betaFeedback

WorksPhysics and Astronomy

Synchronous control study of Chua circuit system via capacitive closed-loop coupling

Abstract

Synchronous control of nonlinear circuits is of great importance in many fields. In this paper, a capacitor is used for closed-loop coupling of three dual-vortex attractor Chua circuits with the same circuit parameters and different initial conditions, and the corresponding synchronization processes and synchronization effects are investigated. It is found that, for the capacitor, the closed-loop coupling can completely synchronize the three Chua circuits. And there exists a critical coupling strength δcriticalCδ_{critical}^C that can be calculated, and when the coupling strength is between the critical coupling strength δcriticalCδ_{critical}^C and the upper coupling strength δmaxCδ_{max}^C, the three circuits can be completely synchronized very quickly. Moreover, the results show that the unidirectional coupling cannot make the circuit system completely synchronized. Finally, we also verify the correctness of the calculation by circuit simulation experiments.

Introduction

In traditional circuit theory, circuits are usually classified into two main categories: linear and nonlinear circuits. In fact there is no strictly linear circuit, it only appears to be approximately linear around a specific operating point. Therefore, the study of nonlinear circuits is particularly important. A nonlinear circuit is a circuit containing nonlinear components. With the development of electronics, many highly nonlinear electronic devices have emerged, such as amnesic resistors [1, 2], nonlinear diodes [3], and so on. This makes the nonlinear circuits composed by these devices widely used in electronic circuits, and also makes a large number of nonlinear phenomena appear in electronic circuits, such as self-excited oscillations, probable periodic motion [4] and chaos [5, 6]. So are these nonlinear phenomena beneficial or harmful in practical use? Does it have any exploitable value? Take chaotic phenomena as an example, the unpredictability and initial value sensitivity of chaotic systems make it difficult to fully control chaotic phenomena. However, the control of chaotic phenomena can be applied to many scenarios, such as secure communication [7], information processing[8], and even biological neuronal analysis[9, 10, 11] in which would like to control chaotic phenomena. L. M. Pecora and T. L. Carroll proposed a method for analyzing identical chaotic systems using principal stability functions [12, 13, 14]. Chua circuits a simple nonlinear electronic circuit design which can exhibit standard chaos theory behavior[15]. The Chua circuit can be accurately modeled mathematically and is considered as a ”paradigm of chaotic systems”. Therefore, it may be a good choice to start from the synchronous control of Chua circuits to further study chaotic control.

In recent years, many approaches to the control of Chua circuits have been proposed. As the founders of Chua circuits, L. O. Chua et al. first investigated the synchronization between Chua circuits experimentally[16]. Chaotic control by time lag feedback controller[17] and adaptive feedback controller [18]is also the mainstream control method nowadays. By improving the basic Chua circuit and studying the pulse synchronization and phase synchronization in it[19, 20], derived some methods to make the Chua circuit self-regulating. In practice, most nonlinear circuit models are in the form of systems, and a Chua circuit can only be considered as a unit in a system. Therefore, by activating coupling channels between different circuit modules, they can be regulated to each other. This approach would be more relevant to the real scenario.

Based on this idea, Ref. [21] successfully achieved simultaneous regulation of two Chua by activating a capacitive coupling channel between two Chua circuits and exploiting the feature of capacitors to store energy. Similarly, Ref. [22] investigated the synchronization between two chua circuits coupled through an inductor; Ref. [23] investigated the synchronization between two chua circuits coupled through a thermistor. It was found that these nonlinear components have a good modulation effect between both chua circuits, and the concept of coupling strength was given to characterize the magnitude of the coupling ability between two circuits by different components [21, 22, 23]. More complex, the same control can be achieved by coupling through amnesic resistors or other combinations of nonlinear elements [24, 25, 26]. With these research foundations, Ref. [27] studied the synchronization of a circuit system consisting of fifty Chua circuits with different nonlinear elements coupled unidirectionally. The results show that the coupling strengths corresponding to different elements vary considerably in value and that the coupling strength directly determines the synchronization effect between circuits. For systems where the number of circuits to be coupled is greater than or equal to three, the control method is divided into open-loop control (no feedback control) or feedback control for implementation. The previously mentioned unidirectional coupling becomes a kind of feedback-free control. In fact, in contrast to feedback-free control, feedback control allows the system state to move away from chaotic motion and into an arbitrary desired immobility point. This makes it easier to synchronize the multi-circuit system completely. Therefore, our work builds on the former study and proposes and computationally proves a closed-loop coupling of multiple nonlinear circuits using the basic idea of feedback control. The main body of this paper is divided into the following parts: First, in Sec. II, we start with a basic Chua circuit, which is identically coupled to three chua circuits by capacitive closed-loop. And the corresponding circuit equations as well as the dimensionless equations are given. The parameters chosen for subsequent calculations are also given. Second, in Sec. III, we fix the Chua circuit parameters and give the initial conditions for each of the three Chua circuits to be impassable. Based on this, we calculated the synchronization process and synchronization effect of the circuits when they are connected through the closed-loop capacitor, by adjusting the values of the coupling strength between the circuits. And the results are compared with the synchronization results of unidirectional coupling, and the advantages of closed-loop coupling are derived. In Sec. IV, we build a simulation circuit and observe the experimental results to further prove the feasibility of the theory and the numerical realism. Finally, a summary is given in Sec. V.

Circuit model

Chua circuit and parameter selection

Chua circuits are the simplest class of nonlinear circuits with the circuit equation:

{C1dVC1dt=VC2−VC1R−f(VC1)C2dVC2dt=VC1−VC2R+iLLdiLdt=−VC2(1)\begin{cases} C_{1}\frac{dV_{C1}}{dt}=\frac{V_{C2}-V_{C1}}{R}-f(V_{C1})\\ C_{2}\frac{dV_{C2}}{dt}=\frac{V_{C1}-V_{C2}}{R}+i_{L}\\ L\frac{di_{L}}{dt}=-V_{C2} \tag*{(1)} \end{cases}

where

f(VC)=GaVC+0.5(Ga−Gb)(∣VC+E∣−∣VC−E∣)(2)f(V_{C})=G_{a}V_{C}+0.5(G_{a}-G_{b})(|V_{C}+E|-|V_{C}-E|) \tag*{(2)}

is the characteristic function of the Chua nonlinear diode. where GaG_{a}, GbG_{b}, and EE are constants, all of which are characteristic properties of the element itself. By the proportional transformation of the Chua circuit [28]

x=VC1E,y=VC2E,z=iLRE,τ=tRC2x=\frac{V_{C1}}{E},y=\frac{V_{C2}}{E},z=\frac{i_{L}R}{E},\tau=\frac{t}{RC_{2}}
m0=RGa,m1=RGb,α=C2C1,β=C2R2L(3)m_{0}=RG_{a},m_{1}=RG_{b},\alpha=\frac{C_{2}}{C_{1}},\beta=\frac{C_{2}R^{2}}{L} \tag*{(3)}

The dimensionless kinetic equations of a single Chua circuit can be obtained [15]

{x˙=α[y−x−f(x)]y˙=x−y−zz˙=−βy(4)\begin{cases} \dot{x}=\alpha[y-x-f(x)]\\ \dot{y}=x-y-z\\ \dot{z}=-\beta y \tag*{(4)} \end{cases}

where

f(x)=m1x+0.5(m0−m1)(∣x+1∣−∣x−1∣)(5)f(x)=m_{1}x+0.5(m_{0}-m_{1})(|x+1|-|x-1|) \tag*{(5)}

The parameters of the Chua circuit are chosen as[16]

C1=10nF,C2=100nF,E=1V,L=18.75mHC_{1}=10\mathrm{nF},C_{2}=100\mathrm{nF},E=1\mathrm{V},L=18.75\mathrm{mH}
G=1R=0.599mS,Ga=−0.76mS,Gb=−0.41mS(6)G=\frac{1}{R}=0.599\mathrm{mS},G_{a}=-0.76\mathrm{mS},G_{b}=-0.41\mathrm{mS} \tag*{(6)}

The corresponding dimensionless parameters are

α=10,β=14.87,a=−1.27,b=−0.68(7)\alpha=10,\beta=14.87,a=-1.27,b=-0.68 \tag*{(7)}

A set of parameters such as these triggers the chaos of the Chua circuit, and our subsequent calculations, simulations, and discussions are based on these parameters.

In the subsequent study, We will discuss the closed-loop coupling of the "xx" outputs of the three Chua circuits through capacitors and discuss the synchronization process between the circuits.

Capacitive Closed-loop Coupling

First, the three Chua circuits are closed-loop coupled through capacitor CcC_{c} (Figure 1). The circuit equation is:

Figure 1. Capacitive closed-loop coupling three Chua circuit schematic

{C11dVC11dt=VC12−VC11R1−f(VC11)+i1C−i3CC12dVC12dt=VC12−VC1R1+iL1L1diL1dt=−VC12C21dVC21dt=VC22−VC21R2−f(VC21)+i2C−i1CC22dVC22dt=VC22−VC2R2+iL2L2diL2dt=−VC22C31dVC31dt=VC32−VC31R3−f(VC31)+i3C−i2CC32dVC32dt=VC32−VC3R3+iL3L3diL3dt=−VC32(8)\begin{cases} C_{11}\frac{dV_{C11}}{dt}=\frac{V_{C12}-V_{C11}}{R_{1}}-f(V_{C11})+i_{1}^{C}-i_{3}^{C}\\ C_{12}\frac{dV_{C12}}{dt}=\frac{V_{C12}-V_{C1}}{R_{1}}+i_{L1}\\ L_{1}\frac{di_{L1}}{dt}=-V_{C12}\\ C_{21}\frac{dV_{C21}}{dt}=\frac{V_{C22}-V_{C21}}{R_{2}}-f(V_{C21})+i_{2}^{C}-i_{1}^{C}\\ C_{22}\frac{dV_{C22}}{dt}=\frac{V_{C22}-V_{C2}}{R_{2}}+i_{L2}\\ L_{2}\frac{di_{L2}}{dt}=-V_{C22}\\ C_{31}\frac{dV_{C31}}{dt}=\frac{V_{C32}-V_{C31}}{R_{3}}-f(V_{C31})+i_{3}^{C}-i_{2}^{C}\\ C_{32}\frac{dV_{C32}}{dt}=\frac{V_{C32}-V_{C3}}{R_{3}}+i_{L3}\\ L_{3}\frac{di_{L3}}{dt}=-V_{C32} \tag*{(8)} \end{cases}

The current through the coupling capacitor is i1Ci_{1}^{C}, i2Ci_{2}^{C}, i3Ci_{3}^{C}. Since the capacitor will continuously show charge and discharge in the circuit, it is also called feedback current. The capacitor will apply an feedback current on the Chua circuit to which it is connected. The specific form is:

{i1C=CC1(V˙C21−V˙C11)i2C=CC2(V˙C31−V˙C21)i3C=CC3(V˙C11−V˙C31)(9)\begin{cases} i_{1}^{C}=C_{C1}(\dot{V}_{C21}-\dot{V}_{C11})\\ i_{2}^{C}=C_{C2}(\dot{V}_{C31}-\dot{V}_{C21})\\ i_{3}^{C}=C_{C3}(\dot{V}_{C11}-\dot{V}_{C31}) \tag*{(9)} \end{cases}

where CCkC_{Ck}, (k=1,2,3k=1,2,3) is the capacitance of the coupling capacitor. Similarly, the dimensionless equation for a system coupled through a closed-loop capacitor can be obtained by the dimensional transformation Eq. (3).

{x˙1=α1[y1−x1−f(x1)]+δ1C(x˙2−x˙1)−δ3C(x˙1−x˙3)y˙1=x1−y1−z1z˙1=−β1y1x˙2=α2[y2−x2−f(x2)]+δ2C(x˙3−x˙2)−δ1C(x˙2−x˙1)y˙2=x2−y2−z2z˙2=−β2y2x˙3=α3[y3−x3−f(x3)]+δ3C(x˙1−x˙3)−δ2C(x˙3−x˙2)y˙3=x3−y3−z3z˙3=−β3y3(10)\begin{cases} \dot{x}_{1}=\alpha_{1}[y_{1}-x_{1}-f(x_{1})]+\delta_{1}^{C}(\dot{x}_{2}-\dot{x}_{1})-\delta_{3}^{C}(\dot{x}_{1}-\dot{x}_{3})\\ \dot{y}_{1}=x_{1}-y_{1}-z_{1}\\ \dot{z}_{1}=-\beta_{1}y_{1}\\ \dot{x}_{2}=\alpha_{2}[y_{2}-x_{2}-f(x_{2})]+\delta_{2}^{C}(\dot{x}_{3}-\dot{x}_{2})-\delta_{1}^{C}(\dot{x}_{2}-\dot{x}_{1})\\ \dot{y}_{2}=x_{2}-y_{2}-z_{2}\\ \dot{z}_{2}=-\beta_{2}y_{2}\\ \dot{x}_{3}=\alpha_{3}[y_{3}-x_{3}-f(x_{3})]+\delta_{3}^{C}(\dot{x}_{1}-\dot{x}_{3})-\delta_{2}^{C}(\dot{x}_{3}-\dot{x}_{2})\\ \dot{y}_{3}=x_{3}-y_{3}-z_{3}\\ \dot{z}_{3}=-\beta_{3}y_{3} \tag*{(10)} \end{cases}

where δ1C\delta_1^{C}, δ2C\delta_2^{C}, δ3C\delta_3^{C} is the coupling constant at capacitive coupling, defined as [21]

δkC=CckCk1+2Cck,k=1,2,3(11)\delta_k^{C} = \frac{C_{ck}}{C_{k1}+2C_{ck}}, \qquad k=1,2,3 \tag*{(11)}

The value of the capacitive coupling strength is changed by changing the value of the capacitance at the output of the Chua circuit and the value of the coupling capacitance. And the feedback current itself is also time-varying. Also, the strength of the coupling directly determines whether the circuits can be synchronized with each other.

Next, we will discuss in detail the synchronization process between the three Chua circuits when they are closed-loop coupled through capacitors.

Numerical results

Synchronous Control Function Discussion

The output, oscillations and nonlinearities of the Chua circuit can be adjusted by setting different parameters with initial conditions for the set of dimensionless equations. In the subsequent discussion, we uniformly choose the parameters in Eq. (7) as the coefficients in the dimensionless equations. Such a set of parameters allows the Chua circuit to excite a double vortex attractor as shown in Figure 2. Using the control variables, we set different initial conditions for the three Chua circuits discussed, as follows: [x1(0),y1(0),z1(0)]=[0.5,0.1,0.1][x_1(0),y_1(0),z_1(0)] = [0.5,0.1,0.1], [x2(0),y2(0),z2(0)]=[0.1,0.5,0.1][x_2(0),y_2(0),z_2(0)] = [0.1,0.5,0.1], [x3(0),y3(0),z3(0)]=[0.1,0.1,0.5][x_3(0),y_3(0),z_3(0)] = [0.1,0.1,0.5]

Figure 2. Dual vortex attractor of Chua circuit with parameter set to Eq. (7).

First, we discuss whether the three Chua circuits can be synchronized when they are closed-loop coupled using different energy storage elements. We use the error function between the two circuits to characterize the degree of synchronization between them. The error function is defined as [29, 30]:

Eij=(xi−xj)2+(yi−yj)2+(zi−zj)2(12)E_{ij} = \sqrt{(x_i-x_j)^2+(y_i-y_j)^2+(z_i-z_j)^2} \tag*{(12)}

where ii, jj is the ordinal number of the two different Chua circuits and i≠ji \ne j. EijE_{ij} denotes the synchronization error between the ii-th circuit and the jj-th circuit. We consider that the two Chua circuits are fully synchronized when Eij→0E_{ij} \to0. The three Chua circuits as a whole reach complete synchronization when every two circuits are synchronized with each other.

For capacitive closed-loop coupling of the three Chua circuits. First we set the coupling strength δ1C=δ2C=δ3C=0.1\delta_1^{C} = \delta_2^{C} = \delta_3^{C} = 0.1. The corresponding capacitance value of the coupling capacitor Cc1=Cc2=Cc3=1.25C_{c1} = C_{c2} = C_{c3} = 1.25 nF. The error evolution between the three circuits at this point is shown in Figure 3.

Figure 3. The evolution of synchronization error between circuits coupled by closed-loop capacitance for coupling strength δ1C=δ2C=δ3C=0.1\delta^{C}_{1}=\delta^{C}_{2}=\delta^{C}_{3}=0.1.

It can be seen that the closed-loop coupling of capacitor with a capacitance value of 1.25nF (δ3C=0.1\delta_3^{C} = 0.1) does not allow the three Chua circuits to be fully synchronized. However, when we set the coupling strengths δ1C=δ2C=δ3C=0.2\delta_1^{C} = \delta_2^{C} = \delta_3^{C} = 0.2 (Cc1=Cc2=Cc3=3.33C_{c1} = C_{c2} = C_{c3} = 3.33 nF) and δ1C=δ2C=δ3C=0.4\delta_1^{C} = \delta_2^{C} = \delta_3^{C} = 0.4 (Cc1=Cc2=Cc3=20C_{c1} = C_{c2} = C_{c3} = 20 nF), the error evolution is shown in Figure 4. Eventually the error function between each two circuits tends to zero. At this point we then consider that the three Chua circuits can be fully synchronized at coupling strengths δC=0.2\delta^{C} = 0.2 and δC=0.4\delta^{C} = 0.4.

Figure 4. (A),(B),(C) is the evolution of synchronization error between circuits at δ1C=δ2C=δ3C=0.2\delta_1^C=\delta_2^C=\delta_3^C=0.2; (D),(E),(F) is the evolution of synchronization error between circuits at δ1C=δ2C=δ3C=0.4\delta_1^C=\delta_2^C=\delta_3^C=0.4.

However, is there a threshold coupling strength that can exactly synchronize the three Chua circuits coupled through the closed loop of capacitance? The answer is yes. We calculated the maximum sum of errors ∑EMax\sum E_{Max} of the system in a certain time series and found this threshold coupling strength δcriticalC\delta^{C}_{critical} (Figure 5). It was also found that the value of this threshold coupling strength varies with the change of circuit parameters and initial conditions. That is, for different Chua circuits, the threshold coupling strength that will enable them to be fully synchronized will be different. In this paper, we choose a Chua circuit corresponding to a threshold coupling strength δcriticalC=0.2\delta^{C}_{critical}=0.2. However, for capacitive coupling, the upper limit of the coupling strength is limited by Eq. (11). The maximum value of the coupling strength for capacitive coupling is δmaxC=lim⁡Cc→∞=0.5\delta^{C}_{max}=\lim_{C_{c}\to\infty}=0.5 (Figure 6). Therefore, when δC∈[δcriticalC,δmaxC]\delta^{C}\in[\delta^{C}_{critical},\delta^{C}_{max}] is selected, the three Chua circuits can be completely synchronized; when δC∈[0,δcriticalC]\delta^{C}\in[0,\delta^{C}_{critical}] is selected, the three Chua are not completely synchronized.

Figure 5. The relationship between the maximum error ∑EMax\sum E_{\mathrm{Max}} and the coupling strength δcriticalC\delta_{\mathrm{critical}}^C for a system in a given time series. The green solid line corresponds to the parameter [7] of the Chua circuit chosen in this paper; The red dashed line corresponds to the change of β=14.87\beta=14.87 to β=16\beta=16 in the original parameter; The blue dotted line corresponds to the change of the original initial condition to [x1(0),y1(0),z1(0)]=[0.5,0.5,0.5][x_1(0),y_1(0),z_1(0)]=[0.5,0.5,0.5].

Figure 6. The variation pattern of the capacitive coupling strength with the value of the coupling capacitance. It is noted that, regardless of the value of the capacitance Ck1C_{k1} at the output, as the value of the coupling capacitance CcC_c increases, the maximum value of the coupling strength is δmax⁡C=0.5\delta_{\max}^C=0.5.

In fact, when we couple three Chua circuits by closed-loop capacitance. If one of the coupling strengths does not reach the synchronization threshold, we can also make the three circuits fully synchronized by appropriately adjusting the other coupling strength parameters. For example, we set the coupling strength to [δ1C,δ2C,δ3C]=[0.1,0.4,0.45][\delta^{C}_{1},\delta^{C}_{2},\delta^{C}_{3}]=[0.1,0.4,0.45], where δ1C<δcriticalC\delta^{C}_{1}<\delta^{C}_{critical}. However, the error evolution diagram (Figure 7) shows that the three Chua circuits are eventually synchronized in the same short time. This is something that cannot be done with unidirectional coupling.

Figure 7. Special result for capacitive closed-loop coupling: there is a coupling strength that does not reach the synchronizable coupling strength threshold δcriticalC\delta^{C}_{critical} (The coupling strengths are [δ1C,δ2C,δ3C]=[0.1,0.4,0.45][\delta^{C}_{1},\delta^{C}_{2},\delta^{C}_{3}] = [0.1, 0.4, 0.45], and δ1C=0.1<δcriticalC\delta^{C}_{1} = 0.1 < \delta^{C}_{critical}).

Closed-loop Coupling Advantage Analysis

We consider three Chua circuits with the same circuit parameters and different initial conditions (same parameters and initial states as discussed in Sec. III A). All three Chua circuits are in a chaotic state and can excite a double vortex attractor. We use capacitors for one-way and closed-loop coupling of the three Chua circuits, and discuss the synchronization of the three circuits under different coupling methods. For the subsequent discussion. The coupling strengths we have chosen are the same, i.e., δ1C=δ2C=δ3C=δC\delta^{C}_{1}=\delta^{C}_{2}=\delta^{C}_{3}=\delta^{C}.

We discuss the unidirectional coupling and Closed-loop coupling of the three Chua circuits using capacitors, respectively. We all set the coupling strengths to δC=0.3\delta^{C}=0.3 and δC=0.48\delta^{C}=0.48, respectively, and the circuit coupling error evolution diagram is shown in Figure 9 and Figure 10.

Figure 9. For the same three Chua circuits, at the same coupling strength δC=0.3\delta^{C}=0.3. (A), (B), (C) is the synchronization error between circuits when coupled unidirectionally through capacitors; (D), (E), (F) is the synchronization error between circuits when coupled closed-loop through capacitors.

Figure 10. For the same three Chua circuits, at the same coupling strength δC=0.48\delta^{C}=0.48. (A), (B), (C) is the synchronization error between circuits when coupled unidirectionally through capacitors; (D), (E), (F) is the synchronization error between circuits when coupled closed-loop through capacitors.

For δC=0.3\delta^{C}=0.3, it is completely impossible to synchronize the three circuits (see Figure 9 (A) , (B) , (C)); For δC=0.48\delta^{C}=0.48, it is only possible to achieve a state of approximate synchronization between some two circuits in part of the time period, but there is still a certain error (see Figure 10 (A) , (B) , (C)). And this approximate synchronization does not last long, after which it becomes unsynchronized again. Because of the limitation of the definition of capacitor coupling strength, δC<δmax⁡C=0.5\delta^C < \delta_{\max}^C = 0.5. Therefore, we can assume that the unidirectional coupling of the capacitor cannot fully synchronize the three Chua circuits. Similarly, we have calculated the sum of the maximum system errors ∑EMax\sum E_{\mathrm{Max}} for unidirectional coupling (Figure 8). the results show that when coupling the Chua circuits unidirectionally through capacitors, they cannot be perfectly synchronized, no matter how large the value of the coupling capacitance is taken.

Figure 8. The trend of the maximum system error with the coupling strength for unidirectional coupling. The total error is always oscillating and does not converge to zero. Therefore unidirectional coupling does not synchronize the three Chua circuits.

When using the capacitor closed-loop coupling of the three Chua circuits, we choose the same parameters δC=0.3\delta^C=0.3 and

δC=0.48\delta^{C}=0.48. The synchronization case is shown in Figure 9 (D), (E), (F) and Figure 10 (D), (E), (F). It can be seen that both coupling strengths can fully synchronize the three Chua circuits. In fact, we have calculated in Sec. III A that for a system of Chua circuits coupled by closed-loop capacitors, the entire circuit system can be fully synchronized when the coupling strength satisfies δC>δcriticalC\delta^{C}>\delta^{C}_{critical}. The critical value of the coupling strength dd depends on the basic circuit parameters of the selected Chua circuit.

Thus, the advantage of closed-loop coupling is, If the available circuit elements are limited to capacitors, the unidirectional coupling does not allow more than two Chua circuits to be fully synchronized. With closed-loop coupling, the entire circuit system can be fully synchronized with a smaller capacitance, and the overall efficiency is much higher than with one-way coupling.

This is because the closed-loop coupling is essentially an additional negative feedback loop compared to the unidirectional coupling. The Chua circuit itself has nonlinear characteristics, and the negative feedback loop can reduce the degree

of nonlinearity of the system by adjusting the voltage or current to make it more stable. Without the negative feedback loop, the system consisting of three Chua circuits would be an unstable system, with the frequency and amplitude of the output signal varying over time. However, when a negative feedback loop is added, the frequency and amplitude of the output signal can be controlled by adjusting the feedback coefficient to stabilize it around a specific value. Specifically, the negative feedback loop compares the output signal of the chaotic circuit with the input signal, then amplifies the difference and inputs it back into the chaotic circuit. This feedback action suppresses the instability of the chaotic circuit and stabilizes its output signal within a specific range.

Circuit Simulation Experiment

In the previous discussion, we calculated the numerical results of synchronous control of three Chua circuits using capacitive closed-loop coupling. In this section, we will further verify the synchronization between the Chua circuits through simulation experiments.

We use the circuit simulation software to build the simulation diagrams of the three Chua circuits via capacitive closed-loop coupling (see Appendix § 1.2.1).The circuit component parameters are chosen as Eq. (7). The results of the circuit simulation are shown in Figure 13 It is confirmed that the Chua circuit is chaotic and can excite the double vortex attractor at this parameter.

Attractor evolution diagram in simulation

Figure 13. Attractor evolution diagram in simulation

Afterwards, we observe the synchronization of the three circuits. When coupling by capacitance, the coupling capacitance Cc=3.33nFC_c = 3.33\mathrm{nF} is chosen and the time series of the xx outputs of the three circuits are observed using a four-channel oscilloscope (see Figure 12). It can be seen that the three curves gradually overlap, which also means that the three Chua circuits gradually become fully synchronized. We can also numerically calculate the time series at the xx output. The coupling capacitance Cc=3.33 nFC_c = 3.33\ \mathrm{nF} corresponds to the coupling strength δC=0.2\delta^{C} = 0.2, and the numerical results are shown in Figure 11 The numerical results are in general agreement with the experimental results.

Figure 11. The time series evolution of the output of the “x” side of the Chua circuit is plotted. The results show that the time series of the three circuits do not coincide at the beginning due to the different initial values we set for the circuits. However, as time goes on, the outputs of the “x” side of the three circuits gradually coincide, which also means that the three Chua circuits are synchronized.

Voltage output time series in simulation

Figure 12. Voltage output time series in simulation

Supported by the experimental results, we further determine the feasibility and advantages of making it possible to achieve full synchronization through closed-loop coupled Chua circuits.

Summary

In this paper, we have studied the synchronization process of three Chua circuits when they are closed-loop coupled through capacitance. Three Chua circuits with the same circuit parameters and different initial conditions, which are in a chaotic state and can excite a double vortex attractor, are considered. Starting from the circuit equations of the closed-loop coupling of capacitance, a dimensionless system equation is constructed, which is the key to the subsequent numerical calculations.

After that, we calculate the feasibility of fully synchronizing the three circuits when capacitance is coupled, and the advantages of closed-loop coupling. And, we determined the coupling strength threshold δcriticalC\delta_{\mathrm{critical}}^{C} for capacitive closed-loop coupling by calculating the maximum total error ∑EMax\sum E_{\mathrm{Max}} of the system in a certain time series versus the coupling strength. When the coupling strength δC∈[δcriticalC,δmaxC]\delta^{C} \in[\delta_{\mathrm{critical}}^{C},\delta_{\mathrm{max}}^{C}], the capacitive closed-loop coupling can synchronize the three Chua circuits completely, while δC∈[0,δcriticalC]\delta^{C} \in[0,\delta_{\mathrm{critical}}^{C}] cannot synchronize the circuits. It is also found that the capacitive one-way coupling does not synchronize the circuit completely, regardless of the value of the coupling strength. In particular, if one of the three coupling parameters δC∈[0,δcriticalC]\delta^{C} \in[0,\delta_{\mathrm{critical}}^{C}], the other δC∈[δcriticalC,δmaxC]\delta^{C} \in[\delta_{\mathrm{critical}}^{C},\delta_{\mathrm{max}}^{C}] with the appropriate value can also synchronize the circuit completely. This is the advantage of capacitive closed-loop coupling over other coupling methods.

Finally, we observed the time series at the xx outputs of the three circuits through circuit simulation experiments and compared them with the numerical results again. The feasibility and correctness of the closed-loop coupled Chua circuit using capacitance is further verified. This also provides a new coupling method for the synchronous control of nonlinear circuits.

Acknowledgments

This work is supported by the National Natural Science Foundation of China under Grants No. 12065014 and No. 12047501, and by the Natural Science Foundation of Gansu province under Grant No. 22JR5RA266. We acknowledge the West Light Foundation of The Chinese Academy of Sciences, Grant No. 21JR7RA201.

References

A Circuit Simulation Diagram

Figure 14. Capacitive closed-loop coupling circuit simulation diagram

References

  1. [1]B. C. Bao , C. Liu , J. P. Xu . “Dynamical analysis of memristor chaotic oscillator”, Journal of Physics. 593 , 785 - 3793 (2010).DOI
  2. [2]F. H. Min , C. Li , L. Zhang , et al. “Initial value-related dynamical analysis of the memristor-based system with reduced dimensions and its chaotic synchronization via adaptive sliding mode control method”, Chinese Journal of Physics. 58 (2019).DOI
  3. [3]X. M. Wang , J. Z. He , X. He , et al. “Performance characteristics of an irreversible engine consisting of nonlinear diodes system”, Journal of Physics. 59 , 4460 - 4465 (2010).DOI
  4. [4]Y. Xu. “Periodic bifurcation and chaotic motion in second-order RLC series circuits of single-junction transistors”, Journal of Physics . 100 , 103 (1985).
  5. [5]X. F. Zhang , Z. Y. Chen , Q. S. Bi , et al. “Evolution from regular movement patterns to chaotic attractors in a nonlinear electrical circuit”, Journal of Physics. 59 , 3057 - 3065 (2010).DOI
  6. [6]D. Cafagna , G. Grassi. “Fractional-order Chua’s circuit: time-domain analysis, bifurcation, chaotic behavior and test for chaos”, International Journal of Bifurcation and Chaos . 18 , 615 - 639 (2008).DOI
  7. [7]L. Zhou , F. Tan , F. Yu. “A robust synchronization-based chaotic secure communication scheme with double-layered and multiple hybrid networks” , IEEE Systems Journal . 14 , 2508 - 2519 (2019).DOI
  8. [8]Q. Xie , G. Chen , E. M. Bollt. “Hybrid chaos synchronization and its application in information processing” , Mathematical and Computer Modelling . 35 , 145-163 (2002).
  9. [9]S. Nobukawa , H. Nishimura. “Synchronization of chaos in neural systems” , Frontiers in Applied Mathematics and Statistics . 6 , 19 (2020).DOI
  10. [10]D. Ghosh , S. Banerjee. “Adaptive scheme for synchronization-based multiparameter estimation from a single chaotic time series and its applications”, Phys. Rev. E. 78 , 056211 (2008).pubmed.ncbi.nlm.nih.gov/19113204
  11. [11]D. Ghosh , S. Banerjee. “Projective synchronization of new hyperchaotic system with fully unknown parameters” , Nonlinear Dynamics . 61 , 11 - 21 (2010).DOI
  12. [12]L. M. Pecora , T. L. Carroll . “Synchronization in chaotic system” , Phys. Rev. Lett . 64 , 821 (1990).pubmed.ncbi.nlm.nih.gov/10042089
  13. [13]M. Barahona , L. M. Pecora . “Synchronization in Small-World Systems” , Phys. Rev. Lett . 89 , 054101 (2002).pubmed.ncbi.nlm.nih.gov/12144443
  14. [14]L. M. Pecora , T. L. Carroll . “Master Stability Functions for Synchronized Coupled Systems” , Phys. Rev. Lett . 80 , 2109 (1998).
  15. [15]L. O. Chua “The Genesis of Chua’s Circuit” , Archiv Elektronik Ubertragungstechnik. 46 (1992).
  16. [16]L. O. Chua , P. M. Lin . “Computer-aided analysis of electronic circuits” . Prentice-Hall, (1975)
  17. [17]Y. Xu , R. Shen , W. Li. “Finite-time synchronization for coupled systems with time delay and stochastic disturbance under feedback control” , J. Appl. Anal. Comput. 10 , 1 - 24 (2020).DOI
  18. [18]Q. Ye , Z. Jiang , T. Chen. “Adaptive feedback control for synchronization of chaotic neural systems with parameter mismatches” , Complexity . 2018 , 1 - 8 (2018).DOI
  19. [19]P. Q. Jiang , B. H. Wang , X. S. Luo. “One-way coupled synchronization study of fourth-order Chua’s hyperchaotic circuit” , Systems Engineering and Electronics Technology . 25 , 3 (2003).
  20. [20]S. H. Zhang , L. J. Wan , K. L. Long. “Chua circuit for heterogeneous magnetron memristor design and simulation implementation” . Journal of System Simulation. 31 , 9 (2019).
  21. [21]Z. Liu , J. Ma , G. Zhang , et al. “Synchronization control between two Chua circuits via capacitive coupling” , Applied Mathematics and Computation . 360 , 94 - 106 (2019).DOI
  22. [22]Z. Yao , J. Ma , Y. Yao , et al. “Synchronization realization between two nonlinear circuits via an induction coil coupling” , Nonlinear Dynamics . 96 , 205 - 217 (2019).DOI
  23. [23]X. Zhang , C. Wang, J. Ma, et al. “Control and synchronization in nonlinear circuits by using a thermistor” , Modern Physics Letters B . 34 , 2050267 (2020).DOI
  24. [24]T. Singla , N. Pawar , P. Parmannanda . “Exploring the dynamics of conjugate coupled Chua circuits: Simulations and experiments” , Phys. Rev. E. 83, 026210 (2011).pubmed.ncbi.nlm.nih.gov/21405899
  25. [25]S. Kundu , B. K. Bera , D. Ghosh, et al. “Chimera patterns in three-dimensional locally coupled systems” , Phys. Rev. E. 99 , 022204 (2019).arxiv.org/abs/1902.01036
  26. [26]L. V. Gambuzza , A. Buscarino , L. Fortuna, et al. “Memristor-based adaptive coupling for consensus and synchronization” , IEEE Transactions on Circuits and Systems I: Regular Papers . 62 , 1175 - 1184 (2015).DOI
  27. [27]R. Lu , V. T. Pham , M. Chen , et al. “Network dynamics of coupled Chua circuits: comparison of different coupling elements” , The European Physical Journal Special Topics . 1- 9 (2022).DOI
  28. [28]T. Matsumoto , L. Chua , M. Komuro. “The double scroll” , IEEE Transactions on Circuits and Systems , 32 , 797 - 818 (1985).DOI
  29. [29]J. Ma , A. H. Zhang , Y. F. Xia , et al. “Optimize design of adaptive synchronization controllers and parameter observers in different hyperchaotic systems” , Applied Mathematics and Computation . 215 , 3318 - 3326 (2010).DOI
  30. [30]J. Ma , F. Wu , A. Alsaedi , et al. “Crack synchronization of chaotic circuits under field coupling” , Nonlinear Dynamic . 93 , 2057 - 2069 (2018).DOI

Paper details

vlnc:W_skspwrnf
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents