WorksPhysics and Astronomy
Electrically-pumped high-power laser transmitter integrated on thin-film lithium niobate
Abstract
Integrated thin-film lithium niobate (TFLN) photonics has emerged as a promising platform for realization of high-performance chip-scale optical systems. Of particular importance are TFLN electro-optic modulators featuring high-linearity, low driving voltage and lowpropagation loss. However, fully integrated system requires integration of high power, low noise, and narrow linewidth lasers on TFLN chip. Here we achieve this goal, and demonstrate integrated high-power lasers on TFLN platform with up to 60 mW of optical power in the waveguides. We use this platform to realize a highpower transmitter consisting an electrically-pumped laser integrated with a 50 GHz modulator.
are first defined using a negative-tone electron-beam resist (FOx-16, Dow Corning). The pattern is then transferred to TFLN by reactive ion etching using Ar to reach the slab height of 300-nm. We later deposit 800-nm of SiO using plasma enhanced chemical vapor deposition as a device cladding. At the coupling region, the waveguides are tapered out to 8.2 m in width. This horn coupler geometry ensures maximal overlap with the optical mode produced by the 5-m wide DFB laser, and features high tolerances to lateral misalignment, mode height misalignment and separation (gap) between DFB and TFLN waveguides (Figure 1c).

Figure 1. Integration of Distributed Feedback Lasers (DFB) onto Thin-Film Lithium Niobate (TFLN): (a) An illustration of the proposed approach, along with mode profiles of TFLN coupler and laser. DFB laser is flipped and the height is adjusted to ensure matched mode-heights between the two waveguides (b). Optical mode profiles for both TFLN and DFB waveguides, obtained using a finite difference eigenmode solver. (c) Mode overlap simulations showing the coupling loss between the laser and TFLN waveguides as a function of the gap size (red) and height offset (blue). The latter are shown for gap size = 1.2μm (solid blue) and gap size = 0 μm (dashed blue). Inset shows the reference geometry for the gap and mode height offset calculation.
The final step in TFLN chip fabrication is realization of a trench at the end of the horn coupler, where DFB lasers will be introduced. First, the upper SiO cladding is etched using RIE with a mixture of CF and Ar gases. The LN layer is subsequently etched away using the same recipe as the waveguides, followed by a buried oxide etch (Figure 2(a-Figure 2c)). Since the sidewall angle sets the minimum coupling gap between the DFB and TFLN waveguides, a smaller sidewall angle is desired to increase the coupling efficiency (Figure 2(d-Figure 2e)). We evaluate the sidewall angle to be 85, which sets the minimum achievable gap between the laser and the waveguide to be 500 nm. Finally, a Ti/Pt/Au metal layer is deposited at the bottom of the trench using electron beam evaporation. This metallic layer serves as both one of the laser electrodes and the bonding pads. The laser is flip-chip bonded, P-side down, onto the metal layer at the bottom of the trench using gold-gold thermo-compression bonding (Figure 2f). The mode height offset between the DFB and TFLN waveguides can be controlled by adjusting the thickness of the gold layer deposited in the trench.

Figure 2. Fabrication steps of the flip-chip bonding process (a) Top-down and cross-section illustraton of the initial TFLN stack. (b) A trench is patterned and etched at the tip of the horn coupler. Then, a Ti/Pt/Au bonding pad (used for bonding and carrier injection) is defined 10-m away from the edge of the groove using a second lithography step. (c) the DFB laser is flipped and bonded to the pad using thermo-compression Au-Au bonding (Fineplacer Femto 2). (d) Scanning electron microscope (SEM) image of the LN waveguide facets after trench fabrication. (e) A close-up SEM of the TFLN horn-coupler facet prior to bonding. (f) SEM image of the DFB laser bonded to TFLN platform. Inset shows the laser facet prior to bonding. Scale bars represent 1 m.
the laser and the waveguide to be 500 nm. Finally, a Ti/Pt/Au metal layer is deposited at the bottom of the trench using electron beam evaporation. This metallic layer serves as both one of the laser electrodes and the bonding pads. The laser is flip-chip bonded, P-side down, onto the metal layer at the bottom of the trench using gold-gold thermo-compression bonding (Figure 2f). The mode height offset between the DFB and TFLN waveguides can be controlled by adjusting the thickness of the gold layer deposited in the trench.
On this passive device (Figure 3a), the LIV measurements are performed by contacting a sourcemeter (Keithley 2400) to the N- and P-side of the laser and increasing the current up to 1.0 A (Figure 3b). Clear evidence of single mode operation without mode hopping is observed for all integrated lasers tested (Figure 3b - inset). The laser emission is collected from the TFLN device facet using a single lens with numerical aperture of 0.4. Taking into account the out-coupling losses, which we measure to be 4.8 0.5 dB, we estimate an on-chip optical power in the range 60 7 mW at 1.0 A, and under room temperature operation (no cooling). Such on-chip power is among the highest reported for all integrated photonics platforms [7, 8, 9]. We achieve a coupling loss of 5 dB between the laser and TFLN waveguide which is due to sidewall slope, and alignment accuracy. Finally, the DFB linewidth is measured using a delayed self-heterodyne technique and found to be below 1 MHz. This is consistent with the linewidths measured on DFB lasers before integration.

Figure 3. Characterization of DFB laser integrated on passive TFLN device (a) Microscope image of an exemplary passive device with bonded DFB laser. TFLN chip features several waveguides coupled to ring resonators. In this work, DFB emission wavelength is not in resonance with the rings.(b) Optical power inside TFLN waveguide and laser voltage as a function of the laser driving current. The inset shows the lasing spectrum confirming single mode operation. The emission wavelength of DFB is not in resonance with the ring resonator in this experiment.
To illustrate the full potential of our approach, DFB lasers are integrated with a TFLN EO-modulator (Figure 4a). In this active device, a maximum of 25 mW (driving current 0.8 A) of optical power is estimated after the Mach-Zehnder interferometer (Figure 4b). The lower power in this active devices, compared to passive one, can be attributed to sub-optimal alignment as well as to absorption loss introduced by metal electrodes in this modulator design that features small electrode gap (electrode gaps ). The latter can be easily addressed by increasing the electrode separation, at the expense of reduced electro-optic efficiency.

Figure 4. Electrically-pumped Integrated Laser-Modulator Transmitter: (a) Optical image of the transmitter, consisting of a DFB laser and EO intensity modulators. (b) Power in TFLN waveguide versus laser current for the device pictured in 2a. (c) Normalized optical transmission vs. the voltage applied to the modulator. Red line corresponds to fit, with V. (d) Small-signal electro-optic response of a device with an active modulation length of 5-mm and a 3-dB bandwidth of GHz. , transmission coefficient of the scattering matrix.
Electro-optic modulation is achieved using an integrated intensity modulator with 5-mm long segmented travelling wave electrodes [10]. The electrodes are contacted using ground-signal-ground probes (GSG) (GGB Model 50A) and terminated using a termination. A measured of 4.3 V demonstrates that the DFB emission can be modulated efficiently on-chip (Figure 4c). To show the full-functionality of our platform as an integrated transmitter, we measure the high-frequency electro-optic response of our transmitter () using a 50 GHz Vector Network Analyzer (VNA, Agilent), 45 GHz fast photo-diode (New Focus 1014), and a pair of
50 GHz GSG probes (Figure 4d). RF cable losses, probes and detector response are subtracted from the measured frequency response. The response fluctuation beyond 45 GHz is due to the limited bandwidth of the photodiode.
In conclusion, we demonstrated the first high-power hybrid integrated transmitter on TFLN by flip-chip bonding a DFB laser. The bonding design allows efficient thermal anchoring for the laser which allowed uncooled operation with up to 60 (25) mW in the passive (active) waveguides. Our high-power transmitter platform will enable a new class of applications in digital and analog communication spaces. Beyond communication systems, integrating high-power lasers on other TFLN devices such as EO [11] and Kerr combs [12, 13] enables a critical step towards realizing fully-integrated spectrometers [14]. Additionally, other exciting frontiers include optical remote sensing and beam forming [15], photon pair generation [16], and efficient frequency conversion [13, 17] for realization of quantum networks. Future work would focus on realization of fully-integrated photonic links through integrating high-power and high-bandwidth photo-detector on TFLN platform [18]. Recently, a complementary approach to TFLN-laser integration has been reported [19].
Funding: Defense Advanced Research Projects Agency (DARPA) (HR0011-20-C-0137). Air Force Office of Scientific Research (AFOSR) (FA9550-19-1-0376)
Acknowledgement: We acknowledge assistance from Mehdi Rezaee, Tomas Stupnis, Dmitry Padubny and Neil Sinclair. Device fabrication was performed at the Center for Nanoscale Systems (CNS) at Harvard University.
Disclosures: L.H, M.Z, and M.L are involved in developing lithium niobate technologies at HyperLight Corporation.. H.G, and L.J are involved in developing DFB lasers at Freedom Photonics.
Disclaimer: The views, opinions and/or findings expressed are those of the author and should not be interpreted as representing the official views or policies of the Department of Defense or the U.S. Government.
References
References
- [7]M. Theurer, M. Moehrle, A. Sigmund, K.-O. Velthaus, R. Oldenbeuving, L. Wevers, F. Postma, R. Mateman, F. Schreuder, D. Geskus, et al., “Flip-chip integration of inp and sin,” IEEE Photonics Technology Letters, vol. 31, no. 3, pp. 273–276, 2019.DOI
- [8]D. Huang, M. A. Tran, J. Guo, J. Peters, T. Komljenovic, A. Malik, P. A. Morton, and J. E. Bowers, “High-power sub-khz linewidth lasers fully integrated on silicon,” Optica, vol. 6, no. 6, pp. 745–752, 2019.DOI
- [9]D. Kharas, J. J. Plant, W. Loh, R. B. Swint, S. Bramhavar, C. Heidelberg, S. Yegnanarayanan, and P. W. Juodawlkis, “High-power ( gt;300 mw) on-chip laser with passively aligned silicon-nitride waveguide dbr cavity,” IEEE Photonics Journal, vol. 12, no. 6, pp. 1–12, 2020.DOI
- [10]P. Kharel, C. Reimer, K. Luke, L. He, and M. Zhang, “Breaking voltage-bandwidth limits in integrated lithium niobate modulators using micro-structured electrodes,” Optica, vol. 8, no. 3, pp. 357–363, 2021.
- [11]M. Zhang, B. Buscaino, C. Wang, A. Shams-Ansari, C. Reimer, R. Zhu, J. M. Kahn, and M. Lončar, “Broadband electro-optic frequency comb generation in a lithium niobate microring resonator,” Nature, vol. 568, no. 7752, pp. 373–377, 2019.DOI
- [12]Y. He, Q.-F. Yang, J. Ling, R. Luo, H. Liang, M. Li, B. Shen, H. Wang, K. Vahala, and Q. Lin, “Self-starting bi-chromatic linbo 3 soliton microcomb,” Optica, vol. 6, no. 9, pp. 1138–1144, 2019.DOI
- [13]C. Wang, C. L. Langrock, A. Marandi, M. Jankowski, M. Zhang, B. Desiatov, M. M. Fejer, and M. Lončar, “Ultrahigh-efficiency wavelength conversion in nanophotonic, periodically poled lithium niobate waveguides,” Optica, vol. 5, pp. 1438–1441, Nov 2018.DOI
- [14]A. Shams-Ansari, M. Yu, Z. Chen, C. Reimer, M. Zhang, N. Picqué, and M. Lončar, “An integrated lithium-niobate electro-optic platform for spectrally tailored dual-comb spectroscopy,” arXiv preprint arXiv:2003.04533, 2020.
- [15]P. A. Morton and M. J. Morton, “High-power, ultra-low noise hybrid lasers for microwave photonics and optical sensing,” J. Lightwave Technol., vol. 36, pp. 5048–5057, Nov 2018.
- [16]J. Zhao, C. Ma, M. Rüsing, and S. Mukherjea, “High quality entangled photon pair generation in periodically poled thin-film lithium niobate waveguides,” Physical review letters, vol. 124, no. 16, p. 163603, 2020.DOI
- [17]J. Lu, M. Li, C.-L. Zou, A. Al Sayem, and H. X. Tang, “Toward 1% single-photon anharmonicity with periodically poled lithium niobate microring resonators,” Optica, vol. 7, no. 12, pp. 1654–1659, 2020.DOI
- [18]Y. Wang, Z. Wang, Q. Yu, X. Xie, T. Posavitz, M. Jacob-Mitos, A. Ramaswamy, E. J. Norberg, G. A. Fish, and A. Beling, “High-power photodiodes with 65 ghz bandwidth heterogeneously integrated onto silicon-on-insulator nano-waveguides,” IEEE Journal of Selected Topics in Quantum Electronics, vol. 24, no. 2, pp. 1–6, 2018.DOI
- [19]C. O. de Beeck, F. M. Mayor, S. Cuyvers, S. Poelman, J. F. Herrmann, O. Atalar, T. P. McKenna, B. Haq, W. Jiang, J. D. Witmer, G. Roelkens, A. H. Safavi-Naeini, R. V. Laer, and B. Kuvken, “Ti/V-on-lithium niobate amplifiers and lasers,” Optica, vol. 8, pp. 1288–1289, Oct 2021.