown to produce highly transparent Josephson junctions with electrostatically tunable supercurrent[25, 26, 27]. Because the weak link is defined during Al deposition, selective removal of the superconducting shell is not required in the active junction region. Therefore, this technique reduces the post-growth processing applied directly to the weak link and limits its exposure to etchants, residual Al from incomplete shell removal, and possible surface damage[27, 30, 31], as illustrated schematically in Figure 1(d).

Figure 1. Device architecture and formation of the shadow-defined junction. (a) Schematic layout of the capacitively shunted gatemon coupled to a microwave readout resonator. The dashed box indicates the junction region enlarged in panel (b). (b) Electron micrograph of the InAsSb nanowire junction between the superconducting island and ground. The shadow-defined weak link is located above the local gate and separated from it by an atomic-layer-deposited HfOx_x dielectric[27]. (c) Schematic of directional in situ Al deposition. Geometrical shadowing leaves an uncovered semiconductor segment that forms the S–Sm–S weak link. (d) Schematic comparison between etched and shadow-defined junctions. In the etched approach, selective removal of the superconducting shell expose the weak link region to etchants, residual Al, and surface damage. Shadow deposition defines the uncovered semiconductor segment without local shell removal in the active junction region.

We next investigate the microwave response of the InAsSb/Al gatemon. Figure 2 demonstrates electrostatic control of the readout response and qubit spectrum. At each gate voltage VgV_g, we first perform resonator spectroscopy to determine the readout resonator frequency, followed by qubit two-tone spectroscopy to identify qubit transition. Figure 2(a) and (b) show the resonator and qubit spectra as a function of VgV_g, respectively. The data in each panel combine two consecutive gate sweeps acquired over different frequency windows: one from Vg=0V_g=0 to −2-2 V and another from Vg=−2V_g=-2 to −4-4 V. The two-tone spectroscopy reveals a qubit transition that can be tuned over several gigahertz. The transition is observed predominantly at comparatively high frequencies. Within an effective transmon description, this may reflect a relatively large Josephson energy, EJ=Φ0Ic/(2π)E_J=\Phi_0 I_c/(2\pi) where Φ0\Phi_0 is the flux quantum and IcI_c is the critical current. The larger EJE_J is consistent with the high critical currents expected for transparent shadow-defined InAsSb/Al junctions [25, 26, 27]. The transition exhibits a nonmonotonic dependence on VgV_g, as commonly observed in mesoscopic semiconductor Josephson junctions[8, 22, 34]. We further characterize the qubit transition at the gate voltage marked by the dashed line in Figure 2(b). Figure 2(c) shows the two-tone response as a function of drive power and frequency. From the power-dependent spectrum, we identify the fundamental qubit transition fqf_q and the two-photon transition f02/2f_{02}/2. Using α=2(f02/2−fq)\alpha=2(f_{02}/2-f_q), we extract an anharmonicity of α≈−120\alpha\approx-120 MHz. The magnitude of the extracted anharmonicity is substantially smaller than the designed

Figure 2. Gate-dependent microwave spectroscopy of a shadow-junction gatemon. (a) Readout transmission magnitude as a function of readout frequency frf_r and junction-gate voltage VgV_g. (b) Two-tone spectroscopy versus drive frequency fdf_d and VgV_g, showing electrical tuning of the qubit transition. The map combines two measurements with partially overlapping frequency windows; white regions correspond to frequencies that were not measured. The dashed line indicates the gate voltage selected for panel (c). (c) Power-dependent two-tone spectroscopy at Vg=−3.8V_g=-3.8 V, showing broadening of the spectroscopic feature with increasing source power. In all panels, the color scale represents the transmission magnitude after subtraction of the mean response at each gate voltage or source power.

charging energy EC≈204E_C\approx204 MHz, which sets the approximate anharmonicity of a conventional SIS transmon. Such reduced anharmonicity has also been observed in other S–Sm–S gatemons and is consistent with a non-sinusoidal current–phase relation arising from highly transmitting transport channels[22].

Following the electrostatic control of the qubit transition, we next investigate coherent qubit dynamics using pulsed microwave measurements. Figure 3 summarizes the Rabi, energy relaxation and Ramsey measurements performed at a selected operating point. Figure 3(a) shows Rabi oscillation as a function of drive frequency fdf_d and pulse duration τd\tau_d. The oscillation frequency follows fR=fR,02+(fd−fq)2f_R=\sqrt{f_{R,0}^2+(f_d-f_q)^2}, where fR,0f_{R,0} is the resonant Rabi frequency. The resulting chevron demonstrates coherent qubit control and enables calibration of π\pi and π/2\pi/2 pulses. We then measure the energy relaxation time by applying a π\pi pulse and varying the delay time before readout. The representative relaxation trace in Figure 3(b) is fitted to a exponential decay, yielding T1=0.79 μsT_1=0.79\ \mu\mathrm{s}. Finally, we characterize the phase coherence using a Ramsey sequence consisting of two π/2\pi/2 pulses separated by a variable decay. The resulting Ramsey fringes are shown in Figure 3(c). Fitting the data to an exponentially decaying cosine yields T2∗=0.91 μsT_2^*=0.91\ \mu\mathrm{s}. Together, the time-domain measurements demonstrate coherent operation of the InAsSb/Al gatemon.

Figure 3. Coherent control and time-domain characterization of a shadow-junction gatemon. (a) Rabi chevron measured as a function of drive frequency and pulse duration. (b) Representative energy-relaxation measurement. The solid line is a fit to Aexp⁡(−τ/T1)+BA\exp(-\tau/T_1)+B, yielding T1=0.79 μsT_1=0.79\ \mu\mathrm{s}. (c) Ramsey interference measured as a function of the delay between two π/2\pi/2 pulses. The solid line is a fit to an exponentially damped oscillation, yielding T2∗=0.91 μsT_2^*=0.91\ \mu\mathrm{s}.

To assess device-to-device reproducibility, we measure T1T_1 for five gatemons distributed across three chips. Figure 4 shows the relaxation times between approximately 0.2 μs0.2\ \mu\mathrm{s} and 1.0 μs1.0\ \mu\mathrm{s} over the measured qubit-frequency range. The data exhibit an overall decrease in T1T_1 with increasing qubit frequency. The dashed curve shows the spontaneous emission time T1,spontT_{1,\mathrm{spont}} estimated by coupling qubit capacitance Cq=95C_q=95 fF through a coupling capacitor Cc=1.5C_c=1.5 fF to a frequency-independent 50 Ω\Omega environment[33]. The capacitance values are extracted from an Ansys electromagnetic simulation. Its magnitude is comparable to many of the measured values, indicating that spontaneous emission may contribute to relaxation in the present circuit. Because the calculation assumes a frequency-independent 50 Ω\Omega environment, the dashed curve should be interpreted as a circuit estimate rather than a strict upper bound on T1T_1. Spontaneous emission is a circuit-level loss channel rather than an intrinsic limitaion of the semiconductor Josephson junction. Previous work[34, 35] has demonstrated that spontaneous emission can be strongly suppressed through appropriate circuit design and microwave engineering in gatemons. In the present devices, the close proximity of the gate line to the qubit capacitor results in a comparatively large coupling capacitance to the control environment. The measured T1T_1 values therefore characterize the complete circuit architecture and should not be intepreted as the intrinsic coherence limit of the shadow-defined InAsSb/Al junction.

Figure 4. Energy-relaxation times of five shadow-junction gatemon qubits distributed across three chips. Each point shows the fitted relaxation time T1T_1 at a selected qubit frequency fqf_q, with error bars indicating the standard uncertainty obtained from the exponential fit. Colors identify the chips and marker shapes distinguish individual qubits. The dashed curve shows the spontaneous-emission lifetime TspontT_{\mathrm{spont}} estimated for a qubit capacitance Cq=95C_q = 95 fF coupled through Cc=1.5C_c = 1.5 fF to a frequency-independent 50 Ω\Omega environment. Because the effective microwave impedance and coupling capacitance are not independently determined, the curve represents a simplified circuit estimate rather than a strict upper bound.

In conclusion, we have realized and coherently operated gatemons based on shadow-defined ternary InAsSb/Al nanowire Josephson junctions. Gate-dependent spectroscopy demonstrates broad electrical tunability, while the power spectroscopy reveals a reduced anharmonicity consistent with a high-transparency semiconductor weak link. Rabi oscillations and Ramsey interference reveal coherent control. Across five gatemons distributed over three chips, we measure relaxation times at around 1 μ\mus, with an overall decrease toward higher qubit frequencies. The comparable spontaneous-emission estimate suggests that coupling to the electromagnetic environment contributes to relaxation in the present circuit design. These measurements establish shadow-defined InAsSb/Al junctions as electrostatically tunable nonlinear elements for coherent cQED circuits and motivate future designs aimed at suppressing circuit-mediated loss and probing mesoscopic properties of the ternary weak link.

Repeated energy-relaxation measurements

To characterize the temporal variation of the energy-relaxation time, we repeat the T1T_1 measurement 60 times at the same operating point. Each relaxation trace is fitted to an exponential-decay model. The extracted relaxation times are shown in Figure 5. We obtain a mean relaxation time and standard deviation of ⟨T1⟩=0.60(6) μs\langle T_1 \rangle= 0.60(6)\ \mathrm{\mu s}.

Figure 5. Repeated energy-relaxation measurements of an InAsSb/Al gatemon. Each point shows the relaxation time T1T_1 extracted from an independent exponential-decay measurement, with error bars indicating the uncertainty obtained from the fit. The dashed line indicates the mean relaxation time. The 60 measurements yield ⟨T1⟩=0.60(6) μs\langle T_1 \rangle= 0.60(6)\ \mathrm{\mu s}, where the uncertainty denotes the standard deviation of the measured distribution.

Fridge wiring diagram

The devices were measured in a dilution fridge with a base temperature of around 22 mK. The wiring diagram is shown in Figure 6.

Figure 6. Dilution fridge wiring diagram. The qubit drive, readout-in, and TWPA-pump lines are attenuated and thermalized at multiple temperature stages. The DC gate signal is filtered by a low-pass filter and combined with the drive signal through a bias-Tee at the mixing chamber stage. The transmitted readout signal is amplified by a traveling-wave parametric amplifier (TWPA) and a high electron mobility transistor (HEMT) amplifier. The device is mounted in a Qcage at the mixing chamber stage.

Device fabrication

The devices were fabricated on high-resistivity silicon substrates coated with a 100 nm-thick Al film deposited inside the MBE system. The superconducting ground plane, the qubit capacitors, readout resonators, feedline, and control structures were patterned by electron-beam lithography using PMMA A4 resist. After exposure, the resist was developed in a MIBK:IPA 1:3 solution. and the Al film was etched by Transene Aluminum Etchant type D solution. A second e-beam lithography step was used to define the window for the local gate dielectric. An approximately 15 nm-thick HfOx_x layer was subsequently deposited by atomic layer deposition (ALD). The nanowires

were deterministically transferred from the growth substrate onto the qubit chip via a micro-manipulator. Atomic force microscopy (AFM) and fast scanning electron microscopy (SEM) were performed to identify if the nanowires containing shadow-defined junctions and to verify the alignment of each junction with its corresponding bottom gate. For electrical contacting, the devices were coated with a tri-layer resist stack consisting of two MMA EL9 layers and one PMMA A4 layer. After e-beam exposure and development of the contact pattern, in situ Ar ion milling was performed to remove the native oxide from the contact regions. A 400 nm-thick Al layer was then deposited to form galvanic contacts between the nanowires and the superconducting microwave circuit.

Acknowledgments

The authors gratefully acknowledge Smitha Nair for assistance with device fabrication, Peter Krogstrup for supervising the nanowire growth, and András Gyenis for the fruitful discussions. This research was supported by the Novo Nordisk Foundation (grant no. NNF22SA0081175), the NNF Quantum Computing Programme, the Villum Foundation through a Villum Young Investigator grant (grant no. 37467), Innovation Fund Denmark (grant no. 2081-00013B, DanQ), the U.S. Army Research Office (grant no. W911NF-22-1-0042, NHyDTech), the European Union through an ERC Starting Grant (grant no. 101077479, NovADePro), and the Carlsberg Foundation (grant no. CF21-0343). SAK acknowledges funding from Danish Agency for Higher Education and Science, DIANA Quantum Center (DIANAQ), The Danish Chips Competence Center (DKCCC), DIRAC: A national CERN lighthouse initiative, Innovation Fund Denmark (IFD) projects: DeQD, QLIGHT, European Metrology projects: MetSuperQ (Project No. 23FUN08), NoQTeS (Project No. 23NRM04), DINAMO (Project No. 24DIT02). Any opinions, findings, conclusions, or recommendations expressed in this material are those of the authors and do not necessarily reflect the views of the U.S. Army Research Office or the U.S. Government. Views and opinions expressed are those of the authors only and do not necessarily reflect those of the European Union or the European Research Council. Neither the European Union nor the granting authority can be held responsible for them. We thank Lena Jacobsen for program-management support.

References

  1. [1]Y. Nakamura, Y. A. Pashkin, and J. S. Tsai, “Coherent control of macroscopic quantum states in a single-Cooper-pair box,” Nature 398, 786–788 (1999).
  2. [2]P. Krantz, M. Kjaergaard, F. Yan, T. P. Orlando, S. Gustavsson, and W. D. Oliver, “A quantum engineer’s guide to superconducting qubits,” Appl. Phys. Rev. 6, 021318 (2019).DOI
  3. [3]M. Kjaergaard, M. E. Schwartz, J. Braumüller, P. Krantz, J. I.-J. Wang, S. Gustavsson, and W. D. Oliver, “Superconducting qubits: Current state of play,” Annu. Rev. Condens. Matter Phys. 11, 369–395 (2020).
  4. [4]J. Koch, T. M. Yu, J. Gambetta, A. A. Houck, D. I. Schuster, J. Majer, A. Blais, M. H. Devoret, S. M. Girvin, and R. J. Schoelkopf, “Charge-insensitive qubit design derived from the Cooper pair box,” Phys. Rev. A 76, 042319 (2007).DOI
  5. [5]R. Barends, J. Kelly, A. Megrant, D. Sank, E. Jeffrey, Y. Chen, Y. Yin, B. Chiaro, J. Mutus, C. Neill, P. O’Malley, P. Roushan, J. Wenner, T. C. White, A. N. Cleland, and J. M. Martinis, “Coherent Josephson qubit suitable for scalable quantum integrated circuits,” Phys. Rev. Lett. 111, 080502 (2013).DOI
  6. [6]R. Aguado, “A perspective on semiconductor-based superconducting qubits,” Appl. Phys. Lett. 117, 240501 (2020).DOI
  7. [7]C. W. J. Beenakker, “Universal limit of critical-current fluctuations in mesoscopic Josephson junctions,” Phys. Rev. Lett. 67, 3836–3839 (1991).pubmed.ncbi.nlm.nih.gov/10044838
  8. [8]T. W. Larsen, K. D. Petersson, F. Kuemmeth, T. S. Jespersen, P. Krogstrup, J. Nygård, and C. M. Marcus, “Semiconductor-nanowire-based superconducting qubit,” Phys. Rev. Lett. 115, 127001 (2015).DOI
  9. [9]G. de Lange, B. van Heck, A. Bruno, D. J. van Woerkom, A. Geresdi, S. R. Plissard, E. P. A. M. Bakkers, A. R. Akhmerov, and L. DiCarlo, “Realization of microwave quantum circuits using hybrid superconducting-semiconducting nanowire Josephson elements,” Phys. Rev. Lett. 115, 127002 (2015).
  10. [10]L. Casparis, T. W. Larsen, M. S. Olsen, F. Kuemmeth, P. Krogstrup, J. Nygård, K. D. Pettersson, and C. M. Marcus, “Gate-mon benchmarking and two-qubit operations,” Phys. Rev. Lett. 116, 150505 (2016).DOI
  11. [11]T. Ståvenga, S. A. Khan, Y. Liu, P. Krogstrup, and L. DiCarlo, “Lower-temperature fabrication of airbridges by grayscale lithography to increase yield of nanowire transmons in circuit QED quantum processors,” Appl. Phys. Lett. 123, 024004 (2023).DOI
  12. [12]L. Casparis, M. R. Connolly, M. Kjaergaard, et al., “Superconducting gatemon qubit based on a proximitized two-dimensional electron gas,” Nat. Nanotechnol. 13, 915–919 (2018).DOI
  13. [13]W. M. Strickland, L. J. Baker, J. Lee, et al., “Characterizing losses in InAs two-dimensional electron gas-based gatemon qubits,” Phys. Rev. Res. 6, 023094 (2024).arxiv.org/abs/2309.17273
  14. [14]A. Hertel, M. Eichinger, L. O. Andersen, et al., “Gate-tunable transmon using selective-area-grown superconductor-semiconductor hybrid structures on silicon,” Phys. Rev. Applied 18, 034042 (2022).DOI
  15. [15]O. Sagi, A. Crippa, M. Valentini, M. Janik, L. Baghmuyan, G. Fabris, L. Kapoor, F. Hassani, J. Fink, S. Calcaterra, D. Chrastina, G. Isella, and G. Katsaros, “A gate tunable transmon qubit in planar Ge,” Nat. Commun. 15, 6400 (2024).DOI
  16. [16]C. Kiyooka, C. Tangchingchai, L. Noirot, A. Leblanc, B. Brun, S. Zihlmann, R. Maurand, V. Schmitt, E. Dumur, J.-M. Hartmann, F. Lefloch, and S. De Franceschi, “Gatemon qubit on a germanium quantum-well heterostructure,” Nano Lett. 25, 562–568 (2025).DOI
  17. [17]J. I.-J. Wang, D. Rodan-Legrain, L. Brehteau, et al., “Coherent control of a hybrid superconducting circuit made with graphene-based van der Waals heterostructures,” Nat. Nanotechnol. 14, 120–125 (2019).DOI
  18. [18]H. Riechert, S. Annabi, A. Peugeot, H. Duprez, M. Hantute, K. Watanabe, L. Bretheau, T. Taniguchi, E. Arrighi, J. Griesmar, and J.-D. Pillet, “The carbon nanotube gatemon qubit,” Nat. Commun. 16, 7197 (2025).DOI
  19. [19]A. Danilenko, D. Sabonis, G. W. Winkler, O. Erlandsson, P. Krogstrup, and C. M. Marcus, “Few-mode to mesoscopic junctions in gatemon qubits,” Phys. Rev. B 108, L020505 (2023).DOI
  20. [21]A. Kringhøj, T. W. Larsen, O. Erlandsson, W. Uilhoorn, J. G. Kroll, M. Hesselberg, R. P. G. McNeil, P. Krogstrup, L. Casparis, C. M. Marcus, and K. D. Pettersson, “Magnetic-field-compatible superconducting transmon qubit,” Phys. Rev. Applied 15, 054001 (2021).
  21. [22]A. Kringhøj, L. Casparis, M. Hell, T. W. Larsen, F. Kuemmeth, M. Leijnse, K. Flensberg, P. Krogstrup, J. Nygård, K. D. Pettersson, and C. M. Marcus, “Anharmonicity of a gatemon qubit with a few-mode Josephson junction,” Phys. Rev. B 97, 060508(R) (2018).DOI
  22. [23]D. Sabonis, O. Erlandsson, A. Kringhøj, B. van Heck, T. W. Larsen, I. Petkovic, P. Krogstrup, K. D. Pettersson, and C. M. Marcus, “Destructive Little–Parks effect in a full-shell nanowire-based transmon,” Phys. Rev. Lett. 125, 156804 (2020).DOI
  23. [24]J. E. Sestoft, T. Kanne, A. N. Gejl, M. von Soosten, J. S. Yodh, D. Sherman, B. Tarasinski, M. Wimmer, E. Johnson, M. Deng, J. Nygård, T. S. Jespersen, C. M. Marcus, and P. Krogstrup, “Engineering hybrid epitaxial InAsSb/Al nanowires for stronger topological protection,” Phys. Rev. Mater. 2, 044202 (2018).
  24. [25]25 D. J. Carrad, L. Stampfer, D. Olsteins, C. E. N. Petersen, S. A. Khan, P. Krogstrup, and T. S. Jespersen, “Photon-assisted tunneling of high-order multiple Andreev reflections in epitaxial nanowire Josephson junctions,” Nano Lett. 22, 6262–6267 (2022).DOI
  25. [26]26 L. Stampfer, D. J. Carrad, D. Olsteins, C. E. N. Petersen, S. A. Khan, P. Krogstrup, and T. S. Jespersen, “Andreev interference in the surface accumulation layer of half-shell InAsSb/Al hybrid nanowires,” Adv. Mater. 34, 2108878 (2022).DOI
  26. [27]27 S. A. Khan, C. Lampadaris, A. Cui, L. Stampfer, Y. Liu, S. J. Pauka, M. E. Cachaza, E. M. Fiordaliso, J.-H. Kang, S. Korneychuk, T. Mutas, J. E. Sestoft, F. Krizek, R. Tanta, M. C. Cassidy, T. S. Jespersen, and P. Krogstrup, “Highly transparent gatable superconducting shadow junctions,” ACS Nano 14, 14605–14615 (2020).DOI
  27. [28]28 S. A. Khan, L. Stampfer, T. Mutas, J.-H. Kang, P. Krogstrup, and T. S. Jespersen, “Multiterminal quantized conductance in InSb nanoprocesses,” Adv. Mater. 33, 2100078 (2021).arxiv.org/abs/2101.02529
  28. [29]29 S. A. Khan, L. Stampfer, S. Martí-Sánchez, D. Olsteins, D. J. Carrad, T. Jansen, J. Johansson, J. Arbiol, P. Krogstrup, and T. S. Jespersen, “Phase controlled multi-terminal Josephson junction in ternary hybrid nanowire,” arXiv:2511.04719 (2025).
  29. [30]30 Y. Chen, D. van Driel, C. Lampadaris, S. A. Khan, K. Alattallah, L. Zeng, E. Olsson, T. Dvir, P. Krogstrup, and Y. Liu, “Gate-tunable superconductivity in hybrid InSb–Pb nanowires,” Appl.
  30. [31]31 J. E. Sestoft, M. Marnauza, D. Olsteins, T. Kanne, R. D. Schlosser, I.-J. Chen, K. Grove-Rasmussen, and J. Nygård, “Shadowed versus etched superconducting junctions in Al/InAs nanowires,” Nano Lett. 24, 8394–8401 (2024).
  31. [32]32 Q. D. Zhuang, E. A. Anyebe, R. Chen, H. Liu, A. M. Sanchez, M. K. Rajpalke, T. D. Veal, Z. M. Wang, Y. Z. Huang, and H. D. Sun, “Sb-induced phase control of InAsSb nanowires grown by molecular beam epitaxy,” Nano Lett. 15, 1109–1116 (2015).DOI
  32. [33]33 A. A. Houck, J. A. Schreier, B. R. Johnson, J. M. Chow, J. Koch, J. M. Gambetta, D. I. Schuster, L. Frunzio, M. H. Devoret, S. M. Girvin, and R. J. Schoelkopf, “Controlling the spontaneous emission of a superconducting transmon qubit,” Phys. Rev. Lett. 101, 080502 (2008).DOI
  33. [34]34 D. Feldstein-Bofill, Z. Sun, C. Wied, S. Singh, B. D. Isakov, S. Krøjer, J. Hastrup, A. Gyenis, and M. Kjaergaard, “Gatemon qubit revisited for improved reliability and stability,” Phys. Rev. Applied 24, 044099 (2025).
  34. [35]35 Z. Sun, D. Feldstein-Bofill, K. Shagalov, A. T. J. Paulsen, C. Wied, S. Singh, B. D. Isakov, J. Hastrup, C. W. Warren, S. Krøjer, A. Kringhøj, A. Gyenis, and M. Kjaergaard, “Junction-intrinsic dissipation in hybrid superconductor–semiconductor gatemon qubits,” arXiv:2603.29498 (2026).arxiv.org/abs/2603.29498

Paper details

vlnc:W_qeeb5frn
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents