betaFeedback

WorksPhysics and Astronomy

High Photovoltaic Efficiency in Bulk-Stacked One-Dimensional GeSe2_{2} van der Waals Crystal

Abstract

Germanium diselenide (GeSe2_{2}) has recently attracted substantial interest as a rare example of one-dimensional (1D) van der Waals material. Here, we investigate the photovoltaic potential of bulk-stacked GeSe2_{2} chains using first-principles calculations within the GW0GW0 approximation and the Bethe-Salpeter equation (BSE) to capture quasiparticle and excitonic effects. The bulk GeSe2_{2} exhibits indirect GW band gaps of 1.92 eV (type-I) and 1.08 eV (type-II). Optical calculations show markedly stronger visible-light absorption in type-II, yielding a spectroscopically limited maximum efficiency (SLME) of ~25.6% at a 0.5 μμm thickness. Phonon and room-temperature ab initio molecular dynamics analyses indicate that type-II is dynamically stable, whereas type-I shows imaginary phonon modes, suggesting a propensity for structural distortion. These results identify type-II GeSe2 as a promising stable absorber for thin-film photovoltaics with enhanced flexibility compared to typical 2D vdW systems.

Introduction

In the past decade, van der Waals (vdW) low-dimensional materials have attracted widespread attention because their intrinsic electronic, optical, and topological properties differ markedly from those of conventional three-dimensional (3D) bulk compounds [6, 7, 8] [1, 2, 3, 4, 5]. Unlike 3D solids, where strong covalent or ionic bonds dominate, vdW systems consist of discrete building blocks such as two-dimensional (2D) layers or one-dimensional (1D) chains held together by relatively weak inter-component forces known as vdW interactions [9, 10, 11, 12, 13, 14, 15, 16]. This weak vdW binding makes it possible to exfoliate individual sheets or chains [8] and to stack different layers with atomic precision [17, 18]. These capabilities enable designer heterostructures whose optoelectronic behavior can be tuned on demand [7] [3].

Much of the early work focused on 2D vdW materials, especially graphene [19] and transition metal dichalcogenide monolayers [2]. Recent studies have begun to explore truly 1D vdW crystals that naturally form as isolated chains rather than being carved from a parent-layered bulk [20]. Classic examples such as carbon nanotubes predate graphene and already showcase exceptional mechanical, electrical, and thermal performance [21]. Quasi-1D nanoribbons derived from 2D sheets have also been investigated for nanoelectronics and quantum devices [22]. Intrinsically 1D vdW materials, such as selenium or tellurium chains, also exist, without being synthesized from layered precursors [23]. These materials present new opportunities for fundamental research and technological applications, offering distinct electronic, optical, and topological characteristics not accessible in 2D or 3D frameworks [24].

Germanium diselenide (GeSe2\mathrm{GeSe}_{2}) exemplifies this class of true 1D vdW materials. Each Ge atom coordinates four Se atoms to form a tetrahedral GeSe4\mathrm{GeSe}_{4} unit. The adjacent tetrahedra share a two-Se edge to produce an extended chain-like lattice [25? ]. Recently, an alternative GeSe2\mathrm{GeSe}_{2} chain topology was synthesized inside carbon nanotube templates, demonstrating that GeSe2\mathrm{GeSe}_{2} can adopt multiple 1D conformations at the nanoscale [25? ]. Both the naturally occurring and template-assisted GeSe2\mathrm{GeSe}_{2} chains, which are called type-I and type-II, respectively, exhibit semiconducting behavior. Standard density functional theory (DFT) predicts that the type-I and type-II isolated GeSe2\mathrm{GeSe}_{2} chains possess mean-field bandgaps of about 1.90 and 0.80 eV, respectively [25? ].

However, in 1D systems, reduced screening amplifies many-body effects that are not captured by mean-field DFT. Quasiparticle gaps typically increase when computed using the GW\mathit{GW} approximation [26], and strong excitonic binding can further reshape optical spectra [27]. Since the GeSe2\mathrm{GeSe}_{2} chain gap lies within the solar-spectrum window, these materials could be promising for next-generation photovoltaics [28]. A reliable assessment of their optoelectronic performance requires an accurate treatment of electron–electron interactions.

In this study, we provide a comprehensive computational investigation to demonstrate that the stacked bulk structure of GeSe2\mathrm{GeSe}_{2} chains holds significant potential for photovoltaic applications. Given the reduced dimensionality of the constituent 1D1\mathrm{D} GeSe2\mathrm{GeSe}_{2} chains, an accurate consideration of electron-electron interactions is essential to obtain reliable electronic and optical properties. To address this issue, we perform ab initio many-body perturbation theory calculations within the GW0\mathit{GW}_{0} approximation, which go beyond the limitations of conventional mean-field DFT calculations. This approach provides a more accurate description of quasiparticle excitations and electronic screening effects, both of which play a crucial role in determining the optoelectronic behavior of the material. By analyzing the optical spectra of the GeSe2\mathrm{GeSe}_{2} chains, we further assess their photovoltaic efficiency using the spectroscopically limited maximum efficiency (SLME) metric [29]. Our SLME calculations reveal that the GeSe2\mathrm{GeSe}_{2} chain structure can achieve a photovoltaic efficiency of up to 25.63% when stacked to a thickness of 0.5 μm0.5\ \mu\mathrm{m}. This efficiency is comparable to or even exceeds that of well-established vdW 1D photovoltaic materials, Sb2S3\mathrm{Sb}_{2}\mathrm{S}_{3} and Sb2Se3\mathrm{Sb}_{2}\mathrm{Se}_{3}, [30, 31], highlighting the potential of GeSe2\mathrm{GeSe}_{2}-based nanostructures for future solar energy conversion.

Computational Details

All first-principles calculations were performed using the Vienna Ab initio Simulation Package (VASP) [32, 33] with the projector-augmented wave method (PAW) [34]. The exchange–correlation potential was treated within the generalized gradient approximation (GGA) in the Perdew–Burke–Ernzerhof (PBE) form [35]. We used the DFT-D3 dispersion correction to describe the inter-chain van der Waals interactions [36], and also verified the key results using the revised vdW-DF2 functional with B86R exchange (rev-vdW-DF2, also referred to as vdW-DF2-B86R) [37, 38], where the revised Becke exchange functional (B86R) [39] is adopted for the exchange functional and a non-local correction is described by the second version of nonlocal vdW-DF (vdW-DF2) [40, 41]. A plane-wave energy cutoff of 500 eV was used for expanding the Kohn–Sham wavefunctions. The Brillouin zone (BZ) integrations used the Γ\Gamma-centered 15×15×1515 \times15 \times15 Monkhorst-Pack kk-grid for structural relaxations and total energy calculations. All atomic positions and lattice parameters were relaxed until the residual Hellmann–Feynman forces on each atom were below 0.01 eV/A˚\mathring{\mathrm{A}} and the total energy change between successive ionic steps was less than 10−510^{-5} eV.

Starting from the ground state converged DFT-GGA, the quasiparticle energies were obtained using the single-shot G0W0G_{0}W_{0} approximation with self-consistent update for GG, which is denoted by GW0GW_{0} [42, 43]. In the GW0GW_{0} calculations, 180 bands (occupied and unoccupied) were included to ensure the convergence of the self-energy. The screened Coulomb interaction WW was treated within the plasmon-pole approximation [42], and the dielectric matrix was constructed on an 8×8×88 \times8 \times8 kk-point grid with a plane-wave cutoff of 211 eV for the response-function expansion.

To incorporate excitonic effects in the optical spectra, we solved the Bethe–Salpeter equation (BSE) on top of the GW0GW_{0} quasiparticle energies [44, 45, 46, 47, 48]. The BSE Hamiltonian included the top 12 valence bands and the lowest 8 conduction bands. The electron–hole kernel was constructed using the same 8×8×88 \times8 \times8 kk-point sampling, retaining local-field effects. From the BSE solution, we extracted the imaginary part of the macroscopic dielectric function ε2(ω)\varepsilon_{2}(\omega) for photon energies up to 10.0 eV. The resulting GW0GW_{0}+BSE absorption spectrum was compared to the independent-particle result at the GW0GW_{0} level—denoted by GWGW+RPA—to assess the impact of electron–hole interactions on optical properties [48].

Results and Discussion

Figure 1 shows the atomic structures of two bulk polymorphs of GeSe2_2, each formed by stacking one-dimensional chains via van der Waals forces. In type-I GeSe2_2 (Figure 1(a)), each germanium atom is coordinated to four selenium atoms, forming a GeSe4_4 tetrahedron. Neighboring tetrahedra share a two-selenium edge, resulting in a continuous 1D tetrahedral chain. In contrast, the recently synthesized type-II GeSe2_2 chain is built from pairs of edge-sharing tetrahedra, as shown in Figure 1(b). These pairs repeat along the chain direction by sharing only selenium corners, producing a different connectivity pattern.

Figure 1. (Color online) Atomic configurations of (a,b) type-I bulk GeSe2_2 and (d,e) type-II bulk GeSe2_2. Triclinic primitive unit cells and corresponding lattice vectors a1\mathbf{a}_1 (red), a2\mathbf{a}_2 (green) and a3\mathbf{a}_3 (blue) are illustrated with atomic chains. Corresponding irreducible Brillouin zones (IBZ) are illustrated for (c) type-I and (f) type-II chains. Reciprocal lattice vectors {b1,b2,b3}\{\mathbf{b}_1,\mathbf{b}_2,\mathbf{b}_3\} and high-symmetric points are displayed together. Atomic configurations are drawn by using VESTA [49].

When these 1D chains are assembled into a bulk phase via vdW interactions, both type-I and type-II structures adopt triclinic unit cells. The lattice constants aia_i (i=1,2,3i = 1, 2, 3) and the interaxial angles θij\theta_{ij} between the vectors ai\mathbf{a}_i and aj\mathbf{a}_j are listed in Table I. In each case, the chains run parallel to a3\mathbf{a}_3, and the in-plane lattice constants satisfy a1=a2\mathbf{a}_1 = \mathbf{a}_2. Together, these parameters fully describe the triclinic geometry of the bulk GeSe2_2 phases derived from their respective 1D chains.

Accurate band-gap values are essential for assessing the photovoltaic potential of GeSe2_2. To this end, we computed the band structures of both type-I and type-II bulk GeSe2_2 using

lattice parameterstype-Itype-II
a1a_16.3494 Å7.2645 Å
a2a_26.3494 Å7.2645 Å
a3a_36.3494 Å7.2645 Å
θ12\theta_{12}121.825°117.949°
θ23\theta_{23}86.889°70.191°
θ31\theta_{31}121.799°150.482°

Table 1. Lattice parameters for type-I and type-II bulk GeSe2_2.

three approaches: DFT-GGA, the HSE06 hybrid functional [50, 51], and the GW0GW_0 approximation. Figure 2(a) and (Figure 2b) represent the DFT-GGA and GW0GW_0 band structures for type-I and type-II GeSe2_2, respectively. Both polymorphs have an indirect fundamental gap located between the Γ\Gamma and XX points. The calculated band gaps are summarized in Table II.

Electronic band structures and absorption spectra of bulk type-I and type-II GeSe2

Figure 2. Electronic structure of bulk type-I and type-II GeSe2_2. Electronic band structures computed by DFT-GGA (blue dashed) and GWGW (red solid) approximations for (a) type-I bulk GeSe2_2 and (b) type-II bulk GeSe2_2. Absorption spectra ε2\varepsilon_2 from GWGW + BSE (magenta dashed) and GWGW + RPA (red solid ) for (c) type-I bulk GeSe2_2 and (d) type-II bulk GeSe2_2.

When compared to the DFT-GGA band gaps of isolated 1D GeSe2_2 chains, 1.91 eV for type-I and 0.79 eV for type-II [25], the bulk-stacked structures exhibit significantly smaller gaps at the GGA level as shown in Table II. In particular, type-II bulk GeSe2_2 shows an extremely small GGA gap of 0.09 eV, indicating that 3D stacking enhances dielectric screening and consequently reduces the mean-field gap in comparison to low-dimensional cases.

Advanced calculations beyond the mean-field level yield band gaps larger than the GGA values. Compared to DFT-GGA calculations, HSE06 calculations enhance band gaps by roughly 0.9 eV in both bulk polymorphs. The GW0GW_{0} approximation predicts even larger band gaps. While for type-I GeSe2_{2}, the GW0GW_{0} approximation increases the band gap to 1.92 eV, it produces a gap for type-II GeSe2_{2} (1.08 eV) slightly larger than the HSE06 value (1.00 eV). Figure 2 also shows that many-body corrections push the valence bands downward and the conduction bands upward compared to the mean-field result.

We use GW0GW_{0} quasiparticle energies consistently for subsequent optical analyses. The optical absorption spectra were obtained by solving the Bethe–Salpeter equation (BSE) based on GW0GW_{0} quasiparticle energies [44, 45, 46, 47, 48]. From the BSE solution, we extracted the imaginary part of the dielectric function, ε2(ω)\varepsilon_{2}(\omega), up to photon energies of 10.0 eV. Figure 2(c) and (Figure 2d) compare the absorption spectra obtained with (GWGW+BSE) and without (GWGW+RPA) electron–hole interactions for type-I and type-II GeSe2_{2}. The inclusion of electron–hole coupling through the BSE reveals excitonic features that are absent in GWGW+RPA spectra. For type-I, the GWGW+BSE calculation does not show low-energy excitonic peaks, whereas type-II exhibits a distinct excitonic peak around 2 eV. These results demonstrate that many-body effects are crucial for accurately modeling both the electronic band gaps and the optical response of bulk GeSe2_{2} in the context of photovoltaic applications.

Figure 3(a) and (Figure 3b) depict the calculated absorption coefficients α(ω)\alpha(\omega) of type-I and type-II GeSe2_{2} structures, respectively, overlayed with the standard AM 1.5 solar irradiance spectra [52]. Remarkably, type-II GeSe2_{2} shows a substantially stronger absorption within the visible spectral range (highlighted by gray shading in Figure 3) than its type-I counterpart. This enhanced absorption indicates a superior capability for photovoltaic energy conversion, attributed to optimal electronic transitions directly aligned with the energies of visible photons.

Absorption coefficients and SLME efficiencies of type-I and type-II bulk GeSe2

Figure 3. Absorption coefficients (red solid line) of (a) type-I and (b) type-II bulk GeSe2_2. The solar irradiance spectra, Air Mass 1.5, is shown with gray lines. The gray box specifies the energy range of visible light. The SLME η\eta of (c) type-1 and (d) type-2 bulk GeSe2_2 are drawn as a function of thickness. For thickness 0.5 μ\mum, the values of SLME are explicitly indicated.

To quantitatively assess the photovoltaic potential, we computed the SLME metric [29],

calculation methodtype-Itype-II
DFT+GGA0.80 eV0.09 eV
HSE061.69 eV1.00 eV
GW0GW_{0}1.92 eV1.08 eV

Table 3. Indirect (fundamental) band gap energies EgE_g for type-I and type-II bulk GeSe2_{2} calculated by DFT+GGA, hybrid functional HSE06, and GW0GW_{0} approximations.

which provides realistic efficiency estimates by considering intrinsic optical absorption properties, electron-hole interactions, and recombination mechanisms. Figure 3(c) and (Figure 3d) illustrate the SLME η\eta as a function of absorber thickness LL for both GeSe2_2 types. At a practical device thickness of 0.5 μ\mum, type-I GeSe2_2 demonstrates an SLME of approximately 16.15%, whereas type-II achieves an even higher efficiency of about 25.63%. The notably higher SLME for type-II GeSe2_2 underlines its exceptional promise as a photovoltaic absorber.

The predicted SLME of type-II GeSe2_2 (25.63% at 0.5 μ\mum thickness) places it in the upper range of efficiencies reported in recent SLME-based assessments of lead-free absorbers [29]. Similarly, computational screenings have suggested that some other lead-free candidates, such as layered Si3_3O and delafossite-type Cu2_2ZnSnO4_4, may reach comparably high SLME values [53, 54].

Since GeSe2_2 is a bulk-stacked quasi-1D van der Waals material, a more direct comparison can be made with quasi-1D ribbon/chain chalcogenides such as Sb2Se3\mathrm{Sb}_2\mathrm{Se}_3 and Sb2S3\mathrm{Sb}_2\mathrm{S}_3, which have been widely investigated as thin-film photovoltaic absorbers [30, 31]. In particular, Sb2S3\mathrm{Sb}_2\mathrm{S}_3 and Sb2Se3\mathrm{Sb}_2\mathrm{Se}_3 are reported to exhibit SLME values of approximately 23.5% and 29.0%, respectively, for a 0.5 μm0.5\,\mu\mathrm{m} film thickness [55], indicating that type-II GeSe2\mathrm{GeSe}_2 is competitive within this broader class of quasi-1D van der Waals photovoltaic absorbers.

Having established the excellent photovoltaic efficiency and favorable optoelectronic characteristics of type-II GeSe2\mathrm{GeSe}_2, it is crucial to verify its structural and thermal stability, as practical applications require materials to retain their properties under realistic operating conditions. To this end, we first assessed dynamic stability by calculating the phonon dispersion spectra for type-I and type-II GeSe2\mathrm{GeSe}_2, as shown in Figure 4(a) and (Figure 4b). The phonon dispersion of type-I GeSe2\mathrm{GeSe}_2 exhibits imaginary (negative) frequencies in parts of the Brillouin zone, suggesting dynamical instability and a tendency toward structural distortions. By contrast, type-II GeSe2\mathrm{GeSe}_2 shows no imaginary frequencies across the Brillouin zone, supporting its dynamical stability.

Phonon frequencies and molecular dynamics stability of bulk GeSe₂

Figure 4. Phonon frequencies of (a) type-I and (b) type-II bulk GeSe2\mathrm{GeSe}_2. (c) Total potential energy and temperature as a function of time during canonical MD simulations at 300 K. (d) The final structure at the end of the simulation time of 4 ps (inset).

Although phonon calculations show harmonic structural stability at 0 K, they do not rule out the possibility of structural changes induced by thermal fluctuations at finite temperatures. Thus, to show robust thermal stability of type-II GeSe2\mathrm{GeSe}_{2} structures at room temperature (300 K), we performed the ab initio molecular dynamics (AIMD) simulation [56]. Using the (3×3×3)(3 \times3 \times3) supercell to include 27 formula units, AIMD was performed in the canonical ensemble (constant NVT). We controlled the temperature of the system by using the Nosé-Hoover thermostat [57, 58]. Figure 4(c) and (Figure 4d) show the evolution of total potential energy and temperature over a 4-ps MD trajectory and includes snapshots of the final structures. Although small fluctuations in total potential energy are observed during the MD runs, no structural collapse or significant phase transformations occur, indicating that type-II GeSe2\mathrm{GeSe}_{2} remains thermally stable over the simulated timescale at room temperature. Moreover, analysis of ensemble-averaged MD data confirms the achievement of thermal equilibrium within the simulation timeframe. Overall, these dynamic and thermodynamic stability analyses reinforce the viability of type-II GeSe2\mathrm{GeSe}_{2} as a stable and efficient absorber material suitable for practical photovoltaic applications. These findings provide a robust theoretical basis to guide future experimental validation and optimization of GeSe2\mathrm{GeSe}_{2}-based solar cells.

Conclusion

In conclusion, our computational study identifies bulk-stacked type-II GeSe2\mathrm{GeSe}_{2} as a promising photovoltaic absorber material, highlighting its superior optoelectronic properties and enhanced absorption. Utilizing GW+BSEGW+\mathrm{BSE} calculations, we quantified the quasiparticle band gaps and excitonic effects, demonstrating that type-II GeSe2\mathrm{GeSe}_{2} achieves an SLME of approximately 25.6% at 0.5 μm\mu\mathrm{m} absorber thickness. This efficiency is comparable to or superior to that of the leading emerging 1D photovoltaic materials stacked in bulk, such as Sb2Se3\mathrm{Sb}_{2}\mathrm{Se}_{3} and Sb2S3\mathrm{Sb}_{2}\mathrm{S}_{3}. Crucially, phonon dispersion calculations and room-temperature molecular dynamics simulations confirm that type-II GeSe2\mathrm{GeSe}_{2} phases are dynamically stable and thermodynamically robust, suitable for practical solar-cell applications. These findings underscore the promising potential of GeSe2\mathrm{GeSe}_{2}-based nanostructures as next-generation photovoltaic materials and establish a theoretical foundation for subsequent experimental validation and device integration.

Acknowledgement

S. Kim was supported by the National Research Foundation (NRF) of Korea (Grant no. NRF-2022R1F1A1074670, RS-2024-00410027 and RS-2025-16065427). B.G.J was supported by the National Research Council of Science & Technology (NST) grant by the Korea government (MSIT) (No. CAP25061-000) and the National Supercomputing Center with supercomputing resources, including technical support (KSC-2025-CRE-0367). Y.K. was supported by the National Research Foundation of Korea (NRF) grant funded by the Korea government (MSIT) (Grant no. RS-2025-00553820). Authors thank the computational support from the Center for Advanced Computation (CAC) at Korea Institute for Advanced Study (KIAS).

Conflicts of interest

There are no conflicts to declare.

References

References

  1. [6]K. F. Mak, C. Lee, J. Hone, J. Shan, and T. F. Heinz, Phys. Rev. Lett. 105, 136805 (2010).
  2. [7]A. K. Geim and I. V. Grigorieva, Nature 499, 419 (2013).
  3. [8]K. S. Novoselov, A. K. Geim, S. V. Morozov, D. Jiang, Y. Zhang, S. V. Dubonos, I. V. Grigorieva, and A. A. Firsov, Science 306, 666 (2004).
  4. [9]J. A. Wilson, F. J. Di Salvo, and S. Mahajan, Adv. Phys. 24, 117 (1975).
  5. [10]K. S. Novoselov, A. K. Geim, S. V. Morozov, D. Jiang, Y. Zhang, S. V. Dubonos, I. V. Grigorieva, and A. A. Firsov, Proc. Natl. Acad. Sci. USA 102, 10451 (2005).
  6. [11]M. Chhowalla, H. S. Shin, G. Eda, L.-J. Li, K. P. Loh, and H. G. Zhang, Nat. Chem. 5, 263 (2013).
  7. [12]S. Manzeli, D. Ovchinnikov, D. Pasquier, O. V. Yazyev, and A. Kis, Nat. Rev. Mater. 2, 17033 (2017).
  8. [13]R. H. Friend and A. D. Yoffe, Adv. Phys. 36, 1 (1987).
  9. [14]J. A. Wilson and A. D. Yoffe, Adv. Phys. 18, 193 (1969).
  10. [15]X. Wang, Y. Wen, D. Borges, and J. Xiao, Adv. Funct. Mater. 28, 1802651 (2018).
  11. [16]T. Heine, Acc. Chem. Res. 48, 65 (2015).
  12. [17]C. R. Dean, A. F. Young, I. Meric, C. Lee, L. Wang, S. Sorgenfrei, K. Watanabe, T. Taniguchi, P. Kim, K. L. Shepard, and J. Hone, Nature Nanotechnology 5, 722 (2010).
  13. [18]A. Castellanos-Gomez, R. van Leeuwen, M. Buscema, H. S. J. van der Zant, G. A. Steele, and W. J. Venstra, 2D Materials 1, 011002 (2014).
  14. [19]A. K. Geim and K. S. Novoselov, Nature Materials 6, 183 (2007).
  15. [20]R. Xiang, T. Inoue, Y. Zheng, A. Kumamoto, Y. Qian, Y. Sato, M. Liu, D. Gokhale, J. Guo, K. Hisama, S. Yotsumoto, T. Ogamoto, H. Arai, Y. Kobayashi, H. Zhang, B. Hou, A. Animisov, Y. Miyata, S. Okada, S. Chiashi, Y. Li, J. Kong, E. I. Kauppinen, Y. Ikuhara, K. Suenaga, and S. Maruyama, Science 367, 537 (2020).
  16. [21]S. Iijima, Nature 354, 56 (1991).
  17. [22]Y. Son, M. L. Cohen, and S. G. Louie, Nature 444, 347 (2006).
  18. [23]A. W. Sleight, Journal of Solid State Chemistry 5, 160 (1972).
  19. [24]A. A. Balandin, F. Kargar, T. T. Salguero, and R. K. Lake, Materials Today 55, 74 (2022).
  20. [25]Y. Lee, Y. W. Choi, K. Lee, C. Song, P. Ercius, M. L. Cohen, K. Kim, and A. Zettl, ACS Nano 17, 8734 (2023).
  21. [26]L. Hedin, Physical Review 139, A796 (1965).
  22. [27]C. D. Spataru, S. Ismail-Beigi, L. X. Benedict, and S. G. Louie, Physical Review Letters 92, 077402 (2004).
  23. [28]L. Tsakalakos, J. Balch, J. Fronheiser, Y. Zhang, A. Mrdula, M. Kelzenberg, M. Lewinscheetz, L. Adee, and R. Buhrman, Applied Physics Letters 91, 233117 (2007).
  24. [29]L. Yu and A. Zunger, Phys. Rev. Lett. 108, 068701 (2012).
  25. [30]R. Kondrotas, C. Chen, and J. Tang, Joule 2, 857 (2018).
  26. [31]A. Mavlonov, T. Razykov, F. Raziq, J. Gan, J. Chantana, Y. Kawano, T. Nishimura, H. Wei, A. Zakutayev, T. Minemoto, X. Zu, S. Li, and L. Qiao, Solar Energy 201, 227 (2020).
  27. [32]G. Kresse and J. Furthmüller, Physical Review B 54, 11169 (1996).
  28. [33]G. Kresse and D. Joubert, Physical Review B 59, 1758 (1999).
  29. [34]P. E. Blöchl, Physical Review B 50, 17953 (1994).
  30. [35]J. P. Perdew, K. Burke, and M. Ernzerhof, Physical Review Letters 77, 3865 (1996).
  31. [36]S. Grimme, J. Antony, S. Ehrlich, and H. Krieg, The Journal of Chemical Physics 132, 154104 (2010).
  32. [37]I. Hamada, Phys. Rev. B 89, 121103 (2014).
  33. [38]H.-J. Kim, S.-H. Kang, I. Hamada, and Y.-W. Son, Phys. Rev. B 95, 180101 (2017).
  34. [39]A. D. Becke, The Journal of Chemical Physics 85, 7184 (1986).
  35. [40]M. Dion, H. Rydberg, E. Schröder, D. C. Langreth, and B. I. Lundqvist, Phys. Rev. Lett. 92, 246401 (2004).
  36. [41]K. Lee, E. D. Murray, L. Kong, B. I. Lundqvist, and D. C. Langreth, Phys. Rev. B 82, 081101 (2010).
  37. [42]M. S. Hybertsen and S. G. Louie, Physical Review B 34, 5390 (1986).
  38. [43]M. Shishkin and G. Kresse, Physical Review B 74, 035101 (2006).
  39. [44]M. Rohlfing and S. G. Louie, Physical Review Letters 81, 2312 (1998).
  40. [45]S. Albrecht, L. Reining, R. Del Sole, and G. Onida, Physical Review Letters 80, 4510 (1998).
  41. [46]M. Rohlfing and S. G. Louie, Physical Review B 62, 4927 (2000).
  42. [47]G. Onida, L. Reining, and A. Rubio, Reviews of Modern Physics 74, 601 (2002).
  43. [48]L. X. Benedict, E. L. Shirley, and A. H. MacDonald, Physical Review Letters 80, 4514 (1999).
  44. [49]K. Momma and F. Izumi, Journal of Applied Crystallography 44, 1272 (2011).
  45. [50]J. Heyd, G. E. Scuseria, and M. Ernzerhof, J. Chem. Phys. 118, 8207 (2003).
  46. [51]A. V. Krukau, O. A. Vydrov, A. F. Izmaylov, and G. E. Scuseria, J. Chem. Phys. 125, 224106 (2006).
  47. [52]Reference solar spectral irradiance: Air mass 1.5 retrieved 19 june 2025, https://www.nrel.gov/grid/solar-resource/spectra-am1.5.
  48. [53]S. Kim, K. Chae, and Y.-W. Son, Nanoscale 12, 15638 (2020).
  49. [54]S.-H. Kang, M. Kang, S. W. Hwang, S. Yeom, M. Yoon, J. M. Ok, and S. Yoon, Nanomaterials 13, 3111 (2023).
  50. [55]L. J. Phillips, C. N. Savory, O. S. Hutter, P. J. Yates, H. Shiel, S. Mariotti, L. Bowen, M. Birkett, K. Durose, D. O. Scanlon, and J. D. Major, IEEE Journal of Photovoltaics 9, 544 (2019).
  51. [56]R. Car and M. Parrinello, Phys. Rev. Lett. 55, 2471 (1985).
  52. [57]S. Nosé, The Journal of Chemical Physics 81, 511 (1984).
  53. [58]W. G. Hoover, Phys. Rev. A 31, 1695 (1985).

Paper details

vlnc:W_r47zf82e
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents