betaFeedback

WorksPhysics and Astronomy

Probing wetting and solidification dynamics of neon thin films with a high-TcT_c superconducting circuit

Abstract

Integrating condensed noble gases with superconducting circuits offers new opportunities for operating hybrid quantum devices. In particular, electrons on solid neon have recently emerged as exceptionally coherent charge qubits, however the growth of the underlying neon films on patterned devices remains poorly controlled. We monitor neon films near the triple point using a multimode resonator fabricated from high-TcT_c YBCO, which remains superconducting at temperatures where the liquid phase exists and whose geometry sets a thickness-sensing window near 1 μμm. In the liquid state we observe rich film dynamics: uniform wetting that saturates near 20 nm, drainage of thicker films, and spontaneous thickness oscillations, reflecting the extreme sensitivity of thick films in this regime. A galvanic connection to our sensing volume enables in-situ electrostatic tuning of the liquid film thickness. Statistics of freezing the neon across various liquid levels reveal variations of the solid film thickness by approximately an order of magnitude. We also observe a two-fold increase in the quality factor of the resonators at the level of 10310^3 with added neon and rule out dielectric loss as the limiting factor. Our results demonstrate that hermetic packaging facilitates the investigation of both rich non-equilibrium fluid dynamics and the impact of condensed noble gas films on microwave loss in superconducting circuits, but may not be the best modality for growing solid neon films with precisely controlled thickness.

Introduction

Understanding how superconducting circuits couple to external degrees of freedom is at the heart of both developing hybrid quantum architectures and mitigating dielectric loss [1]. Condensed noble gases are an attractive ingredient for such architectures: they are chemically pure, nearly free of nuclear spins, can be grown and tuned in situ at cryogenic temperatures, and support pristine two-dimensional electron gases at their surfaces, motivating proposals for scalable, reconfigurable qubit arrays [2, 3]. In particular, solid neon has recently emerged as a host for both high-coherence electron spin ensembles and single-electron charge qubits with coherence times on the order of ∼100 μs\sim100\ \mu\mathrm{s} [4, 5]. Much of this coherence derives from the rigidity of the solid surface: unlike electrons on liquid helium, whose motional linewidths are limited at the ∼100 MHz\sim100\ \mathrm{MHz} level by coupling to surface capillary waves (ripplons) [6], electrons on neon are immune to this decoherence channel. Despite this progress, the precise nature of the electron wavefunction and the impact of the vacuum/neon/substrate interfaces on qubit coherence are not fully understood [7]. A prerequisite for investigating these questions is understanding the underlying solid neon film itself and how its growth conditions determine its properties.

Solid neon films can be grown in two ways: 1) quench-condensation of gaseous neon directly onto a cold substrate held at a temperature below the triple point or 2) cooling a substrate with a liquid neon film through the triple point. It is known that for liquid neon adiabatically cooled through the triple point Tt=24.56 KT_t = 24.56\ \mathrm{K}, the resulting solid film thickness saturates to just a few monolayers as dictated by triple point wetting physics [8]. Experiments that have reported charge qubits on solid neon have exclusively used the latter method to freeze a liquid film to obtain a solid film thicker than a few monolayers; such a scenario suggests a non-equilibrium freezing modality that warrants further investigation. One challenge in efficiently characterizing the neon film growth is that the triple point of neon is much higher than the temperatures typically suitable for superconducting measurements. Indeed, electron-on-neon charge qubit experiments with conventional superconducting resonators are unable to detect properties of the liquid state when neon is introduced into the hermetic sample cell [5, 9, 10]. This challenge can be circumvented by using high-TcT_c superconducting resonators [11].

In this work, we operate a voltage tunable multimode superconducting resonator fabricated from a high-TcT_c YBCO film to sense the dynamics of liquid and solid neon films in real time. We identify qualitatively different regimes of liquid film dynamics ranging from uniform wetting to spontaneous oscillations, all of which have implications for thickness control. Repeated solidification trials via cooling through the triple point reveal only a weak correlation between initial liquid thickness and final solid thickness and an overall thinning of the film. Finally, we observe a smooth increase in the quality factor of our resonators as a function of neon thickness; such a trend suggests a potential intricate interplay between the neon film and quasiparticle loss.

Experimental Setup

Our measurement is based on the sensitivity of a planar microwave resonator to its dielectric environment. The electric field of a coplanar stripline mode extends above the chip surface over a distance set by the transverse dimensions of the stripline. When neon condenses onto the chip, it replaces vacuum (εr=1\varepsilon_r = 1) with a dielectric (liquid εr≈1.19\varepsilon_r \approx1.19, solid εr≈1.24\varepsilon_r \approx1.24 [13]) within this sensing volume, increasing the capacitance per unit length and lowering the resonance frequency. Continuously tracking the resonance frequency therefore provides an in-situ, real-time record of the neon film thickness on the resonator, with a thickness window set by the field decay length. Because the temperature range of interest lies far above the transition temperatures of conventional superconductors, we fabricate the resonator from the high-TcT_c superconductor YBCO (Tc≈88T_c \approx88 K), which remains deep in its superconducting state at the neon triple point (Tt=24.56T_t = 24.56 K).

In our experiment, we monitor two modes of a YBCO-on-sapphire coplanar stripline resonator (fabricated by STAR Cryoelectronics) enclosed in a hermetic sample cell (Figure 1a). In this work, the cell is mounted to the mixing chamber of a standard Bluefors LD250 dilution refrigerator. The cell is cooled by the pulse tube through the two sets of heat switches between the 4K and mixing chamber stages. The cooling rate of the cell is controlled by adjusting the power applied to a resistive heater mounted at the 4K stage; this enables stabilization of the mixing chamber at a desired temperature around the triple point.

Figure 1. (a) Rendering of the hermetic sample cell used in the experiment [12]. (b) (Left) Schematic of our DC-coupled coplanar stripline resonator. The differential mode frequency is determined by the coplanar strip length LL where the voltage node is located where the pins join. An on-chip LC low pass filter, consisting of a set of interdigitated finger capacitors in series with a spiral inductor to a bond pad, helps suppress leakage of the common mode. (Right) Optical image of the device, with zoom-ins of the voltage anti-node of the coplanar stripline (left) and where the two pins join to define the voltage node for the differential mode (right). Scale bars correspond to 50 μm\mu\mathrm{m} (top) and 10 μm\mu\mathrm{m} (bottom). The DC gate on the left side of the device is unused in this experiment. (c) Cross section of the materials stack. The sample is fabricated from a 300 nm thick film of YBCO deposited on a sapphire substrate with an intermediate buffer layer of 40 nm thick CeO2_2 in between. Electric field lines of the differential (blue) and common (red) modes are shown. The vertical sensing region is determined by the gap width ss.

The resonator, measured in a transmission configuration, is galvanically connected to a DC voltage source that enables control over the local electric field between the center pins and ground (Figure 1b). The length of the section before and after the two center pins are joined determining the frequencies of the common and differential modes (Figure 1b). For the results presented in this paper, we measure the only two modes that are present in our measurement band: the fundamental λ/4\lambda/4-differential and the first overtone 3λ/43\lambda/4-common mode. An independent measurement in a separate cooldown utilizing a 180-degree hybrid confirms the common/differential nature of these modes and shows that they are in the undercoupled regime Qtot≈QintQ_{\mathrm{tot}} \approx Q_{\mathrm{int}} (see Appendix A).

Liquid Film Dynamics

We first characterize condensation in the liquid state by periodically admitting metered doses of neon gas into the sample cell held at T=26T = 26 K, above the triple point. Neon enters the fill line via a gas manifold which operates by pressurizing a 10 cm3^{3} control volume with gaseous neon to a pressure above the triple point pressure (Pt≈433P_{\mathrm{t}} \approx433 mbar) and then opening a switch to the cryostat. A detailed description of the manifold can be found in Ref. [12]. In our experiment, pressures between 1 and 3 bar were used. Each dose dielectrically loads the mode volumes and shifts the resonance frequencies downward as shown in Figure 2a for the differential mode. We observe four qualitatively different regimes. In regime I the frequency decreases gradually and monotonically with each dose, consistent with gradual uniform wetting of the entire surface with a thin liquid film. This film saturates to a thickness of approximately 20 nm (inferred from the model described below), after which regime II begins. Each insertion displays a large initial shift that relaxes toward a steady state, suggesting that each insertion covers the resonator with a thick liquid film that subsequently thins as neon redistributes to the rest of the cell. In regime III, the liquid level becomes unstable, exhibiting fluctuations in level as periodic oscillations occur even without neon insertions. This susceptibility is plausibly related to the enhanced evaporative response of a thin film near saturation, where the rate of exchange between liquid and vapor on the surface of the film sets the dynamics of the film [14, 15]. Such liquid thin films are known to develop periodic thickness oscillations once the heat flux from the substrate exceeds a threshold [16]. Finally in regime IV the frequency shift saturates to a maximum observed value which we identify as the resonator mode volumes being completely filled with neon.

Figure 2. (a) Monitoring the differential mode resonance frequency as liquid neon is filled into the cell held at T=26T = 26 K. Arrows indicate discrete filling events. Data segments for various qualitative regimes (I - IV) are spliced together on same plot with axes breaks to show relative timing. (b) Simulated finite element model of estimating the neon thickness tt from the frequency shift of the resonator modes. (c) In-situ dielectric loading tunability via an applied DC voltage for liquid films of various thicknesses. Each individual trace (example shown in inset) displays no hysteresis.

To translate the observed frequency shift to an effective neon thickness tt, we utilize a model obtained from finite-element simulations (Ansys Maxwell) of the cross sectional mode capacitances as the vacuum above the resonator pins is progressively replaced with neon of various heights (Figure 2b) (see Appendix § 9). This provides a mapping between neon thickness and frequency shift fmeas=f0+δf(t)f_{\mathrm{meas}} = f_{0} + \delta f(t) which we are able to invert to obtain t(fmeas)t(f_{\mathrm{meas}}) under the assumption that the neon film is uniform across the surface of the resonator. The resulting calibration curve highlights a key design consideration: the transverse dimensions of the resonator determine the neon height t∗t^{*} that maximizes the sensitivity df/dt\mathrm{d}f/\mathrm{d}t, which in our work is around t∗≈1 μmt^{*} \approx1\ \mu\mathrm{m}. This geometric tunability suggests that resonators with different cross sections could be multiplexed on a single chip to extend the high-precision window over a larger dynamic range of film thicknesses.

A defining characteristic of a liquid thin film covering the resonator is the ability to in-situ tune the film thickness via a local electric field, as has been shown for superfluid helium [17]. Applying a DC voltage VV to the center pins produces an inhomogeneous field that polarizes the liquid and draws it toward the resonator, thickening the film and shifting the resonance frequency by

δf=αV2\delta f = \alpha V^2

We demonstrate this tunability by sweeping the DC voltage VV of the resonator center pins across inferred liquid film thicknesses, spanning the sensitivity window. The quadratic coefficients of the resulting frequency shifts are plotted in Figure 2c. Individual voltage sweeps show no hysteresis indicating the film responds reversibly and is free of pinning. However, the variance in the data for different trials with similar estimated thicknesses suggests that the liquid is not completely uniform across the resonator’s surface.

Neon solidification

We next investigate solidification by cooling the cell from T=26T = 26K through the triple point. Figure 3a shows a representative trace tracking the frequency of the differential mode as the system is cooled; at the freezing transition the magnitude of the frequency shift abruptly decreases, indicating the film almost always becomes thinner upon solidification. To quantify each trial, we bin the measured frequencies away from the transition (T∈[24.75,26]T \in[24.75, 26]K) for the liquid and (T∈[23,24.2]T \in[23, 24.2]K) for the solid and convert to an average thickness using our finite-element model.

Frequency shift during cooling and liquid-solid film thickness comparison

Figure 3. (a) Left: representative trace of the frequency shift of the differential mode as the mixing chamber is cooled through the freezing point. Right: the frequency data is binned in the temperature ranges T∈[23,24.2]T \in[23, 24.2] K and T∈[24.75,26]T \in[24.75, 26] K for the solid and liquid thickness estimation, respectively. (b) The average film thickness in the liquid and solid states determined from the histogram fits in (a) are plotted against each other across many different trials at two difference cooling rates. Within our statistics, the two cooling rates yield similar distributions. Gray dashed line indicates equal thickness in the liquid and solid states.

The central question of our work is whether control of the liquid film thickness (particularly in regimes I and II) can translate to a controlled solid film thickness. Figure 3b shows the estimated average solid film thickness plotted against the corresponding average liquid film thickness for many repeated trials across the two different cooling rates of approximately ∼\sim1K/hr and ∼\sim5K/hr. The solid films are typically one to two orders of magnitude thinner than the parent liquid, far thinner than a few monolayers but far thinner than the liquid they froze from, consistent with solidification proceeding in a non-equilibrium dewetting process. Thicker liquid films do on average yield thicker solid films, but the correlation is weak: for liquid films in the 1-10 μ\mum range, where the thickness estimate is most precise the resulting solid thickness is reproducible only to within roughly an order of magnitude, while thicker liquid films (t>10 μt > 10\,\mum, for which sensitivity is also reduced) yield reproducible solid thicknesses spanning nearly the full observable range. The general spread of the distribution and lack of a strong influence of the different cooling rate is consistent with previous work [11].

Impact of neon on quality factor

The presence of neon films on top of the resonator modifies the electromagnetic environment of the mode volumes; it is thus natural to investigate the impact of the neon film thickness on the quality factor of the modes. Strikingly, we find that the quality factor smoothly increases (by up to 2×2\times) with neon film thickness for both liquid and solid films (Figure 4). It is natural to ask whether or not this increase can be explained by a dielectric loss model:

Figure 4. Loaded quality factor QLQ_L of the common (red) and differential (blue) modes as a function of neon level in both solid (circles, T=23.5KT = 23.5\mathrm{K}) and liquid (squares, T=25KT = 25\mathrm{K}) states. A dielectric loss model attributing all the loss to the decreasing participation ratio of the CeO2_2 buffer layer is insufficient to explain the data (black line). The shaded region represents a factor of two range of the dielectric constant of CeO2_2.

1Q(t)=1Qother+∑ipi(t)qi(1)\frac{1}{Q(t)} = \frac{1}{Q_{\mathrm{other}}} + \sum_i \frac{p_i(t)}{q_i} \tag*{(1)}

where pi(t)p_i(t) are the thickness dependent participation ratios of the neon film, CeO2_2 buffer layer, a surface region for both the YBCO-vacuum and sapphire-vacuum interfaces, and the bulk sapphire, and qiq_i are the quality factors of each region. As the neon film thickness increases, pneon(t)p_{\mathrm{neon}}(t) increases while all other participation ratios adjust accordingly. Thus, an increase in the overall quality factor would suggest that QQ is limited by a lossy dielectric region whose participation decreases with the neon thickness; in this case, this would correspond to the CeO2_2 buffer layer. However, finite element simulations of the participation ratios rule out this scenario (see App. § 10). This conclusion is consistent with the fact that YBCO resonators are typically limited by conductor loss, especially at elevated temperatures [18, 19]. We leave a detailed investigation of the interplay between the neon film and quasiparticle loss mechanisms as a subject for future work. Our results motivate a deeper and continued investigation of how condensed noble gas films influence the quality factor of superconducting resonators. Recent work on this front has demonstrated that incorporating condensed cryogenic films on superconducting circuits can reduce the absorption of stray terahertz radiation [20] or potentially remove surface impurities [21].

Conclusion and Outlook

In this work, we utilized a voltage-tunable multimode coplanar stripline resonator in a hermetic cell to systematically explore dynamics across the entire range of liquid neon thicknesses in the resonator’s modal sensing volume. The data reveal rich non-equilibrium dynamics of the liquid film that likely contribute to reduced uniformity across the sample surface. This may be due to the many thermal links between the cooling source and the substrate; more direct control of the local temperature may help facilitate better control of the film properties [11]. Repeated solidification trials reveal that the solid film thickness is set only coarsely by the liquid film from which it froze, with an order of magnitude spread that is insensitive to the cooling rate over the range explored. We also find that the neon film increases the quality factor of both resonator modes, an improvement that cannot be attributed to dielectric loading and that adds to growing evidence that condensed-gas overcoats can benefit superconducting circuits in certain circumstances.

Thus far, electron-on-neon qubits have only been demonstrated on solid thin films grown via freezing a liquid film in a hermetic cell. Our results motivate the investigation of such qubits on quench-condensed films which have better thickness control [4]. Such an approach is compatible with cryogenic atomic force microscopy, which would be a powerful complementary technique for obtaining spatial information on quantities of interest like surface roughness which cannot directly be resolved with resonator measurements. This would allow a systematic study of the influence of both neon thickness and roughness on qubit properties, which are likely to be heavily influenced by surface disorder [7]. Ultimately, the ability to grow solid neon films with controllable thickness and low roughness would potentially enable the operation of a high mobility two-dimensional electron gas for reconfigurable electron spin qubits without suffering the loss channel of ripplons as is the case for liquid helium.

Acknowledgments

This work was primarily supported by the Air Force Office of Scientific Research (AFOSR) under Award no. FA9550-23-1-0636. C.S.L. acknowledges support of both the Grainger Fellowship from the University of Chicago and the Department of Energy’s Q-NEXT National Quantum Information Science Research Center.

Device characterization

Here we describe the reference characterization of our sample. A resistivity measurement of the YBCO film reveals a critical temperature Tc≈88 KT_c \approx88\ \mathrm{K} and a linear dependence of the resistivity ρ=ρ0+α(T−Tc)\rho= \rho_0 + \alpha(T-T_c) for T>TcT > T_c with ρ0≈50 μΩ⋅cm\rho_0 \approx50\ \mu\Omega\cdot\mathrm{cm} and α≈0.625 μΩ⋅cm/K\alpha\approx0.625\ \mu\Omega\cdot\mathrm{cm/K}. In the experiment, we only observe the two modes presented in the main text in our measurement band (4 - 8 GHz). This is supported by HFSS simulations of the entire device which predicts mode frequencies of approximately 5.9 GHz and 6.1 GHz for the λ/4\lambda/4 differential and 3λ/43\lambda/4 common modes, respectively. The simulation does not capture the effects of kinetic inductance and the CeO2_2 buffer layer, which likely contribute to the discrepancy between the simulated and measured values. The simulation also reveals that a significant fraction of the common mode volume lives in the on-chip low pass filter, whereas this is not true for the differential mode as expected. The temperature dependence of the mode frequencies and quality factor are shown in Figure 5.

Figure 5. Temperature dependence of the resonant frequency fresf_{\mathrm{res}} and loaded quality factor QLQ_L of the differential (top) and common (bottom) modes.

Dielectric filling model

In order to obtain the model used in Figure 2b of the main text, we perform 2D cross-section simulations of the static capacitances between the center pin electrodes and ground with varying amounts of neon using Ansys Maxwell. By utilizing known formulas for the effective capacitance of the common and differential modes of a coplanar stripline (see Ref. [12]), we are able to translate between frequency shift and neon thickness. We note that the galvanic connection of the common mode to the lumped on-chip filter is not accounted for in our modeling and results in some error.

The frequency shifts are scaled to the maximum observed frequency shift for the corresponding phase of neon. Dielectric constants of ϵrl=1.194\epsilon_r^l = 1.194 and ϵrs=1.244\epsilon_r^s = 1.244 are used for the liquid and solid phases, respectively [13]. Numerical values of both the simulated and measured maximum frequency shifts are given in Table I.

SimulatedMeasured
Differential, liquid66.9667.99
Differential, solid83.7880.28
Common, liquid73.5370.92
Common, solid92.0082.13

Table I. Simulated and measured values of the frequency difference Δfmax⁡\Delta f_{\max} in MHz between an empty sample cell (i.e. vacuum above the sample surface) and being fully covered in neon.

Figure 6. (a) Cross section of 2D finite element Ansys Maxwell simulation. The dielectric regions are chosen as the bulk sapphire (ϵsapphire=10\epsilon_{\mathrm{sapphire}} = 10), the 40 nm thick layer of CeO2_2 (ϵCeO2=26\epsilon_{\mathrm{CeO_2}} = 26), a 10 nm thick surface layer (informed by AFM images that reveal significant surface roughness) that encompasses both the metal-air and substrate-air interfaces (ϵsurf=10\epsilon_{\mathrm{surf}} = 10), and the neon film. (b) Percent change in the participation ratio δp=(pi(t)−pi(t0))/pi(t0)\delta p = (p_i(t)-p_i(t_0))/p_i(t_0) of each dielectric volume relative to a reference simulation with a uniform coverage of t0=20t_0 = 20 nm as a function of neon thickness tt.

Participation ratio simulations

The participation ratio calculations for the loss estimate in Figure 4 follow a simplified version of the methodology presented in Ref. [22]. Typically, 3D simulations are used to extract the fields over a wide range of length scales for aperiodic and lumped-element geometries while 2D simulations are used to rescale divergent electric fields at structure edges and faces. This allows for the capture of long-distance field variation due to device-scale boundary conditions while still accounting for electric field variation on dielectric boundaries at the nanometer scale. There is a complex interface bandaging and rescaling method that links the two and three dimensional cases consistently and prevents double-counting. The differential mode of our coplanar stripline (CPS) structure can be accurately modeled with 2D simulations alone. Since the differential mode leakage is limited beyond the node of the CPS, the CPS structure is entirely uniform in its cross section. The ground plane is also nearby, so electric fields decay in magnitude radially with a constant on the order of the feature size, so the modal volume is very well represented even when only sampling within one or two orders of magnitude of the feature size. This is in contrast to structures such as transmon capacitor pads, whose sizes are comparable to the substrate thickness, and n-polar coplanar waveguides with distant grounds such as those measured in cavities. As a result, there is no bandaging or rescaling required since the 2D simulation samples the field well and more finely than a 3D simulation regardless. If our resonators were of a higher quality factor, it would be necessary to follow other examples in dividing our surfaces and interfaces into more specific sections, but at this level it is appropriate to bound significant loss within regions with very small participation. Finally, we note that our analysis provides a framework and quantitative estimates for determining how integrating condensed cryogenic films can provide insight towards dielectric loss mechanisms in state-of-the-art superconducting devices.

References

  1. [1]A. A. Clerk, K. W. Lehnert, P. Bertet, J. R. Petta, and Y. Nakamura, Hybrid quantum systems with circuit quantum electrodynamics, Nature Physics 16, 257 (2020), number: 3.DOI
  2. [2]S. A. Lyon, Spin-based quantum computing using electrons on liquid helium, Physical Review A 74, 052338 (2006).DOI
  3. [3]E. Kawakami, J. Chen, M. Benito, and D. Konstantinov, Blueprint for quantum computing using electrons on helium, Physical Review Applied 20, 054022 (2023).DOI
  4. [4]A. N. Kanagin, N. d. Zordo, A. Angerer, W. Kersten, N. Lagos, J. Schmiedmayer, and E. S. Redchenko, Impurities in cryogenic solids: a new platform for hybrid quantum systems (2025), arXiv:2508.21651 [quant-ph].arxiv.org/abs/2508.21651
  5. [5]X. Zhou, X. Li, Q. Chen, G. Koolstra, G. Yang, B. Dizdar, Y. Huang, C. S. Wang, X. Han, X. Zhang, D. I. Schuster, and D. Jin, Electron charge qubit with 0.1 millisecond coherence time, Nature Physics 20, 116 (2024).DOI
  6. [6]G. Koolstra, E. O. Glen, N. R. Beysengulov, H. Byeon, K. E. Castoria, M. Sammon, S. A. Lyon, D. G. Rees, and J. Pollanen, Strong coupling of a microwave photon to an electron on helium, Nature Physics , 1 (2026).DOI
  7. [7]K. Zheng, X. Song, and K. W. Murch, Surface-Morphology-Assisted Trapping of Strongly Coupled Electron-on-Neon Charge States, Physical Review Letters 135, 080601 (2025).arxiv.org/abs/2503.01847
  8. [8]A. D. Migone, J. G. Dash, M. Schick, and O. E. Vilches, Triple-point wetting of neon films, Physical Review B 34, 6322 (1986).pubmed.ncbi.nlm.nih.gov/9940510
  9. [9]X. Zhou, G. Koolstra, X. Zhang, G. Yang, X. Han, B. Dizdar, X. Li, R. Divan, W. Guo, K. W. Murch, D. I. Schuster, and D. Jin, Single electrons on solid neon as a solid-state qubit platform, Nature 605, 46 (2022).DOI
  10. [10]X. Li, C. S. Wang, B. Dizdar, Y. Huang, Y. Wen, W. Guo, X. Zhang, X. Han, X. Zhou, and D. Jin, Solid neon as a noise-resilient host for electron qubits above 100 mK, Nature Electronics , 1 (2026).arxiv.org/abs/2502.01005
  11. [11]S. Duthaluru, K. Zheng, E. A. Henriksen, and K. W. Murch, Real-time monitoring of growth of neon film for electron-on-neon qubits, Physical Review Applied 25, 044065 (2026).DOI
  12. [12]G. Koolstra, Trapping a Single Electron on Superfluid Helium using a Superconducting Resonator, Ph.D. thesis, University of Chicago (2019).DOI
  13. [13]M. W. Cole and M. H. Cohen, Image-Potential-Induced Surface Bands in Insulators, Physical Review Letters 23, 1238 (1969).DOI
  14. [14]A. Oron, S. H. Davis, and S. G. Bankoff, Long-scale evolution of thin liquid films, Reviews of Modern Physics 69, 931 (1997).DOI
  15. [15]R. V. Craster and O. K. Matar, Dynamics and stability of thin liquid films, Reviews of Modern Physics 81, 1131 (2009).DOI
  16. [16]T. T. T. Nguyen, J. Yu, J. L. Plawsky, P. C. Wayner, D. F. Chao, and R. J. Sicker, Spontaneously oscillating menisci: Maximizing evaporative heat transfer by inducing condensation, International Journal of Thermal Sciences 128, 137 (2018).DOI
  17. [17]G. Yang, A. Fragner, G. Koolstra, L. Ocola, D. Czaplewski, R. Schoelkopf, and D. Schuster, Coupling an Ensemble of Electrons on Superfluid Helium to a Superconducting Circuit, Physical Review X 6, 011031 (2016).DOI
  18. [18]F. Gao, J. W. Kruse, C. E. Platt, M. Feng, and M. V. Klein, Microwave surface impedance at 10 GHz and quasiparticle scattering in YBa2Cu3O7 films, Applied Physics Letters 63, 2274 (1993).
  19. [19]Z. Velluiure-Pellat, E. Maréchal, N. Moulonguet, G. Saïz, G. C. Ménard, S. Kozlov, F. Couëdo, P. Amari, C. Medous, J. Paris, R. H. Costein, J. Lebueur, C. Feuillet-Palma, and N. Bergeal, Hybrid quantum systems with high-T $$c$$ superconducting resonators, Scientific Reports 13, 14366 (2023).
  20. [20]F. Valenti, A. N. Kanagin, A. Angerer, L. Buimaga-Iarinca, C. Morari, J. Schmiedmayer, and I. M. Pop, Hydrogen crystals reduce dissipation in superconducting resonators, Physical Review B 109, 054503 (2024).DOI
  21. [21]K. Matkovic, P. Russell, A. Palmer, E. Helgemo, L. Delventhal, K. Zuo, K. Surse, R. Rahman, and M. C. Cassidy, Characterizing Neon Thin Film Growth with an NbTiN Superconducting Resonator Array (2025), arXiv:2510.21029 [cond-mat.mes-hall].arxiv.org/abs/2510.21029
  22. [22]C. Wang, C. Axline, Y. Y. Gao, T. Brecht, Y. Chu, L. Frunzio, M. H. Devoret, and R. J. Schoelkopf, Surface participation and dielectric loss in superconducting qubits, Applied Physics Letters 107, 162601 (2015).DOI

Paper details

vlnc:W_t97c7xex
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 3

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents