betaFeedback

WorksPhysics and Astronomy

Numerical study on femtosecond electro-optical spatial decoding of transition radiation from laser wakefield accelerated electron bunches

Abstract

This numerical study is focused on electro-optic (EO) spatial decoding of transition radiation (TR) produced by a relativistic electron bunch passing through a metal foil. The calculations included the imaging of polychromatic transition radiation from an electron bunch and the process of EO spatial decoding. From an experimental perspective, a careful examination of the calculation approach of the data analysis is essential. Therefore, to thoroughly understand the process of signal generation and examine the possibility of adopting a less time-consuming treatment, comparative studies were conducted on detailed and simplified models of both transition radiation imaging and EO signal generation. All calculations are defined in SI units for the convenience of experimental measurements. For TR imaging, the results suggest that the simplified analytical model is sufficient to perform polychromatic calculations with considerable accuracy. For EO spatial decoding, we discussed the process of EO signal generation using 1D and 2D models. We found that the 1D model was sufficient for rapid data analysis. Furthermore, the temporal energy chirp was demonstrated to have a minimal impact on the shape of the EO signal. Because both the transverse and longitudinal profiles can be calculated with arbitrary distributions, this numerical study can facilitate measurements of 3D electron charge density profiles in both laser wakefield acceleration and conventional accelerator research.

Introduction

Laser wakefield acceleration[1, 2, 3, 4], with an inherent ultrashort timescale and ultrahigh acceleration gradient, has attracted great interest worldwide. With the incidence of a high-power femtosecond (fs) laser beam on an underdense plasma, electron plasma waves with a wavelength of a few tens of micrometers (μ\mum) and an electric field strength of >100> 100 GeV/m can be stimulated. Trapped electrons achieve energies of over GeV [5, 6, 7, 8, 9, 10] within a centimeter. In 2021, free-electron lasing at 27 nm driven by a laser wakefield accelerator (LWFA) was demonstrated via the generation of high-quality electron bunches [11, 12].

The three-dimensional (3D) charge density distribution of a relativistic electron bunch is an important parameter for secondary radiation sources of an LWFA, such as betatron X-rays [13, 14], inverse Compton scattering [15], and X-ray free electron lasers (XFELs) [16]. The duration of the electron bunch partially determines the temporal resolution of a pump-probe experiment. The gain length of lasing processes in an undulator [17] is affected by the 3D charge density.

Electro-optic (EO) sampling [18] [19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30] was applied to accelerator studies 20 years ago owing to its single-shot and non-destructive capabilities. Pioneering numerical studies focused on this convenient method can be found in [29, 30]. When the electric field carrying the temporal information of the electron bunch propagates through an EO crystal, the effective principal axis of the crystal rotates because of the Pockels effect. With the incidence of a probe laser beam on a crystal, time information of the electron bunch can be reconstructed by analyzing the phase retardation. The longitudinal distribution of electrons is encoded transversely into the probe laser beam by setting a relative angle between the probe laser and the signal field. This is referred to as the “EO spatial decoding technique” [26].

EO sampling of transition radiation (TR) of an electron bunch has been conducted to measure the relative electron longitudinal profile [31, 32] or the field strength of a terahertz pulse [33]. However, simultaneous measurement of the absolute current and transverse profiles has not been attempted. By the incidence of the TR pulse onto the EO crystal and the performing the spatial decoding, the TR field produced by the electron bunch is measured both temporally and spatially. We named the detection method as the “TR-EO” method in this study.

In this article, we performed numerical calculations of EO spatial decoding of TR produced by a relativistic electron bunch passing through a metal foil. The calculations involved the imaging of polychromatic TR from electron bunches with arbitrary shapes and energies and the EO spatial decoding process, including TR absorption by the crystal, smearing, and phase mismatch, which are affected by the relative angle and speed difference between the TR and the probe laser. All calculations in this study are defined in SI units for ease of implementation. Detailed and simplified models were discussed for the calculations of both the TR imaging and EO signal generation. Through the comparison of results, the feasibility of the simplified models for a quicker analysis was demonstrated. In addition, we calculated the impact of temporal energy chirps of electrons on the EO signals and concluded that the current profiles dominated the shapes of the EO signals.

This paper is organized as follows: the experimental setup of this numerical study is described in § 2. The calculation of the polychromatic TR field via a detailed Huygens–Fresnel diffraction calculation and a simplified analytic model based on Fraunhofer approximation is described in § 3. The EO spatial decoding process is described in § 6 using a simplified model and a detailed 2D interpolation method. The impact of the temporal energy chirp of electrons on the EO signal is discussed in § 6. Thereafter, noise in transition radiation generated by the optical system is calculated in § 9. Finally, the discussion and conclusions of this study are presented in Sec. VI.

Experimental Concept of This Numerical Study

Numerical calculations were conducted to quantitatively explain the aspects that can be achieved using the experimental concept illustrated in Figure 1. In the LWFA, a drive laser beam was incident on a gas target to generate an electron beam. Therefore, electron bunches propagated with the outgoing drive laser beam. However, an intense drive laser can result in damage and noise during particle parameter measurements in the LWFA. Therefore, a metal foil (e.g., aluminum, or stainless steel) was placed in the electron beam path to eliminate noise generated by the drive laser beam and produce TR. Subsequently, the TR emission was imaged using two off-axis parabolic (OAP) mirrors and was incident onto an EO crystal. Typically, crystals with a zinc-blende structure are used. An ultrashort probe laser beam with a small incident angle θp\theta_p to the EO crystal was used to perform spatial decoding. The [−1,1,0][-1,1,0] axis of the crystal was parallel to the polarization direction of the probe laser and orthogonal to the plane formed by the probe laser beam and the TR propagation direction. Further, half-wave and quarter-wave plates were inserted to perform the near-cross-polarization [29] detection. The TR passing through the crystal was then imaged again to measure the optical transition radiation (OTR). Because the TR field had a wavelength range from visible to infrared, it is recommended that the EO crystal be placed inside a vacuum chamber to avoid unwanted absorption from the vacuum window and air. For the same reason, the gold-coated OAP was used instead of a lens to deliver the TR pulse beam.

Conceptual scenario of the TR-EO spatial decoding set-up in LWFA

Figure 1. Conceptual scenario of the TR-EO spatial decoding set-up in LWFA. e−e^{-}: electron bunch; OAP: Off-axis-parabolic gold mirror; S: polarizer before EO crystal; P: polarizer after EO crystal; λ/2\lambda/2: half waveplate; λ/4\lambda/4: quarter waveplate; and BP: bandpass filter. The inset shows the coordinates in the imaging plate. The [−1,1,0][-1,1,0] axis of the crystal is along the YDY_D direction. The polarization of the incident probe laser is also parallel to the YDY_D direction.

Three-Dimensional TR Electric Field in the Coordinates (XD,YD,T)(X_D,Y_D,T)

In this section, we present a 3D calculation of the TR field imaged on the EO crystal. The calculation geometry is shown in Figure 2. An electron bunch passed through a radiator (source plane), and TR was produced. The produced TR was collected by the first OAP (OAP1) with a focal length of F1F_1. The source point was placed at the focus of OAP1. Consequently, the collimated TR light was focused by OAP2 on the EO crystal. Here, (Xs,Ys)(X_s,Y_s) and (XD,YD)(X_D,Y_D) denote the mesh grids in the source and detector planes (EO crystals), respectively, and (XI1,YI1)(X_{I1},Y_{I1}) and (XI2,YI2)(X_{I2},Y_{I2}) are the mesh grids in the planes of OAP1 and OAP2, respectively, with the OAPs considered as thin lenses. The mesh grids were arranged symmetrically with the centers set at (0,0)(0, 0). The distance between OAP1 and OAP2 was denoted as LL. Further, rb=(Xb,Yb,Zb)\mathbf{r}_b=(X_b,Y_b,Z_b) denotes the relative position of a single electron inside the electron bunch. The wave number of the TR was k=kx2+ky2+kz2k=\sqrt{k_x^2+k_y^2+k_z^2} and it had a relative angle of θ\theta relative to the zz-axis. The direction of the [−1,1,0][-1,1,0] axis of the crystal was along the “YY” axes in Figure 2. For EO spatial decoding, the polarization of the probe laser beam was set along the [−1,1,0][-1,1,0] axis of the EO crystal to achieve maximum phase retardation.

Calculation geometry of the imaging of TR of an electron bunch

Figure 2. Calculation geometry of the imaging of TR of an electron bunch. OAP1 and OAP2 have effective focal lengths of F1F_1 and F2F_2, respectively. The distance between the OAPs is LL.

In this study, the third dimension “TT” or “ω\omega” was assumed to be decoupled from the transverse beam profile. First, we calculated the 2D spatial distribution of the TR field Ey(XD,YD,ω)E_y(X_D,Y_D,\omega) for a single-frequency component. Subsequently, the 2D image was multiplied by the longitudinal form factor Fz(ω)F_z(\omega). Finally, we performed a

Fourier transform of Ey(XD,YD,ω)E_y(X_D,Y_D,\omega) in the ω\omega dimension to obtain Ey(XD,YD,T)E_y(X_D,Y_D,T) distribution.

By treating the metal foil as an ideal conductor, the TR of a single electron can be calculated as the total reflection of the self-field (superposition of pseudo-photons). Here, without loss of generality, when passing through the foil, a single electron at position (0,0)(0,0) of the source plane is considered. The self-field expression (further details presented in Appendix A) of an electron in the frequency and wavenumber domains is expressed as,

Es(Xs,Ys)=ie(2π)2ε0v∬dkxdkyexp⁡[i(kxXs+kyYs)](kx,ky)kx2+ky2+α2(1)E^s(X_s,Y_s)=i\frac{e}{(2\pi)^2\varepsilon_0v}\iint\mathrm{d}k_x\mathrm{d}k_y\exp\left[i(k_xX_s+k_yY_s)\right]\frac{(k_x,k_y)}{k_x^2+k_y^2+\alpha^2} \tag*{(1)}
Es(Xs,Ys)=−eα2πε0v(Xs,Ys)Xs2+Ys2K1(αXs2+Ys2)(2)E^s(X_s,Y_s)=-\frac{e\alpha}{2\pi\varepsilon_0v}\frac{(X_s,Y_s)}{\sqrt{X_s^2+Y_s^2}}K_1\left(\alpha\sqrt{X_s^2+Y_s^2}\right) \tag*{(2)}

where α=ω/γv\alpha=\omega/\gamma v, where vv is the electron velocity, K1K_1 is a Bessel function of the second type, and ε0\varepsilon_0 denotes the electric constant. (1) and (2) are equivalent and used as the source field of the TR from an electron.

2D spatial imaging of the TR field

Calculations related to OTR imaging have been investigated in accelerator research to measure the transverse size of electron bunches. Both incoherent and coherent OTR imaging [34, 35, 36, 37, 38] have been focused upon. In these studies, a far-field model based on Fraunhofer assumption was widely used because the TR was specially treated in the optical range. However, because the EO sampling of the TR covers the wavelength range of zero to a few hundred THz, the validity of the Fraunhofer model should be discussed.

Detailed numerical diffraction calculation based on the Huygens–Fresnel principle

We calculated the 2D TR field Ey(XD,YD)E_y(X_D,Y_D) based on the Huygens–Fresnel principle [39] as follows:

U(x2,y2)=ziλ∬Σ1U(x1,y1)exp⁡(ikr12)r122dx1dy1(3)U(x_2,y_2)=\frac{z}{i\lambda}\iint_{\Sigma_1}U(x_1,y_1)\frac{\exp(ikr_{12})}{r_{12}^2}\mathrm{d}x_1\mathrm{d}y_1 \tag*{(3)}

where “1” and “2” are the indices of planes “1” and “2”, respectively, with a distance of zz, and UU is the scalar field distribution. Further, (x1,y1)(x_1,y_1) and (x2,y2)(x_2,y_2) are points on the two planes with the distance between them being r12=z2+(x2−x1)2+(y2−y1)2r_{12}=\sqrt{z^2+(x_2-x_1)^2+(y_2-y_1)^2}. The reasons for choosing the Huygens–Fresnel principle instead of Fresnel approximation are as follows: (i) the para-axial condition might not be fulfilled if the electrons have low energy because the TR has an angular peak at θpeak∼1/γ\theta_{\mathrm{peak}} \sim1/\gamma; and (ii) the acceptance angle of OAP1 is occasionally large in the experiment.

Equation (2) can be treated easily as a convolution. We defined the transfer function as:

H(x,y)=ziλexp⁡(ikz2+x2+y2)z2+x2+y2(4)H(x,y) = \frac{z}{i\lambda}\frac{\exp\left(ik\sqrt{z^{2}+x^{2}+y^{2}}\right)}{z^{2}+x^{2}+y^{2}} \tag*{(4)}

The Huygens–Fresnel principle expressed in Eq. (3) can be rewritten as follows:

U(x2,y2)=∬Σ1U(x1,y1)H(x2−x1,y2−y1) dx1dy1(5)U(x_{2},y_{2}) = \iint_{\Sigma_{1}} U(x_{1},y_{1})H(x_{2}-x_{1},y_{2}-y_{1})\,\mathrm{d}x_{1}\mathrm{d}y_{1} \tag*{(5)}

By setting both planes with the same mesh grid, the diffraction can be calculated using the following Fourier transformation:

U2=U1∗H=F−1[F(U1)×F(H)](6)U_{2} = U_{1} * H = \mathcal{F}^{-1}\left[\mathcal{F}(U_{1}) \times\mathcal{F}(H)\right] \tag*{(6)}

where F\mathcal{F} and F−1\mathcal{F}^{-1} denote the Fast Fourier Transformation (FFT) and Inverse FFT, respectively. Three transfer functions {H1,HL,H2}\{H_{1}, H_{L}, H_{2}\} existed in the system with different longitudinal distances as {F1,L,F2}\{F_{1}, L, F_{2}\}.

There were three optical apertures with sharp edges (step functions) in the imaging system: (i) a finite size of the metal foil DsD_{s}, (ii) a finite size of OAP1; and (iii) a finite size of OAP2. In this study, we set up two OAPs with the same radius RlR_{l} and focal length FF. These apertures can be described by the following matrices:

Ps(Xs,Ys)={∣Xs∣,∣Ys∣}<Ds/2P_{s}(X_{s},Y_{s}) = \{|X_{s}|,|Y_{s}|\} < D_{s}/2
Pl(Xl,Yl)=Xl2+Yl2<Rl(7)P_{l}(X_{l},Y_{l}) = \sqrt{X_{l}^{2}+Y_{l}^{2}} < R_{l} \tag*{(7)}

where Ps(Xs,Ys)P^{s}(X_{s},Y_{s}) is the square pupil (metal foils often have square shapes) at the source plane and Pl(Xl,Yl)P^{l}(X_{l},Y_{l}) is the round pupil created by the OAPs.

An OAP with an effective focal length FF can be considered an ideal lens without spherical aberrations (explanations are provided in Appendix B). The converging effect of a lens results in a relationship between the field at the left side of the lens EllE^{ll} and the right side of the lens ElrE^{lr} as follows:

Elr(Xl,Yl)=Ellexp⁡(−ikXl2+Yl22F)(8)E^{lr}(X_{l},Y_{l}) = E^{ll}\exp\left(-ik\frac{X_{l}^{2}+Y_{l}^{2}}{2F}\right) \tag*{(8)}

where FF is the focal length of the lens. The wavefront difference before and after the OAP is expressed as,

PTl=exp⁡(−ikXl2+Yl22F)(9)PT_{l} = \exp\left(-ik\frac{X_{l}^{2}+Y_{l}^{2}}{2F}\right) \tag*{(9)}

Considering the transverse distribution of g⊥(Xs,Ys)g_{\perp}(X_{s},Y_{s}), the Coulomb field of one slice in the electron bunch at the source plane is a convolution, which is expressed as follows:

Cous(Xs,Ys)=g⊥∗Es(10)Cou^{s}(X_{s},Y_{s}) = g_{\perp} * E^{s} \tag*{(10)}

Here, we used the expression of the field of a single electron EsE^{s}, as expressed in Eq. (1b). The transverse distribution was arbitrary. The TR field on the left side of the OAP1 was calculated as follows:

Ell(Xl1,Yl1)=(Ps×Cous)∗H1(11)E^{ll}(X_{l1},Y_{l1}) = (P_{s} \times Cou^{s}) * H_{1} \tag*{(11)}

The diffractive propagation of the TR from the left side of OAP1 to the left side of OAP2, including the phase shift and aperture of OAP1, was calculated as follows:

Ell2(Xl2,Yl2)=(Pl×PTl×Ell1)∗HL(12)E^{ll2}(X_{l2},Y_{l2}) = (P_{l} \times PT_{l} \times E^{ll1}) * H_{L} \tag*{(12)}

Similarly, TR field propagation from the left side of OAP2 to the EO crystal was calculated as follows:

ED(XD,YD)=(Pl×PTl×Ell2)∗H2(13)E^{D}(X_{D},Y_{D}) = (P_{l} \times PT_{l} \times E^{ll2}) * H_{2} \tag*{(13)}

Equations (9–12) show the quantitative calculation procedures for the diffractive propagation of the TR field. We set Rl=25.4 mmR_{l}=25.4\ \mathrm{mm} and F=190 mmF=190\ \mathrm{mm} for the current and subsequent calculations. The distance between both the OAPs was set to L=40 cmL=40\ \mathrm{cm}. The TR field profiles of Ell1E^{ll1}, Ell2E^{ll2}, and EDE^{D} were calculated to check the diffraction patterns, as shown in Figure 3. We first performed calculations using an electron energy of 250 MeV250\ \mathrm{MeV} with a TR wavelength of 100 μm100\ \mu\mathrm{m}. In this case, the effective electron radius [34, 36] was γλ∼5 cm\gamma\lambda\sim5\ \mathrm{cm}. A transverse beam of size (50,50) μm(50, 50)\ \mu\mathrm{m} was assumed. The results of metal foil sizes of Ds={1,10} cmD_{s}=\{1, 10\}\ \mathrm{cm} were compared, as shown in Figs. 3(a–f). Although the diffraction patterns at the positions of the OAPs were slightly different, the TR field distributions in the EO crystal were almost identical. This calculation facilitated an understanding of the diffraction of the TR field at intermediate positions inside the optical system. Furthermore, this indicates that, in most cases, the variation in the metal foil size should merely result in a difference in the field strength at the imaging point.

Calculation results based on the Huygens–Fresnel principle

Figure 3. Calculation results based on the Huygens–Fresnel principle. The ∣EY(X,Y,f)∣|E_Y(X,Y,f)| at the positions of OAP1 (a, d, g, and j), OAP2 (b, e, h, and k), and the EO crystal (c, f, i, and l) are plotted. The first row (a–c) shows the results of {electron energy, metal foil size, wavelength} = {250 MeV, 10 cm, 100 μ\mum}. The second row (d–f) shows the results of {250 MeV, 1 cm, 100 μ\mum}. The third row (g–i) shows the results of {250 MeV, 10 cm, 10 μ\mum}. The fourth row (j–l) shows the results of {10 MeV, 10 cm, 10 μ\mum}.

In addition, diffraction calculations were conducted in the short-wavelength region. The calculations for {250 MeV,10 μm}\{250\ \mathrm{MeV}, 10\ \mu\mathrm{m}\} and {10 MeV,10 μm}\{10\ \mathrm{MeV}, 10\ \mu\mathrm{m}\} are shown in Figs. 3(g–i) and 3(j–l), respectively. The diffraction effect was less noticeable at a wavelength of 10 μm10\ \mu\mathrm{m}, and the focus sizes at the EO crystal were smaller. With an electron energy of 250 MeV250\ \mathrm{MeV}, certain diffraction patterns remained. The diffraction patterns were invisible for an electron energy of 10 MeV10\ \mathrm{MeV} because the effective electron radius was only ∼200 μm\sim200\ \mu\mathrm{m}.

Analytic model based on Fraunhofer assumption

Although a detailed calculation based on the Huygens–Fresnel principle can provide relatively accurate diffraction results for an arbitrary setup, the process becomes time-consuming when the number of frequency components exceeds a few hundred and the electron energy spectra are broad. Thus, we examined the feasibility of using a simplified analytical model based on the Fraunhofer assumption. The derivation process is described in [34, 35]. To perform a quantitative calculation of the absolute field strength, we derived the TR field produced by a single electron at the imaging point in the SI unit as follows:

E0D(XD,YD)=−eϵ01λMv(XD,YD)ρDf(θm,γ,ζ)(14)E_0^D(X_D,Y_D)=-\frac{e}{\epsilon_0}\frac{1}{\lambda M v}\frac{(X_D,Y_D)}{\rho_D}f(\theta_m,\gamma,\zeta) \tag*{(14)}

where ρD=XD2+YD2\rho_D = \sqrt{X_D^2+Y_D^2}. θm=Rl/F\theta_m = R_l/F is the acceptance angle of the OAP and ζ=kρD/M\zeta= k\rho_D/M is the normalized distance from the center of the TR field to the calculation point in the detector plane. Further, M=F2/F1M = F_2/F_1 is the magnification of the imaging system. In this study, M=1M = 1. f(θm,γ,ζ)=∫0θmθ2(θ2+γ−2)J1(ζθ)dθf(\theta_m,\gamma,\zeta) = \int_0^{\theta_m} \frac{\theta^2}{(\theta^2+\gamma^{-2})}J_1(\zeta\theta)d\theta is a diffraction function defined by the optical system and the electron energy, where JJ is a Bessel function of the first kind. This integration can be performed numerically. When 1/γ≪θm1/\gamma\ll\theta_m, it is further simplified as follows [34]:

f(θm,γ,ζ)≈ζ−1[γ−1ζK1(γ−1ζ)−J0(ζθm)](15)f(\theta_m,\gamma,\zeta) \approx\zeta^{-1}[\gamma^{-1}\zeta K_1(\gamma^{-1}\zeta)-J_0(\zeta\theta_m)] \tag*{(15)}

The electric field formed by an electron slice was then calculated as follows:

ED(XD,YD)=g⊥∗E0D(16)E^D(X_D,Y_D)=g_\perp* E_0^D \tag*{(16)}

The following assumptions were made to obtain Eqs. (14),(15): (i) Fraunhofer approximation. The quadratic phase term in the source plane exp⁡[ik(Xs2+Ys2)/2F]\exp[ik(X_s^2+Y_s^2)/2F] was neglected, and the metal foil size was infinite. (ii) The distance between OAP1 and OAP2 is zero. An ideal thin lens was assumed, and intermediate diffraction was ignored. (An explanation for why the 2-OAP system can be geometrically treated as a thin-lens imaging system has been provided in Appendix B). (iii) The diameter of OAP1 acts as the only pupil in the system. (iv) The electrons possess high energy to satisfy the condition 1/γ≪θm1/\gamma\ll\theta_m. It is expected that the field strength values from the detailed Huygens–Fresnel calculation should be smaller than those from the simplified model, wherein several diffraction processes are not considered. Therefore, the errors generated in this approach should be assessed.

The calculation results for the same electron parameters as those in the previous section are shown in Figure 4. Comparisons of Figure 3(c), Figure 3(i), and Figure 3(l) with Figure 4(a), Figure 4(b), and Figure 4(c), respectively, revealed that the focus

Calculation results of the electric field magnitude at the EO crystal for three electron energy and wavelength combinations

Figure 4. Calculation results of ∣Ey(X,Y,f)∣|E_y(X,Y,f)| at the EO crystal based on an analytic model based on Fraunhofer assumption. Here, (a) shows the result of {electron energy, wavelength} = {250 MeV, 100 μ\mum}, (b) shows the result of {250 MeV, 10 μ\mum}, and (c) shows the result of {10 MeV, 10 μ\mum}.

shapes are almost identical over a large range of electron energies and wavelengths, though small errors exist. As our prediction, the peak values from the Huygens–Fresnel calculation were smaller than those of the analytical model, with errors of (7%, 0.47%, and 5.5%) in the cases of ({250 MeV, 100 μ\mum}, {250 MeV, 10 μ\mum}, and {10 MeV, 10 μ\mum}), respectively. The error in the case of {250 MeV, 100 μ\mum} primarily originated from the diffraction loss in the source plane and propagation. Whereas, the error for {10 MeV, 10 μ\mum} resulted from the assumption 1/γ≪θm1/\gamma\ll\theta_m. In the high-energy and short-wavelength regions, the errors were ignored.

Calculation of the OTR image

Before proceeding with the 3D calculations, we explain the calculation method for OTR images. OTR was used to determine the electron transverse bunch size. In the optical range, the wavelength was excessively short, which resulted in the diffraction difference between the Huygens–Fresnel principle and the Fraunhofer assumption being unnoticeable. Therefore, a simplified analytical model was used. The OTR image is an integrated TR intensity with a dimension “zz”. Therefore, the issue of coherence expressed by the form factor must be considered.

For a certain frequency, the TR field in the EO crystal is the sum of all electrons in the bunch, that is, the integration of the TR produced by all slices, as illustrated in Figure 2. The TR field of one frequency component in the EO crystal is expressed as,

ED=N∬dxbdybg∥(xb,yb)E0D(XD−xb,YD−yb)×∫dzbg∥(zb)exp⁡(iωzb/v)(17)E^D=N\iint dx_bdy_bg_\parallel(x_b,y_b)E_0^D(X_D-x_b,Y_D-y_b) \times\int dz_bg_\parallel(z_b)\exp(i\omega z_b/v) \tag*{(17)}

Here, EDE^D represents any {x,y}\{x,y\} component of the TR field and NN is the number of electrons. The integration along the zz direction is the longitudinal form factor

Fz=∫dzbg∥(zb)exp⁡(iωzb/v),F_z = \int dz_b g_{\parallel}(z_b)\exp(i\omega z_b/v),

where g∥(zb)g_{\parallel}(z_b) is the longitudinal distribution of the bunch. The term exp⁡(iωzb/v)\exp(i\omega z_b/v) is given in Eq. (58) in Appendix A. The intensity of the OTR is

IOTR=ϵ0μ0(∣ExD∣2+∣EyD∣2)/2,I_{\mathrm{OTR}} = \sqrt{\frac{\epsilon_0}{\mu_0}}\left(\lvert E_x^D\rvert^2 + \lvert E_y^D\rvert^2\right)/2,

which can be separated into an incoherent component IicohI_{\mathrm{icoh}} and a coherent component IcohI_{\mathrm{coh}} [40] as follows:

Iicoh=ϵ0μ0/2×N×[g⊥∗(∣E0,xD∣2+∣E0,yD∣2)](18)I_{\mathrm{icoh}} = \sqrt{\frac{\epsilon_0}{\mu_0}}/2 \times N \times\left[g_{\perp} \ast\left(\lvert E_{0,x}^D\rvert^2 + \lvert E_{0,y}^D\rvert^2\right)\right] \tag*{(18)}
Icoh=ϵ0μ0/2×N(N−1)×∣Fz∣2×(∣g⊥∗E0,xD∣2+∣g⊥∗E0,yD∣2)(19)I_{\mathrm{coh}} = \sqrt{\frac{\epsilon_0}{\mu_0}}/2 \times N(N-1) \times\lvert F_z\rvert^2 \times\left(\lvert g_{\perp} \ast E_{0,x}^D\rvert^2 + \lvert g_{\perp} \ast E_{0,y}^D\rvert^2\right) \tag*{(19)}

where μ0\mu_0 is the magnetic constant. The ratio of Icoh/IicohI_{\mathrm{coh}}/I_{\mathrm{icoh}} is strongly dependent on the electron number and form factor. In the optical wavelength region, the ratio was sensitive when the electron bunch had a femtosecond or sub-femtosecond bunch duration. The calculation results for Gaussian bunches with a duration of 1 fs are shown in Figure 5. As evident, IicohI_{\mathrm{icoh}} exhibited a shape similar to the original electron bunch profile (Figure 5(a) and Figure 5(c)), whereas IcohI_{\mathrm{coh}} exhibited a “donut” shape because of radial polarization and the symmetry of the electron transverse profile (Figure 5(b) and Figure 5(d)). In another calculation with a bunch duration of 2 fs, IcohI_{\mathrm{coh}} decreased by a factor of 10710^7, whereas the change in IicohI_{\mathrm{icoh}} was irrelevant with respect to the bunch duration.

Calculation results of the OTR intensity distribution

Figure 5. Calculation results of the OTR intensity distribution (arbitrary unit) at a wavelength of 800 nm. Initial transverse sizes of the Gaussian bunch are (σx,σy)=(50,50) μm(\sigma_x, \sigma_y) = (50, 50)\ \mu\mathrm{m}. The electron energy is 100 MeV and the charge is 32 pC. (a) and (b) show IicohI_{\mathrm{icoh}} and IcohI_{\mathrm{coh}} at an electron bunch duration of 1 fs. (c) and (d) show the line-outs along the XX axis with Y=0Y = 0 in (a) and (b), respectively.

With the number of electrons set as 2×1082 \times10^8 in this calculation, the peak value of IcohI_{\mathrm{coh}} was 2.6×1032.6 \times10^3 times higher than that of IicohI_{\mathrm{icoh}}. This indicates that, in the bunch, if there exists a femtosecond spike with 0.1% of the total charge (tens to hundreds of fC), the overall OTR intensity profile exhibits a coherent pattern, as shown in Figure 5(b). Such coherent OTR caused by femtosecond or sub-femtosecond spikes have been reported in both conventional accelerators [37] and LWFA [41].

When the OTR was incoherent, deconvolution was conducted to retrieve the electron transverse profile by directly using the point spread function ∣E0,xD∣2+∣E0,yD∣2\lvert E_{0,x}^D\rvert^2 + \lvert E_{0,y}^D\rvert^2, as explained in Eq. (18) and Ref. [34]. However, when the OTR exhibits a coherent pattern, straightforward deconvolution is not possible. Thus, to estimate transverse electron sizes, an empirical linear relationship

Xmax⁡=A+BσxX_{\max} = A + B\sigma_x

[38] was discovered by evaluating the peak positions of the lineout, as shown in Figure 5(d), where AA and BB are constants, Xmax⁡X_{\max} is the peak position in the OTR signal, and σx\sigma_x is the Gaussian bunch size. Therefore, to a certain extent, this method can be used to determine the electron bunch size. The reconstruction method for the fine structure of the original electron transverse profile from IcohI_{\mathrm{coh}} will be investigated elsewhere.

3D TR field at the EO crystal

With a TR field of single frequency denoted by Eq. (17), the 3D TR field can be obtained using the Fourier transform as follows:

E(XD,YD,t)=12π∫dωED(XD,YD,ω)exp⁡(−iωt)(20)E(X_D,Y_D,t) = \frac{1}{2\pi}\int d\omega E^D(X_D,Y_D,\omega)\exp(-i\omega t) \tag*{(20)}

Calculations were performed with an electron energy of 100 MeV, a charge of 32 pC, and a bunch duration of 20 fs (rms). The size of the transverse bunch was (50,50) μm(50, 50)\ \mu\mathrm{m}. The calculations dealt with the time range of (−0.5−0.5)(-0.5-0.5) ps. The frequency range was zero to a few hundred THz.

To better explain the 3D (X,Y,T)(X,Y,T) profile, we plotted three 2D contours, as shown in Figure 6. The spatial distribution of the maximum temporal TR value ∣Ey∣max⁡\lvert E_y\rvert_{\max} is shown in Figure 6(a). The strong area of the TR field was concentrated within a few hundred micrometers. The size of the concentrated area was related to the electron energy and transverse bunch sizes. The (T,Y)(T,Y) distribution of EyE_y is shown in Figure 6(b). The opposite values on both sides of Y=0Y = 0 resulted from the radial polarization of TR. The EO signals were primarily determined by this distribution. The (X,T)(X,T) distribution of EyE_y at y=−200 μmy = -200\ \mu\mathrm{m} is shown in Figure 6(c). The temporal profile of the TR field was not uniform along the

Image not extracted

Figure 6. Calculation results of the 3D TR field Ey(X,Y,T)E_y(X,Y,T). (a) shows the (X,Y)(X,Y) distribution of the maximum value of ∣Ey∣|E_y| in the third dimension TT. (b) shows the (T,Y)(T,Y) distribution of EyE_y at X=0X=0. (c) shows the (X,T)(X,T) distribution of EyE_y at Y=−200 μmY=-200\ \mu\mathrm{m}.

XX axis. Previously, when experiments of EO spatial decoding were conducted, the transverse field distributions were not considered. However, when the magnification is not sufficiently large and the electron bunch has a small transverse size, the spatial strength profile of the field should be counted when uncompromising accuracy is required.

For a better elaboration of the spatial broadening of the TR field in the imaging plane, temporal and frequency domain lineouts were plotted, as shown in Figure 7. The lineout plots for Y=−200 μmY=-200\ \mu\mathrm{m} and Y=−800 μmY=-800\ \mu\mathrm{m} illustrated in Figure 6(b) are shown in Figure 7(a). The lineouts at positions x=0x=0 and x=200 μmx=200\ \mu\mathrm{m} are illustrated in Figure 7(b). As evident, the field strength weakened and the duration was prolonged with an increase in the distance from the center of the field, both horizontally and vertically. The frequency distributions of the three points are shown in Figure 7(c). The frequency distribution was narrower and shifted toward the long-wavelength end at greater distances from the center. The results shown in Figure 7 indicate clear differences in the frequency compositions when measuring the field at different positions. Thus, the spatial distribution of the TR field should be considered for all forms of measurements, including temporal [23] and frequency [42] domain analyses.

Image not extracted

Figure 7. Lineouts of field profiles. (a) shows the temporal profiles at two vertical positions Y=−200 μmY=-200\ \mu\mathrm{m} and Y=−800 μmY=-800\ \mu\mathrm{m} in Figure 6(b). (b) shows the temporal profiles at two horizontal positions X=0 μmX=0\ \mu\mathrm{m} and X=200 μmX=200\ \mu\mathrm{m} in Figure 6(c). (c) shows the frequency domain profile of the TR field at three points (0,−200) μm(0,-200)\ \mu\mathrm{m} (blue), (0,−800) μm(0,-800)\ \mu\mathrm{m} (red), and (200,−200) μm(200,-200)\ \mu\mathrm{m} (green).

Comparison of 3D TR field calculations made using the two approaches

In Sections III.A and III.B, two approaches for calculating the image of the TR field: detailed diffraction based on the Huygens–Fresnel principle and an analytic model based on the Fraunhofer assumption for calculating, were elaborated. We observed slight differences in the monochromatic imaging calculations for various electron energies and wavelengths, as shown in Figure 3 and Figure 4. To confirm the possibility of adopting a less time-consuming approach in 3D calculations, the results of both approaches were compared.

The calculations from both approaches with different electron energies are plotted in Figure 8. The electron bunch parameters are as follows: charge = 32 pC, transverse beam size = (50,50) μm(50,50)\ \mu\mathrm{m}, and bunch duration = 20 fs (rms, gaussian). The TR field distributions obtained from both approaches were almost identical. With electron energies of both 20 and 200 MeV, the peak values of ∣Ey∣max⁡|E_y|_{\max} from the detailed calculations were only 3 % lower than those of the simplified analytic model. The minute difference necessitates the use of an analytical model when performing parameter fitting. Based on the calculations above and in the previous subsections, we conclude that the analytical model is appropriate in most cases. In the lateral sections, without special announcements, an analytic model based on the Fraunhofer approximation will be applied in the calculation of the 3D TR field.

Comparison of the 3D calculations of the $|E_y|_{\max}$ using two approaches for electron energies of 20 MeV and 200 MeV

Figure 8. Comparison of the 3D calculations of the ∣Ey∣max⁡|E_y|_{\max} using the two approaches with different electron energies. All the figures share the same colormap limit. (a) and (c) show the calculations of Huygens–Fresnel diffractions. (b) and (d) show the calculations using the analytic model based on Fraunhofer assumption. (a) and (b) show the results with an electron energy of 20 MeV. (c) and (d) show the results with an electron energy of 200 MeV.

Numerical Study of EO Spatial Decoding

The fundamental inline EO sampling process has been studied numerically in detail in [30]. Maximum phase retardation is achieved when the polarization of the probe laser, optical axis [−1,1,0][-1,1,0] of the crystal, and polarization of the external field are in the same direction.

Γ=2πn03dλ0r41ETR(21)\Gamma= \frac{2\pi n_0^3 d}{\lambda_0}r_{41}E_{TR} \tag*{(21)}

where n0n_0 is the refractive index of the central wavelength λ0\lambda_0 of the probe laser, r41r_{41} is the EO coefficient, and dd denotes the crystal thickness. Notably, Eq. (21) can only be used to approximately estimate the peak strength of the external field because the frequency-dependent response of the crystal is not included. Steffen et al. [29] proposed a near cross-polarization setup for measuring the shape of a TR field with good linearity when Γ\Gamma was small. As shown in Figure 1, a λ/4\lambda/4 plate was used to eliminate the residual birefringence caused by the EO crystal. The polarizer pair “S” and “P” are cross polarized to each other.

The λ/2\lambda/2 plate was slightly rotated by an angle θ2\theta_2, and the detected EO signal is calculated as,

Idet(θ2,Γ)=Ip2[1−cos⁡(Γ+4θ2)]+δextIp+B0(22)I_{\mathrm{det}}(\theta_2,\Gamma)=\frac{I_p}{2}\left[1-\cos(\Gamma+4\theta_2)\right]+\delta_{\mathrm{ext}}I_p+B_0 \tag*{(22)}

where B0B_0 is the dark image of the camera, δext\delta_{\mathrm{ext}} is the extinction ratio of the polarizer pair, and IpI_p is the original intensity profile of the probe. The background without an external TR field is expressed as follows:

B1=Ip2[1−cos⁡(4θ2)]+δextIp+B0(23)B_1=\frac{I_p}{2}\left[1-\cos(4\theta_2)\right]+\delta_{\mathrm{ext}}I_p+B_0 \tag*{(23)}

We conducted data processing of Isig=(Idet−B1)/(B1−B0)I_{\mathrm{sig}}=(I_{\mathrm{det}}-B_1)/(B_1-B_0) to eliminate the impact of nonuniformity of the original probe transverse profile as follows:

Isig=cos⁡(4θ2)−cos⁡(Γ+4θ2)1−cos⁡(4θ2)+2δext(24)I_{\mathrm{sig}}=\frac{\cos(4\theta_2)-\cos(\Gamma+4\theta_2)}{1-\cos(4\theta_2)+2\delta_{\mathrm{ext}}} \tag*{(24)}

For EO spatial decoding, the detailed EO signal generation process has rarely been investigated outside the geometric temporal mapping relationship:

cΔτ=tan⁡θpΔξ(25)c\Delta\tau=\tan\theta_p\Delta\xi \tag*{(25)}

where Δτ\Delta\tau is the temporal gap, ξ\xi is the displacement observed by the camera, and θp\theta_p denotes the incident angle of the probe laser beam on the surface of the EO crystal. When the dispersion of the TR field inside the crystal and the spatial distribution of the TR field are included, such a temporal mapping relationship lacks sufficient information to calculate the resulting EO signal shape. Thus, we conducted a detailed numerical study to apply EO spatial decoding to various situations. We arranged the elaboration from a simplified to a complicated case. The complexity of the calculation is dependent on the thickness of the crystal and spot size of the TR field in the image plane. Two main processes were involved in the calculation:

  1. Temporal elongation of the probe laser beam: Here, we considered the use of gallium phosphide (GaP) crystals. The broadening effect can be calculated by considering the group delay dispersion (GDD) with the knowledge of the refractive index curve in the optical range n(λ)=a1+a2λ2/(λ2−a3)n(\lambda)=\sqrt{a_1+a_2\lambda^2/(\lambda^2-a_3)}, where a1a_1, a2a_2, and a3a_3 are constants[29]. The central wavelength of the probe laser beam was λ0=800\lambda_0=800 nm. Assuming a Gaussian probe pulse with a duration of 10 fs (rms) and a flat phase profile in the frequency domain, the pulse shapes for various propagation depths are shown in Figure 9(a). At a depth of 20 μ\mum inside the GaP crystal, the shape exhibited minimal change. The probe pulse elongated upon further propagation inside the crystal. The curves in Figure 9(a) were calculated with the integrated energy conserved.

Image not extracted

Figure 9. Geometric explanation of the EO spatial decoding process. (a) shows the normalized probe intensity profiles at propagation depths of 0 (dotted black), 20 μ\mum (red), 100 μ\mum (green), and 200 μ\mum (blue). (b) illustrates the geometry of the walk-off between the TR field and the probe laser beam. The green and red solid lines show a timeline in the TR field and probe pulse when incident on a slice of the EO crystal, respectively. The dashed lines show those at the exit of the slice. The probe laser beam has incident and propagation angles of θp\theta_p and θp′\theta'_p, respectively. (c) shows how the existing probe duration should be considered in the calculation.

  1. Walk-off between the probe laser beam and the TR field inside the EO crystal: The TR field was normally incident on a slice of the EO crystal. Owing to the relative angle and velocity differences between the TR field

and the probe laser beam, a 2D geometry should be considered, as shown in Figure 9(b). A timeline in the TR field propagated from the entrance to the exit of the crystal slice (solid green to dashed green). Within the same period, a timeline in the probe pulse propagated from the solid line to the dashed red line. As EO spatial decoding examines the transverse profile of the probe, the points “A” and “A1” shared the same timing on the camera. However, the cross point (coding point) shifted from “A” to “B”, which introduced walk-off in both the probe laser beam (denoted by the region BA1‾\overline{BA1}) and the TR field (denoted by the region BA2‾\overline{BA2}). BA1‾\overline{BA1} caused smearing of the EO signal in the transverse probe profile, and BA2‾\overline{BA2} is a factor that must be considered when the strength of the TR field changes rapidly in the transverse direction.

EO spatial decoding in a simple 1D case

As shown in Figure 7, the TR fields in the temporal and frequency domains can be calculated at any spatial point on the imaging plane. The information regarding the frequency-dependent refractive index N(ω)=n(ω)+iκ(ω)N(\omega)=n(\omega)+i\kappa(\omega) and EO coefficient r41(ω)r_{41}(\omega) can be found in [30]. To further elaborate the process of EO signal generation, we separated the EO crystals into slices. Each slice jj had a thickness of Δz\Delta z and a propagation depth of zjz_j.

The smearing process is described in [43] in the general case considering that the TR field has an incident angle of θs\theta_s. The smearing factor was calculated as follows:

S=sin⁡θp+sin⁡θsvpsin⁡αcos⁡2θp′vs−vpcos⁡α+sin⁡θp′cos⁡θp′(26)S=\frac{\sin\theta_p+\sin\theta_s}{\frac{v_p\sin\alpha\cos^2\theta'_p}{v_s-v_p\cos\alpha}+\sin\theta'_p\cos\theta'_p} \tag*{(26)}

where θp′\theta'_p and θs′\theta'_s are the propagation angles of the probe and the TR field inside the crystal, respectively, α=θs′+θp′\alpha=\theta'_s+\theta'_p, vpv_p denotes the group velocity of the probe, and vs=c/n(ω)v_s=c/n(\omega) is the phase velocity of the TR field. Because θs=θs′=0\theta_s=\theta'_s=0, based on the relationship sin⁡θp=n0sin⁡θp′\sin\theta_p=n_0\sin\theta'_p, Eq. (26) is reduced to

S(ω)=c(1v∥−1vs)(27)S(\omega)=c\left(\frac{1}{v_{\parallel}}-\frac{1}{v_s}\right) \tag*{(27)}

where v∥=vpcos⁡θp′v_{\parallel}=v_p\cos\theta'_p denotes the probe speed component along the propagation direction of the TR field. For EO spatial decoding, the initial transverse profile of the probe laser beam was mapped as a time array τ\tau. For slice jj, the time table changed owing to the walk-off BA1‾\overline{BA1} as follows:

tj=τ+S×zj/c(28)t_j=\tau+S\times z_j/c \tag*{(28)}

Without considering the TR’s transverse distribution, we calculated only ETR0(ω)E^0_{TR}(\omega) at a certain spatial point (X,Y)(X,Y) at the entrance of the crystal. At a propagation depth of zjz_j inside the crystal, the TR field in the frequency domain was calculated as:

ETR,j(ω)=21+N(ω)exp⁡[−κ(ω)ωzj/c]ETR0(ω)(29)E_{TR,j}(\omega)=\frac{2}{1+N(\omega)}\exp[-\kappa(\omega)\omega z_j/c]E^0_{TR}(\omega) \tag*{(29)}

as their own time references. Here, 2/(1+N(ω))2/(1+N(\omega)) is the amplitude transmission coefficient based on the Fresnel’s law and κ(ω)ω/c\kappa(\omega)\omega/c is the absorption rate. The effective TR field was calculated by calculating the EO coefficient r41(ω)r_{41}(\omega) as follows:

ETR,jeff(ω)=r41(ω)ETR(ω)(30)E^{\mathrm{eff}}_{TR,j}(\omega)=r_{41}(\omega)E_{TR}(\omega) \tag*{(30)}

The EO effect was calculated in the time domain. The effective TR field ETR,jeff(τ)E^{\mathrm{eff}}_{TR,j}(\tau) was obtained using Fourier transformation ETR,jeff(τ)=12π∫exp⁡(−iωtj)ETR,jeff(ω)dωE^{\mathrm{eff}}_{TR,j}(\tau)=\frac{1}{2\pi}\int\exp(-i\omega t_j)E^{\mathrm{eff}}_{TR,j}(\omega)d\omega.

ETR,jeff(τ)=12π∫exp⁡(−iωτ)exp⁡[−iωzj(1v∥−1vs)]21+N(ω)exp⁡[−κ(ω)ωzj/c]ETR0(ω)r41(ω) dω(31)E_{TR,j}^{\mathrm{eff}}(\tau)=\frac{1}{2\pi}\int\exp(-i\omega\tau)\exp\left[-i\omega z_j\left(\frac{1}{v_{\parallel}}-\frac{1}{v_s}\right)\right]\frac{2}{1+N(\omega)}\exp[-\kappa(\omega)\omega z_j/c]E_{TR}^{0}(\omega)r_{41}(\omega)\,d\omega \tag*{(31)}

The phase retardation in slice jj was then calculated as,

ΔΓj(τ)=2πn03λ0ΔzETR,jeff(τ)(32)\Delta\Gamma_j(\tau)=\frac{2\pi n_0^3}{\lambda_0}\Delta zE_{TR,j}^{\mathrm{eff}}(\tau) \tag*{(32)}

By setting the slice number to infinity, the overall phase retardation is the sum of the contributions from all slices

retardation is the sum of the contributions from all slices Γ(τ)=∑jΔΓj(τ)\Gamma(\tau)=\sum_j\Delta\Gamma_j(\tau) and can be transformed into an integral as follows:

Γ(τ)=n03dλ0∫dω21+N(ω)ETR0(ω)r41(ω)×1d∫0dexp⁡[iω(N(ω)c−1v∥)z]dz(33)\Gamma(\tau)=\frac{n_0^3d}{\lambda_0}\int d\omega\frac{2}{1+N(\omega)}E_{TR}^{0}(\omega)r_{41}(\omega)\times\frac{1}{d}\int_0^d\exp\left[i\omega\left(\frac{N(\omega)}{c}-\frac{1}{v_{\parallel}}\right)z\right]dz \tag*{(33)}

Equation (32) expresses the phase retardation obtained using an infinitesimal slice of the probe laser beam. However, the probe laser beam had a longer pulse duration. We considered that the probe laser beam contained the maximum number of slices possible and calculated the overall phase retardation by summing all slices. This process is illustrated in Figure 9(c). Two slices, denoted as “P1” and “P2”, in the probe pulse had a time gap of Δtp\Delta t_p. In the probe laser beam with an incident angle of θp\theta_p, the same TR wavefront was encoded to the subsequent probe slice with a displacement of Δξp=cΔtp/tan⁡θp\Delta\xi_p=c\Delta t_p/\tan\theta_p on the camera chip. When using the temporal mapping relationship in Eq. (25), signal blurring occurred with a decoded time gap of Δτp=tan⁡θp/c×cΔtp/tan⁡θp=Δtp\Delta\tau_p=\tan\theta_p/c\times c\Delta t_p/\tan\theta_p=\Delta t_p. Similarly, if the probe had temporal slices with an index jj and an intensity profile at time I(tpj)I(t_p^j) in the time region between (−Tp,Tp)(-T_p,T_p), the total EO phase retardation is expressed as: Γtotal(τ)=∑jΓ(τ+tpj)I(tpj)/∑jI(tpj)\Gamma_{\mathrm{total}}(\tau)=\sum_j\Gamma(\tau+t_p^j)I(t_p^j)/\sum_j I(t_p^j). This was rewritten as an integral as follows:

Γtotal(τ)=∫−TpTpdtpf(tp)Γ(τ+tp)(34)\Gamma_{\mathrm{total}}(\tau)=\int_{-T_p}^{T_p}dt_p f(t_p)\Gamma(\tau+t_p) \tag*{(34)}

where f(tp)f(t_p) denotes the normalized temporal intensity profile of the probe laser beam. Equation (33) is in the form of a cross-correlation between the temporal profile of the probe laser beam and phase retardation of one probe slice, as denoted in Eq. (33). Mathematically, when the kernel profile is symmetrical around zero, similar to that in the case of a Gaussian-like profile, Eq. (34) is equivalent to a convolution.

Examples of the calculations are shown in Figure 10 for electron energies of {100,20}\{100, 20\} MeV and bunch durations of {20,50}\{20, 50\} fs (rms). Frequency-domain TR fields at two points (X,Y)=(0,−200)(X, Y) = (0, -200) μ\mum and (0,−800)(0, -800) μ\mum were used as inputs for EO signal generation. The electron transverse bunch sizes were (50,50)(50, 50) μ\mum, and Eq. (24) was used to calculate IsigI_{sig}. The probe laser beam was assumed to exhibit a Gaussian shape with a duration of 10 fs (rms), and the incident angle of the probe laser beam was θp=25∘\theta_p = 25^\circ. The oscillations in the IsigI_{sig} curves resulted from frequency-dependent phase mismatching.

Image not extracted

Figure 10. Calculated EO signals at points (X,Y)=(0,−200) μm(X,Y)=(0,-200)\,\mu\mathrm{m} (blue) and (0,−800) μm(0,-800)\,\mu\mathrm{m} (red) using the near cross-polarization setup with a 20-μm\mu\mathrm{m} crystal. (a) and (b) show the results with electron bunch durations of 20 fs (rms). (c) and (d) show the results with electron bunch durations of 50 fs (rms). (a) and (c) correspond to an electron energy of 100 MeV. (b) and (d) show the results with an electron energy of 20 MeV.

The following observations were obtained from Figure 10. (i) The visibility of oscillations is strongly dependent on the electron bunch duration. Fierce oscillations are observed for electron bunching duration of 20 fs. For electrons with a bunch duration of >50> 50 fs, the oscillations are indistinctive and the shapes of IsigI_{sig} are almost identical to the temporal shape of the TR field. (ii) The signals are broadened and weaker when the signal was measured at Y=−800Y = -800 μ\mum. With a lower electron energy, the signal intensity further decreases. (iii) The signal intensity ratio of I−200/I−800I_{-200}/I_{-800} varies for different electron bunch durations and electron energies. The features above indicate that, to monitor the electron bunch duration or

peak current, the spatial point at which the EO signal is measured must be identified.

Reminder on the adequate number of slices in EO sampling calculations

To manage the temporal elongation of the probe laser beam in a thick crystal, the EO crystal was separated into slices, as described above. A similar procedure was followed in [29, 30]. Here, the number of slices must be focused upon. We proceed with this explanation by introducing a parameter that measures the phase mismatching process: the averaged geometric response function ∣G∣|G|. The ∣G∣|G| value of the two approaches is calculated as

∣G∣integral=1d∫0dexp⁡(iΔkz) dz(35)|G|_{integral} = \frac{1}{d}\int_{0}^{d}\exp(i\Delta k z)\,dz \tag*{(35)}
∣G∣sum=1d∑jexp⁡(iΔkzj)×(d/Nslice)(36)|G|_{sum} = \frac{1}{d}\sum_{j}\exp(i\Delta k z_j)\times(d/N_{slice}) \tag*{(36)}

Equation (34) is the final integral of Eq. (33) for a thin crystal and Δk(ω)=ω(N(ω)c−1vl)\Delta k(\omega) = \omega\left(\frac{N(\omega)}{c} - \frac{1}{v_l}\right). Notably, Eq. (35) is a modification of the inline version reported in Ref. [30], which was obtained by changing the group velocity of the probe vpv_p to vlv_l, considering the relative angle between the probe and the TR field. However, for thick crystals, it is inadequate to consider the entire crystal as a single slice.

The average geometric response function is the sum of phase mismatches in each slice, as described in Eq. (36), where NsliceN_{slice} denotes the number of slices used in the calculations and dd denotes overall crystal thickness.

Figure 11 shows the results of the calculations for GaP crystals with thicknesses of 30 μ\mum (Figure 11(a) and Figure 11(c)) and 100 μ\mum (Figure 11(b) and Figure 11(d)). Cases with small NsliceN_{slice} had a slice thickness of 10 μ\mum, whereas cases with large NsliceN_{slice} had slice thickness of 0.25 μ\mum. When the number of slices was insufficient, ∣G∣sum|G|_{sum} differed significantly from ∣G∣integral|G|_{integral}, which resulted in fake responses in the high-frequency region. This comparison indicates that, to achieve an appropriate shape of the EO signal, the number of slices must be increased.

Averaged geometric response function with different number of slices

Figure 11. Averaged geometric response function with different number of slices. The results of ∣G∣integral|G|_{integral} and ∣G∣sum|G|_{sum} are denoted by blue dots and red curves, respectively. (a) and (b) correspond to cases with a small number of slices. (c) and (d) show the results from a large number of slices. (a) and (c) show the results from a 30-μ\mum crystal. (b) and (d) show the results from a 100-μ\mum crystal.

Using the information described above, we carefully examined the validity of “1D integral” calculations in a slightly thicker crystal with a thickness of 30 μ\mum. In this crystal, the probe laser beam was slightly elongated in the last 10 μ\mum. Figure 12 shows the results of the comparison between the “1D integral” and “1D sum” calculations. A total of 120 NsliceN_{slice} were utilized in the “1D sum” calculation and the probe elongation in each slice was calculated. In the “1D integral” calculation, the entire crystal was considered as a single slice. An unchanged probe shape was obtained by calculating the average probe profile of 120 slices. At electron bunch durations of 20 and 50 fs, no differences were observed between the two models. This conclusion is essential in the analysis of the experimental EO signal because the calculation with many slices is two orders of magnitude slower than the “1D integral” calculation. However, as this study utilized the numerical methodology, the notation “1D model” implies the “1D sum” model in lateral context for accuracy.

Comparison of the calculation results between the “1D integral” and “1D sum” models

Figure 12. Comparison of the calculation results between the “1D integral” and “1D sum” models. The red curves and black dots denote the calculation results from the “1D integral” and “1D sum” models, respectively. (a) shows the results with a bunch duration of 20 fs. (b) shows the results with a bunch duration of 50 fs.

Overall EO signals generated from a GaP crystal with a thickness of 30 $\mu$m determined using different calculation models

Figure 16. Overall EO signals generated from a GaP crystal with a thickness of 30 μ\mum determined using different calculation models. The field information is obtained at Y=−200Y=-200 μ\mum. (a) shows the calculation results with an electron bunch duration of 20 fs (rms). (b) shows the calculation results with an electron bunch duration of 50 fs (rms). The results from the “2D”, “TU” and “1D” models are illustrated by blue solid curves, red dashed, and black dotted curves, respectively.

EO spatial decoding in a general 2D case

In this study, the transverse TR strength distribution was ignored, as described. However, when the temporal scale of interest is longer, a larger transverse region must be calculated, where the transverse TR field distribution may have an impact. Here, the TR field distribution plotted in Figure 6(c) was used as the input.

The EO crystal was divided into thin slices. For example, a GaP crystal with a thickness of 30 μ\mum was separated into 120 slices. Each slice had a thickness of Δz=0.25\Delta z=0.25 μ\mum. The propagation depth at each slice was zj=jΔzz_j=j\Delta z. The effective 2D TR fields ETReff,j(XTR,ZTR)E_{\mathrm{TR}}^{\mathrm{eff},j}(X_{\mathrm{TR}},Z_{\mathrm{TR}}) in the time domain and the 2D probe intensities Ipj(Xp,Zp)I_p^j(X_p,Z_p) were calculated for each slice. Here, ZZ and ZpZ_p are ZTR=−ctTRZ_{\mathrm{TR}}=-ct_{\mathrm{TR}} and Z=−ctpZ=-ct_p, respectively. further, (XTR,ZTR)(X_{\mathrm{TR}},Z_{\mathrm{TR}}), and (Xp,Zp)(X_p,Z_p) are the coordinates that co-propagated with the TR and probe laser beams. Notably, the calculation of ETReff,j(XTR,ZTR)E_{\mathrm{TR}}^{\mathrm{eff},j}(X_{\mathrm{TR}},Z_{\mathrm{TR}}) already included the EO effect and longitudinal phase mismatch.

The calculation procedure for one slice of the EO crystal is illustrated in Figure 13. The propagation depth was

Schematic showing the calculation procedure for 2D EO spatial decoding

Figure 13. Schematic showing the calculation procedure for 2D EO spatial decoding. (a) shows the 2D probe intensity distribution at coordinates (Xp,Zp)(X_p, Z_p). (b) shows the effective TR field inside the crystal at coordinates (XTR,ZTR)(X_{TR}, Z_{TR}). (c) shows the interpolated TR field at coordinates (XTR,ZTR)(X_{TR}, Z_{TR}). (d) shows the pattern of the interpolated effective TR field by coordinate transformation from (XTR,ZTR)(X_{TR}, Z_{TR}) to (Xp,Zp)(X_p, Z_p).

zj=25z_j=25 μ\mum. The 2D intensity distribution of the probe laser beam with coordinates (Xp,Zp)(X_p,Z_p) is shown in Figure 13(a). Because the transverse intensity distribution of the probe was excluded using Eq. (24), the transverse profile of the probe along XpX_p was set to be uniform. Further, the probe intensity was normalized in the ZpZ_p (tpt_p) direction and calculated, including the GDD. The effective 2D TR field in the same slice is shown in Figure 13(b).

A mesh grid for interpolation was calculated for each slice. We wish to clarify that coordinate transformation is not simply a rotation of (Xp,Zp)(X_p,Z_p). The relative propagation between the TR pulse and the probe laser beam should be considered for the EO effect occurring in a certain slice zjz_j. The geometry is shown in Figure 14. By including the transverse shift and longitudinal phase mismatch, the two coordinates (Xp,Zp)(X_p,Z_p) and (XTR,ZTR)(X_{\mathrm{TR}},Z_{\mathrm{TR}}) were set to have the same origin, OO (0, 0). Point “H” denotes the point where the EO effect occurred at an earlier timing, contributed by point “A” in the probe laser beam and point “B” in the effective TR field. Thus, we obtain the relationship HA‾=HB‾\overline{HA}=\overline{HB}. When OC‾=Xp\overline{OC}=X_p and AC‾=Zp\overline{AC}=Z_p, we showed that OH‾=Xp/cos⁡θp\overline{OH}=X_p/\cos\theta_p and HA‾=HB‾=Xp⋅tan⁡θp+Zp\overline{HA}=\overline{HB}=X_p\cdot\tan\theta_p+Z_p. Furthermore, by subtracting the relative transverse shift d⋅tan⁡θp′d\cdot\tan\theta'_p, the interpolation coordinates were expressed using Eq. (37).

Schematic showing coordinate transformation when performing the 2D EO calculation

Figure 14. Schematic showing coordinate transformation when performing the 2D EO calculation. “O” represents the origin of the coordinates. “A” (Xp,Zp)(X_p, Z_p) is a point in the probe laser. “B” (Xinterp,Zinterp)(X_{interp}, Z_{interp}) is the point in the effective TR field meeting with point “A” in the crystal slice zjz_j.

Xinterp=Xp/cos⁡θp−d⋅tan⁡θp′Zinterp=Xptan⁡θp+Zp(37)\begin{aligned} X_{\mathrm{interp}} &= X_p/\cos\theta_p-d\cdot\tan\theta'_p \\ Z_{\mathrm{interp}} &= X_p\tan\theta_p+Z_p \tag*{(37)} \end{aligned}

where θp′\theta'_p denotes the propagation angle of the probe beam inside the crystal. Subsequently, a 2D interpolation of ETReff,j(Xinterp,Zinterp)E_{TR}^{\mathrm{eff},j}(X_{\mathrm{interp}}, Z_{\mathrm{interp}}) was conducted in the region determined using Eq. (37). The interpolated TR field distribution is illustrated in Figure 13(c). Next, we transformed ETReff,j(Xinterp,Zinterp)E_{TR}^{\mathrm{eff},j}(X_{\mathrm{interp}}, Z_{\mathrm{interp}}) into the probe laser coordinates (Xp,Zp)(X_p, Z_p), as shown in Figure 13(d).

Subsequently, we calculated the phase retardation in each pixel as Γj(Xp,Zp)=2πn03Δd/λ0×Ijp(Xp,Zp)ETReff,j(Xp,Zp)\Gamma_j(X_p, Z_p) = 2\pi n_0^3 \Delta d/\lambda_0 \times I_j^p(X_p, Z_p)E_{TR}^{\mathrm{eff},j}(X_p, Z_p), which is the product of Figure 13(a) and Figure 13(d). A 2D distribution of Γ\Gamma is shown in Figure 15(a). The phase retardation profile Γj(Xp)\Gamma_j(X_p) along XpX_p was then calculated by accumulating the results shown in Figure 15(a) in the ZpZ_p direction. The EO signal contributed by this slice was calculated using Eq. (24). Earlier timing corresponded to larger ZTRZ_{TR} and XpX_p in Figure 14. The timetable was arranged as t=−Xptan⁡θp/ct=-X_p\tan\theta_p/c. The EO signal from one slice is shown in Figure 15(b). The peak position of the signal was at a timing earlier than zero because the group velocity of the probe laser beam was smaller than the phase velocity of the TR field inside the EO crystal. In this article, without special clarification, the peak of the EO signal is shifted to “zero” timing.

EO signal generation in one slice

Figure 15. EO signal generation in one slice. (a) shows the 2D phase retardation distribution at coordinates (Xp,Zp)(X_p,Z_p). (b) shows the accumulated EO signal in one slice in the near cross-polarization setup.

The information described above indicates the way EO signal generation is observed within one slice in a 2D geometry. The overall EO signal was calculated in three steps: (i) calculation of the accumulated phase retardation Γj(Xp)\Gamma_j(X_p) in each slice, (ii) calculation of the overall phase retardation as Γ(Xp)=∑jΓj(Xp)\Gamma(X_p)=\sum_j\Gamma_j(X_p), and (iii) calculation of the EO signal using Eq. (24).

Figure 16 shows the 2D EO spatial decoding results at the vertical position Y=−200 μmY=-200\ \mu\mathrm{m}. We performed the calculations with three different models: (i) “2D” (blue curve) implies the 2D EO calculation by considering the transverse TR field strength distribution; (ii) “TU” (red dot) implies the 2D EO calculation assuming that the TR field is transversely uniform; and (iii) “1D” (black dashed line) denotes the analytical model described in Sec. IV. A. Γj\Gamma_j was calculated for each slice using Eqs. (33) and (34).

The calculations revealed interesting results. (i) The results from “TU” and “1D” were identical, indicating that our approach for the 2D EO calculation is adequate. (ii) For a slightly longer bunch duration of 50 fs, the difference between the “2D” and “TU” was unnoticeable. (iii) For a very short bunch duration of 20 fs, determining a difference around the main peak of the signal was challenging. However, the amplitudes of the oscillations at later times were slightly smaller. Whereas, for a very long electron bunch, although no calculations were performed, we expected visible differences between the “2D” and “1D” models. In the case of LWFA, as the electron bunches have duration of a few fs to tens of fs, with such small errors, the application of the “1D” model should provide sufficient results when analyzing the EO signal around the main peak.

EO spatial decoding signal of temporally chirped electron bunches

Using the calculation method established above, we investigated electron bunches with multiple energy components. Typically, electron bunches with energy spreads exhibit chirps in the longitudinal phase space (LPS). We addressed this issue by separating the electrons into energy slices corresponding to different timings. For simplicity, a linear energy chirp with an energy range of 20–300 MeV was assumed. For electron slice jj, the timing was δtj=chirp⁡⋅(Ej−160)\delta t_j=\operatorname{chirp}\cdot(E_j-160) and the charge weight was ηj\eta_j. The longitudinal form factor was calculated using the Fourier transform Fzj(ω)=∫exp⁡(iωt)×exp⁡[−(t−δtj)2/2σt02]dtF_z^j(\omega)=\int\exp(i\omega t)\times\exp[-(t-\delta t_j)^2/2\sigma_{t0}^2]dt. The result of this integral was obtained as

Fzj(ω)=exp⁡(−ω2σz022v2+iωδzjv)(38)F_z^j(\omega)=\exp\left(-\frac{\omega^2\sigma_{z0}^2}{2v^2}+\frac{i\omega\delta z_j}{v}\right) \tag*{(38)}

for relativistic electrons v≈cv\approx c. Each slice was assumed to have the same slicing bunch duration of σt0=10\sigma_{t0}=10 fs, corresponding to a length of σz0=cσt0\sigma_{z0}=c\sigma_{t0}. With the relative center timing of each slice set to δtj\delta t_j, we defined δzj=cδtj\delta z_j=c\delta t_j. We assessed the signals from “2D” EO calculations at a vertical distance of YD=−200 μmY_D=-200\ \mu\mathrm{m}. The electron energy spectrum of a two-temperature (“2T”) distribution dN/dE∝1/T1exp⁡(−E/T1)+1/T2exp⁡(−E/T2)dN/dE\propto1/T_1\exp(-E/T_1)+1/T_2\exp(-E/T_2) was evaluated, with T1=20T_1=20 MeV and T2=300T_2=300 MeV. Examples of temporally chirped electron bunches are shown in Figure 17. Figure 17(a) shows the energy distributions (blue) of the “2T” model and a temporal chirp (red) of 0.2 fs/MeV. The 2D plot of the LPS and the current of a two-temperature electron bunch with a chirp of 0.2 fs/MeV is illustrated in Figure 17(b). Using the field expressions presented in Eq. (14), the frequency-domain field component is the sum of contributions from each electron energy component and the corresponding Fzj(ω)F_z^j(\omega), and is calculated as follows:

Longitudinal energy chirp and current profiles

Figure 17. Longitudinal energy chirp and current profiles. (a) The blue line illustrates the two-temperature energy distribution. The red line shows the slice timings of a positive chirp of 0.2 fs/MeV. (b) shows the 2D plot of the LPS of the two-temperature linear-chirped electron bunch. The red curve shows the current profile.

ED(XD,YD,ω)=∑jηjE0D(XD,YD,γj,ω)Fzj(ω)(39)E^D(X_D,Y_D,\omega)=\sum_j\eta_jE_0^D(X_D,Y_D,\gamma_j,\omega)F_z^j(\omega) \tag*{(39)}

To verify the impact of LPS on the EO signal, we compared the chirped and non-chirped electron bunches with a same current profile and overall charge. The normalized longitudinal profile was retrieved from the current profile, as shown in Figure 17(b). Subsequently, we calculated the longitudinal form factor Fz(ω)F_z(\omega) by performing Fourier transformation. In the non-chirped case, Fz(ω)F_z(\omega) was identical for all electron energy components. The field strengths EyE_y are plotted in Figure 18(a). The calculated EO signals from the 30-μm\mu\mathrm{m} GaP crystal are shown in Figure 18(b) and Figure 18(c). Chirps of 0.1 and 0.2 fs/MeV corresponded to temporal spans of 28 and 56 fs, respectively. The field from the chirped electron bunch exhibited a gentle rising edge because the high-energy electrons resided at subsequent timings. However, this small difference did not affect the shape of the EO signals. As shown in Figure 18(b–Figure 18c), despite the slight differences in the amplitudes, the shapes of the EO signals were almost identical.

Impact of temporal energy chirp on the EO signals

Figure 18. Impact of temporal energy chirp on the EO signals. The blue and red curves illustrate the results of chirped and nonchirped cases, respectively. (a) shows the field strength profiles at (XD,YD)=(0,−200) μm(X_D,Y_D)=(0,-200)\,\mu\mathrm{m}. (b) and (c) show the EO signals from current profiles with a chirp of 0.1 and 0.2 fs/MeV, respectively.

These calculations demonstrate that the current profile plays a more important role than the temporal energy chirp in the shapes of the EO signals. When the LPS is unclear, a non-chirped electron bunch is assumed to be sufficient for calculating the longitudinal current distribution.

Noise Introduced by the TR When the Electrons Hit OAP1

In the experimental setup illustrated in Figure 1, electrons passing through the metal foil hit the gold surface of OAP1, causing secondary TR noise. Thus, to remove this noise, the insertion of a bending magnet between the metal foil and OAP1 is recommended. Occasionally, to achieve better spatial resolution, the focal length of OAP1 is set as short, which renders the insertion of a magnet difficult. Here, we evaluated the strength of the TR field produced by OAP1. Figure 19(a) illustrates the calculation process. The scattering caused by the metal foil was calculated using the following equation that is dependent on the composition of the metal, thickness, and electron energy [44]:

Calculation geometry of the TR from OAP1 and beam size of the scattered electrons at the position of OAP1

Figure 19. (a) Calculation geometry of the TR from OAP1. TR generated by OAP1 has a plane wave front after OAP1 and is transported to OAP2 with diffraction. (b) Beam size of the scattered electrons at the position of OAP1.

θ0=13.6MeVβcpzxX0[1+0.038ln⁡(xX0)](40)\theta_0 = \frac{13.6\mathrm{MeV}}{\beta c p} z \sqrt{\frac{x}{X_0}}\left[1+0.038\ln\left(\frac{x}{X_0}\right)\right] \tag*{(40)}

where θ0\theta_0 is the rms divergence of the scattered beam, βc\beta c and pp are the velocity and momentum of the electrons, respectively, X0X_0 denotes the radiation length of the material, and xx denotes the thickness of the material. With a propagation distance of FF to OAP1, the electron beam

size was r1=r02+(θ0F)2r_1=\sqrt{r_0^2+(\theta_0F)^2}, where r0r_0 is the beam size at the position of the metal foil. For alloys such as stainless steel, the overall radiation length can be estimated as 1/X0=∑jwj/Xj1/X_0=\sum_j w_j/X_j, where the jjth element has a weight of wjw_j and a radiation length of XjX_j. The radiation length of each element can be found in the NIST database [45]. The weights of the elements of a material are also obtained from various databases. For example, we selected SUS304 stainless steel as the material for the metal foil [46] with a thickness of 100 μ\mum, an initial beam size of r0=50 μr_0=50\,\mum, and F=190F=190 mm. The r1r_1 for various electron energies at OAP1 are plotted in Figure 19(b). The size of the electron beams increased to several millimeters when the electrons had lower energies. For electrons with energies of 20 and 200 MeV, the beam sizes at OAP1 were 7623 μ\mum and 780 μ\mum, respectively, resulting in decreased charge densities.

The electron bunch on the metal foil was considered as the point source. The scattered electrons traversed OAP1 with phases forming a spherical wavefront. Thus, the Coulomb field of the electrons also exhibited a spherical phase. The phase difference on a plane perpendicular to the direction of propagation was described as Δϕ=k(F2+ρ2−F)≈kρ2/2F\Delta\phi=k(\sqrt{F^2+\rho^2}-F)\approx k\rho^2/2F. After reflection from OAP1, the spherical phase was corrected using the transform function in Eq. (9). The TR emitted from OAP1 was calculated as follows:

TR field strengths at the EO crystal

Figure 20. TR field strengths at the EO crystal. (a) TR generated from OAP1 with electron energy of 20 MeV. (b) TR generated from metal foil with electron energy of 20 MeV. (c) TR generated from OAP1 with electron energy of 200 MeV. (d) TR generated from metal foil with electron energy of 200 MeV.

EOAP1lr1=(g⊥OAP1∗ES)×Pl(41)E^{\mathrm{lr1}}_{\mathrm{OAP1}} = \left(g^{\mathrm{OAP1}}_{\perp} * E^{S}\right) \times P_l \tag*{(41)}

where g⊥OAP1g^{\mathrm{OAP1}}_{\perp} is the transverse distribution of the scattered electron beam at OAP1 and PlP_l is the pupil defined by the OAP. ESE^{S} was calculated using Eq. (1). The procedure described in § 3.A was followed for calculating lateral Huygens–Fresnel diffractions in the optical system.

For a fair comparison, we calculated the TR fields at the position of the EO crystal originating from two sources: the metal foil and OAP1. The TR generated from OAP1 with electron energies of 20 and 200 MeV are shown in Figs. 20(a) and 20(c), respectively. The corresponding results of the TR generated from the metal foil are shown in Figs. 20(b) and 20(d), respectively. With an electron energy of 20 MeV, the TR field generated from OAP1 was three orders of magnitude smaller than that generated from the metal foil. Whereas, at a higher electron energy of 200 MeV, the TR field generated from OAP1 was six times smaller than that generated from the metal foil.

Apparently, a smaller energy corresponds to a larger scattering angle. This results in a smaller charge density at the position of OAP1. If most of the electron energy is concentrated at approximately 100 MeV or a few tens of MeV, the noise TR source from OAP1 can be ignored. In the experiment, by measuring the electron energy spectrum, the impact of such noise was examined by performing this calculation, including the contributions of all energy components. Notably, temporal elongation of the electron bunches owing to energy spread was not considered. Thus, the noise should be even weaker when calculating the bunch elongation.

Discussion and Summary

In this study, the shapes of the signals in the EO spatial decoding setup were calculated at arbitrary positions in the image plane. We found that the duration and oscillation behavior of the EO signals varied with parameters such as the electron energy, bunch duration, and transverse beam size. Even with the same electron bunch parameters, the EO signal was broadened further from the center of the TR field. This behavior is similar to cases wherein Coulomb fields were measured [26]. Thus, we did not intend to provide a quick one-to-one correspondence between the duration of the main peak of the EO signal and the original electron bunch duration. Using the methods described herein, such correlations can be identified with specific electron bunch parameters. Spatially resolved detection is strongly recommended when conducting temporal or spectral measurements of a TR field using an imaging system. Furthermore, it is necessary to determine the position of the spatial point at which the experimental signals are measured.

In summary, we conducted a systematic numerical study of EO spatial decoding of TR from relativistic electron bunches. 3D TR field was determined using both a detailed calculation based on the Huygens–Fresnel principle and a simplified analytical model based on Fraunhofer assumption. The results suggest that the simplified analytical model is sufficient to perform such polychromatic calculations with considerable accuracy. For EO spatial decoding, we discussed the process of EO signal generation using both 1D and 2D models. The 1D model was concluded to be sufficient for quick data analysis. In addition, we demonstrated the minimal impact of the temporal energy chirp on the shape of the EO signal. Further, we proposed a method to estimate the noise level for unwanted TRs created by reflection optics. Therefore, this study will be useful for investigating the 3D charge-density profiles of ultrafast electron bunches in both LWFA and conventional accelerators.

ACKNOWLEDGMENTS

We are grateful for the encouragement provided by Dr. Y. Sano, and Dr. N. Kumagai. We thank Dr. J. K. Koga for providing valuable insights into the current research topic. This work was funded by the JST-Mirai Program, Japan (Grant No. JPMJMI17A1); the Grant-in-Aid for Early-Career Scientists (Grant Nos. JP21K17998 and JP23K17152); Grant-in-Aid for Scientific Research (C) from JSPS KAKENHI, Japan (Grant No. JP22K12665); and the QST President’s Strategic Grant (Exploratory Research), Japan.

Formulation of the electric field of transition radiation in SI units

Herein, the self-field expression for a single electron is derived. Similar derivations can be found in several textbooks and literature on Gaussian units [47, 48, 49]. We rewrote the formalization in SI units. Maxwell’s equations in vacuum are as follows:

∇⋅E=ρϵ0\nabla\cdot\mathbf{E} = \frac{\rho}{\epsilon_0}
∇⋅B=0\nabla\cdot\mathbf{B} = 0
∇×E=−∂B∂t\nabla\times\mathbf{E} = -\frac{\partial\mathbf{B}}{\partial t}
∇×B=μ0(J+ϵ0∂E∂t)(42)\nabla\times\mathbf{B} = \mu_0\left(\mathbf{J}+\epsilon_0\frac{\partial\mathbf{E}}{\partial t}\right) \tag*{(42)}

The scalar potential φ\varphi and vector potential A\mathbf{A} are expressed as,

B=∇×A\mathbf{B} = \nabla\times\mathbf{A}
E=−∇φ−∂A∂t(43)\mathbf{E} = -\nabla\varphi-\frac{\partial\mathbf{A}}{\partial t} \tag*{(43)}

The Lorentz Gauge equation is expressed as,

∇⋅A+1c2∂φ∂t=0(44)\nabla\cdot\mathbf{A}+\frac{1}{c^2}\frac{\partial\varphi}{\partial t}=0 \tag*{(44)}

Via (42) and (43) and (44), with c=1/ϵ0μ0c = 1/\sqrt{\epsilon_0\mu_0}, the wave equations can be derived as:

(∇2−1c2∂2∂t2)φ(r,t)=−ρ(r,t)ϵ0\left(\nabla^2-\frac{1}{c^2}\frac{\partial^2}{\partial t^2}\right)\varphi(\mathbf{r},t)=-\frac{\rho(\mathbf{r},t)}{\epsilon_0}
(∇2−1c2∂2∂t2)A(r,t)=−μ0J(r,t)(45)\left(\nabla^2-\frac{1}{c^2}\frac{\partial^2}{\partial t^2}\right)\mathbf{A}(\mathbf{r},t)=-\mu_0\mathbf{J}(\mathbf{r},t) \tag*{(45)}

Here, the variables (φ,A,ρ,(\varphi,\mathbf{A},\rho, and J)\mathbf{J}) are expressed in space and time coordinates (r(\mathbf{r} and t)t), where the instant charge, current, and displacement of a single electron are expressed as follows:

ρ(r,t)=−eδ(r−r(t))\rho(\mathbf{r},t)=-e\delta(\mathbf{r}-\mathbf{r}(t))
J(r,t)=−evδ(r−r(t))\mathbf{J}(\mathbf{r},t)=-e\mathbf{v}\delta(\mathbf{r}-\mathbf{r}(t))
r(t)=vt(46)\mathbf{r}(t)=\mathbf{v}t \tag*{(46)}

To avoid discrepancies caused by different conventions of Fourier transformation in the angular frequency, we used the standard Fourier transformation as follows:

g1(r,t)=∫df∫d3ν~ g2(ν~,f)exp⁡[i2π(ν~⋅r−ft)]g_1(\mathbf{r},t)=\int df\int d^3\tilde{\nu}\,g_2(\tilde{\boldsymbol{\nu}},f)\exp[i2\pi(\tilde{\boldsymbol{\nu}}\cdot\mathbf{r}-ft)]
g2(ν~,f)=∫dt∫d3r g1(r,t)exp⁡[−i2π(ν~⋅r−ft)](47)g_2(\tilde{\boldsymbol{\nu}},f)=\int dt\int d^3\mathbf{r}\,g_1(\mathbf{r},t)\exp[-i2\pi(\tilde{\boldsymbol{\nu}}\cdot\mathbf{r}-ft)] \tag*{(47)}

where (ν~,f)(\tilde{\boldsymbol{\nu}},f) and (r,t)(\mathbf{r},t) are the reciprocal ν~=k/2π\tilde{\boldsymbol{\nu}}=\mathbf{k}/2\pi and f=ω/2πf=\omega/2\pi. By performing Fourier transformations on both sides of (45), using the relationships in (47), the wave equations in the frequency domain are derived as,

(ν~2−f2c2)φ(ν~,f)=ρ(ν~,f)4π2ϵ0\left(\tilde{\nu}^2-\frac{f^2}{c^2}\right)\varphi(\tilde{\boldsymbol{\nu}},f)=\frac{\rho(\tilde{\boldsymbol{\nu}},f)}{4\pi^2\epsilon_0}
(ν~2−f2c2)A(ν~,f)=J(ν~,f)4π2ϵ0c2(48)\left(\tilde{\nu}^2-\frac{f^2}{c^2}\right)\mathbf{A}(\tilde{\boldsymbol{\nu}},f)=\frac{\mathbf{J}(\tilde{\boldsymbol{\nu}},f)}{4\pi^2\epsilon_0c^2} \tag*{(48)}

where ρ(ν~,f)\rho(\tilde{\boldsymbol{\nu}},f) and J(ν~,f)\mathbf{J}(\tilde{\boldsymbol{\nu}},f) are derived using Eqs. (A5) and (A6) as

ρ(ν~,f)=−eδ(f−ν~⋅v)\rho(\tilde{\boldsymbol{\nu}},f)=-e\delta(f-\tilde{\boldsymbol{\nu}}\cdot\mathbf{v})
J(ν~,f)=−evδ(f−ν~⋅v)(49)\mathbf{J}(\tilde{\boldsymbol{\nu}},f)=-e\mathbf{v}\delta(f-\tilde{\boldsymbol{\nu}}\cdot\mathbf{v}) \tag*{(49)}

The scalar and vector potentials of the field in the (k,ω)(\mathbf{k},\omega) domain are obtained as follows:

φ(ν~,f)=−e(2π)2ϵ0δ(f−ν~⋅v)ν~2−f2/c2\varphi(\tilde{\boldsymbol{\nu}},f)=-\frac{e}{(2\pi)^2\epsilon_0}\frac{\delta(f-\tilde{\boldsymbol{\nu}}\cdot\mathbf{v})}{\tilde{\nu}^2-f^2/c^2}
A(ν~,f)=−ev(2π)2ϵ0c2δ(f−ν~⋅v)ν~2−f2/c2(50)\mathbf{A}(\tilde{\boldsymbol{\nu}},f)=-\frac{e\mathbf{v}}{(2\pi)^2\epsilon_0c^2}\frac{\delta(f-\tilde{\boldsymbol{\nu}}\cdot\mathbf{v})}{\tilde{\nu}^2-f^2/c^2} \tag*{(50)}

Using the relationships in (43), we obtain

E(ν~,f)=i2πfA(ν~,f)−i2πν~φ(ν~,f)(51)\mathbf{E}(\tilde{\boldsymbol{\nu}},f)=i2\pi f\mathbf{A}(\tilde{\boldsymbol{\nu}},f)-i2\pi\tilde{\boldsymbol{\nu}}\varphi(\tilde{\boldsymbol{\nu}},f) \tag*{(51)}

The formula for the electric field E(k,ω)E(\mathbf{k},\omega) is derived as follows:

E(ν~,f)=−ie2πϵ0fv/c2−ν~ν~2−f2/c2δ(f−ν~⋅v)(52)\mathbf{E}(\tilde{\boldsymbol{\nu}},f)=-i\frac{e}{2\pi\epsilon_0}\frac{f\mathbf{v}/c^2-\tilde{\boldsymbol{\nu}}}{\tilde{\nu}^2-f^2/c^2}\delta(f-\tilde{\boldsymbol{\nu}}\cdot\mathbf{v}) \tag*{(52)}

For simplicity, we considered electron propagation along the z-axis. We have v=(0,0,v)\mathbf{v}=(0,0,v) and f=ν~⋅v=ν~zvf=\tilde{\boldsymbol{\nu}}\cdot\mathbf{v}=\tilde{\nu}_zv, where ν~=(ν~x,ν~y,ν~z)\tilde{\boldsymbol{\nu}}=(\tilde{\nu}_x,\tilde{\nu}_y,\tilde{\nu}_z). With the property of the delta function δ(ax)=δ(x)/∣a∣\delta(ax)=\delta(x)/|a|, Eq. (52) is rewritten as follows:

E(ν~,f)=ie2πϵ0vδ(f/v−ν~z)(ν~x,ν~y,ν~z/γ2)ν~x2+ν~y2+ν~z2/γ2(53)\mathbf{E}(\tilde{\nu},f)=i\frac{e}{2\pi\epsilon_{0}v}\delta(f/v-\tilde{\nu}_{z})\frac{(\tilde{\nu}_{x},\tilde{\nu}_{y},\tilde{\nu}_{z}/\gamma^{2})}{\tilde{\nu}_{x}^{2}+\tilde{\nu}_{y}^{2}+\tilde{\nu}_{z}^{2}/\gamma^{2}} \tag*{(53)}

Thus, the frequency-domain electric field in space can

be obtained using the integral in Eq. (54), with r=(x,y,z)\mathbf{r}=(x,y,z). As the longitudinal component of the field was weaker than the transverse component by a factor of 1/γ21/\gamma^{2}, we focused on analyzing the transverse component of the electric field in this study. The (Ex,Ey)(E_{x},E_{y}) components were calculated using Eq. (55).

E(r,f)=ie2πϵ0v∫d3ν~exp⁡[i2π(ν~xx+ν~yy+ν~zz)]δ(f/v−ν~z)(ν~x,ν~y,ν~z/γ2)ν~x2+ν~y2+ν~z2/γ2(54)\mathbf{E}(\mathbf{r},f)=i\frac{e}{2\pi\epsilon_{0}v}\int d^{3}\tilde{\nu}\exp[i2\pi(\tilde{\nu}_{x}x+\tilde{\nu}_{y}y+\tilde{\nu}_{z}z)]\delta(f/v-\tilde{\nu}_{z})\frac{(\tilde{\nu}_{x},\tilde{\nu}_{y},\tilde{\nu}_{z}/\gamma^{2})}{\tilde{\nu}_{x}^{2}+\tilde{\nu}_{y}^{2}+\tilde{\nu}_{z}^{2}/\gamma^{2}} \tag*{(54)}
Ex,y(r,f)=ie2πϵ0vexp⁡(i2πfz/v)∬dν~xdν~yexp⁡[i2π(ν~xx+ν~yy)](ν~x,ν~y)ν~x2+ν~y2+f2/v2γ2(55)E_{x,y}(\mathbf{r},f)=i\frac{e}{2\pi\epsilon_{0}v}\exp(i2\pi fz/v)\iint d\tilde{\nu}_{x}d\tilde{\nu}_{y}\exp[i2\pi(\tilde{\nu}_{x}x+\tilde{\nu}_{y}y)]\frac{(\tilde{\nu}_{x},\tilde{\nu}_{y})}{\tilde{\nu}_{x}^{2}+\tilde{\nu}_{y}^{2}+f^{2}/v^{2}\gamma^{2}} \tag*{(55)}
E_{x,y}(\mathbf{r},f)=-\frac{ef/\gamma v}{\epsilon_{0}v}\exp(i2\pi fz/v)\frac{(x,y)}{\sqrt{x^{2}+y^{2}}}K_{1}\left(\frac{2\pi f}{\gamma v}\sqrt{x^{2}+y^{2}\right)} \tag*{(56)}
Ex,y(r,ω)=ie(2π)2ϵ0vexp⁡(iωz/v)∬dkxdkyexp⁡[i(kxx+kyy)](kx,ky)kx2+ky2+α2(57)E_{x,y}(\mathbf{r},\omega)=i\frac{e}{(2\pi)^{2}\epsilon_{0}v}\exp(i\omega z/v)\iint dk_{x}dk_{y}\exp[i(k_{x}x+k_{y}y)]\frac{(k_{x},k_{y})}{k_{x}^{2}+k_{y}^{2}+\alpha^{2}} \tag*{(57)}
E_{x,y}(\mathbf{r},\omega)=-\frac{e\alpha}{2\pi\epsilon_{0}v}\exp(i\omega z/v)\frac{(x,y)}{\sqrt{x^{2}+y^{2}}}K_{1}\left(\alpha\sqrt{x^{2}+y^{2}\right)} \tag*{(58)}

By calculating the integral in Eq. (55), the transverse field strength is expressed as Eq. (56), where K1K_{1} is a Bessel function of the second kind. By introducing a parameter α=ω/γv=2πf/γv\alpha=\omega/\gamma v=2\pi f/\gamma v, Eqs. (55) and (56) were changed to the form described by the angular frequency in Eqs. (57) and (58). Notably, the factor 2πϵ0veα\frac{2\pi\epsilon_{0}v}{e\alpha} in Eq. (58) differs from (2π)3/2ϵ0veα\frac{(2\pi)^{3/2}\epsilon_{0}v}{e\alpha} in [36, 50], where the unitary convention of Fourier transformation g(t)=1(2π)1/2∫g(ω)exp⁡(−iωt)dtg(t)=\frac{1}{(2\pi)^{1/2}}\int g(\omega)\exp(-i\omega t)dt was applied.

The derivation of Eq. (56) required the integrals [51] listed as follows:

∫−∞+∞xsin⁡axb2+x2dx=πe−ab(59)\int_{-\infty}^{+\infty}\frac{x\sin ax}{b^{2}+x^{2}}dx=\pi e^{-ab} \tag*{(59)}
∫0+∞e−ac2+x2cos⁡(bx)dx=aca2+b2K1(ca2+b2)(60)\int_{0}^{+\infty}e^{-a\sqrt{c^{2}+x^{2}}}\cos(bx)dx=\frac{ac}{\sqrt{a^{2}+b^{2}}}K_{1}\left(c\sqrt{a^{2}+b^{2}}\right) \tag*{(60)}

Imaging system with two OAPs

Herein, a simple explanation of the imaging system composed of two OAPs is presented. We observed that,

geometrically, such a system can be considered as a thin lens with additional phase delay. The phase-shift effect of the parabolic mirror is shown in Figure 21(a). The parabolic surface, plotted as a red curve, is defined by the function y2=4fpxy^{2}=4f_{p}x, where fpf_{p} is the parent focal length of the parabola. The light indicated by l1l_{1} was incident at the center of a 90∘90^\circ parabolic mirror. The sideline l2l_{2} has a transverse distance ρ\rho to l1l_{1}. The tangent of the parabola at point (fp,2fp)(f_{p},2f_{p}) has a slope of 1 and a relative angle of 45∘45^\circ on the xx-axis. Without a parabolic mirror, the light was reflected by a flat mirror, as illustrated by the blue line, and the overall optical paths were the same. The red curve indicates that l2l_{2} is incident at point (x1,2fp−ρ)(x_{1},2f_{p}-\rho), where x1=(2fp−ρ)2/4fpx_{1}=(2f_{p}-\rho)^{2}/4f_{p}. Thus, the introduced path difference is fp−x1−ρf_{p}-x_{1}-\rho, which is calculated as follows:

Explanation of the phase shift introduced by a parabolic mirror and the overall transmission process from the source to the detector in a 2-OAP imaging system

Figure 21. (a) Explanation of the phase shift introduced by a parabolic mirror. (b) The overall transmission process from the source to the detector in a 2-OAP imaging system.

ΔL(ρ)=−ρ24fp(61)\Delta L(\rho)=-\frac{\rho^{2}}{4f_{p}} \tag*{(61)}

For the 90∘90^\circ OAP, the effective focal length was fe=2fpf_{e}=2f_{p}. For the 2-OAP system shown in Figure 21(b), the overall transformation function is calculated as T(ρ)=exp⁡[ik(F1+L+F2)]exp⁡[ik(ΔL1(ρ)+ΔL2(ρ))]T(\rho)=\exp[ik(F_{1}+L+F_{2})]\exp[ik(\Delta L_{1}(\rho)+\Delta L_{2}(\rho))]. Neglecting the constant phase delay, the transformation can be written as

T(ρ)=exp⁡[−ikρ22(1F1+1F2)]=exp⁡[−ikρ221f](62)T(\rho)=\exp\left[-\frac{ik\rho^2}{2}\left(\frac{1}{F_1}+\frac{1}{F_2}\right)\right] =\exp\left[-\frac{ik\rho^2}{2}\frac{1}{f}\right] \tag*{(62)}

where 1/f=1/F1+1/F21/f=1/F_1+1/F_2 and ff is the effective focal length of the overall system. By placing the source at the focal point of the first OAP, this imaging system had an effective focal length of ff and a magnification of F2/F1F_2/F_1. This calculation was performed based on geometrical optics.

Derivation of the formula for TR imaging using Fraunhofer approximation

The derivation of an analytical formula in the frequency domain for OTR imaging has been reported in existing literature [34, 35]. Here, we listed the details used to confirm the factors in SI units. The imaging system comprised only one thin lens. The propagation of TR was separated into two sessions: (i) source to lens and (ii) lens to detector. Assuming a metal foil of infinite size and neglecting the spherical phase in both the source and detector planes, the overall diffractive propagation can be expressed as Eq. (63) using the Fraunhofer approximation.

ED(XD,YD)=exp⁡(ikF1)iλF1exp⁡(ikF2)iλF2∫Xl,min⁡Xl,max⁡dXl∫Yl,min⁡Yl,max⁡dYlexp⁡[−ikF2(XDXl+YDYl)]×exp⁡[−ik2F2(Xl2+Yl2)]exp⁡[−ik2F1(Xl2+Yl2)]exp⁡[ik2F2(Xl2+Yl2)]exp⁡[ik2F1(Xl2+Yl2)]×∫−∞+∞dXs∫−∞+∞dYsES(Xs,Ys)exp⁡[−ikF1(XsXl+YsYl)](63)\begin{aligned} E^D(X_D,Y_D)={}&\frac{\exp(ikF_1)}{i\lambda F_1}\frac{\exp(ikF_2)}{i\lambda F_2}\int_{X_{l,\min}}^{X_{l,\max}}dX_l\int_{Y_{l,\min}}^{Y_{l,\max}}dY_l\exp\left[-\frac{ik}{F_2}(X_DX_l+Y_DY_l)\right]\\ &\times\exp\left[-\frac{ik}{2F_2}(X_l^2+Y_l^2)\right]\exp\left[-\frac{ik}{2F_1}(X_l^2+Y_l^2)\right]\exp\left[\frac{ik}{2F_2}(X_l^2+Y_l^2)\right]\exp\left[\frac{ik}{2F_1}(X_l^2+Y_l^2)\right]\\ &\times\int_{-\infty}^{+\infty}dX_s\int_{-\infty}^{+\infty}dY_sE^S(X_s,Y_s)\exp\left[-\frac{ik}{F_1}(X_sX_l+Y_sY_l)\right] \tag*{(63)} \end{aligned}
ED(ρD,ϕD)=eα2πϵ0v1λ2M∫0θmθdθ∫02πdϕlexp⁡[−ikMρDθcos⁡(ϕD−ϕl)]×∫0+∞K1(αρs)ρsdρs∫02πdϕs(cos⁡ϕs,sin⁡ϕs)exp⁡[−ikρsθcos⁡(ϕs−ϕl)](64)\begin{aligned} E^D(\rho_D,\phi_D)={}&\frac{e^{\alpha}}{2\pi\epsilon_0v}\frac{1}{\lambda^2M}\int_0^{\theta_m}\theta d\theta\int_0^{2\pi}d\phi_l\exp\left[-\frac{ik}{M}\rho_D\theta\cos(\phi_D-\phi_l)\right]\\ &\times\int_0^{+\infty}K_1(\alpha\rho_s)\rho_s d\rho_s\int_0^{2\pi}d\phi_s(\cos\phi_s,\sin\phi_s)\exp\left[-ik\rho_s\theta\cos(\phi_s-\phi_l)\right] \tag*{(64)} \end{aligned}

This system exhibits cylindrical symmetry because the pupil defined by the OAP has a circular shape. We change the notations of the coordinates as: (Xs,Ys)=ρs(cos⁡ϕs,sin⁡ϕs)(X_s,Y_s)=\rho_s(\cos\phi_s,\sin\phi_s), (Xl,Yl)=ρl(cos⁡ϕl,sin⁡ϕl)(X_l,Y_l)=\rho_l(\cos\phi_l,\sin\phi_l), (XD,YD)=ρD(cos⁡ϕD,sin⁡ϕD)(X_D,Y_D)=\rho_D(\cos\phi_D,\sin\phi_D). The Eq. (58) is rewritten as ES(ρs)=−eα2πϵ0vexp⁡(iωz/v)K1(αρs)E^S(\rho_s)=-\frac{e\alpha}{2\pi\epsilon_0v}\exp(i\omega z/v)K_1(\alpha\rho_s). With θ=ρl/F1\theta=\rho_l/F_1 and M=F2/F1M=F_2/F_1, Eq. (63) can be simplified as Eq. (64) by omitting all longitudinal phase factors. θm=\theta_m=

Rl/F1R_l/F_1 denotes the acceptance angle of the first OAP. Using the integral ∫02πdβ1(cos⁡β1,sin⁡β1)exp⁡[−iAcos⁡(β1−β2)]=−2πi(cos⁡β2,sin⁡β2)J1(A)\int_{0}^{2\pi} \mathrm{d}\beta_1(\cos\beta_1,\sin\beta_1)\exp[-iA\cos(\beta_1-\beta_2)] = -2\pi i(\cos\beta_2,\sin\beta_2)J_1(A) and the definition of the normalized transverse distance in the image plane ζ=kρD/M\zeta= k\rho_D/M, Eq. (64) can be simplified as

ED(ρD,ϕD)=−ekαϵ0vλM(cos⁡ϕD,sin⁡ϕD)∫0θmθJ1(ζθ) dθ×∫0+∞ρsdρsJ1(kθρs)K1(αρs)(65)\mathbf{E}^{D}(\rho_D,\phi_D)=-\frac{e k\alpha}{\epsilon_0 v\lambda M}(\cos\phi_D,\sin\phi_D)\int_{0}^{\theta_m}\theta J_1(\zeta\theta)\,\mathrm{d}\theta \times\int_{0}^{+\infty}\rho_s\mathrm{d}\rho_s J_1(k\theta\rho_s)K_1(\alpha\rho_s) \tag*{(65)}

By using the integral ∫0+∞xJ1(ax)K1(bx)dx=a/(a2b+b3)\int_{0}^{+\infty}xJ_1(ax)K_1(bx)\mathrm{d}x = a/(a^2b+b^3) [51], we have

ED(ρD,ϕD)=−eϵ0(cos⁡ϕD,sin⁡ϕD)λMv∫0θmθ2θ2+(γβ)−2J1(ζθ) dθ(66)\mathbf{E}^{D}(\rho_D,\phi_D)=-\frac{e}{\epsilon_0}\frac{(\cos\phi_D,\sin\phi_D)}{\lambda Mv}\int_{0}^{\theta_m}\frac{\theta^2}{\theta^2+(\gamma\beta)^{-2}}J_1(\zeta\theta)\,\mathrm{d}\theta \tag*{(66)}

In most cases, β≃1\beta\simeq1. Equation (66) can be expressed in Cartesian coordinates as follows:

ED(XD,YD)=−eϵ01λMv(XD,YD)XD2+YD2∫0θmθ2θ2+γ−2J1(ζθ) dθ(67)\mathbf{E}^{D}(X_D,Y_D)=-\frac{e}{\epsilon_0}\frac{1}{\lambda Mv}\frac{(X_D,Y_D)}{\sqrt{X_D^2+Y_D^2}}\int_{0}^{\theta_m}\frac{\theta^2}{\theta^2+\gamma^{-2}}J_1(\zeta\theta)\,\mathrm{d}\theta \tag*{(67)}

References

  1. [1]T. Tajima and J. M. Dawson, Physical Review Letters 43, 267 (1979).
  2. [2]C. Geddes, C. Toth, J. Van Tilborg, E. Esarey, C. Schroeder, D. Bruhwiler, C. Nieder, J. Cary, and W. Leemans, Nature 431, 538 (2004).
  3. [3]J. Faure, Y. Glinec, A. Pukhov, S. Kiselev, S. Gordienko, E. Lefebvre, J.-P. Rousseau, F. Burgy, and V. Malka, Nature 431, 541 (2004).
  4. [4]S. P. Mangles, C. Murphy, Z. Najmudin, A. G. R. Thomas, J. Collier, A. E. Dangor, E. Divall, P. Foster, J. Gallacher, C. Hooker, et al., Nature 431, 535 (2004).
  5. [5]W. P. Leemans, B. Nagler, A. J. Gonsalves, C. Toth, K. Nakamura, C. G. Geddes, E. Esarey, C. Schroeder, and S. Hooker, Nature physics 2, 696 (2006).
  6. [6]W. Leemans, A. Gonsalves, H.-S. Mao, K. Nakamura, C. Benedetti, C. Schroeder, C. Tóth, J. Daniels, D. Mittelberger, S. Bulanov, et al., Physical review letters 113, 245002 (2014).
  7. [7]A. Gonsalves, K. Nakamura, J. Daniels, C. Benedetti, C. Pieronek, T. de Raadt, S. Steinke, J. Bin, S. Bulanov, J. van Tilborg, et al., Physical Review Letters 122, 084801 (2019).
  8. [8]X. Wang, R. Zgadzaj, N. Fazel, Z. Li, S. Yi, X. Zhang, W. Henderson, Y.-Y. Chang, R. Korzekwa, H.-E. Tsai, et al., Nature communications 4, 1988 (2013).
  9. [9]H. T. Kim, K. H. Pae, H. J. Cha, I. J. Kim, T. J. Yu, J. H. Sung, S. K. Lee, T. M. Jeong, and J. Lee, Physical review letters 111, 165002 (2013).
  10. [10]M. Mirzaie, S. Li, M. Zeng, N. Hafz, M. Chen, G. Li, Q. Zhu, H. Liao, T. Sokollik, F. Liu, et al., Scientific reports 5, 14659 (2015).
  11. [11]W. Wang, W. Li, J. Liu, Z. Zhang, R. Qi, C. Yu, J. Liu, M. Fang, Z. Qin, C. Wang, et al., Physical review letters 117, 124801 (2016).
  12. [12]W. Wang, K. Feng, L. Ke, C. Yu, Y. Xu, R. Qi, Y. Chen, Z. Qin, Z. Zhang, M. Fang, et al., Nature 595, 516 (2021).
  13. [13]F. Albert, A. Thomas, S. Mangles, S. Banerjee, S. Corde, A. Flacco, M. Litos, D. Neely, J. Vieira, Z. Najmudin, et al., Plasma Physics and Controlled Fusion 56, 084015 (2014).
  14. [14]K. Huang, Y. Li, D. Li, L. Chen, M. Tao, Y. Ma, J. Zhao, M. Li, M. Chen, M. Mirzaie, et al., Scientific reports 6, 27633 (2016).
  15. [15]W. Yan, C. Fröhling, G. Golovin, D. Haden, J. Luo, P. Zhang, B. Zhao, J. Zhang, C. Liu, M. Chen, et al., Nature Photonics 11, 514 (2017).
  16. [16]R. Nakajima, Nature physics 4, 92 (2008).
  17. [17]Z. Huang and K.-J. Kim, Phys. Rev. ST Accel. Beams 10, 034801 (2007).
  18. [18]J. Shan, A. S. Weling, E. Knoesel, L. Bartels, M. Bonn, A. Nahata, G. A. Reider, and T. F. Heinz, Optics letters 25, 426 (2000).
  19. [19]X. Yan, A. MacLeod, G. Gillespie, G. Knippels, D. Oetp, A. van der Meer, and W. Seidel, Physical Review Letters 85, 3404 (2000).
  20. [20]I. Wilke, A. M. MacLeod, W. A. Gillespie, G. Berden, G. Knippels, and A. Van Der Meer, Physical review letters 88, 124801 (2002).
  21. [21]G. Berden, S. P. Jamison, A. M. MacLeod, W. A. Gillespie, B. Redlich, and A. Van der Meer, Physical review letters 93, 114802 (2004).
  22. [22]G. Berden, W. A. Gillespie, S. P. Jamison, E.-A. Knabbe, A. M. MacLeod, A. Van Der Meer, P. J. Phillips, H. Schlarb, B. Schmidt, P. Schümser, et al., Physical review letters 99, 164801 (2007).
  23. [23]B. Steffen, V. Arsov, G. Berden, W. A. Gillespie, S. Jamison, A. M. MacLeod, A. Van Der Meer, P. Phillips, H. Schlarb, B. Schmidt, et al., Physical Review Special Topics-Accelerators and Beams 12, 032802 (2009).
  24. [24]A. Lu. Cavalieri, D. Fritz, S. Lee, P. Bucksbaum, D. Reis, J. Rudati, D. Mills, P. Fuoss, G. Stephenson, C. Kao, et al., Physical review letters 94, 114801 (2005).
  25. [25]X. Yang, T. Tsang, T. Rao, J. Murphy, Y. Shen, and X. Wang, Applied Physics Letters 95, 231106 (2009).
  26. [26]W. Wang, Y. Du, L. Yan, Z. Chi, Z. Zhang, J. Hua, W. Huang, C. Tang, and M. Li, Physical Review Accel- erators and Beams 20, 112801 (2017).
  27. [27]C. Scoby, P. Musumeci, J. Moody, and M. Gutierrez, Physical Review Special Topics-Accelerators and Beams 13, 022801 (2010).
  28. [28]S. Jamison, G. Berden, A. M. MacLeod, D. Jaroszynski, B. Redlich, A. Van der Meer, and W. A. Gillespie, Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment 557, 305 (2006).
  29. [29]B. R. Steffen, Electro-optic methods for longitudinal bunch diagnostics at FLASH, Tech. Rep. (2007).DOI
  30. [30]S. Casalbuoni, H. Schlarb, B. Schmidt, P. Schmöser, B. Steffen, and A. Winter, Physical Review Special Topics-Accelerators and Beams 11, 072802 (2008).
  31. [31]J. van Tilborg, C. B. Schroeder, C. V. Filip, C. Tóth, C. G. R. Geddes, G. Fubiani, R. Huber, R. A. Kaindl, E. Esarey, and W. P. Leemans, Phys. Rev. Lett. 96, 014801 (2006).
  32. [32]A. D. Debus, M. Bussmann, U. Schramm, R. Sauerbrey, C. D. Murphy, Z. Major, R. Hörlein, L. Veisz, K. Schmid, J. Schreiber, K. Witte, S. P. Jamison, J. G. Gallacher, D. A. Jaroszynski, M. C. Kaluza, B. Hidding, S. Kiselev, R. Heathcote, P. S. Foster, D. Neely, E. J. Divall, C. J. Hooker, J. M. Smith, K. Ertel, A. J. Langley, P. Norreys, J. L. Collier, and S. Karsch, Phys. Rev. 104, 084802 (2010).
  33. [33]Q. Tian, Y. Du, H. Xu, Y. Liang, Y. Wang, Y. Tan, L. Yan, R. Li, C. Cheng, W. Huang, and C. Tang, Phys. Rev. Accel. Beams 23, 102802 (2020).
  34. [34]D. Xiang and W.-H. Huang, Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment 570, 357 (2007).
  35. [35]M. Castellano and V. A. Verzilov, Phys. Rev. ST Accel. Beams 1, 062801 (1998).
  36. [36]S. Casalbuoni, B. Schmidt, P. Schmöser, V. Arsov, and S. Wesch, Physical Review Special Topics-Accelerators and Beams 12, 030705 (2009).
  37. [37]H. Loos, R. Akre, A. Brachmann, F. Decker, Y. Ding, D. Dowell, P. Emma, J. Frisch, S. Gilevich, G. Hays, et al., in Proceedings of the 2008 Free-Electron Laser Conference (Gyeongju, Korea) (2008).
  38. [38]A. Potylitsyn, L. Sukhikh, T. Gutsvitskii, G. Kube, and A. Novokshonov, Physical Review Accelerators and Beams 23, 042804 (2020).
  39. [39]J. Goodman, Introduction to fourier optics, classic textbook reissue (1988).
  40. [40]C. B. Schroeder, E. Esarey, J. van Tilborg, and W. P. Leemans, Phys. Rev. E 69, 016501 (2004).
  41. [41]A. H. Lumpkin, M. Laberge, D. W. Rule, R. Zgadzaj, A. Hannasch, O. Zarini, B. Bowers, A. Irman, J. P. Couperus Cabadağ, A. Debus, A. Köhler, U. Schramm, and M. C. Downer, Phys. Rev. Lett. 125, 014801 (2020).
  42. [42]B. Schmidt, N. M. Lockmann, P. Schmöser, and S. Wesch, Phys. Rev. Accel. Beams 23, 062801 (2020).
  43. [43]K. Huang, H. Kotaki, M. Mori, T. Esirkepov, J. K. Koga, Y. Hayashi, N. Nakanıi, S. V. Bulanov, and M. Kando, Phys. Rev. Accel. Beams 22, 121301 (2019).
  44. [44]J. Beringer, J. F. Arguin, R. M. Barnett, K. Copic, O. Dahl, D. E. Groom, C. J. Lin, J. Lys, H. Murayama, C. G. Wohl, W. M. Yao, P. A. Zyla, C. Amsler, M. Antonelli, D. M. Asner, H. Baer, H. R. Band, T. Basaglia, C. W. Bauer, J. J. Beatty, V. I. Belousov, E. Bergren, G. Bernardi, W. Bertl, S. Bethke, H. Bichsel, O. Biebel, E. Blucher, S. Blusk, G. Brooijmans, O. Buchmueller, R. N. Cahn, M. Carena, A. Ceccucci, D. Chakraborty, M. C. Chen, R. S. Chivukula, G. Cowan, G. D’Ambrosio, T. Damour, D. de Florian, A. de Gouvêa, T. DeGrand, P. de Jong, G. Dissertori, B. Dobrescu, M. Doser, M. Drees, D. A. Edwards, S. Eidelman, J. Erler, V. V. Ezhela, W. Fetscher, B. D. Fields, B. Foster, T. K. Gaisser, L. Garren, H. J. Gerber, G. Gerbier, T. Gherghetta, S. Golwala, M. Goodman, C. Grab, A. V. Gritsan, J. F. Grivaz, M. Grünewald, A. Gurtu, T. Gutsche, H. E. Haber, K. Hagіwara, C. Hagmann, C. Hanhart, S. Hashimoto, K. G. Hayes, M. Heffner, B. Heltsley, J. J. Hernández-Rey, K. Hikasa, A. Höcker, J. Holder, A. Holtkamp, J. Huston, J. D. Jackson, K. F. Johnson, T. Junk, D. Karlen, D. Kirkby, S. R. Klein, E. Klempt, R. V. Kowalewski, F. Krauss, M. Kreps, B. Krusche, Y. Kuanyinov, Y. Kwon, O. Lahav, J. Laiho, P. Langacker, A. Liddle, Z. Ligeti, T. M. Liss, L. Littenberg, K. S. Lugovsky, S. B. Lugovsky, T. Mannel, A. V. Manohar, W. J. Marciano, A. D. Martin, A. Masoni, J. Matthews, D. Milstead, R. Miquel, K. Mönig, F. Moortgat, K. Nakamura, M. Narain, P. Nason, S. Navas, M. Neubert, C. Nevsky, Y. Nir, K. A. Olive, L. Page, J. Parsons, C. Patrignani, J. A. Peacock, S. T. Petcov, A. Piepke, A. Pomarol, G. Punzi, A. Quadt, S. Raby, G. Raffelt, B. N. Ratcliff, P. Richardson, S. R. Roesler, S. Rolli, A. Romaniouk, L. J. Rosenberg, J. L. Rosner, C. T. Sachrajda, Y. Sakai, G. P. Salam, S. Sarkar, F. Sauli, O. Schneider, K. Scholberg, D. Scott, W. G. Seligman, M. H. Shaevitz, S. R. Sharpe, M. Silari, T. Sjöstrand, P. Skands, J. G. Smith, G. F. Smoot, S. Spanier, H. Spieler, A. Stahl, T. Stanev, S. L. Stone, T. Sumiyoshi, M. J. Syphers, F. Takahashi, M. Tanabashi, J. Termini, M. Titov, N. P. Tkachenko, N. A. Törnqvist, D. Tovey, G. Valencia, K. van Bibber, G. Venanzoni, M. G. Vincter, P. Vogel, A. Vogt, W. Walkowiak, C. W. Walter, D. R. Ward, T. Watari, G. Weiglein, E. J. Weinberg, L. R. Wiencke, L. Wolfenstein, J. Womersley, C. L. Woody, R. L. Workman, A. Yamamoto, G. P. Zeller, O. V. Zenin, J. Zhang, R. Y. Zhu, G. Harper, V. S. Lugovsky, and P. Schaffner (Particle Data Group), Phys. Rev. D 86, 010001 (2012).
  45. [45]https://pdg.lbl.gov/2009/atomicnuclearproperties/.
  46. [46]https://en.wikipedia.org/wiki/SAE_304_stainless_steel/.
  47. [47]J. D. Jackson, Classical electrodynamics (1999).
  48. [48]G. Kube, TESLA-FEL Report 1, 2008 (2008).
  49. [49]M. L. Ter-Mikaelian, High-energy electromagnetic processes in condensed media, 29 (John Wiley & Sons, 1972).DOI
  50. [50]C. A. Brau, Modern problems in classical electrodynamics (Oxford univ. press, 2004).
  51. [51]I. S. Gradshteyn and I. M. Ryzhik, Table of integrals, series, and products (Academic press, 2014).

Paper details

vlnc:W_rfuyfy27
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents