betaFeedback

WorksPhysics and Astronomy

Ultralow and Selective Infrared Emission from MXenes

Abstract

Low and selective infrared emission materials are necessary for next generation thermal technologies, including passive heating, infrared identification, and photothermal conversion. Here, we report on the intrinsic infrared radiation properties of three MXenes: Ti3C2Tx, Ti3CNTx, and V4C3Tx. The infrared emissivity of 200 nm thick Ti3C2Tx coating is lower than 0.06 between wavelengths of 3-27 μm, while Ti3CNTx and V4C3Tx have values of 0.13 and 0.26, respectively. Investigation using a laboratory-based passive heating process showed that MXene coatings suppress the thermal radiation. The infrared identification capability was also validated using a patterned MXene fabric. This work paves the way for developing MXene-based smart wearable devices and garments capable of selective and localized thermal management.

Introduction

Modulating thermal radiation in the infrared (IR) range is critical for next generation thermal technologies, such as selective heating/cooling, IR camouflage, thermal circuits, smart textiles, and others.[1, 2, 3, 4] Currently, the state of the art in adaptive radiation heating/cooling uses metamaterials to manipulate the phonon behavior,[5] including topological transitions, photonic crystals, epsilon-near-zero surfaces, and others.[6, 7, 8] However, utilization of these precise engineered structures limits their applications in highly integrated devices and large-scale thermal manipulation components due to cost and scalability issues. Alternative approaches, such as active electrical modulation of thermal emissivity, are promising, but have limited range and rely on the inherent thermal properties of the structures.[9, 10] For passive heating management, low IR emission/absorption is required to suppress energy dissipation by Stefan-Boltzmann’s law. Conventional polished metals (Al, Ag, Ni, etc.) have ultralow IR emissivity (< 0.1), but are difficult to produce; typically, thin metal coatings/films are deposited using magnetron sputtering or electroless plating, especially for the complex architectures.[11, 12] Therefore, it is still challenging to achieve selective thermal radiation using passive intrinsic IR emission material characteristics.

Two-dimensional transition metal carbides and nitrides (MXenes) have shown diverse light-matter interactions in a very broad electromagnetic frequency range,[13, 14] owing to their anisotropic electronic and optical properties, active surfaces, and a high density of states at the Fermi level.[15, 16, 17, 18, 19] For instance, MXenes present active plasmon resonances from the ultraviolet (UV) to near-IR range as a function of structure and composition.[20] 16 different MXene compositions were used for electromagnetic interference (EMI) shielding in gigahertz frequency range and the performance was adjusted by controlling the M-site chemistry.[21, 22] There are a few reports on light-to-heat conversion of Ti3C2Tx\mathrm{Ti}_{3}\mathrm{C}_{2}\mathrm{T}_{x} MXene for thermal management.[23, 24, 25, 26] However, little is known about the intrinsic thermal radiation properties of MXenes, especially in the IR range. Furthermore, more than 30 kinds of stoichiometric MXenes have been experimentally synthesized, with numerous MXene compositions theoretically predicted.[19, 27, 28, 29] It is likely that MXenes will have diverse IR radiation properties depending on the composition, atomic arrangement, and surface chemistry. Moreover, due to the solution processability of MXenes, thin MXene films/coatings from nanometer- to micrometer-thickness can be readily manufactured using multiple techniques.[30, 31, 32] The ease of processing coupled with the natural hydrophilicity and flexibility of MXenes facilitates the deposition of MXenes on a wide variety of surfaces, enabling the rapid treatment of surfaces for thermal management.

Herein, we report preliminary data on the low IR emissivity of three MXene (Ti3C2Tx\mathrm{Ti}_{3}\mathrm{C}_{2}\mathrm{T}_{x}, Ti3CNTx\mathrm{Ti}_{3}\mathrm{CNT}_{x}, and V4C3Tx\mathrm{V}_{4}\mathrm{C}_{3}\mathrm{T}_{x}) coatings for object identification/camouflage and other thermal management applications. MXene-coated glass with different coating thickness was fabricated by a simple spray-coating process. The IR emissivity of different MXene coatings was measured using a Fourier-transform infrared (FTIR) spectrometer based on Kirchhoff’s law of thermal radiation. The IR radiation performance was validated through IR imaging of MXene coatings on a hot plate. As a proof of concept, we also fabricated a Ti3C2Tx\mathrm{Ti}_{3}\mathrm{C}_{2}\mathrm{T}_{x}-patterned cotton fabric for image identification, demonstrating the low thermal radiation of MXene. This work illustrates the potential use of MXenes in films, garments and other systems for selective and localized thermal management.

Results and Discussion

Three different MXenes were synthesized and delaminated into few-layer flakes, as shown in Figure 1a-Figure 1c. Ti3C2Tx\mathrm{Ti}_{3}\mathrm{C}_{2}\mathrm{T}_{x}, Ti3CNTx\mathrm{Ti}_{3}\mathrm{CNT}_{x}, and V4C3Tx\mathrm{V}_{4}\mathrm{C}_{3}\mathrm{T}_{x} flakes had a lateral size of >3> 3 μm\mu\mathrm{m}, >2> 2 μm\mu\mathrm{m}, and >300> 300 nm, respectively. The complete etching and delamination was further confirmed by X-ray diffraction (XRD) patterns of MXene films (Figure 1d). The (002) peaks of Ti3C2Tx\mathrm{Ti}_{3}\mathrm{C}_{2}\mathrm{T}_{x} and Ti3CNTx\mathrm{Ti}_{3}\mathrm{CNT}_{x} are at 7.2∘7.2^\circ (2θ2\theta) while V4C3Tx\mathrm{V}_{4}\mathrm{C}_{3}\mathrm{T}_{x} is at 5.3∘5.3^\circ, indicating that the V4C3Tx\mathrm{V}_{4}\mathrm{C}_{3}\mathrm{T}_{x} film had a larger dd-spacing (16.6 Å). As shown in Raman spectra (Figure 1e), the peaks at 201 cm−1^{-1} and 718 cm−1^{-1} for Ti3C2Tx\mathrm{Ti}_{3}\mathrm{C}_{2}\mathrm{T}_{x} correspond to A1g\mathrm{A}_{1g} (Ti, O, C) and A1g\mathrm{A}_{1g} (C) vibrations.[33] Ti3CNTx\mathrm{Ti}_{3}\mathrm{CNT}_{x} shows a similar spectrum with Ti3C2Tx\mathrm{Ti}_{3}\mathrm{C}_{2}\mathrm{T}_{x}, but with a weaker A1g\mathrm{A}_{1g} (Ti, O, C) vibration (~201 cm−1^{-1}) and the absence of peak at 718 cm−1^{-1} due to the random arrangement of C and N atoms. V4C3Tx\mathrm{V}_{4}\mathrm{C}_{3}\mathrm{T}_{x} shows A1g\mathrm{A}_{1g} vibrations at ~264 cm−1^{-1} and ~660 cm−1^{-1} and Eg\mathrm{E}_{g} vibration at ~480-540 cm−1^{-1}.

Image not extracted

Figure 1. Scanning electron microscopy (SEM) images of three MXene flakes: (a) Ti3C2Tx\mathrm{Ti}_{3}\mathrm{C}_{2}\mathrm{T}_{x}, (b) Ti3CNTx\mathrm{Ti}_{3}\mathrm{CNT}_{x}, and (c) V4C3Tx\mathrm{V}_{4}\mathrm{C}_{3}\mathrm{T}_{x}. (d) XRD patterns and (e) Raman spectra of different MXene coatings.

To investigate the IR emissivity of different MXenes, ~200 nm thick coating of each MXene was fabricated on glass substrates by spray-coating. As shown in Figure 2a, each MXene coating is different visually and under optical microscope, and is commensurate with previous reports.[20] The emissivity (ϵ\epsilon)/absorbance (AA) spectra of MXene coatings were calculated using the measured reflectance (RR) with a FTIR spectrometer over a wavelength range of 0.3-27 μm\mu\mathrm{m}, as shown in Figure 2b. The MXene coatings show low emissivity in mid-IR range (>2.5> 2.5 μm\mu\mathrm{m}) and a nonlinear trend in the UV-vis–NIR range (0.3-2.5 μm\mu\mathrm{m}). The 200 nm thick Ti3C2Tx\mathrm{Ti}_{3}\mathrm{C}_{2}\mathrm{T}_{x} coating has an emissivity of <0.1< 0.1 over the entire mid-IR range, while Ti3CNTx\mathrm{Ti}_{3}\mathrm{CNT}_{x} and V4C3Tx\mathrm{V}_{4}\mathrm{C}_{3}\mathrm{T}_{x} coatings are below 0.2 and 0.4, respectively. Particularly, in the atmospheric window of thermal radiation (e.g. 8-14 μm\mu\mathrm{m}), Ti3C2Tx\mathrm{Ti}_{3}\mathrm{C}_{2}\mathrm{T}_{x}, Ti3CNTx\mathrm{Ti}_{3}\mathrm{CNT}_{x}, and V4C3Tx\mathrm{V}_{4}\mathrm{C}_{3}\mathrm{T}_{x} have an average emissivity of 0.06, 0.13, and 0.26, respectively, implying that MXenes have the capability to suppress thermal radiation. Considering diversity of MXenes in both elemental composition and structure, along with the already known differences in optical and electronic properties, it is probable that other MXenes can achieve selective infrared emission with transparent coatings. However, additional studies are needed to understand the IR radiation mechanism of MXenes.

Image not extracted

Figure 2. (a) The digital (left) and optical (right) images of MXenes (Ti3C2Tx\mathrm{Ti}_{3}\mathrm{C}_{2}\mathrm{T}_{x}, Ti3CNTx\mathrm{Ti}_{3}\mathrm{CNT}_{x}, and V4C3Tx\mathrm{V}_{4}\mathrm{C}_{3}\mathrm{T}_{x}) spray-coated on glass substrates. (b) The emissivity/absorbance of ~200 nm thick MXene coatings in a wavelength range of 0.3–27 μ\mum. The scale bar in optical images is 40 μ\mum.

To validate the low IR emission of MXenes, the MXene-coated glass slides were placed on a hot plate at 110 °C for 300 s with the apparent temperature measured with an IR camera. As shown in Figure 3a, for all three MXenes, the temperature increased rapidly in the first 30 s, and then stabilized after ~300 s. After stabilization, temperatures of 39.5 °C and 44 °C were recorded for Ti3C2Tx\mathrm{Ti}_{3}\mathrm{C}_{2}\mathrm{T}_{x} and Ti3CNTx\mathrm{Ti}_{3}\mathrm{CNT}_{x}, respectively, and attributed to their ultralow IR emission. Because V4C3Tx\mathrm{V}_{4}\mathrm{C}_{3}\mathrm{T}_{x} has a higher emissivity, it exhibits an apparent steady-state temperature of 66.3 °C after 300 s. While higher than the Ti-based MXenes, this detected value is still lower than the real surface temperature of 110 °C, indicating the capability of all tested MXenes to suppress thermal radiation. From the IR images of MXene coatings on a hot plate in different time (Figure 3c), it was visually observed that the temperature changes of different MXene coatings with the increasing time. Ti3C2Tx\mathrm{Ti}_{3}\mathrm{C}_{2}\mathrm{T}_{x} and Ti3CNTx\mathrm{Ti}_{3}\mathrm{CNT}_{x} have a similar color change while V4C3Tx\mathrm{V}_{4}\mathrm{C}_{3}\mathrm{T}_{x} shows larger temperature change from 57.0 to 66.3 °C. We further investigated the thermal radiation behavior of Ti3C2Tx\mathrm{Ti}_{3}\mathrm{C}_{2}\mathrm{T}_{x} using different coating thicknesses (~200, 600, and 1300 nm). As shown in Figure 3b, the steady-state temperature of the 1300 nm thick Ti3C2Tx\mathrm{Ti}_{3}\mathrm{C}_{2}\mathrm{T}_{x} coating is 38.3 °C while the 200 nm coating reaches 39.2 °C. In addition, there is no significant difference for the three samples in the first 30 s which is the rapid heating process. This indicates that the nanometer-thick Ti3C2Tx\mathrm{Ti}_{3}\mathrm{C}_{2}\mathrm{T}_{x} coating has a prominent IR identification performance, which is attributed to its ultralow IR emissivity rather than low thermal conductivity.

Image not extracted

Figure 3. Temperature as a function of time for (a) different MXene coatings (Ti3C2Tx\mathrm{Ti}_{3}\mathrm{C}_{2}\mathrm{T}_{x}, Ti3CNTx\mathrm{Ti}_{3}\mathrm{CNT}_{x}, and V4C3Tx\mathrm{V}_{4}\mathrm{C}_{3}\mathrm{T}_{x}) with a thickness of ~200 nm, and (b) Ti3C2Tx\mathrm{Ti}_{3}\mathrm{C}_{2}\mathrm{T}_{x} coatings with different thicknesses (~200 nm, ~600 nm, and ~1300 nm) on a hot plate at 110 °C. (c) Infrared images of different MXene coatings at different time.

A Ti3C2Tx\mathrm{Ti}_{3}\mathrm{C}_{2}\mathrm{T}_{x} dragon-shaped pattern was sprayed onto a cotton fabric to demonstrate a proof-of-concept application (Figure 4a). When the fabric was worn, the patterned region only reads ∼28 ∘C\sim28\,^\circ\mathrm{C} using the IR camera, which is lower than the uncoated region (∼32 ∘C\sim32\,^\circ\mathrm{C}), as shown in Figure 4b. This demonstrates that a Ti3C2Tx\mathrm{Ti}_{3}\mathrm{C}_{2}\mathrm{T}_{x} coating, even when on a rough, porous, or uneven surfaces, still has a lower IR emissivity. This result indicates that MXene may potentially be used for IR camouflage coatings, IR identification tags, and localized thermal management systems. Compared to traditional metals with low IR emission, MXenes can be more easily integrated with fabrics and complex devices owing to their solution processibility. In addition to IR emission properties, we have demonstrated that MXene-coated fabrics have high-performance EMI shielding in gigahertz ranges.[34] It is promising to develop smart MXene-coated garments with multifunctional capabilities, including IR stealth/identification, EMI shielding, and wireless communication.

Image not extracted

Figure 4. (a) Visible and (b) infrared images of a Ti3C2Tx\mathrm{Ti}_{3}\mathrm{C}_{2}\mathrm{T}_{x}-coated fabric attached on a human body, showing the low infrared emission of Ti3C2Tx\mathrm{Ti}_{3}\mathrm{C}_{2}\mathrm{T}_{x}.

Conclusions

In summary, we have demonstrated that MXenes with different compositions (Ti3C2Tx\mathrm{Ti}_{3}\mathrm{C}_{2}\mathrm{T}_{x}, Ti3CNTx\mathrm{Ti}_{3}\mathrm{CNT}_{x}, and V4C3Tx\mathrm{V}_{4}\mathrm{C}_{3}\mathrm{T}_{x}) have ultralow IR emissivity in the mid-IR range, and show non-linear optical absorbance in UV-vis-NIR range. ∼200\sim200 nm thick Ti3C2Tx\mathrm{Ti}_{3}\mathrm{C}_{2}\mathrm{T}_{x}, Ti3CNTx\mathrm{Ti}_{3}\mathrm{CNT}_{x}, and V4C3Tx\mathrm{V}_{4}\mathrm{C}_{3}\mathrm{T}_{x} films have an average IR emissivity of 0.06, 0.13, and 0.26, respectively, in the atmospheric window. MXene-coated glass shows lower IR-detected temperatures than the heating object. IR identification was achieved in a Ti3C2Tx\mathrm{Ti}_{3}\mathrm{C}_{2}\mathrm{T}_{x}-patterned cotton fabric. This work clearly shows the potential of MXenes for the integration into smart wearables/devices with selective IR identification/stealth, thermal insulation, and localized thermal manipulation with different MXenes.

Methods

Materials

Ti (99.5%, −325 mesh, Alfa Aesar), Al (99.5%, −325 mesh, Alfa Aesar), TiC (99.5%, ∼2\sim2 μm, Alfa Aesar), AlN (98%, 10 μm, Aldrich), V (99.5%, −325 mesh, Alfa Aesar), C (graphite, 99%, −325 mesh, Alfa Aesar), HF (48.5−51%, Acros Organics), HCl (36.5−38%, Fisher Chemical), LiCl (99%, Acros Organics), and tetramethylammonium hydroxide (25 wt%, Acros Organics).

Synthesis of MAX phases

For Ti3_3AlC2_2, the precursor TiC:Ti:Al powders were mixed in an atomic ratio of 2:1.25:2.2, following previous reports. The powders were ball milled at 70 rpm for 18 h in polyethylene bottles with zirconia balls (2:1 mass ratio of balls to powder). The powders were then placed into an alumina crucible, which was placed into a high temperature furnace (Carbolite Gero) and heated at 1400 °C for 2 h. The samples were heated and cooled at a rate of 3 °C/min with Ar continually flowing at 200 ccm. The sintered compact was drilled with a TiN coated bit, then sieved to below 32 μm. The powders were washed with 9 M HCl for 24 h to remove residual intermetallics and metals, then were repeatedly washed with DI water. For Ti3_3AlCN (and V4_4AlC3_3) a similar procedure was followed, except the precursors Ti:AlN:C (V:Al:C) were mixed in a 3:1:1 (4:1.5:3) atomic ratio, and the sample was heated at 1500 °C for 2 h.

Synthesis of Ti3_3C2_2Tx_x and Ti3_3CNTx_x

Ti3_3C2_2Tx_x and Ti3_3CNTx_x were synthesized by the selective etching of the corresponding MAX phase powders (Ti3_3AlC2_2 and Ti3_3AlCN; -325 mesh) with an acids mixture (HF and HCl). The synthesis procedure was reported in our previous work.[21, 35] Typically, 2 mL of HF, 12 mL of HCl, and 6 mL of deionized (DI) water were mixed firstly. After that, 1 g of MAX phase powder was added to the solution and stirred for 24 h at room temperature. After etching, the reacted solution was washed with DI water using the centrifuge at 3500 rpm for 2 mins until pH > 6. The obtained sediment was mixed with 1 g of LiCl in 50 mL of DI water. The mixture was shaken for 15 mins, and then centrifuged at 3500 rpm for 10 mins several times until the sediment was swelled. The swelled sediment was dispersed in DI water and then centrifuged at 7500 rpm for 3 mins. After that, the black supernatant was collected for spray-coating.

Synthesis of V4_4C3_3Tx_x

V4_4C3_3Tx_x were synthesized by the selective etching of V4_4AlC3_3 with HF. 1 g of V4_4AlC3_3 powder was added into 20 mL of HF and stirred at 35 °C for 8 days. After etching, the reacted solution was washed with DI water through centrifugation (3500 rpm, 2 min) until pH > 6. After that, the washed sediment was added into a solution with 1 g of TMAOH and 10 mL of DI water and stirred for 24 h. The mixture was centrifuged several times with DI water at 10000 rpm for 10 mins until pH < 8. At last, the solution was centrifuged at 3500 rpm for 10 min. The supernatant was the dispersion of delaminated V4_4C3_3Tx_x flakes in water.

Fabrication of MXene coatings

MXene coatings was fabricated by spray-coating from MXene aqueous solution. Microscopic glass slide (Fisher Scientific) was used as the substrate. Before spray-coating, the slide was cleaned by ethanol with sonication. The cleaned glass slide was plasma-treated (Tergeo Plus, Pie Scientific) at 100 W with oxygen flow at 3 sccm for 5 mins. MXene colloidal solution with a concentration was sprayed onto the glass substrates manually. The sprayed samples were dried in a vacuum oven at 70 °C for 12 h. MXene-coated cotton fabric was fabricated using a similar process. Before spray-coating, the fabric was washed using a liquid detergent (Synthrapol®).

Characterization

The morphology of MXene flakes was observed using scanning electron microscopy (SEM; Zeiss Supra 50VP, Germany). A 3D laser scanning confocal microscopy (Keyence, VK-X1000, Japan) was used to observe the coating surface and measure the coating. XRD patterns of MXene coatings were measured using a Rigaku SmartLab (Tokyo, Japan) operating at 40 kV/30 mA with Cu Kα\alpha radiation. Raman spectra were measured with an inverted reflection mode Renishaw (2008, Gloucestershire, UK) instrument, equipped with 63×63 \times (NA = 0.7) objectives and a diffraction-based room-temperature spectrometer. The laser line used was 633 nm and the laser power was kept around 0.1 mW. The infrared images and temperature were recorded using an IR camera (FLIR E8xt, USA). The camera emissivity was set as 0.94. The reflectivity (RR) of MXene coatings in UV-vis-MIR range (0.3-27 μ\mum) was measured using a FTIR spectrometer (Invenio-X, Bruker, Germany). The emissivity (ε\varepsilon) was calculated based on Kirchhoff law (ε=1−R\varepsilon=1-R).

Acknowledgements

We thank Dr. Sergey Shilov (Bruker Scientific, LLC) for the emissivity measurement of MXene coatings. XRD and SEM analyses were performed using instruments in the Materials Characterization Core at Drexel University. We thank Geetha Valurouthu for the help with collecting Raman spectra and Kyle Matthews for the assistance with SEM observations.

Conflict of Interest

The authors have filed for a patent on the infrared emission of MXenes. [36] The authors declare no other conflict of interest.

References

  1. [1]Zhang, X. A.; Yu, S.; Xu, B.; Li, M.; Peng, Z.; Wang, Y.; Deng, S.; Wu, X.; Wu, Z.; Ouyang, M.; Wang, Y., Dynamic gating of infrared radiation in a textile. Science 2019, 363 (6427), 619-623.DOI
  2. [2]Ergoktas, M. S.; Bakan, G.; Kovalska, E.; Le Fevre, L. W.; Fields, R. P.; Steiner, P.; Yu, X.; Salihoglu, O.; Balci, S.; Fal’ko, V. I.; Novoselov, K. S.; Dryfe, R. A. W.; Kocabas, C., Multispectral graphene-based electro-optical surfaces with reversible tunability from visible to microwave wavelengths. Nature Photonics 2021, https://doi.org/10.1038/s41566-021-00791-1.
  3. [3]Yin, X.; Yang, R.; Tan, G.; Fan, S., Terrestrial radiative cooling: Using the cold universe as a renewable and sustainable energy source. Science 2020, 370 (6518), 786-791.DOI
  4. [4]Jeong, S. M.; Ahn, J.; Choi, Y. K.; Lim, T.; Seo, K.; Hong, T.; Choi, G. H.; Kim, H.; Lee, B. W.; Park, S. Y.; Ju, S., Development of a wearable infrared shield based on a polyurethane–antimony tin oxide composite fiber. NPG Asia Materials 2020, 12 (1), 32.DOI
  5. [5]Li, Y.; Li, W.; Han, T.; Zheng, X.; Li, J.; Li, B.; Fan, S.; Qiu, C. W., Transforming heat transfer with thermal metamaterials and devices. Nature Reviews Materials 2021, https://doi.org/10.1038/s41578-021-00283-2.
  6. [6]Dyachenko, P. N.; Molesky, S.; Petrov, A. Y.; Störmer, M.; Krekeler, T.; Lang, S.; Ritter, M.; Jacob, Z.; Eich, M., Controlling thermal emission with refractory epsilon-near-zero metamaterials via topological transitions. Nature Communications 2016, 7, 11809.DOI
  7. [7]Inoue, T.; De Zoysa, M.; Asano, T.; Noda, S., Realization of dynamic thermal emission control. Nature Materials 2014, 13 (10), 928.DOI
  8. [8]Xu, J.; Mandal, J.; Raman, A. P., Broadband directional control of thermal emission. Science 2021, 372 (6540), 393-397.
  9. [9]Vassant, S.; Moldovan Doyen, I.; Marquier, F.; Pardo, F.; Gennser, U.; Cavanna, A.; Pelouard, J. L.; Greffet, J. J., Electrical modulation of emissivity. Applied Physics Letters 2013, 102 (8), 081125.DOI
  10. [10]Demiryont, H.; Moorehead, D., Electrochromic emissivity modulator for spacecraft thermal management. Solar Energy Materials and Solar Cells 2009, 93 (12), 2075-2078.DOI
  11. [11]Huang, Z.; Zhou, W.; Tang, X.; Zhu, D.; Luo, F., Effects of substrate roughness on infrared-emissivity characteristics of Au films deposited on Ni alloy. Thin Solid Films 2011, 519 (10), 3100-3106.
  12. [12]Zhao, H.; Hou, L.; Bi, S.; Lu, Y., Enhanced X-band electromagnetic-interference shielding performance of layer-structured fabric-supported polyaniline/cobalt–nickel coatings. ACS Applied Materials & Interfaces 2017, 9 (38), 33059-33070.DOI
  13. [13]Anasori, B.; Gogotsi, Y., 2D metal carbides and nitrides (MXenes): structure, properties and applications. Springer: Berlin, Germany, 2019.DOI
  14. [14]Naguib, M.; Kurtoglu, M.; Presser, V.; Lu, J.; Niu, J.; Heon, M.; Hultman, L.; Gogotsi, Y.; Barsoum, M. W., Two-dimensional nanocrystals produced by exfoliation of Ti₃AlC₂. Advanced Materials 2011, 23 (37), 4248-4253.
  15. [15]Iqbal, A.; Shahzad, F.; Hantanasirisakul, K.; Kim, M.-K.; Kwon, J.; Hong, J.; Kim, H.; Kim, D.; Gogotsi, Y.; Koo, C. M., Anomalous absorption of electromagnetic waves by 2D transition metal carbonitride Ti₃CNTₓ (MXene). Science 2020, 369 (6502), 446-450.
  16. [16]Li, G.; Amer, N.; Hafez, H. A.; Huang, S.; Turchinovich, D.; Mochalin, V. N.; Hegmann, F. A.; Titova, L. V., Dynamical control over terahertz electromagnetic interference shielding with 2D Ti₃C₂Tᵧ MXene by ultrafast optical pulses. Nano Letters 2020, 20 (1), 636-643.
  17. [17]Valourouthu, G.; Maleski, K.; Kurra, N.; Han, M.; Hantanasirisakul, K.; Sarycheva, A.; Gogotsi, Y., Tunable electrochromic behavior of titanium-based MXenes. Nanoscale 2020, 12 (26), 14204-14212.
  18. [18]Han, M.; Liu, Y.; Rakhmanov, R.; Israel, C.; Tajin, M. A. S.; Friedman, G.; Volman, V.; Hoorfar, A.; Dandekar, K. R.; Gogotsi, Y., Solution-processed Ti₃C₂Tₓ MXene antennas for radio-frequency communication. Advanced Materials 2021, 33 (1), 2003225.DOI
  19. [19]Shekhirev, M.; Shuck, C. E.; Sarycheva, A.; Gogotsi, Y., Characterization of MXenes at every step, from their precursors to single flakes and assembled films. Progress in Materials Science 2020, 100757.DOI
  20. [20]Maleski, K.; Shuck, C. E.; Fafarman, A. T.; Gogotsi, Y., The broad chromatic range of two-dimensional transition metal carbides. Advanced Optical Materials 2021, 9 (4), 2001563.DOI
  21. [21]Han, M.; Shuck, C. E.; Rakhmanov, R.; Parchment, D.; Anasori, B.; Koo, C. M.; Friedman, G.; Gogotsi, Y., Beyond Ti₃C₂Tₓ: MXenes for electromagnetic interference shielding. ACS Nano 2020, 14 (4), 5008-5016.
  22. [22]Han, M.; Maleski, K.; Shuck, C. E.; Yang, Y.; Glazar, J. T.; Foucher, A. C.; Hantanasirisakul, K.; Sarycheva, A.; Frey, N. C.; May, S. J.; Shenoy, V. B.; Stach, E. A.; Gogotsi, Y., Tailoring electronic and optical properties of MXenes through forming solid solutions. Journal of the American Chemical Society 2020, 142 (45), 19110-19118.DOI
  23. [23]Li, K.; Chang, T. H.; Li, Z.; Yang, H.; Fu, F.; Li, T.; Ho, J. S.; Chen, P. Y., Biomimetic MXene textures with enhanced light-to-heat conversion for solar steam generation and wearable thermal management. Advanced Energy Materials 2019, 9 (34), 1901687.DOI
  24. [24]Zhao, X.; Wang, L. Y.; Tang, C. Y.; Zha, X. J.; Liu, Y.; Su, B. H.; Ke, K.; Bao, R. Y.; Yang, M. B.; Yang, W., Smart Ti₃C₂Tₓ MXene fabric with fast humidity response and Joule heating for healthcare and medical therapy applications. ACS Nano 2020, 14 (7), 8793-8805.DOI
  25. [25]Ma, Z.; Kang, S.; Ma, J.; Shao, L.; Zhang, Y.; Liu, C.; Wei, A.; Xiang, X.; Wei, L.; Gu, J., Ultraflexible and mechanically strong double-layered aramid nanofiber–Ti₃C₂Tₓ MXene/silver nanowire nanocomposite papers for high-performance electromagnetic interference shielding. ACS Nano 2020, 14 (7), 8368-8382.DOI
  26. [26]Zhang, X.; Wang, X.; Lei, Z.; Wang, L.; Tian, M.; Zhu, S.; Xiao, H.; Tang, X.; Qu, L., Flexible MXene-decorated fabric with interwoven conductive networks for integrated Joule heating, electromagnetic interference shielding, and strain sensing performances. ACS Applied Materials & Interfaces 2020, 12 (12), 14459-14467.DOI
  27. [27]Gogotsi, Y.; Anasori, B., The rise of MXenes. ACS Nano 2019, 13 (8), 8491-8494.
  28. [28]Deysher, G.; Shuck, C. E.; Hantanasirisakul, K.; Frey, N. C.; Foucher, A. C.; Maleski, K.; Sarycheva, A.; Shenoy, V. B.; Stach, E. A.; Anasori, B.; Gogotsi, Y., Synthesis of Mo₄VAlC₄ MAX phase and two-dimensional Mo₄VC₄ MXene with 5 atomic layers of transition metals. ACS Nano 2020, 14 (1), 204-217.
  29. [29]Dahlqvist, M.; Rosen, J., Predictive theoretical screening of phase stability for chemical order and disorder in quaternary 312 and 413 MAX phases. Nanoscale 2020, 12 (2), 785-794.DOI
  30. [30]Abdolhosseinzadeh, S.; Jiang, X.; Zhang, H.; Qiu, J.; Zhang, C. J., Perspectives on solution processing of two-dimensional MXenes. Materials Today 2021, https://doi.org/10.1016/j.mattod.2021.02.010.
  31. [31]Akuzum, B.; Maleski, K.; Anasori, B.; Lelyukh, P.; Alvarez, N. J.; Kumbur, E. C.; Gogotsi, Y., Rheological characteristics of 2D titanium carbide (MXene) dispersions: a guide for processing MXenes. ACS nano 2018, 12 (3), 2685-2694.DOI
  32. [32]Salles, P.; Pinto, D.; Hantanasirisakul, K.; Maleski, K.; Shuck, C. E.; Gogotsi, Y., Electrochromic effect in titanium carbide MXene thin films produced by dip-coating. Advanced Functional Materials 2019, 29 (17), 1809223.
  33. [33]Sarycheva, A.; Gogotsi, Y., Raman spectroscopy analysis of the structure and surface chemistry of Ti₃C₂Tₓ MXene. Chemistry of Materials 2020, 32 (8), 3480-3488.
  34. [34]Uzun, S.; Han, M.; Strobel, C. J.; Hantanasirisakul, K.; Goad, A.; Dion, G.; Gogotsi, Y., Highly conductive and scalable Ti₃C₂Tₓ-coated fabrics for efficient electromagnetic interference shielding. Carbon 2021, 174, 382-389.DOI
  35. [35]Shuck, C. E.; Sarycheva, A.; Anayee, M.; Levitt, A.; Zhu, Y.; Uzun, S.; Balitskiy, V.; Zahorodna, V.; Gogotsi, O.; Gogotsi, Y., Scalable synthesis of Ti₃C₂Tₓ MXene. Advanced Engineering Materials 2020, 22 (3), 1901241.
  36. [36]Han, M.; Gogotsi, Y., Selective infrared thermal emission and stealth properties of MXenes. U.S. Patent., PCT/US2020/063046, Priority December 3, 2020.

Paper details

vlnc:W_rp5draeg
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents