betaFeedback

WorksPhysics and Astronomy

A Computational Procedure for Assessing Ic_c(ε\varepsilon) in Nb3_3Sn/Bi-2212 Hybrid Magnets

Abstract

The critical current of superconductors is commonly measured by testing unloaded wires under an external magnetic field. While stressed by intense Lorentz forces, the existing HTS/LTS superconductors are prone to a reduction in critical current before reaching their structural mechanical limit. In this work, the magnetic and mechanical analysis of the FNAL 4-layer Bi-2212/Nb3_3Sn hybrid dipole magnet is reported, aimed at predicting the critical current degradation for both the superconductors during powering at 16 T. All the Rutherford cables in the coils of the hybrid magnet were modeled at the strand level in Ansys APDL with the heterogeneous cable model. Utilizing this detailed geometry, it was possible to evaluate the effects of strain on the critical current degradation for both the Nb3_3Sn and Bi-2212 superconductors under the intense Lorentz forces. The analysis presented in this paper integrates strain-dependent critical current laws, with parameters derived from experimental data, to simulate the hybrid magnet's performance for all possible current-powering configurations. The proposed methodology enables a detailed assessment of conductor integrity and IC_C(ε\varepsilon) reduction in existing hybrid magnet designs, providing a versatile and rigorous framework for optimizing future high-field hybrid magnets.

Introduction

The main goal of Area II of the U.S. Magnet Development Program (MDP) is to demonstrate the performance of HTS magnets with the intent of developing and testing hybrid magnets beyond the limit of 16 T, advancing the technology of high and low temperature superconductor (HTS/LTS) [1]. At high field, the stress and strain state inside the superconductor strands can reach critical levels due to intense Lorentz forces,

particularly in the innermost layers of the hybrid magnet. Such mechanical loads can degrade the performance of both HTS and LTS superconductors. To control the distribution of stress and strain within the conductors, innovative tools and technology have been developed: from the design perspective, the structural geometry called stress-managed cosine-theta (SMCT) has been introduced to control the stress intensity in the conductor [2, 3, 4, 5, 6]. From a computational perspective, detailed cable models at the strand level, known as heterogeneous models, have been previously developed to assess conductor integrity and evaluate the reduction in critical current caused by strain [7, 8, 9, 10, 11]. In this paper, we present the magnetic and mechanical analysis of the FNAL HTS/LTS dipole by applying a computational procedure that implements the heterogeneous Rutherford cable model for the first time to the entire hybrid magnet, cross-section in Figure 1. The critical current degradation law due to strain for Nb3_3Sn was implemented as described in [12]. For the Bi-2212 superconductor, the degradation law due to strain was obtained from the transverse pressure ICI_{\mathrm{C}} degradation measurements performed by the University of Twente [13]. The strain-state and magnetic field results from the FEM analysis in each superconductor region were then used as input to compute the IC(B,T,ε)I_{\mathrm{C}}(B, T, \varepsilon) reduction across all the possible current powering configurations of the hybrid dipole. This approach allowed the detailed analysis of an existing hybrid magnet design. The parametric nature of this procedure enables its application to different or new dipole geometries, providing a valuable tool for scientists and

Image not extracted

Figure 1. Schematic representation of the 4-layer hybrid magnet in dipole configuration, with the inset coil made of Bi-2212 Rutherford cable (Bi-SMCT1) and the outer cosine-theta coil in Nb3_3Sn.

A. D’Agliano is with the Lawrence Berkeley National Laboratory, Berkeley, CA, 94720, USA, and also with the University of Pisa, Pisa, 56126, Italy (Corresponding author, e-mail: [email protected]).

I. Novitski and A. V. Zlobin are with the Fermi National Accelerator Laboratory, Batavia, IL, 60510, USA.

G. Vallone and P. Ferracin are with the Lawrence Berkeley National Laboratory, Berkeley, CA, 94720, USA.

E. Barzi, is with Ohio State University, Columbus, OH, 43210, USA.

S. Donati and V. Giusti are with the University of Pisa, Pisa, 56126, Italy. engineers involved in the design and optimization of future high-field hybrid magnets.

Parametervaluesunit
Bi-2212 LBNL-1110 Cable, PMM180207-2
Strand
Number of strands17
Bare cable width7.8mm
Bare cable thickness1.44mm
Strand diameter before/after reaction0.80/0.778mm
Strand JCJ_C (4.2 K, 5 T)460 - 640A/mm2^2
Nb3_3Sn cable, RRP-108/127 Strand
Number of strands40
Bare cable width14.847mm
Bare cable mid-thickness1.307mm
Strand Diameter0.7±0.0030.7 \pm0.003mm
Strand JCJ_C (4.2K, 12T)2643A/mm2^2

Table 1. Rutherford cables and strands parameters.

Cross-section of the heterogeneous Rutherford cable model for the Bi-2212 and Nb3Sn superconductors

Figure 2. Cross-section of the heterogeneous Rutherford cable model for the Bi-2212 (top) and Nb3_3Sn (bottom) superconductors (cables are not in scale).

Methodology

Heterogeneous Rutherford cable model

Rutherford cable models, detailed at the strand level, were implemented in ANSYS APDL to obtain a precise stress and strain state distribution in the magnet coils and to compute the accurate critical current reduction due to strain during powering. Table I reports the strand and Rutherford cable parameters for the Bi-2212 and Nb3_3Sn superconductors. Figure 2 shows the materials and the geometrical dimensions used as input in ANSYS APDL to implement the heterogeneous Rutherford cable model for the first time on a hybrid magnet design. Material properties for the Nb3_3Sn cable could be found in [14], while those for the Bi-2212 cable are reported in Table II.

Critical Current Scaling Law - Nb3_3Sn

The method used to define the Nb3_3Sn critical current as a function of the applied magnetic field and the strain-state

MaterialYoung Modulus [GPa]Poisson RatioYield Strength [MPa]
Silver83/910.36437/52
Bi-221245/500.3537/52
Mullite13/200.31500/600
Epoxy5/60.3987/96

Table 2. Material properties at 300/4.2 K.

Figure 3. Normalized ICI_C degradation Ω(ε)\Omega(\varepsilon) (at 4.2 K, 11 T) as a function of the area-averaged strain state in the Bi-2212 Rutherford cable strands due to transverse pressure.

within the superconductor strands at 4.2 K was obtained from [12]. To evaluate the IC(B,T,ε)I_C(B,T,\varepsilon), the critical surface of the 40-strand Nb3_3Sn Rutherford cable was parametrized. Then the ’strain’ function s(ε)s(\varepsilon) was added to the ICI_C equation using the exponential scaling law and assuming: C1=0.89C_1 = 0.89 and εl0=−0.2\varepsilon_{l0} = -0.2. The strain function was computed as:

s(ε)=Bc2(0,ε)Bc2(0,0)=e−C1I22+3I22+1J2+e−C1I12+3I12+1J122(1)s(\varepsilon)=\frac{B_{c2}(0,\varepsilon)}{B_{c2}(0,0)}=\frac{e^{-C_1\frac{I_2^2+3}{I_2^2+1}J_2}+e^{-C_1\frac{I_1^2+3}{I_1^2+1}J_1^2}}{2} \tag*{(1)}

where I1I_1 and J2J_2 are respectively the first and second invariants of the area-averaged strain tensor ε\varepsilon computed in each Rutherford cable’s strand. The strain function can be defined as the ratio of the strain-dependent upper critical field Bc2B_{c2} at zero temperature, and Bc2B_{c2} at zero temperature and strain. The IC(B,T,ε)I_C(B,T,\varepsilon) depends but is not proportional to the strain function s(ε)s(\varepsilon).

Critical Current Degradation Law - Bi-2212

The critical current degradation of the Bi-2212 conductor due to transverse pressure was obtained from recent measurements at Twente University [13]. A mechanical FEM simulation reproducing Twente’s experimental setup of a single Bi-2212 Rutherford cable was performed to correlate the azimuthal pressure with the strain state inside the cable’s strands. Combining those two relations, the critical current degradation law due to strain in the HTS Rutherford cable was obtained, as shown in Figure 3. The initial steep trend of the relative ICI_C is associated with the cable’s elastic regime. When the Bi-2212 composite cable reaches the plastic regime, the degradation gradient drastically reduces.

The relative critical current can be interpreted as a scaling coefficient that reduces the nominal ICI_C due to the strain state intensity. For that reason, in this work, it was defined as the ratio of the degraded critical current and the critical current at zero strain: Ω(ε)=IC(B,T,ε)/IC(B,T,0)\Omega(\varepsilon)=I_C(B,T,\varepsilon)/I_C(B,T,0). In this formulation, Ω(ε)\Omega(\varepsilon) is independent of the magnetic field in the conductor.

Magnet Design

Magnetic assumptions

A high-field Nb3_3Sn accelerator magnet beyond the 16 T limit requires the use of HTS superconductor coils in the innermost layers, where the maximum field is achieved [15, 16, 17]. For this reason, the first HTS stress-managed cosine-theta (SMCT) coil made of Bi-2212 Rutherford cable in dipole configuration, called Bi-SMCT1, was conceptualized at Fermilab and is currently under assembly at LBNL [18, 19, 20, 21, 22]. This HTS insert coil is designed to fit the 60 mm aperture of the 2-layer standard cosine-theta Nb3_3Sn demonstrator developed at Fermilab in the past years [23]. An 80 mm thick iron yoke surrounds the proposed design hybrid magnet in a dipole configuration. Its main parameters are reported in Table III. The critical current parametrization at 4.2 K of the two superconductors is reported in Figure 4. The plot reports also the load lines of HTS insert and LTS outsert standalone powering, as well as the series connection powering. For each of those three powering configurations, the magnetic field in the bore (BOB_O) and the maximum magnetic field in the conductor (BCB_C) are plotted as a function of the energizing current. The series powering load-line intersects the Bi-2212

Parametervalues
Bi-2212 Insert ID - OD, mm16 - 58
Nb3_3Sn Outsert ID - OD, mm60 - 122
Number of Bi-2212 turns, L1 - L23 - 6
Number of Nb3_3Sn turns, L1 - L222 - 34
Iron yoke OD, mm400
Max. transverse size w/ shell, mm545

Table III. 4-LAYER HYBRID DIPOLE CONFIGURATION

Figure 4. IC(B)I_C(B) curves of the Bi-2212 (blue) and Nb3_3Sn (red) superconductors at 4.2 K with the load-lines of: powering HTS insert only (grey), powering LTS outsert only (orange), hybrid dipole in series powering configuration (green), and optimal load-lines for both HTS and LTS conductors (thin black lines).

JCJ_C function at a current value of 9.63 kA and a bore field of 12.9 T. Multiple magnetic simulations, with iron yoke, were performed in ANSYS APDL, varying IHTSI_{HTS} and ILTSI_{LTS} currents to obtain the magnetic field in the bore in different powering configurations. Those points were then interpolated to obtain the magnetic results in all the possible configurations. The optimal currents for powering this specific hybrid magnet design were found to be IHTSI_{HTS} = 9 kA and ILTSI_{LTS} = 13.5 kA with approximately 16 T of bore field (see section IV-B, Figure 7). The maximum values of the magnetic field in the bore and each conductor layer for both the series and optimal powering configurations are reported in Table IV.

Powering
SeriesOptimal
IHTSI_{HTS} [kA]9.69
ILTSI_{LTS} [kA]9.613.5
Bore field [T]12.915.9
B conductor, L1 [T]13.416.3
B conductor, L2 [T]12.415.4
B conductor, L3 [T]11.414.7
B conductor, L4 [T]9.512.3

Table IV. HYBRID DIPOLE MAGNETIC RESULTS AT 4.2 K

Figure 7. Magnetic field in the bore of the hybrid dipole varying ILTSI_{LTS} and IHTSI_{HTS}. The red and blue lines are the IC(B)I_C(B) at zero strain for Nb3_3Sn and Bi-2212, respectively. The black star represents the optimal powering, the white star the IC(ε)I_C(\varepsilon) in that configuration. The white dotted line highlights the critical current degradation for all the configurations at 4.2 K.

Mechanical Analysis

Mechanical Structure

The mechanical simulation of the hybrid dipole modeled with the heterogeneous Rutherford cable model is computationally demanding. To simplify the analysis, the results of the entire mechanical structure, loaded at pre-stress, cool-down, and powering, were replaced with those of a simplified model shown in Figure 5. The latter consists of removing the iron yoke, aluminum clamp, and stainless-steel shell from the simulation, inserting infinitely rigid boundary conditions at the dipole OD (yellow dotted line in Figure 5), and loading the conductors with Lorentz forces only, considering exclusively the powering load step.

Mechanical structure and materials of the hybrid dipole magnet

Figure 5. Mechanical structure and materials of the hybrid dipole magnet implemented in ANSYS to compute the mechanical analysis.

Mechanical Results

Figure 6 shows the equivalent Von Mises stress in the Rutherford cable areas computed in the mechanical analysis with the homogeneous cable model. The peak stress at powering in the Bi-2212 cable is 72 MPa, while in the Nb3_3Sn is 215 MPa and localized at the corner of the second layer pole turn. The rest of the Nb3_3Sn conductor is within the stress limit of 180 MPa.

Equivalent Von-Mises stress distribution

Figure 6. Plot of the equivalent Von-Mises stress distribution in the HTS (left) and LTS (right) coil at optimal powering only (IHTSI_{HTS} = 9 kA, ILTSI_{LTS} = 13.5 kA), homogeneous cable model at 4.2 K.

The mechanical analysis of the hybrid magnet with heterogeneous Rutherford cable model enables the detailed computation of the superconducting areas’ strain state distribution. The obtained ε\varepsilon and BB arrays were used as input for the calculation of the critical current degradation IC(B,T,ε)I_C(B, T, \varepsilon) in each strand element of the two superconductors as defined in section II-B. The final step of the analysis involved computing the critical current degradation of both superconductors for the entire set of powering configurations of the hybrid magnet at short sample limit. To do so, the magnetic field in the bore was plotted for all the combinations of IHTSI_{HTS} and ILTSI_{LTS} currents, highlighting the critical current limit for both the Bi-2212 and the Nb3_3Sn at zero strain. Eight points on the critical surface were chosen, and for each of them, the mechanical simulations were computed on the LBNL Lawrencium cluster. For each run performed, results were collected as for the optimal powering configuration shown above. Results of this work are reported in Figure 7. At each black dot representing a specific powering configuration at zero strain, a white dot is associated, identifying the magnetic field with degraded critical current. The white dotted line shown in the plot is obtained by interpolating the computed results, and represents the conductors’ IC(B,T,ε)I_C(B, T, \varepsilon) degradation for the powering configuration on their critical surface.

The peak of ICI_C degradation in Bi-2212 and Nb3_3Sn happens at optimal powering configuration, respectively with values of 0.5% and 10% (13% due to stress intensification in the turn at pole region), and nominal IC(B,T,ε)I_C(B, T, \varepsilon) values of 9 kA and 14.9 kA. Figure 8 reports the results obtained for the optimal powering configuration of the hybrid magnet, specifically the magnetic field in the conductors, the Ω(ε)\Omega(\varepsilon) for the Bi-2212, the strain function for the Nb3_3Sn, and the degraded IC(B,T,ε)I_C(B, T, \varepsilon) in each strand of the conductors. In the degraded configuration, the hybrid dipole can generate a bore field of 14.4 T, which is 9.8% lower than the bore field at zero strain. The relatively small ICI_C reduction in the Bi-2212 Rutherford cable compared to the one in the LTS is due to the effect of the SMCT design for the HTS insert, where stresses are progressively distributed on the mandrel structure.

Magnetic and mechanical analysis results for the optimal configuration

Figure 8. Magnetic and mechanical analysis results for the optimal configuration: magnetic field in the conductor strands (top), Ω(ε)\Omega(\varepsilon) and ’strain’ function s(ε)s(\varepsilon) (center), and IC(B,ε)I_C(B, \varepsilon) current (bottom) in Bi-2212 strands (left) and Nb3_3Sn strands (right).

Conclusion

In this paper, the magnetic analysis of the hybrid HTS/LTS dipole developed at FNAL is presented for every combination of powering currents. The magnetic results of the series and optimal configurations at the short sample limit were reported and compared. For these two configurations, a mechanical analysis using the heterogeneous Rutherford cable model was performed to evaluate the critical current reduction due to strain during powering. The distribution of the magnetic field in the conductor, the critical current degradation, and the nominal degraded current in each strand were reported for the optimal configuration.

The computation of the IC(B,T,ε)I_C(B, T, \varepsilon) for both Bi-2212 and Nb3_3Sn was performed for all the powering configurations at short sample limit to investigate the behavior of the HTS/LTS superconductor within the hybrid dipole structure. Results show that with the chosen parametrization, the Bi-2212 critical current reduction due to strain is lower than the Nb3_3Sn ICI_C reduction. This underlines the conductor benefits of the SMCT structure implemented for the Bi-2212 insert compared to the standard cosine-theta design. The reported procedure utilizing the heterogeneous Rutherford cable model can be extended to alternative hybrid magnet designs and conductor shapes.

Acknowledgments

The author wants to thank Lucas Brower for the valuable technical advice given to enhance the quality of this work.

References

References

  1. [1]The U.S. Magnet Development Program. ”https://usmdp.lbl.gov/strategic-documents”.
  2. [2]A. V. Zlobin, J.R. Carmichael, V.V. Kashikhin, I. Novitski, ”Conceptual Design of a 17 T Nb3Sn Accelerator Dipole Magnet”, 9th International Particle Accelerator Conference, IPAC’18, doi:10.18429/JACoW-IPAC2018-WEPML027.DOI
  3. [3]I. Novitski, A. V. Zlobin, J. Coghill, E. Barzi and D. Turrioni, ”Development of a 120-mm Aperture Nb3Sn Dipole Coil With Stress Management,” in IEEE Transactions on Applied Superconductivity, vol. 32, no. 6, pp. 1-5, Sept. 2022, Art no. 40060052, doi: 10.1109/TASC.2022.3163062. https://ieeexplore.ieee.org/document/9756214DOI
  4. [4]I. Novitski, A. V. Zlobin, E. Barzi and D. Turrioni, ”Design and Assembly of a Large-Aperture Nb3Sn Cos-Theta Dipole Coil With Stress Management in Dipole Mirror Configuration,” in IEEE Transactions on Applied Superconductivity, vol. 33, no. 5, pp. 1-5, Aug. 2023, Art no. 4001405, doi: 10.1109/TASC.2023.3244894. https://ieeexplore.ieee.org/document/10057115DOI
  5. [5]A. V. Zlobin et al., ”Development and test of a large-aperture Nb3Sn cos-theta dipole coil with stress management”, IPAC-24. https://doi.org/10.18429/JACoW-IPAC24-WEPS68
  6. [6]A. V. Zlobin, I. Novitski, M. Baldini and E. Barzi, ”Quench Performance of a Large-Aperture Nb3Sn Cos-Theta Coil With Stress Management in Dipole Mirror Configurations,” in IEEE Transactions on Applied Superconductivity, vol. 35, no. 6, pp. 1-5, Sept. 2025, Art no. 0600505, doi: 10.1109/TASC.2024.3508572. https://ieeexplore.ieee.org/document/10816553DOI
  7. [7]G. Vallone, E. Anderssen, B. Bordini, P. Ferracin, J. F. Troitino and S. Prestemon, ”A methodology to compute the critical current limit in Nb3Sn magnets”, 2021 Supercond. Sci. Technol. 34 025002 https://iopscience.iop.org/article/10.1088/1361-6668/abc56bDOI
  8. [8]A. D’Agliano et al., ”FEM Analysis of Hybrid LTS/HTS Cos-Theta Dipole Magnet With Heterogeneous Cable Model,” in IEEE Transactions on Applied Superconductivity, vol. 35, no. 5, pp. 1-5, Aug. 2025, Art no. 4000105, doi: 10.1109/TASC.2024.3502578. https://ieeexplore.ieee.org/document/10753885DOI
  9. [9]G. Vallone, B. Bordini and P. Ferracin, ”Computation of the Reversible Critical Current Degradation in Nb3Sn Rutherford Cables for Particle Accelerator Magnets,” in IEEE Transactions on Applied Superconductivity, vol. 28, no. 4, pp. 1-6, June 2018, Art no. 4801506, doi: 10.1109/TASC.2018.2810222. https://ieeexplore.ieee.org/document/8303782DOI
  10. [10]E. Barzi, C. Franceschelli, I. Novitski, E. Sartori and A. V. Zlobin, ”Measurements and Modeling of Mechanical Properties of Nb3Sn Strands, Cables, and Coils,” in IEEE Transactions on Applied Superconductivity, vol. 29, no. 5, pp. 1-8, Aug. 2019, Art no. 8401808, doi: 10.1109/TASC.2019.2906734. https://ieeexplore.ieee.org/document/861728DOI
  11. [11]Patrick Ebermann et al., ”Irreversible degradation of Nb3Sn Rutherford cables due to transverse compressive stress at room temperature”, 2018 Supercond. Sci. Technol. 31 065009. https://iopscience.iop.org/article/10.1088/1361-6668/aab5faDOI
  12. [12]B. Bordini, P. Alknes, L. Bottura, L. Rossi and D. Valentinis, ”An exponential scaling law for the strain dependence of the Nb3Sn critical current density”, 2013, Supercond. Sci. Technol., 26, 075014, DOI 10.1088/0953-2048/26/7/075014. https://iopscience.iop.org/article/10.1088/0953-2048/26/7/075014DOI
  13. [13]A. Kario et al., ”Critical Current Reduction by Transverse Pressure in Bi-2212 Rutherford cables up to 300 MPa at 11 T / 4.2 K”, HFM Annual Meeting, Feb. 2025, CERN. online.
  14. [14]G. Vallone, E. Anderssen, B. Bordini and P. Ferracin, ”A Review of the Mechanical Properties of Materials Used in Nb3Sn Magnets for Particle Accelerators,” in IEEE Transactions on Applied Superconductivity, vol. 33, no. 5, pp. 1-6, Aug. 2023, Art no. 4002806, doi: 10.1109/TASC.2023.3248544. https://ieeexplore.ieee.org/document/10050867DOI
  15. [15]P. Ferracin et al., ”Towards 20 T Hybrid Accelerator Dipole Magnets,” in IEEE Transactions on Applied Superconductivity, vol. 32, no. 6, pp. 1-6, Sept. 2022, Art no. 4000906, doi: 10.1109/TASC.2022.3152715. https://ieeexplore.ieee.org/document/9718198DOI
  16. [16]A. V. Zlobin and I. Noviski and E. Barzi and P. Ferracin, ”20 T Dipole Magnet Based on Hybrid HTS/LTS Cos-Theta Coils with Stress Management,” 2023 , 2305.06776. https://arxiv.org/abs/2305.06776
  17. [17]M. D’Addazio, P. Ferracin, Senior Member, IEEE, V. Marinozzi, E. Ravaioli, G. Vallone, and L. Savoldi, Member, IEEE, ”Conceptual Structural Design and Analysis of a 20 T Hybrid Cos-Theta Dipole for Future Particle Colliders”, IEEE Transactions on Applied Superconductivity, Vol. 35, No. 5, August 2025. https://ieeexplore.ieee.org/document/10786366
  18. [18]A. V. Zlobin, I. Novitski, E. Barzi, ”Conceptual Design of a HTS Dipole Insert Based on Bi2212 Rutherford Cable,” in Instruments 4, no. 4, 29. https://doi.org/10.3390/instruments4040029
  19. [19]A. D’Agliano et al., ”Magnetic and mechanical analysis of Bi-2212 Rutherford cable in a cos-theta sub-scale dipole coil”, 2025 Supercond. Sci. Technol., 38, 035021. https://iopscience.iop.org/article/10.1088/1361-6668/adb340DOI
  20. [20]A. V. Zlobin, I. Novitski, E. Barzi, and D. Turrioni, ”Development of a Small-Aperture Cos-Theta Dipole Insert Coil Based on Bi2212 Rutherford Cable and Stress Management Structure,” IEEE Transactions on Applied Superconductivity, vol. 32, no. 6, pp. 1-5, Sept. 2022, Art no. 4003605. https://ieeexplore.ieee.org/document/9734728DOI
  21. [21]A. V. Zlobin, I. Novitski, E. Barzi, and D. Turrioni, ”Development of a Bi2212 Dipole Insert at Fermilab,” in IEEE Transactions on Applied Superconductivity, vol. 33, no. 5, pp. 1-5, Aug. 2023, Art no. 4602305. https://ieeexplore.ieee.org/document/10092279DOI
  22. [22]E. Barzi, ”Conductor Properties and Coil Technology for a Bi2212 Dipole Insert for 20 Tesla Hybrid Accelerator Magnets”, Contribution to Snowmass 2021, Oct. 2022, https://doi.org/10.48550/arXiv.2204.01072
  23. [23]A. V. Zlobin et al., ”Development and First Test of the 15 T Nb3Sn Dipole Demonstrator MDPC1,” in IEEE Transactions on Applied Superconductivity, vol. 30, no. 4, pp. 1-5, June 2020, Art no. 4000805, doi: 10.1109/TASC.2020.296768. https://ieeexplore.ieee.org/document/8989965

Paper details

vlnc:W_unzv9jm3
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents