betaFeedback

WorksPhysics and Astronomy

Systematic strain-induced bandgap tuning in binary III-V semiconductors from density functional theory

Abstract

The modification of the nature and size of bandgaps for III-V semiconductors is of strong interest for optoelectronic applications. Strain can be used to systematically tune the bandgap over a wide range of values and induce indirect-to-direct (IDT), direct-to-indirect (DIT), and other changes in bandgap nature. Here, we establish a predictive ab initio approach, based on density functional theory, to analyze the effect of uniaxial, biaxial, and isotropic strain on the bandgap. We show that systematic variation is possible. For GaAs, DITs were observed at 1.52% isotropic compressive strain and 3.52% tensile strain, while for GaP an IDT was found at 2.63% isotropic tensile strain. We additionally propose a strategy for the realization of direct-indirect transition by combining biaxial strain with uniaxial strain. Further transition points were identified for strained GaSb, InP, InAs, and InSb and compared to the elemental semiconductor silicon. Our analyses thus provide a systematic and predictive approach to strain-induced bandgap tuning in binary III-V semiconductors.

III-V_binary_JPCM.arxiv.pdf

Introduction

Semiconductor compounds attract a great amount of attention, both in science and technology, due to their immense application range in areas such as optoelectronics and integrated circuits [1, 2]. One of the major goals in basic and applied research is to tailor the optical properties of semiconductor materials to a target application. The most important fundamental property determining these properties is the material’s bandgap. For example, materials for optical telecommunication applications require direct bandgaps in the range of 0.80–0.95 eV [3, 4, 5], while a range of 0.5–2.0 eV is necessary for materials used in efficient solar cells [6, 7, 8, 9]. One material class that is especially versatile in this respect are compound semiconductors, specifically the III-V semiconductors composed of elements from group 13 and 15 of the periodic table of elements [2, 5, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22]. In the last decades, the optical properties of this material class have been intensively investigated [2, 10, 11, 12, 13, 14, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36] and several strategies have emerged to fine-tune the bandgap. Changing the nature of the chemical elements and their relative composition is a powerful approach to vary the gap over a wide range of energies [37, 38, 39, 40, 41, 42, 43, 44]. However, changing the chemical composition is not always possible. One reason for this lies in the constraints in the growth characteristics of precursor molecules for the chemical vapor deposition techniques often used to grow these materials. Another reason is the thermodynamic instabilities of some elemental compositions [3, 14, 37, 44, 45, 46, 47, 48].

An alternative and sometimes also complementary approach to vary the bandgap is strain engineering. This can be achieved through external effects such as: applying pressure on the system [23, 24, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36], altering the temperature of the system, or changing the substrate in epitaxial growth processes [13, 16, 19, 37, 38, 39, 40, 41, 42, 45, 46, 49, 50, 51, 52, 53, 54, 55, 56, 57, 58, 59, 60, 61, 62]. All of these approaches result in structural strain in the system because of the deviation of one or several lattice parameters of the material from their equilibrium values. The effects on the electronic structure from straining the material are shifts in valence-band maximum (VBM) and conduction-band minimum (CBM), and thus, the variation in the bandgap.

Many attempts have been made to understand the effect of strain from theoretical perspectives. The electronic properties of semiconductor materials have been previously analyzed by: (a) empirical or semi-empirical methods such as the local/nonlocal empirical pseudopotential method [63, 64, 65, 66, 67, 68, 69, 70, 71], the semi-empirical tight-binding method [72, 74, 75, 76, 77, 78, 79, 80, 81, 82, 83, 84] [73], the k⋅pk \cdot p method [85, 86, 87, 88, 89, 90]; or by (b) ab initio methods [91, 92, 93, 94, 95, 96, 97, 98] such as density functional theory (DFT) [91, 99, 100, 101, 102, 103, 104]. Although empirical and semi-empirical methods are computationally efficient and often easy to apply, they rely on many empirical fitting parameters. This strongly lowers their ability to predict properties for new materials, which is a core goal in computational materials design [105]. In contrast, ab initio methods allow the calculation of the electronic structure without the need for empirical fitting parameters.

One of the most widely used ab initio approaches in material science is DFT. The crucial ingredient here is the density functional. Functionals following the generalized gradient approximation (GGA) often lead to an excellent agreement of computed lattice parameters with experimental data. However, they are known to show very large errors for bandgaps [105, 106, 107, 108, 109]. Hybrid functionals such as HSE06 [110] and GW-based methods [95, 96, 97, 98] can solve this issue but are computationally expensive.

[110] and GW-based methods [95, 96, 97, 98] can solve this issue but are computationally expensive. Previously, we and others successfully used the exchange-correlation functional, developed by Tran and Blaha, to predict the electronic properties of unstrained III-V compound semiconductors without empirical adjustments or application of scissor operators [105, 111, 112, 113, 114, 115, 116, 117]. Here, we will show that this approach can also successfully be used for predicting properties by applying a wide range of strains to these materials.

Although strain engineering is an established field for III-V semiconductors [2, 45, 87, 118, 119], the investigation of strain effects has recently found renewed interest in the field of nanowires [120, 121, 122, 123, 124, 125, 126, 127, 128]. Furthermore, no systematic theoretical study is yet available that predicts optical properties of strained materials of this kind without empirical adjustments. We now set out to reliably predict the optical properties of strained materials over a wide range of strains. This will ultimately enable computational materials design approaches in strain engineering of established and upcoming materials.

This work will establish the methodology and highlight the challenges of predictive modelling. Thus, we focus our analysis of strain effects on the electronic structure of the most widely investigated binary III-V semiconductors: GaAs and GaP. These materials are not only interesting for basic research but also support a wide range of applications (either as binary materials or as a host material for multinary compounds) in microelectronics, solar cells, laser technology, and LEDs [2, 3, 4, 5, 6, 7, 8, 9, 14, 15, 16, 17, 18, 19, 20, 21]. To show the general applicability of our approach, selected data on the materials Si, GaSb, InP, InAs, and InSb are included. The ultimate goal is to provide guidelines for future experimental work on strained materials.

Model

SystemSiGaPGaAsGaSbInPInAsInSb
Calculation5.4215.4745.6896.1345.9396.1386.556
Experiment [38, 129]5.4315.4515.6536.0965.8696.0586.479

Table 1. Computed (PBE-D3(BJ)) equilibrium lattice parameters (Å) for the materials investigated in comparison to experimental reference values.

In this study we model uniaxial, biaxial, and isotropic strain. Figure 1 schematically shows which lattice parameters are kept fixed and which are relaxed in the modelling of these three types of strain. The materials investigated all feature zincblende structures. The growth direction in the “theoretical epitaxy” approach applied (see below) was taken to be [1] in this study and was defined as the zz-direction in our modelling approach. We limited our analysis of uniaxial strain to the application of strain along the growth direction only. This uniaxial (compressive) strain is experimentally realized most often by applying pressure. Here, we modelled this by varying the lattice parameter in the zz-direction while relaxing the in-plane lattice parameters (Figure 1a). In the spirit of a systematic study, we also studied uniaxial tensile strain over the same range of values. However, the experimental realization of expanding lattice parameters is typically limited to small strain values (e.g. by increasing the temperature or applying shear stress). The major approach to produce biaxially strained materials is epitaxial growth on a substrate with a different lattice parameter (asa_s). We thus fixed the in-plane lattice parameters (axa_x, aya_y) to the lattice parameter of an (imaginary) substrate (asa_s) while varying the parameter in the growth direction (Figure 1b). In this case, we considered the structural strain imposed by a substrate but neglected the electronic influence for the modelling (theoretical epitaxy) [45, 119]. Isotropic strain is then consequently modelled by not constraining any lattice parameter and increasing (decreasing) all lattice parameters by the same amount (Figure 1c).

Figure 1. The strain models used in this study: (a) uniaxial strain, (b) biaxial strain, and (c) isotropic strain. The blue and red arrows correspond to tensile and compressive strain, respectively. The zz-direction is defined as the strain (a) or growth (b) direction. For the biaxial case, asa_s corresponds to the (epitaxial) substrate lattice parameter.

Computational details

Computations were carried out with DFT-based approaches as implemented in the Vienna Ab initio Simulation Package (VASP 5.4.4) [101, 130, 131, 132, 133], using plane-wave basis sets in conjunction with the projector augmented wave (PAW) method [134, 135]. The primitive zinc blende cell was used throughout. The basis set energy cutoff of 450 eV, the electronic energy convergence criteria of 10−610^{-6} eV, and the force convergence of 10−210^{-2} eV/Å were used. Reciprocal space was sampled with a 10×10×1010 \times10 \times10 Γ-centered Monkhorst-Pack kk-point mesh [136]. Optimizations of the primitive cells were performed using the PBE functional [106] with the semi-empirical dispersion correction scheme DFT-D3 with a Becke-Johnson type damping function [137, 138]. The geometry optimizations were carried out by the consecutive volume and position optimization until convergence was reached. For every set of lattice parameter values investigated, all atomic positions were optimized.

For the bandgap and band structure calculations, the TB09 functional was used [111] including spin-orbit coupling. This had previously been used to give an excellent agreement with the experimental bandgaps for this compound class [105, 111, 112, 113, 114, 115, 116]. The band energies for all the different configurations were re-normalized to the respective VBM. We limited our calculations to a range of ±10% strain by applying constrained optimizations as outlined in the previous section. This is in the order of magnitude of pressures (10 to several 100 GPa) achievable in modern experiments [33, 139, 140, 141, 142, 143, 144, 145, 146, 147, 148, 149, 150]. We indicate tensile strain with a “+” sign to emphasize the positive strain value and to make it easier for the reader to distinguish it from compressive strain values, which are denoted with a “−” sign.

The contribution of the atomic orbitals at the different kk-points on the bands was calculated by projecting the plane waves on the minimal basis set using LOBSTER [151, 152].

Results

Unstrained structures

Before we discuss the influence of strain, the unstrained materials investigated here shall briefly be presented. Regarding the sign convention, we define positive strain to correspond to expansion (tensile strain) and negative strain as compression (compressive strain). The strain values were calculated according to equation (1).

strain⁡(%)=af−aeqmaeqm×100(1)\operatorname{strain}(\%) = \frac{a_f-a_{eqm}}{a_{eqm}} \times100 \tag*{(1)}

Here, afa_f is the lattice parameter in the strained structure while aeqma_{eqm} is the equilibrium lattice parameter. The equilibrium lattice parameters for all materials investigated were computed with the PBE-D3(BJ) approach and are given in table 1. The good agreement with the experimental lattice parameters (maximum deviation of 0.09 Å or 1.3%) lends confidence to the accuracy of the theoretical approach.

Gallium arsenide

Isotropic strain

First, we present the bandgap variation of GaAs under the application of isotropic strain in a range of ±10%\pm10\% around the equilibrium lattice parameter. Figure 2 shows the variation of the energy difference between the conduction band (CB) and the valence band (VB) at the Γ\Gamma point (ΔEΓ\Delta E_{\Gamma}), as well as the bandgap (EgE_{\mathrm{g}}), as a function of strain. Here, and throughout the manuscript, we distinguish between these two energy differences. For a direct bandgap material, both values are the same. If EgE_{\mathrm{g}} is smaller than ΔEΓ\Delta E_{\Gamma} this indicates an indirect bandgap. A strain value where the two curves start deviating thus indicates a direct to indirect (DIT) bandgap transition point.

Isotropic strain effects on the bandgap of GaAs

Figure 2. Isotropic strain effects on the bandgap of GaAs. The energy difference between CB and VB at the Γ\Gamma-point (ΔEΓ\Delta E_{\Gamma}, blue), the bandgap (EgE_{\mathrm{g}}, magenta), the direct to indirect transition (DIT), and the semiconductor to metal transition (SMT) are shown. The solid orange line indicates EgE_{\mathrm{g}} for the equilibrium structure (1.47 eV). The inset shows the region of the DIT with a finer grid of strain calculations.

Under tensile strain, EgE_{\mathrm{g}} decreases until, at +6.78% strain, the bandgap vanishes, corresponding to a semiconductor to metal transition (SMT). In this case, the EgE_{\mathrm{g}} curve coincides with the ΔEΓ\Delta E_{\Gamma} curve throughout, indicating a direct bandgap. Under compressive strain, however, the EgE_{\mathrm{g}} curve initially follows the ΔEΓ\Delta E_{\Gamma} curve until −1.56% strain, where the EgE_{\mathrm{g}} curve then separates from the ΔEΓ\Delta E_{\Gamma} curve. Although ΔEΓ\Delta E_{\Gamma} still increases under further strain, the bandgap starts to decrease. Thus, we have a DIT point here.

To understand the origin of this deviation we looked at the change in CB energies for strained GaAs relative to their values for the equilibrium structure at four high-symmetry points in reciprocal space: Γ\Gamma, L, Δm\Delta_{\mathrm{m}}, and X points (Figure 3). This showed that the CB energies at the Γ\Gamma and L points decrease under tensile strain with a slight increase for Δm\Delta_{\mathrm{m}} and X points. The largest change was found at the Γ\Gamma point,

Variation of CB energies for isotropically strained GaAs

Figure 3. Variation of CB energies for isotropically strained GaAs at the k-points Γ\Gamma (red), L (blue), Δm\Delta_{\mathrm{m}} (purple), and X (olive) relative to their values in the unstrained structure. The band energies at differently strained configurations were rescaled with respect to their corresponding VBM.

followed by L, Δm\Delta_{\mathrm{m}}, and X. As unstrained GaAs is a direct bandgap semiconductor, this signifies that the bandgap remains direct under tensile strain, to begin with. Subsequently, at +6.78% strain, the CBM and VBM become degenerate, which results in the SMT.

For compressive strain, however, the CB energies at the Γ\Gamma and L point increase while a slight decrease was found at the Δm\Delta_m and X points (Figure 3). This resulted in an increase in the direct bandgap for small strain values. Since CB at the Γ\Gamma point changed the most with strain, beyond −1.56%-1.56\% strain it superseded the energy at the L point. This resulted in the CBM shifting from the Γ\Gamma to the L point and a DIT. CB energy at the Γ\Gamma point increased further resulting in a steep increase of ΔEΓ\Delta E_{\Gamma} for high strain values (Figure 2). CB at the L point increased much slower in energy, flattening the EgE_g curve and even producing bandgap decrease at high compressive strain (Figure 2). The band structures computed at each strain value can be found in the supporting information (figures S1a-b).

Further, by comparing the difference in CB energies at the Γ\Gamma, L, Δm\Delta_m, and X points, different ‘transition points’ were estimated (Figure 4). The first transition was from Γ\Gamma to L at −1.56%-1.56\% strain (DIT), the second from L to Δm\Delta_m at −2.28%-2.28\% strain, and the third from Δm\Delta_m to X at −4.47%-4.47\% strain. Increasing the resolution in the k points further revealed that, unlike the sharp first and second transitions, the third was much smoother (figure S1c). During the third transition, the CBM started to flatten out with strain, until at −6.78%-6.78\% when the X point also became part of the CBM-plateau. After that, the plateau started to shrink towards the X point. Note, that the VBM remained at the Γ\Gamma point throughout. Thus, the change in CBM under compressive strain determined the nature of the transitions.

Difference between CB energies at the Γ point and other k-points

Figure 4. The difference between CB energies at the Γ\Gamma point and other k-points P (ΔECB=ECB−P−ECB−Γ\Delta E_{\mathrm{CB}} = E_{\mathrm{CB-P}} - E_{\mathrm{CB-\Gamma}}; with P = Γ\Gamma, L, Δm\Delta_{\mathrm{m}}, and X) for isotropically strained GaAs. Colored areas indicate at which k-point we find the CBM for the given value of compressive strain. The color scheme: Γ\Gamma (red), L (blue), Δm\Delta_{\mathrm{m}} (purple), and X (olive).

Biaxial strain

4.2.2 Biaxial strain The effect of the biaxial strain on the bandgap is shown in Figure 5 (band structures are shown in figures S1d,e). The bandgap decreased under both compressive and tensile strain. During compression, the EgE_g curve coincided with ΔEΓ\Delta E_{\Gamma} throughout. The CBM always remained at the Γ\Gamma point, and hence, the bandgap remained direct. Only for very high compressive strain values (beyond −7.86%-7.86\%), did the CBM and VBM become degenerate, leading to an SMT. For tensile strain, a DIT was found at +3.52%+3.52\% strain, exemplified by the EgE_g curve splitting from ΔEΓ\Delta E_{\Gamma} in Figure 5.

Biaxial strain effects on the bandgap of GaAs

Figure 5. Biaxial strain effects on the bandgap of GaAs. The energy difference between CB and VB at the Γ\Gamma-point (ΔEΓ\Delta E_{\Gamma}, blue), the bandgap (EgE_g, magenta), the direct to indirect transition (DIT), the semiconductor to metal (SMT), and the semiconductor to semimetal (SsMT) transitions are shown. The solid orange line indicates EgE_g for the equilibrium structure (1.47 eV).

Under further tensile strain, the bandgap continued to decrease until GaAs became a semimetal at +8.00%+8.00\% strain. Thus, we observed a semiconductor to semimetal transition (SsMT). By comparing the difference in CB energies at the Γ\Gamma, L, Δm\Delta_m, and X points (Figure 6) we found the DIT to correspond to a Γ\Gamma to Δm\Delta_m transition. No further transition points were found here.

Figure 6. The difference between CB energies at the Γ\Gamma point and other k-points P (ΔECB=ECB−P−ECB−Γ\Delta E_{\mathrm{CB}} = E_{\mathrm{CB-P}} - E_{\mathrm{CB-\Gamma}}, with P = Γ\Gamma, L, Δm\Delta_m, and X) for biaxially strained GaAs. Colored areas indicate at which k-point we find the CBM for the given value of tensile strain. The color scheme: Γ\Gamma (red), L (blue), Δm\Delta_m (purple), and X (olive).

Uniaxial strain

4.2.3 Uniaxial strain The uniaxial strain model in our case is equivalent to the biaxial strain model. This is true because we consider the [1] crystal orientation in the zincblende crystal grown on the [1] surface of another zincblende substrate, and the uniaxial strain is then applied in the <100> direction (Figure 1a). In this configuration, relaxing the lattice parameter in the z-direction at fixed in-plane (xx and yy) lattice parameters (asa_s) is equivalent to fixing it in the z-direction at the value aa, and relaxing the in-plane parameters. For the uniaxial strain in other crystal orientations or directions, this equivalence is not true, because of finite off-diagonal stress tensor elements [118, 153, 154].

Therefore, we used the data from the previous subsection and now present them as a function of the out-of-plane lattice parameter (Figure 7). This is essentially a mirrored version of Figure 5 with a changed scaling of the xx-axis. Now, we found the DIT at −7.30% strain, the SsMT at −15.43% strain, and the SMT at +17.73% strain, respectively.

Uniaxial strain effects on the bandgap of GaAs

Figure 7. Uniaxial strain effects on the bandgap of GaAs. The energy difference between CB and VB at the Γ-point (ΔEΓ\Delta E_{\Gamma}, blue), the bandgap (EgE_{\mathrm{g}}, magenta), the direct to indirect (DIT), the semiconductor to metal (SMT), and the semiconductor to semimetal (SsMT) transitions are shown. The solid orange line indicates EgE_{\mathrm{g}} for the equilibrium structure (1.47 eV).

Combining biaxial and uniaxial strain

Uniaxial and biaxial strain were shown in the previous sections to be useful strategies to tune the bandgap. However, one major goal in tuning the electronic structure is changing the nature of the bandgap. As shown in the previous subsection, this cannot be achieved via biaxial compressive strain, which is one of the most common experimental realizations of strain via epitaxial growth. We will now show that by combining uniaxial and biaxial strain this can in fact be achieved.

In a thought experiment (Figure 8), the desired material (GaAs) is first “grown” epitaxially on a substrate with a smaller lattice constant (e.g., GaP), resulting in compressive biaxial strain (here: −3.78%). Such epitaxial growth would lead to expansion of the zz-lattice parameter. Subsequently, uniaxial compressive strain (e.g., pressure) could be applied along the zz-direction to compress the zz-lattice parameter. We assume that the in-plane lattice parameters would not relax upon compression of the zz-lattice parameter. This is shown more clearly in Figure 9 where we find a DIT point at −3.2% uniaxial strain.

Computational bandgap engineering for GaAs grown on GaP substrate

Figure 8. Computational bandgap engineering for GaAs grown on GaP substrate. The energy difference between CB and VB at the Γ-point (ΔEΓ\Delta E_{\Gamma}, blue for iso and green for bi) and the bandgap (EgE_{\mathrm{g}}, magenta for iso and red for bi) are shown as a function of biaxial (bi) and isotropic (iso) strain.

Figure 9. Change in bandgap as a function of uniaxial compressive strain along z-lattice parameter for GaAs grown on GaP [1] substrate. The energy difference between CB and VB at the Γ-point (ΔEΓ\Delta E_{\Gamma}, blue), the bandgap (EgE_{\mathrm{g}}, magenta), and the direct to indirect (DIT) transition are shown.

Next, we further generalized this strategy. Figure 10 shows the required uniaxial compressive strain for the DIT in biaxial compressively strained GaAs. No transition can be

Variation of required uniaxial compressive strain for the direct to indirect transition in biaxial compressively strained GaAs

Figure 10. Variation of required uniaxial compressive strain for the direct to indirect transition (DIT) in biaxial compressively strained GaAs. 3rd order Birch-Murnaghan equation [155] was used for the strain to pressure conversion. We used reference [156, 157] for the bulk modulus and its first derivative data for the conversion.

achieved for biaxial compressive strain below 1.56%, as both the biaxial and isotropic strain would have the same direct nature of the bandgap (Figure 8).

A similar strategy can be applied for the indirect to direct transition (IDT) in biaxial tensile strained GaAs. In this case, one would need to expand the zz-lattice parameter for the transition. Experimentally, this can be achieved e.g., by thermal expansion. As shown in Figure 11, this, however, is only reasonable for biaxial strain smaller than 4.5%. For higher biaxial strain the large required amount of uniaxial tensile strain can not be achieved by thermal expansion only.

Variation of required uniaxial tensile strain for the indirect to direct transition in biaxial tensile strained GaAs

Figure 11. Variation of required uniaxial tensile strain for the indirect to direct transition (IDT) in biaxial tensile strained GaAs. The temperature increase (ΔT\Delta T) required for the thermal expansion was calculated using the linear thermal expansion coefficient of GaAs (5.73×10−6 ∘C−15.73 \times10^{-6}\ ^\circ\mathrm{C}^{-1} [129]).

Gallium phosphide

Gallium phosphide is an indirect bandgap semiconductor. Next, we demonstrate the application of strain on the bandgap engineering. Figure 12 shows the variation in CB energy for GaP under isotropic strain at the Γ\Gamma, L, Δm\Delta_{\mathrm{m}}, and X points relative to their equilibrium values (band structures are shown in figures S1f,g).

Variation of CB energies for isotropically strained GaP at the k-points Gamma, L, Delta sub m, and X

Figure 12. Variation of CB energies for isotropically strained GaP at the k-points Γ\Gamma (red), L (blue), Δm\Delta_{\mathrm{m}} (purple), and X (olive) relative to their values in the unstrained structure. The band energies at differently strained configurations were rescaled with respect to their corresponding VBM.

For compressive strain, the CB at Γ\Gamma and L point increased in energy, while it decreased at the Δm\Delta_{\mathrm{m}} and X points. As GaP is an indirect bandgap semiconductor at equilibrium, the nature of the bandgap thus did not change. For tensile strain, the CB energy at the Γ\Gamma and L points decreased strongly while we found a small increase at the Δm\Delta_{\mathrm{m}} and X points. This led to a shift of the indirect bandgap from Δm\Delta_{\mathrm{m}} to L at +1.43% tensile strain (Figure 13). As the slope for the energy at the Γ\Gamma point

Difference between CB energies at the Gamma point and other k-points for isotropically strained GaP

Figure 13. The difference between CB energies at the Γ\Gamma point and other k-points P (ΔECB=ECB−P−ECB−Γ\Delta E_{\mathrm{CB}} = E_{\mathrm{CB-P}} - E_{\mathrm{CB-\Gamma}}; with P = Γ\Gamma, L, Δm\Delta_{\mathrm{m}}, and X) for isotropically strained GaP. Colored areas indicate at which k-point we found the CBM for the given value of tensile strain. The color scheme: Γ\Gamma (red), L (blue), Δm\Delta_{\mathrm{m}} (purple), and X (olive).

× No transitions within ±10% strain.

was largest (Figure 12), we found an indirect-to-direct (IDT) transition at +2.63% strain (Figure 13 and Figure S2).

Isotropic strain effects on the bandgap of GaP

Figure S2. Isotropic strain effects on the bandgap of GaP. The energy difference between CB and VB at the Γ\Gamma-point (ΔEΓ\Delta E_{\Gamma}, blue), the bandgap (EgE_{\mathrm{g}}, magenta), and the indirect to direct transition (IDT) are shown. The solid orange line indicates EgE_{\mathrm{g}} for the equilibrium structure (2.36 eV). The inset shows the region of the IDT with a finer grid of strain calculations resulting in higher resolution.

The result for biaxial strain is shown in Figure 14 (band structures are shown in figures S1h,i). Here, we found no change in the nature of the bandgap throughout the entire range of compressive and tensile strain. The bandgap remained indirect throughout. For very high strain values, we found SsMTs at +8.45% and −9.83% strain.

Biaxial strain effects on the bandgap of GaP

Figure 14. Biaxial strain effects on the bandgap of GaP. The energy difference between CB and VB at the Γ\Gamma-point (ΔEΓ\Delta E_{\Gamma}, blue), the bandgap (EgE_g, magenta), and the semiconductor to semimetal (SsMT) transitions are shown. The solid orange line indicates EgE_g for the equilibrium structure (2.36 eV).

The uniaxial conversion of the data in Figure 14, as was explained for GaAs case, wouldn’t have any further special interest (SI Figure S3). Similar to GaAs, by combining biaxial and uniaxial strain in GaP one can in principle achieve IDT. However, this would require large uniaxial tensile strain (> 8%), which can not be realized by thermal expansion (Figure S4).

Uniaxial strain effects on the bandgap of GaP

Figure S3. Uniaxial strain effects on the bandgap of GaP. The energy difference between CB and VB at the Γ\Gamma-point (ΔEΓ\Delta E_{\Gamma}, blue) and the bandgap (EgE_{\mathrm{g}}, magenta) are shown. The solid orange line indicates EgE_{\mathrm{g}} for the equilibrium structure (2.36 eV).

Variation of required uniaxial tensile strain for the indirect to direct transition (IDT) to take place in biaxial tensile strained GaP

Figure S4. Variation of required uniaxial tensile strain for the indirect to direct transition (IDT) to take place in biaxial tensile strained GaP.

Silicon, GaSb, InP, InAs, and InSb

We also applied the approach outlined in detail for GaAs and GaP to other interesting semiconductor materials. Table 2 and 3 summarizes the main results for Si, GaSb, InP, InAs, and InSb. In all cases, the VBM stayed at the Γ\Gamma point throughout the strain regimes applied. Thus, the position of the CBM in reciprocal space determined the nature of the band gap.

SystemType[a]^{[a]}Isotropic (%)Biaxial (%)IsotropicBiaxial
SiIDT+10.31[b]^{[b]}×Δm→L→Γ\Delta_m\to L\to\GammaΔm→K→L\Delta_m\to K\to L
GaPIDT+2.63×Δm→L→Γ\Delta_m\to L\to\GammaΔm→L\Delta_m\to L
GaAsDIT−1.56+3.52Γ→L→Δm→X\Gamma\to L\to\Delta_m\to XΓ→Δm\Gamma\to\Delta_m
GaSbDIT−1.00+3.71Γ→L→Δm\Gamma\to L\to\Delta_mΓ→Δm\Gamma\to\Delta_m
InPDIT−4.40+7.66Γ→X\Gamma\to XΓ→Δm\Gamma\to\Delta_m
InAsDIT−7.41×Γ→X\Gamma\to X×
InSbDIT−5.18×Γ→L→Δm\Gamma\to L\to\Delta_m×

Table 2. Change in the nature of bandgap for different III-V semiconductor materials for isotropic and biaxial strain.

× No transitions within ±10% strain.

Si and GaP are indirect bandgap semiconductors in their equilibrium structure while the other materials discussed show direct bandgaps. Accordingly, Si and GaP showed IDTs while the other materials showed DITs. The strain values where these transitions were found, for isotropic and biaxial strain, are shown in columns 3 and 4 of Table 2. For the isotropic strain case, the IDTs were found for tensile strain as already discussed for GaP in the previous section. The value for Si was so high (+10.31%) that it will certainly be out of range for any experiment. The DITs were found for isotropic compressive strain throughout, with strain values ranging from −1.00% (GaSb) to −7.41% (InAs).

For biaxial strain, DITs were found only for GaAs, GaSb, and InP. In all cases, a significant tensile strain would be necessary. For many materials, transitions were found to other k-points in reciprocal space where the nature of the bandgap stayed indirect. This is shown in the right-hand part of the table. [more details are shown in figures S5 and S6.] Notably, In-based compound semiconductors showed the DIT points at much higher strain values compared to Ga-based materials. Figure 15 shows the contribution of the atomic orbitals to the CB for GaAs and InAs. At the decisive points in k-space (Γ\Gamma, LL, and XX points) the group III elements showed the major contributions to CB, explaining the bandgap dependency on the group III element. Furthermore, the nature of the orbital contribution changes in k-space. While the Ga(4s) and In(5s) orbitals dominate at the Γ\Gamma point, the LL point and the XX point showed high contributions from the Ga(4p) and In(5p) orbitals. The energy gap between 5s and 5p orbital in In is much higher than 4s and 4p in Ga.

Atom resolved orbital contributions for GaAs and InAs CB

Figure 15. Atom resolved orbital contributions for GaAs and InAs CB. Solid sky blue: Ga(4s), dotted sky blue: In(5s), solid orange: Ga(4p), dotted orange: In(5p), solid green: As(4s) in GaAs, dotted green: As(4s) in InAs, solid red: As(4p) in GaAs, dotted red: As(4p) in InAs.

[a]^{[a]} Experimental bandgaps are at 300 K [38, 129].

[b]^{[b]} Reference [28].

[c]^{[c]} Reference [28, 157, 158].

— For Si and GaP IDTs are in the tensile strain region. No experimental data available.

Therefore, changing group III from Ga to In increased the relative energy difference in Γ\Gamma–X and Γ\Gamma–L, Figure 16. Under strain, the decrease of these relative energy differences ultimately resulted in the shift of CBM from the Γ\Gamma to the L and/or X point (SI section S-VI). Therefore, the higher this relative energy difference, the higher the requirement of the amount of strain needed to reach the DIT point.

Relative energy differences in Γ–X and Γ–L at the CB for Ga and In series binaries

Figure 16. The relative energy differences in Γ\Gamma–XX (olive) and Γ\Gamma–LL (blue) at the CB for Ga and In series binaries.

Table 3 summarizes the SMTs and SsMTs for the compound semiconductors investigated. These transitions depend on the closing of the CBM and VBM gaps. As the VBM always remains at the Γ\Gamma point, these transition points therefore depend on ΔEΓ\Delta E_{\Gamma}. Figure 17 shows the SMTs under isotropic strain for different systems in relation to their corresponding ΔEΓ\Delta E_{\Gamma}. As the ΔEΓ\Delta E_{\Gamma} increased, so did the S(s)MTs.

SystemΔEΓ\Delta E_{\Gamma} (eV)SMT Isotropic (%)SMT Biaxial (%)SsMT Isotropic (%)SsMT Biaxial (%)
Si3.14+15.001××+3.70, −6.50
GaP2.99+13.001××+8.45, −9.83
GaAs1.81+6.67−7.86×+8.00
GaSb0.64+2.85−5.00×+5.07
InP1.43+8.20−9.90×+10.38
InAs0.36+2.10+4.74, −4.36××
InSb0.03+0.34+0.34, −0.34××

Table 3. Semiconductor to metal transition (SMT) and semiconductor to semimetal transition (SsMT) points for different III-V semiconductor materials under isotropic and biaxial strain. ΔEΓ\Delta E_{\Gamma} corresponds to the energy difference between CB and VB at the Γ\Gamma point.

Correlation between SMT isotropic strain and the energy difference between CB and VB at the Γ-point

Figure 17. Correlation between SMT (isotropic strain) and the energy difference between CB and VB at the Γ\Gamma-point (ΔEΓ\Delta E_{\Gamma}) for Ga and In series binaries.

In table 4 we compared our calculated results with the available experimental findings. The results match quite well. In experiments, the DIT points were measured in terms of applied hydrostatic pressure. Using the third-order Birch-Murnaghan equation [155] we converted the measurement in terms of strains. We used reference [156, 157] for the bulk modulus and and its first derivative data for the conversion. For GaAs, the strain region when CBM was visible at the L point was very small (only 0.72 % strain window), Figure 4. Therefore, we conclude that in the experiment this region was most likely missed (Table 4, 3rd row last column). For InSb a deviation of 0.14 eV was found for the equilibrium bandgap. This, in turn, would result in the overestimation of the DIT point in our calculation (Table 4).

SystemEquilibrium bandgap (eV)Isotropic strain DIT (%)Transitions
CalculatedExperiment[a]^{[a]}CalculatedExperimentCalculatedExperiment
Si1.191.12————
GaP2.362.26————
GaAs1.471.42−1.56−2.10[b]^{[b]}Γ→L\Gamma\to\mathrm{L}Γ→X[b]\Gamma\to\mathrm{X}^{[b]}
GaSb0.640.73−1.00−0.70[b]^{[b]}Γ→L\Gamma\to\mathrm{L}Γ→L[b]\Gamma\to\mathrm{L}^{[b]}
InP1.431.34−4.40−3.51[c]^{[c]}Γ→X\Gamma\to\mathrm{X}Γ→X[c]\Gamma\to\mathrm{X}^{[c]}
InAs0.360.35−7.41−6.84[c]^{[c]}Γ→X\Gamma\to\mathrm{X}Γ→X[c]\Gamma\to\mathrm{X}^{[c]}
InSb0.030.17−5.18−3.09[c]^{[c]}Γ→L\Gamma\to\mathrm{L}Γ→X[c]\Gamma\to\mathrm{X}^{[c]}

Table 4. The calculated equilibrium bandgaps, DIT points, and the DIT transitions compared with the experiments.

Conclusions

We calculated the strain-induced bandgap variation for various III-V binary compounds focusing on GaAs and GaP for a detailed analysis. We investigated compressive and tensile strain in the range of ±10%\pm10\% around the equilibrium structure, which enabled the tuning of the bandgap over a wide range. Furthermore, we showed the presence of direct-to-indirect and indirect-to-direct transitions in the nature of bandgap of these materials based on the analyses of differences between valence and conduction band energies at the Γ\Gamma-point (ΔEΓ\Delta E_{\Gamma}) and the bandgap (EgE_{\mathrm{g}}). Only 4 special k-points were found to be responsible for the direct-indirect transitions: Γ\Gamma, L, Δm\Delta_{\mathrm{m}}, and X. The valence band maximum stayed at the Γ\Gamma point throughout the strain regimes applied. Thus, the position of the conduction band minimum alone in reciprocal space determined the nature of the band gap. By combining the biaxial and uniaxial strain, we proposed a strategy for the realization of direct-indirect transitions in the regions where otherwise no transition could be achieved by single type of strain. With this work, we laid the foundation for further efforts with multinary compound semiconductors under strain.

Data availability statement

All the density functional theory calculations data are available in the NOMAD repository (DOI: https://doi.org/10.17172/NOMAD/2022.08.20-2).

Acknowledgments

We thank the German Research Foundation (DFG) for funding via the Research Training Group “Functionalization of Semiconductors” (GRK 1782). We acknowledge computational resources provided by HRZ Marburg, GOETHE-CSC Frankfurt, ZIH Dresden & HLR Stuttgart. We thank Prof. Kerstin Volz for discussions and continued support.

ORCID iDs

Badal Mondal https://orcid.org/0000-0002-0522-1254

Ralf Tonner-Zech https://orcid.org/0000-0002-6759-8559

Movies

The movies referenced here show the evolution of band structure in GaAs and GaP under different strain regimes. The band structures were calculated along the high symmetry path of zincblende structures. In all cases, the band energies were rescaled with respect to their corresponding VBM.

fig:S1a: GaAs under isotropic tensile strain

fig:S1b: GaAs under isotropic compressive strain

fig:S1c: GaAs under isotropic compressive strain zoomed in CB region

fig:S1d: GaAs under biaxial tensile strain

fig:S1e: GaAs under biaxial compressive strain

fig:S1f: GaP under isotropic tensile strain

fig:S1g: GaP under isotropic compressive strain

fig:S1h: GaP under biaxial tensile strain

fig:S1i : GaP under biaxial compressive strain

Indirect-to-direct (IDT) transition in GaP

Uniaxial strain effect on bandgap of GaP

Indirect-to-direct (IDT) transition in GaP by combining biaxial and uniaxial strain

Bandgap variation with strain for III–V semiconductors

Figure a. Si

Figure S5. Bandgap variation with strain for different III-V binary semiconductors. The energy difference between conduction and valence band at the Γ\Gamma point (ΔE(Γ)\Delta E(\Gamma), magenta for iso and green for bi) and the bandgap (EgE_{\mathrm{g}}, blue for iso and red for bi) are shown as a function of biaxial (bi) and isotropic (iso) strain. The solid orange lines indicate EgE_{\mathrm{g}} for the equilibrium structures.

CBM transition path for Si

(a) Si

(b) GaP

(c) GaAs

(d) InP

(e) InAs

Figure 18 (PDF p. 22). S VI CBM transition path for different III–V semiconductors

Figure S6. The difference between conduction energies at the Γ\Gamma point and other kk points P (ΔECB=ECB−P−ECB−Γ\Delta E_{\mathrm{CB}} = E_{\mathrm{CB-P}} - E_{\mathrm{CB-\Gamma}}; with P = L, Δm\Delta_m, and X) for isotropically strained III-V binary semiconductors. The enclosed areas between the lines and the x-axis indicate at which k-point we find the conduction band minima for the given values of strains.

(a)

InP plot

(b)

GaSb plot

(c)

Figure S7. The difference between conduction energies at the Γ\Gamma point and other kk points P (ΔECB=ECB−P−ECB−Γ\Delta E_{\mathrm{CB}} = E_{\mathrm{CB-P}} - E_{\mathrm{CB-\Gamma}}; with P = Γ\Gamma, L, Δm\Delta_m, and X) for biaxially strained III-V binary semiconductors. The enclosed areas between the lines and the x-axis indicate at which k-point we find the conduction band minima for the given values of strains.

References

  1. [1]Soref R A 1993 Silicon-based optoelectronics Proc. IEEE 81 1687–706
  2. [2]Yu P Y and Cardona M 2010 Fundamentals of Semiconductors (Berlin, Heidelberg: Springer Berlin Heidelberg)
  3. [3]Hepp T, Lehr J, Günkel R, Maßmeyer O, Glowatzki J, Ruiz Perez A, Reinhard S, Stolz W and Volz K 2022 Room-temperature laser operation of a (Ga,In)As/Ga(As,Bi)/(Ga,In)As W-type laser diode Electron. Lett. 58 70–2
  4. [4]Fuchs C, Brüggemann A, Weseloh M J, Berger C, Möller C, Reinhard S, Hader J, Moloney J V, Bäümner A, Koch S W and Stolz W 2018 High-temperature operation of electrical injection type-II (GaIn)As/Ga(AsSb)/(GaIn)As “W”-quantum well lasers emitting at 1.3 μm Sci. Rep. 8 1422
  5. [5]Mokkapati S and Jagadish C 2009 III-V compound SC for optoelectronic devices Mater. Today 12 22–32
  6. [6]Dimroth F, Tibbitts T N D, Niemeyer M, Predan F, Beutel P, Karcher C, Oliva E, Siefer G, Lackner D, Fus-Kailuweit P, Bett A W, Krause R, Drazek C, Guiot E, Wasselin J, Tauzin A and Signamarcheix T 2016 Four-Junction Wafer-Bonded Concentrator Solar Cells IEEE J. Photovoltaics 6 343–9
  7. [7]Létay G and Bett A 2001 EtaOpt–a program for calculating limiting efficiency and optimum bandgap structure for multi-bandgap solar cells and TPV cells, in Proceedings of the 17th European Photovoltaic Solar Energy Conference (2001), 178–181
  8. [8]Mitchell B, Peharz G, Siefer G, Peters M, Gandy T, Goldschmidt J C, Benick J, Glunz S W, Bett A W and Dimroth F 2011 Four-junction spectral beam-splitting photovoltaic receiver with high optical efficiency Prog. Photovoltaics Res. Appl. 19 61–72
  9. [9]Phillipps S P, Dimroth F and Bett A W 2018 High-Efficiency III–V Multijunction Solar Cells McEvoy’s Handbook of Photovoltaics ed S A Kalogirou (Elsevier) pp 439–72
  10. [10]Kneissl M, Seong T-Y, Han J and Amano H 2019 The emergence and prospects of deep-ultraviolet light-emitting diode technologies Nat. Photonics 13 233–44
  11. [11]Asif Khan M, Bhattarai A, Kuznia J N and Olson D T 1993 High electron mobility transistor based on a GaN-AlxGa1−xN heterojunction Appl. Phys. Lett. 63 1214–5
  12. [12]Wu J, Chen S, Seeds A and Liu H 2015 Quantum dot optoelectronic devices: lasers, photodetectors and solar cells J. Phys. D. Appl. Phys. 48 363001
  13. [13]Nakamura S, Mukai T and Senoh M 1991 High-Power GaN P-N Junction Blue-Light-Emitting Diodes Jpn. J. Appl. Phys. 30 L1998–2001
  14. [14]Park J-S, Tang M, Chen S and Liu H 2020 Heteroepitaxial Growth of III-V Semiconductors on Silicon Crystals 10 1163
  15. [15]Bett A W, Dimroth F, Stollwerck G and Sulima O V 1999 III-V compounds for solar cell applications Appl. Phys. A Mater. Sci. Process. 69 119–29
  16. [16]Zimmermann H 2000 III–V Semiconductor Materials on Silicon Integrated Silicon Optoelectronics (Berlin, Heidelberg: Springer Berlin Heidelberg) pp 167–85
  17. [17]Stillman G E, Robbins V M and Tabatabaie N 1984 III-V compound semiconductor devices: Optical detectors IEEE Trans. Electron Devices 31 1643–55
  18. [18]Shah N J and Pei S-S 1989 III-V Device Technologies for Electronic Applications AT&T Tech. J. 68 19–28
  19. [19]Kuech T F 2016 III-V compound semiconductors: Growth and structures Prog. Cryst. Growth Charact. Mater. 62 352–70
  20. [20]Yu E T and Manasreh M O 2002 III-V Nitride Semiconductors: Applications and Devices (Taylor & Francis)
  21. [21]Cheng K Y 2020 III–V Compound Semiconductors and Devices (Cham: Springer International Publishing)
  22. [22]Kosten E D, Atwater J H, Parsons J, Polman A and Atwater H A 2013 Highly efficient GaAs solar cells by limiting light emission angle Light Sci. Appl. 2 e45–e45
  23. [23]Goni A R, Strössner K, Syassen K and Cardona M 1987 Pressure dependence of direct and indirect optical absorption in GaAs Phys. Rev. B 36 1581
  24. [24]Tsay Y-F and Bendow B 1976 Pressure dependence of the direct energy gap of GaAs Phys. Rev. B 14 2681–2
  25. [25]Jayaram A, Kosicki B B and Irvin J C 1968 Δ1 Conduction-Band Minimum of Ge from High-Pressure Studies on p-n Junctions Phys. Rev. 171 836
  26. [26]Müller H, Trommer R, Cardona M and Vogl P 1980 Pressure dependence of the direct absorption edge of InP Phys. Rev. B 21 4879DOI
  27. [27]Welber B, Kim C K, Cardona M and Rodriguez S 1975 Dependence of the indirect energy gap of silicon on hydrostatic pressure Solid State Commun. 17 1021DOI
  28. [28]Edwards A L and Drickamer H G 1961 Effect of Pressure on the Absorption Edges of Some III-V, II-VI, and I-VII Compounds Phys. Rev. 122 1149–57DOI
  29. [29]Strössner K, Ves S, Kim C K and Cardona M 1987 Pressure dependence of the lowest direct absorption edge of ZnTe Solid State Commun. 61 275DOI
  30. [30]Zallen R and Paul W 1964 Band Structure of Gallium Phosphide from Optical Experiments at High Pressure Phys. Rev. 134 A1628–41DOI
  31. [31]Grivickas P, McCluskey M D and Gupta Y M 2007 Indirect band-gap transitions in GaP shocked along the [100], [110], and [111] axes Phys. Rev. B 75 235207DOI
  32. [32]Grivickas P, McCluskey M D and Gupta Y M 2008 Band-gap luminescence of GaP:S shock compressed to 5GPa Appl. Phys. Lett. 92 142104DOI
  33. [33]Paul W 1998 High Pressure in Semiconductor Physics Semiconductors and Semimetals vol 54, ed T Suski and W Paul (Elsevier) pp 1–48
  34. [34]Yu P Y and Welber B 1978 High pressure photoluminescence and resonant Raman study of GaAs Solid State Commun. 25 209–11
  35. [35]Olego D, Cardona M and Müller H 1980 Photoluminescence in heavily doped GaAs. II. Hydrostatic pressure dependence Phys. Rev. B 22 894–903DOI
  36. [36]Welber B, Cardona M, Kim C K and Rodriguez S 1975 Dependence of the direct energy gap of GaAs on hydrostatic pressure Phys. Rev. B 12 5729–38DOI
  37. [37]Beyer A, Stolz W, Volz K, Wegele T, Beyer A, Ludewig P and Rosenow P 2016 Metastable cubic zinc-blende III/V semiconductors : Growth and structural characteristics Prog. Cryst. Growth Charact. Mater. 61 46–62
  38. [38]Vurgaftman I, Meyer J R and Ram-Mohan L R 2001 Band parameters for III-V compound semiconductors and their alloys J. Appl. Phys. 89, 5815.
  39. [39]Stringfellow G B 2019 Fundamental Aspects of MOVPE Metalorganic Vapor Phase Epitaxy (MOVPE) (Wiley) pp 19–69
  40. [40]Volz K, Koch J, Höhndorf F, Kunert B and Stolz W 2009 MOVPE growth of dilute nitride III/V semiconductors using all liquid metalorganic precursors J. Cryst. Growth 311 2418–26
  41. [41]Feifel M, Ohlmann J, Benick J, Rachow T, Janz S, Hermle M, Dimroth F, Belz J, Beyer A, Volz K and Lackner D 2017 MOVPE Grown Gallium Phosphide–Silicon Heterojunction Solar Cells IEEE J. Photovoltaics 7 502–7
  42. [42]Kunert B, Koch J, Torunski T, Volz K and Stolz W 2004 MOVPE growth experiments of the novel (GaIn)N/GaP material system J. Cryst. Growth 272 753–9
  43. [43]Volz K, Torunski T, Kunert B, Rubel O, Nau S, Reinhard S and Stolz W 2004 Specific structural and compositional properties of (GaIn)(NAs) and their influence on optoelectronic device performance J. Cryst. Growth 272 739–47
  44. [44]Veletas J, Hepp T, Volz K and Chatterjee S 2019 Bismuth surface segregation and disorder analysis of quaternary (Ga,In)(As,Bi)/InP alloys J. Appl. Phys. 126 135705
  45. [45]Wegele T, Beyer A, Ludewig P, Rosenow P, Duschek L, Jandieri K, Tonner R, Stolz W and Volz K 2016 Interface morphology and composition of Ga(NAsP) quantum well structures for monolithically integrated LASERs on silicon substrates J. Phys. D: Appl. Phys. 49 075108
  46. [46]Hepp T, Nattermann L and Volz K 2019 MOVPE Growth and Device Applications of Ternary and Quaternary Dilute Bismide Alloys on GaAs Substrates Bismuth-Containing Alloys and Nanostructures ed S Wang and P Lu (Singapur: Springer) pp 37–58
  47. [47]Beyer A, Knaub N, Rosenow P, Jandieri K, Ludewig P, Bannow L, Koch S W, Tonner R and Volz K 2017 Local Bi ordering in MOVPE grown Ga(As,Bi) investigated by high resolution scanning transmission electron microscopy Appl. Mater. Today 6 22–8
  48. [48]Kükelhan P, Firoozabadi S, Beyer A, Duschek L, Fuchs C, Oeierich J O, Stolz W and Volz K 2019 Segregation at interfaces in (GaIn)As/Ga(AsSb)/(GaIn)As- quantum well heterostructures explored by atomic resolution STEM J. Cryst. Growth 524 125180
  49. [49]Volz K, Beyer A, Witte W, Ohlmann J, Németh I, Kunert B and Stolz W 2011 GaP-nucleation on exact Si (001) substrates for III/V device integration J. Cryst. Growth 315 37–47
  50. [50]Cho A Y 1983 Growth of III–V semiconductors by molecular beam epitaxy and their properties Thin Solid Films 100 291–317
  51. [51]Dupuis R D 1997 Epitaxial growth of III–V nitride semiconductors by metalorganic chemical vapor deposition J. Cryst. Growth 178 56–73
  52. [52]Dupuis R D 1984 Metalorganic Chemical Vapor Deposition of III-V Semiconductors Science 226 623–9
  53. [53]Stringfellow G B 1978 VPE Growth of III/V Semiconductors Annu. Rev. Mater. Sci. 8 73–98
  54. [54]Dupuis R D 2000 III-V semiconductor heterojunction devices grown by metalorganic chemical vapor deposition IEEE J. Sel. Top. Quantum Electron. 6 1040–50
  55. [55]Stringfellow G B 2017 Thermodynamic considerations for epitaxial growth of III/V alloys J. Cryst. Growth 468 11–6
  56. [56]Behet M, Hövel R, Kohl A, Küsters A M, Opitz B and Heime K 1996 MOVPE growth of III–V compounds for optoelectronic and electronic applications Microelectronics J. 27 297–334
  57. [57]Volz K, Stolz W, Dadgar A and Krost A 2015 Growth of III/Vs on Silicon Handbook of Crystal Growth (Elsevier) pp 1249–300
  58. [58]Ludewig P, Reinhard S, Jandieri K, Wegele T, Beyer A, Tapfer L, Volz K and Stolz W 2016 MOVPE growth studies of Ga(NAsP)/(BΓa)(AsP) multi quantum well heterostructures (MQWH) for the monolithic integration of laser structures on (001) Si-substrates J. Cryst. Growth 438 63–9
  59. [59]Németh I, Kunert B, Stolz W and Volz K 2008 Heteroepitaxy of GaP on Si: Correlation of morphology, anti-phase-domain structure and MOVPE growth conditions J. Cryst. Growth 310 1595–601
  60. [60]Liebich S, Zimprich M, Beyer A, Lange C, Franzbach D J, Chatterjee S, Hossain N, Sweeney S J, Volz K, Kunert B and Stolz W 2011 Laser operation of Ga(NAsP) lattice-matched to (001) silicon substrate Appl. Phys. Lett. 99 071109
  61. [61]Volk M and Stolz W 2017 Determination of refractive index and direct bandgap of lattice matched BGaP and (BΓa)(AsP) materials on exact oriented silicon J. Appl. Phys. 122 235702
  62. [62]Supplie O, Romanyuk O, Koppka C, Steidl M, Nägelein A, Paszuk A, Winterfeld L, Dobrich A, Kleinschmidt P, Runge E and Hannappel T 2018 Metalorganic vapor phase epitaxy of III–V-on-silicon: Experiment and theory Prog. Cryst. Growth Charact. Mater. 64 103–32
  63. [63]Chelikowsky J R and Cohen M L 1976 Nonlocal pseudopotential calculations for the electronic structure of eleven diamond and zinc-blende semiconductors Phys. Rev. B 14 556–82
  64. [64]Xiao Z, Goldsman N and Dhar N K 2015 Simulation of Indirect-Direct transformation phenomenon of germanium under uniaxial and biaxial strain along arbitrary orientations 2015 International Conference on Simulation of Semiconductor Processes and Devices (SISPAD) (IEEE) pp 397–400
  65. [65]Fischetti M V. and Laux S E 1996 Band structure, deformation potentials, and carrier mobility in strained Si, Ge, and SiGe alloys J. Appl. Phys. 80 2234–52
  66. [66]Cohen M L and Bergstresser T K 1966 Band structures and pseudopotential form factors for fourteen semiconductors of the diamond and zinc-blende structures Phys. Rev. 141 789–96
  67. [67]Gonzalez S, Vasileska D and Demkov A A 2002 Empirical pseudopotential method for the band structure calculation of strained-silicon germanium materials J. Comput. Electron. 1 179–83
  68. [68]Kim J and Fischetti M V. 2010 Electronic band structure calculations for biaxially strained Si, Ge, and III–V semiconductors J. Appl. Phys. 108 013710
  69. [69]Tsay Y F, Gong B, Mitra S S and Vetelino J F 1972 Temperature Dependence of Energy Gaps of Some III-V Semiconductors Phys. Rev. B 6 2330–6
  70. [70]Bechiri A, Benmakhlouf F and Bouarissa N 2003 Band structure of III–V ternary semiconductor alloys beyond the VCA Mater. Chem. Phys. 77 507–10
  71. [71]Cohen M L and Chelikowsky J R 1988 Electronic Structure and Optical Properties of Semiconductors vol 75 (Berlin, Heidelberg: Springer Berlin Heidelberg)
  72. [72]Boykin T B, Klimeck G, Bowen R C and Lake R 1997 Effective-mass reproducibility of the nearest-neighbor models: Analytic results Phys. Rev. B 56 Anderson N G and Jones S D 1991 Optimized tight-binding valence bands and heterojunction offsets in strained III-V semiconductors J. Appl. Phys. 70 4342–56
  73. [74]Boykin T B, Klimeck G and Oyafuso F 2004 Valence band effective-mass expressions in the sp3d5s* empirical tight-binding model applied to a Si and Ge parametrization Phys. Rev. B 69 115201
  74. [75]Tan Y, Povolotskiy M, Kubis T, Boykin T B and Klimeck G 2016 Transferable tight-binding model for strained group IV and III-V materials and heterostructures Phys. Rev. B 94 045311
  75. [76]Nestoklon M O, Benchamekh R and Voisin P 2016 Virtual crystal description of III–V semiconductor alloys in the tight binding approach J. Phys. Condens. Matter 28 305801
  76. [77]Slater J C and Koster G F 1954 Simplified LCAO method for the periodic potential problem Phys. Rev. 94 1498–524
  77. [78]Harrison W A 1989 Electronic structure and the properties of solids : the physics of the chemical bond (New York: Dover Publications)
  78. [79]Chadi D J and Cohen M L 1975 Tight-binding calculations of the valence bands of diamond and zincblende crystals Phys. status solidi 68 405–19
  79. [80]Vogl P, Hjalmarson H P and Dow J D 1983 A Semi-empirical tight-binding theory of the electronic structure of semiconductors J. Phys. Chem. Solids 44 365–78
  80. [81]Jancu J M, Scholz R, Beltram F and Bassani F 1998 Empirical tight-binding calculation for cubic semiconductors: General method and material parameters Phys. Rev. B 57 6493–507
  81. [82]Gürel H H, Akinci Ö and Ünlü H 2006 Semiempirical tight-binding modelling of III-N-based heterostructures Superlattices Microstruct. 40 588–97
  82. [83]Klimeck G, Bowen R C, Boykin T B, Salazar-Lazaro C, Cwik T A and Stoica A 2000 Si tight-binding parameters from genetic algorithm fitting Superlattices Microstruct. 27 77–88
  83. [84]Boykin T B, Klimeck G, Bowen R C and Oyafuso F 2002 Diagonal parameter shifts due to nearest-neighbor displacements in empirical tight-binding theory Phys. Rev. B 66 125207–6
  84. [85]Cavassilas N, Aniel F, Boudjaria K and Fishman G 2001 Energy-band structure of GaAs and Si: A sp* k·p method Phys. Rev. B 64 1152071–5
  85. [86]Cardona M and Pollak F H 1966 Energy-Band Structure of Germanium and Silicon: The k·p Method Phys. Rev. 142 530–43
  86. [87]Bir G L and Pikus G E 1974 Symmetry and strain-induced effects in semiconductors (New York: John Wiley & Sons)
  87. [88]Chuang S L and Chang C S 1996 k·p method for strained wurtzite semiconductors Phys. Rev. B 54 2491–504
  88. [89]Luttinger J M and Kohn W 1955 Motion of Electrons and Holes in Perturbed Periodic Fields Phys. Rev. 97 869–83
  89. [90]Luttinger J M 1956 Quantum theory of cyclotron resonance in semiconductors: General theory Phys. Rev. 102 1030–41
  90. [91]Hohenberg P and Kohn W 1964 Inhomogeneous Electron Gas Phys. Rev. 136 B864–71
  91. [92]Car R and Parrinello M 1985 Unified Approach for Molecular Dynamics and Density-Functional Theory Phys. Rev. Lett. 55 2471–4
  92. [93]Georges A, Kotliar G, Krauth W and Rozenberg M J 1996 Dynamical mean-field theory of strongly correlated fermion systems and the limit of infinite dimensions Rev. Mod. Phys. 68 13–125
  93. [94]Hedin L and Lundqvist S 1969 Solid state physics vol 23, ed H Ehrenreich and F T D Seitz (New York: Academic Press)
  94. [95]Hybertsen M S and Louie S G 1986 Electron correlation in semiconductors and insulators: Band gaps and quasiparticle energies Phys. Rev. B 34 5390–413
  95. [96]Hedin L 1965 New Method for Calculating the One-Particle Green’s Function with Application to the Electron-Gas Problem Phys. Rev. 139 A796–823
  96. [97]Aulbur W G, Jönsson L and Wilkins J W 2000 Quasiparticle Calculations in Solids Solid State Physics vol 54, ed H Ehrenreich and F Spaepen (Academic Press) pp 1–218
  97. [98]Aryasetiawan F and Gunnarsson O 1998 The GW method Reports Prog. Phys. 61 237–312
  98. [99]Kohn W and Sham L J 1965 Self-Consistent Equations Including Exchange and Correlation Effects Phys. Rev. 140 A1133
  99. [100]Kohn W, Becke A D and Parr R G 1996 Density Functional Theory of Electronic Structure J. Phys. Chem. 100 12974
  100. [101]Hafner J 2008 Ab-initio simulations of materials using VASP: Density-functional theory and beyond J. Comput. Chem. 29 2044–78
  101. [102]Hafner J, Wolverton C and Ceder G 2006 Toward computational materials design: the impact of density functional theory on materials research MRS Bull. 31 659–68
  102. [103]Van Doren V E, Van Alsenoy C and Geerlings P 2001 Density functional theory and its application to materials ed V E Van Doren, C Van Alsenoy and P Geerlings (American Institute of Physics)
  103. [104]Fiolhais C, Nogueira F and Marques M A L 2003 A Primer in Density Functional Theory vol 620, ed C Fiolhais, F Nogueira and M A L Marques (Berlin, Heidelberg: Springer Berlin Heidelberg)
  104. [105]Rosenow P, Bannow L C, Fischer E W, Stolz W, Volz K, Koch S W and Tonner R 2018 Ab initio calculations of the concentration dependent band gap reduction in dilute nitrides Phys. Rev. B 97 075201
  105. [106]Perdew J P, Burke K and Ernzerhof M 1996 Generalized Gradient Approximation Made Simple Phys. Rev. Lett. 77 3865–8
  106. [107]Perdew J P and Wang Y 1992 Accurate and simple analytic representation of the electron-gas correlation energy Phys. Rev. B 45 13244–9
  107. [108]Perdew J P 1985 Density functional theory and the band gap problem Int. J. Quantum Chem. 28 497–523
  108. [109]Koller D, Tran F and Blaha P 2011 Merits and limits of the modified Becke-Johnson exchange potential Phys. Rev. B 83 195134
  109. [110]Krukau A V, Vydrov O A, Izmaylov A F and Scuseria G E 2006 Influence of the exchange screening parameter on the performance of screened hybrid functionals J. Chem. Phys. 125 224106
  110. [111]Tran F and Blaha P 2009 Accurate Band Gaps of Semiconductors and Insulators with a Semilocal Exchange-Correlation Potential Phys. Rev. Lett. 102 226401
  111. [112]Kim Y S, Marsman M, Kresse G, Tran F and Blaha P 2010 Towards efficient band structure and effective mass calculations for III-V direct band-gap semiconductors Phys. Rev. B 82 205212
  112. [113]Jiang H 2013 Band gaps from the Tran-Blaha modified Becke-Johnson approach: A systematic investigation J. Chem. Phys. 138 134115
  113. [114]Bannow L C, Rosenow P, Springer P, Fischer E W, Hader J, Moloney J V., Tonner R and Koch S W 2017 An ab initio based approach to optical properties of semiconductor heterostructures Model. Simul. Mater. Sci. Eng. 25 065001
  114. [115]Rehman G, Shafiq M, Saifullah, Ahmad R, Jalali-Asadabadi S, Maqbool M, Khan I, Rahnamaye-Aliabad H and Ahmad I 2016 Electronic Band Structures of the Highly Desirable III–V Semiconductors: TB-mBJ DFT Studies J. Electron. Mater. 45 3314–23
  115. [116]Koller D, Tran F and Blaha P 2012 Improving the modified Becke-Johnson exchange potential Phys. Rev. B 85 155109
  116. [117]Ziane M I, Bensaad Z, Labdelli B and Bennacer H 2014 First-principles study of structural, electronic and optical properties of III-arsenide binary GaAs and InAs, and III-nitrides binary GaN and InN: Improved density-functional-theory Study Sensors & transducers 27 374
  117. [118]Sun Y, Thompson S E and Nishida T 2007 Physics of strain effects in semiconductors and metal-oxide-semiconductor field-effect transistors J. Appl. Phys. 101 104503
  118. [119]Beyer A, Stegmüller A, Oelerich J O, Jandieri K, Werner K, Mette G, Stolz W, Baranovskii S D, Tonner R and Volz K 2016 Pyramidal Structure Formation at the Interface between III/V Semiconductors and Silicon Chem. Mater. 28 3265–75
  119. [120]Balaghi L, Bussone G, Grifone R, Hübner R, Grenzer J, Ghorbani-Asl M, Krasheninnikov A V., Schneider H, Helm M and Dimakis E 2019 Widely tunable GaAs bandgap via strain engineering in core/shell nanowires with large lattice mismatch Nat. Commun. 10 1–10
  120. [121]Alekseev P A, Sharov V A, Borodin B R, Dunaevskiy M S, Reznik R R and Cirlin G E 2020 Effect of the Uniaxial Compression on the GaAs Nanowire Solar Cell Micromachines 11 581
  121. [122]Lim B, Cui X Y and Ringer S P 2021 Strain-mediated bandgap engineering of straight and bent semiconductor nanowires Phys. Chem. Chem. Phys. 23 5407–14
  122. [123]Signorello G, Karg S, Björk M T, Gotsmann B and Riel H 2013 Tuning the Light Emission from GaAs Nanowires over 290 meV with Uniaxial Strain Nano Lett. 13 917
  123. [124]Grönqvist J, Søndergaard N, Boxberg F, Guhr T, Åberg S and Xu H Q 2009 Strain in semiconductor core-shell nanowires J. Appl. Phys. 106 053508
  124. [125]Signorello G, Lörtscher E, Khomyakov P A, Karg S, Dheeraj D L, Gotsmann B, H. W and Riel H 2014 Inducing a direct-to-pseudodirect bandgap transition in wurtzite GaAs nanowires with uniaxial stress Nat. Commun. 5 3655
  125. [126]Copple A, Ralston N and Peng X 2012 Engineering direct-indirect band gap transition in wurtzite GaAs nanowires through size and uniaxial strain Appl. Phys. Lett. 100 193108
  126. [127]Assali S, Zardo I, Plissard S, Kriegner D, Verheijen M A, Bauer G, Meijerink A, Belabbes A, Bechstedt F, Haverkort J E M and Bakkers E P A M 2013 Direct Band Gap Wurtzite Gallium Phosphide Nanowires Nano Lett. 13 1559–63
  127. [128]Peng X and Copple A 2013 Origination of the direct-indirect band gap transition in strained wurtzite and zinc-blende GaAs nanowires: A first principles study Phys. Rev. B 87 115308
  128. [129]New Semiconductor Materials. Biology systems. Characteristics and Properties, www.matprop.ru, last accessed 22.08.2022
  129. [130]Kresse G and Hafner J 1993 Ab initio molecular dynamics for liquid metals Phys. Rev. B 47 558–61
  130. [131]Kresse G and Hafner J 1994 Ab initio molecular-dynamics simulation of the liquid-metalamorphous-semiconductor transition in germanium Phys. Rev. B 49 14251–69
  131. [132]Kresse G and Furthmüller J 1996 Efficiency of ab-initio total energy calculations for metals and semiconductors using a plane-wave basis set J. Comput. Mater. Sci. 6 15–50
  132. [133]Kresse G and Furthmüller J 1996 Efficient iterative schemes for ab initio total-energy calculations using a plane-wave basis set Phys. Rev. B 54 11169–86
  133. [134]Blöchl P E 1994 Projector augmented-wave method Phys. Rev. B 50 17953–79
  134. [135]Kresse G and Joubert D 1999 From ultrasoft pseudopotentials to the projector augmented-wave method Phys. Rev. B 59 1758–75
  135. [136]Monkhorst H J and Pack J D 1976 Special points for Brillouin-zone integrations Phys. Rev. B 13 5188–92
  136. [137]Grimme S, Ehrlich S and Goerigk L 2011 Effect of the damping function in dispersion corrected density functional theory J. Comput. Chem. 32 1456–65
  137. [138]Grimme S, Antony J, Ehrlich S and Krieg H 2010 A consistent and accurate ab initio parametrization of density functional dispersion correction (DFT-D) for the 94 elements H-Pu J. Chem. Phys. 132 154104
  138. [139]Prins A, Adams A and Sweeney S 2012 Pressure Studies Semiconductor Research: Experimental Techniques ed A Patane and N Balkan (Berlin, Heidelberg: Springer Berlin Heidelberg) pp 171–95
  139. [140]Fratanduono D E, Millot M, Braun D G, Ali S J, Fernandez-Pañella A, Seagle C T, Davis J-P, Brown J L, Akahama Y, Kraus R G, Marshall M C, Smith R F, O’Bannon E F, McNaney J M and Eggert J H 2021 Establishing gold and platinum standards to 1 terapascal using shockless compression Science 372 1063–8
  140. [141]Dubrovinsky L, Dubrovinskaia N, Prakapenka V B and Abakumov A M 2012 Implementation of micro-ball nanodiamond anvils for high-pressure studies above 6 Mbar Nat. Commun. 3 1163
  141. [142]Dubrovinsky L, Dubrovinskaia N, Bykova E, Bykov M, Prakapenka V, Prescher C, Glazyrin K, Liermann H-P, Hanfland M, Ekholm M, Feng Q, Pourovskii L V., Katsnelson M I, Wills J M and Abrikosov I A 2015 The most incompressible metal osmium at static pressures above 750 gigapascals Nature 525 226–9
  142. [143]Katiyar A K, Thai K Y, Yun W S, Lee J and Ahn J 2020 Breaking the absorption limit of Si toward SWIR wavelength range via strain engineering Sci. Adv. 6 eabb0576
  143. [144]Yu P Y 2011 High pressure semiconductor physics: Looking toward the future on the shoulder of the past Phys. status solidi 248 1077–82
  144. [145]Snider E, Dasenbrock-Gammon N, McBride R, Debessai M, Vindana H, Vencatasamy K, Lawler K V., Salamat A and Dias R P 2020 Room-temperature superconductivity in a carbonaceous sulfur hydride Nature 586 373–7
  145. [146]Dang C, Chou J P, Dai B, Chou C T, Yang Y, Fan R, Lin W, Meng F, Hu A, Zhu J, Han J, Minor A M, Li J and Lu Y 2021 Achieving large uniform tensile elasticity in microfabricated diamond Science 371 76–8
  146. [147]Shi Z, Dao M, Tsymbalov E, Shapeev A, Li J and Suresh S 2020 Metallization of diamond Proc. Natl. Acad. Sci. 117 24634
  147. [148]Cardona M 2007 12th International Conference on High Pressure Semiconductor Physics (HPSP-12): Concluding remarks Phys. status solidi 244 481–7
  148. [149]Almonacid G, Martín-Rodríguez R, Renero-Lecuna C, Pellicer-Porres J, Agouram S, Valiente R, González J, Rodríguez F, Nataf L, Gamelin D R and Segura A 2016 Structural Metastability and Quantum Confinement in Zn₁₋ₓCoₓO Nanoparticles Nano Lett. 16 5204–12
  149. [150]Adler P, Schwarz U, Syassen K, Rozenberg G K, Machavariani G Y, Milner A P, Pasternak M P and Hanfland M 1999 Collapse of the charge disproportionation and covalency-driven insulator-metal transition in Sr₃Fe₂O₇ under pressure Phys. Rev. B 60 4609–17
  150. [151]Nelson R, Ertural C, George J, Deringer V L, Hautier G and Dronkowski R 2020 LOBSTER: Local orbital projections, atomic charges, and chemical-bonding analysis from projector-augmented-wave-based density-functional theory J. Comput. Chem. 41 1931
  151. [152]Maintz S, Deringer V L, Tchougréeff A L and Dronkowski R 2016 LOBSTER: A tool to extract chemical bonding from plane-wave based DFT J. Comput. Chem. 37 1030–5
  152. [153]Grivickas P, McCluskey M D and Gupta Y M 2009 Transformation of GaAs into an indirect L-band-gap semiconductor under uniaxial strain Phys. Rev. B 80 073201
  153. [154]Yan Q, Rinke P, Scheffler M and de Walle C G 2009 Strain effects in group-III nitrides: Deformation potentials for AlN, GaN, and InN Appl. Phys. Lett. 95 121111
  154. [155]Birch F 1947 Finite Elastic Strain of Cubic Crystals Phys. Rev. 71 809–24
  155. [156]Misra G, Tripathi P and Goyal S C 2007 Bulk modulus of semiconductors and its pressure derivatives Philos. Mag. Lett. 87 393–401
  156. [157]Van Camp P E, Van Doren V E and Devreese J T 1990 Pressure dependence of the electronic properties of cubic III-V In compounds Phys. Rev. B 41 1598–602
  157. [158]Potter R F 1956 Indirect Transitions in Indium Antimonide Phys. Rev. 103 861–2

Paper details

vlnc:W_rt6g8p4z
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents