WorksPhysics and Astronomy
Analytical Modeling of characteristics using 2D Poisson Equations in AlN/-GaO HEMT
Abstract
In this paper, physics-based analytical models using two-dimensional (2D) Poisson equations for surface potential, channel potential, electric field, and drain current in AlN/-GaO high electron mobility transistor (HEMT) is presented. The analytical expression of different quantities is achieved based on full depletion approximation of the AlN barrier layer and polarization charge induced unified two-dimensional electron gas (2DEG) charge density model. For the validation of the developed model, results are compared with 2D numerical simulation results, and a good consistency is found between the two. The drain current model is also validated with experimental results of a similar dimension device. The developed model can be a good reference for different -GaO-based HEMTs.
Introduction
Nowadays, Gallium-oxide () is being explored for its possible application in the decade-old high electron mobility transistors (HEMTs) technology, currently dominated by III-nitride material like gallium-nitride (GaN). GaN HEMTs have shown excellent performance for high power and high-frequency applications on the back of exciting features such as higher two-dimensional electron gas (2DEG) density , very high 2DEG mobility . However, rising emerging applications like electric vehicles (EVs) and robotics have expanded the investigation horizon from wide bandgap (WBG) to ultra-wide bandgap (UWB) semiconductors. Among the UWB semiconductors, - is found to be more suitable for high voltage applications due to its ultra-large bandgap of , and breakdown field of . Moreover, - single crystal substrate can be grown using melt-based techniques, which ensures large size and affordable wafers for different device technologies.
To date, various - based experimental devices like Schottky diodes [1], [2], metal-oxide-semiconductor field-effect transistors MOSFETs[3]–[6], and -(AlGa)O/GaO (AGO/GO) HEMTs [7], [8] with excellent DC and RF performances have been reported. However, since - does not has any polarization property, and small band offset in AGO/GO HEMTs limit their performance as compared to their AlGaN/GaN counterpart. On the other hand, epitaxial layers of III-nitrides (AlN, GaN, InN) have been grown on - and potential AlN/- HEMT applications are anticipated [9]–[12]. Moreover, one of our previous works in AlN/-GaO HEMT estimated exceptional RF performance—cut-off frequency of 167 GHz, and output power of 2.91 W/mm [13]. Since the 2DEG density in HEMTs has a critical role in device operation, recently we have reported validation of estimated in AlN/-GaO HEMT through analytical modeling in [14]. Various physics-based models for different parameters in AlGaN/GaN HEMTs have been reported [15, 16, 17, 18, 19, 20], but almost none for -GaO-based HEMTs. Looking at the accuracy of the mathematical models over empirical and approximation models, device physics-based mathematical models for -GaO based HEMT will be useful to analyze and validate the estimated results. Here, we present physics-based mathematical models for surface potential and electric fields and extended them to get the current-voltage model in AlN/-GaO HEMT with an etched AlN barrier layer. For the validation of results, developed model results are compared with simulation as well as experimental results earlier published for similar -GaO devices.
Device Structure
The cross-sectional schematic of the analysed device is shown in Figure 1. The epi-layer sequence is as follows: on a semi-insulating -GaO substrate an n-type doped 100 nm -GaO buffer layer with /cm exists, followed by 10 nm AlN barrier layer which is undoped. Source and drain contacts are set as Ohmic with contact resistance of 0.4 -mm. The gate contact is assumed as Schottky and a barrier potential of 0.8 eV is set. The device dimensions are kept the same as [5] with gate length of 2.8 m, gate-drain spacing of 1.3 m, and gate-source spacing of 0.4 m. The gate width is equal to 100 m, and the output drain current is normalized with this quantity. In the simulation framework different physics-based models like Shockley-Read-Hall (SRH) recombination, Fermi-Dirac for carrier statistics, and negative differential conductivity (NDC) to capture electron velocity saturation effect are evoked. Default material parameters and spontaneous as well as piezoelectric polarization models are used from [21] for AlN barrier material. The -GaO material parameters used in the simulations and model development are taken from [22], [23], Table 1.
Figure 1. 2D cross-sectional view of AlN/-GaO HEMT.
| Symbol | Quantity | Values | Symbol | Quantity | Values |
| Energy bandgap | 4.9 eV | Valence band density | |||
| Electron affinity | 3.15 eV | Relative permittivity | 10 | ||
| Electron effective mass | Lattice constant | 3.04 | |||
| Density of states | Electron mobility | ||||
| Conduction band density | Hole mobility |
A list of symbols used in the model development is given in Table 2.
| Symbol | Quantity | Symbol | Quantity |
| Permittivity of AlN and -GaO material respectively | Unit electron charge | ||
| Thickness of AlN and -GaO layer respectively | Flat band voltage | ||
| Channel doping concentration | Built-in potential | ||
| Gate metal workfunction | Fermi potential | ||
| 2DEG density | Boltzmann constant | ||
| Threshold voltage | Conduction band offset | ||
| Thermal voltage | Electron affinity | ||
| Gate capacitance | Temperature |
Table 2. Symbols used in analytical modeling
A physics-based analytical model for surface potential, electric field, and drain current are developed by solving two-dimensional (2-D) Poisson’s equation in the channel region marked as Region I, II, and III as shown in Figure 1. The 2-D Poisson’s equation for the potential function (x, y) in the channel () is given by:
where , and are doping concentration and permittivity of -GaO buffer layer. Since potential at the AlN/-GaO interface is continuous, it is only solved for the region I, II, and III.
The potential function (x, y) along the y-direction in the channel can be approximated by a parabolic expression such as:
where are the surface potential, and are arbitrary constants for the region I, II, and III that are to be determined using boundary conditions. The Poisson’s equation (1) is solved simultaneously for all three regions in the channel using solution expressed in (3), and given as:
where , , and , , are the channel potential and surface potential in the channel in the region I, II, and III respectively. Furthermore, above equations (4), (5), and (6) are solved using the following boundary conditions for are given by:
where , where , since the AlN barrier layer is undoped.
Since -GaO does not possess any polarization property, the total polarization charge of the AlN/-GaO heterostructure is a sum of spontaneous as well as piezoelectric polarization of the AlN barrier layer. Total polarization of the AlN barrier , where spontaneous polarization [21], and piezoelectric polarization is calculated as given in [21]:
where , are lattice constants of AlN and -GaO; , and , are piezoelectric and elastic constants for AlN material respectively.
Based on full depletion of the AlN barrier layer, the polarization induced 2DEG charge density is given by [17]
where , and is the channel potential in regions I, II, III for , , . Furthermore, cut-off voltage is given as
Where is the Schottky barrier height; is the conduction band offset between AlN and -GaO at the heterointerface; is the total polarization charge density, and is the gate capacitance.
Since surface potential and the lateral electric field between the two consecutive regions at the heterointerface are continuous. The associated boundary conditions at the interface of region I-II and region II-III are given as
Now using boundary conditions of (7) to (12), all six constants of (4) to (6) are determined to get the AlN/-GaO HEMT channel potential as
Now substituting values of the channel potential obtained above in (1), new equations for the region I, II, and III are obtained as
For region I ()
For region II ()
For region III ()
The solutions of equations (26) – (28) are obtained using the sum of complementary function (CF) and particular integral (PI) and given as follows
Where
Now the constants of (29) – (31) are calculated using boundary conditions given in (13), (14) and (19) – (22), and given as
Analysis of Surface Potential, Channel Potential, Electric Field, and Drain Current
Now the surface potential for the entire channel length ( to ) using (29), (30), (31) is given as
Furthermore, using (23), (24), and (25) and substituting , the channel potential for entire channel length ( to ) is given as
where channel potential for the region I, II, and III are given as
The lateral electric field along the 2DEG channel can be defined as
And from to , the component of the electric field is given as
Where lateral electric field components in the region I, II, III are obtained using (42), (43), (44) and (45) given as
The drain current density is given as follows
Where is the gate width, is the electron effective velocity, and is given as
Where electron mobility is given as per the negative differential mobility model from [21]
For -GaO, the parameters cm/Vs, cm/s, critical field V/cm, and are taken from [24]. After substituting from (17), the drain current given by (51) can be rewritten as
Results and Discussion
The simulation results for the device structure (Figure 1) are obtained using the 2D device simulator—ATLAS [21]. The physics-based models and material properties are discussed in previous sections. The device simulator is first calibrated with experimental results measured in [5]. The mathematical model data are obtained using the computational tool—MATLAB [25]. The surface potential profile, channel potential, and electric field profile are extracted from structure files saved at different bias voltages. The surface potential plots are shown in Figure 2. These data are extracted from at the heterointerface of different structure files for three different of 1 V, V, and V and constant of 10 V. The computed data from derived model (41) are also shown.
Figure 2. The surface potential at the AlN/-GaO interface for different , , V at fixed V. Full channel length subdivided into , , and is also drawn in the lower part of the figure.
The channel potential and electric field simulated data are extracted in the channel 5 nm below the interface. The model data for channel potential and electric field are computed from (42), and (47) respectively. Simulated and model data for channel potential and electric field are shown in Figure 3, and Figure 4 respectively.
Figure 3. Simulated and modeled data of channel potential along the channel below 5 nm from heterointerface for different , , V at fixed V. The plot is almost similar to surface potential plot except under in the latter.
Figure 4. Lateral electric field along the channel below 5 nm from heterointerface for different , , V at fixed V. Peak electric field of V/cm is evident under the drain side gate edge.
The transfer characteristic of the proposed device is shown in Figure 5. Drain current model data and experimental result relating to similar dimension device is also indicated. Except for the sub-threshold region, there is a good consistency between model data and simulation results. Additionally, a fair degree of agreement is evident with experimental data reported in [5].
Figure 5. Simulated, Experimental, and modeled data of – characteristics of the analysed device.
Conclusion
The analytical model of surface potential, channel potential, and electric field for is presented. The 2D Poisson equation is solved to develop an expression of potential and lateral field along the channel and consequently extended to find expression of drain current. For the validation of the simulation and model data, the simulation deck is calibrated with device dimensions similar to the experimental one as reported elsewhere. Analytical model data of surface potential, channel potential, and electric field are rigorously validated with different values of gate voltages. Furthermore, drain current model results are compared with simulation results as well as validated by experimental data. A good level of agreement among all three is obtained. Further work in the physics-based analytical models for the -based devices can be helpful to understand device mechanism and useful to predict its potential for futuristic high power applications.
References
- [1]Z. Hu et al., “Field-Plated Lateral β-Ga2O3 Schottky Barrier Diode with High Reverse Blocking Voltage of More Than 3 kV and High DC Power Figure-of-Merit of 500 MW/cm2,” IEEE Electron Device Lett., pp. 1–1, 2018, doi: 10.1109/LED.2018.2868444.DOI
- [2]J. Yang, F. Ren, M. Tadjer, S. J. Pearton, and A. Kuramata, “Ga2O3 Schottky rectifiers with 1 ampere forward current, 650 V reverse breakdown and 26.5 MW.cm-2 figure-of-merit,” AIP Adv., vol. 8, no. 5, 2018, doi: 10.1063/1.5034444.DOI
- [3]M. Higashiwaki et al., “Depletion-mode Ga2O3 metal-oxide-semiconductor field-effect transistors on β-Ga2O3 (010) substrates and temperature dependence of their device characteristics,” Appl. Phys. Lett., vol. 103, no. 12, pp. 1–5, 2013, doi: 10.1063/1.4821858.DOI
- [5]Z. Xia et al., “Delta Doped β-Ga2O3 Field Effect Transistors With Regrown Ohmic Contacts,” IEEE Electron Device Lett., vol. 39, no. 4, pp. 568–571, Apr. 2018, doi: 10.1109/LED.2018.2805785.DOI
- [6]Z. Feng et al., “Normally-Off-β-Ga2O3 Power MOSFET with Ferroelectric Charge Storage Gate Stack Structure,” IEEE Electron Device Lett., vol. 41, no. 3, pp. 333–336, 2020, doi: 10.1109/LED.2020.2970066.DOI
- [7]S. Krishnamoorthy et al., “Modulation-doped (β-Al 2 O 3) 2 O 3 / Ga 2 O 3 field-effect transistor,” Appl. Phys. Lett., vol. 111, no. 2, pp. 023502, Jul. 2017, doi: 10.1063/1.4993569.
- [8]Y. Zhang et al., “Demonstration of high mobility and quantum transport in modulation-doped β-(AlxGa1-x)2O3/Ga2O3 heterostructures,” Appl. Phys. Lett., vol. 112, no. 17, pp. 1–6, 2018, doi: 10.1063/1.5025704.DOI
- [9]W. Wei et al., “Valence band offset of β-Ga2O3/wurtzite GaN heterostructure measured by X-ray photoelectron spectroscopy,” Nanoscale Res. Lett., vol. 7, no. 1, p. 562, 2012, doi: 10.1186/1556-276X-7-562.DOI
- [12]S. Lyu and A. Pasquarello, “Band alignment at β -Ga 2 O 3 /III-N (III = Al, Ga) interfaces through hybrid functional calculations,” Appl. Phys. Lett., vol. 117, no. 10, p. 102103, Sep. 2020, doi: 10.1063/5.0020442.DOI
- [13]R. Singh, T. R. Lenka, R. T. Velpula, B. Jain, H. Q. T. Bui, and H. P. T. Nguyen, “A novel β-Ga2O3 HEMT with fT of 166 GHz and X-band POUT of 2.91 W/mm,” Int. J. Numer. Model. Electron. Networks, Devices Fields, vol. 34, no. 1, pp. 1–11, 2021, doi: 10.1002/jnm.2794.DOI
- [14]R. Singh, T. R. Lenka, and H. P. T. Nguyen, “Analytical Study of Conduction Band Discontinuity Supported 2DEG Density in AlN/β-Ga2O3 HEMT,” Facta Universitatis, Series: Electronics and Energetics, 06 May 2021. (Accepted, in press)
- [15]S. P. Kumar, A. Agrawal, R. Chaujar, S. Kabra, M. Gupta, and R. S. Gupta, “Threshold voltage model for small geometry AlGaN/GaN HEMTs based on analytical solution of 3-D Poisson’s equation,” Microelectronics J., vol. 38, no. 10–11, pp. 1013–1020, 2007, doi: 10.1016/j.mejo.2007.09.001.DOI
- [16]S. Khandelwal, N. Goyal, and T. A. Fjeldly, “A physics-based analytical model for 2DEG charge density in AlGaN/GaN HEMT devices,” IEEE Trans. Electron Devices, vol. 58, no. 10, pp. 3622–3625, 2011, doi: 10.1109/TED.2011.2161314.DOI
- [17]S. Khandelwal and T. A. Fjeldly, “A physics based compact model of I-V and C-V characteristics in AlGaN/GaN HEMT devices,” Solid State. Electron., vol. 76, pp. 60–66, 2012, doi: 10.1016/j.sse.2012.05.054.DOI
- [18]F. M. Yigletu, S. Khandelwal, T. A. Fjeldly, and B. Iniguez, “Compact charge-based physical models for current and capacitances in AlGaN/GaN hemts,” IEEE Trans. Electron Devices, vol. 60, no. 11, pp. 3746–3752, 2013, doi: 10.1109/TED.2013.2283525.DOI
- [19]M. Kaddeche, A. Telia, and A. Soltani, “Analytical modeling and analysis of Al m Ga1-mN/GaN HEMTs employing both field-plate and high-k dielectric stack for high-voltage operation,” J. Comput. Electron., vol. 12, no. 3, pp. 501–510, 2013, doi: 10.1007/s10825-013-0468-5.DOI
- [20]S. Khandelwal, S. Ghosh, Y. S. Chauhan, B. Iniguez, and T. A. Fjeldly, “Surface-Potential-Based RF Large Signal Model for Gallium Nitride HEMTs,” 2015 IEEE Compd. Semicond. Integr. Circuit Symp. CSICS 2015, pp. 1–4, 2015, doi: 10.1109/CSICS.2015.7314527.DOI
- [21]Device Simulation Software, ATLAS User’s Manual, Silvaco, Santa Clara, CA, USA, 2019.
- [22]A. Mock et al., “Band-to-band transitions, selection rules, effective mass, and excitonic contributions in monoclinic β-Ga 2 O 3,” Phys. Rev. B, vol. 96, no. 24, pp. 1–14, 2017, doi: 10.1103/PhysRevB.96.245205.DOI
- [23]S. Poncé and F. Giustino, “Structural, electronic, elastic, power, and transport properties of β-Ga2O3 from first principles,” Physical Review Research, vol. 2, no. 3. p. 033102, 2020, [Online]. Available: https://link.aps.org/doi/10.1103/PhysRevResearch.2.033102.DOI
- [24]K. Ghosh and U. Singisetti, “Ab initio velocity-field curves in monoclinic β-Ga 2 O 3,” J. Appl. Phys., vol. 122, no. 3, p. 035702, Jul. 2017, doi: 10.1063/1.4986174.DOI
- [25]MATLAB Version 7.10.0 (R2018a). Natick, Massachusetts: The MathWorks Inc.; 2018.