betaFeedback

WorksPhysics and Astronomy

Mueller Matrix Decomposition for a General Rotating Compensator Ellipsometer

Abstract

This work develops a Mueller matrix decomposition that factors a nondepolarizing Mueller matrix MM into three components M=T1DT2M = T_1 D T_2, where the elements DD, which correspond to a diagonal Jones matrix, are separated from rotations and circular diattenuation T1,T2T_1, T_2. This decomposition is employed to calibrate a prototype reflective rotating-compensator ellipsometer designed to operate using extreme ultraviolet (EUV) radiation. This decomposition allows for the measurement of the full Mueller matrix of a sample without full knowledge of the compensators or the source polarization, while allowing for significant diattenuation and retardance for the optics. A generalization of the decomposition is developed for depolarizing Mueller matrices, and the technique is tested on reflection data collected on an Au mirror at 266266 nm.

Introduction

NIST has developed a dual-rotating-compensator spectroscopic Mueller-matrix ellipsometer that operates in the extreme ultraviolet (EUV) [1]. This ellipsometer modulates the polarization of light incident on a sample with a rotating compensator optic, and the polarization of light scattered from the sample is modulated in the same way to analyze the change in polarization. In this way, the full Mueller matrix of a sample can be extracted. Typical retarding compensators for ultraviolet (UV)/visible/near-infrared (NIR) wavelengths have well-characterized transmissive optics. However, because most materials are strongly absorbing in the EUV, all optics in the EUV ellipsometer must be reflective instead of transmissive. Thus, each compensator is a series of mirrors arranged as a chevron [2, 3], as depicted in Figure 1. Unlike typical retarding compensators for UV/visible/NIR wavelengths, each chevron acts as a combination retarder and diattenuator; this behavior is described by a Mueller matrix MchevronM_{\mathrm{chevron}}, which depends heavily on reflection angle, wavelength, and mirror surface [3, 4]. Our chevrons in general possess significant diattenuation and retardance. Imperfections in mirror alignment as well as surface changes, such as carbon growth after exposure to EUV radiation, make MchevronM_{\mathrm{chevron}} not only unknown, but also potentially unstable over long time scales. This necessitates a measurement scheme which can be employed to calibrate the system without prior knowledge.

Schematic of a rotating-compensator ellipsometer and a four-mirror chevron geometry

Figure 1. Left: Schematic of a rotating-compensator ellipsometer. The optics PSA and PSG, the incoming source QQ, and the detector PP must be calibrated with a fit. The straight geometry is used to calibrate (Q,MPSG)(Q, M_{\mathrm{PSG}}) and (P,MPSA)(P, M_{\mathrm{PSA}}), while the reflection geometry is employed to extract MsampleM_{\mathrm{sample}}. Right: A four-mirror chevron geometry.

Light with initial Stokes polarization QQ is modulated by rotating the chevron about its optical axis, resulting in light with polarization WW incident on a sample. In the Stokes-Mueller formalism, this rotation is expressed as

W(θ)=R(θ)MchevronR(−θ)Q,(1)W(\theta) = R(\theta)M_{\mathrm{chevron}}R(-\theta)Q, \tag*{(1)}

where R(θ)R(\theta) is the rotation matrix for angle θ\theta about the optical axis. If W(θ)W(\theta) is known or measured at a number of different rotations, we seek to determine MchevronM_{\mathrm{chevron}} and QQ. Unfortunately, with only knowledge of W(θ)W(\theta), MchevronM_{\mathrm{chevron}} and QQ can never be fully identified. Consider the transformation

Mchevron′=MchevronT,Q′=T−1Q,(2)M'_{\mathrm{chevron}} = M_{\mathrm{chevron}}T,\quad Q' = T^{-1}Q, \tag*{(2)}

where the matrix TT commutes with all rotations R(θ)R(\theta). The output Stokes vector W(θ)W(\theta) remains invariant under such a transformation, and so (Mchevron,Q)(M_{\mathrm{chevron}}, Q) cannot be distinguished from (Mchevron′,Q′)(M'_{\mathrm{chevron}}, Q').

Further author information: (Send correspondence to A.C.) A.C.: E-mail: [email protected]

Matrix Decompositions

This section summarizes our two matrix decompositions: one for nondepolarizing components (section 2.1), and one which allows for depolarization (section 2.2). Detailed proofs of their construction are given in Appendices A and B. Both factor a Mueller matrix into the form T1DT2T_1DT_2, where TT commutes with rotations and DD does not. Take a Stokes vector

\begin{bmatrix} I & Q & U & V \end{bmatrix}^{T} \tag*{(3)}\end{bmatrix}

The rotation matrix R(θ)R(\theta) is defined to be

R(θ)=[10000cos⁡2θ−sin⁡2θ00sin⁡2θcos⁡2θ00001](4)R(\theta) = \begin{bmatrix} 1 & 0 & 0 & 0 \\ 0 & \cos2\theta& -\sin2\theta& 0 \\ 0 & \sin2\theta& \cos2\theta& 0 \\ 0 & 0 & 0 & 1 \end{bmatrix} \tag*{(4)}

where θ\theta is the angle of rotation about the beam propagation path.

Nondepolarizing Matrices

Define the generalized rotation matrix TT (a combination of circular diattenuation and rotation) as

T(α,β)=[cosh⁡2α00sinh⁡2α0cos⁡2β−sin⁡2β00sin⁡2βcos⁡2β0sinh⁡2α00cosh⁡2α](5)T(\alpha,\beta) = \begin{bmatrix} \cosh2\alpha& 0 & 0 & \sinh2\alpha\\ 0 & \cos2\beta& -\sin2\beta& 0 \\ 0 & \sin2\beta& \cos2\beta& 0 \\ \sinh2\alpha& 0 & 0 & \cosh2\alpha \end{bmatrix} \tag*{(5)}

These TT matrices can be understood as the boost and rotation aspect of the Lorentz group [8, 9], and can be identified as circular diattenuation and rotations [21]. While the β\beta components in TT are clearly a rotation, the α\alpha components correspond to circular diattenuation. As expressed in Eq. (5), the TT matrix is not physical as it has optical gain (cosh⁡2α≥1\cosh2\alpha\ge1); a normalization factor of e−2∣α∣e^{-2|\alpha|} may be multiplied to the matrix if one wishes to use physically realizable Mueller matrices 1. All elements of this group satisfy

[T(α,β),R(θ)]=0 for all θ(6)[T(\alpha,\beta),R(\theta)] = 0 \text{ for all } \theta \tag*{(6)}
T(α1,β1)T(α2,β2)=T(α1+α2,β1+β2).(7)T(\alpha_1,\beta_1)T(\alpha_2,\beta_2) = T(\alpha_1+\alpha_2,\beta_1+\beta_2). \tag*{(7)}

where the brackets in the first line denote a commutator. For a nondepolarizing matrix MnondepolM_{\mathrm{nondepol}}, i.e., one fully described by a complex 2×22 \times2 Jones matrix, we claim there is a decomposition

Mnondepol=T(α1,β1) Mdiag(τ,N,C,S) T(α2,β2)(8)M_{\mathrm{nondepol}} = T(\alpha_1,\beta_1)\,M_{\mathrm{diag}}(\tau,N,C,S)\,T(\alpha_2,\beta_2) \tag*{(8)}

such that the diagonal Mueller matrix MdiagM_{\mathrm{diag}} reads

Mdiag(τ,N,C,S)=τ[1N00N10000CS00−SC],N2+C2+S2=1.(9)M_{\mathrm{diag}}(\tau,N,C,S)=\tau \begin{bmatrix} 1 & N & 0 & 0\\ N & 1 & 0 & 0\\ 0 & 0 & C & S\\ 0 & 0 & -S & C \end{bmatrix}, \qquad N^2+C^2+S^2=1. \tag*{(9)}

Thus, MnondepolM_{\mathrm{nondepol}} is fully described by 7 independent parameters. The derivation of this decomposition is given in Appendix A.

General Depolarizing Matrices

The above transformation can be further generalized if the optical elements are depolarizing. In this case, the circular diattenuation is no longer characterized by a single parameter α\alpha, and the 4×44 \times4 matrices that commute with R(θ)R(\theta) instead read

L(U,θ)=[u1100u120cos⁡2θ−sin⁡2θ00sin⁡2θcos⁡2θ0u2100u22],U=[u11u12u21u22].(10)L(U,\theta)= \begin{bmatrix} u_{11} & 0 & 0 & u_{12}\\ 0 & \cos2\theta& -\sin2\theta& 0\\ 0 & \sin2\theta& \cos2\theta& 0\\ u_{21} & 0 & 0 & u_{22} \end{bmatrix}, \qquad U= \begin{bmatrix} u_{11} & u_{12}\\ u_{21} & u_{22} \end{bmatrix}. \tag*{(10)}

These matrices LL obey

[L(U,θ′),R(θ)]=0for all θ(11)[L(U,\theta'),R(\theta)]=0\quad\text{for all }\theta \tag*{(11)}
L(U,θ1)L(V,θ2)=L(UV,θ1+θ2),(12)L(U,\theta_1)L(V,\theta_2)=L(UV,\theta_1+\theta_2), \tag*{(12)}

as LL is block diagonal. We claim a general Mueller matrix MM may be decomposed as

M=L(U,θ1)Mspecial(p1,p2)(τ,N,C,S,A,B)L(V,θ2),(13)M=L(U,\theta_1)M_{\mathrm{special}}^{(p_1,p_2)}(\tau,N,C,S,A,B)L(V,\theta_2), \tag*{(13)}

where Mspecial(p1,p2)M_{\mathrm{special}}^{(p_1,p_2)} takes the form

Mspecial(p1,p2)(τ,N,C,S,A,B)=τ[1p1N0BN10000CSA0−p2SC],p1=±1, p2=±1.(14)M_{\mathrm{special}}^{(p_1,p_2)}(\tau,N,C,S,A,B)=\tau \begin{bmatrix} 1 & p_1N & 0 & B\\ N & 1 & 0 & 0\\ 0 & 0 & C & S\\ A & 0 & -p_2S & C \end{bmatrix}, \qquad p_1=\pm1,\ p_2=\pm1. \tag*{(14)}

Thus, the 4×44 \times4 MM is fully described by 16 parameters, and the signs p1,p2p_1,p_2 are uniquely determined by the other 16 parameters. The proof of the existence of this decomposition is given in Appendix B.

Unlike the nondepolarizing case, there is no reason to expect that the matrices LL, MspecialM_{\mathrm{special}} correspond to physical processes; indeed, tests of the decomposition for random Mueller matrices often yield LL, MM that are unphysical. Nevertheless, the decomposition in Equation (13) remains mathematically correct and serves as a way to isolate the components of the Mueller matrix that can be fit in a rotating compensator ellipsometer.

Ellipsometer calibration procedure

A simplified schematic of the dual rotating compensator ellipsometer is depicted in Figure 1. It consists of two rotating optics, named the polarization state generator (PSG) and polarization state analyzer (PSA). By rotating the PSA and PSG, the polarization state of the incident light W(θPSG)W(\theta_{\mathrm{PSG}}) and the analyzer sensitivity A(θPSA)A(\theta_{\mathrm{PSA}}) can be modulated; any other optics have been absorbed into the rotation-independent Stokes vectors of source polarization QQ and detector sensitivity PP. If the PSG and PSA are designed appropriately, then W(θPSG)W(\theta_{\mathrm{PSG}}) and A(θPSA)A(\theta_{\mathrm{PSA}}) span enough of the Poincaré sphere to determine the full Mueller matrix of a sample MsampleM_{\mathrm{sample}}.

The Mueller matrices of the PSG and PSA optics, as well as the Stokes vectors of the source and the detector, are unknown and must be calibrated. To calibrate, a ‘straight’ measurement is performed, in which the PSA and PSG are rotated at different angles and the output light intensity Sstraight(θPSA,θPSG)S_{\mathrm{straight}}(\theta_{\mathrm{PSA}},\theta_{\mathrm{PSG}}) is measured, without the presence of a sample:

Sstraight(θPSA,θPSG)=A(θPSA)W(θPSG)(15)S_{\mathrm{straight}}(\theta_{\mathrm{PSA}},\theta_{\mathrm{PSG}}) = A(\theta_{\mathrm{PSA}})W(\theta_{\mathrm{PSG}}) \tag*{(15)}
A(θPSA)=PR(θPSA)MPSAR(−θPSA)(16)A(\theta_{\mathrm{PSA}}) = P R(\theta_{\mathrm{PSA}})M_{\mathrm{PSA}}R(-\theta_{\mathrm{PSA}}) \tag*{(16)}
W(θPSG)=R(θPSG)MPSGR(−θPSG)Q,(17)W(\theta_{\mathrm{PSG}}) = R(\theta_{\mathrm{PSG}})M_{\mathrm{PSG}}R(-\theta_{\mathrm{PSG}})Q, \tag*{(17)}

where the measurement output is SstraightS_{\mathrm{straight}}, and PP, QQ are the Stokes vectors corresponding to the detector and incoming source, respectively. The matrices MPSAM_{\mathrm{PSA}}, MPSGM_{\mathrm{PSG}} are the Mueller matrices of the rotating compensators.

These straight measurements alone are not enough to fully characterize the ellipsometer – that is, to unambiguously determine WW and AA. Decomposing the Mueller matrices of the PSA and PSG yields

MPSA=TPSA1DPSATPSA2,MPSG=TPSG1DPSGTPSG2,(18)M_{\mathrm{PSA}} = T_{\mathrm{PSA1}}D_{\mathrm{PSA}}T_{\mathrm{PSA2}}, \qquad M_{\mathrm{PSG}} = T_{\mathrm{PSG1}}D_{\mathrm{PSG}}T_{\mathrm{PSG2}}, \tag*{(18)}

where DPSAD_{\mathrm{PSA}}, DPSGD_{\mathrm{PSG}} have the form of Eq. (9). Some of the TT matrices cannot be fit from the straight measurement alone:

A(θPSA)=P′R(θPSA)DPSAR(−θPSA)TPSA2(19)A(\theta_{\mathrm{PSA}}) = P^{\prime}R(\theta_{\mathrm{PSA}})D_{\mathrm{PSA}}R(-\theta_{\mathrm{PSA}})T_{\mathrm{PSA2}} \tag*{(19)}
W(θPSG)=TPSG1R(θPSG)DPSGR(−θPSG)Q′(20)W(\theta_{\mathrm{PSG}}) = T_{\mathrm{PSG1}}R(\theta_{\mathrm{PSG}})D_{\mathrm{PSG}}R(-\theta_{\mathrm{PSG}})Q^{\prime} \tag*{(20)}
Sstraights(θPSA,θPSG)=P′R(θPSA)DPSAR(θPSG−θPSA)T′DPSGR(−θPSG)Q′(21)S_{\mathrm{straights}}(\theta_{\mathrm{PSA}},\theta_{\mathrm{PSG}}) = P^{\prime}R(\theta_{\mathrm{PSA}})D_{\mathrm{PSA}}R(\theta_{\mathrm{PSG}}-\theta_{\mathrm{PSA}})T^{\prime}D_{\mathrm{PSG}}R(-\theta_{\mathrm{PSG}})Q^{\prime} \tag*{(21)}

where

P′=PTPSA1,Q′=TPSG2Q,T′=TPSA2TPSG1.(22)P' = PT_{\mathrm{PSA1}},\quad Q' = T_{\mathrm{PSG2}}Q,\quad T' = T_{\mathrm{PSA2}}T_{\mathrm{PSG1}}. \tag*{(22)}

We have used the fact that RR and TT commute. In other words, it is impossible to determine both TPSA2T_{\mathrm{PSA2}} and TPSG1T_{\mathrm{PSG1}} individually – only their product T′T' is known. When fitting the straight measurement, we obtain normalized values for P′P', Q′Q', T′T', DPSAD_{\mathrm{PSA}}, DPSGD_{\mathrm{PSG}}, and one overall multiplicative constant τ\tau. However, when measuring a sample, one must know TPSG2T_{\mathrm{PSG2}} and TPSA1T_{\mathrm{PSA1}}. This is not possible with the straight measurement.

A second calibration measurement involving an object with a Mueller matrix of NCS form Mcal,diagM_{\mathrm{cal,diag}} must be performed to fix TPSA2T_{\mathrm{PSA2}} and TPSG1T_{\mathrm{PSG1}}. The measured quantity is

Scal(θPSA,θPSG)=A(θPSA)Mcal,diagW(θPSG).(23)S_{\mathrm{cal}}(\theta_{\mathrm{PSA}},\theta_{\mathrm{PSG}}) = A(\theta_{\mathrm{PSA}})M_{\mathrm{cal,diag}}W(\theta_{\mathrm{PSG}}). \tag*{(23)}

So long as Mcal,diagM_{\mathrm{cal,diag}} is of NCS form and not proportional to the identity (that is, it is not a basic filter that affects ss-polarized and pp-polarized light in the same manner), this second measurement, in addition to the straight measurement, is enough to determine TPSA2T_{\mathrm{PSA2}} and TPSG1T_{\mathrm{PSG1}} and thus fully calibrate a nondepolarizing ellipsometer. An example of such an optic would be a mirror constructed of an isotropic material. A similar requirement was noted for a calibration where the chevrons were Fresnel rhombs and were modeled as elliptical retarders by the authors of Ref. [18].

If this second calibration is not performed, important information can still be extracted about the sample. Assuming the nondepolarizing form for the sample,

Ssample(θPSA,θPSG)=A(θPSA)Tsample,1Msample,diagTsample,2W(θPSG).(24)S_{\mathrm{sample}}(\theta_{\mathrm{PSA}},\theta_{\mathrm{PSG}}) = A(\theta_{\mathrm{PSA}})T_{\mathrm{sample,1}}M_{\mathrm{sample,diag}}T_{\mathrm{sample,2}}W(\theta_{\mathrm{PSG}}). \tag*{(24)}

While Tsample,1T_{\mathrm{sample,1}} and Tsample,2T_{\mathrm{sample,2}} cannot be extracted (as TPSA1,TPSG2T_{\mathrm{PSA1}},T_{\mathrm{PSG2}} are undetermined), their product can be, as well as the diagonal components Msample,diagM_{\mathrm{sample,diag}}. If one expects the sample to be close to NCS form, then Msample,diagM_{\mathrm{sample,diag}} may be extracted without knowing Tsample,1,Tsample,2T_{\mathrm{sample,1}},T_{\mathrm{sample,2}}.

In summary, to determine the Mueller matrix for a sample that is supposed to be of NCS form (such as a thin film or multilayer), calibration with measurement in a straight geometry is sufficient. If the sample is expected to deviate from this form, then a second measurement using a diagonal calibration artifact is necessary to determine the full Mueller matrix of the sample.

Generalized Matrix Decomposition

Can general depolarizing chevrons can be calibrated according to the steps given above? A straight measurement, allowing for depolarizing chevrons, would have 22 floating parameters: 3 for the input and output polarizations, 5 for each of the chevrons (NN, CC, SS, AA, BB), 5 for the generalized rotation/circular dichroism matrix between the PSA and PSG, and one total normalization, for a total of 22. A straight measurement has 25 different Fourier harmonics, and so naively one might expect the straight measurement to be determined as we have more equations than variables. However, not all of the 25 harmonics are independent; numerical simulations with random chevrons show that of these 25 only 19 are linearly independent, and thus the general problem of depolarizing chevrons cannot be solved with our technique.

However, for chevrons close to NCS form, one can model the most important depolarizing effects. Consider that the incident beam strikes the chevron’s mirrors at grazing incidence, and so the large beam profile averages the Mueller matrices over its area. To treat this possibility, it is possible to relax the condition that N2+C2+S2=1N^2+C^2+S^2=1, corresponding to many different Mueller matrices being averaged over by the beam. Such a straight fit only involves two extra degrees of freedom.

Numerical Verification of Decomposition

Random Mueller matrices were generated by creating convex combinations of valid nondepolarizing matrices. The generalized decomposition was performed and it was verified that all four combinations of p1,p2p_1,p_2 were accessed in the decompositions: see Figure 2. It was also observed that the magnitude of AA and BB could at times exceed 1, giving a nonphysical Mueller matrix. This situation implies that the Mueller matrix is far from NCS form, and a different parameterization would be more appropriate.

Ratios of Mueller matrices that factor into forms of $p_1$, $p_2$

Figure 2. Ratios of Mueller matrices that factor into forms of p1p_1, p2p_2. A nondepolarizing matrix always has p1=p2=1p_1 = p_2 = 1, but mixtures in general may be any one of all four.

Experimental verification via measurement of a mirror

The rotating compensator ellipsometer that NIST has developed was first tested using 266 nm light by frequency-doubling a commercial CW 532 nm laser; this allowed for testing the performance of the system’s optics outside of vacuum, and evaluating the performance of the rotating chevrons as compensators by comparing with commercial ellipsometers. Measurements were taken in both a straight geometry, as well as using a sample of a gold mirror in reflection geometry at an incidence angle of 65°. Further details of the instrument design and measurement apparatus are described in a separate paper [1].

Figure 3 shows the measured signal SS, the intensity of light normalized to the beam intensity by picking off a portion of the beam; thus, the intensity ratio is unitless. A small asymmetry in the signal can be seen when rotating either the PSG or PSA by 180°. This could be caused either by misalignment of the optical axis and the rotational axis or by occlusion of portions of the beam (mechanical vignetting). The vignetting is accounted for by modulating the occluded beam as a paraboloid restricted to the interval [0,1] that multiplies the overall signal.

Contour plots of measured intensity for Straights and Au Sample

Figure 3. Data from a prototype ellipsometer used to determine the ellipsometric parameters N,C, and S of an Au mirror at λ=266\lambda= 266 nm. Left: Contour plots of measured intensity of light as a function of rotation angles of PSG and PSA in the straight geometry. Right: Contour plots after reflection off of a thick Au film at an incidence angle of 65∘65^\circ (25∘25^\circ grazing).

S~(θPSA,θPSG)=O(θPSA,θPSG)S(θPSA,θPSG)(25)\widetilde{S}(\theta_{\mathrm{PSA}},\theta_{\mathrm{PSG}}) = \mathcal{O}(\theta_{\mathrm{PSA}},\theta_{\mathrm{PSG}}) S(\theta_{\mathrm{PSA}},\theta_{\mathrm{PSG}}) \tag*{(25)}
O(θPSA,θPSG)=min⁡[1.0,cPSG(θPSG−θPSG,0)2+cPSA(θPSA−θPSA,0)2+d],cPSA,cPSG,d≥0,(26)\mathcal{O}(\theta_{\mathrm{PSA}},\theta_{\mathrm{PSG}}) = \min[1.0, c_{\mathrm{PSG}}(\theta_{\mathrm{PSG}}-\theta_{\mathrm{PSG},0})^2 + c_{\mathrm{PSA}}(\theta_{\mathrm{PSA}}-\theta_{\mathrm{PSA},0})^2 + d], \quad c_{\mathrm{PSA}}, c_{\mathrm{PSG}}, d \ge0, \tag*{(26)}

where cPSGc_{\mathrm{PSG}}, cPSAc_{\mathrm{PSA}}, θPSG,0\theta_{\mathrm{PSG},0}, θPSA,0\theta_{\mathrm{PSA},0}, dd are parameters modeling a paraboloid intended to capture the mechanical vignetting.

The nondepolarizing matrix decomposition was used to find the relevant optical properties of the PSA, PSG, and the NCS values of the optic, as per Eq. (8). The straight measurements were fit to Eq. (25) using 13 ellipsometric parameters + 5 vignetting parameters. The measured NN, CC, SS values of the gold mirror were found to match with measurements taken by a commercial ellipsometer, within in-sample variations. The measured values for NN, CC, and SS are reported in Table 1. The straight calibration found the normalized Stokes and Mueller matrices to be

NIST SECommercial SE
N0.534±0.0010.534 \pm0.0010.539±0.0040.539 \pm0.004
C−0.120±0.002-0.120 \pm0.002−0.123±0.007-0.123 \pm0.007
S0.837±0.0010.837 \pm0.0010.833±0.0030.833 \pm0.003

Table 1. Comparison of spectroscopic ellipsometry (SE) results to a commercial instrument. Standard deviations for the commercial SE represent the standard deviation across measurements at 5 different spots on the sample combined with the uncertainty of the device itself.

DPSA=[10.878000.878100000.377−0.294000.2940.377]±[00.001000.001000000.0020.004000.0040.002],DPSG=[10.880000.880100000.306−0.363000.3630.306]±[00.001000.001000000.0010.001000.0010.001],P′=[10.5270.020−0.022]±[00.0010.0010.008],Q′=[1−0.999−0.007−0.015]±[00.0010.0010.001],T′=[1.000000.00801.000−0.021000.0211.00000.008001.000]±[0.001000.00300.0010.002000.0020.00100.003000.001].(27)\begin{aligned} D_{\mathrm{PSA}} &= \begin{bmatrix} 1 & 0.878 & 0 & 0 \\ 0.878 & 1 & 0 & 0 \\ 0 & 0 & 0.377 & -0.294 \\ 0 & 0 & 0.294 & 0.377 \end{bmatrix} \pm\begin{bmatrix} 0 & 0.001 & 0 & 0 \\ 0.001 & 0 & 0 & 0 \\ 0 & 0 & 0.002 & 0.004 \\ 0 & 0 & 0.004 & 0.002 \end{bmatrix},\\ D_{\mathrm{PSG}} &= \begin{bmatrix} 1 & 0.880 & 0 & 0 \\ 0.880 & 1 & 0 & 0 \\ 0 & 0 & 0.306 & -0.363 \\ 0 & 0 & 0.363 & 0.306 \end{bmatrix} \pm\begin{bmatrix} 0 & 0.001 & 0 & 0 \\ 0.001 & 0 & 0 & 0 \\ 0 & 0 & 0.001 & 0.001 \\ 0 & 0 & 0.001 & 0.001 \end{bmatrix},\\ P' &= \begin{bmatrix} 1 & 0.527 & 0.020 & -0.022 \end{bmatrix} \pm\begin{bmatrix} 0 & 0.001 & 0.001 & 0.008 \end{bmatrix},\\ Q' &= \begin{bmatrix} 1 \\ -0.999 \\ -0.007 \\ -0.015 \end{bmatrix} \pm\begin{bmatrix} 0 \\ 0.001 \\ 0.001 \\ 0.001 \end{bmatrix},\\ T' &= \begin{bmatrix} 1.000 & 0 & 0 & 0.008 \\ 0 & 1.000 & -0.021 & 0 \\ 0 & 0.021 & 1.000 & 0 \\ 0.008 & 0 & 0 & 1.000 \end{bmatrix} \pm\begin{bmatrix} 0.001 & 0 & 0 & 0.003 \\ 0 & 0.001 & 0.002 & 0 \\ 0 & 0.002 & 0.001 & 0 \\ 0.003 & 0 & 0 & 0.001 \end{bmatrix}. \tag*{(27)} \end{aligned}

All uncertainties are reported as estimates of the standard uncertainty.

The fits reported in Table 1 and in Eq. (27) employed an uncertainty analysis using the techniques similar to those in Ref. [22]: by modeling the discrepancy with Gaussian process regression, it is possible to place uncertainty bounds even without a formula modeling the systematic error. The details of this technique will be reported in upcoming work. If the systematic error was neglected, the reported uncertainty would be an order of magnitude too small. We have restricted the uncertainties to be at minimum 0.001.

It should be noted that while the chevrons of the PSA and PSG were aligned to within 0.1∘0.1^\circ, the fit found a relative difference of 0.6∘0.6^\circ. This is consistent with the misalignment of the mirrors within the chevrons inducing roll in the beam, and would not have been identified if the Mueller matrices of the chevrons were forced to be of Mdiag(τ,N,C,S)M_{\mathrm{diag}}(\tau,N,C,S) form.

Conclusion

In this work, we have derived a Mueller matrix decomposition that separates the diagonal NCS form from rotations and circular diattenuation. The decomposition is invaluable for fitting ellipsometers that involve rotating optics with significant diattenuation and retardance – even without complete calibration, it is possible to extract meaningful information about samples. The technique has been applied to measurements performed with NIST’s EUV ellipsometer, where the chevrons possess both unknown diattenuation and retardance. The depolarizing case is also derived, and its applicability in more general ellipsometers has been discussed. We expect our technique to be employed in future work with our EUV ellipsometer, and in general, any ellipsometer in which standard calibration strategies are difficult or impossible.

Acknowledgments

This work was performed with funding from the CHIPS Metrology Program, part of CHIPS for America, National Institute of Standards and Technology, U.S. Department of Commerce.

Data Availability Statement

Data and code used to calculate quantities and generate figures in this manuscript are available upon request.

Conflicts of Interest

The authors declare no conflicts of interest.

Official contribution of the National Institute of Standards and Technology; not subject to copyright in the United States.

Proof of Nondepolarizing Decomposition

For nondepolarizing optics, it is more convenient to work with the Jones formalism. In the Jones formalism, the matrices JJ are 2×22 \times2 and complex, and are related to the Mueller matrices MM by the formula

Mnondepol(J)=A[J⊗J∗]A−1,A=[1001100−101100i−i0].(28)M_{\mathrm{nondepol}}(J) = A[J \otimes J^{*}]A^{-1}, \quad A = \begin{bmatrix} 1 & 0 & 0 & 1 \\ 1 & 0 & 0 & -1 \\ 0 & 1 & 1 & 0 \\ 0 & i & -i & 0 \end{bmatrix}. \tag*{(28)}

A diagonal Jones matrix (one that preserves ss and pp polarization) has a Mueller matrix

Mdiag(τ,N,C,S)=τ[1N00N10000CS00−SC],(29)M_{\mathrm{diag}}(\tau,N,C,S)=\tau\begin{bmatrix}1 & N & 0 & 0 \\ N & 1 & 0 & 0 \\ 0 & 0 & C & S \\ 0 & 0 & -S & C\end{bmatrix}, \tag*{(29)}

with N2+C2+S2=1N^2+C^2+S^2=1; in the Jones formalism,

Jdiag(rs,rp)=[rs00rp].(30)J_{\mathrm{diag}}(r_s,r_p)=\begin{bmatrix}r_s & 0 \\ 0 & r_p\end{bmatrix}. \tag*{(30)}

In the Jones formalism, rotations read R(θ)=eiθσyR(\theta)=e^{i\theta\sigma_y}, with σi\sigma_i denoting the ith Pauli matrix

σx=[0110],σy=[0−ii0],σz=[100−1](31)\sigma_x=\begin{bmatrix}0 & 1 \\ 1 & 0\end{bmatrix},\quad\sigma_y=\begin{bmatrix}0 & -i \\ i & 0\end{bmatrix},\quad\sigma_z=\begin{bmatrix}1 & 0 \\ 0 & -1\end{bmatrix} \tag*{(31)}

and note the only matrices that commute with all rotations take the form

T=r+sσy,(32)T=r+s\sigma_y, \tag*{(32)}

with rr, ss complex numbers. Almost every 2×22\times2 complex matrix may be expressed as

J=a(I+bσy)(I+cσz)(I+dσy)(33)J=a(I+b\sigma_y)(I+c\sigma_z)(I+d\sigma_y) \tag*{(33)}

with a,b,c,da,b,c,d complex $2.ThisisakintoanEuleranglerotationforcomplex. This is akin to an Euler angle rotation for complex2\times 2 matrices. This claim can be proven by expanding the product and showing there is a value for a,b,c,d$ that yields (almost) any matrix:

J=a(1+bd)+ac(1−bd)σz+a(b+d)σy+iac(b−d)σx(34)J=a(1+bd)+ac(1-bd)\sigma_z+a(b+d)\sigma_y+iac(b-d)\sigma_x \tag*{(34)}
=wI+zσz+yσy+xσx,(35)=wI+z\sigma_z+y\sigma_y+x\sigma_x, \tag*{(35)}

and a,b,c,da,b,c,d can be expressed in terms of w,x,y,zw,x,y,z. Here II is the identity matrix. There are two solutions, one of which is:

a=12(w−(w2−y2)z2(x2+z2)x2+z2),(36)a=\frac{1}{2}\left(w-\frac{\sqrt{(w^2-y^2)z^2(x^2+z^2)}}{x^2+z^2}\right), \tag*{(36)}
b=−ixyz+wz2+(w2−y2)z2(x2+z2)z(−iwx+yz),(37)b=\frac{-ixyz+wz^2+\sqrt{(w^2-y^2)z^2(x^2+z^2)}}{z(-iwx+yz)}, \tag*{(37)}
c=−z(x2+z2)(w2−y2)z2(x2+z2),(38)c=-\frac{z(x^2+z^2)}{\sqrt{(w^2-y^2)z^2(x^2+z^2)}}, \tag*{(38)}
d=ixyz+wz2+(w2−y2)z2(x2+z2)z(iwx+yz),(39)d=\frac{ixyz+wz^2+\sqrt{(w^2-y^2)z^2(x^2+z^2)}}{z(iwx+yz)}, \tag*{(39)}

The other solution can be found employing the identity

−σz=σyσzσy(40)-\sigma_z=\sigma_y\sigma_z\sigma_y \tag*{(40)}
a(I+bσy)(I+cσz)(I+dσy)=a(bI+σy)(I−cσz)(dI+σy)(41)a(I+b\sigma_y)(I+c\sigma_z)(I+d\sigma_y)=a(bI+\sigma_y)(I-c\sigma_z)(dI+\sigma_y) \tag*{(41)}
=abd(I+1bσy)(I−cσz)(I+1dσy),(42)=abd\left(I+\frac{1}{b}\sigma_y\right)(I-c\sigma_z)\left(I+\frac{1}{d}\sigma_y\right), \tag*{(42)}

that is, the transform

a→abd,b→1b,c→−c,d→1d(43)a\to abd,\quad b\to\frac{1}{b},\quad c\to-c,\quad d\to\frac{1}{d} \tag*{(43)}

yields the second solution. The sole caveat is that there may be no solution if any of the quantities x2+z2x^2+z^2, w2−y2w^2-y^2, −iwx+yz-iwx+yz, iwx+yziwx+yz are 0, as the denominator for several of the expressions tends to 0 (z→0z \to0 is not an issue). For these exceptional cases, the matrix decomposition fails3.

We then turn the Jones matrices to Mueller matrices. If z=α−iβz=\alpha-i\beta, then turning ezσye^{z\sigma_y} into a Mueller matrix gives4 gives

T(α,β)=[cosh⁡2α00sinh⁡2α0cos⁡2β−sin⁡2β00sin⁡2βcos⁡2β0sinh⁡2α00cosh⁡2α](44)T(\alpha,\beta)= \begin{bmatrix} \cosh2\alpha& 0 & 0 & \sinh2\alpha\\ 0 & \cos2\beta& -\sin2\beta& 0\\ 0 & \sin2\beta& \cos2\beta& 0\\ \sinh2\alpha& 0 & 0 & \cosh2\alpha \end{bmatrix} \tag*{(44)}

Meanwhile, the diagonal matrix aI+bσzaI+b\sigma_z corresponds to a Mueller matrix of NCS form. Thus, for a pure matrix MnondepolM_{\mathrm{nondepol}}, there is a decomposition

Mnondepol=T(α1,β1)Mdiag(τ,N,C,S)T(α2,β2),(45)M_{\mathrm{nondepol}}=T(\alpha_1,\beta_1)M_{\mathrm{diag}}(\tau,N,C,S)T(\alpha_2,\beta_2), \tag*{(45)}

with the TT matrices satisfying

[T(α,β),R(θ)]=0for all θ(46)[T(\alpha,\beta),R(\theta)]=0\quad\text{for all }\theta \tag*{(46)}
T(α1,β1)T(α2,β2)=T(α1+α2,β1+β2).(47)T(\alpha_1,\beta_1)T(\alpha_2,\beta_2)=T(\alpha_1+\alpha_2,\beta_1+\beta_2). \tag*{(47)}

These TT matrices can be understood as the boost and rotation aspect of the Lorentz group [8, 9]. While the β\beta quantity in TT is a rotation, the α\alpha quantity corresponds to circular diattenuation. Because cosh is always greater than 1, this operator TT by itself does not correspond to a physical process. One may normalize the matrix by e−2∣α∣e^{-2|\alpha|} if one wishes to restrict to physically realizable Mueller matrices.

Proof of Depolarizing Decomposition

One must work with the full Mueller matrix formalism when investigating the depolarizing matrices. For notational convenience, let us exchange the second and fourth rows and columns of the Mueller matrix. Then, the rotation matrix reads

R(θ)=[1000010000cos⁡2θsin⁡2θ00−sin⁡2θcos⁡2θ](48)R(\theta)= \begin{bmatrix} 1 & 0 & 0 & 0\\ 0 & 1 & 0 & 0\\ 0 & 0 & \cos2\theta& \sin2\theta\\ 0 & 0 & -\sin2\theta& \cos2\theta \end{bmatrix} \tag*{(48)}

The only matrices that commute with all rotations take the form

L(U,θ′)=[u11u1200u21u220000cos⁡2θ′sin⁡2θ′00−sin⁡2θ′cos⁡2θ′],(49)L(U,\theta')= \begin{bmatrix} u_{11} & u_{12} & 0 & 0\\ u_{21} & u_{22} & 0 & 0\\ 0 & 0 & \cos2\theta' & \sin2\theta'\\ 0 & 0 & -\sin2\theta' & \cos2\theta' \end{bmatrix}, \tag*{(49)}

up to a multiplicative constant. Once again, we wish to factor a Mueller matrix MM as

M=L(U,θ1)Mspecialp1,p2(τ,N,C,S,A,B)L(V,θ2),(50)M=L(U,\theta_1)M_{\mathrm{special}}^{p_1,p_2}(\tau,N,C,S,A,B)L(V,\theta_2), \tag*{(50)}

where the exact form of MspecialM_{\mathrm{special}} is yet to be determined. However, we know that diagonal matrices of NCS form must be included in MspecialM_{\mathrm{special}}, and that there are 6 degrees of freedom, as the Mueller matrix has 16 and each LL has 5. The form of MspecialM_{\mathrm{special}} is derived by construction, and relies on the singular value decomposition and the QR decomposition. Recall for any real matrix MM, the singular value decomposition reads

M=UΣVT,(51)M=U\Sigma V^{T}, \tag*{(51)}

where UU, VV are orthogonal and Σ\Sigma is the nonnegative diagonal matrix of singular values. A special occurrence happens when the matrices are 2×22 \times2. In this case, orthogonal matrices are either rotations R(θ)R(\theta) or Householder reflections R(θ)σzR(\theta)\sigma_z. Thus,

M=R(θ1)ΣR(θ2),(52)M = R(\theta_1)\Sigma R(\theta_2), \tag*{(52)}

where the ‘singular values’ Σ\Sigma do not need to be positive. This formula is derived by realizing that if either UU or VV are Householder reflections, the σz\sigma_z matrix multiplies Σ\Sigma and changes the sign of one of the singular values to be negative.

The QR decomposition (and the QL decomposition) factor a matrix into an orthogonal times a triangular matrix. A further decomposition allows one to decompose the triangular matrix as a Heisenberg matrix times a diagonal matrix:

N=QR=Q[ab0c]=Q[1b/c01][a00c],(53)N = QR = Q \begin{bmatrix} a & b \\ 0 & c \end{bmatrix} = Q \begin{bmatrix} 1 & b/c \\ 0 & 1 \end{bmatrix} \begin{bmatrix} a & 0 \\ 0 & c \end{bmatrix}, \tag*{(53)}

so long as c≠0c \ne0.5 The Heisenberg matrix always has an inverse:

[1α01]−1=[1−α01](54)\begin{bmatrix} 1 & \alpha\\ 0 & 1 \end{bmatrix}^{-1} = \begin{bmatrix} 1 & -\alpha\\ 0 & 1 \tag*{(54)} \end{bmatrix}

Now consider a real 4×44 \times4 matrix, but block the elements into four matrices of size 2×22 \times2. This matrix MM is the depolarizing Mueller matrix with the second and fourth rows and columns exchanged.

M=[ABCD].(55)M = \begin{bmatrix} A & B \\ C & D \end{bmatrix}. \tag*{(55)}

Perform a generalized singular value decomposition on D=R(θ1)ΣR(θ2)D = R(\theta_1)\Sigma R(\theta_2), allowing the entries of Σ\Sigma to be negative, and enforce the second singular value of Σ\Sigma to have larger magnitude than the first and be positive. If the largest magnitude singular value is negative, multiply both Σ\Sigma and R(θ2)R(\theta_2) by −1-1. −R(θ2)=R(θ2+π2)-R(\theta_2) = R(\theta_2 + \frac{\pi}{2}) still remains a rotation and Σ\Sigma now has a positive largest singular value.

M=[I00R(θ1)][ABR(−θ2)R(−θ1)CΣ][I00R(θ2)],(56)M = \begin{bmatrix} I & 0 \\ 0 & R(\theta_1) \end{bmatrix} \begin{bmatrix} A & BR(-\theta_2) \\ R(-\theta_1)C & \Sigma\end{bmatrix} \begin{bmatrix} I & 0 \\ 0 & R(\theta_2) \end{bmatrix}, \tag*{(56)}

and now we employ a QR or QL decomposition on R(−θ1)CR(-\theta_1)C and BR(−θ2)BR(-\theta_2). Let

BR(−θ2)=Q3H3D3(57)BR(-\theta_2) = Q_3H_3D_3 \tag*{(57)}
R(−θ1)C=D4H4Q4,(58)R(-\theta_1)C = D_4H_4Q_4, \tag*{(58)}

with HH a Heisenberg matrix (either lower triangular or upper triangular) and DD a diagonal matrix.

M=[Q3H3σx00R(θ1)][A′σxD3D4σxΣ][σxH4Q400R(θ2)],(59)M = \begin{bmatrix} Q_3H_3\sigma_x & 0 \\ 0 & R(\theta_1) \end{bmatrix} \begin{bmatrix} A' & \sigma_xD_3 \\ D_4\sigma_x & \Sigma\end{bmatrix} \begin{bmatrix} \sigma_xH_4Q_4 & 0 \\ 0 & R(\theta_2) \end{bmatrix}, \tag*{(59)}
A′=σxH3−1Q3TAQ4TH4−1σx.(60)A' = \sigma_xH_3^{-1}Q_3^TAQ_4^TH_4^{-1}\sigma_x. \tag*{(60)}

Let us define

A′=[a11a12a21a22],σxD3=[0τNR−τSR0],D4σx=[0τSLτNL0],Σ=[τC00τ],(61)A' = \begin{bmatrix} a_{11} & a_{12} \\ a_{21} & a_{22} \end{bmatrix}, \quad \sigma_xD_3 = \begin{bmatrix} 0 & \tau_{NR} \\ -\tau_{SR} & 0 \end{bmatrix}, \quad D_4\sigma_x = \begin{bmatrix} 0 & \tau_{SL} \\ \tau_{NL} & 0 \end{bmatrix}, \quad \Sigma= \begin{bmatrix} \tau_C & 0 \\ 0 & \tau\end{bmatrix}, \tag*{(61)}
U=Q3H3σx=[u11u12u21u22],V=σxH4Q4=[v11v12v21v22](62)U = Q_3H_3\sigma_x = \begin{bmatrix} u_{11} & u_{12} \\ u_{21} & u_{22} \end{bmatrix}, \quad V = \sigma_xH_4Q_4 = \begin{bmatrix} v_{11} & v_{12} \\ v_{21} & v_{22} \end{bmatrix} \tag*{(62)}
M=[u11u1200u21u220000cos⁡2θ1sin⁡2θ100−sin⁡2θ1cos⁡2θ1][a11a120τNRa21a22−τSR00τSLτC0τNL00τ][v11v1200v21v220000cos⁡2θ2sin⁡2θ200−sin⁡2θ2cos⁡2θ2].(63)M = \begin{bmatrix} u_{11} & u_{12} & 0 & 0 \\ u_{21} & u_{22} & 0 & 0 \\ 0 & 0 & \cos2\theta_1 & \sin2\theta_1 \\ 0 & 0 & -\sin2\theta_1 & \cos2\theta_1 \end{bmatrix} \begin{bmatrix} a_{11} & a_{12} & 0 & \tau N_R \\ a_{21} & a_{22} & -\tau S_R & 0 \\ 0 & \tau S_L & \tau C & 0 \\ \tau N_L & 0 & 0 & \tau \end{bmatrix} \begin{bmatrix} v_{11} & v_{12} & 0 & 0 \\ v_{21} & v_{22} & 0 & 0 \\ 0 & 0 & \cos2\theta_2 & \sin2\theta_2 \\ 0 & 0 & -\sin2\theta_2 & \cos2\theta_2 \end{bmatrix}. \tag*{(63)}

As a final step, we shall apply a diagonal scale transform on the upper left block to turn the middle matrix into MspecialM_{\mathrm{special}} form:

Mspecial(p1,p2)(τ,N,C,S,A,B)=τ[1B0p1NAC−p2S00SC0N001],p1=±1, p2=±1.(64)M_{\mathrm{special}}^{(p_1,p_2)}(\tau,N,C,S,A,B) = \tau \begin{bmatrix} 1 & B & 0 & p_1N \\ A & C & -p_2S & 0 \\ 0 & S & C & 0 \\ N & 0 & 0 & 1 \end{bmatrix}, \qquad p_1=\pm1,\ p_2=\pm1. \tag*{(64)}
\begin{bmatrix} r_1 & 0 & 0 & 0 \\ 0 & s_1 & 0 & 0 \\ 0 & 0 & 1 & 0 \\ 0 & 0 & 0 & 1 \end{bmatrix} \begin{bmatrix} a_{11} & a_{12} & 0 & \tau N_R \\ a_{21} & a_{22} & -\tau S_R & 0 \\ 0 & \tau S_L & \tau C & 0 \\ \tau N_L & 0 & 0 & \tau \end{bmatrix} \begin{bmatrix} r_2 & 0 & 0 & 0 \\ 0 & s_2 & 0 & 0 \\ 0 & 0 & 1 & 0 \\ 0 & 0 & 0 & 1 \end{bmatrix} = \begin{bmatrix} r_1r_2a_{11} & s_2r_1a_{12} & 0 & \tau r_1N_R \\ s_1r_2a_{21} & s_1s_2a_{22} & -\tau s_1S_R & 0 \\ 0 & \tau s_2S_L & \tau C & 0 \\ \tau r_2N_L & 0 & 0 & \tau \end{bmatrix}. \tag*{(65)}\end{bmatrix}

To match the form of MspecialM_{\mathrm{special}}, we require

r1r2a11=τ,r2NL=p1r1NR(66)r_1r_2a_{11}=\tau,\qquad r_2N_L=p_1r_1N_R \tag*{(66)}
s1s2a22=τC,s1SR=p2s2SL.(67)s_1s_2a_{22}=\tau C,\qquad s_1S_R=p_2s_2S_L. \tag*{(67)}

In order for these two systems to have real solutions r1,r2,s1,s2r_1,r_2,s_1,s_2, the products p1a11τNLNRp_1a_{11}\tau N_LN_R and p2a22τCSLSRp_2a_{22}\tau CS_LS_R must be nonnegative. If either product is negative, there will exist a solution for r1,r2,r1,r2r_1,r_2,r_1,r_2 where the variables will be imaginary, which is disallowed in a Mueller matrix. This is the reason for the p1,p2p_1,p_2 variables that can take on the values ±1\pm1: they enforce the sign condition so that there exists real solutions for r1,r2,s1,s2r_1,r_2,s_1,s_2. The physical implications of such a matrix are unclear. The situation where either product is 0 is left to future work.

The solution to the system of equations reads

p1=sgn⁡[τa11NLNR](68)p_1=\operatorname{sgn}[\tau a_{11}N_LN_R] \tag*{(68)}
p2=sgn⁡[τCa22SLSR](69)p_2=\operatorname{sgn}[\tau Ca_{22}S_LS_R] \tag*{(69)}
r1=τNLp1a11NR,r2=sgn⁡[τa11]p1τNRa11NL(70)r_1=\sqrt{\frac{\tau N_L}{p_1a_{11}N_R}},\qquad r_2=\operatorname{sgn}\left[\frac{\tau}{a_{11}}\right]\sqrt{\frac{p_1\tau N_R}{a_{11}N_L}} \tag*{(70)}
s1=p2τCSLa22SR,s2=sgn⁡[τCa22]τCSRp2a22SL.(71)s_1=\sqrt{\frac{p_2\tau CS_L}{a_{22}S_R}},\qquad s_2=\operatorname{sgn}\left[\frac{\tau C}{a_{22}}\right]\sqrt{\frac{\tau CS_R}{p_2a_{22}S_L}}. \tag*{(71)}

Numerical simulations show that there are valid Mueller matrices that, when decomposed, correspond to an MspecialM_{\mathrm{special}} with (p1,p2)≠(1,1)(p_1,p_2)\ne(1,1): see Figure 2.

The final factorization reads

M=[u11/r1u12/s100u21/r1u22/s10000cos⁡2θ1sin⁡2θ100−sin⁡2θ1cos⁡2θ1]Mspecial(p1,p2)(τ,N,C,S,A,B)[v11/r2v12/r200v21/s2v22/s20000cos⁡2θ2sin⁡2θ200−sin⁡2θ2cos⁡2θ2].(72)M= \begin{bmatrix} u_{11}/r_1 & u_{12}/s_1 & 0 & 0 \\ u_{21}/r_1 & u_{22}/s_1 & 0 & 0 \\ 0 & 0 & \cos2\theta_1 & \sin2\theta_1 \\ 0 & 0 & -\sin2\theta_1 & \cos2\theta_1 \end{bmatrix} M_{\mathrm{special}}^{(p_1,p_2)}(\tau,N,C,S,A,B) \begin{bmatrix} v_{11}/r_2 & v_{12}/r_2 & 0 & 0 \\ v_{21}/s_2 & v_{22}/s_2 & 0 & 0 \\ 0 & 0 & \cos2\theta_2 & \sin2\theta_2 \\ 0 & 0 & -\sin2\theta_2 & \cos2\theta_2 \end{bmatrix}. \tag*{(72)}

Exchanging the second and fourth rows and columns to revert back to the original form of the Mueller matrix completes the decomposition.

References

  1. [1]Balakrishnan, P., Burnett, J., Chew, A., Dudley, C., Germer, T. A., Grantham, S. E., Moffitt, S. L., Barnes, B. M., Shirley, E. L., Sohn, M. Y., and Sunday, D. F., “An ultra-high vacuum ellipsometer for EUV Mueller matrix spectroscopic ellipsometry,” in [Metrology, Inspection, and Process Control XL], Schuch, N. G. and Cramer, H., eds., 13981, 139814Q, International Society for Optics and Photonics, SPIE (2026).DOI
  2. [2]Moffitt, S., Barnes, B. M., Germer, T. A., Grantham, S., Shirley, E. L., Sohn, M., Sunday, D., and Tarrio, C. S., “Instrument development for spectroscopic ellipsometry and diffractometry in the EUV,” International Conference on Frontiers of Characterization and Metrology for Nanoelectronics, Monterey, CA, US (2024-04-24 04:04:00 2024).
  3. [3]Chew, A., Barnes, B. M., Shirley, E. L., and Germer, T. A., “Ellipsometry in the EUV regime,” in [Metrology, Inspection, and Process Control XXXIX], Sendelbach, M. J. and Schuch, N. G., eds., 13426, 1342609, International Society for Optics and Photonics, SPIE (2025).
  4. [4]Tarrio, C., Grantham, S., Vest, R. E., Germer, T. A., Barnes, B. M., Moffitt, S. L., Simonds, B. J., and Spidell, M., “NIST efforts in extreme-ultraviolet metrology,” in [International Conference on Extreme Ultraviolet Lithography 2023], Nauleau, P. P., Gargini, P. A., Itani, T., and Ronse, K. G., eds., 12750, 127500F, International Society for Optics and Photonics, SPIE (2023).DOI
  5. [8]Devlaminck, V. and Terrier, P., “Definition of a parametric form of nonsingular Mueller matrices,” J. Opt. Soc. Am. A 25, 2636–2643 (Nov 2008).pubmed.ncbi.nlm.nih.gov/18978840
  6. [9]Simon, B. N., Simon, S., Mukunda, N., Gori, F., Santarsiero, M., Borghi, R., and Simon, R., “A complete characterization of pre-Mueller and Mueller matrices in polarization optics,” J. Opt. Soc. Am. A 27, 188–199 (Feb 2010).DOI
  7. [18]Bian, S., Xu, X., Cui, C., and Arteaga, O., “Calibration of achromatic fresnel rhombs with an elliptical retarder model in Mueller matrix ellipsometers,” Thin Solid Films 763, 139581 (2022).DOI
  8. [21]Arwin, H., Schoeche, S., Hilfiker, J., Hartveit, M., Järrendahl, K., Juárez-Rivera, O. R., Mendoza-Galyán, A., and Magnusson, R., “Optical chirality determined from Mueller matrices,” Applied Sciences 11(15) (2021).DOI
  9. [22]Kennedy, M. C. and O’Hagan, A., “Bayesian calibration of computer models,” Journal of the Royal Statistical Society. Series B (Statistical Methodology) 63(3), 425–464 (2001).DOI

Paper details

vlnc:W_rxky9gse
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents