betaFeedback

WorksEngineering

Data-Driven Output Regulation via Predictive Control

Abstract

This paper addresses constrained output regulation for unknown linear systems by means of predictive control directly from input-output data. The objective is to reject disturbances and track references generated by a known exosystem, without identifying a plant model or solving the output regulator equations. The first step is a trajectory parametrization for plants driven by exosignals with known dynamics. % By exploiting the known exosystem eigenstructure, Willems et al's fundamental lemma is extended from autonomous input-output trajectories to trajectories coupled with exogenous modes. By exploiting the known exosystem eigenstructure, input-output trajectories driven by an exosignal of known phase are parametrized directly from data, which contains the affine version of Willems et al.'s fundamental lemma as a special case. This parametrization yields a nominal data-driven predictive control (DDPC) regulator, for which a Lyapunov argument proves exponential convergence to the regulator manifold. For periodic exosignals, the steady-state feedforward input is eliminated from the online problem through an incremental-input regularization, leading to an implementable regulator based on measured data and known exosystem information. Bounded output noise is handled by slack and coefficient regularization, with a regularization center computed offline from data; the resulting robust DDPC law is recursively feasible and practically stabilizing, with an ultimate regulation error that vanishes with the noise bound. A constrained lateral vehicle-control example with periodic road curvature illustrates disturbance rejection, input-constraint satisfaction, and the transition from exact regulation with noise-free data to practical regulation with noisy data.

Introduction

Model predictive control (MPC) is powerful because it combines performance optimization with explicit constraint handling. Its success in process control, robotics, reinforcement learning, and autonomous motion planning has also motivated efforts to improve its computational efficiency [1]. Its effectiveness, however, relies on the availability of a predictive model that is accurate over the operating region of interest [2]. This modeling requirement becomes a bottleneck for systems whose dynamics are high-dimensional, strongly coupled, or repeatedly reconfigured. In such settings, deriving and maintaining a first-principles model can dominate the control-design effort, whereas input-output data are often readily available.

This work was supported by the Ministry of Education, Singapore, under AcRF Tier 1 Grant RG64/23, and the NTU-VinUni Joint Lab on Robotics and Embodied AI, and in part by the National Natural Science Foundation of China under Grants U23B2059 and 62688021. (Corresponding author: Lihua Xie)

Wenjie Liu is with the School of Electrical and Electronic Engineering, Nanyang Technological University, 639798, Singapore (e-mail: [email protected]).

Gang Wang is with the State Key Lab of Autonomous Intelligent Unmanned Systems, School of Automation, Beijing Institute of Technology, Beijing 100081, China (e-mail: [email protected]).

Lihua Xie is with the NTU–VinUni Joint Research Laboratory for Robotics and Embodied AI, School of Electrical and Electronic Engineering, Nanyang Technological University, Singapore 639798 and VinUniversity, Hanoi 100000, Vietnam (e-mail: [email protected]).

Data-driven predictive control (DDPC) has emerged as a principled way to reduce this modeling burden [3, 4]. A key enabler is Willems et al.’s fundamental lemma [5], which states that, under persistence of excitation, finite trajectories of an unknown linear system can be represented by linear combinations of previously measured trajectories. This observation has led to a set of MPC-like controllers with stability and robustness guarantees directly from data [6, 7, 8, 9, 10, 11, 12, 13]. Most existing DDPC results, nevertheless, are formulated around stabilization to a fixed equilibrium or tracking of equilibrium-like setpoints. Output regulation is different: the target behavior is an exosystem-driven trajectory on a regulator manifold, and the corresponding steady-state input is characterized by regulator equations that depend on the unknown plant.

Output regulation is the natural language for many constrained control tasks: grid converters must reject periodic load variations [14], vehicles must follow curvature-varying roads, and networked or robotic systems often have to synchronize with time-varying leaders. Classical solutions rely on the internal model principle and on solvability of the output regulator equations [15, 16, 17, 18]. These results are foundational, but their implementation typically requires plant matrices and feedforward regulator gains. When the plant is unknown or only measured through noisy input-output data, identifying a model and then solving the output regulator equations introduces an additional approximation layer precisely in the part of the design that determines the steady-state behavior.

Recent data-driven approaches to output regulation are compared in Table I. Most of them are feedback-synthesis results and do not handle input constraints [19, 20, 21, 22, 23], whereas DDPC formulations for repetitive tasks [24] lack closed-loop guarantees. Developing a constrained, data-driven predictive regulator with guarantees requires overcoming three obstacles. First, the Hankel prediction model must encode both the unknown plant response and the temporal structure induced by the known exosystem eigenstructure. Second, even with such a predictor, the usual equilibrium-centered DDPC stage cost is not aligned with the regulator manifold, since maintaining this manifold generally requires a nonzero feedforward input determined by the unknown regulator equations. Third, with noisy data, the coefficient regularization must be centered at the nonzero steady-state coefficient rather than at zero. These issues are addressed in the present paper.

We propose a predictive-control framework for data-driven output regulation of unknown linear systems driven by exogenous signals. The controller uses measured input-output trajectories, the exosystem dynamics, and online measurements; it does not identify the plant matrices and does not explicitly solve the classical output regulator equations. The analysis relies on the solvability of the output regulator equations, controllability/observability of the plant, a nonresonance condition, and incremental input-output-to-state stability of an auxiliary input-output realization. Under these standard structural conditions, the proposed receding-horizon laws steer the closed loop to the regulator manifold; under bounded output noise, they steer it to a neighborhood whose size is quantified by the noise level.

Data-drivenNo regulator equationsPredictive controlGuarantees with noisy dataExosignal information
MPC [25]×\times✓\checkmark✓\checkmark−-SS
[19, 20]✓\checkmark×\times×\times×\timesSS
[21]✓\checkmark✓\checkmark×\times✓\checkmarkSS
[22, 23]✓\checkmark✓\checkmark×\times✓\checkmarkSS
DeePRC [24]✓\checkmark✓\checkmark✓\checkmark×\timesTT
This paper✓\checkmark✓\checkmark✓\checkmark✓\checkmarkSS and phase

Table 1. Comparison with related output regulation approaches.

The main contributions are summarized as follows.

  • c1) A data-based parametrization of trajectories driven by exosignals with known dynamics and known phase, built on the decomposition in [23]; it recovers the affine fundamental lemma [9] for S=IS=I and comes with an excitation condition verifiable from the input and the exosystem basis.

  • c2) A constrained DDPC regulator that requires neither a plant model nor the regulator equations; for periodic exosignals, the steady-state feedforward input is removed by an incremental-input penalty.

  • c3) Recursive feasibility and exponential stability of the regulator manifold with noise-free data, and practical stability under noisy data and measurements, enabled by a regularization center computed offline from data with a guaranteed mismatch bound.

Notation. We denote the sets of real and complex numbers by R\mathbb{R} and C\mathbb{C}, respectively, and the sets of non-negative and positive integers by N\mathbb{N} and N+\mathbb{N}_{+}. For any matrix MM, M†M^\dagger denotes its Moore–Penrose pseudoinverse. The notation M≻(⪰)0M\succ(\succeq)0 indicates that MM is positive (semi-) definite, and similarly, M≺(⪯)0M\prec(\preceq)0 denotes that MM is negative (semi-) definite. For vector x∈Rnxx\in\mathbb{R}^{n_x}, ∥x∥\lVert x\rVert denotes its Euclidean norm, and for a matrix MM, ∥M∥\lVert M\rVert denotes the spectral norm. The minimum and maximum eigenvalues of matrix PP are denoted by λ‾P\underline{\lambda}_P and λ‾P\overline{\lambda}_P, respectively. For a signal x:N→Rnxx:\mathbb{N}\to\mathbb{R}^{n_x} and T∈N+T\in\mathbb{N}_{+}, the vectorized form of the signal xx over the interval [0,T−1][0,T-1] is denoted by x[0,T−1]:=[x(0)′ x(1)′⋯x(T−1)′]′x_{[0,T-1]}:=[x(0)^{\prime}\ x(1)^{\prime}\cdots x(T-1)^{\prime}]^{\prime}. The block-diagonal matrix with blocks A1,…,ANA_1,\ldots,A_N on its main diagonal is denoted block.diag⁡(A1,…,AN)\operatorname{block.diag}(A_1,\ldots,A_N). Given N,L∈N+N,L\in\mathbb{N}_{+}, the Hankel matrix of order LL of a length-NN trajectory x[0,N−1]x_{[0,N-1]} is denoted by HL(x[0,N−1]):=[x0x1⋯xN−Lx1x2⋯xN−L+1⋮⋮⋮xL−1xL⋯xN−1]H_L(x_{[0,N-1]}):=\begin{bmatrix}x_0&x_1&\cdots&x_{N-L}\\x_1&x_2&\cdots&x_{N-L+1}\\\vdots&\vdots&&\vdots\\x_{L-1}&x_L&\cdots&x_{N-1}\end{bmatrix}.

Fundamental Lemma for LTI Systems with Exosignals

This section establishes the data-based trajectory representation used throughout the paper. Consider the unknown linear system driven by an exosignal

wt+1=Swtxt+1=Axt+But+Ewtyt=Cxt+Fwt(1)\begin{aligned} w_{t+1} &= Sw_t \\ x_{t+1} &= Ax_t+Bu_t+Ew_t \\ y_t &= Cx_t+Fw_t \tag*{(1)} \end{aligned}

where xt∈Rnx_t\in\mathbb{R}^n is the state, ut∈Rmu_t\in\mathbb{R}^m is the control input, yt∈Rpy_t\in\mathbb{R}^p is the measured output, and wt∈Rnww_t\in\mathbb{R}^{n_w} represents disturbances or references generated by the exosystem. The plant matrices AA, BB, CC, EE, FF and the particular trajectory wtw_t are unknown, whereas the exosystem matrix SS and one input-output trajectory {ut,yt}t=0N−1\{u_t,y_t\}_{t=0}^{N-1} are available. If wt=0w_t=0, Willems et al’s fundamental lemma [5] states that, under controllability and persistence of excitation, a candidate sequence {uˉt,yˉt}t=0L−1\{\bar{u}_t,\bar{y}_t\}_{t=0}^{L-1} is a valid trajectory if and only if there exists g∈RN−L+1g\in\mathbb{R}^{N-L+1} satisfying

\begin{bmatrix} H_L(u_{[0,N-1]})\\ H_L(y_{[0,N-1]}) \end{bmatrix}g= \begin{bmatrix} \bar{u}\\ \bar{y} \end{bmatrix}. \tag*{(2)}\end{bmatrix}

For constant offsets, i.e., S=IS=I, [9 Theorem 1] accounts for the exogenous component by imposing the affine constraint ∑i=0N−Lgi=1\sum_{i=0}^{N-L}g_i=1. Dynamic exosignals require a different treatment: the contribution of wtw_t cannot in general be separated from the measured input-output data, but its temporal structure is known through SS. The following decomposition converts exosystem trajectories into a finite set of known basis signals with unknown coefficients.

Lemma 1 ([23 Lemmas 3.3–3.4]). Consider any exosignal sequence {wt}t=0N−1\{w_t\}_{t=0}^{N-1} generated by (1a) with initial condition w0∈Rnww_0\in\mathbb{R}^{n_w}. Then, for H1(w):=[w0 w1 ⋯ wN−L]H_1(w):=[w_0\ w_1\ \cdots\ w_{N-L}], there exist an integer nM≤nwn_M\le n_w, a matrix L(w0)∈RnM×N\mathcal{L}(w_0)\in\mathbb{R}^{n_M\times N} and known vectors M(i)∈RnM\mathcal{M}(i)\in\mathbb{R}^{n_M}, i=0,…,N−Li=0,\ldots,N-L, such that

H1(w)=L(w0)[M(0) M(1) ⋯ M(N−L)]=L(w0)H1(M)(3)H_1(w)=\mathcal{L}(w_0)[\mathcal{M}(0)\ \mathcal{M}(1)\ \cdots\ \mathcal{M}(N-L)]=\mathcal{L}(w_0)H_1(\mathcal{M}) \tag*{(3)}

where H1(M)∈RnM×(N−L+1)H_1(\mathcal{M})\in\mathbb{R}^{n_M\times(N-L+1)} is known and of full row rank.

References

  1. [1]Z. Hou, F. Zhao, and K. You, “Harnessing data for accelerating model predictive control by constraint removal,” in Proc. IEEE Conf. Decis. Control, Milan, Italy, Dec. 16–19 2024, pp. 285–290.arxiv.org/abs/2403.19126
  2. [2]J. B. Rawlings, D. Q. Mayne, and M. M. Diehl, Model Predictive Control: Theory and Design, 2nd ed. Nob Hill Publishing, 2019.
  3. [3]F. Dörfler, J. Coulson, and I. Markovsky, “Bridging direct and indirect data-driven control formulations via regularizations and relaxations,” IEEE Trans. Autom. Control, vol. 68, no. 2, pp. 883–897, 2022.
  4. [4]G. Wang, W. Liu, Y. Li, X. Wang, J. Sun, and J. Chen, “Data-driven control of network systems: Accounting for communication adaptivity and security,” Sci. China Inf. Sci., vol. 69, no. 2, p. 121201, 2026.arxiv.org/abs/2511.15044
  5. [5]J. C. Willems, J. M. Rapisarda, and B. L. De Moor, “A note on persistency of excitation,” Syst. Control Lett., vol. 54, no. 4, pp. 325–329, Apr. 2005.
  6. [6]J. Berberich, J. Köhler, M. A. Müller, and F. Allgöwer, “Data-driven model predictive control with stability and robustness guarantees,” IEEE Trans. Autom. Control, vol. 66, no. 4, pp. 1702–1717, Apr. 2021.DOI
  7. [7]J. Bongard, J. Berberich, J. Köhler, and F. Allgöwer, “Robust stability analysis of a simple data-driven model predictive control approach,” IEEE Trans. Autom. Control, vol. 68, no. 5, pp. 2625–2637, 2022.DOI
  8. [8]W. Liu, J. Sun, G. Wang, F. Bullo, and J. Chen, “Data-driven resilient predictive control under denial-of-service,” IEEE Trans. Autom. Control, vol. 68, no. 8, pp. 4722–4737, Aug. 2023.arxiv.org/abs/2110.12766
  9. [9]J. Berberich, J. Köhler, M. A. Müller, and F. Allgöwer, “Linear tracking MPC for nonlinear systems Part II: The data-driven case,” arXiv:2105.08567, 2021.DOI
  10. [10]A. Chiuso, M. Fabris, B. Breschi, and S. Formentin, “Harnessing uncertainty for a separation principle in direct data-driven predictive control,” Automatica, vol. 173, p. 112070, 2025.
  11. [11]L. Huang, J. Zhen, J. Lygeros, and F. Dörfler, “Robust data-enabled predictive control: Tractable formulations and performance guarantees,” IEEE Trans. Autom. Control, vol. 68, no. 5, pp. 3163–3170, 2023.
  12. [12]Y. Xie, J. Berberich, and F. Allgöwer, “Data-driven min–max MPC for linear systems: Robustness and adaptation,” Automatica, vol. 183, p. 112612, 2026.
  13. [13]M. Alsalti, M. Barkey, V. G. Lopez, and M. A. Müller, “Robust and efficient data-driven predictive control,” Automatica, vol. 191, p. 113108, 2026.DOI
  14. [14]W. Liu, M. Zhang, Q. Xu, and L. Xie, “Survey on data-driven control and its application in cyber-physical energy systems,” Cyber-Physical Energy Systems, vol. 1, no. 1, pp. 28–48, Nov. 2025.DOI
  15. [15]W. M. Monahan, Linear Multivariable Control. Springer-Verlag New York Berlin Heidelberg Tokyo, 1974, vol. 101.
  16. [16]B. A. Francis and W. M. Wonham, “The internal model principle of control theory,” Automatica, vol. 12, no. 5, pp. 457–465, Sept. 1976.DOI
  17. [17]E. Davison, “The robust control of a servomechanism problem for linear time-invariant multivariable systems,” IEEE Trans. Autom. Control, vol. 21, no. 1, pp. 25–34, Feb. 1976.DOI
  18. [18]H. Zhou, Nonlinear Output Regulation: Theory and Applications. SIAM, 2004.
  19. [19]J. Jiao, H. J. van Waarde, H. L. Trentelman, M. K. Çamlıbel, and S. Hirche, “Data-driven output synchronization of heterogeneous leader-follower multi-agent systems,” in Proc. IEEE Conf. Decis. Control, Austin, TX, USA, Dec. 2021, pp. 466–471.arxiv.org/abs/2103.11851
  20. [20]L. Zhu and Z. Chen, “Data informativity for robust output regulation,” IEEE Trans. Autom. Control, vol. 69, no. 10, pp. 7075–7080, Oct. 2024.DOI
  21. [21]Y. Li, W. Liu, G. Wang, J. Sun, L. Xie, and J. Chen, “Data-driven polytopic output synchronization from noisy data,” IEEE Trans. Autom. Control, vol. 69, no. 12, pp. 8513–8525, 2024.
  22. [22]W. Liu, Y. Li, J. Sun, G. Wang, K. You, L. Xie, and J. Chen, “Data-driven internal model control for output regulation,” IEEE Trans. Cybern., pp. 1–14, 2026.DOI
  23. [23]A. Bisoffi, W. Liu, Z. Hu, and C. De Persis, “Output regulation via input-output data,” arXiv preprint arXiv:2605.22562, 2026.arxiv.org/abs/2605.22562
  24. [24]R. Dinkla, T. Oomen, S. P. Mulders, and J.-W. van Wingerden, “Data-enabled predictive repetitive control,” in Proc. IEEE Conf. Decis. Control, Milan, Italy, 2024, pp. 6749–6754.arxiv.org/abs/2408.15210
  25. [25]J. Köhler, M. A. Müller, and F. Allgöwer, “Constrained nonlinear output regulation using model predictive control,” IEEE Trans. Autom. Control, vol. 67, no. 5, pp. 2419–2434, 2021.DOI
  26. [26]D. A. Allan and J. B. Rawlings, “A Lyapunov-like function for full information estimation,” in Amer. Control Conf. Philadelphia, PA, USA: IEEE, 2019, pp. 4497–4502.DOI
  27. [27]J. M. Snider, “Automatic steering methods for autonomous automobile path tracking,” Robotics Institute, Pittsburgh, PA, Tech. Rep. CMU-RITR-09-08, 2009.
  28. [28]R. Zuliani, E. C. Balta, and J. Lygeros, “Policy optimization with differentiable MPC: Convergence analysis under uncertainty,” arXiv preprint arXiv:2601.01940, 2026.arxiv.org/abs/2601.01940

Paper details

vlnc:W_s28a6fpu
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Engineering

Not recorded for this paper

View statement
Looking for related papers…
Contents