betaFeedback

WorksPhysics and Astronomy

A new semiconducting perovskite alloy system made possible by gas-source molecular beam epitaxy

Abstract

Optoelectronic technologies are based on families of semiconductor alloys. It is rare that a new semiconductor alloy family is developed to the point where epitaxial growth is possible; since the 1950s, this has happened approximately once per decade. Here we demonstrate epitaxial thin film growth of semiconducting chalcogenide perovskite alloys in the Ba-Zr-S-Se system by gas-source molecular beam epitaxy (MBE). We stabilize the full range y = 0 ... 3 of compositions BaZrS(3−y)_{(3-y)}Sey_y in the perovskite structure, up to and including BaZrSe3_3, by growing on BaZrS3_3 epitaxial templates. The resulting films are environmentally stable and the direct band gap (EgE_g) varies strongly with Se content, as predicted by theory, covering the range EgE_g = 1.9 ... 1.4 eV for yy = 0 ... 3. This creates possibilities for visible and near-infrared (VIS-NIR) optoelectronics, solid state lighting, and solar cells using chalcogenide perovskites.

Each new family of semiconductors expands opportunities for technological innovation, as new property combinations become available. Alloy families are selected based on their different properties for different applications, from cameras, to solar cells, to telecommunications, and so on. Device engineering and optimization are then achieved through the fine control of composition and electronic structure made possible by epitaxial film growth. Chalcogenide perovskites are notable for their high dielectric polarizability, chemical and environmental stability, and wide range of theoretically-predicted EgE_g.[1]

By perovskite, we refer to phases with composition ABX3ABX_3, with structure characterized by corner-sharing BX6BX_6 octahedra (including distorted perovskites, with ∠(B−X−B)≠180∘\angle(B-X-B) \ne180^\circ). Most ABX3ABX_3 chalcogenides with X=S,SeX = \mathrm{S}, \mathrm{Se} are thermodynamically unstable in the perovskite structure, and instead form edge- and face-sharing structures with needle-like crystals.[2] The most-studied chalcogenide perovskite is BaZrS3\mathrm{BaZrS}_3 (distorted perovskite structure, orthorhombic space group PnmaPnma). It can be prepared by high-temperature bulk and thin film growth methods, including MBE, and it is very stable, even against heating in air above 500 °C.[3, 4, 5] It has a direct band gap of Eg=1.9E_g = 1.9 eV and absorbs light strongly.[3] For VIS-NIR optoelectronic applications, solid state lighting, and solar energy conversion, a range of EgE_g is necessary. Theory predicts that Se-alloying rapidly decreases EgE_g, to as low as ≈1.3\approx1.3 eV in the pure selenide.[6, 7, 8] This would make BaZrS(3−y)Sey\mathrm{BaZrS}_{(3-y)}\mathrm{Se}_y perovskite alloys particularly attractive for thin-film solar cells. However, $\mathrm{BaZrSe}_3 is not stable in the perovskite structure. Theory predicts that the edge-sharing, needle-like structure with Eg≈1E_g \approx1 eV is the most stable, whereas synthesis attempts yielded a hexagonal, defect-ordered phase with metallic conductivity.[6, 8, 9, 10] Powder synthesis results demonstrate that BaZrS(3−y)SeyBaZrS_{(3-y)}Se_y is stable in the bulk up to at least y=1.2y = 1.2 (40% Se).[11]

The gas-source MBE method, that we introduced recently for making BaZrS3BaZrS_3 epitaxial thin films, is suited for expanding into alloy development. We use varying quantities of H2SH_2S and H2SeH_2Se gas flows to make films with varying S:SeS:Se ratio, up to and including the selenide perovskite BaZrSe3BaZrSe_3 with Eg=1.4±0.1E_g = 1.4 \pm0.1 eV. Our approach represents a revival of methods for making epitaxial films of chalcogenide compound semiconductors by gas-source MBE, developed decades ago for II-VI semiconductors. These methods are newly relevant because of heightened interest in semiconductor fabrication: for chalcogenide perovskites, two-dimensional materials, and other materials for computing, optoelectronics, and energy conversion.

abscissa is the pseudo-cubic lattice constant (aPCa_{PC}); horizontal error bars represent composition variation through the film thickness.

In Figure 1 we show the band gap (EgE_g) and lattice constant measured on five BaZrS3−y_{3-y}Sey_y films spanning y=0…3y = 0 \ldots3 and aPC=4.996±0.004…5.34±0.09a_{PC} = 4.996 \pm0.004 \ldots5.34 \pm0.09 Å, along with data for other semiconducting materials. For the chalcogenide perovskites, we plot the pseudo-cubic lattice constant (aPCa_{PC}), determined from X-ray diffraction (XRD) measurements of the (202) reflection, and EgE_g is determined from photoconductivity spectroscopy (PCS). Plots such as these of EgE_g vs. lattice constant (called a “Cho plot”, after the developer of MBE) are the starting point for designing optoelectronics, solid-state lighting, and solar cells. The advent of epitaxial growth of BaZrS3−y_{3-y}Sey_y alloys with tunable EgE_g means that chalcogenide perovskites may reasonably be placed on a Cho plot, alongside well-established families of semiconductors. Se alloying is effective at reducing EgE_g into the range needed for single-junction solar cells. EgE_g may also be raised above 2 eV, into the green lighting region, in compounds containing Sr and/or Hf.[11, 12] To-date such materials have been reported only as powders made by solid-state synthesis; alloys and thin-film epitaxy have not been demonstrated. Nevertheless, we indicate these materials in Figure 1, to suggest that the chalcogenide perovskite alloy family may in the future cover a wide range of EgE_g.[1]

Figure 1. Cho plot representing chalcogenide perovskites as a new family of semiconductor alloys. Deep blue points represent the BaZr(S,Se)3BaZr(S,Se)_3 alloy series reported here as epitaxial thin films. Light blue points represent other chalcogenide perovskites, reported elsewhere as solid-state synthesis of bulk powders. Other data are established semiconductors and alloy families. Direct (indirect) band gap alloys are indicated by solid (dashed) lines. The colored band indicates the range of EgE_g appropriate for single-junction solar cells. For the chalcogenide perovskites, the

We grow films by pseudomorphic epitaxy on BaZrS3_3 template layers, leveraging our previously-reported process for epitaxial growth of BaZrS3_3 on LaAlO3_3 (LAO) substrates.[3] Due to the high growth temperature, there is substantial intermixing of S and Se between the growing BaZrS3−y_{3-y}Sey_y film and the underlying BaZrS3_3 layer. As a result, the final composition throughout the entire film (including the original template layer) is closely determined by the ratio of H2_2Se and H2_2S gases in the vapor phase during the alloy growth stage. This facile anion exchange process is why we refer to the initial BaZrS3_3 film as a template layer, instead of a buffer layer. We use the relative concentrations of H2_2Se and H2_2S in the vapor phase to determine the nominal composition parameter yy. As shown below, this nominal composition parameter closely predicts the actual film composition, as measured by scanning transmission electron microscopy energy dispersive X-ray spectroscopy (STEM-EDX). Reflection high-energy electron diffraction (RHEED) data acquired during growth shows evidence of single crystalline, perovskite epitaxial films. In Figure 2a we present RHEED data measured along the [100]LAO−PC_{\mathrm{LAO-PC}} azimuth during growth of BaZrS3_3, BaZrS2_2Se (y=1y = 1) and BaZrSe3_3 (y=3y = 3) (LAO-PC indicates pseudo-cubic indexing of the LAO crystal structure). The RHEED pattern does not change when the growth is switched from BaZrS3_3 to BaZrS3−y_{3-y}Sey_y, indicating epitaxial growth of the same crystal structure albeit different composition (i.e., pseudomorphic heteroepitaxy). The pattern remains streaky, without sign of discrete points, indicating atomically-smooth film growth. X-ray reflectivity (XRR) and atomic force microscopy (AFM) analysis also show that the top surface and the buried interfaces are smooth (Figure S1).

Diffraction patterns and reciprocal space maps for BaZrS3, BaZrS2Se, and BaZrSe3 films

Figure 2. Diffraction demonstrates pseudomorphic heteroepitaxy. (a) RHEED data measured along [100] pseudocubic axis of the LAO substate for a BaZrS3_3 template layer on LAO, a BaZrS2_2Se film, and a BaZrSe3_3 film. The long diffraction streaks indicate atomically-smooth surfaces, and the streak alignments indicate pseudomorphic epitaxial alloy growth on the BaZrS3_3 template. (b-c) RSMs for BaZrS2_2Se, BaZrSSe2_2, and BaZrSe3_3 films, all on BaZrS3_3 templates. (b) Out-of-plane (202) reflection; white dashed line shows the position of the relaxed, pure BaZrS3_3. (c) In-plane (121) reflection.

XRR and AFM data

Figure S1. (a) XRR and (b) AFM data. The samples have r.m.s. roughness of 2.19±0.542.19 \pm0.54 nm (y=1y = 1), 1.52±0.381.52 \pm0.38 nm (y=1.3y = 1.3), and 0.83±0.270.83 \pm0.27 nm (y=2y = 2), and 2.63±2.342.63 \pm2.34 nm (y=3y = 3).

We present in Figure 2b reciprocal space maps (RSMs) of the out-of-plane (202) film reflections. The lattice constant of BaZrS3−y_{3-y}Sey_y expands with yy, so that the alloy and selenide (202) reflections appear at lower qzq_z than for the sulfide BaZrS3_3. The RSMs show the presence of two (202) reflections, indicative of regions in the film with different d-spacings; out-of-plane, high-resolution x-ray diffraction (HRXRD) measurements also showed two (202) peaks (Figure S2). STEM results (discussed below) reveal that this peak splitting derives from film microstructure. In Figure 2c we present RSMs of the (121) reflections, containing both in- and out-of-plane contributions.

HR XRD data of BaZrS(3-y)Sey alloy series

Figure S2. HR XRD data of BaZrS(3−y)Sey\mathrm{BaZrS}_{(3-y)}\mathrm{Se}_{y} alloy series (y=1y = 1, 1.3, 2 and 3). The (012), (024) and (036) reflections labeled in grey are from the LaAlO3\mathrm{LaAlO}_{3} substrate.

We use STEM to investigate the local microstructure, crystal structure, and composition for two representative samples BaZrS2_2Se (y=1y = 1) and BaZrSSe2_2 (y=2y = 2). In Figure 3a and Figure 3b we present high angle annular dark-field (HAADF) images, measured along the [10]LAO−PC_{\mathrm{LAO-PC}} zone axis, that includes the substrate, template layer, and top layer. The substrate/template interface is abrupt and we observe the presence of two epitaxial growth modes, as reported previously.[3] The dominant epitaxial growth mode for BaZrS3_3 films on LAO is via a self-assembled, incoherent buffer layer, enabling fully-relaxed films despite the large lattice constant mismatch.[3] The interface between the bottom, template layer (grown as BaZrS3_3) and the top, alloy layer is coherent. Therefore, during alloy growth the top layer induces tensile strain in the template layer, and the template layer places the top layer under compressive strain.

STEM measurements of structure and composition

Figure 3. STEM measurements of structure and composition. HAADF-STEM image of a typical film cross section of (a) BaZrS2_2Se (y=1y = 1) sample and (b) BaZrSSe2_2 (y=2y = 2). The interface between the bottom layer and the top layer is visible as a change in the distribution of vertical and horizontal APBs. (c) In-plane (left) and out-of-plane (right) cation-cation distances corresponding to the HAADF-STEM image in (b). (d) S and Se atomic concentrations, determined by EDX, through the film thickness for both films.

These strains appear to control the formation of Ruddlesden Popper (RP) faults or antiphase boundaries (APBs). APBs in perovskites manifest as rock-salt-like layers that disrupt the corner-sharing octahedral connectivity, and are related to layered phases such as the Ruddlesden-Popper series. APBs can accommodate cation off-stoichiometry and relieve strain.[13, 14] We observe APBs in our chalcogenide perovskite epitaxial films, which we ascribe to the difficulty of maintaining exact Ba:Zr = 1:1 stoichiometry during MBE synthesis, without an accessible parameter regime of growth by self-limited adsorption.[15] Here we observe an additional effect: in the bottom layer we observe mostly vertical APBs, whereas in the top layer we observe a high concentration of horizontal APBs. As the Ba:Zr supply rates are unchanged throughout, we hypothesize that this change in the APB profile is related to strain relaxation. The vertical APBs in the bottom help to relieve the tensile strain imposed by the overlying film. By the same logic, as the top overlayer is under compressive strain from the underlying bottom, there is a preference for APBs to orient horizontally. The APB profile illustrates clearly the location of the bottom/top interface, despite chalcogen intermixing. This is sensible, as the diffusivity of two-dimensional extended defects is infinitesimal compared to that of individual chalcogen ions: the APBs nucleate and grow simultaneously with ad-atom attachment, while S2−^{2-} and Se2−^{2-} ions may migrate throughout the whole time of film growth.

The APBs locally modulate the d-spacing, and explain the reflection pairs observed in XRD. In Figure 3c we present in-plane and out-of-plane cation-cation distances for sample BaZrSSe2_2 (y=2y = 2) determined by STEM.[16] These are the average of Ba-Ba and Zr-Zr distances; data for sample BaZrS2_2Se (y=1y = 1) and additional analysis are presented in Figure S3. Horizontal APBs create a tripartite population of out-of-plane cation-cation distances in the top layer, corresponding to expansion in the APB core, compression immediately adjacent to the APB core, and an intermediate value away from APBs. The net effect is that the film has regions of distinct dd-spacing, despite nearly-uniform composition throughout, due to the presence of APBs. Histograms of the cation-cation spacing measured by STEM (Figure S3) are in quantitative agreement with the reflection pairs observed in RSM (Figure 2b-Figure 2c) and HRXRD (Figure S2).

Image not extracted

Figure S3. Local cation-cation spacing measured by STEM on samples BaZrS2_2Se (y = 1 film) and BaZrSSe2_2 (y = 2). Colormaps show average of Ba-Ba and Zr-Zr spacings (pm). (a) Out-of-plane spacings. In the top layer, the presence of horizontal APBs results in a broad distribution with multiple peaks, corresponding to different regions of the film. In contrast, the spacings in the bottom layer are more narrowly distributed. For the case y = 2, a tripartite distribution in the top layer is easily modeled: (i) 593 pm within the APBs, (ii) 492 pm, immediately around the APBs, and (iii) 533 pm, away from the APBs. The dashed lines and accompanying labels indicate the d-spacing of the twin peaks observed in XRD. (b) In-plane spacings. In this case, the distribution is broader for the bottom layer, due to the presence of vertical APBs.

In Figure 3d we show STEM-EDX depth-dependent composition profiles. Interestingly, the films have a near-uniform composition from the substrate to the top surface, with Se/S ratio close to the gas conditions during alloy growth. The boundary between the bottom, template layer and the top layer is clear in STEM images due to the APB pattern (Figure 3a-Figure 3b), but is nearly-imperceptible in the composition profiles. We conclude that S and Se readily diffuse and mix at the film growth temperature, resulting in the conversion of the BaZrS3\mathrm{BaZrS}_{3} template layer into a BaZrS(3−y)Sey\mathrm{BaZrS}_{(3-y)}\mathrm{Se}_{y} alloy, without disrupting the crystal structure or film microstructure.

We use PCS to measure how EgE_g varies with composition. Optical measurement techniques including spectrophotometry and ellipsometry can accurately measure EgE_g for uniform thin films, especially for materials with direct band gap and strong light absorption, such as chalcogenide perovskites.[3, 11] However, for films with known variation in composition and EgE_g from top to bottom, optical methods are not advisable. PCS is sensitive to the layer with the smallest EgE_g in a multilayer stack (this is why external quantum efficiency measurements are often used to measure EgE_g of the absorber in thin-film solar cells). We fabricated photodetectors by depositing interdigitated Ti/Au electrodes on the film surface, and we measured the spectral responsivity (the ratio of photocurrent to incident light power) using a tunable light source. In Figure 4a we show the normalized responsivity spectra. The responsivity onset tracks the reduction of EgE_g with increasing yy. We derive EgE_g by extrapolating linear fits to the responsivity immediately above the onset energy, and we present the results in Figure 4b alongside published experimental and theoretical values.[3, 7, 11, 17] For the pure sulfide BaZrS3\mathrm{BaZrS}_{3} we find Eg=1.82±0.08E_g = 1.82 \pm0.08 eV, agreeing with the value of 1.9 eV determined optically.[3] EgE_g decreases rapidly with Se content, reaching 1.4±0.11.4 \pm0.1 eV for BaZrSe3\mathrm{BaZrSe}_{3}, confirming theoretical predictions of the effect of Se alloying of BaZrS3\mathrm{BaZrS}_{3}.[7, 17] The absolute photodetector responsivity decreased monotonically by several orders of magnitude with increasing Se content, going from 400 mA/W for the y=1y = 1 detector, to 0.04 mA/W for the y=3y = 3 detector (Figure S5). This reduction in responsivity indicates a decreasing mobility-lifetime product with increasing Se alloying, which will be addressed through defect engineering in future work.

Figure 4. Variation of band gap (EgE_g) with Se content, measured by PCS. (a) PCS responsivity spectra measured on BaZrS(3−y)Sey\mathrm{BaZrS}_{(3-y)}\mathrm{Se}_y photodetectors. (b) EgE_g vs. composition, measured here and as reported elsewhere. Nishigaki [11]: optical measurements on powder samples of BaZrS3\mathrm{BaZrS}_3 and BaZrS(3−y)Sey\mathrm{BaZrS}_{(3-y)}\mathrm{Se}_y, y=1.2y = 1.2.[11] Sadeghi [3]: optical measurements on BaZrS3\mathrm{BaZrS}_3 epitaxial thin films.[3] Meng [7] and Li [17] reported theoretical predictions.[7, 17]

Absolute responsivity and EQE of photodetectors, and STEM HAADF image

Figure S5. (a) Absolute responsivity and EQE of polycrystalline BaZrS3\mathrm{BaZrS}_{3} (hollow circle marker) as well as epitaxial BaZrS(3−y)Sey\mathrm{BaZrS}_{(3-y)}\mathrm{Se}_{y} (solid circles markers) photodetectors at illumination wavelength of 600 nm for varying composition. (b) STEM HAADF image along the film [110]PC[110]_{\mathrm{PC}} zone of the non-epitaxial polycrystalline pure-sulfide film deposited on sapphire, with inset showing the corresponding Ba and Zr atom columns. Several crystal orientations are visible, with many twin boundaries present.

Our results are notable for demonstrating an alloy family of perovskite semiconductors that can be grown as epitaxial thin films with continuously-variable direct band gap. Chalcogenide perovskites are stable and are made of inexpensive, and low-toxicity elements.[5] Hanzawa et al. demonstrated that chalcogenide perovskites can be chemically doped both nn- and pp-type, and our results published elsewhere suggest slow excited-state recombination and fast charge mobility.[12, 18, 19, 20] The phenomenon of anion (S2−\mathrm{S}^{2-}, Se2−\mathrm{Se}^{2-}) diffusion and mixing observed here suggests that alloy composition and band gap can be controlled by annealing in controlled environments. These reports motivate continued work towards optoelectronic and energy conversion devices based on chalcogenide perovskites, including thin-film solar cells. The most outstanding obstacle to chalcogenide perovskite-based technology may be lowering the temperature required for synthesis of high-quality films.

Methods

We grow films using a gas-source MBE system (Mantis Deposition M500). The substrate is heated radiatively from a SiC filament and is rotated at 2 rpm. Ba metal is supplied from an effusion cell (Mantis Comcell 16-500), and Zr metal from an electron beam (e-beam) evaporator (Telemark model 578). We calibrate Ba and Zr source rates using a quartz crystal monitor at the substrate position, and X-ray reflectivity (XRR), X-ray photoelectron spectroscopy (XPS) and X-ray fluorescence (XRF) measurements after film growth. Sulfur and selenium are supplied in the form of H2S\mathrm{H_2S} and H2Se\mathrm{H_2Se} gases (Matheson). These are supplied from condensed, liquified sources of 99.9% and 99.998% purity, respectively, and pass-through point-of-use purifiers (Matheson Purifilter) before entering the MBE chamber. The gases are injected in close proximity to the substrate using custom-made gas lines and nozzles.

We deposit films on (001)PC_{\mathrm{PC}}-oriented LaAlO3\mathrm{LaAlO_3} (PC stands for pseudo-cubic) single-crystal substrates (CrysTec GmbH). We outgas the substrates in the MBE chamber at 1000 °C in H2S\mathrm{H_2S} gas. The growth temperature measured at the thermocouple was 1000 °C. We first grow a template layer of BaZrS3\mathrm{BaZrS_3}, approximately 20 nm thick. We then interrupt deposition, start the H2Se\mathrm{H_2Se} flow, adjust the H2S\mathrm{H_2S} flow, and resume growth. The H2S\mathrm{H_2S} flow rate is 0.8 sccm during substrate outgassing and buffer layer growth. During BaZrS(3−y)Sey\mathrm{BaZrS_{(3-y)}Se_y} film growth, the H2S\mathrm{H_2S} and H2Se\mathrm{H_2Se} flow rates were adjusted to achieve the desired chalcogen ratio in the gas phase. We measure and control gas flow rates using mass flow controllers (MFCs, Brooks GF100C).

The chalcogen ratio in the gas phase is determined using a residual gas analyzer (RGA, Inficon Transpector 2.0). The H2S\mathrm{H_2S} and H2Se\mathrm{H_2Se} signals appear in the RGA data at 34 Da and 81 Da, respectively (both singly-ionized). We use the relative intensity of these signals to define the composition variable yy, used throughout this work. The relationship between gas flow rates measured by the mass flow controllers (MFCs) and chalcogen ratio measured by the RGA is nonlinear. To achieve H2S/H2Se=2\mathrm{H_2S/H_2Se}=2 (composition y=1y=1), the H2S\mathrm{H_2S} and H2Se\mathrm{H_2Se} flow rates were 0.6 sccm and 0.1 sccm, respectively (a ratio of 6). To achieve H2S/H2Se=0.5\mathrm{H_2S/H_2Se}=0.5 (composition y=2y=2), the H2S\mathrm{H_2S} and H2Se\mathrm{H_2Se} flow rates were 0.3 and 0.36 sccm, respectively (a ratio of 0.83). For BaZrSe3\mathrm{BaZrSe_3} (y=3y=3), we use an H2Se\mathrm{H_2Se} flow of 0.5 sccm and no H2S\mathrm{H_2S}. The chamber pressure during film growth is approximately 8×10−58\times10^{-5} torr. The film growth rate is 0.1 Å/s. We maintain H2S\mathrm{H_2S} and H2Se\mathrm{H_2Se} gas flows during cooldown, after growth, to avoid unwanted S and Se desorption. The typical total thickness of the film is approximately 40 nm.

The RGA measurements of H2S\mathrm{H_2S} and H2Se\mathrm{H_2Se} gas-phase concentrations are affected by the relative ionization efficiency of these gases in the RGA. Therefore, the RGA data is likely not an accurate representation of the relative partial pressures in the chamber. H2Se\mathrm{H_2Se} is less thermodynamically stable than H2S\mathrm{H_2S}. The observation that the H2S/H2Se\mathrm{H_2S/H_2Se} ratio observed in RGA data is lower than that determined by MFC flow rates may be explained by more effective ionization of H2Se\mathrm{H_2Se}. However, it is interesting to note that the RGA data (that determines yy) closely tracks the final composition of the films. We suggest that the relative thermodynamic instability of H2Se\mathrm{H_2Se} affects both ionization efficiency (in the RGA) and solid-vapor reaction rates (at the growing film) to similar extents.

As an alternative to using RGA data, the relative concentrations of H2S\mathrm{H_2S} and H2Se\mathrm{H_2Se} in the chamber can be determined by measuring total chamber pressure with different flow rates, using a cold-cathode vacuum gauge (Inficon Gemini). We find that this approach produces similar results as using the RGA.

We measure RHEED data using a 20 keV, differentially-pumped electron gun (Staib) and a digital acquisition system (k-Space Associates, kSA 400). We perform X-ray reflectivity (XRR) measurements using a Rigaku Smartlab, with a Cu target, and a tube power of 9 kW (45 kV, 200 mA). We perform out-of-plane XRD using a Bruker D8 High-Resolution X-ray diffractometer with a Ge (022) four-bounce monochromator in parallel-beam mode, with a Cu target, and a tube power of 1.6 kW (40 kV, 40 mA). We measured RSMs using a Bruker D8 Discover GADDS with a Co Kα_\alpha source, ¼ Eulerian cradle, and Vantec-2000 area detector. RSMs were collected with tilts of 0° and 45° for symmetric and asymmetric scans, respectively. The GADDS data were transformed to reciprocal coordinates using Bruker Leptos 7.3 software. Atomic force microscopy (AFM) measurements were performed using a Bruker Icon, and the images were processed using Gwyddion software. PCS was performed on photodetector samples fabricated by sputtering 5 nm Ti/200 nm Au interdigitated contacts on the films. The interdigitated contacts had eight individual fingers, each 5 mm long, with finger spacing and width of 100 µm. We used a tunable light source with a 300 W Xe arc lamp (ScienceTech), providing irradiance between 50 to 200 µW/cm2^2 depending on the selected wavelength. We used a source-meter (Keithley 2400-C) to source a bias of 4 V and measure the resulting photocurrent.

We prepared samples for STEM using nonaqueous wedge polishing, followed by single-sector ion milling (Fischione 1051) using ion-beam energies of 3, 2, and then 1 kV. We performed STEM imaging on a Thermo-Fischer Scientific Themis Z (probe-corrected, accelerating voltage = 200 kV, convergence angle = 17.9 mrad, beam current = 30 pA). STEM-EDX was performed using the Super X detectors (beam current = 100 pA) and quantified via Thermo-Fisher Scientific Velox software, using both pre- and post-filtering (Gaussian blur, sigma = 1.6). The net intensity profile was processed through a 15 pt adjacent averaging smoothing using Origin software to highlight the trends across the sample. STEM-EELS was performed using a Gatan Continuum spectrometer (sample thickness ≈\approx 40nm) dispersion = 0.75 eV ch−1^{-1}) and processed via the HyperSpy python package.

Acknowledgements

We acknowledge support from the National Science Foundation (NSF) under grant no. 1751736, "CAREER: Fundamentals of Complex Chalcogenide Electronic Materials”. A portion of this project was funded by the Skolkovo Institute of Science and Technology as part of the MIT-Skoltech Next Generation Program. K.Y. and J.v.S. acknowledge support by the NSF Graduate Research Fellowship, grant no. 1745302. J.M.L. acknowledges support from the Air Force Office of Scientific Research (FA9550-20-0066). T.S. and V.N. acknowledge support from the SFI Centre for Doctoral Training in Advanced Characterisation of Materials (CDT-ACM) (SFI Award reference 18/EPSRC-CDT/3581). This work was carried out in part through the use of the MIT Materials Research Laboratory and MIT.nano facilities.

References

Supplementary information for “A new semiconducting perovskite alloy system made possible by gas-source molecular beam epitaxy”

Ida Sadeghi; Jack Van Sambeek; Tigran Simonian; Michael Xu; Kevin Ye; Valeria Nicolosi; James M. LeBeau; R. Jaramillo

Smooth surfaces and interfaces

Here, we provide additional evidence (in addition to RHEED in Figure 2, and STEM in Figure 3) as to the surface and film-substrate smoothness. In Figure S2, we present the result of the XRR measurement on the films. The presence of well-defined Kiessig interference fringes in the XRR curves indicates that the film surface and the film-substrate interface are smooth in all the samples studied. In Figure S2, we present AFM data measured on the film top surfaces, showing that they are smooth with a r.m.s. roughness between 0.83±0.270.83 \pm0.27 and 2.63±2.342.63 \pm2.34 nm.

Out-of-plane X-ray diffraction

We present in Figure S2 high resolution XRD (HRXRD) data. The out-of-plane scans for all the films show two (202) reflections corresponding to two sets of out-of-plane d-spacings aligning with the LaAlO3\mathrm{LaAlO}_{3} (012) family of reflections. BaZrSe3\mathrm{BaZrSe}_{3} has a larger lattice compared to BaZrS3\mathrm{BaZrS}_{3}, therefore, the (202) reflections shift to smaller Bragg angles, i.e. larger d-spacing, as the Se to S ratio increases. The pair of reflections results from film microstructure, as described in the main text.

Ba-Ba and Zr-Zr spacing maps in the alloy films

We mapped the interatomic cation spacings (averaging both Ba-Ba and Zr-Zr data) in the BaZrS2Se\mathrm{BaZrS}_{2}\mathrm{Se} and BaZrSSe2\mathrm{BaZrSSe}_{2} films. The bottom, template layer that was grown as BaZrS3\mathrm{BaZrS}_{3} shows no significant out-of-plane cation-cation spacing variation. The top layer, where the horizontal antiphase boundary (APB) layers appear, shows a tripartite distribution of spacings for sample y=2y = 2: within, immediately adjacent to, and away from the APBs. The regions away from the APBs produce the most intense peak in the histogram, due to their larger total volume. It is this peak (at 533 pm), together with the central peak in the distribution of data from the bottom layer (at 509 pm), that produce the twin peaks in RSM and HRXRD data (Figure 2, Figure S2). The XRD d-spacing data are indicated by dashed lines for comparison. The distribution for sample y=1y = 1 is similarly broad, suggestive of multiple peaks. It is not as easy to model as the y=2y = 2 case, but it is reasonable to assume that it displays a similar effect of APBs on local structure.

The out-of-plane spacing distributions are broader for the top layers than for the bottom layers, due to the presence of horizontal APBs in the top layers. Similarly, the in-plane spacing distributions are broader for the bottom layers than for the top layers, due to the presence of vertical APBs in the bottom layers.

The presence of APBs and resulting spread in d-spacing complicates a straightforward analysis of the variation in lattice constant measured by XRD with alloy composition. However, in the light of the STEM analysis, we can identify the twin peaks in XRD as representative of regions with high- and low-APB density. In Figure S4, we show that the d-spacing for each of these two populations varies linearly with composition, in accordance with Vegard’s law.

Figure S4. d(101)d_{(101)} spacing determined from fitting the (202) doublets in Figure S2. The orange points indicate the population of larger dd-spacings, corresponding to high-APB density material. The blue points indicate the population of smaller dd-spacings, corresponding to low-APB density material. The dotted lines are linear fits to the y>0y > 0 data, in accordance with Vegard’s law. The black circle at y=0y = 0 represents d(101)d_{(101)} for a low-APB-density BaZrS3_3 film; the grey square indicates data from the literature for a powder pellet of composition y=1.2y = 1.2.[21]

Out-of-plane and in-plane cation–cation distance distributions and top- and bottom-layer maps

Figure 5.

Composition trend in photodetector responsivity

For the epitaxial photodetectors, the absolute responsivity varies strongly with film composition at all wavelengths. Figure S5 shows this responsivity and external quantum efficiency (EQE) trend at 600 nm illumination. The polycrystalline pure sulfide detector shows the lowest responsivity compared to the epitaxial BaZrS3\mathrm{BaZrS}_{3} and all BaZrS(3−y)Sey\mathrm{BaZrS}_{(3-y)}\mathrm{Se}_{y} detectors. The lower responsivity of the polycrystalline BaZrS3\mathrm{BaZrS}_{3} detector is a result of its very different defect concentrations (including a high density of twin boundaries, shown here). The epitaxial BaZrS3\mathrm{BaZrS}_{3} and alloy devices are made from films with total thickness approximately 40 nm, whereas the polycrystalline BaZrS3\mathrm{BaZrS}_{3} device is made from a film 23 nm thick. Although differences in thickness can affect responsivity and EQE, they do not explain the large differences observed here.

Table of samples reported here

The below table records the samples reported here, and their names as appearing in our laboratory notebooks and database.

Sample descriptionDatabase name
polycrystalline BaZrS3\mathrm{BaZrS}_{3}G018
BaZrS3\mathrm{BaZrS}_{3} (y=0y=0)G039
BaZrS(3−y)Sey\mathrm{BaZrS}_{(3-y)}\mathrm{Se}_{y} (y=1y=1)G069
BaZrS(3−y)Sey\mathrm{BaZrS}_{(3-y)}\mathrm{Se}_{y} (y=1.3y=1.3)G066
BaZrS(3−y)Sey\mathrm{BaZrS}_{(3-y)}\mathrm{Se}_{y} (y=2y=2)G065
BaZrS(3−y)Sey\mathrm{BaZrS}_{(3-y)}\mathrm{Se}_{y} (y=3y=3)G060

Table 1.

References

  1. [1]Jaramillo, R. & Ravichandran, J. In praise and in search of highly-polarizable semiconductors: Technological promise and discovery strategies. APL Mater. 7, 100902 (2019).DOI
  2. [2]Brehm, J. A., Bennett, J. W., Schoenberg, M. R., Grinberg, I. & Rappe, A. M. The structural diversity of ABS₃ compounds with d0 electronic configuration for the B-cation. J. Chem. Phys. 140, 224703 (2014).DOI
  3. [3]Sadeghi, I. et al. Making BaZrS₃ Chalcogenide Perovskite Thin Films by Molecular Beam Epitaxy. Adv. Funct. Mater. 31, 2105563 (2021).arxiv.org/abs/2105.10258
  4. [4]Surendran, M. et al. Epitaxial Thin Films of a Chalcogenide Perovskite. Chem. Mater. 33, 7457–7464 (2021).DOI
  5. [5]Niu, S. et al. Thermal stability study of transition metal perovskite sulfides. J. Mater. Res. 33, 4135–4143 (2018).DOI
  6. [6]Sun, Y.-Y., Agiorgousis, M. L., Zhang, P. & Zhang, S. Chalcogenide Perovskites for Photovoltaics. Nano Lett. 15, 581–585 (2015).DOI
  7. [7]Meng, W. et al. Alloying and Defect Control within Chalcogenide Perovskites for Optimized Photovoltaic Application. Chem. Mater. 28, 821–829 (2016).DOI
  8. [8]Ong, M., Guzman, D. M., Campbell, Q., Dabo, I. & Jishi, R. A. BaZrSe₃: Ab initio study of anion substitution for bandgap tuning in a chalcogenide material. J. Appl. Phys. 125, 235702 (2019).DOI
  9. [9]Tranchitella, L. J., Fettinger, J. C., Dorhout, P. K., Van Calcar, P. M. & Eichhorn, B. W. Commensurate Columnar Composite Compounds: Synthesis and Structure of Ba₁₅Zr₁₄Se₄₂ and Sr₂₁Ti₁₉Se₅₇. J. Am. Chem. Soc. 120, 7639–7640 (1998).
  10. [10]Aslanov, L. A. Selenides of the type ABSe₃. Russ. J. Inorg. Chem. 9, 1090–1091 (1964).
  11. [11]Nishigaki, Y. et al. Extraordinary Strong Band-Edge Absorption in Distorted Chalcogenide Perovskites. Sol. RRL 4, 1900555 (2020).
  12. [12]Hanzawa, K., Iimura, S., Hiramatsu, H. & Hosono, H. Material Design of Green-Light-Emitting Semiconductors: Perovskite-Type Sulfide SrHfS₃. J. Am. Chem. Soc. 141, 5343–5349 (2019).
  13. [13]Jing, H.-M. et al. Formation of Ruddlesden–Popper Faults and Their Effect on the Magnetic Properties in Pr₀.₅Sr₀.₅CoO₃ Thin Films. ACS Appl. Mater. Interfaces 10, 1428–1433 (2018).DOI
  14. [14]Bak, J., Bae, H. B., Oh, C., Son, J. & Chung, S.-Y. Effect of Lattice Strain on the Formation of Ruddlesden–Popper Faults in Heteroepitaxial LaNiO₃ for Oxygen Evolution Electrocatalysis. J. Phys. Chem. Lett. 11, 7253–7260 (2020).DOI
  15. [15]Filippone, S. A., Sun, Y.-Y. & Jaramillo, R. The effect of an improved density functional on the thermodynamics and adsorption-controlled growth windows of chalcogenide perovskites. MRS Adv. 3, 3249–3254 (2018).DOI
  16. [16]Aso, R., Kan, D., Shimakawa, Y. & Kurata, H. Atomic level observation of octahedral distortions at the perovskite oxide heterointerface. Sci. Rep. 3, 2214 (2013).DOI
  17. [17]Li, Q. et al. Control of Polaronic Behavior and Carrier Lifetimes via Metal and Anion Alloying in Chalcogenide Perovskites. J. Phys. Chem. Lett. 13, 4955–4962 (2022).DOI
  18. [18]Niu, S. et al. Optimal Bandgap in a 2D Ruddlesden–Popper Perovskite Chalcogenide for Single-Junction Solar Cells. Chem. Mater. 30, 4882–4886 (2018).DOI
  19. [19]Ye, K. et al. Low-energy electronic structure of perovskite and Ruddlesden-Popper semiconductors in the Ba-Zr-S system probed by bond-selective polarized x-ray absorption spectroscopy, infrared reflectivity, and Raman scattering. Phys. Rev. B 105, 195203 (2022).DOI
  20. [20]Ye, K., Zhao, B., Diroll, B. T., Ravichandran, J. & Jaramillo, R. Time-resolved photoluminescence studies of perovskite chalcogenides. Faraday Discuss. 239, 146–159 (2022).
  21. [21]Nishigaki, Y. et al. Extraordinary Strong Band-Edge Absorption in Distorted Chalcogenide Perovskites. Sol. RRL 4, 1900555 (2020).

Paper details

vlnc:W_vmseckq5
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents