betaFeedback

WorksPhysics and Astronomy

A Student Sounding Rocket Experiment to Probe Electron Density in the Lower Ionosphere

Abstract

Earth's ionosphere is primarily generated by the Sun's ionization of atoms in the upper atmosphere. This plasma environment is highly dynamic, exhibits strong spatial and temporal, variations and significantly impacts power systems, navigation, and satellite and ground communications. The University of Delaware Ionospheric Probe (UDIP) was developed as a hands-on learning experience for University of Delaware students on the ionosphere itself and on the development of space technology. Students (mostly undergraduates) have led all aspects of the experiment including mission planning, electronics development, mechanical development, software development, and scientific data analysis. The present study is intended as a guide to readers on how the development of space and near-space flight missions can be successfully incorporated into an undergraduate physics curriculum. The fourth version of the experiment (UDIP-4) flew along with student experiments from across the USA on the 2024 RockSat-C sounding rocket, which was launched from NASA Wallops Flight Facility. During the flight, UDIP-4's Langmuir probe successfully measured the ionosphere's density profile – electron density as a function of altitude – up to an apogee of 114 km. Though the measured density profile agrees well overall with the predictions of theoretical models, UDIP-4 identified a thin layer of enhanced electron density at an altitude of approximately 110 km that is consistent with a sporadic E layer.

Introduction

Earth’s ionosphere is characterized by a substantial fraction of the neutral gas being ionized and extends from approximately 80 to 1000 km in altitude. The ionized gas of the ionosphere absorbs, reflects, and refracts radio waves, which directly impacts many modern technologies: radio communication, navigation (including GPS), and satellite operations. The ionosphere is effectively a transition layer between the terrestrial and space environments – both a part of the Earth’s atmosphere and a region heavily influenced by processes and plasma originating at the Sun. Studying the ionosphere is critical for understanding space weather events that can cause major disruption and damage to power grids, communications systems, and spacecraft[1, 2]. Conditions in the ionosphere vary widely across space and time in very complex ways and has been the object of extensive and ongoing study.[3]

The observation and study of the lower portion of the ionosphere presents a particular challenge. The gas at even the base of the ionosphere is too diffuse for conventional aircraft to achieve lift but also too dense for spacecraft to maintain stable orbits (due to drag). The lower ionosphere can be remotely observed, e.g., via radio waves – a technique that led to the discovery of the ionosphere in the early 20th Century.[4] For in-situ observations, sounding rockets provide the best method for bringing instruments into the lower ionosphere to directly measure its particles and fields.[5] Sounding rockets (also known as suborbital rockets) are medium-sized rockets that launch into space and fall back to Earth without achieving orbit that have a long history of exploring Earth’s near space environment.

RockSat-C[6] is an educational sounding rocket program run annually by NASA Wallops Flight Facility. Each year, teams of students (mostly undergraduate) from across the USA spend the academic year designing and building a wide variety of experiments to fly on a sounding rocket. The program is designed to provide students with access to low-cost flight opportunities, develop their engineering skills, and promote interest in STEM careers[7].

The University of Delaware (UD), in partnership with the Delaware Space Grant Consortium[8], has a long history of participating in RockSat-C. Successive teams of UD students have developed and refined the University of Delaware Ionospheric Probe (UDIP), which features a Langmuir probe for measuring electron density. Langmuir probes, which are among the oldest and most robust plasma instruments, are metal electrodes that measure the electrical properties of a plasma[9, 10]. When a voltage is applied to a Langmuir probe, a response current flows from the probe to the surrounding plasma. Measuring the current for a series of voltages produces an I-V curve, which can be fit with a response function to extract plasma parameters such as the electron density and temperature[11].

This article summarizes the design, operations, and results of the fourth version of the UDIP experiment (UDIP-4), which flew into space on the 2024 RockSat-C sounding rocket and successfully measured electron density as a function of altitude in Earth’s lower ionosphere. It is intended to guide readers on how development of space and near-space flight missions can be successfully incorporated into an undergraduate physics curriculum. Section II describes how the development of UDIP-4 was funded and integrated into a collegiate physics course. Section III overviews the UDIP-4 hardware (both mechanical and electrical) developed by the students. Section IV provides a timeline of the rocket flight. Section V describes the analysis of UDIP-4 data and reports key scientific results. Section VI discusses the program’s benefits to the student participants and comments on the outlook for the UDIP program going forward.

Logistics, Pedagogy, and Funding

The primary objective of RockSat-C is to provide college students with hands-on learning opportunities in space science and engineering. It is structured around the academic year and is designed to be readily integrated into an undergraduate curriculum. Many of the schools that participate in RockSat-C do so annually and have their students complete the program as part of their required senior-design course. A typical student team consists of between four to eight members and works under the guidance of at least one faculty mentor.

The RockSat-C program begins anew each September when each team files an “intent to fly form.” Then, over the course of the fall semester, each team develops and tests their experiment’s design. As part of this process, the students prepare and deliver three virtual presentations to the RockSat-C leadership that mirror those used in NASA’s scientific missions: conceptual design review, preliminary design review, and critical design review. These review presentations help students maintain a steady work schedule and enable them to receive design feedback from the RockSat-C leadership.After the conceptual design review in December, the mission design is finalized, and the team receives notification from RockSat-C as to whether the experiment will be manifested on the rocket. Additional reviews are scheduled through the spring semester and culminate in the visual verification check in early June. In late June, some members of the team then travel with their experiment to NASA Wallops to integrate their experiment into the rocket and observe the launch.

At UD, each new UDIP team is formed in the spring semester before the program starts. To ensure that the team has a balanced set of skills, students are recruited from a variety of physics and engineering majors using email, posters, and announcements in classes. Since student interest typically exceeds team capacity, all students are required to apply and interview for the program. The current year’s UDIP team is heavily involved in recruiting and interviewing the next year’s team. Once the new UDIP team is recruited, its members hold occasional, virtual meetings during the summer to build group cohesion and give students the opportunity to discuss background reading and preliminary designs. Each team member is required to enroll in a “research for credit” course at UD — three credits in the fall semester and three in the spring. This course credit reflects the time commitment (roughly ten hours per week) made by each student and provides a mechanism for ensuring accountability. Student performance is evaluated quarterly and discussed in one-on-one meetings with the instructor.

The UDIP-4 team consisted of twelve undergraduate students, one graduate student, and two mentors (one faculty and one staff). The students were divided among five subteams: science, software, electrical, mechanical, and management.

  • The science subteam defined the mission and instrument requirements (e.g., determined the appropriate measurement cadence and physical dimensions of the Langmuir probes). Prior to flight, these students used existing measurements to generate synthetic data to aid other subteams in their design choices. After flight, they oversaw the analysis of actual flight data.

  • The software subteam led the development of the mission’s two key pieces of software. The flight software ran on the mission’s flight computer and executed and recorded all measurements and operations during flight. The ground software ran on ground computers after flight and processed flight data.

  • The electrical subteam implemented all electrical and electronic components of the mission. These included the science board (containing the electronics for the Langmuir probes), the flight computer, and the power system.

  • The mechanical team oversaw the physical design and implementation of the mission. This included the Langmuir probes themselves, dimensions and placement of all components, and ensuring the entire experiment would survive the harsh conditions of flight (e.g., extreme vibrations, temperature, and drag forces).

  • The management subteam established the mission’s timeline and ensured that all of the subteams were remaining on schedule. These students also oversaw safety and compliance (e.g., ensuring that the experiment would meet all of the requirements for flying on the rocket), tracked the experiment’s inventory, and led preparations for all review presentations with NASA Wallops.

The students selected an overall lead for the mission as well as a lead for each subteam. Each student was required to attend at least two meetings each week: a subteam meeting and a full-team meeting. Students scheduled work sessions and topic-specific meetings as needed. Owing to the size of the team and the complexity of the mission, a strong emphasis was placed on organization and documentation. The two-semester commitment that students made to the project had them participate in UDIP-4 from its conceptual design at the start of the fall semester through to its final fabrication, integration, and testing at the end of the spring semester. The June trip to NASA Wallops (which included the integration and launch of the rocket) was optional but encouraged. After the launch, some students chose to cycle off the project, but many chose to stay to help analyze the UDIP-4 flight data and continue developing the DAPPER CubeSat mission.

The RockSat-C program is closely tied to the National Space Grant College and Fellowship Program[12] (commonly called “Space Grant”), which was established by Congress in 1988 to promote space science education and research. The program supports 52 consortia across the United States: one in each state, the District of Columbia, Puerto Rico, and Guam. Most schools that participate in RockSat-C receive logistical, technical, and/or financial support to do so from their local Space Grant consortium. In 2024, the program fee for a RockSat-C experiment (which included launch expenses) was $9 000 for a half-canister load (such as UDIP) and $15 000 for a full-canister payload. For UDIP, Delaware Space Grant Consortium annually provides the workshop fee, up to $2 000 for supplies, and travel and lodging expenses for the trip to NASA Wallops by the students and mentors.

Photographs of the UDIP-4 Langmuir probes and electronics

Figure 1. Photographs of the UDIP-4 Langmuir probes (top) and electronics (bottom) while undergoing testing prior to integration onto the rocket.

Instrumentation

Figure 1 summarizes the key mechanical and electrical systems of UDIP-4. The UDIP-4 Langmuir probes (Section III A) were mounted to the exterior of the rocket while the stack of electronics boards (Sections III B to III D) was mounted inside the rocket. Though this article offers an overview of the UDIP-4 electronics, circuit diagrams and discussions of the theory of operation of the mission’s custom electronics are provided elsewhere [13].

Langmuir Probes

UDIP-4 carried a pair of identical, cylindrical Langmuir probes each 3.75 in long and 0.32 in in diameter. One probe served as the “ground” probe and was kept at 0 V relative to the rocket’s electrical ground; the other was the “sweep” probe and was swept through a series of DC voltages. The current flowing from the sweep probe, through the surrounding plasma, and to the ground probe was measured for each voltage applied to the sweep probe (Section III B). These measurements of current versus voltage constituted the I-V curves that were UDIP-4’s fundamental data product, which are discussed further in § 2 A.

Special environmental considerations were included in the design of the UDIP-4 Langmuir probes. The 2024 RockSat-C User’s Guide and program welcome documents provide some details on the mechanical environment encountered during flight. The peak spin rate of the payload is typically 5.6 Hz. Sustained accelerations of about 25g are typically encountered during ascent, and designing experiments to withstand impulses of up to 50g is recommended. For drag, the maximum value of ρv2/2\rho v^{2}/2 (where ρ\rho is the density of air around the rocket and vv is the rocket’s speed) is given as about 2.6×1052.6 \times10^{5} Pa. Per the RockSat-C User’s Guide, the full rocket payload (prior to flight) undergoes both sine-wave and random vibrational testing spanning frequencies from 10 to 2000 Hz.

To endure the extreme drag forces of rocket flight, each probe was machined from H13 tool steel, which has a high yield strength. Likewise, the electrical isolation of each probe from the rocket was maintained by a commercially fabricated short tube made from synthetic sapphire. To prevent oxide formation (which would affect electrical performance), the exposed portion of each probe was coated with a colloidal graphite solution (AquaDAG). While Langmuir probes have been used on many different space missions (including sounding rockets), the specific designs vary considerably [14]. Even just within sound-rocket missions, many different sizes, shapes, and electronics have been used for Langmuir probes. Factors like the type of rocket, its specific trajectory, and where/how the probe is mounted on the rocket (e.g., a fixed probe versus a deployable one) all have major impacts on the design. For UDIP-4, the students conducted a literature review to examine past Langmuir probe designs and heavily considered the RockSat-C user guide and past UDIP missions to develop an effective design.

Science Board

The UDIP-4 science board was a student-designed custom printed circuit board (PCB). This board hosted all of the analog and digital electronics required to generate I-V curves from the Langmuir probes (Section III A). A microcontroller on the science board used an external 12-bit digital-to-analog converter (DAC) to sweep through a series of voltages (ranging up to −12-12 to +12+12 V) on the sweep probe. A transimpedance amplifier was used to apply each sweep voltage to the sweep probe and then convert the resultant current to a voltage, which was measured by the microcontroller’s analog-to-digital converters (ADC’s). The microcontroller carried out a voltage sweep on command from the flight computer (Section III C) and sent the resultant I-V curve data to it via a serial communications line.

Flight Computer

The UDIP-4 flight computer, also a student-designed custom PCB, was built around the industrial-rated Arduino Portenta H7 Lite microcontroller. This board also included a nine degree of freedom (9-DoF) module for determining the payload’s motion and orientation (via vector measurements of acceleration, angular velocity, and magnetic field) and an SD card module for recording all flight data. The flight computer was programmed to collect and record data in three successive phases:

  1. Ascent phase (before T+50 seconds). The Langmuir probe system remained powered off, and high-cadence measurements were recorded from the 9-DoF module to characterize the rocket’s launch.

  1. Science phase (T+50 to +400 seconds). Collection of each Langmuir probe I-V curve was alternated with measurements from the 9-DoF module.

  1. Descent phase (T+400 seconds onward). Low-cadence measurements were recorded from the 9-DoF module, and the Langmuir probe system was powered off to prevent any potential electrical short between the probes when the rocket payload landed in the ocean.

Power System

Electrical power for all of UDIP-4’s systems was stored and distributed by the Clyde Space OPTIMUS 30 battery and STARBUCK-NANO electrical power system. Though these components provided far more power storage and command options than needed for UDIP-4, using them provided valuable experience (for students and mentors alike) for the development of future projects (Section VI).

Rocket Flight

UDIP-4 was launched on RockSat-C’s Terrier-Improved Orion sounding rocket from NASA’s Wallops Flight Facility (37° 50′ 21″ N, 75° 28′ 54″ W) on Thursday, June 20, 2024 at 05:30 EDT (09:30 UTC). The rocket followed a nearly vertical trajectory and remained illuminated by dawn sunlight throughout its flight. Figure 2 shows the rocket’s altitude

Flight profile showing altitude and acceleration versus time after launch

Figure 2. Top: Altitude vs time after launch. Bottom: Acceleration vector vs time after launch. The darker shaded gray region indicates the Terrier 1st stage burn, while the lighter shade is the Orion 2nd stage burn. The blue vertical line denotes the beginning of UDIP-4’s Science data. The green vertical line indicates the time of apogee of the sounding rocket.

and vector acceleration as functions of time after launch. Altitude measurements were derived from radar tracking data from NASA Wallops Flight Facility. Acceleration measurements (a=axx^+ayy^+azz^\mathbf{a} = a_x\hat{\mathbf{x}} + a_y\hat{\mathbf{y}} + a_z\hat{\mathbf{z}}) were recorded from UDIP-4’s 9-DoF module (Section III C). This module was mounted in the rocket’s non-inertial reference frame with its zz-axis oriented nose-ward along the rocket’s axis.

At T+0 seconds, liftoff occurred with the ignition of the rocket’s Terrier motor. This first stage burned for approximately 5 seconds, during which the peak upward acceleration was az=235a_z = 235 m/s2^2 = 24gg. From T+5 to +15 seconds, the rocket decelerated and slightly deviated (i.e., az<0a_z < 0) due to drag. At about T+15 seconds, the Improved Orion motor in the rocket’s second stage ignited and then burned for about 25 seconds. To provide the rocket with “spin stabilization,” the rocket was spun about its axis during this period, which is evidenced by an increase in centrifugal acceleration, ax2+ay2\sqrt{a_x^2 + a_y^2}.

After T+40 seconds, the rocket followed a ballistic trajectory. It achieved apogee at approximately T+170 seconds at an altitude of 114 km. The rocket payload deployed its parachute during its descent, splashed down into the Atlantic Ocean, recovered and returned to Wallops Flight Facility later the same day.

The UDIP-4 electronics, which had been activated at approximately T-57 seconds, continued collecting data from the 9-DoF module until the recovered experiment was deactivated. As noted in Section III C, the UDIP-4 flight computer was programmed to only collect Langmuir probe data between T+50 and T+400 seconds, when the rocket was expected to be at its highest altitudes.

Results

This section summarizes the scientific results from the UDIP-4 flight and includes samples flight data, a description of data processing, and the final flight results.

I-V Curve

Figure 3 shows an example I-V curve collected by UDIP-4 shortly after reaching apogee. To generate this curve, the science board (Section III B) swept the probe voltage, VV, from about −6-6 to about +6+6 V in equally spaced steps. For each voltage step, the science board measured the current, II, that flowed through the plasma. The measured (I−VI-V) data appear in Figure 3 as cyan dots. The floating potential (VfV_f; the voltage for which the smoothed I=0I = 0) and the plasma potential (VpV_p; voltage at maximum dIdV\frac{dI}{dV}) are indicated with blue and green vertical lines, respectively.

The data with V>VpV > V_p are in the “electron saturation region” and are characterized by currents that arise almost entirely from electron motion. The response function in this region is[11, 15, 16]:

I=eneAkBTe2πme[1+e(V−Vp)kBTe]m(1)I = e n_e A \sqrt{\frac{k_B T_e}{2\pi m_e}}\left[1+\frac{e(V-V_p)}{k_B T_e}\right]^m \tag*{(1)}

where m=1/2m = 1/2 for a long, thin cylindrical probe, but m=1m = 1 for a spherical probe.

Fitting for Electon Density

An estimate of the electron density, nen_e, can be extracted from each I-V curve for UDIP-4 data using a non-linear fitting algorithm to fit (1) to the points from the electron saturation region (V>VpV > V_p). Each I-V curve’s VpV_p-value was identified by smoothing the data and then determining the voltage for which the current gradient was highest. Figure 3 shows the best-fit curve for the example I-V curve in red.

I-V curve measured by UDIP-4

Figure 3. (Color online) I-V curve (i.e., plot of current versus probe voltage) measured by UDIP-4 at T+223.41 seconds. Data are shown as cyan points, and vertical lines indicate the floating potential (VfV_f, blue) and plasma potential (VpV_p, green). The best-fit curve of the data from the electron saturation (V>VpV > V_p) is plotted in red. See § 2 A and V B for full definitions and analysis.

In initial fits of the I-V curves, TeT_e was allowed to vary as a free parameter along with nen_e, but the fitting algorithm consistently returned uncertainties in TeT_e that were multiple orders of magnitude larger than the best-fit values in TeT_e. The problem in reliably extracting electron temperature measurements from Langmuir probe data is a common one in the lower ionosphere[17, 18], where the gas’s ionization fraction remains relatively low. Consequently, a fixed value of Te=500T_e = 500 K was chosen for all fits based on theoretical predictions[19] and measurements from other missions[16].

Conversely, the exponent mm in Equation 1 was allowed to vary as a free parameter in each I-V curve fit. The value of m=1/2m = 1/2 assumes that the probe is a long, thin cylinder, and the UDIP-4 probes were made shorter and thicker than ideal to survive intense drag forces during launch (Section III A). Even so, for most I-V curves, the best-fit mm-value was closer to m=1/2m = 1/2 than to m=1m = 1 (the value for a spherical probe).

Electron Density Profile

Figure 4 shows the trend in UDIP-4 measurements of nen_e versus altitude for both the rocket’s ascent and descent. Data from altitudes less than 90 km are omitted since the electron density was generally too low for UDIP-4 to reliably measure. A smoothed version of the UDIP-4 data (produced with a ten-point smoothing window) is plotted in red. The error bars indicate the uncertainties in density returned by the fitting algorithm and do not include any additional error resulting from the choice of a fixed electron temperature (§ 2 B).

The un-smoothed data show a quasi-periodicity that mostly likely is the result of the rocket’s spin. As the rocket rotated, the Langmuir probe passed in and out of sunlight, which caused the number of photoelectrons produced around it to vary widely. This interpretation is supported by a Lomb-Scargle periodogram[20] that was produced from the time series of nen_e measurements and that showed a strong peak at 5.4 Hz. This frequency corresponds well with the rocket’s average measured spin rate. Though the complex effects of sunlight on Langmuir probes certainly affect the absolute calibration of UDIP-4 density measurements, the relative changes in nen_e values are likely robust.

The orange curve in Figure 4 shows the theoretical electron density profile predicted by the International Reference Ionosphere (IRI 2020) model[19] for the date, time, and location of the rocket launch. Overall, the IRI values agrees well with the observed values except for a relatively narrow layer of enhanced electron density that UDIP-4 observed both on its ascent and descent at an altitude of roughly 110 km. This feature is consistent with a sporadic E layer (Es)[21, 22, 23, 24]. UDIP-4 observed the altitude and thickness of the layer to be slightly different on the ascent and descent. The peak density occurred on the ascent at an altitude of about 111 km but at 108 km on the descent. Likewise, the thickness (full-width at half-maximum) of the layer was about 4 km on the ascent and 2.5 km on the descent. Most likely, these differences are mostly due more to spatial inhomogeneities than to temporal changes since UDIP-4’s two passages through the layer were separated by 13 km in horizontal distance but only 62 s in time.

The most widely accepted and supported theory for the ES_{\mathrm{S}} layer is the wind shear theory, resulting from vertical electric field induced motion occurring from shear layers in the ionospheric plasma[25, 26, 27]. The shear is developed through an enhancement in neutral density at roughly 125 km altitude, which tends to carry metallic ions with the zonal neutral motion[24] and thus forces ions into a thin dense sheet. In previous sounding-rocket missions launched from Wallops Island, these layers were found to occur between 100 and 110 km with a density enhancement between roughly 3 and 6 times the background measurements[28]. Additionally, UDIP-4 displayed a convergence in both electron density and altitude of the ES_{\mathrm{S}} layer with a rocket that was launched at a similar time in a series of night-time sounding rockets also launched from Wallops Island[29]. While UDIP-4 did not have a secondary measurement device for confirmation of the ES_{\mathrm{S}} layer, the previous literature agrees well with our measurements. This indicates that the electron density was measured correctly, and that the deviations from the IRI are in fact a physical phenomenon in the ionosphere.

Conclusions and Future Work

Designing UDIP-4 and analyzing its data provided students with real-life experience in all the essential areas of an undergraduate physics curriculum: mechanics (ballistics and drag), electromagnetism, thermodynamics, quantum mechanics (photoelectric effect), electronics, and data analysis. The UDIP-4 students also gained skills in collaboration, documentation, team organization, and time management, all of which are essential for any flight mission. Already, some of the UDIP-4 students have graduated and gone onto graduate schools and careers in academia and industry.

UDIP-4 also served a critical role as the test flight of the Delaware Atmospheric Plasma Probe Experiment (DAPPEr). This ambitious, student-led CubeSat mission is slated to deploy into orbit from the International Space Station in 2027 and become Delaware’s first orbital spacecraft. Like UDIP-4, DAPPEr will carry a pair of Langmuir probes, but it will use them to explore the upper ionosphere instead. DAPPEr is drawing on substantial heritage from UDIP-4 – most notably its power system, flight computer, and science board. Additionally, many UDIP-4 students have continued to work on DAPPEr, bringing them essential technical and management experiences.

Acknowledgments

The authors extend their deepest thanks to Christopher Koehler, Joyce L. Winterton, and everyone associated with the RockSat-C program and NASA Wallops Flight Facility for all their assistance in developing, integrating, launching, and recovering the UDIP-4 experiment. Special thanks also go to Angela Miller (Delaware Space Grant Consortium) for logistical support and Derrick Allen (University of Delaware) for machining services. The authors gratefully acknowledge the help of Michael Wiltberger (University Corporation for Atmospheric Research; UCAR) in interpreting Figure 4. Financial support for UDIP-4 was provided by the Delaware Space Grant Consortium (DESGC) under NASA Award 80NSSC20M0045. Laboratory space and equipment were provided by the Delaware Space Observation Center (DsPOC), which is supported by NASA Awards 80NSSC22K0884 and 80NSSC23K0608.

Electron number density as a function of altitude for the rocket's ascent and descent

Figure 4. (Color online) Electron number density, nen_e, as a function of altitude for both the rocket’s ascent (bottom) and descent (top). Values for nen_e (including error bars) from the UDIP-4 I-V curves are shown in dark blue. The red curve shows a ten-point rolling average of these data, and orange curve shows the predictions of the IRI model[19] for comparison.

Author Contributions

Data analysis and drafting of this article was lead by the mission’s student science team, which included authors JG, JB, CPB, and AS. Mentorship to the students was provided by authors JD, DS, JWB, WHM, and BAM. All other authors were students who contributed to the mission’s hardware and/or software development.

References

  1. [1]Committee on the Societal and Economic Impacts of Severe Space Weather Events, “Severe space weather events – understanding societal and economic impacts: A workshop report,” Tech. Rep. (National Research Council, Washington, DC, 2008).
  2. [2]Abt Associates, “Social and economic impacts of space weather in the united states,” Tech. Rep. (NOAA National Weather Service, Bethesda, MD, 2017).
  3. [3]M. C. Kelley, The Earth’s ionosphere: Plasma physics and electrodynamics, Vol. 96 (Academic press, 2009).
  4. [4]C. T. Russell, J. G. Luhmann, and R. J. Strangeway, Space physics: An introduction (Cambridge University Press, 2016).
  5. [5]S. Christe, B. Zeiger, R. Pfaff, and M. Garcia, “Introduction to the Special Issue on Sounding Rockets and Instrumentation,” Journal of Astronomical Instrumentation 05, 1602001 (2016).arxiv.org/abs/1602.02333
  6. [6]Https://www.nasa.gov/wallops/stem/rocksat.
  7. [7]T. Koehler, S. Carroll, and E. Logan, “Rockon and rocksat: A nasa and cosgc collaboration to train tomorrow’s engineers,” (2011).
  8. [8]Https://www.delspace.org/.
  9. [9]H. M. Mott-Smith and I. Langmuir, “The Theory of Collectors in Gaseous Discharges,” Physical Review 28, 727–763 (1926).
  10. [10]J. E. Allen, “Probe theory - the orbital motion approach,” Physica Scripta 45, 497–503 (1992).DOI
  11. [11]F. F. Chen, “Langmuir probe analysis for high density plasmas,” Physics of Plasmas 8, 3029–3041 (2001).DOI
  12. [12]Https://spacegrant.org/.
  13. [13]R. Khan, The Delaware Atmospheric Plasma Probe Experiment: The Flight Computer and Science Instrument Subsystem, Master’s thesis, University of Delaware (2025).
  14. [14]T. Abe and K.-i. Oyama, “Langmuir probe,” in An Introduction to Space Instrumentation, edited by K. Oyama and C. Z. Cheng (TERRAPUB, 2013) pp. 63–75.DOI
  15. [15]E. V. Shun’ko, Langmuir Probe in Theory and Practice (Universal Publ, Boca Raton, Fla, 2008).
  16. [16]K. Oyama and C.-Z. Cheng, An Introduction to Space Instrumentation (Terrapub, 2013).
  17. [17]K. Hirao and K. Oyama, “A Critical Study on the Reliability of Electron Temperature Measurements with a Langmuir Probe,” Journal of geomagnetism and geoelectricity 24, 415–427 (1972).DOI
  18. [18]D. L. Rudakov, J. A. Boedo, R. A. Moyer, P. C. Stangeby, A. McLean, and J. G. Watkins, “Effect of electron temperature fluctuations on slowly swept Langmuir probe measurements,” Review of Scientific Instruments 75, 4334–4337 (2004).DOI
  19. [19]D. Bilitza, M. Pezzopane, V. Truhlik, D. Altadill, B. W. Reinisch, and A. Pignalberi, “The International Reference Ionosphere Model: A Review and Description of an Ionospheric Benchmark,” Reviews of Geophysics 60 (2022), 10.1029/2022rg000792.DOI
  20. [20]J. T. VanderPlas, “Understanding the Lomb–Scargle Periodogram,” The Astrophysical Journal Supplement Series 236, 16 (2018).DOI
  21. [21]C. Haldoupis, “Midlatitude Sporadic E. A Typical Paradigm of Atmosphere-Ionosphere Coupling,” Space Science Reviews 168, 441–461 (2012).
  22. [22]B. Yu, X. Xue, X. Yue, C. Yang, C. Yu, X. Dou, B. Ning, and L. Hu, “The global climatology of the intensity of the ionospheric sporadic E layer,” Atmospheric Chemistry and Physics 19, 4139–4151 (2019).DOI
  23. [23]K.-I. Oyama, T. Abe, H. Mori, and J. Y. Liu, “Electron temperature in nighttime sporadic E layer at mid-latitude,” Annales Geophysicae 26, 533–541 (2008).DOI
  24. [24]J. D. Mathews, “Sporadic E: Current views and recent progress,” Journal of Atmospheric and Solar-Terrestrial Physics 60, 413–435 (1998).DOI
  25. [25]J. D. Whitehead, “Production and prediction of sporadic E,” Reviews of Geophysics 8, 65–144 (1970).DOI
  26. [26]J. D. Whitehead, “Recent work on mid-latitude and equatorial sporadic-E,” Journal of Atmospheric and Terrestrial Physics 51, 401–424 (1989).DOI
  27. [27]D. Layzer, “Theory of Midlatitude Sporadic E,” Radio Science 7, 385–395 (1972).DOI
  28. [28]L. G. Smith and E. A. Mechtly, “Rocket Observations of Sporadic-E Layers,” Radio Science 7, 367–376 (1972).DOI
  29. [29]L. G. Smith, “A sequence of rocket observations of night-time sporadic-E,” Journal of Atmospheric and Terrestrial Physics 32, 1247–1257 (1970).DOI

Paper details

vlnc:W_vp23939u
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents