betaFeedback

WorksPhysics and Astronomy

Simulation of the 4H-SiC Low Gain Avalanche Diode

Abstract

Silicon Carbide device (4H-SiC) has potential radiation hardness, high saturated carrier velocity and low temperature sensitivity theoretically. The Silicon Low Gain Avalanche Diode (LGAD) has been verified to have excellent time performance. Therefore, the 4H-SiC LGAD is introduced in this work for application to detect the Minimum Ionization Particles (MIPs). We provide guidance to determine the thickness and doping level of the gain layer after an analytical analysis. The gain layer thickness dgain=0.5 μmd_{gain}=0.5~μm is adopted in our design. We design two different types of 4H-SiC LGAD which have two types electric field, and the corresponding leakage current, capacitance and gain are simulated by TCAD tools. Through analysis of the simulation results, the advantages and disadvantages are discussed for two types of 4H-SiC LGAD.

Introduction

Searching for high radiation hardness and robustness 4D (time and space) detectors apply to future particle colliders and nuclear reactors where the irradiation flux >2×1016neq/cm2> 2 \times10^{16} n_{\mathrm{eq}}/\mathrm{cm}^{2} is [1] one of the main challenges during the last decade. As the wide band-gap semiconductor material, Silicon Carbide (SiC) is an ideal material to fabricate radiation-resistant devices. Benefited the fast development of the industrial investment of SiC power electronic devices, such as the technology of SiC substrate and fabricating process, design and fabricating the SiC devices to apply in high irradiation flux and high temperature environment become possible. In the major SiC polytypes (3C-SiC, 4H-SiC, 6H-SiC), because the 4H-SiC has the highest band-gap (3.26 eV) corresponding to the highest potential radiation hardness, it is more concerned in the study of high radiation hardness devices.

As the one of significant dimensions for the 4D detectors, time performance strongly depends on carrier velocity and signal noise ratio (S/N) [2]. The Silicon Low Gain Avalanche Diode (LGAD) has been verified that has better than 50 ps time resolution due to its good S/N between the low gain range (10~100). And also it has been developed successfully by the various foundries in the past few years [3, 4, 5, 6, 7, 8, 9, 10, 11]. However, present studies indicate the collected charges of Silicon LGAD decrease rapidly when the irradiation flux up to 2.5×1015neq/cm22.5 \times10^{15} n_{\mathrm{eq}}/\mathrm{cm}^{2}. Besides, the Silicon LGAD needs cooling to -30 °C to offset the rapidly rising of leakage current in the extreme irradiation environment [11, 12, 13]. Compared with Silicon, 4H-SiC has higher atomic displacement energy, higher saturated velocity and stability in high temperatures. Furthermore, the average e-h pairs generation when Minimum Ionization Particles (MIP) pass through 1 μ\mum 4H-SiC material is 55 pairs/μpairs/\mum [14], which the signal is satisfied with the most of electronics if consider a 50 μ\mum 4H-SiC LGAD with 10 gain.

Previous measurements have indicated the 100 ps time resolution could be achieved by 100 μ\mum 4H-SiC PIN for detection of MIPs [15]. The corresponding simulation of 3D 4H-SiC detector indicates the time resolution could reach to 25 ps and shows good stability on high temperature [16]. So it has great interest to design a 4H-SiC LGAD for the application of fast particle detection.

Therefore, this work gives a study of 4H-SiC LGAD by simulation. In Sec. 2, the thickness and doping level of the gain layer are discussed after analytical analysis. Based on the results in analytical analysis, we design two types of 4H-SiC LGAD and discuss the simulation results of leakage current, capacitance and gain in § 3. Finally, the results are summarized in § 4.

4H-SiC LGAD Design

To detect the MIPs, the impact ionization coefficient and the generated e-h pairs of 4H-SiC material are essential factors that should be considered in the design of 4H-SiC LGAD. Consider a typical (P++)-(N+)-(N-)-(N++) 4H-SiC LGAD structure, where the P++ layer is the anode, N+ layer is the gain layer with high electric field, N- layer is the bulk layer which the thickness dominates the initial e-h pairs generation, and N++ is cathode layer. We provide some basic policies of 4H-SiC LGAD below after analytical analysis.

The thickness and electric field level of the gain layer is determined depending on the impact ionization coefficient. Figure 1 lists the impact ionization coefficients of Si and 4H-SiC from different models. Based on previous study of P-type Si-LGAD, the electric field is between 2×105∼3×1052 \times10^{5} \sim3 \times10^{5} V/cm for the thickness of gain layer ∼ 1 µm[20]. Similarly, in terms of the gain layer with the thickness of 0.1 ∼ 1.0 µm, the impact ionization coefficient of the low gain region ranges from 103 cm−1∼105 cm−110^{3}\ \mathrm{cm}^{-1} \sim10^{5}\ \mathrm{cm}^{-1}, as highlighted in the yellow band of Figure 1, the electric field is about 1×106∼4×1061 \times10^{6} \sim4 \times10^{6} V/cm for the 4H-SiC LGAD. To acquire the higher gain/E ratio, the N-type 4H-SiC LGAD is adopted in our work where the impact ionization of initial holes dominates the carrier multiplication.

Image not extracted

Figure 1. Impact ionization coefficient of Si and 4H-SiC at T = 300 K. The gray lines of Si are from van Overstraeten–de Man model[17], and cyan lines of Si are from Massey model[18]. They are validated by LGAD simulation in previous studies[19] [20]. The balck lines of 4H-SiC are from Loh model[21] which could predicate the breakdown characterization of 4H-SiC accurately in the electric field from 0.9 to 5 MV/cm. The blue lines are from Hatakeyama model on < 0001 > direction of 4H-SiC which is based on measurement[22]. The possible low gain region for 0.1 ∼ 1.0 µm gain layer is marked by the yellow band.

To acquire enough initial e-h pairs, the thickness of the bulk layer should be considered in design of 4H-SiC LGAD. In our design, a 50 µm bulk layer is decided which would be ionized ∼ 2500 initial e-h pairs by MIP. After the multiplication of carries with gain∼ 10, the collected charges is about 4 fC. However, to utilize the total 50 µm bulk layer, it should be depleted under an appropriate low voltage. So it demands the doping level of the bulk layer as low as possible. The high quality, low doping and thick 4H-SiC epitaxy are the main challenges of 4H-SiC LGAD. Fortunately, depending on our previous study, the high quality 100 µm 4H-SiC epitaxy layer with the doping level <1×1014 cm−3< 1 \times10^{14}\ \mathrm{cm}^{-3} has been achieved successfully in the PIN device to detect MIPs. Conservatively, the doping level of the bulk layer is determined to 1×1014 cm−31 \times10^{14}\ \mathrm{cm}^{-3} in the 4H-SiC LGAD design.

One of the significant operating conditions of LGAD is

VFD<U<VBD(1)V_{FD} < U < V_{BD} \tag*{(1)}

where UU is operating voltage, VFDV_{FD} is full depletion voltage and VBDV_{BD} is breakdown voltage. And the device should have an appropriate gain between VFDV_{FD} and VBDV_{BD}. In our design, we demand the gain ∼ 10 at U=500U = 500V and VFD<12VBDV_{FD} < \frac{1}{2}V_{BD} to guarantee the operating voltage range could be applied by the present source meter like Keithley 2410. Under those limitations, the thickness and doping level of 4H-SiC LGAD could be deduced analytically. The VFDV_{FD} is calculated by

VFD=VGL+VBULK=q×Ngaineff×dgain2+Nbulkeff×dbulk22εSiCε0(2)V_{FD}=V_{GL}+V_{BULK}=\frac{q\times N^{eff}_{gain}\times d^{2}_{gain}+N^{eff}_{bulk}\times d^{2}_{bulk}}{2\varepsilon_{SiC}\varepsilon_{0}} \tag*{(2)}

where qq is unit charge; VGLV_{GL} and VBULKV_{BULK} are depletion voltage of gain layer and bulk layer; NgaineffN^{eff}_{gain} and NbulkeffN^{eff}_{bulk} are doping level; dgaind_{gain} and dbulkd_{bulk} are thickness of corresponding layer. The VBULKV_{BULK} is estimated ∼230\sim230 V if consider dbulk=50 μmd_{bulk}=50\ \mu\mathrm{m} and Nbulkeff=1×1014 cm−3N^{eff}_{bulk}=1\times10^{14}\ \mathrm{cm}^{-3} that mentioned before. Then the average electric field in gain layer Eˉgain\bar{E}_{gain} could be deduced:

Eˉgain=U×q×Ngaineff×dgain2q×Ngaineff×dgain2+q×Nbulkeff×dbulk2×1dgain(3)\bar{E}_{gain}=U\times\frac{q\times N^{eff}_{gain}\times d^{2}_{gain}}{q\times N^{eff}_{gain}\times d^{2}_{gain}+q\times N^{eff}_{bulk}\times d^{2}_{bulk}}\times\frac{1}{d_{gain}} \tag*{(3)}

Consider the average electric field in gain layer is Eˉgain\bar{E}_{gain}, the impact ionization coefficient of electron αn\alpha_{n} and hole αp\alpha_{p} could be calculated by different model. In our work, the Hatakeyama model[22] is applied because the anisotropy is considered. So the number of e-h pairs M(x)M(x) created by a single of initial e-h pair at position xx in the depleted gain layer is[23]

M(x)=exp⁡[∫0x(αn−αp) dx]1−∫0dgainαpexp⁡[∫0x(αn−αp) dx] dx(4)M(x)=\frac{\exp\left[\int_{0}^{x}(\alpha_{n}-\alpha_{p})\,dx\right]}{1-\int_{0}^{d_{gain}}\alpha_{p}\exp\left[\int_{0}^{x}(\alpha_{n}-\alpha_{p})\,dx\right]\,dx} \tag*{(4)}

The breakdown condition is assumed to ∫0dgainαp=1\int_{0}^{d_{gain}}\alpha_{p}=1 in N-type 4H-SiC LGAD. Consequently, the relation between NgaineffN^{eff}_{gain} and dgaind_{gain} can be determined which shows in Figure 2 depends on Eq. (1)-(4) and other limitations mentioned in our design. The results in Figure 2 indicate the theoretical NgaineffN^{eff}_{gain} and dgaind_{gain} values should be located in “allowed region” between the black line (Gain=1) and red line (Gain=∞\infty). Some important information could be extracted in Figure 2 to guid the design of 4H-SiC LGAD: (1) The dgaind_{gain} could not be larger than 1.2 μm\mu\mathrm{m} otherwise the device will be premature breakdown before full depletion; (2) In general, NgaineffN^{eff}_{gain} decreases with the thickness of dgaind_{gain}. When dgaind_{gain} is less than 0.5 μm\mu\mathrm{m}, NgaineffN^{eff}_{gain} decreases rapidly by nearly one order of magnitude with the increase of dgaind_{gain} and gradually flattens when dgaind_{gain} is greater than 0.5um. Therefore, the dgain<0.5 μmd_{gain}<0.5\ \mu\mathrm{m} is not suggested due to high sensitive between the dgaind_{gain} and NgaineffN^{eff}_{gain}; (3) 1.0 μm\mu\mathrm{m} thickness is reasonable but easily premature breakdown caused by the fluctuation of NgaineffN^{eff}_{gain} and dgaind_{gain} in practical process. For a comprehensive consideration, the 0.5 μm\mu\mathrm{m} thickness of gain layer dgaind_{gain} is adopted in this work where the doping level NgaineffN^{eff}_{gain} between 2×1017 cm−3∼4×1017 cm−32\times10^{17}\ \mathrm{cm}^{-3}\sim4\times10^{17}\ \mathrm{cm}^{-3}.

Image not extracted

Figure 2. The relation of NgaineffN_{\mathrm{gain}}^{\mathrm{eff}} and dgaind_{\mathrm{gain}} for the (P++)-(N+)-(N-)-(N++) 4H-SiC LGAD structure which has 50 µm N- bulk layer with 1×1014 cm−31 \times10^{14}\ \mathrm{cm}^{-3} doping level when U = 500 V. The black line is Gain=1 and red line is Gain=∞ (breakdown). The numbers on the background are the full depletion voltages (VFDeffV_{\mathrm{FD}}^{\mathrm{eff}}, dgaind_{\mathrm{gain}}). The green region is “allowed region” which is satisfied with VFD<VBDV_{\mathrm{FD}} < V_{BD}.

Simulation

To verify the results by analytical analysis in § 2 and determine the specific doping level of gain layer NgaineffN^{eff}_{gain}, we simulate the characteristics of 4H-SiC LGAD with the help of TCAD (Technology Computer Aided Design) tools.

Configuration of physical parameters

In our simulation, the dielectric constant of 4H-SiC material is εSiC=9.7\varepsilon_{SiC}=9.7. The electron & hole effective mass and conduction band density-of-state models are from [24]. The parameters of the carrier mobility model with doping-dependence refer to [25, 26]. The impact ionization model uses Hatakeyama model [22]. The MIPs is simulated by heavy ion model of TCAD [27]. Finally, the wafer system of 4H-SiC has a 4° miscut angle in all simulations.

Structure

Depends on the analytical analysis in § 2, a 2D 4H-SiC LGAD structure is designed (see Figure 3(a)) which has five 4H-SiC layers listed below:

Image not extracted

Figure 3. Longitudinal layers design of the 4H-SiC LGAD studied in this work: (a) “Triangle” type with illustration of P+ type ohmic contact layer, N+ gain layer, N- bulk layer, N type buff layer and N++ substrate. (b) “Trapezoid” type: with illustration of P+ type ohmic contact layer, N gain layer, N+ electric field control layer, N- bulk layer, N type buff layer and N++ substrate.

  • P++ : contact layer, 0.3 μm\mu\mathrm{m}, 1×1019 cm−31\times10^{19}\ \mathrm{cm}^{-3}.

  • N+ : gain layer, the thickness dgaind_{gain} and doping level NgaineffN^{eff}_{gain} are studied in this work.

  • N- : bulk layer, 50 μm\mu\mathrm{m}, 1×1014 cm−31\times10^{14}\ \mathrm{cm}^{-3}.

  • N buff : buff layer, 5.0 μm\mu\mathrm{m}, 1×1018 cm−31\times10^{18}\ \mathrm{cm}^{-3}.

  • N++ : substrate layer, 10 μm\mu\mathrm{m}, 1×1020 cm−31\times10^{20}\ \mathrm{cm}^{-3}.

The width of the structure is 10 μm\mu\mathrm{m} which is satisfied with 2D heavy ion simulation. Because of the “triangle” electric field between P++ layer and N+ layer, we address the structure like Figure 3(a) as Triangle-Type 4H-SiC LGAD. For comparative study, the same structure of 50 μm\mu\mathrm{m} 4H-SiC PIN is designed and the N+ gain layer is removed.

For the same reason, another structure shows in Figure 3(b) is addressed as Trapezoid-Type 4H-SiC LGAD due to the “trapezoid” electric field that will be discussed in § 3.4.

Simulated II-VV and 1/C21/C^2-VV

To determine the breakdown voltage VBDV_{BD} for the Triangle-Type 4H-SiC LGAD, the II-VV curves are simulated which is shown in Figure 4. As Figure 4(a)∼Figure 4(c) show, for different gain layer doping levels, the breakdown voltages could be restrained in 500 V∼1000 V in our designs. Under this condition, the order of magnitude of NgaineffN^{eff}_{gain} is 1018 cm−310^{18}\ \mathrm{cm}^{-3} when dgain=0.1 μmd_{gain}=0.1\ \mu\mathrm{m} and 1017 cm−310^{17}\ \mathrm{cm}^{-3} when dgain=1.0 μmd_{gain}=1.0\ \mu\mathrm{m}. It agrees with the predication of analytical analysis in Figure 2. Compare with the fluctuation interval of NgaineffN^{eff}_{gain} related with VBDV_{BD} between 500 V∼1000 V, the declining rate of VBDV_{BD} is ∼ 100V / (1016 cm−310^{16}\ \mathrm{cm}^{-3}) for dgain=0.1 μmd_{gain}=0.1\ \mu\mathrm{m}, but increases to ∼ 100V / (1015 cm−310^{15}\ \mathrm{cm}^{-3}) for dgain=1.0 μmd_{gain}=1.0\ \mu\mathrm{m}. It also agrees with the analysis in § 2 where the relevance is stronger between NgaineffN^{eff}_{gain} and dgaind_{gain} for thinner dgaind_{gain}. It should be noted that the leakage current of 4H-SiC LGAD at low voltages is smaller than PIN is caused by very small volume of depleted region when U<VGLU<V_{GL}. However, the leakage current of all 4H-SiC LGAD designs are larger than PIN after full depletion. The gain of leakage current is ∼ 10 times indicates the low gain is achieved.

Image not extracted

Figure 4. Leakage current for simulation at 4 different gain layer doping levels of Triangle-Type 4H-SiC LGAD and PIN: (a) dgain=0.1 μmd_{\mathrm{gain}} = 0.1\ \mu\mathrm{m}; (b) dgain=0.5 μmd_{\mathrm{gain}} = 0.5\ \mu\mathrm{m}; (c) dgain=1.0 μmd_{\mathrm{gain}} = 1.0\ \mu\mathrm{m}. The colored lines are Triangle-Type 4H-SiC LGAD. The dotted gray line is PIN.

To determine the gain layer depletion voltage VGLV_{GL} and full depletion voltage VFDV_{FD} for the Triangle-Type 4H-SiC LGAD, the 1/C21/C^2-VV curves are simulated which is shown in Figure 5. As Figure 5(a)∼Figure 5(c) show, the influence for fluctuation of NgaineffN^{eff}_{gain} to VGLV_{GL} could be neglected. For different gain layer doping levels, the VFDV_{FD} of all 4H-SiC LGAD designs are smaller than 500 V that is satisfied with our demand referred in § 3.4. Compare with the fluctuation interval of NgaineffN^{eff}_{gain} related with VGLV_{GL} for different dgaind_{gain}, the VGLV_{GL} increases rapidly from ∼140 V for dgain=0.1 μmd_{gain}=0.1\ \mu\mathrm{m} to ∼140 V for dgain=1.0 μmd_{gain}=1.0\ \mu\mathrm{m}, although the NgaineffN^{eff}_{gain} has already decreased one order of magnitude. It indicates the thickness of gain layer is leading factor of VGLV_{GL} in 4H-SiC LGAD.

Image not extracted

Figure 5. 1/C21/C^2-VV for simulation at 4 different gain layer doping levels of Triangle-Type 4H-SiC LGAD and PIN: (a) dgain=0.1 μmd_{\mathrm{gain}} = 0.1\ \mu\mathrm{m}; (b) dgain=0.5 μmd_{\mathrm{gain}} = 0.5\ \mu\mathrm{m}; (c) dgain=1.0 μmd_{\mathrm{gain}} = 1.0\ \mu\mathrm{m}. The colored lines are Triangle-Type 4H-SiC LGAD. The dotted gray line is PIN.

Study of gain layer design

To control the electric field near the gain layer handily, another 4H-SiC LGAD structure is introduced which has an “trapezoid” electric field (See Figure 3(b)). As mentioned in § 3.2, we address it as Trapezoid-Type 4H-SiC LGAD. Different with the Triangle-Type 4H-SiC LGAD has five layers, the Trapezoid-Type has six layers where another N+ layer called the electric field control layer which is inserted into the interface between the N gain layer and N- bulk layer. The profiles of each layer are listed below:

  • P++ : contact layer, 0.3 μm\mu\mathrm{m}, 1×1019 cm−31\times10^{19}\ \mathrm{cm}^{-3}.

  • N : gain layer, 1×1016 cm−31\times10^{16}\ \mathrm{cm}^{-3}. The thickness dgaind_{gain} is studied in this work.

  • N+ : electric field control layer, 0.1 μm\mu\mathrm{m}. The doping level NeceffN^{eff}_{ec} are studied in this work.

  • N- : bulk layer, 50 μm\mu\mathrm{m}, 1×1014 cm−31\times10^{14}\ \mathrm{cm}^{-3}.

  • N buff : buff layer, 5.0 μm\mu\mathrm{m}, 1×1018 cm−31\times10^{18}\ \mathrm{cm}^{-3}.

  • N++ : substrate layer, 10 μm\mu\mathrm{m}, 1×1020 cm−31\times10^{20}\ \mathrm{cm}^{-3}.

In the Trapezoid-Type 4H-SiC LGAD, the width of “trapezoid” electric field is dominated by the thickness of gain layer dgaind_{gain}, but the electric field level is controlled by the effective doping of electric field control layer NeceffN_{\mathrm{ec}}^{\mathrm{eff}}. Figure 6 demonstrate the control action of electric field when the effective doping of electric field control layer NeceffN_{\mathrm{ec}}^{\mathrm{eff}} changed ±20%\pm20\%.

Image not extracted

Figure 6. The electronic field in gain layer of Trapezoid-Type 4H-SiC LGAD at U=500 V when when the doping level of electric field control layer NeceffN_{ec}^{\mathrm{eff}} changed ±20%\pm20\%.

Similarly, the I-V and 1/C21/C^2-VV curves are simulated for Trapezoid-Type 4H-SiC LGAD shown in Figure 7 and Figure 8. Only dgain=0.5 μmd_{\mathrm{gain}} = 0.5\ \mu\mathrm{m} and dgain=1.0 μmd_{\mathrm{gain}} = 1.0\ \mu\mathrm{m} are studied because the electric field layer is fixed to 0.1 μm0.1\ \mu\mathrm{m}. Same with the Triangle-Type 4H-SiC LGAD, the breakdown voltages could also be restrained in 500 V∼1000 V500\ \mathrm{V}\sim1000\ \mathrm{V} and the full depletion voltage VFD<500 VV_{\mathrm{FD}} < 500\ \mathrm{V} in our designs. It should be noted that another sudden-changing voltage VECV_{\mathrm{EC}} is appeared in Figure 8(a) and Figure 8(b) due to electric field control layer is added.

Image not extracted

(a)

Image not extracted

(b)

Figure 7. Leakage current for simulation at 4 different electric field control levels of Trapezoid-Type 4H-SiC LGAD and PIN: (a) dgain=0.5 μmd_{\mathrm{gain}} = 0.5\ \mu\mathrm{m}; (b) dgain=1.0 μmd_{\mathrm{gain}} = 1.0\ \mu\mathrm{m}. The colored lines are Triangle-Type 4H-SiC LGAD. The dotted gray line is PIN.

Image not extracted

Figure 8. 1/C21/C^2-VV for simulation at 4 different electric field control layer doping levels of Trapezoid-Type 4H-SiC LGAD and PIN: (a) dgain=0.5 μmd_{\mathrm{gain}}=0.5\ \mu\mathrm{m}; (b) dgain=1.0 μmd_{\mathrm{gain}}=1.0\ \mu\mathrm{m}. The colored lines are Triangle-Type 4H-SiC LGAD. The dotted gray line is PIN.

Simulation of gain for MIP

To determine the gain factor when MIPs pass through the 4H-SiC LGAD, we use the heavy ion which has the same e-h pairs generation with MIP in 4H-SiC material to obtain the gain factor. The gain factor in this work is defined as:

Gain=QLGADQPIN=∫0Ti(t)LGAD∫0Ti(t)PIN(5)\mathrm{Gain} = \frac{Q_{\mathrm{LGAD}}}{Q_{\mathrm{PIN}}} = \frac{\int_{0}^{T} i(t)_{\mathrm{LGAD}}}{\int_{0}^{T} i(t)_{\mathrm{PIN}}} \tag*{(5)}

where QQ is collected charges, i(t)i(t) is stimulated current by MIP and TT is collection time. Figure 9(a) and Figure 9(b) demonstrate the stimulated current by MIPs under different operating voltages. Compare with the stimulated current of PIN, The current gain for both type of 4H-SiC LGAD is >10> 10 when U=500 V. Under same operating voltage, the gain of Triangle-Type is higher than gain of Trapezoid-Type. It could be interpreted by using the profile of electric field shown in Figure 10(a), where the higher electric field peak for Triangle-Type dominates the gain factor although the Trapezoid-Type has higher average electric field E‾gain\overline{E}_{\mathrm{gain}}. The electric field levels shown in Figure 10(a) agree with the predication in Figure 1. Based on simulation, we determine the electric field is ∼3.2×106 V/cm\sim3.2 \times10^{6}\ V/cm for Triangle-Type and ∼2.3×106 V/cm\sim2.3 \times10^{6}\ V/cm for Trapezoid-Type to a 4H-SiC LGAD with dgain=0.5 μmd_{\mathrm{gain}} = 0.5\ \mu m.

Image not extracted

Figure 9. (a) the stimulated current by MIP in Triangle-Type 4H-SiC LGAD. The colored lines are Triangle-Type 4H-SiC LGAD under different operating voltages. The dotted gray line is PIN at U=500U=500 V. (b) the stimulated current by MIP in Trapezoid-Type 4H-SiC LGAD. The colored lines are Trapezoid-Type 4H-SiC LGAD under different operating voltages. The dotted gray line is PIN at U=500U=500 V.

Image not extracted

Figure 10. (a) the electric field near gain layer of Triangle-Type 4H-SiC LGAD, Trapezoid-Type 4H-SiC LGAD and PIN under the same operating voltage U=500U=500 V. (b) the slope of stimulated current by MIPs for Triangle-Type 4H-SiC LGAD and Trapezoid-Type 4H-SiC LGAD.

The time-response is described by the rising slope of stimulated current by MIP which is defined as max⁡(Ampl)trise\frac{\max(Ampl)}{t_{\mathrm{rise}}}, where the max⁡(Ampl)\max(Ampl) is the max value of stimulated current and triset_{\mathrm{rise}} is rising time. Figure 10(b) demonstrates the direct proportion with gain and the rising slope. And it indicates both types of 4H-SiC LGAD have the same time response for the same gain. Combined with the previous analysis that the Triangle-Type has a higher gain than Trapezoid-Type, the Triangle-Type is better for the application of fast MIP detection.

Efficiency of gain obtaining and stability

To compare the efficiency of gain obtaining for two types 4H-SiC LGAD, the relations between gain and the ratio U/VBDU/V_{BD} are studied. Figure 11(a) shows the Triangle-Type 4H-SiC LGAD has higher efficiency of gain obtaining because it has a higher gain factor than Trapezoid-Type at the same U/VBDU/V_{BD} value. But it also indicates the Triangle-Type is easier to reach the breakdown threshold, as reflected in the rapidly increasing of

Image not extracted

Figure 11. (a) the relations between gain and U/VBDU/V_{BD} for Triangle-Type 4H-SiC LGAD (dotted lines) and Trapezoid-Type 4H-SiC LGAD (solid lines). The different colored lines represents the different doping levels. (b) the relations between gain and U/VBDU/V_{BD} for different thickness of gain layer. The dotted lineS are Triangle-Type and solid lines are Trapezoid-Type. (c) the gain factor under operating voltage U=500 V at temperature from T=300 K to T=500 K.

gain when U/VBD>0.8U/V_{BD} > 0.8. Contrarily, all of Trapezoid-Type 4H-SiC LGADs behave more stable even if the U/VBD>0.9U/V_{BD} > 0.9.

Another piece of evidence that indicates the stability of the Trapezoid-Type 4H-SiC LGAD is shown in Figure 11(b). When the thickness of the gain layer increases from 0.5 μm0.5\ \mu\mathrm{m} to 1.0 μm1.0\ \mu\mathrm{m}, the Gain – (U/VBD)(U/V_{BD}) curves for Trapezoid-Type 4H-SiC LGAD are not changed that means the efficiency of gain obtaining do not rely on dgaind_{\mathrm{gain}}. For the Triangle-Type 4H-SiC LGAD, the gain factor decreases when the dgaind_{\mathrm{gain}} increases at the same value of U/VBDU/V_{BD}. It indicates the thinner gain layer has higher efficiency of gain obtaining but more easily breakdown. So the Trapezoid-Type 4H-SiC LGAD is better to consider its stability and robustness.

To investigate the temperature dependence and potential application in high temperature environment, the gain factors from T=300 KT=300\ \mathrm{K} to T=500 KT=500\ \mathrm{K} are simulated which are shown in Figure 11(c). Under the same operating voltage, the gain factor decreases with increasing of temperature. It is caused by the decreasing impact ionization coefficient depends on Hatakeyama model. The gain of both types are >10>10 when the temperature below 400 K400\ \mathrm{K}.

Summary

Based on the analytical analysis in § 2, we provide the policy to determine the doping level and thickness of gain layer in 4H-SiC LGAD. In our work, dgain=0.5 μmd_{\mathrm{gain}}=0.5\ \mu\mathrm{m} is adopted which has 50 μm50\ \mu\mathrm{m}, 1×1014 cm−31\times10^{14}\ \mathrm{cm}^{-3} bulk layer. The two types of LGAD structures are compared by simulation where the Triangle-Type has “triangle” electric field and Trapezoid-Type has “trapezoid” electric field. In the simulation, the gain >10>10 is achieved when the operating voltage UU between VFDV_{FD} and VBDV_{BD}. The Triangle-Type 4H-SiC LGAD is better for the application of fast MIP detection but also easily premature breakdown. The Triangle-Type 4H-SiC LGAD shows high stability and robustness but low efficiency of gain obtaining. It should be noticed that the simulation in this work is based on the specific configuration of physical parameters for 4H-SiC parameters. Different physical models impact the final results. Especially for the impact ionization coefficient predicated by different models[21, 22, 28, 29], the difference could be some magnitudes in 4H-SiC in our studied temperature range. So the study of practical devices is necessary in the future. The preliminary results of Trapezoid-Type 4H-SiC LGAD fabricated by Nanjing University (NJU)[30, 31] have already verified the process technology. Further study and optimization of NJU 4H-SiC LGAD are on going. We believe the more interesting results could be obtained for practical devices in the future. And it will help us to understand the impact ionization in the thin 4H-SiC layer like 4H-SiC LGAD structure.

Acknowledgment

This work has been supported by the National Natural Science Foundation of China (No. 11961141014), the State Key Laboratory of Particle Detection and Electronics (No. SKLPDE-ZZ-202218) under the CERN RD50 Collaboration framework.

References

  1. [1]ATLAS Collaboration. Technical Design Report for the ATLAS Inner Tracker Strip Detector, 2021. Technical report, CERN, Geneva, url:https://cds.cern.ch/record/2257755.
  2. [2]V. Sola et al. Ultra-Fast Silicon Detectors for 4D tracking. Journal of Instrumentation, 12(02), 2017. doi:10.1088/1748-0221/12/02/c02/02.DOI
  3. [3]G. Pellegrini et al. Technology developments and first measurements of Low Gain Avalanche Detectors (LGAD) for high energy physics applications. Nucl. Instrum. Methods A, 765, 2014. doi: 10.1016/j.nima.2014.06.008.DOI
  4. [4]H. F. W. Sadrozinski et al. 4D tracking with ultra-fast silicon detectors. Rep. Prog. Phys., 81(2), 2018. doi: 10.1088/1361-6633/aa94d3.
  5. [5]V. Sola et al. First FBK production of 50 um ultra-fast silicon detectors. Nucl. Instrum. Methods A, 924, 2019. doi: 10.1016/j.nima.2018.07.060.DOI
  6. [6]G. Giacomini et al. Development of a technology for the fabrication of Low-Gain Avalanche Diodes at BNL. Nucl. Instrum. Methods A, 934, 2019. doi: 10.1016/j.nima.2019.04.073.DOI
  7. [7]K. Wu et al. Design of Low Gain Avalanche Detectors (LGAD) with 400 keV ion implantation energy for multiplication layer fabrication. Nucl. Instrum. Methods A, 984, 2020. doi:10.1016/j.nima.2020.164558.DOI
  8. [8]Y.Y. Fan et al. Radiation hardness of the low gain avalanche diodes developed by NDL and IHEP in China. Nucl. Instrum. Methods A, 984, 2020. doi:10.1016/j.nima.2020.164608.DOI
  9. [9]S. Xiao et al. Beam test results of NDL Low Gain Avalanche Detectors (LGAD). Nucl. Instrum. Methods A, 989, 2021. doi:10.1016/j.nima.2020.164956.DOI
  10. [10]Y. Yang et al. Characterization of the first prototype NDL Low Gain Avalanche Detectors (LGAD). Nucl. Instrum. Methods A, 1011, 2021. doi:10.1016/j.nima.2021.165591.DOI
  11. [11]Y. Tan et al. Radiation effects on NDL prototype LGAD sensors after proton irradiation. Nucl. Instrum. Methods A, 1010, 2021. doi:10.1016/j.nima.2021.165559.DOI
  12. [12]G. Kramberger et al. Radiation effects in Low Gain Avalanche Detectors after hadronirradiations. Journal of Instrumentation, 10(07), 2015. doi:10.1088/1748-0221/10/07/p07006.DOI
  13. [13]M. Ferrero et al. Radiation resistant LGAD design. Nucl. Instrum. Methods A, 919, 2019. doi:10.1016/j.nima.2018.11.121.DOI
  14. [14]Francesco Moscatelli et al. Measurements and simulations of charge collection efficiency of p+/n junction SiC detectors. Nucl. Instrum. Methods A, 546(1):218–221, 2005. Proceedings of the 6th International Workshop on Radiation Imaging Detectors.DOI
  15. [15]T. Yang et al. Time resolution of the 4h-sic pin detector. Frontiers in Physics, 10, 2022. doi:10.3389/fphy.2022.718071.DOI
  16. [16]Y. Tan et al. Timing Performance Simulation for 3D 4H-SiC Detector. Micromachines, 13(1), 2022. doi:10.3390/mi13010046.DOI
  17. [17]R. Van Overstraeten et al. Measurement of the ionization rates in diffused silicon p-n junctions. Solid-State Electronics, 13(5), 1970. doi:10.1016/0038-1101(70)90139-5.DOI
  18. [18]J.D. Massey et al. Temperature Dependence of Impact Ionization in Submicrometer Silicon Devices. IEEE Transactions on Electron Devices, 53(9), 2006. doi:10.1109/TED.2006.881010.DOI
  19. [19]M. Mandurrino et al. Analysis and numerical design of Resistive AC-Coupled Silicon Detectors (RSD) for 4D particle tracking. Nucl. Instrum. Methods A, 959, 2020. doi:10.1016/j.nima.2020.163479.DOI

Paper details

vlnc:W_w9n3v8hm
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents