betaFeedback

WorksPhysics and Astronomy

Dynamics of jet breakup and the resultant drop size distribution: effect of nozzle size and impingement velocity

Abstract

We conduct systematic experiments to investigate the dynamics of liquid jet breakup and the resulting droplet size distribution, emphasizing the influence of liquid jet velocity and needle exit diameter. We precisely control jet formation using a pressurized water tank equipped with needles of different sizes. Our study quantifies breakup dynamics through dimensionless parameters such as the liquid Weber number and the needle exit area ratio. Our key findings identify three distinct breakup regimes, such as dripping, Rayleigh, and wind-induced, each dictated by the interplay of surface tension and aerodynamic forces for various combinations of liquid jet velocity and needle exit diameter. We construct a regime map to delineate different breakup behaviours in the We - Ar space. It is observed that lower jet velocities produce narrow probability density functions for jet breakup length due to stable jets, whereas higher velocities result in broader distributions. Increasing jet velocity extends breakup lengths for moderate flow rates due to enhanced stability in the Rayleigh regime, but higher velocities induce instability, leading to shorter breakup lengths. Additionally, we analyze the effects of the needle exit area ratio and liquid Weber number on droplet size distribution, highlighting the transition from mono-modal to bi-modal distribution under varying conditions.

Introduction

Breakup of liquid jets and droplets is relevant in numerous practical applications, including combustion[1], spray coating[2], pharmaceuticals industries[3, 4], and printing technologies[5, 6] to name a few. It also plays a vital role in natural phenomena, such as rainfall[7, 8, 9, 10]. In these applications, liquid jet atomization is essential, with the primary and secondary breakup of the fluid jet playing a crucial role in determining the efficiency and effectiveness of the atomization process.

In the initial stage of the breakup of a liquid jet, known as primary atomization, a ligament forms and fragments into primary droplets. This stage is followed by secondary atomization, during which these primary droplets further disintegrate into smaller satellite droplets due to aerodynamic forces overcoming viscous and surface tension forces[11, 12, 13]. Different breakup regimes are characterized primarily based on the Weber number (WeWe), which represents the ratio of inertial to surface tension forces. It is defined as We=ρU2D/σWe = \rho U^2D/\sigma, ρ\rho denotes the density of the liquid, UU represents the jet velocity, DD is the needle diameter and σ\sigma denotes the interfacial tension of the liquid. The Weber number helps determine whether kinetic or surface tension energy is dominant in the breakup process[11, 14, 15]. Various breakup regimes have been identified based on the Weber number, including the Rayleigh regime, the first wind-induced regime, the second wind-induced regime, and the atomization regime[11, 14, 16, 17].

Previous studies have explored several aspects of liquid jet breakup. Borthakur et al. [18] numerically investigated the formation and breakup of a liquid jet emerging from an orifice, assessing its behaviour under both gravitational and non-gravitational conditions. They found that the jet breakup length (length between the needle tip and the location where the jet breakup occurs) increases with increasing Weber and Ohnesorge numbers. The Ohnesorge number is the ratio of viscous forces to inertial and surface tension forces, given by Oh=μ/ρσDOh = \mu/\sqrt{\rho\sigma D}. Here, μ\mu represents the liquid viscosity. Birouk and Lekic [19] reviewed the disintegration of liquid jets from convergent nozzles, highlighting the effect of various factors, such as internal flow and nozzle geometry, which had been neglected in earlier research. Wu et al. [4] examined the impact of bubbles on the breakup of liquid jets, revealing that bubbles significantly reduce the breakup length, thereby enhancing atomization performance. They also noted that the type of gas influences the process, with lighter gases causing a more substantial decrease in breakup length due to fluid momentum conservation. Grant and Middleman [20] highlighted the limitations in understanding jet disintegration, noting that existing theories were restricted to low-speed laminar jets in still air. They emphasized the influence of the ambient medium, turbulence, and velocity profile on the jet dynamics. Srinivasan and Sinha [21] also investigated the influence of velocity profile on jet breakup phenomenon. Mousavi, Siavashi, and Bagheri [3] investigated the impact of non-Newtonian rheology, specifically shear-thinning behaviour, on jet breakup and droplet production across various regimes. They found that viscosity and rheology significantly influence breakup length and transition in the jetting regime. Tanase, Rasuceanu, and Balan [22] examined the initial stages of liquid injection through a capillary nozzle, focusing on the asymmetry of the water-air interface before jet formation. They characterized flow dynamics during drop formation and pinch-off driven by surface tension effects.

Several researchers have also investigated the effect of orifice geometry and injection pressure on liquid jet behaviour. Kiaoulis et al. [23] assessed the influence of inlet geometry on pressure drop and jet breakup length in single circular orifices in rocket engine injectors. They found that sharp-edge inlets exhibited more significant pressure drop and longer breakup lengths at small orifices, while chamfered inlets showed longer breakup lengths at larger orifice sizes. Sharma and Fang [24], Wang and Fang [25] found that non-circular orifice geometries, such as rectangular, square, and triangular shapes, induce greater instability and faster breakup of low-pressure liquid jets compared to circular orifices of similar cross-sectional areas, highlighting their potential for enhancing fuel atomization and fluid dynamics economically. Borthakur, Biswas, and Bandyopadhyay [26] investigated liquid drop and jet dynamics during injection through an orifice, examining the interplay of inertia and viscosity. They identified self-similar behaviours in drop growth and the transition from periodic dripping to elongated jetting. Rajesh, Sakthikumar, and Sivakumar [27] presented findings on spray formation from non-circular orifices, revealing superior spray characteristics for elliptical orifices. Geng et al. [28] investigated the impact of injection pressure and orifice diameter on soybean biodiesel spray characteristics. They found that higher injection pressures and smaller orifice diameters enhanced atomization. Rajesh et al. [29] explored the spray characteristics of kerosene jets from non-circular (elliptic, triangular, square) and circular orifices. Their observations reveal that non-circular orifices exhibited coarsening of atomization, as indicated by an increase in Sauter mean diameter (SMD) across all tested velocities. This was attributed to filament and core breakup, which generated larger liquid structures like filaments and ligaments, particularly noticeable in non-circular orifices. The study also revealed bi-modal drop size distributions at lower velocities, transitioning to mono-modal distributions at higher velocities, with filament breakup resulting in smaller drop sizes in triangular orifices than circular orifices.

Few studies have explored the dynamics and instability characteristics of rectangular and elliptical liquid jets. Tadjfar and Jaberi [30] conducted a comprehensive review of the literature on rectangular liquid jets, incorporating Rayleigh’s model with different aspect ratios and shape type functions. Morad, Nasiri, and Amini [31] numerically investigated low-speed liquid jets from rectangular orifices transitioning into elliptical shapes, observing that axis-switching occurred solely in elliptical cross-sections. They found that higher aspect ratios correlate with shorter breakup lengths due to an increase in the dominant wave number. Jaberi and Tadjfar [32] studied axis-switching oscillations in rectangular and elliptical liquid jets with different aspect ratios. Their model improved predictive accuracy by considering the effects of shape, aspect ratio, and Weber number, incorporating a logarithmic correction term. Kooij et al. [33] demonstrates that drop size in the breakup of liquid sheets is primarily determined by the interplay between fluid inertia and surface tension, allowing for predictions based on the Weber number and nozzle geometry. The resulting drop size distribution, described by a compound gamma distribution, varies with nozzle type, with conical nozzles producing more uniform ligaments and flat fan nozzles yielding a broader size range.

Table I provides an overview of previous studies on liquid jet breakup dynamics, categorizing them into experimental and numerical investigations that cover various nozzle geometries, including circular, rectangular, and elliptical shapes, as well as different nozzle diameters. It also highlights the range of Weber (WeWe) and Reynolds (ReRe) numbers considered in these studies.

ReferenceApproachJet’s liquidNozzle shapeNozzle diameter (mm)WeRe
Present studyExperimentalWaterCircular0.051 to 0.8380 to 6113.33.6 to 24586
Ref.3NumericalBloodCircular1, 1.6, 2.1592 to 66.45 to 178.87
Ref.15Numerical-Circular0.28350, 100-
Ref.22Experimental and numerical-Circular1.8101,170
Ref.4ExperimentalWaterCircular3--
Ref.28ExperimentalSoybean biodieselCircular0.366, 0.315, 0.260--
Ref.34,35ExperimentalWaterCircular0.6-1790 to 61000
Ref.36ExperimentalWaterCircular0.495, 0.7904.53 to 38.23-
Ref.37ExperimentalWater, glycerol, ethanolCircular1, 2, 4--
Ref.38NumericalWaterCircular, elliptical0.515 to 330837 to 3884
Ref.31NumericalWaterCircular, rectangle, square, elliptical0.3 (circular)4 to 80250 to 1000
Ref.24ExperimentalWaterCircular, rectangle, square, triangle0.31 (circular)0 to 25000-
Ref.25ExperimentalWaterCircular, rectangle, square, triangle0.31 (circular)0 to 20000 to 6500
Ref.29ExperimentalJet A-1Circular, square, triangle, elliptical1.06 (circular)14198 to 38445-
Ref.27ExperimentalWater, glycerol, jet A-1Square, triangle, elliptical4.82 to 4.97--
Ref.30ExperimentalWaterRectangle1.75 to 2.780 to 16000 to 25000
Ref.32ExperimentalWaterRectangle, elliptical1.75 to 2.593 to 1000300 to 20000

Table I. Summary of earlier studies including the present investigation on jet breakup dynamics.

However, despite these extensive efforts, a systematic examination of the effects of nozzle diameter and flow rate on different jet breakup dynamics remains unexplored. Our research aims to fill this gap by investigating jet breakup dynamics using circular orifices with eight distinct diameters. In addition to analyzing the breakup phenomenon, we examine the resulting droplet size distribution by varying the liquid jet velocity and needle exit diameter. The results from numerous experiments are presented using dimensionless numbers such as the Weber number (WeWe) and the exit area ratio of the nozzle (ArA_r).

As discussed above, despite numerous studies, gaps persist in our understanding of jet breakup dynamics. Additionally, only a limited number of researchers have systematically explored jet breakup phenomena. These factors motivated us to undertake a systematic experimental study involving variations in the flow rate of the liquid jet and the needle diameter. In the present study, we designed and conducted experiments to investigate the dynamics of liquid jet breakup and droplet size distribution by varying jet velocity and needle exit diameter. Our experimental setup included a pressurized water dispensing system and a high-speed camera, which captured the jet behaviour, facilitated by a shadowgraph imaging system for detailed analysis. Water served as the working fluid, and we achieved precise control over jet velocity by adjusting the air pressure supplied to the water tank. Needles of varying sizes were utilized to create different jet diameters, and we systematically recorded the jet breakup process at 5000 frames per second (fps). Our analysis involved calculating dimensionless parameters such as the liquid Weber number and needle exit area ratio to characterize the effects of jet velocity and needle diameter on jet breakup length and stability. A regime map was plotted to demarcate different breakup behaviours in the We−ArWe-A_r space.

The remainder of the manuscript is organized as follows: Section II provides a detailed description of the experimental methodology, covering setup details, varied parameters, data acquisition techniques, post-processing methods, and jet characterization. Section III discusses the results. Finally, concluding remarks are presented in Section IV.

Experimental setup and procedure

A schematic of the experimental setup used in this study is depicted in Figure 1a. It consists of a water dispensing system including an air compressor, a pressurized water tank, a ball valve, a pressure regulator, a dispensing needle, a water collector, and a shadowgraph image-capturing system which uses a high-speed camera, a diffuser sheet, and a light source. Water is used as the working fluid having density, ρ=997 kg/m3\rho= 997\ \mathrm{kg}/\mathrm{m}^{3}, viscosity, μ=0.001 Pa⋅s\mu= 0.001\ \mathrm{Pa}\cdot\mathrm{s}, and surface tension, σ=0.072 N/m\sigma= 0.072\ \mathrm{N}/\mathrm{m}.

Figure 1. (a) Schematic representation of the experimental setup. It consists of a water dispensing system and a shadowgraph image-capturing system. (b) A schematic depicting the needle and the jet breakup length. Here, LnL_n denotes the length of the needle, DD represents the diameter of the needle, UU is the jet velocity at the needle exit, and LL signifies the instantaneous jet breakup length. The top of the tank and the needle exit are at the same height marked by the horizontal dashed line.

The water tank, equipped with an inlet at the top and an outlet at the bottom, is initially filled with deionized (DI) water. An air compressor connected to the inlet supplies pressurized air to the tank, with an air dryer and moisture remover ensuring air quality in the compressed air line. The air pres-

sure within the tank is regulated by a pressure regulator positioned at the inlet line of the water tank. The bottom outlet is connected to a needle via a polyurethane pipe, enabling the dispensing of liquid. A ball valve installed at the outlet controls the liquid flow from the tank. The dispensed water is collected in a container positioned on the ground. To determine the volumetric flow rate of the water, we measure the liquid volume collected in a measuring cylinder and the corresponding time taken. These measurements are essential for calculating the average jet velocity to characterize the liquid jet. We employ a high-speed camera (model: Phantom VEO 640L; make: Vision Research, USA) with Nikkor lens AF Nikkor 135 mm f/2.0D to capture the videos of the liquid jet. The shadowgraph technique used in the present study employs diffused backlit illuminations (GSVITEC light source; model: MultiLED QT; make: GSVITEC, Germany) to illuminate the background for the camera. To ensure appropriate brightness, we utilize high-power (150 W and 12000 lm) light-emitting diode lights diffused by a diffuser sheet as the background light source.

In order to vary the jet diameter, eight needle sizes ranging from 34 gauge to 18 gauge were used. The velocity of the jets was controlled by adjusting the pressurized air supplied to the water tank, with the water tank pressure (PP) ranging from 10 to 120 psi. Each needle size is characterized by its exit area ratio (ArA_r), defined as Ar=(D/Ds)2A_r = (D/D_s)^2, where DD is the needle exit diameter and DsD_s is the exit diameter of the smallest needle (refer to Table II). The liquid Weber number, defined as We=ρU2D/σWe = \rho U^2D/\sigma, where ρ\rho is the density of water, UU is the jet velocity at the needle exit, DD is the needle exit diameter, and σ\sigma is the interfacial surface tension of water. In the present study, the dynamics of the jet is characterized by varying ArA_r and WeWe.

The experiment began by filling the water tank with deionized (DI) water until the water level aligned with the needle exit. The needle exit and the top of the water tank were positioned in a straight line. An air pipe from the compressor line was connected to the top of the water tank, and the desired pressure was set using a pressure regulator. The ball valve was fully opened to pressurize the water tank, causing the water jet to emerge from the needle into the quiescent air. After a stabilization period of 5 seconds, a high-speed camera was triggered to record the jet and its subsequent breakup. Due to the rapid dynamics involved, all experiments were recorded at 5000 frames per second (fps) with a resolution of 400 × 2560 pixels, covering an area of 20.38 mm × 130.41 mm. Each frame had an exposure time of 1 microsecond (μ\mus), and the spatial resolution was 19.63 pixels per millimetre (pix/mm). The recorded videos were saved to a local computer. A background video without the water jet was also recorded to assist with post-processing. The Phantom Camera Control (PCC) software was utilized to convert the videos into image sequences. These images were subsequently analyzed using Fiji ImageJ and MATLAB® software for further investigation and data extraction.

fig:1b depicts a schematic of the needle and the emerging liquid jet from the nozzle. The parameter LnL_n represents the length of the needle, which is maintained constant at 13 mm

for all needles used in this study. The parameter DD denotes the diameter of the needle, a variable parameter manipulated in this study and reflected in the needle exit area ratio (ArA_r). The parameter LL signifies the instantaneous breakup length of the liquid jet ejected from the needle, which varies over time. The jet breakup length was measured from the needle exit tip to the point where the jet breaks up into ligaments and droplets.

The various post-processing steps within the MATLAB® framework are demonstrated in Figure 2, involving five sequential steps. Initially, videos are captured using a Photron Camera Controller (PCC), from which individual frames are extracted. Figure 2(a) represents one such raw frame from the recorded video of the case Ar=66A_r = 66 and We=39.2We = 39.2. To enhance the image quality, multiple pre-captured Tag Image File Format (TIFF) background images are read and combined to create a single composite background image. This composite image is normalized to fit the standard 8-bit range, ensuring image consistency. The raw images are then processed by dividing them with the background image to eliminate background effects. Invalid pixel values are replaced with the average of valid pixels, and the mean grayscale values of the images are adjusted. The resulting processed images, demonstrating successful background removal, are saved without compression; Figure 2(b) shows one such processed frame. Subsequently, the background-normalized image is converted into a binary image (Figure 2(c)). This binarisation step involves thresholding, where pixel values are set to either black or white, simplifying the images to highlight essential features for further analysis. The final two steps include data collection. The binary images are processed further by reading each frame of a multi-TIFF file. For every image, we obtain the region properties data and specify that from the top region (which is the jet), we store the bounding box data and then calculate the breakup length of the jet from the yy-coordinates of the bounding box data. A line is drawn along the left edge of the background normalized image (shown in Figure 2(b)) to verify the jet length for every frame visually, and the processed images are saved as a new TIFF file shown in Figure 2(d). Finally, in Figure 2(e), we isolated the jet using the calculated jet length data and then filtered regions in the image based on area, circularity, and solidity criteria to extract the area equivalent diameters for each detected droplet. We validated the droplet detection by overlaying the edges on the original image, achieving highly accurate droplet identification due to the smooth and transparent background. This comprehensive MATLAB® processing workflow allows for accurately determining jet length and droplet size distribution, ensuring robust data analysis for our study.

Various post-processing steps for obtaining the jet length and droplet size distribution

Figure 2. Various post-processing steps in the MATLAB® framework to obtain the jet length and droplet size distribution. The typical case considered here is for Ar=66A_r = 66 and We=39.2We = 39.2. Here, (a) Raw image, (b) Image after background normalization, (c) Image after binarisation, (d) Jet length calculation, and (e) Jet removal and droplet size capturing.

TABLE II: The experimental parameters used in the present study. The columns include symbols, the needle gauge, needle diameter (DD), needle exit area ratio (ArA_r), and liquid Weber number (We=ρU2D/σWe = \rho U^2D/\sigma). The increasing sizes of circular symbols correspond to increasing needle exit diameters, a convention maintained consistently throughout the manuscript.

CaseNeedle size (gauge)DD (mm)ArA_rWeWe
1340.05110.002 - 0.288
2320.1084.50.06 - 4.08
3300.159100.6 - 21.2
4270.21171.4 - 35.0
5250.26266.1 - 141.9
6220.4136639.2 - 982.3
7200.603140280.3 - 3780.7
8180.838270398.3 - 6113.3

Table 2.

Jet characterisation

Figure 3 illustrates the variation in the liquid Weber number (We=ρU2D/σWe = \rho U^2D/\sigma) and Reynolds number (Re=UρD/μRe = U\rho D/\mu) as a function of the water tank pressure (PP) for various needle exit area ratios (ArA_r) considered in this study. Here, an increase in the size of the circular symbols corresponds to an increase in the needle size (or needle exit area ratio). The line with black squares shows the results of Wang and Fang [25] associated with a circular orifice. In our experiments, the water tank pressure (PP) ranged from 10 to 120 psi, with increments of 5 psi up to 50 psi and 10 psi beyond that. Since deionized (DI) water serves as the constant working fluid in all experiments, its properties, such as density, surface tension, and viscosity, remain unchanged. Therefore, variations in the Weber and Reynolds numbers are solely influenced by the velocity of the liquid jet and the diameter of the needle. For needles with specific exit area ratios, an increase in both the Weber and Reynolds numbers is observed with an increase in water tank pressure, as depicted in Figure 3a and Figure 3b, respectively. This increase correlates with Bernoulli’s principle, where higher water tank pressure enhances the liquid mass flow rate, thereby increasing the velocity of the liquid jet. Moreover, at a given water tank pressure, an increase in the Weber and Reynolds numbers is noted as the needle

Figure 3. Variation of (a) liquid Weber number (WeWe), and (b) Reynolds number (ReRe) with water tank pressure (PP) (in psi) for different needle exit area ratios (ArA_r). The increasing sizes of circular symbols correspond to increasing needle exit diameters. The line with black square symbols shows the results of Wang and Fang [25].

exit area ratio increases, attributable to the simultaneous rise in jet velocity and exit diameter. Since these needles function like capillary tubes with small diameters, increasing the needle exit diameter enhances the liquid mass flow rate and discharge coefficient, resulting in higher jet velocities. Consequently, higher water tank pressures lead to greater volumes of liquid dispensed from the needle over the same duration, further elevating both the Weber and Reynolds numbers.

The characteristics of the jet in our study are compared with findings from Wang and Fang [25], revealing a similar trend where both the Weber and Reynolds numbers increase with pressure, as depicted in Figure 3a and (Figure 3b). Wang and Fang [25] utilized a circular orifice with a thickness of 2 mm and a diameter of 0.31 mm, resulting in a needle exit area ratio (ArA_r) of 36, which aligns closely with the highest ArA_r used in our study. This similarity arises despite our longer needle length of 13 mm, as previous research indicates that the needle length relative to its diameter (Ln/DL_n/D) indirectly influences the longevity of the jet dynamics[19]. The Ln/DL_n/D ratio in Wang and Fang [25] aligns comparably well with our cases ranging from Ar=66A_r = 66 to 270, thus validating the relevance of their findings across these ArA_r ranges.

Figure 4 illustrates the temporal evolution of the normalized liquid jet breakup length. The data is presented for three cases characterized by different needle exit area ratios (ArA_r) and liquid Weber numbers (WeWe). These cases are represented in the figure by various line styles: the black dotted line (case 1: Ar=1A_r = 1 and We=0.05We = 0.05), the red dashed line (case 2: Ar=10A_r = 10 and We=2.6We = 2.6), and the blue dot-dash line (case 3: Ar=26A_r = 26 and We=13.5We = 13.5). Additionally, the figure includes solid straight lines representing the average jet breakup length for each case. For quantitative analysis, the liquid jet breakup length (Lj=L/DL_j = L/D) was normalized by the respective needle exit diameter, and the respective needle exit diameter and the jet exit velocity normalized the time (T=tU/DT = tU/D). We recorded a 300-frame video using a high-speed camera operating at 5000 frames per second (fps), resulting in a video duration of 60 milliseconds for each experiment.

The figure shows that both the needle exit area ratio and the liquid Weber number significantly influence the stability of jet breakup length. As the needle exit area ratio (ArA_r) increases, more pronounced oscillations in the jet breakup length are observed. Similarly, an increase in the liquid Weber number (WeWe) also results in more significant variations in the jet breakup length. This indicates a direct correlation between the complexity of the jet breakup process and the needle exit area ratio (ArA_r) and the Weber number (WeWe). The solid black, red, and blue lines in the figure represent the mean jet breakup lengths for the first, second, and third cases, with average normalized lengths of 45.3, 146.3, and 253.7, respectively, providing an apparent reference for the average behaviour over time. The oscillatory nature of the jet breakup length in each case can be attributed to the instabilities in the liquid jet, which are more pronounced at higher area ratios and liquid Weber numbers. Figure 4 highlights the intricate relationship between needle geometry and jet breakup behaviour. The results demonstrate that larger needle exit area ratios and higher liquid Weber numbers lead to increased jet breakup lengths and more significant variations over time. These findings provide valuable insights into the underlying mechanisms governing liquid jet breakup and are essential for optimizing needle design in various fluid dynamics applications.

Figure 4. Variation of normalised liquid jet breakup length, Lj=L/DL_j = L/D, with dimensionless time, T=tU/DT = tU/D, for three different cases. Here, LL represents the instantaneous jet breakup length, and tt denotes physical time in seconds. The black dotted line corresponds to Ar=1A_r = 1, We=0.05We = 0.05; the red dashed line is for Ar=10A_r = 10, We=2.6We = 2.6; and the blue dot-dash line corresponds to Ar=26A_r = 26, We=13.5We = 13.5. Solid straight lines indicate the mean value of jet breakup length for each case. All three cases exhibit characteristics of the Rayleigh breakup regime.

Results and discussion

Different breakup phenomena

The breakup of a liquid jet is influenced by the competition between inertial and aerodynamic forces, leading to distinct breakup regimes depending on jet velocity and liquid properties such as surface tension and viscosity[39, 40, 41, 42, 43]. As jet velocity increases, breakup transitions from dripping[3], through the Rayleigh regime[34], wind-induced regimes[36], and ultimately to atomization[34, 35, 44, 45]. Our study initially explores these observed breakup regimes, followed by an analysis of jet breakup length and droplet size distribution in subsequent subsections. Figure 5 illustrates these distinct liquid jet breakup regimes, namely dripping, Rayleigh, and wind-induced, corresponding to different needle exit area ratios and liquid Weber numbers, reflecting the breakup behaviours observed under varied flow conditions. In Figure 5, a 5 mm scale bar is provided for reference, offering context for the images presented.

Figure 5. Demonstration of various liquid jet breakup regimes, namely dripping, Rayleigh, and wind-induced regimes, observed for different needle exit area ratios and liquid Weber numbers. A scale bar of 5 mm length is included for reference.

In the dripping regime[37, 46, 47], observed at the lowest flow velocities, individual droplets form and dispense one by one from the needle tip without forming a continuous jet. This regime occurs when the liquid Weber number (WeWe) is very low, indicating that surface tension dominates over inertial forces. As a result, the liquid does not have sufficient velocity to form a coherent jet, forming discrete droplets due to gravitational and surface tension effects.

The Rayleigh regime[34, 48, 49] is depicted at slightly higher velocities than the dripping regime but still at relatively low Weber numbers[4, 19, 24, 25]. In this regime, the jet velocities are low enough that aerodynamic effects are negligible. The breakup of the liquid jet is primarily driven by surface tension forces, which induce axisymmetric disturbances along the jet surface. These disturbances grow in amplitude due to the Rayleigh-Plateau instability until they reach a wavelength approximately equal to the jet radius; at this point, the jet disintegrates into droplets. This regime is characterized by small, periodic surface disturbances and the formation of generally uniform droplets corresponding closely to the diameter of the original jet.

The wind-induced regime[38], also referred to as the sinuous regime[26, 50], is characterized by longer wavelength waves in the jet[41]. This regime is observed at intermediate liquid Weber numbers (WeWe)[4, 19, 24, 25]. As the Weber number increases, the wavelengths of these waves progressively shorten[41]. In this regime, aerodynamic forces play a significant role in the breakup process. The jet forms a wavy appearance due to sinusoidal oscillations around its axis. These oscillations are amplified by aerodynamic forces acting on the jet, leading to its disintegration into droplets. The droplets formed in this regime are comparable in size to the diameter of the jet, and tiny droplets also formed due to the breakup of the threads. The wind-induced regime is distinguished by its higher liquid Weber numbers, indicating that inertial forces are now more significant relative to surface tension forces, causing the jet to break up in a manner driven by both aerodynamic and surface tension effects. Further increases in jet velocity lead to the wind-induced regime with short wavelength waves and, ultimately, atomization. Our experimental setup allows us to achieve a water tank pressure (PP) of up to 120 psi, resulting in a maximum liquid Weber number of 6113 for an 18-gauge needle. Consequently, we can only achieve the breakup regime up to the wind-induced breakup with long wavelength waves.

Figure 6 illustrates the complex interaction between two key parameters influencing breakup dynamics: the needle exit area ratio (ArA_r) and the liquid Weber number (WeWe). In the figure, red diamonds denote instances of the dripping regime, green squares indicate occurrences of the Rayleigh regime, and black circles represent events within the wind-induced regime. This regime map is essential for understanding how liquid jet breakup modes transition with changes in needle diameter and flow velocity. Note that variations in needle diameter affect ArA_r, thereby altering the Weber number. The figure delineates three distinct flow regimes based on these parameters: dripping occurs at low ArA_r and low WeWe, characterized by steady droplet formation driven by capillary forces. At intermediate ArA_r and WeWe, the Rayleigh regime exhibits periodic instabilities leading to droplet formation, balancing inertial and capillary forces. At high ArA_r and high WeWe, the wind-induced regime dominates, featuring atomization of the fluid stream due to strong aerodynamic interactions and high flow velocities.

Figure 6. Regime map demarcating different breakup behaviours in WeWe–ArA_r space.

Jet breakup length

fig:7a presents the liquid jet breakup length of a circular jet under varying water tank pressures, highlighting the evolution of jet breakup length as pressure increases from 10 to 120 psi, increasing the liquid Weber number from 0.6 to 21.2, and the Reynolds number from 108 to 630. The jet breakup length is the distance from the orifice or needle exit to the point where the jet disintegrates into droplets. The red arrows mark the locations where the liquid jet separates, forming discrete droplets or ligaments. Initially, the jet breakup length shows a linear increase with rising pressure, indicative of a laminar regime where the jet remains relatively stable. This linear trend continues up to 25 psi (We=2.6We = 2.6 and Re=219Re = 219); at this point, the jet is firmly within the Rayleigh breakup regime. Here, the stability of the jet decreases, reaching a peak breakup length before transitioning

into a regime characterized by increased instability. As the pressure increases beyond 25 psi (We=2.6We = 2.6 and Re=219Re = 219), the breakup length decreases, reaching its lowest point around 100 psi (We=17.9We = 17.9 and Re=579Re = 579). This decrease is due to the jet entering a more unstable phase due to increasing velocity and surface disturbances. The enlarged view of the surface disturbances is shown in Figure 7b from 50 to 120 psi (We=7.8We = 7.8 to 21.2 and Re=383Re = 383 to 630). However, as the pressure increases to 120 psi (We=21.2We = 21.2 and Re=630Re = 630), the breakup length increases again, albeit with a smaller slope than the initial linear rise. This non-monotonic behaviour in the jet breakup length is a typical pattern observed in numerous studies[19, 20, 23, 24, 25, 35, 37, 51]. The phenomenon of the breakup length can be explained as follows: As the Weber number increases, the jet breakup length initially extends in the laminar and Rayleigh regimes due to the dominance of surface tension forces. As the Weber number rises further, the breakup length decreases as the liquid jet transitions to a semi-turbulent state, where turbulent disturbances enhance the breakup process. However, with continued increases in the Weber number, the weakening of surface tension forces allows the jet to stabilize, leading to a subsequent increase in breakup length. A more detailed explanation of this behavior is provided in Figure 9, which illustrates the relationship between the Weber number and jet breakup length. The surface disturbances and the breakup of the jet occur well within the laminar flow and Rayleigh breakup regime despite showing a different jet length breakup trend. The jet breakup length variation thus illustrates a non-linear relationship between pressure and jet breakup length, with distinct phases corresponding to different breakup regimes. The jet remains stable and laminar at lower pressures, while higher pressures induce instability and more rapid breakup. Beyond a critical pressure, the jet transitions again, showing increasing breakup length. These observations align with findings from other studies[19, 20, 23, 35, 37, 51], suggesting that the jet breakup length will continue to increase with further pressure increments beyond 120 psi (We=21.2We = 21.2).

Figure 7. (a) The breakup of a circular liquid jet across a range of water tank pressures from 10 to 120 psi, with corresponding Weber number values indicated at the top of each panel. The needle exit area ratio is fixed at Ar=10A_r = 10. Red arrows denote the location of the jet breakup, while blue circles emphasize the presence of large droplets and ligaments. (b) The enlarged view of the red dashed region in panel (a) illustrates the surface disturbances of the jet at pressures ranging from 50 to 120 psi.

Figure 9. Stability curve depicting the dimensionless mean jet breakup length (Lj=Lavg/DL_j = L_{\mathrm{avg}}/D) plotted against the Weber number (WeWe) for different needle exit area ratios (ArA_r). Here, LavgL_{\mathrm{avg}} represents the mean jet length observed over time. Error bars indicate the temporal variability in LjL_j. The size of the circle symbols increases with larger needle exit diameters, while black squares denote data points sourced from Ref.[25].

To evaluate the stability of the jet, we analyze the variation in the temporal evolution of the jet breakup length, defined as the distance from the orifice or needle exit to the point where the jet disintegrates into droplets. This parameter is crucial for understanding the jet’s stability under varying operating conditions. Figure 8 displays histograms illustrating the number probability density function (PnP_n) for the instantaneous jet breakup length, LL (mm), for different conditions considered in this study. These histograms depict the probability of observing specific ranges of jet breakup lengths over 300 instances, providing insights into the stability of the liquid jet over time. Figure 8(a, Figure 8b, Figure 8c), Figure 8(d, Figure 8e, Figure 8f), and Figure 8(g, Figure 8h, Figure 8i) correspond to needle exit area ratios (ArA_r) of 4.5, 26, and 66, respectively. Panels (a, d, g) represent situations with water tank pressures of P=40P = 40 psi, panels (b, e, h) of P=80P = 80 psi, and panels (c, f, i) of P=120P = 120 psi. Each panel also indicates the corresponding liquid Weber number (WeWe). The number probability density function (PnP_n) quantifies the relative likelihood of different breakup lengths occurring within each experimental condition, offering a statistical view of jet breakup stability.

Figure 8. Histograms depicting the number probability density function (PnP_n) for jet breakup length, LL (mm), over time are shown for nine different cases, illustrating the stability of the jet under varying conditions. Panels (a, b, c), (d, e, f), and (g, h, i) correspond to needle exit area ratios (ArA_r) of 4.5, 26, and 66, respectively. Panels (a, d, g), (b, e, h), and (c, f, i) represent water tank pressures (PP) of 40, 80, and 120 psi, respectively. Here, the corresponding liquid Weber number (WeWe) is also indicated in each panel.

Figure 8(a) shows the histogram of the probability distribution function (PDF) for the variation in jet breakup length (LL) for Ar=4.5A_r = 4.5 and We=0.6We = 0.6. The narrow distribution and prominent histogram peak indicate minimal variation in jet breakup length over time, reflected by a lower standard deviation. Here, the average jet breakup length is Lavg=9.54L_{avg} = 9.54 mm, with a standard deviation of Lstd=0.51L_{std} = 0.51 mm. As the water tank pressure increases, the jet length increases, accompanied by a more significant variation in jet length, as shown in Figure 8(b), where We=2.3We = 2.3. In this case, the average jet length is Lavg=14.55L_{avg} = 14.55 mm with a standard deviation of Lstd=1.54L_{std} = 1.54 mm, indicating decreased jet stability with increased pressure. Further increasing the pressure results in a decrease in the average jet length to Lavg=11.66L_{avg} = 11.66 mm but with the same standard deviation (Lstd=1.55L_{std} = 1.55 mm), as depicted in the histogram for Figure 8(c) with We=4.1We = 4.1. This reduction in jet length occurs because the jet stability remains within the Rayleigh breakup regime, initiating minimal surface disturbances. Increasing the needle exit area ratio to Ar=26A_r = 26 leads to a substantial increase in the Weber number compared to the previous case (Ar=4.5A_r = 4.5). As the water tank pressure increases from 40, 80, to 120 psi, the corresponding Weber numbers increase to We=39.9We = 39.9, 89.3, and 141.9, respectively, as shown in Figure 8(d,Figure 8e,Figure 8f). In these cases, the average jet length (LavgL_{avg}) increases from 14.05 mm, 19.27 mm, to 21.26 mm, with the standard deviation (LstdL_{std}) increasing from 1.96 mm, 2.79 mm, to 3.13 mm. This trend is visually represented by the histograms in Figure 8(d, Figure 8e, Figure 8f), where the widening of the distribution (increasing width of bars) and a slight decrease in peak height indicate a broader range of jet lengths due to higher mean values and standard deviations. As pressure increases, the jet length extends, following the second slope described in Figure 7. These Weber number ranges lie between the Rayleigh and wind-induced regimes, signifying a transitional region where jet instability intensifies with higher Weber numbers.

Inspection of the results for Ar=66A_r = 66 (Figure 8(g-Figure 8i)) reveals that increasing the pressure leads to an increase in the average jet length (LavgL_{avg}) from 36.57 mm to 48.68 mm to 56.25 mm, with the standard deviation (LstdL_{std}) rising from 5.13 mm to 6.27 mm to 7.29 mm for We=353.4We = 353.4, 680.5, and 982.4, respectively. The decreasing peak height and increasing width of the bars in the histograms further confirm this trend. Observing from top to bottom in Figure 8, as the needle exit area ratio increases, the distribution of jet lengths becomes wider due to increased instability in the jet. In Figure 8(a-Figure 8f), it can be seen that the breakup length decreases within the Rayleigh breakup regime, indicating greater stability, as evidenced by the narrower distribution of the histograms. However, with further increases in the Weber number, the regime shifts to the wind-induced regime, as shown by the more spread-out histograms in Figure 8(g-Figure 8i). This observation aligns with findings by Rezayat, Farshchi, and Berrocal [35], which demonstrate that jet breakup length varies considerably across different regimes. Specifically, the atomization regime exhibits a broader distribution of breakup lengths compared to the Rayleigh and wind-induced regimes, which display less dispersed breakup lengths under lower velocity conditions.

Figure 9 illustrates the stability curve for the dimensionless mean jet breakup length (LjL_j) as a function of the Weber number (WeWe) for various needle exit area ratios (ArA_r). The error bars denote the temporal variation in jet length. The increasing size of the circle symbols represents increasing needle exit diameters. The black squares indicate the variation in jet length with Weber number as reported by Wang and Fang [25]. The stability curve demonstrates a non-monotonic relationship between the jet breakup length and Weber number within the observed regime, consistent with findings from other studies[23, 37, 51]. As the water tank pressure, and consequently the liquid Weber number, increases, the jet breakup length grows within the laminar flow and Rayleigh breakup regimes for Ar=1A_r = 1 to 17, reaching a maximum length of Lj=146.27L_j = 146.27. In these conditions, the surface tension force is the primary mechanism driving the breakup, with the jet length peaking in the Weber number range 2.56≤We≤4.072.56 \le We \le4.07. As the Weber number increases further, the jet breakup length begins to decrease. The central portion of the liquid jet transitions to a semi-turbulent state, as previously described and shown in Figure 7. In this phase, the breakup length diminishes with increasing Weber number until it reaches a minimum value of Lj=48.65L_j = 48.65. This reduction in breakup length continues for cases with ArA_r from 4.5 to 17, with the decreasing trend observed until the Weber number reaches the range 17.89≤We≤20.9317.89 \le We \le20.93 for Ar=10A_r = 10 and 17. Turbulent core disturbances enhance the breakup process, reducing the breakup length. Thus, flow turbulence acts as a secondary mechanism influencing the breakup, while surface tension remains the primary factor. It can be observed that for Ar=10−270A_r = 10 - 270, the jet breakup length starts to increase again, but with a smaller slope compared to the initial increase, as the Weber number rises from We=20.93We = 20.93. Increasing the Weber number up to 6000 underscores the growing significance of flow turbulence. Numerous researchers have

identified liquid turbulence as a critical factor in the wind-induced regime, acting as a primary mechanism for the jet breakup (e.g., Refs.19,24,41). As the liquid jet velocity increases, aerodynamic forces also become influential, serving as a secondary mechanism impacting the breakup process. In this regime, the breakup length increases with higher liquid velocity, reaching Lj=147.2L_j = 147.2 in our study. This increase is attributed to the stabilizing effect of turbulence on the breakup process[35, 52].

Droplet size distribution

The temporal evolution of a jet breakup phenomenon is presented in Figure 10 for Ar=26A_r = 26 and We=13.49We = 13.49. This image sequence primarily highlights three critical aspects of the jet breakup process: the jet breakup point (red arrows), the coalescence of droplets (blue arrows), and the formation of tiny droplets from the liquid thread (white arrows). The red arrows in the figure indicate the jet breakup point caused by the Rayleigh-Plateau instability. This phenomenon occurs when surface tension forces lead a cylindrical fluid jet to break into smaller droplets, forming discrete droplets or ligaments. The instability occurs in the Rayleigh regime, where the wavelength of the perturbations on the jet surface dominates the breakup. This Rayleigh breakup process indicates the transition from a continuous jet to separated droplets[53]. The blue arrows in Figure 10 highlight the coalescence of droplets. At T=1.5T = 1.5, two droplets begin to approach each other and eventually merge by T=4.5T = 4.5. The coalesced droplet then oscillates along the impact axis, completing one oscillation cycle from T=6.0T = 6.0 to T=11.9T = 11.9. During this oscillation, the droplet adopts a prolate shape at T=6.0T = 6.0 and T=11.9T = 11.9 and an oblate shape at T=8.9T = 8.9. This oscillatory behaviour, which reduces the surface area of the merged droplet, is undesirable in many applications. The damping of these oscillations is attributed to viscous dissipation, where internal friction within the fluid gradually diminishes the motion[54, 55].

Figure 10. Temporal evolution of jet breakup dynamics for Ar=26Ar = 26 and We=13.49We = 13.49. The values of the dimensionless time (TT) are indicated at the bottom of each image. The red arrows indicate jet breakup points due to Rayleigh-Plateau instability, the blue arrows show droplet coalescence with oscillations, and the white arrows mark the formation of tiny satellite droplets from the liquid thread. Enlarged views depict thread breakup and tiny droplet generation.

tributed to viscous dissipation, where internal friction within the fluid gradually diminishes the motion[54, 55]. In the study by Pal et al. 56, coalescence is prominently displayed in the collision dynamics of drops under specific combinations of velocity and droplet radius ratios, merging two drops into a larger single drop upon collision. According to Viswanathan 57, simulations reveal that the oscillatory motion of droplets during downstream travel, typically dampened by viscous effects, significantly influences the coalescence and breakup dynamics of primary droplets in the jetting regime. The white arrows in the figure indicate the formation of tiny satellite droplets from the liquid thread. These small droplets form as a result of the breakup of the liquid thread, illustrating the intricate dynamics and fine-scale structures that develop during the jet breakup process. This phenomenon is indicated at T=1.5T = 1.5 and T=11.9T = 11.9, where the Rayleigh-Plateau instability manifests within the jet, resulting in the formation of a thread at the breakup point. The further stretching of the bottom droplets or ligaments separates them from the main jet stream at the top and bottom points of the thread. Consequently, the thread remains and eventually converts into a tiny droplet, as marked at T=3.0T = 3.0 and T=13.4T = 13.4. This breakup process, wherein the jet forms a thread and subsequently a small droplet, significantly influences the droplet size distribution. The detailed effect of this process on droplet size distribution is discussed further in Figure 12. Additionally, Kovalchuk and Simmons 46 demonstrated that the transition from dripping to jetting in surfactant-laden liquids occurs at a critical Weber number, underscoring the importance of surface tension in satellite droplet formation. This transition highlights how surface tension plays a crucial role in the dynamics of satellite droplet generation and overall droplet size distribution within the jetting regime.

Figure 12. Droplet size distribution following the breakup of a liquid jet, depicted as histograms showing the number probability density function (PnP_n) for droplet diameters (dd) in μm\mu\mathrm{m} for twelve different cases. Panels (a, b, c), (d, e, f), (g, h, i), and (j, k, l) correspond to needle exit area ratios (ArA_r) of 4.5, 17, 26, and 66, respectively. Panels (a, d, g, j), (b, e, h, k), and (c, f, i, l) are associated with P=40P = 40 psi, 80 psi, and 120 psi, respectively. The value of WeWe is indicated in each panel.

The number mean diameter (d10d_{10}) and the Sauter mean diameter (d32d_{32}) are crucial metrics for characterizing the distribution of satellite droplets formed during the breakup of a liquid jet. These metrics offer valuable insights into the size distribution of the droplets, which is essential for understanding various jet dynamics and spray processes. The number-based mean diameter (d10d_{10}) represents the arithmetic average of the diameters of all droplets in a sample, weighted by the number of droplets of each diameter. This is given by

d10=∫0∞d⋅p(d) dd,(1)d_{10} = \int_{0}^{\infty} d \cdot p(d)\,\mathrm{d}d, \tag*{(1)}

where p(d)p(d) is the probability density function of the droplet diameters, and dd represents the diameter of droplets. This metric provides a straightforward average diameter, giving equal importance to each droplet irrespective of its size.

The Sauter mean diameter (SMD or d32d_{32}) represents the surface area moment mean of the droplet size distribution, considering both the surface area and volume of the droplets. This metric provides a weighted average that emphasizes the surface area, and is given by

d32=∫0∞d3p(d) dd∫0∞d2p(d) dd,(2)d_{32} = \frac{\int_{0}^{\infty} d^{3}p(d)\,\mathrm{d}d}{\int_{0}^{\infty} d^{2}p(d)\,\mathrm{d}d}, \tag*{(2)}

To enable comparison across different needle exit diameters (DD), both the number mean diameter (d10d_{10}) and the Sauter mean diameter (d32d_{32}) are normalized as d10/Dd_{10}/D and d32/Dd_{32}/D, respectively, and are plotted against the Weber number (WeWe) for various needle exit area ratios (ArAr) in Figure 11a and Figure 11b. Figure 11 demonstrates that as the Weber number increases, the normalized number mean and Sauter mean diameters decrease for needle exit area ratios ArAr ranging from 1 to 17. Specifically, d10/Dd_{10}/D decreases from 5 to 2, and d32/Dd_{32}/D decreases from 5.5 to 2.5 with increasing WeWe. This trend indicates that as pressure increases for individual needles, the number-mean and Sauter mean diameters decrease relative to the needle exit diameter (DD). The peaks observed for needle exit area ratios Ar=10Ar = 10, 17, and 26 associated with We=18We = 18 in Figure 11b coincide with instances where the jet breaks up into droplets or ligaments, forming larger chunks and ligaments. These large chunks or ligaments persist in the flow after the breakup, as indicated by the blue circles in Figure 7a. They travel faster and coalesce with smaller droplets, thereby increasing in size. Consequently, while the volume remains comparable to nearby cases, the surface area of the droplets significantly decreases, resulting in peaks in the Sauter mean diameter. At this intermediate Weber number (We=18We = 18), a balance exists between inertial and surface tension forces, leading to a more irregular breakup process where larger droplets and ligaments intermittently form, contributing to the observed peak in the Sauter mean diameter plot. Therefore, the transition between the Rayleigh and transitional regimes preceding the wind-induced regime occurs at We=18We = 18 for this set of parameters. In this transitional regime, inertial forces and flow turbulence dominate the breakup process before fully transitioning into the wind-induced regime. For Ar=26Ar = 26 and 66, d10d_{10} and d32d_{32} remain relatively constant with increasing Weber number. This constancy occurs because these needle exit area ratios fall within the transitional and wind-induced regimes. Significant changes in droplet diameters occur primarily with larger variations in Weber numbers within these regimes. Thus, for Ar=26Ar = 26 and 66, the Weber number range corresponds to regimes where the number-mean and Sauter mean diameters exhibit minimal variation, unaffected by small changes in Weber number.

Figure 11. Variation of (a) normalised number mean diameter (d10/Dd_{10}/D) and (b) Sauter mean diameter (d32/Dd_{32}/D) with the Weber number (WeWe) for different values of ArA_r.

Figure 12 provides the droplet size distribution, illustrating the number probability density function (PnP_n) for droplet diameters after jet breakup for twelve cases. The present study considers the droplet size distribution for twelve distinct cases, as shown in Figure 12. The histograms in this figure depict the number probability density function (PnP_n) for droplet diameters (dd) post-jet breakup. Here, Figure 12a, Figure 12b, Figure 12c, Figure 12d, Figure 12e, Figure 12f, Figure 12g, Figure 12h, Figure 12i, and Figure 12j, Figure 12k, Figure 12l, corresponding to Ar=4.5Ar = 4.5, 17, 26, and 66, respectively. In Figure 12, panels (a, d, g, j), (b, e, h, k), and (c, f, i, l) are for P=40P = 40 psi, 80 psi, and 120 psi, respectively. It can be observed that as the water tank pressure increases (leading to an increase in jet velocity) for all the needle exit area ratios considered, the size distribution shows minimal change because there is no significant variation in the relative Weber number. However, examining changes in needle exit area ratios from top to bottom panels reveals a shift in the peak towards larger droplet diameters, indicating that droplets become larger as the needle diameter increases. Additionally, as the needle exit area ratio increases from top to bottom panels, the Weber number also increases significantly. This increase in the Weber number, indicative of higher jet velocity, leads to the formation of smaller satellite droplets following the thread breakup. These satellite droplets are also discussed in Figure 10. Notably, in the case of Ar=26A_r = 26, the first peak observed due to tiny droplets starts to form and becomes more pronounced in the case of Ar=66A_r = 66. This transition occurs because the needle exit area ratio, Ar=66A_r = 66 cases, falls under the wind-induced regime. As the liquid jet velocity rises, aerodynamic forces become significant in this regime, serving as a secondary mechanism that influences the thread breakup process and consequently produces a more substantial number of tiny droplets. In summary, increasing the needle exit area ratio (ArA_r) results in a larger needle exit diameter. At constant water tank pressure, this leads to an increased jet velocity, which in turn raises the Weber number. The increased Weber number causes the breakup regime to transition from Rayleigh to wind-induced, thereby transforming the droplet size distribution from a mono-modal distribution at Ar=4.5A_r = 4.5 and 17 to a bi-modal distribution at Ar=26A_r = 26 and 66. This shift highlights the complex interplay between surface tension, which acts as the primary breakup mechanism, and aerodynamic forces, which serve as the secondary breakup mechanism. This underscores the importance of considering these factors when optimizing application atomization processes.

Conclusions

We investigate the dynamics of a water jet injected from a needle and the resulting size distribution through systematic experiments that vary jet velocity and needle exit diameter. Our experimental setup includes a pressurized water dispensing system and a high-speed camera to capture jet dynamics, supported by a shadowgraph imaging system for detailed analysis. Three breakup regimes—dripping, Rayleigh, and wind-induced regimes, are identified, each displaying unique dynamics influenced by surface tension and aerodynamic forces. A regime map is constructed to delineate distinct breakup behaviours in the We−ArWe - A_r space. In the dripping regime, observed at low WeWe numbers, individual droplets form and are dispensed one by one from the needle tip without forming a continuous jet. At intermediate Weber numbers, the jet exhibits the Rayleigh breakup, where the Rayleigh-Plateau instability causes the jet to disintegrate into droplets. As the Weber number increases further, the jet displays wind-induced breakup, characterized by significant aerodynamic forces influencing the breakup process. Droplets formed in this regime are comparable in size to the diameter of the jet, with tiny droplets also forming due to the breakup of threads. Our observations indicate a linear increase in jet breakup length with pressure, signifying stable laminar flow up to a Weber number of We=4.07We = 4.07. Beyond this threshold, increased pressure induces surface instability, shortening breakup length. At higher pressures, breakup length increases again, marking a transition to the wind-induced regime dominated by aerodynamic effects. The study further reveals that increasing the Weber number decreases the normalized number-mean and Sauter mean diameters. Histograms depicting the probability density function show variations corresponding to jet breakup length, with the droplet size distribution being mono-modal in the Rayleigh regime and bi-modal in the wind-induced regime. It is to be noted that understanding the distribution of droplet sizes following the breakup of a liquid jet is crucial for optimizing atomization processes, which are integral to applications such as fuel injection, agricultural spraying, and pharmaceutical formulations. Analyzing droplet size distribution provides insights into the efficiency of these processes, enabling enhanced performance and effectiveness of spray systems for various industrial applications and natural phenomena.

Acknowledgments

K.C.S. thanks IIT Hyderabad for the financial support through grant IITH/CHE/F011/SOCH1.

AUTHOR DECLARATIONS

Conflict of Interest

The authors have no conflicts to disclose.

Author Contributions

Pavan Kumar Kirar: Investigation (equal); Methodology (equal); Writing – original draft (equal). Nikhil Kumar: Investigation (equal); Methodology (equal); Writing – original draft (equal). Kirti Chandra Sahu: Conceptualization; Supervision; Writing – review & editing.

Data Availability Statement

The data that support the findings of this study are available from the corresponding author upon reasonable request.

References

  1. [1]M. Broumand and M. Birouk, “Liquid jet in a subsonic gaseous crossflow: Recent progress and remaining challenges,” Prog. Energy Combust. Sci. 57, 1–29 (2016).DOI
  2. [2]M. Hashemi, S. Shalhaf, M. Jadidi, and A. Dolatabadi, “Effects of gas viscosity and liquid-to-gas density ratio on liquid jet atomization in crossflow,” AIP Adv. 13, 035105 (2023).DOI
  3. [3]S. Mousavi, M. Siavashi, and M. Bagheri, “Comparison of the jet breakup and droplet formation between non-Newtonian and Newtonian fluids,” J. Non-Newtonian Fluid Mech. 321, 105093 (2023).DOI
  4. [4]Z. W. Wu, H. Zhao, W. F. Li, J. L. Xu, S. Wang, and H. F. Liu, “Effects of inner bubble on liquid jet breakup,” Phys. Fluids 31, 034107 (2019).DOI
  5. [5]B. Lopez, A. Soucamarianadin, and P. Attané, “Breakup of continuous liquid jets: effect of nozzle geometry,” J. Imaging Sci. Technol. 43, 145–152 (1999).DOI
  6. [6]J. M. López-Herrera and A. M. Gañán-Calvo, “A note on charged capillary jet breakup of conducting liquids: experimental validation of a viscous one-dimensional model,” J. Fluid Mech. 501, 303–326 (2004).DOI
  7. [7]S. S. Ade, P. K. Kirar, L. D. Chandrala, and K. C. Sahu, “Droplet size distribution in a swirl airstream using in-line holography technique,” J. Fluid Mech. 954, A39 (2023).DOI
  8. [8]S. S. Ade, L. D. Chandrala, and K. C. Sahu, “Size distribution of a drop undergoing breakup at moderate weber numbers,” J. Fluid Mech. 959, A38 (2023).DOI
  9. [9]S. K. Soni, P. K. Kirar, P. Kolhe, and K. C. Sahu, “Deformation and breakup of droplets in an oblique continuous air stream,” Int. J. Multiphase Flow 122, 103141 (2020).arxiv.org/abs/1907.02962
  10. [10]P. K. Kirar, S. K. Soni, P. S. Kolhe, and K. C. Sahu, “An experimental investigation of droplet morphology in swirl flow,” J. Fluid Mech. 938, A6 (2022).DOI
  11. [11]M. G. Faeth, L.-P. Hsiang, and P.-K. Wu, “Structure and breakup properties of sprays,” Int. J. Multiphase Flow 21, 99–127 (1995).DOI
  12. [12]D. R. Guildenbecher, C. López-Rivera, and P. E. Sojka, “Secondary atomization,” Exp. Fluids 46, 371–402 (2009).DOI
  13. [13]A. H. Lefebvre and V. G. McDonnell, Atomization and Sprays (CRC press, 2017).
  14. [14]S. P. Lin and R. D. Reitz, “Drop and spray formation from a liquid jet,” Annu. Rev. Fluid Mech. 30, 85–105 (1998).DOI
  15. [15]J. H. Hilbing and S. D. Heister, “Droplet size control in liquid jet breakup,” Phys. Fluids 8, 1574–1581 (1996).
  16. [16]A. M. Sterling and C. A. Sleicher, “The instability of capillary jets,” J. Fluid Mech. 68, 477–495 (1975).DOI
  17. [17]C. C. Miesse, “Correlation of experimental data on the disintegration of liquid jets,” Ind. Eng. Chem. Res. 47, 1690–1701 (1955).DOI
  18. [18]M. P. Borthakur, G. Biswas, D. Bandyopadhyay, and K. C. Sahu, “Dynamics of an arched liquid jet under the influence of gravity,” Eur. J. Mech. B Fluids 74, 1–9 (2019).DOI
  19. [19]M. Birouk and N. Lekic, “Liquid jet breakup in quiescent atmosphere: A review,” At. Sprays 19, 501–528 (2009).DOI
  20. [20]P. R. Grant and S. Middleman, “Newtonian jet stability,” AIChE J. 12, 669–678 (1966).
  21. [21]B. Srinivasan and A. Sinha, “Primary breakup of liquid jet—effect of jet velocity profile,” Phys. Fluids 36, 032102 (2024).arxiv.org/abs/2310.08515
  22. [22]N. O. Tanase, I. R. Răuceanu, and C. Balan, “Experimental and numerical investigations of the jetting regime,” in IOP Conf. Ser.: Earth Environ. Sci., Vol. 1136 (IOP Publishing, 2023) p. 012038.DOI
  23. [23]D. Kiaoulis, T. Travis, J. Moore, and G. Risha, “Evaluation of orifice inlet geometries on single liquid injectors through cold-flow experiments,” Exp. Therm. Fluid Sci. 103, 78–88 (2019).DOI
  24. [24]P. Sharma and T. Fang, “Breakup of liquid jets from non-circular orifices,” Exp. Fluids 55, 1–17 (2014).DOI
  25. [25]F. Wang and T. Fang, “Liquid jet breakup for non-circular orifices under low pressures,” Int. J. Multiphase Flow 72, 248–262 (2015).DOI
  26. [26]M. P. Borthakur, G. Biswas, and D. Bandyopadhyay, “Formation of liquid drops at an orifice and dynamics of pinch-off in liquid jets,” Phys. Rev. E. 96, 013115 (2017).DOI
  27. [27]K. R. Rajesh, R. Sakthikumar, and D. Sivakumar, “Interfacial oscillation of liquid jets discharging from non-circular orifices,” Int. J. Multiphase Flow 87, 1–8 (2016).DOI
  28. [28]L. Geng, Y. Wang, Y. Wang, and H. Li, “Effect of the injection pressure and orifice diameter on the spray characteristics of biodiesel,” J. Traffic Transp. Eng. (Engl. Ed.) 7, 331–339 (2020).DOI
  29. [29]K. R. Rajesh, V. Kulkarni, S. K. Vankeswaram, R. Sakthikumar, and S. Deivandren, “Drop size characteristics of sprays emanating from circular and non-circular orifices in the atomization regime,” J. Aerosol Sci. 174, 106245 (2023).DOI
  30. [30]M. Tadjfar and A. Jaberi, “Effects of aspect ratio on the flow development of rectangular liquid jets issued into stagnant air,” Int. J. Multiphase Flow 115, 144–157 (2019).DOI
  31. [31]M. R. Morad, M. Nasiri, and G. Amini, “Axis-switching and breakup of rectangular liquid jets,” Int. J. Multiphase Flow 126, 103242 (2020).DOI
  32. [32]A. Jaberi and M. Tadjfar, “Wavelength and frequency of axis-switching phenomenon formed over rectangular and elliptical liquid jets,” Int. J. Multiphase Flow 119, 144–154 (2019).DOI
  33. [33]S. Kooij, R. Sijs, M. M. Denn, E. Villermaux, and D. Bonn, “What determines the drop size in sprays?” Phys. Rev. X 8, 031019 (2018).DOI
  34. [34]A. Roth, D. Frantz, W. Chaze, A. Corber, and E. Berrocal, “High-speed imaging database of water jet disintegration part i: Quantitative imaging using liquid laser-induced fluorescence,” Int. J. Multiphase Flow 145, 103641 (2021).DOI
  35. [35]S. Rezayat, M. Farshchi, and E. Berrocal, “High-speed imaging database of water jet disintegration part ii: Temporal analysis of the primary breakup,” Int. J. Multiphase Flow 145, 103807 (2021).DOI
  36. [36]T. Kang, Q. Yu, Z. Liu, and S. Tao, “Effect of velocity and radius distribution on jet breakup,” Phys. Fluids 35, 014103 (2023).DOI
  37. [37]Y. Zhan, Y. Kuwata, K. Maruyama, T. Okawa, K. Enoki, M. Aoyagi, and T. Takata, “Effects of surface tension and viscosity on liquid jet breakup,” Exp. Therm. Fluid Sci. 112, 109953 (2020).DOI
  38. [38]E. Farvardin and A. Dolatabadi, “Numerical simulation of the breakup of elliptical liquid jet in still air,” J. Fluids Eng. Trans. ASME 135, 071302 (2013).
  39. [39]C. Li, C. Li, X. Xiao, Q. Li, and Y. Zhu, “Experimental study of spray characteristics of liquid jets in supersonic crossflow,” Aerosp. Sci. Technol. 95, 105426 (2019).DOI
  40. [40]A. Chakraborty, S. Sahu, and D. Maurya, “Effect of orifice size on liquid breakup dynamics and spray characteristics in slinger atomizers,” Proc. Inst. Mech. Eng. A: J. Power Energy 236, 1158–1170 (2022).DOI
  41. [41]R. D. Reitz, Atomization and other breakup regimes of a liquid jet. (Princeton University, 1978).
  42. [42]J. R. Richards, A. M. Lenhoff, and A. N. Beris, “Dynamic breakup of liquid–liquid jets,” Phys. Fluids 6, 2640–2655 (1994).DOI
  43. [43]N. Machicoane, R. Osuna-Orozco, and A. Aliseda, “Regimes of the length of a laminar liquid jet fragmented by a gas co-flow,” Int. J. Multiphase Flow 165, 104475 (2023).DOI
  44. [44]A. Dunand, J.-L. Carreau, and F. Roger, “Liquid jet breakup and atomization by annular swirling gas jet,” At. Sprays 15, 223-247 (2005).DOI
  45. [45]C. Daskiran, X. Xue, F. Cui, J. Katz, and M. C. Boufadel, “Impact of a jet orifice on the hydrodynamics and the oil droplet size distribution,” Int. J. Multiphase Flow 147, 103921 (2022).DOI
  46. [46]N. M. Kovalchuk and M. J. Simmons, “Effect of soluble surfactant on regime transitions at drop formation,” Colloids Surf. A: Physicochem. Eng. Asp. 545, 1–7 (2018).DOI
  47. [47]R. J. Furbank and J. F. Morris, “An experimental study of particle effects on drop formation,” Phys. Fluids 16, 1777–1790 (2004).DOI
  48. [48]L. Rayleigh, “On the capillary phenomena of jets,” Proc. R. Soc. Lond. 29, 71–97 (1879).
  49. [49]A. Kalajai, B. Lopez, P. Attané, and A. Soucemarianadin, “Breakup length of forced liquid jets,” Phys. Fluids 15, 2469–2479 (2003).DOI
  50. [50]B. J. Meister and G. F. Scheele, “Prediction of jet length in immiscible liquid systems,” AIChE J. 15, 689–699 (1969).DOI
  51. [51]G. Sun, Y. Zhan, T. Okawa, M. Aoyagi, A. Uchibori, and Y. Okano, “Effects of nozzle orifice shape on jet breakup and splashing during liquid jet impact onto a horizontal plate,” Exp. Therm. Fluid Sci. 151, 111095 (2024).DOI
  52. [52]A. Mansour and N. Chigier, “Dynamic behavior of liquid sheets,” Phys Fluids A, Fluid Dyn 3, 2971–2980 (1991).DOI
  53. [53]A. Javadi, J. Eggers, D. Bonn, M. Habibi, and N. M. Ribe, “Delayed capillary breakup of falling viscous jets,” Phys. Rev. Lett. 110, 144501 (2013).pubmed.ncbi.nlm.nih.gov/25166995
  54. [54]P. K. Kirar, S. D. Pokale, K. C. Sahu, B. Ray, and G. Biswas, “Influence of the interaction of capillary waves on the dynamics of two drops falling side-by-side on a liquid pool,” Phys. Fluids 34, 112114 (2022).DOI
  55. [55]M. Balla, M. K. Tripathi, and K. C. Sahu, “Shape oscillations of a non-spherical water droplet,” Phys. Rev. E 99, 023107 (2019).

Paper details

vlnc:W_rmqjyw2v
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents