betaFeedback

WorksPhysics and Astronomy

Anisotropic multiband magnetotransport in LaAg2_2Ge2_2 thin films

Abstract

ThCr2_2Si2_2-type intermetallics are layered conductors in which crystallographic anisotropy and multiband electronic states often give rise to characteristic magnetotransport phenomena. Here, we report the molecular-beam epitaxy growth of LaAg2_2Ge2_2 thin films on MgO(001) and their magnetotransport properties. The Hall effect and magnetoresistance are captured by an effective two-carrier description with a high-mobility electron band, yielding a positive magnetoresistance of 22.5% at 9 T. Angle-dependent magnetoresistance exhibits a dominant twofold anisotropy and additional reproducible dip/peak features at characteristic tilt angles that are nearly independent of field and temperature. These results extend our understanding of the anisotropic electronic transport in thin-film germanides within the ThCr2_2Si2_2 family.

Introduction

ThCr2_2Si2_2-type (122) intermetallics, with general formula AT2X2AT_2X_2, form one of the most extensively studied families of layered compounds [1, 2, 3]. In this structure, T2X2T_2X_2 layers alternate with AA-atom planes along the cc axis, which often yields pronounced electronic anisotropy and a broad range of ground states, including magnetic order [4, 5, 6, 7], unconventional and heavy-fermion superconductivity [8, 9, 10, 11, 12], and nontrivial transport responses [13, 14, 15, 16]. For 122 compounds with XX = Si or Ge, band-structure calculations commonly predict multiple Fermi-surface sheets with different anisotropies, including quasi-two-dimensional and three-dimensional components [17, 18, 19, 20]. Because orbital motion in a magnetic field depends sensitively on field orientation, angle-dependent magnetoresistance can provide a stringent experimental probe of anisotropic and multiband transport to help understand the underlying electronic structure of these compounds.

Epitaxial thin films are well suited for such measurements because a single crystallographic orientation allows the magnetic-field direction to be swept continuously with respect to the principal axes. However, thin-film studies of Si/Ge-based 122 compounds have thus far been limited to heavy fermion compounds such as CeT2_2Ge2_2 (TT = Fe, Ni, or Cu) [21, 22, 23] and YbRh2_2Si2_2 [24, 25], for which only zero-field resistivity has been reported. Systematic magnetotransport measurements that exploit field-angle control in epitaxial 122 films therefore remain scarce. LaAg2_2Ge2_2 crystallizes in the ThCr2_2Si2_2-type structure (space group I4/mmmI4/mmm) [26], with alternating La and Ag2_2Ge2_2 layers along the cc axis [Figure 1(a)]. Because La3+^{3+} has no 4f4f electrons, magnetic scattering and Kondo effects are absent, making LaAg2_2Ge2_2 an ideal system for isolating intrinsic charge-carrier transport. To date, investigations have been limited to bulk polycrystalline samples [26, 27]; specific-heat measurements established a nonmagnetic ground state, but electronic-transport properties have not been reported.

Crystal structure and growth phase diagram of LaAg2Ge2

Figure 1. (a) Crystal structure of LaAg2_2Ge2_2 drawn with VESTA [28]. (b) Growth phase diagram of LaAg2_2Ge2_2 films on MgO(001) substrates. The diagram is mapped as a function of the growth temperature TgT_{\mathrm{g}} and the flux ratio PAg/PGeP_{\mathrm{Ag}}/P_{\mathrm{Ge}} and is classified into four regions: (1) coexistence of LaAg2_2Ge2_2 and LaGe2−x_{2-x} phases, (2) single-phase LaAg2_2Ge2_2, (3) coexistence of polycrystalline LaAg2_2Ge2_2 and Ag, and (4) polycrystalline LaAg2_2Ge2_2.

In this work, we report the synthesis of LaAg2_2Ge2_2 thin films grown on MgO(001) substrates and their unique magnetotransport properties. By utilizing the single-orientation nature of the films, we probe the intrinsic transport anisotropy and multiband features via angle-dependent magnetoresistance ratio (ADMR) and Hall measurements. Our study demonstrates the feasibility of growing high-quality 122-type germanide films and provides a baseline for understanding the charge-carrier transport in this material class.

Experimental Details

LaAg2_2Ge2_2 thin films were synthesized using a molecular beam epitaxy (MBE) system with a base pressure of ∼10−10\sim10^{-10} mbar on MgO(001) substrates that were laser-annealed to optimize surface quality [29, 30, 31]. The in-plane lattice mismatch between LaAg2_2Ge2_2 [26] and MgO is 2.9%. The growth temperature and beam equivalent pressures, measured by an ionization gauge, were tuned to obtain single-phase films. The film thickness was typically 32 nm, corresponding to a growth rate of approximately 0.045 Å/s. To protect the films from degradation in air, all samples not examined by atomic force microscopy were capped in situ with an amorphous Ge layer (≈\approx5 nm) deposited at room temperature.

Structural properties of the films were characterized by X-ray diffraction (XRD) (Smart-Lab, Rigaku). Surface morphology of the uncapped film was examined by atomic force microscopy in a N2_2-filled glovebox. Electrical transport measurements above 1.8 K were carried out in Quantum Design DynaCool Physical Properties Measurement Systems (PPMS) equipped with 9 T and 14 T superconducting magnets. The film was cut into a rectangular piece (2 ×\times 5 mm) and contacted with Al wires at six points for simultaneous four-terminal measurements of the longitudinal resistivity (ρxx\rho_{xx}) and the Hall resistivity (ρyx\rho_{yx}). For standard magnetotransport, the magnetic field was applied perpendicular to the film plane; the longitudinal and Hall components were separated by symmetrization and antisymmetrization with respect to the field direction. For ADMR measurements, the magnetic field was rotated in the acac plane from the out-of-plane direction (θ=0∘\theta= 0^\circ, B∥cB \parallel c) to the in-plane direction (θ=90∘\theta= 90^\circ, B∥aB \parallel a) using a sample rotator, while keeping I∥aI \parallel a.

Results and discussion

The growth temperature and the flux ratio between Ag and Ge were systematically varied while maintaining a constant La flux of 1.0×10−81.0 \times10^{-8} mbar, as summarized in Figure 1(b). Under optimized conditions, single-phase LaAg2_2Ge2_2 is confirmed by XRD θ\theta–2θ2\theta scans without impurity peaks (region 2). In contrast, impurity phases appear when the growth conditions deviate from this narrow window. At temperatures above 600 °C and for smaller flux ratios PAg/PGe≲1.2P_{\mathrm{Ag}}/P_{\mathrm{Ge}} \lesssim1.2, a Ge-rich LaGe2−x_{2-x} phase emerges, consistent with Ag deficiency caused by enhanced re-evaporation of Ag at elevated temperatures (region 1). For growth temperatures below 500 °C, polycrystalline LaAg2_2Ge2_2 peaks are observed (regions 3 and 4). This behavior is attributed to insufficient surface diffusion at low temperatures, which suppresses epitaxial ordering and leads to polycrystalline domains. When PAg/PGeP_{\mathrm{Ag}}/P_{\mathrm{Ge}} is increased beyond the optimal range, Ag impurity peaks appear (region 3). Representative XRD θ\theta–2θ2\theta scans for regions 1–4 are provided in Figure S1 of the Supplemental Material [32].

Figure S1. (a) Growth phase diagram of LaAg2Ge2\mathrm{LaAg}_{2}\mathrm{Ge}_{2} films on MgO(001) substrates. The diagram is mapped as a function of the growth temperature TgT_{\mathrm{g}} and the flux ratio PAg/PGeP_{\mathrm{Ag}}/P_{\mathrm{Ge}} and is classified into four regions: (1) coexistence of LaAg2Ge2\mathrm{LaAg}_{2}\mathrm{Ge}_{2} and LaGe2−x\mathrm{LaGe}_{2-x} phases, (2) single-phase LaAg2Ge2\mathrm{LaAg}_{2}\mathrm{Ge}_{2}, (3) coexistence of polycrystalline LaAg2Ge2\mathrm{LaAg}_{2}\mathrm{Ge}_{2} and Ag, and (4) polycrystalline LaAg2Ge2\mathrm{LaAg}_{2}\mathrm{Ge}_{2}. The filled circles indicate the growth conditions for which the XRD data shown in (b) were collected. (b) Representative XRD θ\theta–2θ2\theta scans corresponding to these four regions. Black arrows indicate polycrystalline diffraction peaks of LaAg2Ge2\mathrm{LaAg}_{2}\mathrm{Ge}_{2} other than the (004) and (006) reflections.

Figure 2 shows the structural characterization of a single-phase LaAg2_2Ge2_2 film. The XRD θ\theta–2θ2\theta scan in Figure 2(a) reveals sharp reflections from the {001}\{001\} LaAg2_2Ge2_2 lattice planes without any impurity phases. The out-of-plane lattice parameter along the cc axis is determined to be c=10.920c = 10.920 Å. The full width at half maximum (FWHM) of the rocking curves around the peak of (002) (Figure 2(b)) is about 0.11∘0.11^\circ, indicating the high crystalline quality of the film. The reciprocal-space map in Figure 2(c) yields an in-plane lattice parameter a=4.33a = 4.33 Å,

Figure 2. (a) XRD θ\theta–2θ2\theta scan of a LaAg2_2Ge2_2 film grown on a MgO(001) substrate. MgO substrate peaks are marked with an asterisk. (b) Rocking curve around the (002) LaAg2_2Ge2_2 film peak. (c) Reciprocal space map around the (208) LaAg2_2Ge2_2 film and (204) MgO substrate peaks. The pink cross indicates the peak position expected from bulk polycrystalline lattice parameters [26]. (d) In-plane azimuthal (φ\varphi) scans around LaAg2_2Ge2_2 (208) (top) and MgO (204) (bottom) peaks. (e) Surface morphology of the film, taken by atomic force microscopy.

slightly smaller than the bulk value a=4.3354a = 4.3354 Å [26], while the out-of-plane parameter slightly exceeds the bulk value c=10.914c = 10.914 Å. This tetragonal distortion is consistent with a small compressive in-plane strain imposed by the MgO substrate (aMgO=4.212a_{\mathrm{MgO}} = 4.212 Å). The azimuthal (φ\varphi) scans of the LaAg2Ge2\mathrm{LaAg}_{2}\mathrm{Ge}_{2} (208) and MgO (204) reflections in Figure 2(d) display fourfold symmetry at the same azimuthal positions, confirming single-domain growth with a well-defined in-plane orientation relationship. The atomic force microscopy image in Figure 2(e) shows a terraced morphology with facets aligned along orthogonal directions, reflecting the tetragonal symmetry of LaAg2Ge2\mathrm{LaAg}_{2}\mathrm{Ge}_{2}.

We next discuss the temperature dependence of the longitudinal resistivity ρxx\rho_{\mathrm{xx}} of our films. Figure 3(a) shows the longitudinal resistivity ρxx(T)\rho_{\mathrm{xx}}(T) of the LaAg2Ge2\mathrm{LaAg}_{2}\mathrm{Ge}_{2} film together with previously reported data for single-crystalline bulk samples of LaCu2Ge2\mathrm{LaCu}_{2}\mathrm{Ge}_{2} [33] and LaAu2Ge2\mathrm{LaAu}_{2}\mathrm{Ge}_{2} [34]. Within the measured temperature range and measurement geometry, the LaAg2Ge2\mathrm{LaAg}_{2}\mathrm{Ge}_{2} film exhibits a lower ρxx\rho_{\mathrm{xx}} than these literature data. To gain further insight into the scattering mechanisms governing the resistivity of LaAg2Ge2\mathrm{LaAg}_{2}\mathrm{Ge}_{2}, we analyze the ρxx(T)\rho_{\mathrm{xx}}(T) data

Figure 3. (a) Temperature dependence of the longitudinal resistivity ρxx(T)\rho_{\mathrm{xx}}(T) for LaAg2Ge2\mathrm{LaAg}_{2}\mathrm{Ge}_{2} thin film (present study), compared with previously reported bulk single-crystalline samples of LaCu2Ge2\mathrm{LaCu}_{2}\mathrm{Ge}_{2} [33] and LaAu2Ge2\mathrm{LaAu}_{2}\mathrm{Ge}_{2} [34]. (b) Bloch–Grüneisen–Mott (BGM) fitting of the ρxx(T)\rho_{\mathrm{xx}}(T) data for the LaAg2Ge2\mathrm{LaAg}_{2}\mathrm{Ge}_{2} film. The solid black line shows the experimental ρxx(T)\rho_{\mathrm{xx}}(T) data, while the dashed line represents the temperature-dependent resistivity ρxx(T)−ρ0\rho_{\mathrm{xx}}(T)-\rho_{0} obtained by subtracting the residual resistivity ρ0\rho_{0}. The individual phonon (orange) and Mott (blue) contributions obtained from the BGM model are also shown.

using the Bloch–Grüneisen–Mott (BGM) model [20, 34, 35, 36],

ρxx(T)=ρ0+4ΘDR(TΘD)5∫0ΘD/Tx5 dx(ex−1)(1−e−x)−KT3,(1)\rho_{xx}(T) = \rho_0 + 4\Theta_{\mathrm{D}}R\left(\frac{T}{\Theta_{\mathrm{D}}}\right)^5 \int_0^{\Theta_{\mathrm{D}}/T} \frac{x^5\,\mathrm{d}x}{(e^x-1)(1-e^{-x})} - KT^3, \tag*{(1)}

where ρ0\rho_0 is the residual resistivity. The second term is the Bloch–Grüneisen expression for electron–phonon scattering with an effective phonon cutoff parameter ΘD\Theta_{\mathrm{D}} (commonly used as a transport proxy for the Debye temperature), and RR is the corresponding prefactor. The last term represents the Mott ss–dd interband-scattering contribution, written as ρsd(T)=−KT3\rho_{\mathrm{sd}}(T)=-KT^3; in the fitting procedure, KK is allowed to take either sign to accommodate material-dependent curvature in ρ(T)\rho(T). As shown in Figure 3(b), ρxx(T)\rho_{xx}(T) of LaAg2_2Ge2_2 is well reproduced by the BGM model. The fitted parameters are summarized in Table I and are comparable to those reported for related intermetallic compounds [20]. To assess the importance of the Mott term, it is instructive to compare the temperature-dependent contributions to ρ(T)\rho(T). For LaAg2_2Ge2_2, the extracted KK yields a Mott contribution that remains small compared to the phonon term over the entire measured temperature range, indicating that the resistivity is dominated by electron–phonon scattering up to room temperature.

CompoundRRRρ0\rho_0 (μΩ\mu\Omega cm)ΘD\Theta_{\mathrm{D}} (K)RR (μΩ\mu\Omega cm K−1^{-1})KK (μΩ\mu\Omega cm K−3^{-3})
LaCu2_2Ge2_2 bulk18.77.02220.421.7×10−71.7 \times10^{-7}
LaAg2_2Ge2_2 film9.32.31810.078.8×10−98.8 \times10^{-9}
LaAu2_2Ge2_2 bulk5.619.01260.27−5.8×10−8-5.8 \times10^{-8}

Table I. Transport and phonon parameters extracted from Bloch–Grüneisen–Mott (BGM) analysis for bulk LaCu2_2Ge2_2 [33] and LaAu2_2Ge2_2 [34] and a thin film LaAg2_2Ge2_2 sample.

A systematic trend is observed in the fitted ΘD\Theta_{\mathrm{D}} values, increasing from LaAu2_2Ge2_2 to LaAg2_2Ge2_2 and LaCu2_2Ge2_2 (Table I). While ΘD\Theta_{\mathrm{D}} from BGM fitting should be interpreted as an effective phonon cutoff rather than a thermodynamic Debye temperature, the trend is qualitatively consistent with variations in atomic mass and bonding strength across the series [37]. Within the BGM framework, the high-temperature resistivity is largely governed by the phonon contribution, which depends on both the characteristic phonon scale (ΘD\Theta_{\mathrm{D}}) and the overall coupling strength captured by the prefactor RR. Consistent with this picture, LaCu2_2Ge2_2 exhibits both the largest ΘD\Theta_{\mathrm{D}} and the largest RR in Table I, resulting in a substantially larger ρ(300 K)\rho(300\ \mathrm{K}) than LaAg2_2Ge2_2. Accordingly, although the LaAg2_2Ge2_2 film shows a

small residual resistivity, its comparatively smaller phonon-scattering contribution at high temperature reduces ρ(300 K)\rho(300\,\mathrm{K}) and thus yields a smaller RRR than LaCu2_2Ge2_2. We note that RRR is also sensitive to sample-dependent elastic scattering through ρ0\rho_0; therefore, any apparent correlation between ΘD\Theta_{\mathrm{D}} and RRR should be regarded as qualitative rather than strictly causal. This interpretation is consistent with trends reported for other nonmagnetic LaM2_2Ge2_2 compounds [20].

Figure 4 summarizes the magnetotransport properties of the LaAg2_2Ge2_2 film. Figure 4(a) and Figure 4(b) present the magnetoresistance ratio (MRR ≡ρxx(B)/ρxx(0)−1\equiv\rho_{xx}(B)/\rho_{xx}(0)-1) and Hall resistivity (ρyx\rho_{yx}), respectively, measured at various temperatures. The LaAg2_2Ge2_2 film exhibits a positive magnetoresistance, the magnitude of which increases with decreasing tempera-

Figure 4. Magnetic field (BB) dependence of (a) magnetoresistance ratio (MRR ≡ρxx(B)/ρxx(0)−1\equiv\rho_{xx}(B)/\rho_{xx}(0)-1) and (b) Hall resistivity (ρyx\rho_{yx}) under an out-of-plane magnetic field at a series of temperatures. Temperature dependence of (c) carrier density and (d) mobility as estimated by fits to the two-carrier Drude model. The values at 100 and 300 K are obtained from single-carrier linear fitting.

ture, reaching up to 22.5% at 1.8 K and 9 T. This behavior is consistent with conventional orbital magnetoresistance governed by carrier mobility. At low temperatures, ρyx\rho_{yx} exhibits a pronounced nonlinear field dependence, indicating the coexistence of multiple types of charge carriers. Moreover, both the Hall resistivity and its slope change sign with increasing magnetic field, providing clear evidence for the presence of electrons and holes in LaAg2_2Ge2_2. At higher temperatures, the ρyx\rho_{yx}–BB curves tend to become linear, particularly above 100 K, suggesting that a single type of carrier dominates transport at elevated temperatures.

To quantify the carrier properties, the Hall conductivity σxy\sigma_{xy} was analyzed using a two-carrier Drude model,

σxy(B)=ρyx(B)ρxx2(B)+ρyx2(B)=[nhμh21+(μhB)2−neμe21+(μeB)2]eB,(2)\begin{aligned} \sigma_{xy}(B) &= \frac{\rho_{yx}(B)}{\rho_{xx}^{2}(B)+\rho_{yx}^{2}(B)} \\ &= \left[\frac{n_{\mathrm{h}}\mu_{\mathrm{h}}^{2}}{1+(\mu_{\mathrm{h}}B)^{2}}-\frac{n_{\mathrm{e}}\mu_{\mathrm{e}}^{2}}{1+(\mu_{\mathrm{e}}B)^{2}}\right]eB, \tag*{(2)} \end{aligned}

where nhn_{\mathrm{h}} (nen_{\mathrm{e}}) and μh\mu_{\mathrm{h}} (μe\mu_{\mathrm{e}}) denote the carrier densities and mobilities of holes (electrons), respectively. Figure 4(c) and Figure 4(d) show the temperature dependence of the carrier density and mobility extracted from the two-carrier fits. At 1.8 K, the fitting yields carrier densities of nh=3.7×1023 cm−3n_{\mathrm{h}}=3.7\times10^{23}\ \mathrm{cm}^{-3} for holes and ne=1.9×1019 cm−3n_{\mathrm{e}}=1.9\times10^{19}\ \mathrm{cm}^{-3} for electrons, with corresponding mobilities of μh=7 cm2 V−1s−1\mu_{\mathrm{h}}=7\ \mathrm{cm}^{2}\ \mathrm{V}^{-1}\mathrm{s}^{-1} and μe=2100 cm2 V−1s−1\mu_{\mathrm{e}}=2100\ \mathrm{cm}^{2}\ \mathrm{V}^{-1}\mathrm{s}^{-1}. Electrons exhibit much higher mobility than holes and their density is more than three orders of magnitude smaller. Holes dominate the total carrier density and show only weak temperature dependence.

With increasing temperature, the mobility of the minority electron decreases rapidly, reducing its weight in the total conductivity. Accordingly, the Hall response becomes nearly linear above 100 K and can be described by an effective single-carrier picture. While the two-carrier Drude parameters should be regarded as effective quantities, the analysis robustly indicates the coexistence of opposite-sign carriers and, in particular, a high-mobility minority electron contribution at low temperatures. Such a high-mobility component enhances the orbital magnetoresistance and is consistent with the observed positive magnetoresistance.

We measured the field-angle dependence of ρxx\rho_{xx} to characterize anisotropic magnetotransport in the epitaxial LaAg2_2Ge2_2 film (Figure 5). The ADMR was obtained by rotating the magnetic field from the out-of-plane direction (θ=0∘\theta=0^\circ, B∥cB\parallel c) toward the in-plane direction (θ=90∘\theta=90^\circ, B∥aB\parallel a), with the transport current applied along the aa axis. Figure 5(a) shows the ADMR at T=1.8T=1.8 K for several magnetic fields. A pronounced twofold angular modulation is observed, with minima at θ=90∘\theta=90^\circ and 270∘270^\circ (field in the film plane). At B=14B=14 T the ADMR reaches 24%, and its amplitude decreases monotonically with decreasing field while the overall angular profile is largely preserved. Figure 5(b) displays the temperature evolution at a fixed field of 14 T: the ADMR is gradually suppressed upon warming, consistent with reduced carrier mobility, whereas the twofold symmetry persists over the entire temperature range.

Figure 5. Angle-dependent magnetoresistance ratio (ADMR), defined as ADMR ≡ρxx(θ)/ρxx(90∘)−1\equiv\rho_{xx}(\theta)/\rho_{xx}(90^\circ)-1, measured with I∥aI \parallel a while rotating BB in the acac plane. (a) Field dependence at T=1.8T=1.8 K. (b) Temperature dependence at B=14B=14 T. The inset in (a) illustrates the measurement geometry: the field angle θ\theta is measured from the film normal [001][001], so that θ=0∘\theta=0^\circ corresponds to B∥cB \parallel c and θ=90∘\theta=90^\circ to B∥aB \parallel a.

In addition to the dominant twofold component, fine structure appears near θ≈0∘\theta\approx0^\circ and 180∘180^\circ in the low-temperature, high-field regime. Although experimental factors such

as a small angular misalignment or a weak Hall admixture could, in principle, produce a fixed-angle artifact, the dip/peak features are reproducible and ρxx(θ)\rho_{xx}(\theta) exhibits θ→θ+180∘\theta\to\theta+ 180^\circ symmetry, supporting an intrinsic origin. Specifically, dip features are observed near θ≃0∘\theta\simeq0^\circ and 20∘20^\circ, accompanied by peak features near θ≃7∘\theta\simeq7^\circ and 31∘31^\circ. These dip/peak angles remain essentially unchanged over the investigated field and temperature ranges, while their amplitudes grow with increasing field and decreasing temperature. The nearly field- and temperature-independent angular positions suggest that these features are set primarily by Fermi-surface geometry, as expected for an orbital magnetotransport effect governed by the Fermi-surface anisotropy. A plausible interpretation is a multiband ADMR response arising from the coexistence of Fermi-surface sheets with different anisotropies (e.g., three-dimensional and quasi-two-dimensional components), which can generate extrema at characteristic tilt angles set by the Fermi-surface geometry [38, 39, 40, 41, 42]. Possible alternative mechanisms, such as Yamaji oscillations [43] and Lebed magic-angle resonances [44, 45, 46], are discussed further in the Supplemental Material (Figure S3) [32].

Figure S3. Expanded view of the angle-dependent magnetoresistance ratio ADMR[0°] ≡ ρxx(θ)/ρxx(0∘)−1\rho_{xx}(\theta)/\rho_{xx}(0^\circ)-1 in the vicinity of θ=180∘\theta= 180^\circ. (a) Field dependence at T=1.8T = 1.8 K. (b) Temperature dependence at B=14B = 14 T. The angular positions of the features are independent of field and temperature.

Conclusion

We have grown LaAg2_2Ge2_2 on MgO (001) thin films by MBE and characterized their structural and magnetotransport properties. The films exhibit metallic conduction and a positive transverse magnetoresistance reaching 22.5% at 1.8 K and B=9B = 9 T. The low-temperature Hall nonlinearity is well described by a two-carrier model, revealing the coexistence of electron and hole contributions with strongly different mobilities, including a high-mobility minority electron. ADMR measurements show a robust twofold anisotropy and, at low temperatures and high fields, additional dip/peak structures at specific field angles whose positions are insensitive to field strength and temperature, consistent with a Fermi-surface-related anisotropic magnetotransport response in this 122 germanide. These results establish Ag–Ge-based 122 epitaxial films as a practical platform for controlled-orientation magnetotransport studies and motivate extensions to magnetically and electronically active 122 analogues.

Acknowledgments

We acknowledge funding provided by the Institute for Quantum Information and Matter, a NSF Physics Frontiers Center (NSF Grant PHY-2317110) and the Gordon and Betty Moore Foundation’s EPiQS Initiative (Grant number GBMF10638). We acknowledge the support of JSPS Overseas Research Fellowships. This material is based upon work supported by the National Science Foundation Graduate Research Fellowship Program under Grant No. 2139433 (RD, VS). Any opinions, findings,and conclusions or recommendations expressed in this material are those of the author(s) and do not necessarily reflect the views of the National Science Foundation.

References

Supplementary Materials

Optimization of growth conditions

We optimized the growth conditions by supplying La, Ag, and Ge fluxes onto MgO(001) substrates. The growth temperature and the flux ratio between Ag and Ge were systematically varied while maintaining a constant La flux of 1.0×10−81.0 \times10^{-8} mbar, as summarized in Figure S1.

When the flux ratio and substrate temperature are optimized (PAg=1.2×10−8P_{\mathrm{Ag}} = 1.2 \times10^{-8} mbar, PGe=0.9×10−8P_{\mathrm{Ge}} = 0.9 \times10^{-8} mbar, and Tg=600 ∘CT_{\mathrm{g}} = 600\,^\circ\mathrm{C}), a single-phase LaAg2_2Ge2_2 film is confirmed by XRD θ\theta–2θ2\theta scans without any impurity peaks (region 2).

In contrast, impurity phases appear when the growth conditions deviate from this narrow window. At temperatures above 600 ∘C600\,^\circ\mathrm{C} and for smaller flux ratios PAg/PGe≲1.2P_{\mathrm{Ag}}/P_{\mathrm{Ge}} \lesssim1.2, a Ge-rich LaGe2−x_{2-x} phase emerges, indicating Ag deficiency caused by enhanced re-evaporation of Ag at elevated temperatures (region 1). For growth temperatures below 500 ∘C500\,^\circ\mathrm{C}, polycrystalline LaAg2_2Ge2_2 peaks are observed (regions 3 and 4). This behavior is attributed to insufficient surface diffusion of adatoms at low temperatures, which suppresses epitaxial ordering and leads to the formation of polycrystalline domains. When the PAg/PGeP_{\mathrm{Ag}}/P_{\mathrm{Ge}} ratio is increased beyond the optimal range, Ag impurity peaks appear, corresponding to region 3.

Structural characterization

Figure S2 provides additional structural characterization of the LaAg2Ge2\mathrm{LaAg}_{2}\mathrm{Ge}_{2} film. The in-plane lattice mismatch between LaAg2Ge2\mathrm{LaAg}_{2}\mathrm{Ge}_{2} [26] and MgO is 2.9%, as illustrated in Figure S2. The in situ reflection high-energy electron diffraction (RHEED) patterns acquired after growth are shown in Figure S2 and Figure S2 for φ=0∘\varphi= 0^{\circ} and 45∘45^{\circ}, respectively. Both patterns exhibit sharp streaks, indicating a smooth surface morphology and well-ordered in-plane crystallinity of the LaAg2Ge2\mathrm{LaAg}_{2}\mathrm{Ge}_{2} film.

Crystal structures, RHEED patterns, and reciprocal-space mappings of LaAg₂Ge₂ and MgO

Figure S2. (a) Crystal structures of the LaAg2_2Ge2_2 film and the MgO substrate viewed along the out-of-plane direction. The angle φ\varphi is defined as the angle between the incident electron beam and the crystallographic aa axis, as used in panels (b)–(e). In situ RHEED patterns acquired after growth for (b) φ=0∘\varphi= 0^\circ and (c) φ=45∘\varphi= 45^\circ. (d) Extended reciprocal-space mapping measured along the h=2h = 2 rod at φ=0∘\varphi= 0^\circ and (e) along the h=k=1h = k = 1 rod at φ=45∘\varphi= 45^\circ. The relative intensities of the four LaAg2_2Ge2_2 diffraction peaks are consistent with those calculated from the bulk crystal structure [26].

Extended reciprocal-space mappings are presented in Figure S2 and Figure S2. At φ=0∘\varphi= 0^{\circ}, diffraction peaks corresponding to the LaAg2Ge2\mathrm{LaAg}_{2}\mathrm{Ge}_{2} (2 0 10) and (208) reflections are clearly observed along the h=2h = 2 rod, together with the MgO (204) substrate peak. This confirms that the aa and bb axes of the LaAg2Ge2\mathrm{LaAg}_{2}\mathrm{Ge}_{2} film are aligned with those of the MgO substrate, as illustrated in Figure S2. At φ=45∘\varphi= 45^{\circ}, the LaAg2Ge2\mathrm{LaAg}_{2}\mathrm{Ge}_{2} (1 1 10) and (118) reflections appear along the h=k=1h = k = 1 rod, confirming the fourfold in-plane symmetry of the film. The relative intensities of the observed LaAg2Ge2\mathrm{LaAg}_{2}\mathrm{Ge}_{2} diffraction peaks are consistent with those calculated from the bulk crystal structure, indicating that the film preserves its intrinsic crystallographic symmetry.

Origin of the dip/peak structure in the angle-dependent magnetoresistance ratio (ADMR)

To clarify the origin of the dip-and-peak structures observed around 180° in the ADMR of LaAg2_2Ge2_2 (Figure S3), we consider three mechanisms known to produce characteristic angular features in the magnetoresistance of metals and semimetals.

Multiband ADMR from coexisting quasi-two-dimensional and three-dimensional Fermi-surface sheets

In compensated multiband systems hosting Fermi-surface sheets of different dimensionality, the angle-dependent magnetoresistance can develop a complex profile with dips and peaks that reflect the distinct angular responses of each carrier pocket. When the field is tilted to specific angles, the relative contributions of different sheets to the total conductivity change, and their competition can produce alternating dip-and-peak structures at angles governed by the Fermi-surface geometry. Such behavior has been reported in the multiband systems ZrSiS [38], NbSb2_2 and TaSb2_2 [39], TiB2_2 [40], and W2_2As3_3 [41, 42], where the interplay between quasi-two-dimensional and more three-dimensional pockets gives rise to nontrivial angular structures in ρxx(θ)\rho_{xx}(\theta). Because LaAg2_2Ge2_2 is a compensated multiband system—as evidenced by the nonlinear Hall resistivity and the two-carrier analysis presented in the main text—a similar multiband origin for the dip-and-peak structures is plausible. In this scenario, the angular positions of the features are determined by the Fermi-surface geometry and are therefore independent of both magnetic-field strength and temperature, consistent with our observations.

Yamaji oscillations

Yamaji oscillations are angular magnetoresistance oscillations (AMRO) characteristic of quasi-two-dimensional metals with a corrugated cylindrical Fermi surface [43]. At specific tilt angles, all cross-sectional orbits on the corrugated cylinder share the same extremal area, producing peaks or dips in the interlayer resistivity ρzz\rho_{zz}. However, Yamaji oscillations are predominantly an interlayer (ρzz\rho_{zz}) phenomenon, whereas the features in LaAg2_2Ge2_2 appear in the in-plane resistivity ρxx\rho_{xx}. Moreover, the Fermi wave vector estimated from the expected Yamaji periodicity, kF=0.64A˚−1k_{\mathrm{F}} = 0.64 \mathring{A}^{-1} (∼88%\sim88\% of kak_a), far exceeds the value consistent with the carrier density obtained from the Hall-effect analysis. A Yamaji-oscillation origin is therefore unlikely.

Lebed magic-angle resonances

Lebed resonances produce sharp features in the angular magnetoresistance of quasi-one-dimensional conductors possessing open Fermi-surface sheets [44, 45, 46]. At field orientations commensurate with the real-space lattice periodicity along the open-orbit direction, the interlayer conductivity is resonantly enhanced, generating dips in ρzz\rho_{zz}. Although arctan⁡(a/c)=21.6∘\arctan(a/c) = 21.6^\circ is close to the angular position of one of the observed dips in LaAg2_2Ge2_2, band-structure calculations for Si- and Ge-based 122 compounds do not reveal quasi-one-dimensional open Fermi-surface sheets [17, 18, 19, 20], and the tetragonal crystal structure is incompatible with the low-dimensional topology required for Lebed resonances. This mechanism is therefore unlikely as well.

On the basis of the above analysis, we conclude that the dip-and-peak structures in the ADMR of LaAg2_2Ge2_2 most likely originate from its multiband electronic structure, in which the coexistence of Fermi-surface pockets with different dimensionalities and anisotropies produces a nontrivial angular profile in the in-plane magnetoresistance. This interpretation is consistent with the field- and temperature-independent angular positions of both the dips and peaks, which are dictated by the intrinsic Fermi-surface geometry.

References

  1. [1]Z. Ban and M. Sikirica, Acta Crystallogr. 18, 594 (1965).
  2. [2]R. Hoffmann and C. Zheng, J. Phys. Chem. 89, 4175 (1985).
  3. [3]M. Shatruk, J. Solid State Chem. 272, 198 (2019).
  4. [4]G. Huan, M. Greenblatt, and M. Croft, Eur. J. Solid State Inorg. Chem. 26, 193 (1989).
  5. [5]A. Szytula and J. Leciejewicz, Handbook on the Physics and Chemistry of Rare Earths, Vol. 12 (Elsevier, 1989) pp. 133–211.
  6. [6]Y. Luo, J. Bao, C. Shen, J. Han, X. Yang, C. Lv, Y. Li, W. Jiao, B. Si, C. Feng, J. Dai, G. Cao, and Z.-a. Xu, Phys. Rev. B 86, 245130 (2012).
  7. [7]X. Tan, Z. P. Tener, and M. Shatruk, Acc. Chem. Res. 51, 230 (2018).
  8. [8]F. Steglich, J. Aarts, C. D. Bredl, W. Lieke, D. Meschede, W. Franz, and H. Schäfer, Phys. Rev. Lett. 43, 1892 (1979).
  9. [9]M. Rotter, M. Tegel, and D. Johrendt, Phys. Rev. Lett. 101, 107006 (2008).
  10. [10]S. Khim, J. F. Landaeta, J. Banda, N. Bannor, M. Brando, P. M. R. Brydon, D. Hafner, R. Küchler, R. Cardoso-Gil, U. Stockert, A. P. Mackenzie, D. F. Agterberg, C. Geibel, and E. Hassinger, Science 373, 1012 (2021).
  11. [11]J. A. Mydosh, P. M. Oppeneer, and P. S. Riseborough, J. Phys. Condens. Matter. 32, 143002 (2020).
  12. [12]K. Nogaki, A. Daido, J. Ishizuka, and Y. Yanase, Phys. Rev. Research 3, L032071 (2021).
  13. [13]W. Peng, S. Chanakian, and A. Zevalkink, Inorg. Chem. Front. 5, 1744 (2018).
  14. [14]H. Su, X. Shi, W. Xia, H. Wang, X. Hanli, Z. Yu, X. Wang, Z. Zou, N. Yu, W. Zhao, G. Xu, and Y. Guo, Phys. Rev. B 101, 205138 (2020).
  15. [15]S. Malick, A. B. Sarkar, A. Laha, M. Anas, V. K. Malik, A. Agarwal, Z. Hossain, and J. Nayak, Phys. Rev. B 106, 075105 (2022).
  16. [16]M. K. Hooda, A. Chakraborty, S. Roy, R. Swami, A. Agarwal, P. Mandal, S. N. Sarangi, D. Samal, V. P. S. Awana, and Z. Hossain, J. Alloys Compd. 1010, 178130 (2025).
  17. [17]G. Zwicknagl, J. Low Temp. Phys. 147, 123 (2007).
  18. [18]N. Duc Dung, T. D. Matsuda, S. Ikeda, E. Yamamoto, Y. Haga, Y. Takeda, T. Endo, Y. Doi, R. Settai, H. Harima, and Y. Ōnuki, J. Phys. Soc. Jpn. 77, 094702 (2008).
  19. [19]A. Yasui, S.-I. Fujimori, I. Kawasaki, T. Okane, Y. Takeda, Y. Saitoh, H. Yamagami, A. Sekiyama, R. Settai, T. D. Matsuda, Y. Haga, and Y. Ōnuki, Phys. Rev. B 84, 195121 (2011).
  20. [20]K. Ciesielski, G. Chajewski, M. Samsel–Czekala, A. Hackemer, P. Obstarczyk, A. P. Pikul, and D. Kaczorowski, Solid State Commun. 280, 13 (2018).
  21. [21]G. Holter and H. Adrian, Solid State Commun. 58, 45 (1986).
  22. [22]B. Schmied, G. Fecher, C. Schneider, and G. Schönhense, Appl. Phys. A: Mater. Sci. Process. 66, 385 (1998).
  23. [23]Y. S. Li, M. Zheng, B. Mulcahy, L. H. Greene, and J. N. Eckstein, Appl. Phys. Lett. 99, 042507 (2011).
  24. [24]L. Prochaska, X. Li, D. C. MacFarland, A. M. Andrews, M. Bonta, E. F. Bianco, S. Yazdi, W. Schrenk, H. Detz, A. Limbeck, Q. Si, E. Ringe, G. Strasser, J. Kono, and S. Paschen, Science 367, 285 (2020).
  25. [25]E. Bakali, W. Artner, M. Beiser, J. Bernardi, H. Detz, G. Eguchi, A. Foelske, M. Giparakis, C. Herzig, A. Limbeck, H. Nguyen, L. Prochaska, A. Prokofiev, M. Sauer, S. Schwarz, W. Schrenk, G. Strasser, R. Svagera, M. Taupin, A. S. Thirsfeld, M. Waas, X. Yan, D. A. Zocco, A. M. Andrews, and S. Paschen, J. Cryst. Growth 595, 126804 (2022).
  26. [26]C. Benndorf, H. Eckert, and R. Pöttgen, Z. Kristallogr. Cryst. Mater. 239, 239 (2024).
  27. [27]A. Thamizhavel, R. Kulkarni, and S. K. Dhar, Phys. Rev. B 75, 144426 (2007).
  28. [28]K. Momma and F. Izumi, J. Appl. Crystallogr. 44, 1272 (2011).
  29. [29]A. Llanos, S. Salmani-Rezaie, J. Kim, N. Kioussis, D. A. Muller, and J. Falson, Cryst. Growth Des. 24, 115 (2024).
  30. [30]A. Llanos, G. Campisi, V. Show, J. Kim, R. Dorrian, S. Salmani-Rezaie, N. Kioussis, and J. Falson, Nano Lett. 24, 8518 (2024).
  31. [31]R. Dorrian, J. Kim, M. Ohno, A. Llanos, V. Show, N. Kioussis, and J. Falson, Nano Lett. 25, 11427 (2025).
  32. [32]See Supplemental Material for detailed film characterization and a discussion of the angle-dependent magnetoresistance.
  33. [33]H. Mendpara, D. A. Joshi, A. K. Nigam, and A. Thamizhavel, J. Magn. Magn. Mater. 377, 325 (2015).
  34. [34]D. A. Joshi, A. K. Nigam, S. K. Dhar, and A. Thamizhavel, J. Magn. Magn. Mater. 322, 3363 (2010).
  35. [35]J. M. Ziman, Electrons and Phonons: The Theory of Transport Phenomena in Solids (Oxford University Press, 2001) reprint ed.
  36. [36]A. Bid, A. Bora, and A. K. Raychaudhuri, Phys. Rev. B 74, 035426 (2006).
  37. [37]G. R. Stewart, Rev. Sci. Instrum. 54, 1 (1983).
  38. [38]M. N. Ali, L. M. Schoop, C. Garg, J. M. Lippmann, E. Lara, B. Lotsch, and S. S. P. Parkin, Sci. Adv. 2, e1601742 (2016).
  39. [39]Z. Yuan, H. Lu, Y. Liu, J. Wang, and S. Jia, Phys. Rev. B 93, 184405 (2016).
  40. [40]M. Cheng, L. Liu, Y. Zhao, Y. Deng, R. Lv, R. Lan, N. Zhou, Y. Pan, W. Song, Y. Han, X. Luo, and Y. Sun, Mater. Today Phys. 53, 101690 (2025).
  41. [41]L. Zhao, J. He, D. Chen, S. Zhang, Z. Ren, and G. Chen, Phys. Rev. B 99, 205116 (2019).
  42. [42]J. Wang, H. Yang, L. Ding, W. You, C. Xi, J. Cheng, Z. Shi, C. Cao, Y. Luo, Z. Zhu, J. Dai, M. Tian, and Y. Li, npj Quantum Mater. 4, 58 (2019).
  43. [43]K. Yamaji, J. Phys. Soc. Jpn. 58, 1520 (1989).
  44. [44]A. G. Lebed and P. Bak, Phys. Rev. Lett. 63, 1315 (1989).
  45. [45]T. Osada, S. Kagoshiima, and N. Miura, Phys. Rev. B 46, 1812 (1992).
  46. [46]K. Maki, Phys. Rev. B 45, 5111 (1992).

Paper details

vlnc:W_qufcjd5n
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents