betaFeedback

WorksPhysics and Astronomy

Record Responsivity-conductance Performance in Sub-bandgap-triggered Ga2O3 PCSS

Abstract

We present an investigation into the role of anode grid pitch and excitation spectrum on the performance of high-power optoelectronic switches utilizing Fe-doped ββ-Ga2_2O33. By systematically varying the anode grid pitch (20−80 μm20-80\ μ\text{m}) and the excitation spectrum (235−500 nm235-500\ \text{nm}), we identify a crucial sub-bandgap regime, centered at 272 nm272\ \text{nm}, that effectively activates deep-level defect states. This activation is shown to enable highly efficient bulk carrier transport, a significant contrast to conventional above-bandgap excitation which is hampered by shallow surface absorption. The sub-bandgap illumination promotes strong photocurrent generation and substantially improved carrier collection efficiency. Under optimized conditions, specifically utilizing a 40 μm40\ μ\text{m} anode pitch, the fabricated device achieves a high peak photocurrent of 4.14 A4.14\ \text{A} and a record-low on-resistance of 10.4 Ω10.4\ Ω. To quantify this simultaneous high-performance achievement, we introduce a responsivity-conductance figure of merit (FoMRC\text{FoM}{_{RC}}), which attains a record value of 4.7×10−6 S/W4.7 \times 10^{-6}\ \text{S/W}. These findings robustly demonstrate the superior suitability of Fe-doped ββ-Ga2_2O3_3 for next-generation high-power optoelectronic switching applications, enabling reliable ampere-level photocurrents coupled with minimized on-resistance through strategic device geometry optimization and sub-bandgap excitation.

Introduction

Photoconductive semiconductor switches (PCSSs) yield ultrafast switching dynamics by optically modulating the conductivity of a bulk semiconductor substrate rapidly [1][2]. Furthermore, the optical excitation of a PCSS prevents backpropagation from a high-voltage power stage to a low-voltage microelectronics control unit, which is a common issue in typical switching power-electronics systems due to high voltage and current slew rates [3]. As such, PCSSs have wide applications, including, but not limited to, pulsed power, fly-by-light, solid-state circuit breakers, kinetic weapons, electromagnetic launch systems, high-power radio-frequency power amplifiers, etc. The confluence of ultrawide-bandgap (UWBG) semiconductors [4], which have higher critical electric-field strengths that yield high-voltage operation and lower device dimensions (and capacitances), and PCSS is expected to provide significant impetus to the growth and utility of these next-generation ultrafast optically-triggered power semiconductor technologies.

Among the UWBG semiconductors, gallium oxide (Ga2_2O3_3) [5] is considered one of the most promising for near-term commercialization, primarily due to its potential for large-area substrates, low cost, low threading dislocation density (TDD), and capability for large-scale production. High-quality Ga2_2O3_3 epilayers are now possible using MOCVD, HVPE, and MBE, with excellent wide-n-type doping control and low background compensation. As such, high-voltage electrical power semiconductor devices like power MOSFETs and diodes are already being pursued, and preliminary demonstrations have been conducted [6], [7]. Recently, experimental research on Ga2_2O3_3 PCSS, utilizing a longer wavelength optical beam and low current and voltage, has been initiated [8], which illustrates the preliminary potential of this UWBG material and highlights the need for further exploration in this promising area.

This work investigates the impact of varying the anode electrode grid pitch separation (which also serves as the optical window) and the wavelength of optical excitation on maximizing the responsivity-conductance trade-off in a Fe-doped β\beta-Ga2_2O3_3 PCSS. The experimental results demonstrate that Fe-doped β\beta-Ga2_2O3_3 PCSS supports ampere-level current conduction and record-low on-resistance under medium operating voltages, while extending the photoresponse into longer wavelength regimes. These results highlight the advantages of Fe-doped β\beta-Ga2_2O3_3 over previously reported UWBG PCSS devices, demonstrating the former's potential as a cost-effective optical device for next-generation high-power optoelectronic switching applications.

Device Structure and Fabrication

The β\beta-Ga2_2O3_3 PCSS were fabricated using double-side–polished 450 μ\mum thick, Fe-doped semi-insulating β\beta-Ga2_2O3_3 (010) substrates obtained from Kyma Technologies with an Fe doping concentration of approximately 1×10181 \times10^{18} cm−3^{-3}. Prior to fabrication, the substrate was sequentially cleaned in acetone, isopropyl alcohol (IPA), and deionized (DI) water, followed by drying with high-purity nitrogen to remove organic residues and surface contaminants. Figure 1 presents both the schematic cross-section and top-view micrographs of the fabricated devices. The device structure (Figure 1) comprises a continuous ground electrode on the back surface and a grid-type top electrode on the top surface, allowing direct optical access to the active region. Both electrodes were formed by electron-beam evaporation of a Ti/Au (50 nm/100 nm) bilayer. The top electrode was patterned by image-reversal lithography (AZ 5214E) and lift-off to define a grid geometry consisting of alternating metal fingers and transparent apertures. The devices were subjected to rapid thermal annealing at 480 °C for one minute in a nitrogen ambience to achieve ohmic contact [9].

Figure 1. (a) Schematic cross-section and (b) top view of the fabricated Fe-doped β\beta-Ga2_2O3_3 PCSS.

The grid-like anode electrode of the PCSS produces a predominantly vertical electric field across the illuminated region, while fringing fields near the finger edges provide lateral components that assist in collecting carriers generated close to the surface. To explore the role of electrode geometry, the electrode pitch gg Figure 1(a) was systematically varied between 20 and 80 µm. A narrow pitch enhances carrier collection through strong fringing-field overlap and shorter lateral drift paths, whereas a wider pitch increases the optical fill factor but introduces extended low-field regions between fingers that limit transport efficiency. This response exhibits a strong wavelength dependence: short-wavelength UV photons are absorbed within nanometer-scale depths, where transport is dominated by lateral drift and surface recombination. In contrast, sub-bandgap illumination penetrates deeper into the bulk, generating carriers that couple to the vertical electric field. This volumetric excitation makes the photocurrent response highly sensitive to electrode spacing, requiring an optimized pitch to balance optical access with field intensity. Importantly, the pitch variation does not alter the dominant vertical conduction path through the 450 µm substrate but instead modifies the lateral access to vertical field lines, thereby shaping carrier collection dynamics, peak current, and the observed switching speed. Systematic pitch variation, therefore, provides a controlled means of benchmarking device performance limits and deriving design guidelines for robust high-field switching operation.

Experimental Test Setup Configuration

A Keithley 2657A source meter, interfaced to a probe station using a Keithley 8020 high-power interface channel, is used to measure the dark current and off-state resistance (ROFFR_{\mathrm{OFF}}). For transient response, the PCSS devices were packaged in an optical open-cavity package using both thermally and electrically conductive epoxy. Connections with the package pins were enabled using wire bonding, as shown in Figure 2(a). Figure 2(b) shows the experimental setup used for the optical triggering of the PCSS devices. A 100 nF capacitor is charged to the desired DC bias (VbiasV_{\mathrm{bias}}) through a 1 kΩ current-limiting resistor. All PCSS devices are triggered using an OPOLETTE UX06230U tunable laser with a beam diameter of 3 mm and a full width at half maximum (FWHM) of 7 ns. The intensity of the laser beam varies with respect to wavelength. Once the PCSS device is optically excited, the resulting electrical pulse is measured across a 50-Ω terminating load resistor (RloadR_{\mathrm{load}}) using a Tektronix TPP1000 voltage probe and a Tektronix MSO46 oscilloscope, both of which have a bandwidth of 1 GHz. The laser pulse profile is simultaneously monitored using a high-speed silicon photodetector (DET10A2, Thorlabs).

Figure 2. (a) The packaged Fe-doped β\beta-Ga2_2O3_3 PCSS. (b) A test set-up for transient characterization of the PCSS.

PCSS Experimental Results and Analysis

The photo responses of four Fe-doped β\beta-Ga2_2O3_3 PCSS devices with top electrode pitches of 20, 40, 60, and 80 µm were systematically characterized under a DC bias (VbiasV_{\mathrm{bias}}) of 250 V over the wavelength range of 235–500 nm. These measurements for the PCSS capture both above-bandgap and sub-bandgap response regimes.

The normalized responsivity and the responsivity–conductance figure of merit (FoMRCFoM_{RC}) of Fe-doped β-Ga₂O₃ PCSS devices with different electrode gaps as a function of incident wavelength are shown in Figure 3a and Figure 3b, respectively. To isolate the intrinsic switching performance from the circuit-limited current saturation, a quantitative metric for switching efficiency, FoMRCFoM_{RC} is introduced. This metric is defined as the increase in on-state conductance per unit optical power; that is, FoMRC=GON/POPTFoM_{RC}=G_{ON}/P_{OPT}, where GON≈1/RONG_{ON}\approx1/R_{ON} (RONR_{ON} is the on-state resistance of the PCSS) represents the net photoconductance and POPTP_{OPT} is the peak incident optical power. All devices displayed a pronounced responsivity peak in the range of 270–275 nm, occurring at wavelengths approximately 12–17 nm longer than the intrinsic absorption edge of β-Ga₂O₃ (~258 nm). This offset suggests that contributions from sub-bandgap processes may play a significant role in this regime, in addition to, or instead of, direct band-to-band transitions. At the intrinsic absorption edge, most incident photons are absorbed within a few nanometers of the PCSS surface due to the large absorption coefficient [10], which limits the effective generation of carriers. The enhanced response near 272 nm can be considered in relation to Urbach tail absorption as well as the possible photoionization of deep-level defect complexes within the semi-insulating substrate [11, 12]. Earlier deep-level optical and transient spectroscopy studies have reported several defect states in β-Ga₂O₃, including ECE_C-0.63 eV, ECE_C-0.81 eV, ECE_C-1.29 eV, ECE_C-2.0 eV, and ECE_C-4.48 eV [13, 14, 15, 16, 17, 18]. The ECE_C-0.81 eV state is often associated with Fe dopant activation [19, 20]. In addition, Angeloni et al. [21] identified Fe-related states at ECE_C-3.05 ± 0.05 eV and ECE_C-3.85 ± 0.05 eV using picosecond tunable UV spectroscopy. Sub-bandgap excitation around 272 nm may therefore facilitate carrier photoionization from these Fe-related defect states, which could explain the enhanced responsivity observed in this wavelength range.

Normalized responsivity

(a)

Responsivity–conductance figure of merit

(b)

Figure 3. Normalized responsivity and b) responsivity–conductance figure of merit (FoMRCFoM_{RC}) of the Fe-doped β-Ga₂O₃ PCSS with variation in wavelength.

Figure 4(a) presents the peak photocurrent (IPeakI_{Peak}), while Figure 4(b) shows the corresponding minimum on-resistance (RONR_{ON}) for both above- and sub-bandgap excitations. The photocurrent responses exhibit distinct regimes determined by the carrier generation profiles, arising from the interplay between wavelength-dependent optical penetration depth and the electric-field distribution. For deep sub-bandgap excitation (450 and 500 nm), photocarriers are generated predominantly through volumetric excitation of Fe- and Ir-related deep levels within the bulk. These carriers couple efficiently to the vertical drift field, yielding intermediate photocurrent values (approximately 1–1.7 A at 450 nm and < 1 A at 500 nm). Both wavelengths exhibit a clear maximum at a 40 μm pitch. This trend reflects a trade-off where the active collection volume expands with pitch but is eventually overtaken by the reduction in average electric-field intensity at larger gaps. Under above-bandgap excitation (245–255 nm), carrier generation is confined to a shallow near-surface region. Carrier transport is dominated by lateral diffusion and surface-driven drift, where strong surface recombination suppresses the photocurrent response (< 1 A). The slight increase in photocurrent observed with increasing pitch is ascribed to the geometric expansion of the photo-active surface area, although the dominance of diffusion-limited transport prevents significant scaling.

Figure 4. (a) Peak photocurrent and (b) minimum on-resistance for different PCSSs when optically excited with sub- and above-bandgap wavelengths.

Near-band-edge excitation (272 and 300 nm) produces strong photocurrent response owing to an optimal penetration depth that simultaneously activates deep levels and maintains strong near-surface generation. Specifically, under 272 nm excitation at a 40 μm pitch, the photocurrent reaches a saturation plateau of ~4.14 A. This value corresponds to the circuit-limited peak current (Ipeak=Vbias/(Rload+RON)I_{peak}=V_{bias}/(R_{load}+R_{ON})) defined by the 50-Ω load (RloadR_{load}) and VbiasV_{bias} of 250 V, indicating that the intrinsic FoMRCFoM_{RC} in this regime is sufficiently high to drive the device into a fully conductive state (RONR_{ON} ~10.4 Ω), limited only by the external circuit. At 300 nm, the pitch dependence resembles that of the deep sub-bandgap regime, exhibiting a clear peak at 40 μm followed by a sharp drop at 80 μm. For the 272 nm case, the photocurrent remains nearly constant over the 20–60 µm range due to this saturation effect. However, at 80 µm, both near-band-edge wavelengths display a pronounced decline. This reduction is attributed to reduced overlap of lateral fringing fields at the widest anode spacing, which weakens carrier funneling into the high-field vertical region and consequently limits the overall photo-collection efficiency.

The transient photoresponses of Fe-doped β\beta-Ga2_2O3_3 PCSS devices were analyzed by extracting the switch-on and switch-off times as functions of excitation wavelength. The switch-on time (τr\tau_r) is defined as the interval required for the photocurrent to reach its peak, while the switch-off time (τd\tau_d) corresponds to the decay from peak to zero current. As shown in Figure 5(a), τr\tau_r exhibits a distinct wavelength dependence, serving as a sensitive spectroscopic indicator of deep-level defect dynamics. Two regimes can be identified: an intrinsic regime (λ<270\lambda< 270 nm, hν≳4.6h\nu\gtrsim4.6 eV) characterized by direct band-to-band excitation (~1–1.5 ns), and an extrinsic regime (λ>270\lambda> 270 nm) dominated by slower (2.5–5 ns) trap-assisted transport. Specific spectral features in τr\tau_r correspond to discrete defect levels: the delay peak near 280–300 nm arises from carrier excitation into Urbach tail states, while the feature around 350 nm is attributed to the ~3.5 eV optical transition associated with oxygen vacancies (VoV_o). The broader maximum near 450 nm likely reflects overlapping contributions from Fe2+^{2+}/Fe3+^{3+} levels (~3.05 eV), gallium vacancies (VGa≈3.0V_{Ga} \approx3.0 eV), and multi-step charge-transfer transitions involving Ir-related centers (EIr>2.0E_{Ir} > 2.0 eV).

Figure 5. (a) Switch-on and (b) switch-off times of the Fe-doped Ga2_2O3_3 PCSS with variation in excitation wavelength.

The decay dynamics, shown in Figure 5(b), exhibit a complementary trend. Under high-energy excitation (λ<260\lambda< 260 nm), rapid current quenching occurs due to efficient electron–hole recombination following band-to-band absorption. For λ>300\lambda> 300 nm, excitation predominantly activates shallow defect levels, resulting in a weak and short-lived photocurrent. Notably, illumination within the 270–280 nm range photoionized a specific defect complex that forms long-lived hole traps, resulting in a persistent photocurrent and a markedly prolonged switch-off time. This persistent photocurrent is attributed to the photoionization of a defect complex likely associated with Fe-dopants or oxygen vacancies that functions as a long-lived hole trap [22, 23].

In summary, excitation at 245 nm yields ultrafast rise times (< 2 ns) but relatively low responsivity (~5.5 × 10−6^{-6} A-cm/W-kV). In contrast, excitation at 272 nm produces a relatively slower rise time (~4.5 ns) but yields a significantly higher responsivity of 3.89×10−53.89 \times10^{-5} A-cm/W-kV, together with a low RONR_{\mathrm{ON}} of 10.4 Ω\Omega, indicating an efficient switching. The comparative 3D plots in Figure 6 highlight the improved performance of the developed Fe-doped β\beta-Ga2_2O3_3 PCSS relative to the previously reported UWBG photoconductive switches. As shown in Figure 6(a), the device exhibits a markedly lower voltage-to-peak-current ratio, indicating efficient high-current conduction under moderate bias and sub-bandgap optical excitation. This enhanced current-driving capability—delivering ampere-level photocurrents with a RONR_{\mathrm{ON}} of ∼10\sim10 Ω\Omega—contrasts sharply with previously reported Fe-doped β\beta-Ga2_2O3_3 and diamond-based PCSS devices that required higher optical power or exhibited substantially higher RONR_{\mathrm{ON}}.

Figure 6. Performance comparison of the Fe-doped β\beta-Ga2_2O3_3 PCSS with previously reported UWBG photoconductive switches: (a) Voltage-to-peak-current ratio (where voltage refers to the power bias) and (b) responsivity–conductance figure of merit (FoMRCFoM_{RC}) as a function of wavelength and peak power of the optical beam.

Complementarily, Figure 6(b) presents a comparison of the responsivity–conductance figure of merit (FoMRCFoM_{RC}) of previously reported Ga2_2O3_3- and diamond-based PCSS devices. A high FoMRCFoM_{RC} of 4.7×10−64.7 \times10^{-6} S/W is demonstrated at 272 nm. Notably, this high FoMRCFoM_{RC} is achieved alongside a record-low on-resistance of 10.4 Ω\Omega, representing a new benchmark in the responsivity-conductance performance space. The improvement is attributed to an optimized electrode geometry, which provides a uniform electric field distribution and enhances carrier collection efficiency. Collectively, these results establish the present Fe-doped β\beta-Ga2_2O3_3 PCSS as a new performance benchmark among UWBG photoconductive switches, combining high peak photocurrent, low on-resistance, and strong optical-to-electrical conversion efficiency within a compact and scalable device architecture. A logarithmic vertical scale is used to capture the wide dynamic range of responsivity and current, allowing both low- and high-level performance regimes to be clearly visualized within the same plots.

Conclusions

This work demonstrates the record responsivity–conductance figure of merit (FoMRCFoM_{RC}) under sub-bandgap excitation in Fe-doped β\beta-Ga2_2O3_3 PCSS. This performance enhancement is enabled through the concurrent optimization of the anode-grid pitch, serving as both the optical access window and the electric-field shaping element, and the excitation wavelength. The results show that excitation at 272 nm with a 40-μ\mum contact pitch maximizes volumetric carrier generation and collection, yielding a peak photocurrent of 4.14 A, a record-low on-resistance of 10.4 Ω\Omega, and a corresponding FoMRCFoM_{RC} of 4.71×10−64.71 \times10^{-6} S/W, thereby establishing a new benchmark for UWBG photoconductive switching technologies. For excitation at wavelengths longer and shorter than this optimum wavelength, device performance progressively diminishes due to increased optical transmission (weaker absorption) and surface-confined photocarrier generation (experiencing weak vertical field), respectively, both of which limit collection efficiency. Collectively, these results position Fe-doped β\beta-Ga2_2O3_3 as a highly promising, cost-effective platform for next-generation high-power photoconductive switching, offering superior conductance and efficiency compared to recently reported UWBG-based PCSS counterparts.

Acknowledgement

The information, data, or work presented herein was funded in part by the Advanced Research Project Agency-Energy (ARPA-E), U.S. Department of Energy, under Award Number DE-AR0001879. Authors also acknowledge the support of the Nanotechnology Core Facility (NCF) at the University of Illinois Chicago.

Author Declarations

Conflict of Interest: The authors declare no conflicts of interest.

Data Availability

The data that supports the findings of this study are available from the corresponding author upon reasonable request.

References

  1. [1]D. H. Auston and A. M. Glass, “Optical generation of intense picosecond electrical pulses,” Appl. Phys. Lett., vol. 20, no. 10, pp. 398–399, May 1972.
  2. [2]A. Rosen and F. J. Zutavern, Editors, High-power optically activated solid-state switches, Artech House Publishers, 1994.
  3. [3]S. K. Mazumder, "An overview of photonic power electronic devices," in IEEE Transactions on Power Electronics, vol. 31, no. 9, pp. 6562-6574, Sept. 2016, doi: 10.1109/TPEL.2015.2500903DOI
  4. [4]J. Y. Tsao et al., “Ultrawide-bandgap semiconductors: Research opportunities and challenges,” Advanced Electronic Materials, vol. 4, 2018, DOI: 10.1002/aelm.201600501DOI
  5. [5]S. J. Pearton et al., “A review of Ga₂O₃ materials, processing, and devices,” Appl. Phys. Rev., vol. 5, Jan. 2018, Art. no. 011301.DOI
  6. [6]S. K. Mazumder et al., "High-Voltage-Design and Ultrafast-Switching Issues of an UWBG Vertical Ga2 O3 MOSFET," 2025 IEEE Energy Conversion Congress & Exposition Asia (ECCE-Asia), Bengaluru, India, 2025, pp. 1-6, doi: 10.1109/ECCE-Asia63110.2025.11111809.DOI
  7. [7]Islam et al. (2022). “500 °C operation of β-Ga₂O₃ field-effect transistors.” Applied Physics Letters, 121, 243501.DOI
  8. [8]K. M. Dowling et al., "Evaluation of Fe-βGa₂O₃ for Photoconductive Semiconductor Switching," in IEEE Transactions on Electron Devices, vol. 71, no. 3, pp. 1535-1540, March 2024, doi: 10.1109/TED.2024.3352528.
  9. [9]A. Y. Polyakov, N. B. Smirnov, I. V. Shchemerov, S. J. Pearton, Fan Ren, A. V. Chernykh, A. I. Kochkova; Electrical properties of bulk semi-insulating β-Ga2O3 (Fe). Appl. Phys. Lett. 1 October 2018; 113 (14): 142102.DOI
  10. [10]Hassanien, A.M., Atta, A.A., El-Nahass, and M. M. El-Nahass et al. Effect of annealing temperature on structural and optical properties of gallium oxide thin films deposited by RF-sputtering. Opt Quant Electron 52, 194 (2020). https://doi.org/10.1007/s11082-020-02306-8
  11. [11]Ibrahim Hanif, Ge Yang, Chuanzhen Elaine Zhou, Cheng Sun, Kenan Gundogdu, Dovlegen O. Danilov, Felix N. Castellano, Dali Sun, and Eric Vetter, Low temperature cathodoluminescence study of Fe-doped β-Ga₂O₃, Materials Letters, Volume 257,2019,126744, ISSN 0167-577X. https://doi.org/10.1016/j.matlet.2019.126744.
  12. [12]Look, D. C., Leedy, D. Classical and quantum conductivity in β-Ga₂O₃. Sci Rep 9, 1290 (2019). https://doi.org/10.1038/s41598-018-38419-0
  13. [13]Z. Zhang, E. Farzana, A. R. Arehart, and S. A. Ringel; Deep level defects throughout the bandgap of (010) β-Ga₂O₃ detected by optically and thermally stimulated defect spectroscopy. Appl. Phys. Lett. 1 February 2016; 108 (5): 052105. (Also available at https://doi.org/10.1063/1.4941429)
  14. [14]Esmat Farzana, Max F. Chaiken, Thomas E. Blue, Aaron R. Arehart, and Steven A. Ringel; Impact of deep level defects induced by high energy neutron radiation in β-Ga₂O₃. APL Mater. 1 February 2019; 7 (2): 022502. (Also available at https://doi.org/10.1063/1.5054606)
  15. [15]Esmat Farzana, Elaheh Ahmadi, James S. Speck, Aaron R. Arehart, and Steven A. Ringel; Deep level defects in Fe-doped (010) β-Ga₂O₃ layers grown by plasma-assisted molecular beam epitaxy. J. Appl. Phys. 28 April 2018; 123 (16): 161410. (Also available at https://doi.org/10.1063/1.5010608)
  16. [16]Hemant Ghad, Joe F. McGlone, Christine M. Jackson, Esmat Farzana, Zixuan Feng, A. F. M. Anhar Uddin Bhuiyan, Hongping Zhao, Aaron R. Arehart, and Steven A. Ringel; Full bandgap defect state characterization of β-Ga₂O₃ grown by metal organic chemical vapor deposition. APL Mater. 1 February 2020; 8 (2): 021111.DOI
  17. [17]Jiaye Zhang, Jueli Shi, Dong-Chen Qi, Lang Chen, Kelvin H. L. Zhang; Recent progress on the electronic structure, defect, and doping properties of Ga₂O₃. APL Mater. 1 February 2020; 8 (2): 020906. (Also available at https://doi.org/10.1063/1.5142999)
  18. [18]A. Y. Polyakov et al., “Electrical Properties, Deep Levels and Luminescence Related to Fe in Bulk Semi-Insulating β-Ga₂O₃ Doped with Fe,” 2019 ECS J. Solid State Sci. Technol. 8 Q3091DOI 10.1149/2.0171907jssDOI
  19. [19]S. B. Bhandari, M. E. Zvanut, and J. B. Varley; Optical absorption of Fe in doped Ga₂O₃. J. Appl. Phys. 28 October 2019; 126 (16): 165703. (Also available at https://doi.org/10.1063/1.5124825)
  20. [20]Christian Zimmermann, Ymir Kallmann Frodason, Abraham Willem Barnard, Joel Basile Varley, Klaus Irmscher, Zbigniew Galazka, Antti Karjalainen, and Walter Ernst Meyer, Francois Danie Auret, and Lasse Vines; Ti- and Fe-related charge transition levels in β-Ga₂O₃. Appl. Phys. Lett. 18 February 2020; 116 (7): 072101. https://doi.org/10.1063/1.5139402
  21. [21]L. A. Angeloni, I.-J. Shan, J. H. Leach, and W. A. Schroeder; Iron dopant energy levels in β-Ga₂O₃. Appl. Phys. Lett. 17 June 2024; 124 (25): 252104. (Also available at https://doi.org/10.1063/5.0213263)
  22. [22]Andrew M. Armstrong, Mary H. Crawford, Asanka Jayawardena, Ayayi Ahyi, and Sarit Dhar; Role of self-trapped holes in the photoconductive switching of β-gallium oxide Schottky diodes. J. Appl. Phys. 14 March 2016; 119 (10): 103102. https://doi.org/10.1063/1.4943261
  23. [23]Suman Bhandari, Claudia Nardone, and M. E. Zvanut; Optical transitions of gallium vacancies in neutron irradiated β-Ga₂O₃. J. Appl. Phys. 14 July 2022; 132 (2): 025701. https://doi.org/10.1063/5.0100352

Paper details

vlnc:W_r6dfxut7
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents