betaFeedback

WorksPhysics and Astronomy

Surfactant amplifies yield-stress effects in the capillary instability of a film coating a tube

Abstract

To assess how the presence of surfactant in lung airways alters the flow of mucus that leads to plug formation and airway closure, we investigate the effect of insoluble surfactant on the instability of a viscoplastic liquid coating the interior of a cylindrical tube. Evolution equations for the layer thickness using thin-film and long-wave approximations are derived that incorporate yield-stress effects and capillary and Marangoni forces. Using numerical simulations and asymptotic analysis of the thin-film system, we quantify how the presence of surfactant slows growth of the Rayleigh-Plateau instability, increases the size of initial perturbation required to trigger instability and decreases the final peak height of the layer. When the surfactant strength is large, the thin-film dynamics coincide with the dynamics of a surfactant-free layer but with time slowed by a factor of four and the capillary Bingham number, a parameter proportional to the yield stress, exactly doubled. By solving the long-wave equations numerically, we quantify how increasing surfactant strength can increase the critical layer thickness for plug formation to occur and delay plugging. The previously established effect of the yield stress in suppressing plug formation [Shemilt et al., J. Fluid Mech., 2022, vol. 944, A22] is shown to be amplified by introducing surfactant. We discuss the implications of these results for understanding the impact of surfactant deficiency and increased mucus yield stress in obstructive lung diseases.

Introduction

Pulmonary surfactant plays a crucial role in the healthy function of the lungs. By lowering surface tension at the interface between air and the liquid that lines lung airways, surfactant helps to prevent unwanted collapse of small airways and alveoli during breathing [36]. Surfactant deficiency is likely to contribute to the increased prevalence of airway obstructions in diseases such as asthma (Hohlfeld 2002) and cystic fibrosis [48]. Mucus, the main component of the airway surface liquid, is a complex fluid exhibiting properties such as viscoelasticity, shear-thinning and a yield stress [26]. In various obstructive diseases, and particularly in cystic fibrosis, the mucus typically has altered rheology, including a significantly increased yield stress compared to mucus in healthy lungs [42]. This provides motivation for this study into the effect of insoluble surfactant on the instability of a viscoplastic liquid coating the interior of a cylindrical tube, which is a simple model for the flow of mucus that can lead to airway closure. Additional applications can be found in related interfacial flows of viscoplastic fluids from engineering and industry, where surfactants may also be present [37, 16, 1].

The instability of a liquid film coating the interior of a cylindrical tube has been widely studied in the case that the liquid is Newtonian. When the volume of fluid in the layer is small, annular liquid collars will form on the tube wall, and when the volume is large enough, liquid plugs form in the tube [14]. Hammond [24] derived an evolution equation for the motion of a thin layer, and presented numerical and late-time asymptotic solutions showing annular collars forming and fluid slowly draining out of thin regions between them. This thin-film theory was then extended to describe the motion of thick films by Gauglitz & Radke [15], who deduced numerically that an approximate minimum thickness of 12% of the tube radius is required for plug formation to occur.

Otis et al. [40] were the first to extend the theory to include the effect of insoluble surfactant at the air-liquid interface. They found that growth of the instability and plug formation is delayed by surfactant. Moreover, if the surfactant is strong then Marangoni forces effectively immobilise the interface, increasing the time scale for the evolution of the layer by a factor of four compared to when there is no surfactant. This factor of four decrease in the growth rate had been previously identified by Carroll & Lucassen [9] in the related instability of a thin liquid layer coating the exterior of a cylindrical filament. Results from the thick-film model of Ogrosky [39] suggest that, whilst this factor is very close to four for layers with thicknesses close to the critical value for plug formation, it may be increased for thicker layers. Halpern & Grotberg [22] investigated the effect of surfactant on the evolution of a layer coating the interior of an elastic tube, and also found slowing of the dynamics and a delay to plug formation, except when the tube stiffness was very low, in which case the impact of including surfactant was minimal. They argued that this slowing implies an increase in the critical thickness required for plug formation, since simulations were run to a fixed finite time. This observation has relevance to mucus plug formation in airways, which typically form within the time scale of a single breath cycle. Experimental results have confirmed the decreased growth rates and increased times for plug formation to occur due to surfactant [10]. Computational fluid dynamics (CFD) simulations have also been conducted which, unlike quasi-one-dimensional models, can capture the post-coalescence phase of plug formation as well as the pre-coalescence phase [43]. It was found, again, that introducing surfactant delayed plug formation, and also that it decreased the stress on the tube wall during plugging. The shear stress exerted on the tube wall is a physiologically important variable in airway closure models as it has been shown that epithelial cell damage can be caused by sufficiently large stresses being exerted on the airway wall [29].

There has been some attention on the effect of non-Newtonian liquid rheology on this flow in the case that there is no surfactant present. Halpern et al. [20] studied the effect of viscoelasticity, showing that the time for a plug to form can be decreased by increasing the Weissenberg number if the layer is sufficiently thick. Romanò et al. [44] also investigated a viscoelastic version of the flow, using CFD, and found that elastic effects can induce a significant peak in the shear stress on the tube wall in the post-coalescence phase of plug formation. Erken et al. [13] took a similar approach but with an elastoviscoplastic model for the liquid layer, showing that elastic effects can also impact how the fluid yields, particularly around and immediately after plug formation.

Shemilt et al. [46] derived reduced-order models to study the effect of viscoplastic rheology on the dynamics of thin films and of thick films in the lead-up to plug formation. It was found that increasing the capillary Bingham number, BB (a parameter proportional to the liquid yield stress), can suppress instability by rigidification of the layer, reduce deformation when there is instability and significantly increase the critical layer thickness required for plug formation to occur. A model describing the evolution of thicker layers was developed using a long-wave approximation, and a simplified evolution equation was deduced using thin-film theory. The viscoplastic long-wave theory used is closely related to the planar thin-film theory exposed by Balmforth & Craster [2]. The structure of the flow is qualitatively the same in long-wave and thin-film theories: where the shear stress exceeds the yield stress the fluid is fully yielded and the flow is shear-dominated, but where the shear stress is less than the yield stress the flow is plug-like with no shear flow at leading order. However, due to changes in the surrounding flow, some regions with plug-like flow must still deform. In these regions, the yield stress is exceeded by an asymptotically small amount [2] and the regions are referred to as ‘pseudo-plugs’ [49]. Whilst the long-wave theory is similar to thin-film theory, it differs in a few crucial ways: the layer is not assumed to be thin relative to the tube radius, additional terms are retained in the evolution equations that more accurately capture the curvature of the geometry, and the exact expression for the curvature of the interface is used instead of the linearised version used in the thin-film theory. Thus, long-wave theory provides a composite approximation to the dynamics of a thick film, which is accurate where the layer is thin and also describes well the regions of the flow that are approximately capillary static. Equivalent, or very similar, approximations have been used previously to study this flow when the liquid layer is viscoelastic [20] or Newtonian [15, 33, 7, 8], including when insoluble surfactant is present [40, 41, 39].

Viscoplastic thin-film theory has been used to describe various other interfacial flows where surface tension plays a key role. Balmforth et al. [3] studied the surface-tension-driven fingering instability in flow down an inclined plane, showing that the yield stress has a stabilising effect. Jalaal & Balmforth [31] developed a model using thin-film theory for a propagating bubble through a tube filled with viscoplastic fluid, which they validated against CFD simulations. Increasing the Bingham number was found to increase the thickness of the film between the bubble and the tube wall. Thin-film theory compared well with simulations for low Bingham numbers but less well when the film thickness increased. Thin-film models for the axisymmetric spreading of droplets [32] and the spreading of long extruded filaments [34] have been developed and used to predict the distances reached by spreading fronts, which decrease as the capillary Bingham number is increased. Whilst these studies all addressed the effect of viscoplastic rheology on capillary phenomena, surfactant effects were not incorporated in any of the models. Craster & Matar [12] used thin-film theory to model surfactant-driven flow in viscoplastic films, demonstrating that after Marangoni forces cause a spreading front to develop, the yield stress can rigidify the layer before it returns to a uniform height profile. This study did not, however, include the effects of capillary forces. To the authors’ knowledge, viscoplastic thin-film theory has not previously been used to study any flows where both capillary and Marangoni forces are present.

In this study, we develop a model for the evolution of a liquid film coating the interior of a tube, where the flow is driven by surface tension but is also influenced by Marangoni forces. Our aim is to quantify the effects of surfactant on the capillary instability and on the previously established effects of the liquid’s yield stress [46]. We will derive evolution equations for the layer height and surfactant concentration using long-wave theory, and subsequently deduce a simpler version of these equations that is valid in the thin-film limit. In order to focus attention on the interaction between Marangoni, capillary and yieldstress effects, other phenomena relevant to airway modelling are not included in the model. The Bingham constitutive model is used, which does not include rheological properties such as shear-thinning, viscoelasticity or thixotropy, but allows us to focus attention on yield-stress effects. Surface tension is assumed to vary linearly with surfactant concentration. For pulmonary surfactants this relation is nonlinear [45], but the linear model captures key Marangoni effects while being amenable to detailed analysis. This choice is in keeping with previous models [22, 39]. Moreover, gravity is assumed negligible, the tube wall is assumed rigid and the air in the centre of the tube is assumed passive. Numerical solutions of both the long-wave and thin-film equations will be used to elucidate the new features of the dynamic evolution that arise due to the presence of surfactant, and also to systematically explore parameter space. We will exploit the relative simplicity of the thin-film equations to study the behaviour of the layer in a late-time limit and in the limit of large Marangoni number (when surfactant is strong). By computing and analysing solutions of the long-wave equations, we will quantify how surfactant alters the dynamics leading to plug formation and the critical thickness required for plugging to occur. In particular, we will show how surfactant acts synergistically with the yield stress to stabilise the liquid layer.

The paper will proceed as follows. In § 2, we derive evolution equations for the layer thickness and surfactant concentration, with the long-wave equations given in § 2.3 and the thin-film equations in § 2.4. Solution methods will then be briefly discussed in § 2.5. Results from the thin-film system will be presented in § 3. An example numerical simulation will be discussed in § 3.1, late-time asymptotic analysis of the thin-film equations will be presented in § 3.2 and the effect of varying the Marangoni number on the stability and evolution of the layer will be systematically addressed in § 3.3. Results for thick films from the long-wave theory will be given in § 4. An example numerical simulation will be examined in § 4.1, a discussion of the behaviour when the Marangoni number is large will be given in § 4.2 and the effect of surfactant on the critical thickness required for plug formation will be explored in § 4.3. Finally, in § 5, there will be a discussion of the significance of the results, particularly in relation to modelling airway closure in the lungs.

Model formulation

Governing equations and boundary conditions

We consider a rigid circular cylindrical tube lined on its interior by a layer of viscoplastic liquid, with a gas in the centre of the tube and insoluble surfactant present at the gasliquid interface (see Figure 1). We assume the system is axisymmetric so it can be described using cylindrical coordinates (r∗,z∗)(r^*,z^*). The tube has radius aa and the interface is located at r∗=R∗(z∗,t∗)r^*=R^*(z^*,t^*). The liquid layer has velocity u∗(r∗,z∗,t∗)=u∗r^+w∗z^\mathbf{u}^*(r^*,z^*,t^*)=u^*\hat{\mathbf{r}}+w^*\hat{\mathbf{z}}, and pressure p∗(r∗,z∗,t∗)p^*(r^*,z^*,t^*) relative to the gas pressure, which is assumed to be spatially uniform.

Image not extracted

Figure 1. Left: sketch of the model geometry. The air-liquid interface is located at r=R(z,t)r = R(z,t). Insoluble surfactant is present at the interface, with (non-dimensionalised) concentration Γ\Gamma. Right: an illustration of a possible axial velocity profile in the liquid layer, ww. Fully yielded, shear-dominated regions (white) are shown adjacent to the interface (R≤r≤Ψ−R \le r \le\Psi_{-}) and adjacent to the wall (Ψ+≤r≤1\Psi_{+} \le r \le1), with a plug-like region (grey) in between (Ψ−<r<Ψ+\Psi_{-} < r < \Psi_{+}).

The liquid is incompressible and we assume inertia is negligible, so conservation of mass and momentum imply

∇∗⋅u∗=0,∇∗⋅τ∗=∇∗p∗(1)\nabla^*\cdot\mathbf{u}^*=0,\qquad\nabla^*\cdot\boldsymbol{\tau}^*=\nabla^*p^* \tag*{(1)}

for R∗≤r∗≤aR^*\le r^*\le a,

where τ∗\boldsymbol{\tau}^* is the deviatoric stress tensor. The boundary conditions at the interface are the kinematic condition,

∂t∗R∗+w∗∂z∗R∗=u∗(2)\partial_t^*R^*+w^*\partial_z^*R^*=u^* \tag*{(2)}

at r∗=R∗r^*=R^*,

and the stress condition,

−p∗n+τ∗⋅n=σ∗κ∗n+∇s∗σ∗(3)-p^*\mathbf{n}+\boldsymbol{\tau}^*\cdot\mathbf{n}=\sigma^*\kappa^*\mathbf{n}+\nabla_s^*\sigma^* \tag*{(3)}

where σ∗\sigma^* is the surface tension, κ∗\kappa^* is the curvature of the interface, n\mathbf{n} is the unit normal to the interface directed away from the liquid layer and ∇s∗\nabla_s^* is the surface gradient operator. At the tube wall, there is no slip and no penetration,

u∗=w∗=0(4)u^*=w^*=0 \tag*{(4)}

at r∗=ar^*=a.

The liquid is assumed to be a Bingham fluid with constitutive relation,

τij∗=(η+τyγ˙∗)γ˙ij∗if τ∗≥τy,γ˙ij∗=0if τ∗<τy(5)\tau_{ij}^*=\left(\eta+\frac{\tau_y}{\dot{\gamma}^*}\right)\dot{\gamma}_{ij}^*\quad\text{if }\tau^*\ge\tau_y, \qquad \dot{\gamma}_{ij}^*=0\quad\text{if }\tau^*<\tau_y \tag*{(5)}

where η\eta is a viscosity, τy\tau_y is the yield stress, γ˙∗=∇∗u∗+∇∗u∗T\dot{\boldsymbol{\gamma}}^*=\nabla^*\mathbf{u}^*+\nabla^*\mathbf{u}^{*T} is the shear-rate tensor, and τ∗\tau^* and γ˙∗\dot{\gamma}^* are the second invariants of τ∗\boldsymbol{\tau}^* and γ˙∗\dot{\boldsymbol{\gamma}}^*, respectively. The second invariant of a tensor T\mathbf{T} is defined as T=12TijTijT=\sqrt{\frac{1}{2}T_{ij}T_{ij}}.

We take the surface tension of the interface to be a linear function of the surfactant concentration,

σ∗=σ0+K(Γ0−Γ∗)(6)\sigma^*=\sigma_0+K(\Gamma_0-\Gamma^*) \tag*{(6)}

where σ0\sigma_0 and Γ0\Gamma_0 represent the constant values of the surface tension and surfactant concentration in an unperturbed state, and K>0K>0 is a constant. We assume that the surfactant is insoluble so its motion is governed by the transport equation (see, e.g., [47])

∂t∗Γ∗+∇s∗⋅(Γ∗us∗)+Γ∗κ∗(u∗⋅n)=0(7)\partial_t^*\Gamma^*+\nabla_s^*\cdot(\Gamma^*\mathbf{u}_s^*)+\Gamma^*\kappa^*(\mathbf{u}^*\cdot\mathbf{n})=0 \tag*{(7)}

where us∗\mathbf{u}_s^* is the velocity along the interface. In (2.7), we have neglected diffusion of surfactant in order to focus on the limit of advection-dominated transport. In lung airways, although there is significant variation in measurements of the properties of surfactant and mucus, we typically expect surfactant diffusivity to be small and that advection will be the dominant transport mechanism ([12, 35, 11]). At the lateral boundaries of the domain, we impose symmetry boundary conditions,

∂z∗R∗=τrz∗=w∗=(us∗⋅z^)Γ=0(8)\partial_z^*R^*=\tau_{rz}^*=w^*=(\mathbf{u}_s^*\cdot\hat{\mathbf{z}})\Gamma=0 \tag*{(8)}

at z∗={0,L∗}z^*=\{0,L^*\}, which enforce that the first derivative of the layer height is zero and that there is no flux of fluid or surfactant across the side boundaries.

Non-dimensionalisation

To non-dimensionalise (2.1)–(7), we introduce the dimensionless quantities,

(r,z)=(r∗a,z∗a),t=σ0aηt∗,γ˙=ηaσ0γ˙∗,(u,w)=ησ0(u∗,w∗),Γ=Γ∗Γ0,τ=aσ0τ∗,R=R∗a,σ=σ∗σ0,p=aσ0p∗,κ=aκ∗,L=L∗a.(9)\begin{aligned} (r,z)&=\left(\frac{r^*}{a},\frac{z^*}{a}\right), \quad t=\frac{\sigma_0}{a\eta}t^*, \quad\dot{\gamma}=\frac{\eta}{a\sigma_0}\dot{\gamma}^*, \quad(u,w)=\frac{\eta}{\sigma_0}(u^*,w^*), \quad\Gamma=\frac{\Gamma^*}{\Gamma_0},\\ \tau&=\frac{a}{\sigma_0}\tau^*, \quad R=\frac{R^*}{a}, \quad\sigma=\frac{\sigma^*}{\sigma_0}, \quad p=\frac{a}{\sigma_0}p^*, \quad\kappa=a\kappa^*, \quad L=\frac{L^*}{a}. \tag*{(9)} \end{aligned}

The mass and momentum conservation equations (2.1) become

0=∂zw+1r∂r(ru),(10)0=\partial_z w+\frac{1}{r}\partial_r(ru), \tag*{(10)}
∂rp=1r∂r(rτrr)+∂zτrz−τθθr,(11)\partial_r p=\frac{1}{r}\partial_r(r\tau_{rr})+\partial_z\tau_{rz}-\frac{\tau_{\theta\theta}}{r}, \tag*{(11)}
∂zp=1r∂r(rτrz)+∂zτzz.(12)\partial_z p=\frac{1}{r}\partial_r(r\tau_{rz})+\partial_z\tau_{zz}. \tag*{(12)}

The wall boundary conditions (4) are

u=w=0onr=1,(13)u=w=0 \quad\text{on}\quad r=1, \tag*{(13)}

the kinematic boundary condition (2) is

∂tR+w∂zR=uonr=R,(14)\partial_t R+w\partial_z R=u \quad\text{on}\quad r=R, \tag*{(14)}

and the stress boundary condition (3) is

References

  1. [1]Ahmadikhamsi, S., Golfier, F., Oltean, C., Lefèvre, E. & Bahrani, S.A. 2020 Impact of surfactant addition on non-newtonian fluid behavior during viscous fingering in hele-shaw cell. Phys. Fluids 32 (1), 012103.DOI
  2. [2]Balmforth, N.J. & Craster, R.V. 1999 A consistent thin-layer theory for Bingham plastics. J. Non-Newton. Fluid Mech. 84 (1), 65–81.DOI
  3. [3]Balmforth, N.J., Ghadge, S. & Myers, T.G. 2007 Surface tension driven fingering of a viscoplastic film. J. Non-Newton. Fluid Mech. 142 (1), 143–149.DOI
  4. [4]Billingham, J. & King, A.C. 2001 Wave Motion. Cambridge University Press.
  5. [5]Camassa, R., Forest, M.G., Lee, L., Ogrosky, H.R. & Olander, J. 2012 Ring waves as a mass transport mechanism in air-driven core-annular flows. Phys. Rev. E 86 (6), 066305.
  6. [6]Camassa, R. & Ogrosky, H.R. 2015 On viscous film flows coating the interior of a tube: thin-film and long-wave models. J. Fluid Mech. 772, 569–599.
  7. [7]Camassa, R., Ogrosky, H.R. & Olander, J. 2014 Viscous film flow coating the interior of a vertical tube. Part 1. Gravity-driven flow. J. Fluid Mech. 745, 682–715.
  8. [8]Camassa, R., Ogrosky, H.R. & Olander, J. 2017 Viscous film-flow coating the interior of a vertical tube. Part 2. Air-driven flow. J. Fluid Mech. 825, 1056–1090.
  9. [9]Carroll, B.J. & Lucassen, J. 1974 Effect of surface dynamics on the process of droplet formation from supported and free liquid cylinders. J. Chem. Soc., Faraday Trans. I 70, 1228–1239.
  10. [10]Cassidy, K. J., Halpern, D., Ressler, B. G. & Grotberg, J. B. 1999 Surfactant effects in model airway closure experiments. J. Appl. Physiol. 87 (1), 415–427.
  11. [11]Chen, Z., Zhong, M., Luo, Y., Deng, L., Hu, Z. & Song, Y. 2019 Determination of rheology and surface tension of airway surface liquid: a review of clinical relevance and measurement techniques. Respir. Res. 20 (1), 274.
  12. [12]Craster, R.V. & Matar, O.K. 2000 Surfactant transport on mucus films. J. Fluid Mech. 425, 235–258.
  13. [13]Erken, O., Fazla, B., Muradoglu, M., Izbassarov, D., Romanò, F. & Grotberg, J.B. 2023 Effects of elastoviscoplastic properties of mucus on airway closure in healthy and pathological conditions. Phys. Rev. Fluids 8, 053102.
  14. [14]Everett, D.H. & Haynes, J.M. 1972 Model studies of capillary condensation. I. Cylindrical pore model with zero contact angle. J. Colloid Interface Sci. 38 (1), 125–137.
  15. [15]Gauglitz, P.A. & Radke, C.J. 1988 An extended evolution equation for liquid film breakup in cylindrical capillaries. Chem. Eng. Sci. 43 (7), 1457–1465.
  16. [16]Glasser, A., Cloutet, É., Hadziioannou, G. & Kellay, H. 2019 Tuning the rheology of conducting polymer inks for various deposition processes. Chem. Mater. 31 (17), 6936–6944.
  17. [17]Griese, M., Essl, R., Schmidt, R., Rietschel, E., Ratjen, F., Ballmann, M. & Paul, K. 2004 Pulmonary surfactant, lung function, and endobronchial inflammation in cystic fibrosis. Am. J. Resp. Crit. Care Med. 170 (9), 1000–1005.
  18. [18]Gunasekara, L. et al. 2017 Pulmonary surfactant dysfunction in pediatric cystic fibrosis: mechanisms and reversal with a lipid-sequestering drug. J. Cyst. Fibros. 16 (5), 565–572.
  19. [19]Halpern, D. & Frenkel, A.L. 2003 Destabilization of a creeping flow by interfacial surfactant: linear theory extended to all wavenumbers. J. Fluid Mech. 485, 191–220.
  20. [20]Halpern, D., Fujioka, H. & Grotberg, J.B. 2010 The effect of viscoelasticity on the stability of a pulmonary airway liquid layer. Phys. Fluids 22 (1), 011901.
  21. [21]Halpern, D. & Grotberg, J.B. 1992 Fluid-elastic instabilities of liquid-lined flexible tubes. J. Fluid Mech. 244, 615–632.
  22. [22]Halpern, D. & Grotberg, J.B. 1993 Surfactant effects on fluid-elastic instabilities of liquid-lined flexible tubes: A model of airway closure. J. Biomech Eng. 115 (3), 271–277.
  23. [23]Halpern, D. & Grotberg, J.B. 2003 Nonlinear saturation of the Rayleigh instability due to oscillatory flow in a liquid-lined tube. J. Fluid Mech. 492, 251–270.
  24. [24]Hammond, P.S. 1983 Nonlinear adjustment of a thin annular film of viscous fluid surrounding a thread of another within a circular cylindrical pipe. J. Fluid Mech. 137, 363–384.
  25. [25]Hewitt, I.J. & Balmforth, N.J. 2012 Viscoplastic lubrication theory with application to bearings and the washboard instability of a planing plate. J. Non-Newton. Fluid Mech. 169-170, 74–90.DOI
  26. [26]Hill, D.B., Button, B., Rubinstein, M. & Hersch, R.C. 2022 Physiology and pathophysiology of human airway mucus. Physiol. Rev. 102 (4), 1757–1836.
  27. [28]Hsia, Connie C.W., Hyde, Dallas M. & Weibel, Ewald R. 2016 Lung structure and the intrinsic challenges of gas exchange. In Comprehensive Physiology, 1st edn. (ed. Ronald Terjung), pp. 827–895. Wiley.
  28. [29]Huh, D., Fujioka, H., Tung, Y., Futai, N., Paine, R., Grotberg, J.B. & Takayama, S. 2007 Acoustically detectable cellular-level lung injury induced by fluid mechanical stresses in microfluidic airway systems. Proc. Natl. Acad. Sci. U.S.A. 104 (48), 18886–18891.
  29. [30]Jalaal, M. 2016 Controlled spreading of complex droplets. PhD thesis, University of British Columbia.DOI
  30. [31]Jalaal, M. & Balmforth, N.J. 2016 Long bubbles in tubes filled with viscoplastic fluid. J. Non-Newton. Fluid Mech. 238, 100–106.
  31. [32]Jalaal, M., Stoeber, B. & Balmforth, N.J. 2021 Spreading of viscoplastic droplets. J. Fluid Mech. 914, A21.DOI
  32. [33]Johnson, M., Kamm, R.D., Ho, L.W., Shapiro, A. & Pedley, T.J. 1991 The nonlinear growth of surface-tension-driven instabilities of a thin annular film. J. Fluid Mech. 233, 141–156.
  33. [34]van der Kolk, J., Tieman, D. & Jalaal, M. 2023 Viscoplastic lines: printing a single filament of yield stress material on a surface. J. Fluid Mech. 958, A34.
  34. [35]Lai, S.K., Wang, Y., Wirtz, D. & Hanes, J. 2009 Micro- and macrorheology of mucus. Adv. Drug Deliv. Rev. 61 (2), 86–100.DOI
  35. [36]Milad, N. & Morrissette, M.C. 2021 Revisiting the role of pulmonary surfactant in chronic inflammatory lung diseases and environmental exposure. Eur. Respir. Rev. 30 (162), 210077.
  36. [37]Mitsoulis, E. 2007 Flows of viscoplastic materials: Models and computations. Rheol. Rev. 135, 135–178.
  37. [38]O’Donnell, A.E., Barker, A.F., Lowite, J.S. & Fick, R.B. 1998 Treatment of idiopathic bronchiectasis with aerosolized recombinant human DNase I. Chest 113 (5), 1329–1334.
  38. [39]Ogrosky, H. R. 2021 Linear stability and nonlinear dynamics in a long-wave model of film flows inside a tube in the presence of surfactant. J. Fluid Mech. 908, A23.
  39. [40]Otis, D.R., Johnson, M., Pedley, T.J. & Kamm, R.D. 1990 The effect of surfactant on liquid film stability in peripheral airways. Adv. Bioeng. 17, 55–57.
  40. [41]Otis, D.R., Johnson, M., Pedley, T.J. & Kamm, R.D. 1993 Role of pulmonary surfactant in airway closure: a computational study. J. Appl. Physiol. 75 (3), 1323–1333.
  41. [42]Patarin, J., Ghiringhelli, É., Darsy, G., Obamba, M., Bochu, P. & de Saint Vincent, M.R. 2020 Rheological analysis of sputum from patients with chronic bronchial diseases. Sci. Rep. 10, 15865.
  42. [43]Romanò, F., Muradoglu, M. & Grotberg, J. B. 2022 Effect of surfactant in an airway closure model. Phys. Rev. Fluids 7, 093103.
  43. [44]Romanò, F., Muradoglu, M., Fujioka, H. & Grotberg, J.B. 2021 The effect of viscoelasticity in an airway closure model. J. Fluid Mech. 913, A31.
  44. [45]Schürch, S., Bachofen, H. & Possmayer, F. 2001 Surface activity in situ, in vivo, and in the captive bubble surfactometer. Comp. Biochem. Physiol. Part A Mol. Integr. Physiol. 129 (1), 195–207.
  45. [46]Shemilt, J.D., Horsley, A., Jensen, O.E., Thompson, A.B. & Whitfield, C.A. 2022 Surface-tension-driven evolution of a viscoplastic liquid coating the interior of a cylindrical tube. J. Fluid Mech. 944, A22.
  46. [47]Stone, H.A. 1990 A simple derivation of the time-dependent convective-diffusion equation for surfactant transport along a deforming interface. Phys. Fluids A 2 (1), 111–112.
  47. [48]Tiddens, H.A.W.M., Donaldson, S.H., Rosenfeld, M. & Paré, P.D. 2010 Cystic fibrosis lung disease starts in the small airways: can we treat it more effectively? Pediatr. Pulmonol. 45 (2), 107–117.
  48. [49]Walton, I.C. & Bittleston, S.H. 1991 The axial flow of a Bingham plastic in a narrow eccentric annulus. J. Fluid Mech. 222, 39–60.

Paper details

vlnc:W_qjtza2x9
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents