betaFeedback

WorksPhysics and Astronomy

A tunable multi-gated platform for superlattice engineering in bilayer graphene

Abstract

Periodic potentials with length scales much larger than crystal lattice constants can generate low-energy electronic minibands. While small-angle twisted van der Waals heterostructures have been widely used to realize such physics, correlated phases are often limited by twist-angle inhomogeneity, strain, and disorder. Here, we investigate high-quality Bernal bilayer graphene placed on a patterned graphite gate, featuring a triangular array of holes, forming a new class of "gate-engineered" superlattices tunable through three independent electrostatic gates. Near the charge neutrality point, we observe insulating states characteristic of miniband formation. Temperature-dependent transport reveals activated gaps consistent with theory, and Hall measurements indicate charge-carrier inversion. Notably, the superlattice can be reconfigured electrostatically using various gate combinations, enabling flexible band-structure design without mechanical twisting. The results highlight a new route to band engineering, potentially extendable to complex periodic structures that are untenable in natural materials.

The discovery of strong correlations in flat bands of magic-angle twisted bilayer graphene [1, 2, 3] has driven the search for alternative systems with similar physics but fewer fabrication challenges [1, 4, 5, 6, 7]. While moiré materials are rapidly expanding through advanced stacking techniques, twist-angle control remains a major bottleneck − introducing inhomogeneity, strain, and disorder that cause large sample-to-sample variations [8, 9, 10, 11]. Even devices with nominally identical twist angles can show vastly different properties. The quest for robust correlated physics has therefore led to explorations of alternate material platforms that host flatter bands, such as Bernal bilayer graphene (BLG) [12] and rhombohedral multilayer graphene [13, 14]. However, such samples are difficult to fabricate, demanding high levels of purity. In contrast, a distinct engineering approach would be to impose a smoothly varying electrostatic potential on a conventional two dimensional (2D) material such as graphene over length scales larger than its lattice constant, mimicking the moiré potential. This results in an effective superlattice with an enlarged real-space periodicity and a reduced Brillouin zone. Although implementing such artificial lattices in 2D materials remains experimentally challenging, recent advances have demonstrated promising strategies [15, 16, 17, 18, 19, 20, 21].

For a triangular superlattice with lattice constant λs\lambda_s, the carrier density needed to fill each four-fold spin-valley degenerate miniband is given by ns=83λs2n_s = \frac{8}{\sqrt{3}\lambda_s^2}. Experimental carrier densities are typically limited to ∼1012−1013/cm2\sim10^{12} - 10^{13}/\mathrm{cm}^2, which requires superlattice periods of the order of tens of nanometers for the minibands to be experimentally accessible. Recent studies have explored two distinct approaches to enable this: dielectric patterning [16, 17] and the moiré proximity effect [22, 23, 24]. The former involves patterning the bottom dielectric, typically SiO2_2 [16], into a lattice of choice (triangular, one-dimensional, or square), thereby inducing resistance peaks, attributed to electron-hole miniband formation. Another approach is to use an external moiré material (such as twisted hBN or transition metal dichalcogenides) in close proximity to a target 2D layer, and open observable superlattice gaps [22, 24]. Despite their promise, both dielectric patterning and moiré-induced potentials face challenges: the former is limited by dielectric contrast and resolution, while the latter is highly sensitive to twist-angle disorder, limiting reproducibility and control.

In this work, we present gate engineering as an innovative approach to realize a robust and tunable superlattice potential in BLG, enabling programmable band structures with tailored functionalities [25]. Figure 1a shows the schematic of our hBN-encapsulated BLG device controlled by three independent gates: a top gate (TG), a patterned graphite superlattice gate (SL), and a global Si bottom gate (BG). While dual-gated BLG devices are well established for independent control of carrier density and displacement field, our device incorporates an artificially patterned graphite gate between BLG and the Si BG. The SEM image (Figure 1a, top left) shows holes etched in graphite forming a triangular lattice with a period of 50 nm. A patterned gate enables direct electrostatic modulation of carrier density across the entire sample area. Moreover, the combination of the holey SL gate and global BG allows independent control of displacement fields in holey and non-holey regions. BLG is chosen for its tunable band gap via displacement fields and its rich correlated and topological phases near the band edge [12, 26, 27, 28]. Recent theoretical investigations also highlight the promising emergence of topological and correlated phases in BLG through superlattice potential modulation [25, 29].

Schematic of the triple-gated device and folded band structures of BLG

Figure 1. Gate engineering and modifications in the band structure of BLG. (a) Schematic of the triple-gated device consisting of hBN encapsulated Bernal BLG, where VTGV_{\mathrm{TG}}, VSLV_{\mathrm{SL}}, and VBGV_{\mathrm{BG}} are the voltages applied to the top, superlattice, and Si bottom gate, respectively. The top left panel shows a false-colored scanning electron microscope image of the patterned graphite layer with a scale bar of 50 nm. The inset shows optical image of device D1 consisting of two distinct regions of SL gate (green) and plain gate (blue). The scale bar is 5 μ\mum. (b)–(d) Folded band structure of BLG at VSL=0V_{\mathrm{SL}} = 0 V, 3 V, and 5 V along the high symmetry path ΓS−MS−KS−ΓS\Gamma_{\mathrm{S}} - M_{\mathrm{S}} - K_{\mathrm{S}} - \Gamma_{\mathrm{S}} of the superlattice Brillouin zone.

In the absence of a superlattice gate voltage (VSL=0V_{\mathrm{SL}} = 0 V), BLG exhibits the characteristic parabolic dispersion near the CNP, with conduction and valence bands touching at the K point (ΓS\Gamma_{\mathrm{S}} of the superlattice Brillouin zone) and preserving electron–hole symmetry, resulting in gapless semimetallic behavior (Figure 1b). Applying a periodic electric field via the uniform TG and patterned SL drastically modifies the band structure. As VSLV_{\mathrm{SL}} increases (Figure 1c–Figure 1d), (i) a gap opens at the CNP, (ii) the bands flatten near high-symmetry points (MSM_{\mathrm{S}}, KSK_{\mathrm{S}}), indicating reduced group velocity and enhanced density of states, (iii) minibands and avoided crossings emerge with energy shifts, and (iv) reversing VSLV_{\mathrm{SL}} interchanges conduction and valence bands, producing pronounced particle–hole asymmetry. This asymmetry, absent in pristine BLG, originates from the asymmetric coupling of the periodic potential and demonstrates enhanced tunability compared to uniformly gated BLG.

Our devices consist of two functionally distinct regions: one with a plain graphite gate and another with a patterned superlattice graphite gate, enabling a direct comparison of the effect of the superlattice potential (see the optical image of a typical device in Figure 1a). Our primary measurements are performed on device D1 with a superlattice periodicity of 50 nm, at T=1.8T = 1.8 K, except for the temperature-dependent data. The devices exhibit high mobility of 22–3×1053 \times10^{5} cm2^{2}V−1^{-1}s−1^{-1} (see Supplementary Material Fig. S2). First, we present data for BLG with the plain gate, which produces a uniform electric field in the 2D plane. In Figure 2a, we plot the longitudinal resistance RxxR_{xx} as a function of VTG−VDV_{\mathrm{TG}} - V_{\mathrm{D}} at VG=0V_{\mathrm{G}} = 0 V, where VTGV_{\mathrm{TG}} is the top-gate voltage, VDV_{\mathrm{D}} corresponds to the CNP offset, and VGV_{\mathrm{G}} is the plain graphite gate voltage. As expected, when a finite displacement field DD is applied, an increase in RxxR_{xx} (Figure 2b) at CNP is observed due to band gap opening. We now present the primary data obtained by applying a finite VSLV_{\mathrm{SL}}. Figure 2c shows RxxR_{xx} as a function of negative VTGV_{\mathrm{TG}} at VSL=4V_{\mathrm{SL}} = 4 V. In contrast to standard BLG, which exhibits a single resistance peak, multiple peaks are clearly observed.

Effect of superlattice gate on electrical transport

Figure 2. Effect of superlattice gate on electrical transport. (a) Four-probe longitudinal resistance RxxR_{xx} for device D1, as a function of VTG−VDV_{TG}-V_D at plain graphite gate voltage VGr=0V_{Gr}=0 V, where VDV_D is the offset in the CNP due to residual charge carriers. (b) Color plot of RxxR_{xx} as a function of VTGV_{TG} and VGrV_{Gr} shows the magnitude of RxxR_{xx} increases at the CNP. (c) Line plot of RxxR_{xx} vs. VTGV_{TG} at VSL=4V_{SL}=4 V shows multiple peaks. (d) The contour map of RxxR_{xx} vs. VTGV_{TG} at different VSLV_{SL} shows the evolution of these peaks. (e)-(f) Line plot of RxxR_{xx} vs. VTGV_{TG} at VSL=−4V_{SL}=-4 V and the contour plot show similar behaviour as panel c.-d. (g),(i) Resistivity calculated theoretically across the bands is plotted for positive VSLV_{SL} values. (h),(j) Experimentally obtained RxxR_{xx} in the same range. A qualitative comparison of the data reveals good agreement between theory and experiment, indicating the emergence of additional miniband features. In panel (h), the resistance peak around zero density (VTG−VD=0V_{TG}-V_D=0) is marked as IS1IS1, while the secondary peaks are marked as IS2IS2 and IS3IS3, respectively.

To track the evolution of these features, we performed dual-gate sweeps. Figure 2d shows a contour plot of RxxR_{xx} obtained by continuously sweeping VTGV_{\mathrm{TG}} at discrete VSLV_{\mathrm{SL}}. Similar to the standard BLG data in Figure 2b, all the resistance peaks shift diagonally with gate voltages. Near VSL=0V_{\mathrm{SL}} = 0 V, a single resistance peak is recovered, consistent with plain-gated BLG. Strikingly, as VSLV_{\mathrm{SL}} increases, two distinct peaks emerge at intermediate voltages (dark red bands in Figure 2d), followed by the appearance of a third peak at higher VSLV_{\mathrm{SL}}. Moreover, the magnitude of RxxR_{xx} increases with increasing VSLV_{\mathrm{SL}}. Similar features are observed when the polarities of both gates are reversed (Figure 2e–Figure 2f), although the magnitude of resistive peaks differs slightly. For clarity, we label the resistance peak at VSL=0V_{\mathrm{SL}} = 0 V, corresponding to the CNP gap, as IS1IS1. For VSL>0V_{\mathrm{SL}} > 0 V, the secondary peaks are labeled IS2IS2 (hole side, left), appearing at low/intermediate VSLV_{\mathrm{SL}}, and IS3IS3 (electron side, right), appearing at higher VSLV_{\mathrm{SL}} (Figure 2h, Figure 2j). Intriguingly, the secondary peak due to the band gap opening on the electron (hole) side is weaker for positive (negative) VSLV_{\mathrm{SL}} values, hinting at electron-hole asymmetries that are in agreement with those seen in the bandstructure calculations (see Supplementary Material Fig. S27). Consequently, for VSL<0V_{\mathrm{SL}} < 0 V, the secondary peaks appear at mirrored positions (see Supplementary Material Fig. S6). The emergence of multiple resistive peaks marks a clear departure from the conventional BLG behaviour. Their appearance point to the emergence of multiple minibands separated by gaps in the band structure, as expected from theoretical calculations discussed earlier. To probe the robustness of these states and their dependence on the electric field, we varied the gate-sweep configuration. Supplementary Material Fig. S4 shows RxxR_{xx} measured by sweeping VSLV_{\mathrm{SL}} continuously at device VTGV_{\mathrm{TG}}. Consistent with Figure 2c–Figure 2d, three resistance peaks appear for both polarities of the gate voltages, validating that the underlying mechanism is governed by the periodic electric field generated by the combined action of the two gates. In both cases, the separation between the two dominant resistance peaks increases with the displacement field, suggesting that the bands shift as VSLV_{SL} increases.

For a more direct comparison between experiment and theory, we calculated the longitudinal conductivity within the constant-relaxation-time approximation,

Gxx∝∫d2k(2π)2vx2(−∂f0∂E),G_{xx} \propto\int\frac{d^{2}k}{(2\pi)^{2}}v_x^{2}\left(-\frac{\partial f_0}{\partial E}\right),

where vxv_x is the xx-component of the carrier velocity and f0f_0 is the Fermi–Dirac distribution. The electrostatically tuned band structures obtained from the model were used as input to this calculation. Importantly, both the band dispersion and the chemical potential evolve simultaneously as VTGV_{TG} and VSLV_{SL} are varied; hence, they were self-consistently updated for each pair (VTG,VSL)(V_{TG}, V_{SL}) (see Supplemental Material Section II B for details). The resulting resistance maps, Rxx∝1/GxxR_{xx} \propto1/G_{xx} (Figure 2g, 2i), capture the salient features of

the experimental data (Figure 2h, 2j)—notably the emergence of multiple gap regions separated by conducting minibands and a clear particle–hole asymmetry. In addition, we find that the first gap above the CNP is significantly smaller than the first gap below the CNP (Figure 1c-Figure 1d). The smaller resistive peak observed for IS3IS3 on the electron side, compared to IS2IS2 on the hole side, is a direct consequence of this asymmetry.

While a precise quantitative correspondence is limited by the sensitivity of the band structure to microscopic model parameters (see Supplemental Material Section II C), the principal qualitative features exhibit excellent agreement between theory and experiment. We also highlight that the reported resistance - gate voltage maps are distinct from those previously reported for moiré materials [30, 31, 32]. Here, the highly resistive miniband features exhibit dispersive behavior in the gate voltage phase space (see Figure 2h and Figure 2j), governed by both VTGV_{TG} and VSLV_{SL}. In contrast, in moiré systems [30], the position of superlattice gaps is solely governed by the twist angle and remains unaffected by electric fields.

To gain further insights into the transport properties of the system, we perform temperature-dependent transport measurements which provide another powerful approach to probe the nature of ground states, whether metallic, semiconducting, or insulating. We therefore measured RxxR_{xx} over a range of temperatures TT to estimate the corresponding energy gaps. As discussed earlier, the increasing trend of RxxR_{xx} with VSLV_{SL} indicates the opening of a gap at the CNP in BLG. Figure 3a-Figure 3b show RxxR_{xx} versus VSLV_{SL} for two different values of VTGV_{TG} (±4.6\pm4.6 V) across temperatures from 7.5 K to 100 K. At low temperatures (T≤30T \le30 K), RxxR_{xx} remains nearly constant, whereas at higher temperatures it decreases, consistent with the insulating nature of these states. Similar behaviour is observed when varying VTGV_{TG} continuously at constant VSLV_{SL} (see Supplemental Material Figure S7-8).

Estimation of energy gaps

Figure 3. Estimation of energy gaps. (a)-(b) Temperature TT dependence of RxxR_{xx} vs. VSLV_{SL} at VTG=±4.6V_{TG} = \pm4.6 V. The insulating states persist up to approximately T=100T = 100 K. (c)-(d) Thermally activated gaps Δ\Delta estimated for IS1IS1 and IS2IS2 are plotted as a function of VSLV_{SL}. (e) Hall density nH=−1/e(B/Rxy)n_H = -1/e(B/R_{xy}), where RxyR_{xy} is Hall resistance BB is the magnetic field, and ee is the charge of an electron is plotted as a function of VTGV_{TG} at VSL=5V_{SL} = 5 V and B=5B = 5 T. The prominent sign changes observed in nHn_H (red circles) are consistent with the position of the peaks IS1IS1 and IS2IS2 in RxxR_{xx} (blue trace), denoted by top arrows. An additional Lifshitz transition-like signature is observed in both RxxR_{xx} and RxyR_{xy}, indicated by the dotted line. All the data presented are for device D1.

Temperature dependence of $R_{xx}$ at different $V_{SL}$

Figure S7. Temperature dependence of RxxR_{xx} at different VSLV_{SL}. a. RxxR_{xx} as a function of VTGV_{TG} at VSL=−2V_{SL}=-2 V taken for different temperatures TT ranging from 7.5 K to 115 K. b. VSL=−3V_{SL}=-3 V up to T=140T=140 K c. VSL=−4V_{SL}=-4 V. d. VSL=−5V_{SL}=-5 V. The blue and black arrows denote two insulating states IS1IS1 and IS2IS2 as defined in the text. Data for device D1.

To estimate the energy gap, we plot the peak values of RxxR_{xx} as a function of 1/T1/T. Prior studies have shown that at low temperatures (T≤30T \le30 K, in our case), the peak resistance exhibits only a weak dependence on 1/T1/T, consistent with variable-range hopping (VRH) or a combination of VRH and nearest-neighbour hopping at low and intermediate TT [33, 34]. At higher temperatures (T≥60T \ge60 K), however, RxxR_{xx} shows thermally activated behaviour,

following: Rxx∝exp⁡(Δ/2kBT)R_{xx} \propto\exp(\Delta/2k_BT), where Δ\Delta is the energy gap and kBk_B is the Boltzmann constant. Fitting this relation to the RxxR_{xx} versus 1/T1/T data allows us to extract Δ\Delta (see Supplemental Material Figure S8). To determine Δ\Delta at different VSLV_{SL}, we performed temperature-dependent RxxR_{xx} versus VTGV_{TG} measurements across multiple VSLV_{SL} values. Figure 3c-Figure 3d shows Δ\Delta as a function of VSL<0V_{SL} < 0 V for IS1IS1 and IS2IS2. For IS1IS1, Δ\Delta initially increases with VSLV_{SL}, saturating for higher values. By contrast, IS2IS2, which emerges around VSL=−3.6V_{SL} = -3.6 V, shows only a weak dependence of Δ\Delta on VSLV_{SL}. These observations deviate from the conventional behaviour of gapped BLG, where Δ\Delta typically increases linearly with the displacement field [35]. Nonetheless, the magnitudes of Δ\Delta for both the peaks IS1IS1 and IS2IS2 are in order-of-magnitude agreement with our theoretical calculations (see Figure 1c-Figure 1d). However, the third peak IS3IS3 was much weaker, and was therefore not ideal for the quantitative temperature dependent study. We note that although fitting the Arrhenius equation is a standard method for extracting energy gaps in thermally activated transport, the extracted values are highly sensitive to the temperature range used for the fit (see Supplemental Figure S10). Even small variations in the chosen TT window can yield significantly different Δ\Delta. Therefore, transport measurements alone cannot provide a highly accurate estimate of the gap. In our analysis, we selected the fitting range that yields the least error in the higher-temperature regime (see Supplemental Material Section I B for details).

Fitting Arrhenius equation for thermally activated behavior

Figure S8. Fitting Arrhenius equation for thermally activated behavior. a.-b. The maximum resistance of IS1IS1, indicated by the blue arrow, is plotted as a function of 1/T1/T. The Arrhenius equation Rxx=R0exp⁡(Δ/2kBT)R_{xx}=R_0\exp(\Delta/2k_{\mathrm{B}}T) is fitted for the high TT range that means lower values of 1/T1/T. The slope of these red dashed lines is Δ/2kB\Delta/2k_{\mathrm{B}}. c.-d. Similar fitting done for the state IS2IS2. Data for device D1.

Sensitivity of the extracted activation gap to the fitting range

Figure S10. Sensitivity of the extracted activation gap to the fitting range. a.-c. Arrhenius plots of Rxxmax⁡R_{xx}^{\max} for different temperature fitting ranges at VTG=−4.6V_{TG}=-4.6 V. The extracted activation gap varies by approximately 10 meV when the lower bound of the fitting temperature range is shifted by 10 K.

Next, we present magnetotransport measurements. In particular, measurement of the Hall resistance RxyR_{xy} can reveal signatures of charge carrier type, Fermi surface reconstructions and large density of states within minibands [36, 37, 38, 39]. Figure 3e shows RxxR_{xx} and the Hall density nH=−1eBRxyn_H = -\frac{1}{e}\frac{B}{R_{xy}} as a function of VTGV_{TG} at VSL=5V_{SL} = 5 V and a magnetic field B=5B = 5 T. We observe clear sign changes in nHn_H at the peak positions corresponding to IS1IS1 and IS2IS2, indicated by vertical arrows (blue and black), signifying a direct correlation between longitudinal and transverse transport signatures. Sign changes in nHn_H can occur when the Fermi energy EFE_F reaches a band gap, where the band transitions take place and/or a van Hove singularity, where Lifshitz transitions may take place [36, 37]. The highly resistive peaks in RxxR_{xx} in concurrence with the nature of sign changes in nHn_H validates the presence of multiple energy gaps. We observe the emergence of an additional tiny peak in RxxR_{xx} (see Supplemental Material Figure S3) and a corresponding sign change in nHn_H, indicated by the orange arrow. This additional peak along with the sign change in nHn_H may be a correlation-induced phenomena, consistent with the high density of states in the minibands [36, 37, 38, 39]. Taken together, the Hall responses align with the formation of minibands characterized by sizable band gaps and an enhanced density of states.

Effect of superlattice gate voltage

Figure S3. Effect of superlattice gate voltage a. Color map of RxxR_{xx} as a function of top-gate voltage VTGV_{\mathrm{TG}} and superlattice gate voltage VSLV_{\mathrm{SL}}. b. Horizontal line cuts extracted from (a). At VSL>3V_{\mathrm{SL}} > 3 V, a tiny peak emerges between two prominent peaks, as indicated by the black arrow.

Finally, we demonstrate the multi-functionality of the periodic potential by systematically tuning different gate combinations in our device. While our measurements thus far have relied on two gates VSLV_{SL} and VTGV_{TG}, our device architecture provides a third knob, namely, the bottom Si gate (VBGV_{BG}), enabling multiple gate configurations to tailor the effective superlattice potential. For instance, while the potential along the non-holey regions is governed by the voltage applied to the graphite SL gate, the potential along the holey regions can be independently tuned via the Si BG (see Supplemental Material Fig. S17). This design allows selective and continuous modulation of the SL potential strength in BLG, introducing a new degree of control that was not achievable in earlier superlattice-based studies [16, 17, 18, 20].

In the following, we demonstrate three configurations to illustrate the multi-gate tunability, as schematically described in Figure 4a-Figure 4c (see Supplemental Material Section I F for additional data and discussion.). We first demonstrate a new configuration using the gates VBGV_{BG} and VSLV_{SL}, with VTG=0V_{TG}=0 (see Figure 4a). Line traces of RxxR_{xx} at different VBGV_{BG} reveal two distinct peaks emerging at finite VBGV_{BG} (see Figure 4d). This finite VBGV_{BG} gives rise to a secondary peak, consistent with the features described in Figure 2–Figure 3 (see Supplemental Material Fig. S22-24 for device D3). For the second and third configurations, we examined two additional devices, D2 and D3, respectively. In Figure 4b, the Si BG is used to induce a periodic potential in the BLG, with the graphite SL gate serving solely as a screening layer. This configuration can be approximated as a negative image of the potential profile generated by the graphite SL alone (see Supplemental Material Fig. S13). We find a secondary peak by increasing VBGV_{BG}, as shown in Figure 4e. Finally, in Figure 4c, we demonstrate simultaneous operation of all three gates. The line plots show RxxR_{xx} vs. VTG−VDV_{TG}-V_D for several values of VSLV_{SL} in the presence of a finite VBGV_{BG} (Figure 4f). A clear trend emerges—increasing VSLV_{SL} leads to the emergence of a secondary peak. To isolate the role of VBGV_{BG}, we additionally show data taken while varying VBGV_{BG} at fixed VSLV_{SL} (Figure 4i). The system exhibits only a single peak at the CNP for low VBGV_{BG}, whereas a pronounced secondary peak appears at VBG=70V_{BG}=70 V—underscoring that the superlattice effect is substantially reinforced in the presence of a third gate. In Figure 4g-Figure 4h, we present the magnetotransport data in device D2. When VBGV_{BG} is finite, the system exhibits new states, manifested as additional resistance peaks in RxxR_{xx} (Figure 4e) similar to the other configurations highlighting the versatility of gate engineering. Interestingly, this configuration also revealed new states in the presence of magnetic fields. Figure 4g shows a color map of RxxR_{xx} as a function of VBGV_{BG} and VTGV_{TG}, at B=8B=8 T, where Landau levels appear as minima. Surprisingly, two new minima emerge at higher VBGV_{BG}, which are absent at lower VBGV_{BG} values, indicated by blue arrows in the colour plot. Figure 4h shows line traces of RxxR_{xx} at VBG=20V_{BG}=20 V and 40 V, where it is clear that the minima are better resolved at 40 V. These results suggest that quantum Hall states can also be manipulated by the multi-gate architecture. However, whether these new states arise from spin/valley symmetry breaking at finite VBGV_{BG}, or result from higher minibands, remains unclear and warrants further investigation. These results establish a realistic pathway for future investigations of higher-order topological bands, and fractional Chern insulators in artificially engineered architectures, where the three-gate electrostatic platform may enable independent tuning of the carrier density, displacement field, and superlattice potential [25]. A straightforward next step would be to implement this architecture with an enhanced periodic potential, achievable by reducing the hBN spacer thickness, and with a shorter superlattice periodicity comparable to that of twisted bilayer graphene-moiré lattices.

Demonstration of multi-gate tunability with three gate configurations and resistance traces

Figure 4. Demonstration of multi-gate tunability. (a-c) Three different gate combinations used for devices D1, D2 and D3, respectively, that highlights the versatility of the multi-gated platform. (d) Line traces of RxxR_{xx} vs. VSL−VDV_{SL}-V_D at several values of VBGV_{BG}, where VDV_D denotes the Dirac point offset. (e) Line traces of RxxR_{xx} vs. VTG−VDV_{TG}-V_D at several values of VBGV_{BG}. Line traces of RxxR_{xx} vs. VTG−VDV_{TG}-V_D at several values of VSLV_{SL}, with VBGV_{BG} fixed at 70 V. (g) RxxR_{xx} as a function of VTGV_{TG} and VBGV_{BG} at B=8B=8 T for device D2. Two additional minima emerge at higher VBGV_{BG}, marked by blue arrows. (h) Line cuts at VBG=20V_{BG}=20 V (black, top panel) and 40 V (red, bottom panel) after subtracting VDV_D; the minima are marked by blue arrows in the bottom panel. (i) RxxR_{xx} vs. VTG−VDV_{TG}-V_D at several values of VBGV_{BG} and fixed VSL=2V_{SL}=2 V, highlighting the effect of a finite VBGV_{BG}, for device D3. Curves are vertically offset by 4 kΩ\Omega for clarity.

In summary, we have demonstrated the realization of minibands in Bernal-stacked BLG through the application of a SL gate potential. The periodic potential in our devices can be precisely tuned using various combinations of the three independently controlled gates, offering superior electrostatic control over the target 2D layer compared to previous architectures. Our key observation is the emergence of new insulating states near the CNP in BLG with large energy gaps, stabilized by the SL potential. Moreover, Hall measurements reveal signatures of charge carrier inversion, corroborating the formation of minibands. The inclusion of a third, independently tunable Si bottom gate further expands the accessible phase space, enabling dynamic modulation of the SL potential landscape. Theoretical calculations corroborate our experimental findings, demonstrating the formation of distinct minibands and the rapid evolution of the band structure with increasing SL strength. Overall, our results establish a versatile platform for engineering tunable miniband structures in BLG, paving the way for exploring a broad class of artificial lattice potentials and 2D material systems in the future. Whether the underlying physics of these artificially created bands is fundamentally similar to or different from that of twisted moiré bands remains an open question for further exploration. As the first demonstration of a three-gated architecture of this kind, our platform opens several promising directions for future work: (i) stronger superlattice potentials via thinner dielectrics; (ii) moiré-like superlattices with shorter periods; (iii) engineered flat bands hosting complex topological phases and fractional Chern states, as proposed in Ref. [25]; (iv) extension to other material systems, such as oxides, enabling the study of correlation effects under moiré-like potentials without precise twist-angle engineering; and (v) a versatile quantum simulation platform for nontrivial lattice geometries—Dice, Lieb, Kagome, and quasicrystalline structures—that are difficult to realize in naturally occurring materials.

Acknowledgements

We thank A. Ghosh, V. Kochat and E. Tutuc for helpful discussions and comments. We gratefully acknowledge the usage of the MNCF and NNFC facilities at CeNSE, IISc. U.C. acknowledges funding from STARS (STARS-2/2023-0309) and Quantum Research Park, IQTI IISc. R.B. acknowledges funding from the Prime Minister’s Research Fellowship (PMRF), MHRD. M.J. acknowledges the Nano mission of the Department of Science and Technology, India, for financial support under Grant No. DST/NM/TUE/QM-10/2019. M.J. acknowledges the Nano mission of the Department of Science and Technology, India and the Anusandhan National Research Foundation (ANRF-ARG) for financial support under grant nos. DST/NM/TUE/QM-10/2019 and ANRF/ARG/2025/003370/PS, respectively. H.K.P. would like to thank DST SERB, India, for financial support via Grant No. CRG/2021/005453. K.W. and T.T. acknowledge support from the JSPS KAKENHI (Grant Numbers 21H05233 and 23H02052), the CREST (JPMJCR24A5), JST, and World Premier International Research Center Initiative (WPI), MEXT, Japan. This research also benefited from discussions at the International Centre for Theoretical Sciences (ICTS) through the program “Engineered 2D Quantum Materials” (code: ICTS/E2QМ2024/07).

Methods

Device fabrication

Our patterned superlattice gate consists of a triangular network of holes with a period of ∼50\sim50 nm (D1, D3 and D4) and 100 nm (D2). The graphite flake to be patterned was first spin-coated with PMMA 950K A2 at 6000 rpm for 45 seconds, followed by baking at 180 °C for 1 minute. Electron-beam lithography was performed at an acceleration voltage of 30 kV, using a hole array of single-pixel dots. An optimized exposure dose of 0.00825 pC was used to obtain holes approximately 30 nm in diameter and with a periodicity of 50 nm. A 7.5 µm aperture was employed to minimize the beam diameter and reduce feature broadening on the sample. After exposure, the sample was developed in a MIBK:IPA (1:3) solution at ∼5 ∘C\sim5\,^\circ\mathrm{C}, followed by rinsing in IPA for 5 seconds at the same temperature to slow down the development process. The developed regions were then etched using reactive ion etching. The fabrication of the heterostructures began with a dry transfer process using a polycarbonate (PC) film. Each individual layer was sequentially picked up at a temperature of approximately 110 ∘C110\,^\circ\mathrm{C} and finally released onto a target substrate of SiO2_2 (285 nm)/Si at around 160 ∘C160\,^\circ\mathrm{C}. The assembled stack was shaped into a multi-terminal Hall bar geometry via reactive ion etching using CHF3_3/O2_2 gas. Electron-beam lithography followed by thermal evaporation of Cr/Au (5 nm/60 nm) was employed to define Ohmic edge contacts and the top gate.

Transport Measurements

Electrical transport measurements were performed in a cryogen-free, pumped 4He^4\mathrm{He} cryostat equipped with a 9 T superconducting magnet and a base temperature of 1.6 K. The measurements were carried out using a bias current in the range of 10-100 nA, sourced through an SR830 lock-in amplifier operating at 17.777 Hz. Keithley 2450 source-measure units (SMUs) were used to apply the DC gate voltages. The voltage signal was amplified using a DL1201 preamplifier before lock-in detection.

Theory

We investigate the low-energy electronic spectrum of Bernal-stacked bilayer graphene subjected to a displacement field and a superlattice potential using the continuum model [18, 40]. The total Hamiltonian is expressed as

H=HBLG+HV+HSL,H = H_{\mathrm{BLG}} + H_V + H_{\mathrm{SL}},

where HBLGH_{\mathrm{BLG}} represents the intrinsic bilayer graphene Hamiltonian, HVH_V corresponds to the gate-induced mean potential, and HSLH_{\mathrm{SL}} accounts for the superlattice modulation.

The mean potential term is given by

HV=[V0(1)σ00202V0(2)σ0]H_V = \begin{bmatrix} V_0^{(1)}\sigma_0 & 0_2 \\ 0_2 & V_0^{(2)}\sigma_0 \end{bmatrix}

where V0(1)V_0^{(1)} and V0(2)V_0^{(2)} denote the average electrostatic potentials acting on layers 1 and 2, respectively.

The superlattice gate introduces a spatially varying two-dimensional cosine potential of the form

HSL=12[VSL(1)σ00202VSL(2)σ0]∑n=16cos⁡(Gn⋅r),H_{\mathrm{SL}} = \frac{1}{2} \begin{bmatrix} V_{\mathrm{SL}}^{(1)}\sigma_0 & 0_2 \\ 0_2 & V_{\mathrm{SL}}^{(2)}\sigma_0 \end{bmatrix} \sum_{n=1}^{6}\cos(\mathbf{G}_n\cdot\mathbf{r}),

where VSL(1)V_{\mathrm{SL}}^{(1)} and VSL(2)V_{\mathrm{SL}}^{(2)} are the modulation amplitudes for layers 1 and 2. The reciprocal lattice vectors of the superlattice are defined as Gn=G(cos⁡(2πn6),sin⁡(2πn6))\mathbf{G}_n=G\left(\cos\left(\frac{2\pi n}{6}\right),\sin\left(\frac{2\pi n}{6}\right)\right). In the corresponding mini Brillouin zone, the high-symmetry points ΓS\Gamma_{\mathrm{S}}, MS\mathrm{M}_{\mathrm{S}}, and KS\mathrm{K}_{\mathrm{S}} are located at (0,0)(0,0), 12G0\frac{1}{2}\mathbf{G}_0, and 13(G0+G1)\frac{1}{3}(\mathbf{G}_0+\mathbf{G}_1), respectively.

The potential parameters, estimated from the carrier density data (see Supplemental Material Section III A), are given by

V0(1)=64.60(1−α)VTG+64.60αVSL meV,V_0^{(1)} = 64.60(1-\alpha)V_{\mathrm{TG}} + 64.60\alpha V_{\mathrm{SL}}\ \mathrm{meV},
V0(2)=64.60αVTG+64.60(1−α)VSL meV,V_0^{(2)} = 64.60\alpha V_{\mathrm{TG}} + 64.60(1-\alpha)V_{\mathrm{SL}}\ \mathrm{meV},
VSL(1)=4.54αVSL meV,V_{\mathrm{SL}}^{(1)} = 4.54\alpha V_{\mathrm{SL}}\ \mathrm{meV},
VSL(2)=4.54(1−α)VSL meV,V_{\mathrm{SL}}^{(2)} = 4.54(1-\alpha)V_{\mathrm{SL}}\ \mathrm{meV},

where α\alpha is the screening parameter, VTGV_{\mathrm{TG}} denotes the top-gate voltage, and VSLV_{\mathrm{SL}} represents the applied superlattice-gate voltage.

Using this continuum model, the electronic band structures along the high-symmetry path of the mini Brillouin zone (see Supplemental Material Figs. S24-25) and the resistivity are computed for various values of VSLV_{\mathrm{SL}} (see Figure 2g,Figure 2i).

Author Contributions

S.S. fabricated the devices. S.B. assisted in device fabrication, performed the measurements, and analysed the data. A.M. and R.B. performed the theoretical calculations, supervised by H.K.P. and M.J., respectively. S.D. and R.S.B. assisted with measurements. K.W. and T.T. grew the hBN crystals. S.B., A.M., R.B., M.J., H.K.P., and U.C. co-wrote the manuscript. U.C. supervised the project.

Competing interests

The authors declare no competing interests.

Supplemental Material: A tunable multi-gated platform for superlattice engineering in bilayer graphene

Experimental results

Device fabrication and basic characterization

The device fabrication started with transferring the flakes in the required stacking order, followed by defining the Hall-bar geometry and making electrical contacts. First, a graphite flake was transferred onto a SiO2\mathrm{SiO}_2/Si wafer using a PC polymer film on a PDMS stamp. The graphite was then patterned using the recipe described in the Methods section of the main text. Figure S1 shows the optical image of the patterned graphite, and the corresponding SEM image in Figure S1. Figure S1 highlights the triangular periodic array of holes (dark circular regions). A heterostructure consisting of hBN/bilayer graphene/hBN was subsequently transferred onto the patterned gate (Figure S1). The stack was processed in multiple steps: depositing a metal top gate, etching the Hall-bar geometry, and finally forming 1D edge contacts. We used Cr/Au (5 nm/50 nm) for the top gate and Cr/Au (10 nm/100 nm) for the edge contacts. The optical image of the final device is presented in Figure S1.

Optical image of the patterned graphite flake

(a)

SEM image of the patterned graphite

(b)

Optical image of the top hBN/bilayer graphene/bottom hBN heterostructure

(c)

Optical image of the completed device

(d)

Figure S1. Device fabrication. a Optical image of the patterned graphite flake transferred onto a SiO2\mathrm{SiO}_2/Si substrate. The scale bar is 10 μ\mum. b SEM image of the patterned graphite, showing the triangular periodic array of holes (dark circular features). The scale bar is 100 nm. c Optical image of the top hBN/bilayer graphene/bottom hBN heterostructure transferred onto the patterned graphite gate. d Optical image of the completed device with a scale bar of 10 μ\mum. All images are for device D1.

In Figure S2, we show the estimation of mobility μ\mu in our device. μ\mu is calculated using Drude conductivity σ=neμ\sigma= ne\mu, where nn is the number density, ee is the charge of an electron. However, fitting a straight line in σ\sigma vs. nn plot often leads to an error in the estimation of μ\mu as it depends on the range of fitting. Therefore, we have plotted 1e∣dσdn∣\frac{1}{e}\left|\frac{d\sigma}{dn}\right| which saturates at finite nn on both electron and hole side, indicating σ\sigma is linear in nn. The μ\mu values are found to be 340,000 cm2V−1s−1\mathrm{cm}^2\mathrm{V}^{-1}\mathrm{s}^{-1} on the electron and 200,000 cm2V−1s−1\mathrm{cm}^2\mathrm{V}^{-1}\mathrm{s}^{-1} on the hole side. Device D2 and D3 also exhibit high mobility of 150,000–200,000 cm2V−1s−1\mathrm{cm}^2\mathrm{V}^{-1}\mathrm{s}^{-1} and 90,000–100,000 cm2V−1s−1\mathrm{cm}^2\mathrm{V}^{-1}\mathrm{s}^{-1}, respectively.

Figure S2. Mobility calculations a. 1e∣dσdn∣\frac{1}{e}\left|\frac{d\sigma}{dn}\right| is plotted as a function of nn, where σ\sigma is the electrical conductivity, and ee is the charge of an electron. The saturation of 1e∣dσdn∣\frac{1}{e}\left|\frac{d\sigma}{dn}\right| leads to a mobility of 340,000 cm2^{2}V−1^{-1}s−1^{-1} on the electron and 200,000 cm2^{2}V−1^{-1}s−1^{-1} on the hole side. Data shown for device D1. Devices D2 and D3 also showed similar values.

Figure S3 displays the color map of the longitudinal resistance, RxxR_{xx}, as a function of top gate (TG) voltage VTGV_{\mathrm{TG}} and superlattice (SL) gate voltage VSLV_{\mathrm{SL}}, with corresponding horizontal line cuts shown in Figure S3. The charge neutrality point (CNP) shifts along a diagonal trajectory in the color plot, accompanied by an increase in the magnitude of resistance. Multiple prominent peaks emerge at higher VSLV_{\mathrm{SL}}. Notably, for VSL>3V_{\mathrm{SL}} > 3 V, a tiny peak is observed situated between two dominant peaks (indicated by the black arrow).

Figure 2 in the main text shows the phase space obtained by sweeping the TG at a discrete SL gate voltage. The features are found to be stabilized by the periodic displacement field DD by the combination of both gates. In Figure S4, we show the reverse configuration obtained by sweeping the SL gate at discrete TG voltages. Multiple peaks in RxxR_{xx} appear at a finite periodic DD field. Figure S4 shows the color plot. The line plots at VTG=±4V_{TG} = \pm4 V are shown in Figure S4-Figure S4. The insets show a closer view of the third weaker peak that appears at a high electric field. These results are identical to those shown in Figure 2 of the main text.

Phase space and line plots of $R_{xx}$ as a function of $V_{SL}$

Figure S4. Phase space by sweeping the SL gate. a, RxxR_{xx} measured by sweeping VSLV_{SL} at discrete VTGV_{TG}. Similar to Figure 2 in the main text, three peaks are observed in RxxR_{xx} at finite VTGV_{TG} values. b.-c. Line plots of RxxR_{xx} as a function of VSLV_{SL} at VTG=±4V_{TG} = \pm4 V. The insets show a closer view of the weaker peak. The measurements were performed at T=1.8T = 1.8 K.

In Figure S5, we show the estimation of the superlattice period from the densities corresponding to the secondary peaks. Figure S5 shows the phase space of RxxR_{xx} vs VTG−VDV_{TG} - V_D for different values of VSLV_{SL}. The black and red points show the evolution of IS2IS2 and IS3IS3, respectively. Figure S5 shows this more clearly, where the VSLV_{SL} values corresponding to the peaks are plotted. As can be seen, the peak positions shift toward higher VTG−VDV_{TG} - V_D, and hence higher density, as VSLV_{SL} increases. In Figure S5, we estimate the lattice constant using the density nn obtained from the electrostatic capacitance; assuming a triangular lattice structure, we find a period LL between 30-60 nm, close to the lithographically defined period of ∼50\sim50 nm. The effective reduction of the period is a consequence of the electrostatics of the patterned gate voltage when a finite voltage is applied.

Four-panel plots showing phase space, peak positions, estimated superlattice period, and estimated Fermi energy

Figure S5. Estimation of the superlattice period and characteristic energy scale. a. Phase space of RxxR_{xx} as a function of VTG−VDV_{TG}-V_D and VSLV_{SL}. Black and red points mark the evolution of the resistance peaks IS2IS2 and IS3IS3, respectively. b. Evolution of the IS2IS2 and IS3IS3 peak positions with VSLV_{SL}, extracted from (a). c. Estimated superlattice period LL obtained from the carrier density corresponding to the peak positions, assuming a triangular superlattice. The extracted values are of the same order as the nominal superlattice period of 50 nm. d. Estimated Fermi energy EFE_F associated with the IS2IS2 and IS3IS3 peak positions as a function of ∣VSL∣\lvert V_{SL}\rvert, calculated assuming a parabolic dispersion with an effective mass m∗=0.05mem^* = 0.05m_e. The gray dashed line marks the characteristic energy scale Δ=40\Delta= 40 meV. The extracted EFE_F values remain below this energy scale over the measured range.

original charge neutrality point of bilayer graphene at VSL=0V_{SL} = 0 V. IS2IS2 denotes the first secondary peak at finite VSLV_{SL} and is associated with the first miniband gap on the hole side (VTG−VD<0V_{TG} - V_D < 0 V), whereas IS3IS3 corresponds to the higher-VSLV_{SL} secondary peak associated with the electron side (VTG−VD>0V_{TG} - V_D > 0 V). For VSL<0V_{SL} < 0 V, the features are approximately mirror symmetric, and the labels of IS2IS2 and IS3IS3 are reversed accordingly.

We further estimate the Fermi energy EFE_F associated with the IS2 and IS3 minibands as a function of VSLV_{SL}, using the carrier densities extracted from the peak positions and an effective mass of m∗=0.05mem^* = 0.05m_e (Figure S5). Across the entire range of superlattice potential investigated, the estimated EFE_F remains below ∼15\sim15 meV. In comparison, the experimentally extracted gap of ∼40\sim40 meV is approximately two to three times larger than EFE_F at the highest VSLV_{SL}.

In Figure S6, the three insulating states are labelled IS1IS1, IS2IS2, and IS3IS3. For VSL>0V_{SL} > 0 V, IS1IS1 corresponds to the

Phase of $R_{xx}$ versus density $n$ and superlattice voltage $V_{\mathrm{SL}}$

Figure S6. The whole phase of RxxR_{xx} vs. density nn and superlattice voltage VSL−RxxV_{\mathrm{SL}} - R_{xx} plotted as a function of total density nn and whole range of VSLV_{\mathrm{SL}} values. Three primary resistance peaks are marked as IS1IS1, IS2IS2, and IS3IS3. The position of IS2IS2 and IS3IS3 with respect to IS1IS1 are reversed based on the sign of VSLV_{\mathrm{SL}}.

Temperature dependence

The temperature dependence of RxxR_{xx} can give information about the band gap for insulating states. In Figure S7, we show TT dependence of RxxR_{xx} vs. VTGV_{TG} at different VSLV_{SL}. All four panels (four SL voltages) show the insulating nature of the peaks in RxxR_{xx} up to a highest T=140T = 140 K. In Figure S7-Figure S7, RxxR_{xx} is plotted for VSL=−2V_{SL} = -2 V and −3-3 V, where a single peak is observed, marked by the blue arrow (IS1IS1 as defined in the main text). Figure S7-Figure S7 shows RxxR_{xx} vs. VTGV_{TG} at VSL=−4V_{SL} = -4 V, −5-5 V, which clearly show two peaks with the secondary peak (IS2IS2 as defined in the main text) marked by a black arrow. Both the peaks remain insulating up to a high T=140T = 140 K.

To estimate the energy gap, we plot the peak values of RxxR_{xx} as a function of 1/T1/T. Prior studies have shown that at low temperatures (T≤30T \le30 K in our case), the peak resistance weakly depends on 1/T1/T, consistent with variable range hopping (VRH) or a combination of VRH and nearest-neighbor hopping at low and intermediate TT. At higher temperatures (T≥60T \ge60 K), however, RxxR_{xx} exhibits thermally activated behavior, following:

Rxx∝exp⁡(Δ/2kBT),R_{xx} \propto\exp(\Delta/2k_{B}T),

where Δ\Delta is the energy gap and kBk_{B} is the Boltzmann constant. Fitting this relation to the RxxR_{xx} versus 1/T1/T data allows us to extract Δ\Delta. Figure S8-Figure S8 shows the peak RxxR_{xx} of IS1IS1 as a function of 1/T1/T for VSL=−2V_{SL} = -2 V and −3-3 V. From the slope of the dashed red fit lines, the extracted gaps are found to be on the order of tens of meV. A similar activated behavior is observed for IS2IS2 at higher VSLV_{SL} values of −4-4 V and −5-5 V, as shown in Figure S8-Figure S8. Repeating this process for each VSLV_{SL}, we extract Δ\Delta and study its evolution with VSLV_{SL}. Although fitting the Arrhenius equation is a standard method for extracting energy gaps in the case of thermally activated transport, the results are highly sensitive to the temperature range chosen for the fit. Even small variations in the selected TT range can lead to significantly different energy gap values. Therefore, transport measurements alone are not sufficient to determine the energy gaps with high accuracy. In our analysis, we have used the fit that yields the lowest error in the higher temperature regime.

Figure S9-Figure S9 presents the temperature dependence of RxxR_{xx} measured by sweeping VSLV_{SL} at fixed VTG=±4.6V_{TG} = \pm4.6 V, up to 130 K and 170 K, respectively. Both plots exhibit two prominent peaks (IS1IS1 and IS2IS2), which are indicated by blue and black arrows, respectively. In Figure S9-Figure S9, we have plotted the maximum resistance of IS1IS1 and IS2IS2 as a function of 1/T1/T. Fitting the data with the red dashed lines gives gap values of approximately in the range of ≈52−65\approx52 - 65 meV, which is slightly larger than the gaps extracted in Figure 3e-Figure 3f. This difference may arise from a pristine gap resulting from reduced charge disorder when using a graphite gate instead of a metal gate, as previously reported [35].

Activated energy gaps obtained from the SL gate sweep

Figure S9. Activated energy gaps obtained from the SL gate sweep. a. RxxR_{xx} vs. VSLV_{SL} at VTG=4.6V_{TG}=4.6 V plotted in a range of T=7.5T=7.5 K to 130 K. The blue and black arrow denotes the states IS1IS1 and IS2IS2, respectively. b. RxxR_{xx} vs. VSLV_{SL} at VTG=−4.6V_{TG}=-4.6 V plotted in a range of T=5T=5 K to 170 K. c.-d. At VTG=4.6V_{TG}=4.6 V Peak resistance for IS1IS1 (blue circles) and IS2IS2 (black circles) plotted as a function of 1/T1/T. The slope of the dashed line results in Δ\Delta of 65±565 \pm5 meV for IS1IS1 and 52±352 \pm3 meV for IS2IS2. e.-f. Similar fitting is done for VTG=−4.6V_{TG}=-4.6 V for IS1IS1 and IS2IS2. The obtained Δ\Delta values are 62±462 \pm4 meV for IS1IS1 and 55±355 \pm3 meV for IS2IS2. Data for device D1.

Analysis of thermally activated transport does not necessarily provide a robust estimate of the energy gap [35, 41]. To assess the reliability of the extracted activation gap, we fit the temperature-dependent resistance using the thermally activated form Rxxmax⁡=R0exp⁡(Δ/2kBT)R_{xx}^{\max} = R_{0}\exp(\Delta/2k_{B}T) over three different 1/T1/T intervals. As shown in Figure S10-Figure S10, different temperature ranges of the data can be reasonably described by thermally activated behavior. However, the corresponding extracted values of Δ\Delta depend strongly on the selected fitting range, with a small shift of approximately 5 K in the lower temperature bound resulting in a change of approximately 5 meV in Δ\Delta. These results demonstrate that the extracted activation energy is highly sensitive to the temperature interval chosen for fitting, indicating that activated-transport analysis may not always provide a reliable estimate of the underlying energy gap.

Summary of transport data in Sections A and B

As discussed above, the additional insulating states, IS2IS2 and IS3IS3, emerge only upon applying a finite superlattice potential, whereas conventional BLG behavior with a single CNP feature (IS1IS1) is recovered in its absence. This, together with the emergence of multiple resistance peaks at finite periodic displacement field, supports their origin from a superlattice-induced reconstruction of the BLG band structure rather than from conventional BLG physics alone. A particularly important signature is the pronounced electron-hole asymmetry of these states: upon reversing the sign of VSLV_{SL}, the relative positions of IS2IS2 and IS3IS3 are reversed. This behavior is reproduced by our band-structure calculations, which show that reversing VSLV_{SL} inverts the electron-hole asymmetry, providing qualitative agreement between experiment and theory. We further characterize these insulating states through their temperature dependence. At high temperatures, where thermally activated transport dominates, Arrhenius analysis provides an order-of-magnitude estimate of the associated energy gaps. Although the extracted values are sensitive to the selected fitting window and should therefore not be regarded as precise measurements of the band gaps, their overall energy scales are broadly consistent with the theoretical calculations. This combined agreement in the emergence, gate-polarity dependence, and characteristic energy scales of the insulating states provides evidence that IS2IS2 and IS3IS3 originate from the superlattice-engineered miniband structure.

Transport data in the presence of a magnetic field

In Figure S11, we present contour plots of RxxR_{xx} and RxyR_{xy} as a function of VTG−VDV_{TG}-V_D for positive and negative VSLV_{SL} values at B=1B=1 T and VBG=−20V_{BG}=-20 V. At VSL=0V_{SL}=0 V, a single sign change is observed, corresponding to carrier inversion at the CNP of bilayer graphene. However, with increasing VSLV_{SL}, new resistive peaks and corresponding sign changes in RxyR_{xy} emerge. The sign changes in RxyR_{xy} somewhat match with the peaks in RxxR_{xx} and may be associated with Fermi surface reconstructions and charge carrier inversion upon crossing band gaps.

Phase space of $R_{xx}$ and $R_{xy}$ at $B=1$ T and $V_{BG}=-20$ V

Figure S11. Phase space of RxxR_{xx} and RxyR_{xy} at B=1B=1 T and VBG=−20V_{BG}=-20 V. a. RxxR_{xx} plotted as a function of positive SL voltage VSLV_{SL} and VTG−VDV_{TG}-V_D, where VTGV_{TG} is the top gate voltage and VDV_D is the CNP offset. Two peaks are clearly observed. b. RxyR_{xy} is plotted in the same range of gate voltages. Sign changes are observed for the peaks in RxxR_{xx}. c. RxxR_{xx} plotted as a function of negative SL voltage VSLV_{SL} and VTG−VDV_{TG}-V_D. d. RxyR_{xy} is plotted in the same range of gate voltages. Similar to panel b, multiple sign changes are observed for the peaks in RxxR_{xx}. Data for device D1.

COMSOL simulations

In order to find the charge density profile on BLG due to the patterned graphite gate, we have used the COMSOL Multiphysics simulation. The geometry was constructed using COMSOL Multiphysics 6.0. Figure S12 shows the model, where holes with a diameter of 25 nm are patterned in a graphite layer (shown in purple). The superlattice period is fixed at 50 nm, matching that of the patterned graphite gate in our device. The bilayer graphene (BLG, shown in orange) is separated from the graphite gate by a 14 nm-thick bottom hBN dielectric layer (cyan). This hBN thickness was estimated from low-field Hall measurements. In the simulation, the BLG is modeled as a grounded metallic sheet. with its upper boundary set at VBLG=0V_{BLG} = 0 V. A finite voltage VSLV_{SL} is applied to the graphite gate to determine the induced gate voltage profile in the device. Since the BLG is grounded, the top hBN layer is excluded from the model, as it does not affect the induced charge density from the patterned graphite gate. These details are shown in the Table S1.

ParameterValueDescription
Hole diameter25 nmDiameter of holes patterned in the graphite gate
Superlattice period50 nmPeriodicity of the patterned graphite gate
Bottom hBN thickness14 nmSeparation between BLG and patterned graphite gate
Active layerBLGBilayer graphene
Patterned gateGraphiteGraphite layer containing the periodic hole array
DielectrichBNBottom dielectric separating BLG from graphite

Table S1. Device parameters

COMSOL model showing graphene, bottom hBN, and graphite layers with a periodic hole array

Figure S12. COMSOL model. Three vertically stacked blocks are made in COMSOL. Graphene and bottom hBN are denoted by the orange and cyan colors, respectively. The holes with a diameter of 25 nm are made in the graphite layer (purple color). A lattice periodicity of 50 nm was chosen for the simulation. The total dimension of the model system is 150 nm ×\times 129 nm.

The dielectric constant of hBN was explicitly defined within the material properties. The graphite gate was modeled as a standard metallic electrode, similar to gold, to simplify the boundary conditions. We employed the electrostatics module in COMSOL, where charge conservation is inherently enforced. First, simulations were carried out using a plain graphite gate configuration, and the resulting charge density profiles showed good agreement with estimates derived from electrostatic capacitance calculations. This consistency validates the reliability of our modeling approach for capturing the spatial charge distribution in the system. The surface charge density σ(r⃗)\sigma(\vec{r}) on the BLG is obtained from the displacement field D⃗\vec{D} via σ(r⃗)=n^⋅D⃗\sigma(\vec{r}) = \hat{n} \cdot\vec{D}, where n^\hat{n} is the unit normal vector to the BLG plane. Figure S13-Figure S13 shows the spatial distribution of σ(r⃗)\sigma(\vec{r}) in the xx–yy plane at VSL=1V_{SL} = 1, 3 and 5 V, in units of mC/m2^2. It is observed that σ(r⃗)\sigma(\vec{r}) is minimum inside the holes and maximum outside. The negative sign of σ(r⃗)\sigma(\vec{r}) indicates electron doping. Figure S13-Figure S13 presents the carrier density distribution n2D=σ/en_{2D} = \sigma/e in the BLG plane at VSL=1V_{SL} = 1, 3 and 5 V, revealing clear density modulation. In Figure S14, we show the maximum and minimum in the oscillating profile of n2Dn_{2D} for VSLV_{SL} values from 1 to 5 V. The value of nmax⁡n_{\max} matches with the carrier density expected from a uniform gate voltage at the corresponding VSLV_{SL}. We define the amplitude of density modulation as Δn=nmax⁡−nmin⁡\Delta n = n_{\max} - n_{\min}. Notably, Δn\Delta n also increases linearly with increasing VSLV_{SL} (Figure S14).

Simulation of charge density

Figure S13. Simulation of charge density. a.-c. The 2D profile of surface charge density σ\sigma on BLG when a constant dc voltage of VSL=1V_{SL}=1, 3, and 5 V is applied to the graphite gate. The density in the hole region is non-zero because of the fringing effect of the sub-nm pattern. b. Charge carrier density n2D=σ/en_{2D}=\sigma/e shown three superlattice gate voltages shown in a. The density is minimum inside the holes and maximum outside the holes. Both σ\sigma and n2Dn_{2D} increase with increasing VSLV_{SL} as shown by the minima and maxima of the colour bars.

Figure S14. Estimation of maximum and minimum density from COMSOL. a. Maximum and minimum density nmax⁡n_{\max} and nmin⁡n_{\min}, respectively obtained from the oscillating profile of n2Dn_{2D} is plotted as function of VSLV_{SL}. The magnitude of both the quantities increases with increasing VSLV_{SL}. b. Difference Δn=nmax⁡−nmin⁡\Delta n = n_{\max} - n_{\min} plotted as a function VSLV_{SL} also shows a increasing trend with increasing VSLV_{SL}.

The thickness of the bottom hBN plays a crucial role in determining the modulation of density Δn\Delta n. If the thickness of the bottom hBN becomes comparable to the period of the superlattice, then it gives rise to a smooth density profile on BLG. Figure S15 shows the spatial distribution of n2Dn_{2D} at VSL=2V_{SL}=2 V for two thicknesses of hBN of 14 nm (Figure S15) and 33 nm (Figure S15). We note that Δn\Delta n is significantly reduced for a 33 nm-thick hBN layer compared to 14 nm. This indicates that the influence of the superlattice gate becomes weaker with increasing bottom hBN thickness. We have estimated the total density nn as a function of the density from the top gate nTGn_{TG} and the superlattice gate nSLn_{SL} and expressed as n=nTG+nSL+n0n=n_{TG}+n_{SL}+n_0, where n0=−0.25×1016n_0=-0.25 \times10^{16} is the residual carrier density. nSLn_{SL} is an average density of nmax⁡n_{\max} and nmin⁡n_{\min} and can be expressed as nSL=αnmax⁡+βnmin⁡n_{SL}=\alpha n_{\max}+\beta n_{\min} where α\alpha and β\beta are the fraction of area of the total area for plain graphite and holes in the graphite.

Number-density maps for 14 nm and 33 nm bottom hBN thicknesses

Figure S15. hBN thickness dependence of number density. a.-b. Number density from the superlattice gate n2Dn_{2D} plotted as a function of xx and yy at a superlattice gate voltage VSL=2V_{SL} = 2 V for a bottom hBN thickness of 14 nm and 33 nm, respectively. The modulation of density is extremely weak, and the potential variation is found to be almost uniform for the 33 nm hBN, with a variation of Δn=−0.02×1016\Delta n = -0.02 \times10^{16} m−2^{-2}. The simulation for a bottom hBN thickness of 14 nm shows an enhanced density modulation with a Δn=−0.86×1016\Delta n = -0.86 \times10^{16} m−2^{-2} at VSL=2V_{SL} = 2 V.

We now calculate the periodicity dependence of the charge density in BLG. Figure S16 illustrates the charge density, n2Dn_{2D}, for superlattice periods of 50 nm and 100 nm. The 50 nm period consists of 25 nm diameter holes separated by 25 nm, while the 100 nm period features 50 nm holes with 50 nm spacing. At VSL=4V_{SL}=4 V, the density modulation is notably stronger for the 100 nm SL compared to the 50 nm case (compare Figure S16-Figure S16 and Figure S16-Figure S16). This amplitude is determined by the interplay between the hole diameter and the thickness of the dielectric layer.

Charge density distributions and line cuts for 50 nm and 100 nm period superlattices

Figure S16. Periodicity dependence of the charge density (n2Dn_{2D}). a.-b. Charge density distribution for a SL with a 50 nm period (25 nm diameter holes separated by 25 nm spacing). The line cut is taken along the horizontal dashed line in a. c.-d. Charge density for a 100 nm period SL (50 nm diameter holes separated by 50 nm spacing). Calculations are shown for a superlattice gate voltage VSL=4V_{SL} = 4 V. The density modulation is observed to be stronger for the 100 nm period due to the relationship between hole diameter and dielectric layer thickness.

The application of a global Si bottom gate (BG) also induces a periodic charge density, as discussed in the Supplemental Material and Figure 4 of the main text. Figure S17 and c display spatial maps of n2Dn_{2D} at VBG=30V_{BG}=30 V for 50 nm and 100 nm SLs, respectively. Analogous to the SL gate, the BG induces a finite modulation where the magnitude depends on VBGV_{BG} and the bottom dielectric thickness. Notably, the density is observed to be higher for the 100 nm SL (see line plots in Figure S17 and d).

Charge density modulation induced by the global Si bottom gate

Figure S17. Charge density modulation induced by the global Si bottom gate. a. Spatial x−yx-y map of n2Dn_{2D} for the 50 nm period SL at a back gate voltage VBG=30V_{BG} = 30 V. b. Corresponding line plot of n2Dn_{2D} along the horizontal dashed line in a. c. Spatial x−yx-y map of n2Dn_{2D} and d. corresponding line plot for the 100 nm period SL at VBG=30V_{BG} = 30 V. The bottom gate induces a periodic modulation dependent on dielectric thickness, with higher density observed for the 100 nm SL.

Additional Transport Data

In the following we discuss various transport measurements performed on three additional devices D2, D3 and D4, demonstrating consistency and reproducibility of our gate-engineering approach, while also investigating factors such as dielectric thickness dependence and gate tunability. In Figure S18, we show the transport data of device D2, in which a global Si BG was used to apply a periodic potential on BLG, given that the SL graphite gate acts as a screening layer. The hBN layer separating BLG from SiO2SiO_2 has a thickness of 33 nm. Figure S18 shows RxxR_{xx} as a function of VTGV_{TG} at T=1.8T = 1.8 K, where a single peak at the CNP is observed. The application of VBGV_{BG} leads to a secondary shoulder peak (Figure S18). The color map of RxxR_{xx} vs. VTGV_{TG} and VBGV_{BG} illustrates the evolution of the peaks (Figure S18). A closer look at the higher VBGV_{BG} clearly shows two peaks in RxxR_{xx}, as indicated by two black arrows.

Figure S18. Transport characteristics of device D2. a. Longitudinal resistance RxxR_{xx} as a function of top gate voltage VTGV_{TG} at T=1.8T = 1.8 K, showing a single peak at the CNP. b. Application of a finite VBGV_{BG} gives rise to an additional shoulder peak. c. Color map of RxxR_{xx} as a function of VTGV_{TG} and VBGV_{BG}, illustrating the evolution of the peaks, where two distinct resistance maxima emerge at higher VBGV_{BG} (indicated by black arrows) in the zoomed-in panel in d.

Figure S19 shows the Landau fan diagram where RxxR_{xx} is plotted as a function of VTGV_{TG} and BB at VBG=0V_{BG} = 0 V. As a finite BB field, we find a series of minima emerging from the CNP. These minima are attributed to the Landau levels, and the filling factor can be estimated by fitting the Diophantine equation, B=hνe(n−s)B = \frac{h}{\nu e}(n - s), where nn is the charge carrier density, ν\nu is the Landau filling factor, BB is the magnetic field, hh is Planck’s constant, ee is the charge of an electron, and ss is charge density at B=0B = 0 T. In our analysis, n=CTG(VTG−VD)/en = C_{TG}(V_{TG} - V_D)/e, where CTGC_{TG} is the top gate capacitance per area and VDV_D is the residual gate voltage at the CNP. The slope of the dashed lines (Diophantine equation) gives the filling factor ν\nu. In the absence of VBGV_{BG}, we find four-fold degenerate Landau levels with ν=±4,±8,±12,…\nu= \pm4, \pm8, \pm12,\ldots, appearing from the CNP at VD∼0.5V_D \sim0.5 V [42]. These results are consistent with the conventional behavior of BLG without a periodic potential. In Figure S20, we present the data for VBG=30V_{BG} = 30 V. We find a departure of ν\nu from the standard BLG-like ν\nu (Figure S20). Interestingly, two primary sets of lines with opposite signs of ν\nu appear from two different densities. The red dashed lines appear from the CNP peak, and the grey dashed lines appear from the secondary peak. We also find a significant asymmetry in ν\nu values for these two sets, possibly determined by the spin valley symmetry breaking. In addition, we find a state with ν=4\nu= 4 (blue dashed line) that appears from a higher density at higher BB and may be attributed to remote bands. Figure S21, we show the line traces of RxxR_{xx} vs. VTGV_{TG} at VBG=30V_{BG} = 30 V for B=5−9B = 5 - 9 T, where the evolution of the Landau levels is clearly visible. These line plots are obtained from Figure S20.

Landau fan diagram of BLG at VBG = 0 V

Figure S19. Landau fan diagram of BLG at VBG=0V_{BG} = 0 V; Device D2. Longitudinal resistance RxxR_{xx} plotted as a function of top gate voltage VTGV_{TG} and magnetic field BB at VBG=0V_{BG} = 0 V. A series of minima emerge from the CNP with increasing BB, corresponding to the formation of Landau levels. We observe four-fold degenerate Landau levels with ν=±4,±8,±12,…\nu= \pm4, \pm8, \pm12,\ldots emanating from the CNP at VD∼0.5V_D \sim0.5 V.

Landau fan diagram of BLG at $V_{BG}=30$ V; Device D2

Figure S20. Landau fan diagram of BLG at VBG=30V_{BG}=30 V; Device D2 a. Longitudinal resistance RxxR_{xx} plotted as a function of top gate voltage VTGV_{TG} and magnetic field BB at VBG=30V_{BG}=30 V. A clear departure from the standard BLG-like filling factor ν\nu is observed. The red dashed lines originate from the CNP peak, while the grey dashed lines emerge from the secondary peak. A pronounced asymmetry in ν\nu values for these two sets suggests spin-valley symmetry breaking. Additionally, a state with ν=4\nu=4 (blue dashed line) appears from a higher carrier density at larger BB, likely associated with remote bands. The slopes of these lines are shown in b.

Figure S21. Line traces of longitudinal resistance at finite magnetic fields for device D2. Longitudinal resistance RxxR_{xx} as a function of top gate voltage VTGV_{TG} at VBG=30V_{BG}=30 V for magnetic fields B=5−9B=5-9 T. These line traces, extracted from Figure S14, clearly show the evolution and splitting of Landau levels with varying magnetic field.

Figure S22 presents data for a third device, D3, which has an SL period of ∼50\sim50 nm. The effect of VSLV_{SL} on this device is relatively weak, attributed to the thicker bottom hBN layer (∼33\sim33 nm; see Figure S15). However, applying a Si VBGV_{BG} enhances the modulation. Figure S22 displays RxxR_{xx} vs. VTGV_{TG} traces for VSL=0−6V_{SL} = 0 - 6 V at a fixed VBG=5V_{BG} = 5 V. While the magnitude of RxxR_{xx} increases with increasing VSLV_{SL}, the secondary peak remains notably weaker than in the other two devices. The color map of dRxx/dVTGdR_{xx}/dV_{TG} (Figure S22), corrected for the VCNPV_{CNP} shift, reveals a single sign change, confirming the presence of only a single peak. Notably, increasing VBGV_{BG} induces a qualitative difference: at VBG=55V_{BG} = 55 V, a distinct secondary peak emerges within the same VSLV_{SL} range (see Figure S22 and Figure S22).

Transport characteristics of device D3

Figure S22. Transport characteristics of device D3. a., c., e. Longitudinal resistance RxxR_{xx} as a function of top-gate voltage VTGV_{TG} for VSL=0−6V_{SL} = 0 - 6 V at fixed back-gate voltages of VBG=5V_{BG} = 5 V, 35 V, and 55 V, respectively. A distinct secondary peak emerges near the charge neutrality point (CNP) at VBG=55V_{BG} = 55 V. b., d., f. Colour maps of dRxx/dVTG\mathrm{d}R_{xx}/\mathrm{d}V_{TG} plotted against VSLV_{SL} and the normalized gate voltage VTG−VCNPV_{TG} - V_{CNP}, where VCNPV_{CNP} is the Dirac point offset. While the maps for lower VBGV_{BG} display a single sign change at the CNP, two sign changes are visible at VBG=55V_{BG} = 55 V, confirming the presence of the secondary peak.

Figure S23-Figure S23 display RxxR_{xx} vs. VTGV_{TG} for four different combinations of VSLV_{SL} and VBGV_{BG}. In all cases, we observe multiple peaks near the CNP, suggesting the presence of a periodic potential that modulates the band structure on the length scale of the superlattice.

Figure S23. Various configuration of SL potential for device D3. RxxR_{xx} vs. VTGV_{TG} for (VSL,VBG)(V_{SL}, V_{BG}) = a. (−2 V,55 V)(-2\ \mathrm{V}, 55\ \mathrm{V}), b. (−1.5 V,−35 V)(-1.5\ \mathrm{V}, -35\ \mathrm{V}), c. (2 V,55 V)(2\ \mathrm{V}, 55\ \mathrm{V}), d. (3 V,−65 V)(3\ \mathrm{V}, -65\ \mathrm{V}). All four configurations show multiple peaks.

In Figure S24-Figure S24, we show RxxR_{xx} as a function of VTG−VDV_{TG}-V_D for several values of VSLV_{SL}. The data reveal multiple peaks, which we attribute to band gaps emerging at finite VSLV_{SL}. These observations are consistent with those from device D1, presented in the main text.

Phase space of D3

Figure S24. Phase space of D3. (a) Colorplot of RxxR_{xx} vs. VTGV_{TG} for different values of VSLV_{SL}. (b) Line cuts along the horizontal dashed line in (a), showing multiple peaks emerging as VSLV_{SL} increases on both the positive and negative sides, consistent with the behavior of device D1 discussed in the main text.

Lastly, in order to strengthen the claim that the observed features are from superlattice minibands and not due to inherent Dirac point inhomogenieties in the holey and non-holey regions, we present data from an additional device (D4), with a thinner hBN (∼7\sim7 nm) between the BLG and SL gate. This device exhibited multiple resistance peaks in the presence of finite superlattice potentials. Figure S25 shows the RxxR_{xx} vs. (VTG−VD)(V_{TG}-V_D) plot for varying VSLV_{SL}, clearly demonstrating the emergence of three additional peaks on the electron side. A faint feature is observed on the hole side, signifying electron-hole asymmetry, similar to that observed in all other devices.

Additional data for Device D4 showing $R_{\mathrm{xx}}$ versus $(V_{\mathrm{TG}}-V_{\mathrm{D}})$ at different $V_{\mathrm{SL}}$

Figure S25. Additional data for Device D4. RxxR_{\mathrm{xx}} vs. (VTG−VD)(V_{\mathrm{TG}-V_{\mathrm{D}}}) at different VSLV_{\mathrm{SL}} showing multiple peaks marked by the red triangles and arrow are consistent with superlattice-induced band engineering.

In summary, the usage of the multi-gated platform for superlattice engineering offers the following distinct advantages:

  1. The combination of holey and non-holey potentials can be used to enhance the effective superlattice strength. As demonstrated for device D2 (see Figure 4a,Figure 4d, Figure S18), while the additional miniband peaks are hardly observable at a back gate voltage of VBG=0V_{BG}=0, the strength is highly enhanced for a combination of negative and positive VSLV_{SL} and VBGV_{BG}, respectively.

  1. The superlattice potential can be accessed even without an explicit connection to the SL gate, via the non-holey regions and a back gate voltage, as demonstrated for device D3. While this combination reasserts the uniformity of the potential profile across the device, it also offers a very useful experimental method that can be extended to various architectures. For example, this approach allows a graphite gate to be placed very close to the 2D material under study (BLG or other materials, including oxides), while avoiding the fabrication complexity and potential shorting risks associated with integrating a gate electrode directly into the device.

  1. A full combination using all three gates show the expected miniband features, while also offering a rich voltage space to observe the associated features. This effect is exemplified in Figure S22 and Figure S23. While the superlattice effect is minimal owing to a thicker bottom hBN (33 nm), they are enhanced on adding a back gate.

  1. The three-gate configuration provides independent control over the bulk bandgap and the superlattice potential in an electrically tunable material such as BLG. For example, in Figure S23 and Figure S23, by changing the sign and magnitude of the electric field in the patterned hole regions while keeping the electric field and electrostatic potential in the non-holey regions nearly unchanged, we observe an approximately order-of-magnitude difference in resistance between the two configurations, along with a change in the number of resistance peaks. These variations suggest changes in the local bandgap within the hole regions and the overall strength of the resulting superlattice potential, highlighting the additional electrostatic tunability enabled by the three-gate configuration.

We have summarized prior work on engineering the band structure of single- and bilayer graphene via periodic potentials imposed through dielectric or gate patterning (Table S2). We also note reports that mimic such a potential by placing a moiré lattice in proximity to the target layer[22, 23, 24].

RefsMaterialSubstrateLattice structurePeriodGates
[15]SLGPatterned metal gate1D lattice100 nmDual-gate controlled
[16]SLGPatterned SiO2\mathrm{SiO}_22D triangular lattice40 nmDual-gate controlled
[17]SLGPatterned SiO2\mathrm{SiO}_21D lattice60 nmDual-gate controlled
[18]BLGPatterned SiO2\mathrm{SiO}_22D triangular lattice60 nmDual-gate controlled
[19]SLGPatterned graphite gate2D triangular lattice40 nmDual-gate controlled
[20]SLGPatterned graphite gate2D Kagome lattice80 nmDual-gate controlled
This workBLGPatterned graphite gate2D triangular lattice50 nmTriple-gate controlled

Table S2. Summary of papers on dielectric and gate patterning in 2D materials.

In a dual-gated device with one plain gate and one patterned gate, the tunability of the periodic potential is limited by the physical lattice constant of the patterned structure. For dielectric patterning, the amplitude of the potential is determined mainly by the difference in thickness between the holey and non-holey regions, whereas for gate patterning, the amplitude is primarily governed by the lattice constant. A triple-gated structure, with the patterned gate sandwiched between two plain gates, offers greater tunability, since the potential in the holey and non-holey regions can now be tuned independently, enabling the imposition of a complex potential landscape on the target layer. Such a three-gated platform is expected to realize intriguing topological signatures in Bernal bilayer graphene [25], though no previous experimental study has attempted to implement this architecture. Although the predicted topological signatures are not observed in the present work, realizing high-quality electrostatically defined superlattices remains a significant experimental challenge. We anticipate that future studies, with further optimization of the superlattice potential, will enable the observation of the predicted correlated and topological phenomena. Furthermore, the three-gated architecture also ensures that the miniband landscape is accessible even without explicitly contacting the sandwiched graphite gate, ensuring versatility in device fabrication - a combination of top and back gates still provides access to the miniband physics. This could be an important criterion to access miniband physics in engineered heterostructures such as complex oxides where contacting a sandwiched gate layer may pose difficulties.

Theoretical details

Parameter Calculations

The number density depends on both the top gate and superlattice gate voltage. It can be calculated using

n=cTGVTG+cSLVSLe(1)n = \frac{c_{\mathrm{TG}}V_{\mathrm{TG}} + c_{\mathrm{SL}}V_{\mathrm{SL}}}{e} \tag*{(1)}

where cTG=2.36×10−3 C/Vm2c_{\mathrm{TG}} = 2.36 \times10^{-3}\ C/Vm^{2} and cSL=2.36×10−3 C/Vm2c_{\mathrm{SL}} = 2.36 \times10^{-3}\ C/Vm^{2} are the capacitances of the top gate and superlattice gate, respectively. The capacitance values are determined using COMSOL simulations. This gives the total charge induced on both layers. We take the effective mass to be 0.05me0.05m_{\mathrm{e}}, and the density of states is approximated as D=m∗/πℏ2D = m^{*}/\pi\hbar^{2} to estimate the energy.

For VSL=1 VV_{\mathrm{SL}} = 1\ V, the magnitude of the constant charge density induced due to the superlattice gate is 1.348×1012cm−2/V1.348 \times10^{12}\mathrm{cm}^{-2}/V, and the amplitude of charge density is 2.131×1011cm−2/V2.131 \times10^{11}\mathrm{cm}^{-2}/V. The constant charge density arises due to the mean potential generated by the combination of both gate voltages, and the charge density modulation occurs due to superlattice formation. The ratio is 0.158. Converting the charge density modulation to energy gives the amplitude of superlattice modulation to be 10.206VSL10.206V_{\mathrm{SL}} meV. The superlattice Hamiltonian is of the form [18]

HSL=12[VSL1σ00202VSL2σ0]∑n=16cos⁡(Gn⋅r)(2)H_{\mathrm{SL}} = \frac{1}{2} \begin{bmatrix} V_{\mathrm{SL}}^{1}\sigma^{0} & 0_{2} \\ 0_{2} & V_{\mathrm{SL}}^{2}\sigma^{0} \end{bmatrix} \sum_{n=1}^{6}\cos(\mathbf{G}_{n}\cdot\mathbf{r}) \tag*{(2)}

The amplitude of 12∑n=16cos⁡(Gn⋅r)\frac{1}{2}\sum_{n=1}^{6}\cos(\mathbf{G}_{n}\cdot\mathbf{r}) is 2.25, which gives the coefficient of VSLV_{\mathrm{SL}} to be 4.536 meV. Using the ratio calculated above, we get the coefficient of mean potential to be 64.595 meV. The parameters are then given by

V0(1)=64.595(1−α) VTG+64.595α VSL meVV_{0}^{(1)} = 64.595(1-\alpha)\ V_{\mathrm{TG}} + 64.595\alpha\ V_{\mathrm{SL}}\ \mathrm{meV}
V0(2)=64.595α VTG+64.595(1−α) VSL meVV_{0}^{(2)} = 64.595\alpha\ V_{\mathrm{TG}} + 64.595(1-\alpha)\ V_{\mathrm{SL}}\ \mathrm{meV}
VSL(1)=4.536α VSL meVV_{\mathrm{SL}}^{(1)} = 4.536\alpha\ V_{\mathrm{SL}}\ \mathrm{meV}
VSL(2)=4.536(1−α) VSL meV(3)V_{\mathrm{SL}}^{(2)} = 4.536(1-\alpha)\ V_{\mathrm{SL}}\ \mathrm{meV} \tag*{(3)}

where α\alpha is a screening parameter. It accounts for the asymmetry in the charge induced on each layer due to the gate voltages.

Band structure

Figure S26 and Figure S27 present the evolution of the BLG band structure as a function of the superlattice gate voltage VSLV_{\mathrm{SL}} for two representative choices of the screening parameter α\alpha. Several systematic trends emerge. (i) For both values of α\alpha, the gap at the charge-neutrality point increases as VSLV_{\mathrm{SL}} is varied from 1 to 5 V, accompanied by a clear enhancement of particle–hole asymmetry. (ii) Reversing the sign of VSLV_{\mathrm{SL}} inverts this asymmetry, as seen from the comparison between panels (e) and (f) in both figures. (iii) The band structure—and the size of the gap in particular—is strongly dependent on the choice of α\alpha. A comparison between α=0.51\alpha= 0.51 and α=0.55\alpha= 0.55 shows that, even for a small difference in the value of α\alpha, a substantial difference arises in the resulting gap. Figure S28 shows how the primary (largest) band gap varies as a function of VSLV_{\mathrm{SL}} and VTG−VDV_{\mathrm{TG}} - V_{\mathrm{D}}. At any VSLV_{\mathrm{SL}}, as VTGV_{\mathrm{TG}} decreases, the primary band gap increases. For the remainder of this work, we use α=0.55\alpha= 0.55, which yields a gap consistent with experimental estimates.

Figure S26. Electronic band structures of bilayer graphene (BLG) under different superlattice potentials. (a)–(e) show the band structures for VSL=1V_{\mathrm{SL}} = 1–55 V, and (f) corresponds to VSL=−5V_{\mathrm{SL}} = -5 V, all calculated with the screening parameter α=0.51\alpha= 0.51.

Figure S27. Electronic band structures of bilayer graphene (BLG) under different superlattice potentials. (a)–(e) show the band structures for VSL=1V_{SL}=1–55 V, and (f) corresponds to VSL=−5V_{SL}=-5 V, all calculated with the screening parameter α=0.55\alpha=0.55.

Primary band gap heatmap for α = 0.55

(a)

Primary band gap heatmap for α = 0.51

(b)

Figure S28. Primary band gap plotted as a function of VSLV_{SL} and VTG−VDV_{TG} - V_D for a. α=0.55\alpha= 0.55 b. α=0.51\alpha= 0.51

The chemical potential is obtained from

μ=ℏ2πnm∗(4)\mu= \frac{\hbar^{2}\pi n}{m^{*}} \tag*{(4)}

where nn is the carrier density and m∗=0.05mem^{*} = 0.05m_{\mathrm{e}} is the effective mass.

Resistance Heat Maps

The extreme sensitivity of the band structure to the screening parameter α\alpha naturally leads to a corresponding sensitivity in the calculated resistivity. In Figure S29, we compare the resistance heat maps obtained for α=0.55\alpha= 0.55 and α=0.51\alpha= 0.51. As evident from the figure, the resulting patterns differ substantially. Additional features also appear at larger VSLV_{\mathrm{SL}}, arising from the flattening of the bands and the concomitant opening of higher-order gaps. We also note that incorporating screening requires a self-consistent calculation—particularly in the flat-band regime, where screening effects become dominant and substantially increase the complexity of the problem. Such effects lie beyond the scope of the present work, and our theoretical results should therefore be regarded as providing qualitative support for the experimental evidence.

Resistance heatmap for α = 0.55

(a)

Resistance heatmap for α = 0.51

(b)

Figure S29. Resistance heatmaps for a. α=0.55\alpha= 0.55 b. α=0.51\alpha= 0.51

In constructing the resistance heat maps, the band structures obtained from the electrostatic model (as discussed in the previous subsection) were used as input for the conductivity calculations. While the previous analysis illustrated how the band structure evolves with VSLV_{\mathrm{SL}}, it is important to emphasize that it also varies with the top-gate voltage VTGV_{\mathrm{TG}}. In practice, both the band dispersion and the chemical potential evolve simultaneously as (VTG,VSL)(V_{\mathrm{TG}}, V_{\mathrm{SL}}) are tuned.

To demonstrate this explicitly, we focus on a small region of the resistance heat map in Figure S29 and examine several representative gate-voltage combinations marked I–VI in Figure S30. For each point, we compute the corresponding band structure and determine the position of the chemical potential (indicated by the red dotted line). To identify the regions in momentum space that contribute most significantly to the conductivity, we also highlight the set of kk points satisfying ∣E(k)−μ∣≤5kBT\lvert E(k) - \mu\rvert\leq5k_{\mathrm{B}}T, which depicts the Fermi contour together with its thermal broadening. All calculations are performed at T=2T = 2 K.

Figure S30. Resistance heatmap and the corresponding band structures a. Resistance heatmap for α=0.55\alpha= 0.55. I–III shows the band structures and the Fermi surfaces corresponding to VSL=2V_{\mathrm{SL}} = 2 V, and VTG−VD=−0.25V_{\mathrm{TG}} - V_{\mathrm{D}} = -0.25, −0.3-0.3 and −0.5-0.5 V, which are marked on the heatmap, respectively. Similarly, IV–VI corresponds to VSL=3V_{\mathrm{SL}} = 3 V and VTG−VD=−0.3V_{\mathrm{TG}} - V_{\mathrm{D}} = -0.3, −0.4-0.4, and −0.6-0.6 V, respectively.

A detailed inspection of these six points confirms that both the band structure and the chemical potential vary simultaneously as functions of (VTGV_{TG}, VSLV_{SL}), although their dominant roles differ: changes in VSLV_{SL} primarily reshape the band structure [cf. points I and IV], whereas changes in VTGV_{TG} primarily shift the chemical potential. We first consider points I–III, where VSLV_{SL} is fixed at 2 V and VTGV_{TG} is varied. At point I, the chemical potential lies within the primary band gap and intersects no band, resulting in negligible conductivity (high resistivity). As VTGV_{TG} is decreased to point II, the chemical potential enters the first available band, producing a finite carrier density and giving rise to the narrow low-resistance (blue) region that separates the two insulating domains in Figure S30. The associated Fermi surface contains multiple contributing kk points. A further decrease of VTGV_{TG} shifts the chemical potential into the second band gap, restoring a high-resistivity region in the heat map. Beyond this, the chemical potential drops into a dense manifold of bands, leading to a pronounced increase in conductivity. Points IV–VI correspond to VSL=3V_{SL}=3 V and different values of VTGV_{TG}. The qualitative behaviour mirrors that of the VSL=2V_{SL}=2 V case, but the larger band gap results in the chemical potential entering the first conduction (or valence) band at a smaller value of VTGV_{TG}. Finally, we note the strong sensitivity of the thermally broadened Fermi contour to small variations in gate voltage. For instance, points I and II differ by only −0.05-0.05 V in VTGV_{TG}, yet exhibit markedly different Fermi-surface topologies.

References

References

  1. [1]R. Bistritzer and A. H. MacDonald, Proceedings of the National Academy of Sciences 108, 12233 (2011).
  2. [2]E. Suárez Morell, J. D. Correa, P. Vargas, M. Pacheco, and Z. Barticevic, Phys. Rev. B 82, 121407 (2010).
  3. [3]J. M. B. Lopes dos Santos, N. M. R. Peres, and A. H. Castro Neto, Phys. Rev. B 86, 155449 (2012).
  4. [4]Y. Cao, V. Fatemi, A. Demir, S. Fang, S. L. Tomarken, J. Y. Luo, J. D. Sanchez-Yamagishi, K. Watanabe, T. Taniguchi, E. Kaxiras, et al., Nature 556, 80 (2018).
  5. [5]Y. Cao, V. Fatemi, S. Fang, K. Watanabe, T. Taniguchi, E. Kaxiras, and P. Jarillo-Herrero, Nature 556, 43 (2018).
  6. [6]J. M. Park, Y. Cao, K. Watanabe, T. Taniguchi, and P. Jarillo-Herrero, Nature 590, 249 (2021).
  7. [7]Y. Tang, L. Li, T. Li, Y. Xu, S. Liu, K. Barmak, K. Watanabe, T. Taniguchi, A. H. MacDonald, J. Shan, et al., Nature 579, 353 (2020).
  8. [8]A. Uri, S. Grover, Y. Cao, J. A. Crosse, K. Bagani, D. Rodan-Legrain, Y. Myasoedov, K. Watanabe, T. Taniguchi, P. Moon, et al., Nature 581, 47 (2020).
  9. [9]A. T. Pierce, Y. Xie, J. M. Park, E. Khalaf, S. H. Lee, Y. Cao, D. E. Parker, P. R. Forrester, S. Chen, K. Watanabe, et al., Nature Physics 17, 1210 (2021).
  10. [10]C. N. Lau, M. W. Bockrath, K. F. Mak, and F. Zhang, Nature 602, 41 (2022).
  11. [11]S. Bhownik, A. Ghosh, and U. Chandni, Reports on Progress in Physics 87, 096401 (2024).
  12. [12]H. Zhou, L. Holleis, Y. Saito, L. Cohen, W. Huynh, C. L. Patterson, F. Yang, T. Taniguchi, K. Watanabe, and A. F. Young, Science 375, 774 (2022).
  13. [13]H. Zhou, T. Xie, A. Ghazaryan, T. Holder, J. R. Ehrets, E. M. Spanton, T. Taniguchi, K. Watanabe, E. Berg, M. Serbyn, et al., Nature 598, 429 (2021).
  14. [14]H. Zhou, T. Xie, T. Taniguchi, K. Watanabe, and A. F. Young, Nature 598, 434 (2021).
  15. [15]S. Dubey, V. Singh, A. K. Bhat, P. Parikh, S. Grover, R. Sensarma, V. Tripathi, K. Sengupta, and M. M. Deshmukh, Nano Letters 13, 3990 (2013).
  16. [16]C. Forsythe, X. Zhou, K. Watanabe, T. Taniguchi, A. Pasupathy, P. Moon, M. Koshino, P. Kim, and C. R. Dean, Nature Nanotechnology 13, 566 (2018).
  17. [17]Y. Li, S. Dietrich, C. Forsythe, T. Taniguchi, K. Watanabe, P. Moon, and C. R. Dean, Nature Nanotechnology 16, 525 (2021).
  18. [18]J. Sun, S. A. Akbar Ghorashi, K. Watanabe, T. Taniguchi, F. Camino, J. Cano, and X. Du, Nano Letters 24, 13600 (2024).
  19. [19]R. Huber, M.-H. Liu, S.-C. Chen, M. Drienovsky, A. Sandner, K. Watanabe, T. Taniguchi, K. Richter, D. Weiss, and J. Fromm, Nano letters 20, 8046 (2020).
  20. [20]S. Wang, Z. Zhan, X. Fan, Y. Li, P. A. Pantaleón, C. Ye, Z. He, L. Wei, L. Li, F. Guinea, S. Yuan, and C. Zeng, Phys. Rev. Lett. 133, 066302 (2024).
  21. [21]X. Cai, F. Ren, Q. Li, Y. Shi, Y. Wang, Y. Zhang, Z. Zhi, J. Luo, Y. Chen, J. Liu, et al., Advanced Materials 38, e22185 (2026).
  22. [22]J. Gu, J. Zhu, P. Knuppel, K. Watanabe, T. Taniguchi, J. Shan, and K. F. Mak, Nature Materials 23, 219 (2024).
  23. [23]Z. Zhang, J. Xie, W. Zhao, R. Qi, C. Sanborn, S. Wang, S. Kahn, K. Watanabe, T. Taniguchi, A. Zettl, et al., Nature Materials 23, 189 (2024).
  24. [24]X. Wang, C. Xu, S. Aronson, D. Bennett, N. Paul, P. J. Crowley, C. Collignon, K. Watanabe, T. Taniguchi, R. Ashoori, et al., Nature Communications 16, 178 (2025).
  25. [25]S. A. A. Ghorashi, A. Dunbrack, A. Abouelkomsan, J. Sun, X. Du, and J. Cano, Phys. Rev. Lett. 130, 196201 (2023).
  26. [26]L. Holleis, C. L. Patterson, Y. Zhang, Y. Vituri, H. M. Yoo, H. Zhou, T. Taniguchi, K. Watanabe, E. Berg, S. Nadj-Perge, et al., Nature Physics 21, 444 (2025).
  27. [27]Y. Zhang, R. Polski, A. Thomson, É. Lantagne-Hurtubise, C. Lewandowski, H. Zhou, K. Watanabe, T. Taniguchi, J. Alicea, and S. Nadj-Perge, Nature 613, 268 (2023).
  28. [28]A. M. Seiler, F. R. Geisenhof, F. Winterer, K. Watanabe, T. Taniguchi, T. Xu, F. Zhang, and R. T. Weitz, Nature 608, 298 (2022).
  29. [29]Y. Zeng, T. M. R. Wolf, C. Huang, N. Wei, S. A. A. Ghorashi, A. H. MacDonald, and J. Cano, Phys. Rev. B 109, 195406 (2024).
  30. [30]X. Liu, Z. Hao, E. Khalaf, J. Y. Lee, Y. Ronen, H. Yoo, D. Haei Najafabadi, K. Watanabe, T. Taniguchi, A. Vishwanath, et al., Nature 583, 221 (2020).
  31. [31]H. Polshyn, J. Zhu, M. A. Kumar, Y. Zhang, F. Yang, C. L. Tschirhart, M. Serlin, K. Watanabe, T. Taniguchi, A. H. MacDonald, et al., Nature 588, 66 (2020).
  32. [32]S. Xu, M. M. Al Ezzi, N. Balakrishnan, A. Garcia-Ruiz, B. Tsim, C. Mullan, J. Barrier, N. Xin, B. A. Piot, T. Taniguchi, et al., Nature Physics 17, 619 (2021).
  33. [33]T. Taychatanapat and P. Jarillo-Herrero, Phys. Rev. Lett. 105, 166601 (2010).
  34. [34]M. Sui, G. Chen, L. Ma, W.-Y. Shan, D. Tian, K. Watanabe, T. Taniguchi, X. Jin, W. Yao, D. Xiao, et al., Nature Physics 11, 1027 (2015).
  35. [35]E. Icking, L. Banszerus, F. Wörtche, F. Volmer, P. Schmidt, C. Steiner, S. Engels, J. Hesselmann, M. Goldsche, K. Watanabe, et al., Advanced Electronic Materials 8, 2200510 (2022).
  36. [36]Y. Kim, P. Herlinger, P. Moon, M. Koshino, T. Taniguchi, K. Watanabe, and J. H. Smet, Nano Letters 16, 5053 (2016).
  37. [37]S. Wu, Z. Zhang, K. Watanabe, T. Taniguchi, and E. Y. Andrei, Nature Materials 20, 488 (2021).
  38. [38]S. Bhowmik, B. Ghawri, N. Leconte, S. Appalakondaiah, M. Pandey, P. S. Mahapatra, D. Lee, K. Watanabe, T. Taniguchi, J. Jung, et al., Nature Physics 18, 639 (2022).
  39. [39]S. Bhowmik, B. Ghawri, Y. P. D. Lee, S. Datta, R. Soni, K. Watanabe, T. Taniguchi, A. Ghosh, J. Jung, et al., Nature Communications 14, 4055 (2023).
  40. [40]E. McCann and M. Koshino, Reports on Progress in Physics 76, 056503 (2013).
  41. [41]K. Zou and J. Zhu, Phys. Rev. B 82, 081407(R) (2010).
  42. [42]K. S. Novoselov, E. McCann, S. Morozov, V. I. Fal’ko, M. Katsnelson, U. Zeitler, D. Jiang, F. Schedin, and A. K. Geim, Nature physics 2, 177 (2006).

Paper details

vlnc:W_qqsgkgrc
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents