betaFeedback

WorksPhysics and Astronomy

Triply-Resonant Sum Frequency Conversion with Gallium Phosphide Ring Resonators

Abstract

We demonstrate quasi-phase matched, triply-resonant sum frequency conversion in 10.6-um-diameter integrated gallium phosphide ring resonators. A small-signal, waveguide-to-waveguide power conversion efficiency of 8%/mW is measured for conversion from telecom (1536 nm) and near infrared (1117 nm) to visible (647 nm) wavelengths with an absolute power conversion efficiency of 6.3% measured at saturation pump power. For the complementary difference frequency generation process, a single photon conversion efficiency of 7.2%/mW from visible to telecom is projected for resonators with optimized coupling. Efficient conversion from visible to telecom will facilitate long-distance transmission of spin-entangled photons from solid-state emitters such as the diamond NV center, allowing long-distance entanglement for quantum networks.

Introduction

Difference and sum frequency conversion in χ(2)\chi^{(2)} materials provide an efficient and general means to access new wavelengths with established sources. Conversion efficiency in these processes scales with field intensity, motivating resonant geometries to both increase per-unit power conversion efficiency and decrease the interaction volume and thus footprint. Resonant geometries are of particular interest for applications in quantum information in which devices must operate at the single photon level. Single photon frequency conversion processes, also called quantum frequency conversion (QFC), will enable a wider range of qubits to access telecommunication wavelengths, enabling long-distance entanglement for fiber-based quantum repeater networks [1, 2, 3, 4, 5, 6, 7]. Further, fine control of the converted photon wavelength could be used to erase inhomogeneities in emission wavelength, permitting high-fidelity remote entanglement of inhomogeneous qubits by two-photon interference. [8, 9, 10] QFC may also be useful as an upconversion mechanism for efficient room-temperature photon detection [11, 12] and could provide a bridge between disparate qubit platforms [13].

QFC based on a material’s second order nonlinear susceptibility χ(2)\chi^{(2)} utilizes a strong coherent pump to enable interactions between two single-photon modes, so it is restricted to sum- and difference-frequency generation (SFG and DFG) processes with three distinct wavelengths. Single-photon SFG/DFG has been demonstrated in macroscopic optical cavities [11, 14] and PPLN waveguides [7, 15, 16], with internal maximum photon conversion efficiencies as high as 86% for pump powers of hundreds of mW. In nanophotonic resonators, triply resonant QFC processes have been demonstrated using two detuned inputs on a single resonance [17, 18] or adjacent azimuthal resonances of the same transverse mode [19]. In both cases, two of the three wavelengths involved in the conversion process are restricted to a range of a few nanometers. However, implementing QFC interfaces for specific quantum emitters, e.g. the nitrogen-vacancy [20, 21] or silicon-vacancy [22, 23] in diamond, will typically require long jump frequency changes with three resonances at widely disparate wavelengths.

Model and design

The GaP ring resonators were designed to maximize waveguide-to-waveguide on-chip conversion efficiency. For a process that converts visible photons in the ω3\omega_3 input mode to telecom photons in the ω1\omega_1 output mode using a pump at ω2=∣ω3−ω1∣\omega_2 = \lvert\omega_3-\omega_1\rvert, the theoretical power conversion efficiency η\eta in the low-power limit is [30]:

ηP2,in=P1,outP2,inP3,in=64∣β∣2ω1ω2ω3Q12Q22Q32Qc1Qc2Qc3(1)\frac{\eta}{P_{2,\mathrm{in}}}=\frac{P_{1,\mathrm{out}}}{P_{2,\mathrm{in}}P_{3,\mathrm{in}}}=64\lvert\beta\rvert^2\frac{\omega_1}{\omega_2\omega_3}\frac{Q_1^2Q_2^2Q_3^2}{Q_{c1}Q_{c2}Q_{c3}} \tag*{(1)}

where QnQ_n and QcnQ_{cn} are the total and coupling quality factors of mode nn, and PnP_n is the input/output power for each mode. Small-signal or normalized conversion efficiency is defined as ηss=P1,out/P2,inP3,in\eta_{\mathrm{ss}}=P_{1,\mathrm{out}}/P_{2,\mathrm{in}}P_{3,\mathrm{in}}. Because the quality factors are primarily limited by material properties and fabrication, we focus on maximizing the nonlinear mode overlap β\beta, which encompasses the effects of mode field distribution and polarization, phase matching, and mode volume:

β=14ε0∫∑i,j,kχijk(2)E3i∗(E1jE2k+E2jE1k) dV∫ε1∣E1∣2 dV∫ε2∣E2∣2 dV∫ε3∣E3∣2 dV(2)\beta=\frac{1}{4\sqrt{\varepsilon_0}}\frac{\int\sum_{i,j,k}\chi_{ijk}^{(2)}E_{3i}^{*}(E_{1j}E_{2k}+E_{2j}E_{1k})\,dV}{\sqrt{\int\varepsilon_1\lvert E_1\rvert^2\,dV}\sqrt{\int\varepsilon_2\lvert E_2\rvert^2\,dV}\sqrt{\int\varepsilon_3\lvert E_3\rvert^2\,dV}} \tag*{(2)}

EnE_n and εn\varepsilon_n are the electric field distribution and relative permittivity for mode nn, and ii, jj, and kk are crystallographic directions of the nonlinear medium. The ring resonators were designed for 430 nm thick GaP on silicon oxide. Due to the zincblende crystal symmetry of GaP, χ(2)≠0\chi^{(2)} \ne0 for i≠j≠ki \ne j \ne k, so nonlinear interactions require mutually perpendicular field components in each mode. For a radially symmetrical structure in [1 0 0]-normal GaP, the nonlinear overlap β\beta becomes:

β=∣χ(2)∣4ε0∫N[(B1−iB2)ei(M+2)θ+(B1+iB2)ei(M−2)θ] dV∫ε1∣E1∣2 dV∫ε2∣E2∣2 dV∫ε3∣E3∣2 dVM=m1+m2−m3B1=E1z(E2rE3θ∗+E3r∗E2θ)+E2z(E1rE3θ∗+E3r∗E1θ)+E3z∗(E1rE2θ+E2rE1θ)B2=E1z(E2rE3r∗−E2θE3θ∗)+E2z(E1rE3r∗−E1θE3θ∗)+E3z∗(E1rE2r−E1θE2θ)(3)\begin{aligned} \beta&=\frac{\lvert\chi^{(2)}\rvert}{4\sqrt{\varepsilon_0}}\frac{\int_N\left[(B_1-iB_2)e^{i(M+2)\theta}+(B_1+iB_2)e^{i(M-2)\theta}\right]\,dV}{\sqrt{\int\varepsilon_1\lvert E_1\rvert^2\,dV}\sqrt{\int\varepsilon_2\lvert E_2\rvert^2\,dV}\sqrt{\int\varepsilon_3\lvert E_3\rvert^2\,dV}}\\ M&=m_1+m_2-m_3\\ B_1&=E_{1z}(E_{2r}E_{3\theta}^{*}+E_{3r}^{*}E_{2\theta})+E_{2z}(E_{1r}E_{3\theta}^{*}+E_{3r}^{*}E_{1\theta})+E_{3z}^{*}(E_{1r}E_{2\theta}+E_{2r}E_{1\theta})\\ B_2&=E_{1z}(E_{2r}E_{3r}^{*}-E_{2\theta}E_{3\theta}^{*})+E_{2z}(E_{1r}E_{3r}^{*}-E_{1\theta}E_{3\theta}^{*})+E_{3z}^{*}(E_{1r}E_{2r}-E_{1\theta}E_{2\theta}) \tag*{(3)} \end{aligned}

where EirE_{ir}, EizE_{iz}, and EiθE_{i\theta} are the radial, vertical, and azimuthal field components and mim_i is the azimuthal mode number of each mode.

The nonlinear overlap exhibits a sinc-like dependence on the quasi-phase matching (QPM) condition M=±2M=\pm2. The overlap is greatly diminished for single- or double-resonant processes, and vanishes entirely for unmatched triple resonance (M≠±2M \ne\pm2). Consequently, when the designed set of modes are tuned to triple resonance, it is unlikely that any other frequency conversion process with the same input wavelengths, such as second harmonic generation, will be significantly enhanced by the resonator. Each term in the overlap is a product of one vertical and two in-plane field components, which in practice restricts mode selection to one TM and two TE modes. The difference in interactions between radial and azimuthal field components in the M=+2M = +2 and M=−2M = -2 cases biases the overlap integral toward the inside and outside edge of the ring, respectively, which allows significant interactions between modes with even and odd symmetry [31].

The ring resonator was designed using the Lumerical MODE bent-waveguide solver to simulate propagation constants and nonlinear overlap for telecom, NIR, and visible modes. Two designs were explored. In the first design, the ring width and radius were optimized to maximize β\beta while satisfying the M=−2M = -2 quasi-phase matching condition for TE00\mathrm{TE}_{00}, TE00\mathrm{TE}_{00}, and TM03\mathrm{TM}_{03} modes at 1550 nm, 1081.4 nm, and 637 nm, respectively (Supplement 1). The final ring dimensions for this design are a radius of 5.3 μ\mum, measured to the center of the ring, with ring width varied from 675–704 nm in 1 nm increments to compensate for fabrication variations. The second design utilized TE00\mathrm{TE}_{00}, TE01\mathrm{TE}_{01}, and TM04\mathrm{TM}_{04} modes at 1550 nm, 1081.4 nm, and 637 nm. This mode combination allowed more than a two-fold increase in simulated ∣β∣2\lvert\beta\rvert^2 compared to the first design in exchange for potentially reduced quality factors. The fabricated devices exhibited lower SFG efficiency compared to the first design (Supplement 1) and will not be discussed further here.

From Eq. (1), the small-signal conversion efficiency is maximized when all three modes are critically coupled (Qc=2QQ_{\mathrm{c}} = 2Q), while the quantum limit of the photon conversion efficiency can be increased to approach unity by overcoupling the input and output modes [30]. With a simulated nonlinear overlap of ∣β∣2=27.8 J−1\lvert\beta\rvert^2 = 27.8\ \mathrm{J}^{-1} for the first ring design, a critically coupled device with a combined total quality factor of (Q1Q2Q3=1015Q_1 Q_2 Q_3 = 10^{15}) is simulated to provide a waveguide-to-waveguide photon conversion efficiency of ∼13.5%/mW\sim13.5\%/\mathrm{mW} between visible and telecom wavelengths. Wrapped-waveguide coupling regions were designed to provide a range of target coupling quality factors for each mode (Supplement 1). As shown in Figure 1a, both infrared modes were coupled to a single waveguide, while the visible mode was coupled to a separate waveguide.

Figure 1. (a) Device layout and SEM image of a GaP nonlinear ring resonator coupled to input/output waveguide circuits, one for 637–647 nm visible light (blue) and one combining 1530–1565 nm telecom (red) and 1080–1120 nm NIR (yellow) light. Each coupling circuit includes two grating couplers to allow single-wavelength transmission measurements in addition to the SFG measurement marked on the SEM. (b) Free-space coupled microscope setup for device characterizations and SFG measurements. Cross-polarization and the pinhole (PH) are used to eliminate reflected/scattered input light. IR: infrared, SC: supercontinuum, PD: photodiode, BS: beamsplitter, DC: dichroic, HWP: half-wave plate, BP: band-pass filter, LP: long-pass filter. Input and output filter wavelengths were adjusted for different measurement wavelengths. (c) The transmission measurements from telecom, near-infrared and visible resonances in device SFG01, along with fitted Fano/Lorentzian curves. Background is approximated with linear functions. Ring cross-sections with vertical (visible) or radial (telecom and NIR) electric field distributions are inset for each mode. Transmission at each wavelength was measured using a tunable laser input and wavelength-appropriate photodiode. Due to difficulties with measuring and fitting the specific resonances used for triply-resonant SFG testing, the fits shown here use different instances of the same family of resonances.

Fabrication

The photonic devices were fabricated in a 427 nm-thick [100]-normal GaP membrane on 1 μ\mum SiO2_2 on silicon. The GaP membrane was grown by gas-source molecular-beam epitaxy on an intermediate 300 nm Al0.8_{0.8}Ga0.2_{0.2}P sacrificial layer on a bulk GaP substrate. The sacrificial layer was etched in 3:100 HF:H2_2O to release the 2 mm square GaP membrane. The membrane was wet transferred to the oxide substrate [32], which was cleaned with solvents, O2_2 plasma, and treated with HMDS adhesion-promoter. The photonic circuit pattern was written by 100 keV electron beam lithography in a ∼100\sim100 nm HSQ resist layer, which was developed with 25% TMAH in water. The resist pattern was transferred to the GaP layer by an inductively-coupled plasma reactive ion etch (ICP-RIE) using a Cl/Ar/N2_2 (1.0/6.0/3.0 sccm) plasma, which selectively stops at the oxide layer. After fabrication, the HSQ resist could not be removed without potentially damaging the GaP or the oxide substrate, so it was left as partial cladding.

Passive device characterization

The setup shown in Figure 1b was used for both passive and frequency-conversion device testing. Passive device testing consisted of transmission measurements at each wavelength band, which were used to determine the quality factors of the three modes and the grating coupler efficiencies near the resonant wavelengths. The telecom resonances were characterized by scanning an input laser from 1530 nm to 1565 nm and recording the device transmission on an infrared photodiode.

The measured total quality factors of the telecom TE00\mathrm{TE}_{00} mode ranged from ∼0.9−2.9×105\sim0.9 - 2.9 \times10^{5}. Visible and near-infrared resonances were characterized via transmission spectroscopy with a broadband supercontinuum laser input and grating spectrometer collection. Devices with promising SFG performance were selected for further characterization using scanning narrowband sources (632–640 nm for visible, 1070–1130 nm for NIR). In this subset of devices, visible and NIR quality factors of ∼2.5−3×104\sim2.5 - 3 \times10^{4} and ∼4.5−6×104\sim4.5 - 6 \times10^{4} were measured, respectively. The transmission measurements for the most efficient SFG device (SFG01) are shown in Figure 1c, with telecom, NIR, and visible quality factors of 1.1×1051.1 \times10^{5}, 4.6×1044.6 \times10^{4}, and 2.8×1042.8 \times10^{4}, respectively.

Triply-resonant device identification

Finding devices that could be tuned to quasi-phase matched triple resonance based on the passive transmission measurements proved difficult due to shallow transmission dips from non-critically coupled resonances in many devices, along with the highly multi-mode nature of the ring resonators in the visible band. Instead, we identified triply-resonant devices using rapid measurements of frequency conversion performance. As illustrated in Figure 2, frequency conversion processes that are close to triple resonance have greatly enhanced efficiency which depends strongly on the detuning between the converted light and the output resonance wavelength. Consequently, a near triply-resonant device under resonant excitation of two input modes will produce converted light that is both particularly bright and highly sensitive to detuning determined by the device temperature.

Figure 2. (a) The power density of the Whitelase Micro supercontinuum (SCL) laser, with the filtered wavelength band used as an input for SFG marked in green. The wavelength bands for the telecom tunable input laser (red) and visible output collection filter (blue) are also marked. Below is an illustration of the temperature-dependent SFG measurement used to identify triple-resonant SFG processes as described in the text. (b) Supercontinuum-pumped SFG measurements for device SFG01, showing dependence on device temperature and telecom-band input wavelength. Top is a linear-scale colormap and bottom is a logarithmic-scale colormap. The red line marks the telecom-band resonance, and the yellow line marks the input wavelengths that produce SFG light on resonance with the visible-band mode. Conversion efficiency is maximized when both conditions can be satisfied simultaneously (triple resonance).

Due to the availability of high-quality lasers in the telecom band and detectors in the visible band, we used telecom-to-visible SFG measurements to characterize frequency conversion performance. The designed complementary DFG process is expected to have similar photon conversion efficiency. In order to efficiently explore SFG performance in a three-dimensional parameter space (two input wavelengths and device temperature), we use a broadband supercontinuum laser (SCL) as the pump-band input (filtered to 1000-1200 nm), and combine it with a tunable laser in the telecom band (1530-1565 nm) with approximately 300 µW of power in the waveguide. Converted visible light is collected using a 775 nm short pass filter, 637/22 nm bandpass filter, and a spatial filter to remove both scattered supercontinuum light and second harmonic converted light from the telecom laser. Some portion of the supercontinuum pump provides resonant excitation to every NIR-band mode. Now, when the telecom laser scans over a resonance, visible light is produced by SFG processes within the ring, enhanced by the telecom and a NIR-band mode. The observed intensity of the converted visible light is a function of the detuning of the constituent resonances. A phase-matched visible resonance will not contribute much additional enhancement if the SFG wavelength is substantially detuned. The detuning can be modified by changing device temperature, but the SFG efficiency is not significantly affected until the SFG wavelength approaches the resonance. At this point, SFG efficiency becomes highly sensitive to temperature and peaks when the converted light is on resonance. Consequently, a strong temperature dependence in the intensity of the SCL-pumped SFG in a device indicates a phase-matched triple-resonant SFG process.

We performed supercontinuum-pumped SFG measurements on 123 ring resonators at temperatures from 16–40 °C in 4 °C increments. Most of the tested devices produced some measurable SFG light within this temperature range. Eight resonators with bright, strongly temperature-dependent SFG were selected for further characterization and designated SFG01-SFG08. Supercontinuum-pumped SFG measurements were repeated with a finer temperature sweep to find the optimal operating temperature for each device. As shown for device SFG01 in Figure 2b, the SFG intensity peak red-shifts with increasing temperature to follow the high-QQ telecom resonance. The peak intensity is maximized at a device temperature of ∼25\sim25°C at which the condition of triple resonance met. This condition is apparent on a logarithmic scale in which two SFG peaks can be observed at each temperature: the telecom-band resonance, and a second peak at the input wavelengths that produce SFG light on resonance with the visible-band mode. Similar measurements for the other seven devices are presented in Supplement 1.

Spectra of the SFG output were taken to determine the visible SFG wavelength. The visible SFG wavelength combined with the measured telecom input resonance uniquely determines the pump frequency. As shown in Table 1, the narrower ring resonators exhibited triple resonance with modes at ∼1550\sim1550, ∼1107\sim1107, and ∼647\sim647 nm, and wider rings at ∼1536\sim1536, ∼1117\sim1117, and ∼647\sim647 nm. The discrepancy between the designed and measured process wavelengths may be due to fabrication variations, particularly in the ring coupling regions and sidewall angles.

DeviceWidth (nm)Opt. T (°C)Est. ηγ\eta_\gamma (%/mW)Telecom λ\lambda (nm)SFG λ\lambda (nm)Pump λ\lambda (nm)
SFG01698258.001536.7646.821117.0
SFG02682185.7511552.5646.511107.2
SFG0368425∼5.7\sim5.71552.8646.591107.9
SFG0468222.54.381552.4646.41107.6
SFG05699221.771536.3646.661116.7
SFG06701251.361537647.661119.4
SFG0767918.50.911550.9645.91106.9
SFG08696310.381536.5646.661116.6

Table 1. Ring width, operating temperature, efficiency and estimated SFG process wavelengths for SFG processes in eight triply-resonant ring resonators, based on supercontinuum-pumped SFG measurements. The visible wavelength of the dominant SFG process was measured with a spectrometer, and the pump-band wavelength was calculated from the telecom input and SFG output wavelengths. Conversion efficiency was measured directly for device SFG01, and estimated for other devices based on a comparison to this value. The efficiency estimate for device SFG03 is less precise due to a damaged visible-band output grating coupler.

Frequency conversion efficiency

While the broadband SCL pump allows efficient identification of triple-resonant devices, continuous and narrow-band pulsed inputs allow more precise control of the power used to excite a targeted frequency conversion process. We measure the SFG small signal conversion efficiency of the brightest devices (SFG01 and SFG02) with a 1080-1120 nm tunable CW laser as a pump in place of the SCL. At the optimal temperature found with the SCL measurements, a 2D scan of both excitation lasers over their respective resonances was performed while monitoring the input power from each laser as shown in Figure 3a,Figure 3b. Similar to the temperature tuning data in Figure 2b, we again observe SFG enhancement from the visible (blue line) and telecom resonances (red line). SFG measurements with the pump laser near its resonance required additional attenuation to avoid saturating the detector with the peak intensity. Rescaling the signal to compensate for the attention resulted in a heightened noise floor, hiding the enhancement from the pump-band resonance alone. Waveguide-to-waveguide small signal conversion efficiency was calculated from measured input and output powers, grating efficiency, and microscope efficiency (Supplement 1). For device SFG01, the peak small-signal efficiency found with this measurement was 4.9%/mW.

Three-panel plots showing input wavelength dependence and power dependence of SFG conversion efficiency

Figure 3. (a) Input wavelength dependence of small-signal SFG power conversion efficiency for device SFG01 at its optimal temperature (25°C), using CW telecom and pump inputs with average powers of 100 µW and 82 µW in the waveguide. The red line marks the SFG enhancement from resonant excitation of the telecom mode, and the blue line shows enhancement from to the visible mode applied to combinations of input wavelengths that produce an on-resonance SFG wavelength. The collected SFG signal was attenuated to avoid detector saturation when the NIR wavelength approached resonance, resulting in exaggerated background noise from ∼1117.55 − 1117.65 nm. (b) Detail of the small-signal conversion efficiency peak for device SFG01 around the NIR resonance. The linewidth of the efficiency peak corresponds to a pump mode quality factor of 5.7×1045.7 \times10^{4}, with a maximum conversion efficiency of ∼5%/mW. (c) Power dependence of absolute conversion efficiency for device SFG01. The top plot shows conversion using low-power CW inputs, varying the NIR-band input power. The bottom plot shows conversion using a constant, low-power CW NIR input with a variable-power pulsed telecom input, which allows higher instantaneous excitation powers while avoiding the effects of resonator heating.

Figure 3c (top) gives the absolute power conversion efficiency for SFG01 in the small signal regime. A linear dependence on pump power is observed as expected. To obtain the maximum power conversion, the roles of the telecom and NIR laser were swapped due to the need for higher pump power which can be achieved with an erbium doped fiber amplifier added to the telecom input. Additionally, to minimize resonator heating and optical bistability, a telecom electro-optic modulator was used to pulse the telecom laser. The weaker NIR laser remained in CW mode. We note that the pulse lengths (100 ns) and duty cycle (1%) used are comparable to what would be utilized in single diamond defect applications. As shown in Figure 3c (bottom), an absolute power conversion efficiency of 6.3% was measured for a peak telecom input power in the waveguide of 1.8 mW. In devices targeting single photon conversion, pump depletion is not a factor and over coupling of the single photon modes will minimize back-conversion, allowing much higher maximum conversion efficiency. Fitted curves for the CW and pulsed power dependence measurements yielded small-signal conversion efficiencies 9.5%/mW and 8%/mW, respectively. The variation in measured conversion efficiency may be due to slight variations in input laser alignment or gradual changes in the HSQ cladding [31] altering the optimal temperature of the device.

The small-signal conversion efficiency found for device SFG02 with similar measurements was ∼0.37−0.59%/mW\sim0.37-0.59\%/\mathrm{mW} (Supplement 1). Estimates of the efficiency for devices SFG03-SFG08 were found by comparing the supercontinuum-pumped SFG intensities to device SFG01, and are given in Table 1.

Conclusion and outlook

In triple resonant ring resonators, we demonstrate a waveguide-to-waveguide small signal power SFG conversion efficiency of 8%/mW and measure a 6.3% absolute power conversion efficiency. At critical coupling, the expected SFG power conversion efficiency is ∼17%/mW\sim17\%/\mathrm{mW}, which corresponds to a visible-to-telecom DFG photon (not power) conversion efficiency of ∼7.2%/mW\sim7.2\%/\mathrm{mW}. The lower DFG value is due to the difference in initial and converted photon frequencies. The outlook for the triple resonance microring approach for large wavelength shift quantum frequency conversion is promising. Absolute conversion efficiency can be further increased with higher quality factors. We have observed undercoupled quality factors as high as ∼3×105\sim3 \times10^{5} at both telecom and visible wavelengths for similar GaP-on-insulator devices (Supplement 1), suggesting a small-signal DFG photon conversion efficiency of ∼45%/mW\sim45\%/\mathrm{mW} is possible in the near term, with near-unity conversion in over-coupled devices with sufficient pump power.

Efficiency, however, is only one aspect in evaluating QFC performance. Because 637 nm to telecom conversion requires a pump at a shorter wavelength than the output, telecom noise photons can potentially be generated by spontaneous down conversion, a known issue in PPLN devices [33]. There may, however, be an additional advantage to resonant devices which suppress undesired frequency conversion processes by a combination of phase matching and resonance. Optimal waveguide-resonator coupling and efficient off-chip coupling, while theoretically straightforward, pose engineering challenges. Perhaps the most critical challenge, however, will be achieving triple resonance from a precise defect optical transition frequency to a target telecom frequency. This will require further advancement in multiple independent, or quasi-independent resonator tuning mechanisms [31, 34]. Once achieved, the impact of triply-resonant devices would extend to wavelength multiplexing for quantum networks and the elimination of emitter wavelength inhomogeneity.

Acknowledgement

This material is based upon work supported by the National Science Foundation under grants EFMA-1640986 (photonic design, fabrication and passive device testing) and U.S. Department of Energy, Office of Science, National Quantum Information Science Research Centers, Co-design Center for Quantum Advantage (C2QA) under contract number DE-SC0012704 (frequency conversion testing). The photonic devices were fabricated at the Washington Nanofabrication Facility, a National Nanotechnology Coordinated Infrastructure (NNCI) site at the University of Washington which is supported in part by funds from the National Science Foundation (awards NNCI-2025489, 1542101, 1337840 and 0335765). We thank Mo Li for the use of optical test equipment.

Supplemental Information

Photonic integrated circuit design considerations

Aperiodic grating couplers were designed to provide off-chip coupling at each wavelength with minimal footprint. Grating designs for each wavelength were generated using a simplified model treating the grating as series of discrete, independent scattering elements in a waveguide. Scatterer widths and spacings were optimized to maximize overlap between upward-scattered light and a target Gaussian mode shape using a sampled discrete hill climbing algorithm. The detailed coupling behavior from waveguide to free space was simulated by Lumerical 3D FDTD for each grating design candidate. The grating design that provided the highest coupling into a single spot in free space over the target wavelength band was selected. If the simulated grating efficiency peak was offset from the target wavelength, all lengths in the grating design were scaled by up to 5% to red- or blue-shift the efficiency curve. For grating couplers intended for multi-wavelength operation, two design approaches were used. First, gratings that had been designed for one wavelength were FDTD simulated at the second wavelength. If an existing design also provided reasonable performance in the second wavelength band, it would be used as a multi-wavelength coupler. Alternatively, grating designs can be co-optimized for free space coupling at both wavelengths using the hill-climbing algorithm to maximize the product of the two single-wavelength objective functions. However, this second strategy was not employed in this work. The measured grating coupler efficiencies at the telecom, NIR, and visible resonant wavelengths ranged between 11-20%, 5.5-8.5% and 1-2% in these devices. At the design wavelengths of 1550, 1080, and 637 nm, the respective grating efficiencies were simulated as 20%, 17%, and 40%, but the NIR and visible gratings were operated at non-optimal wavelengths.

Wrapped-waveguide ring resonator coupling regions were designed using Lumerical MODE bent-waveguide eigenmode simulations for an extended supermode analysis. For different combinations of coupling waveguide width (wwgw_{wg}) and ring-waveguide separation distance (dd), mode profiles and propagation constants were simulated for all modes in the combined ring and waveguide structure. For each combined-structure mode, mode overlaps were calculated for both the ring resonator mode and the targeted waveguide mode. During a single pass through the coupling region, light in the ring mode is divided between the combined-structure modes based on the mode overlaps. The relative phases of these modes evolve as the light propagates in the combined structure for some angular distance θ\theta around the ring. The mode phases affect how much light is coupled into the waveguide mode at the end of the coupling region, and how much remains in the ring. The coupling quality factor QcQ_c can then be calculated based on the single-pass ring-to-waveguide coupling and the round-trip propagation time of the ring mode. Values of wwgw_{wg}, dd, and θ\theta were selected to provide targeted values of QcQ_c, which were chosen in a range around experimentally observed quality factors in similar photonic devices [32].

Due to previous observations of pump-band ring modes coupling to telecom-band output waveguides and vice versa, both infrared ring modes were coupled to a single waveguide in these devices. Wrapped-waveguide coupling regions were designed for the first ring design, which used fundamental radially-polarized (TE) modes at both wavelengths. However, a wrapped waveguide design could not be found that could accommodate both the telecom mode and higher-order pump mode in the second ring design. Instead, a straight-waveguide coupling region was used for the infrared modes for that ring design. For straight waveguides, single-pass coupling was simulated using 3D FDTD, and coupling quality factor was calculated as normal. The visible and infrared QcQ_c targets used for each ring design can be found in Fig. SI.5.

The primary design variables for the ring resonators are ring width ww and radius rr, since the GaP layer thickness is constant across the MBE chip. The ring dimensions are optimized to maximize nonlinear overlap β\beta while satisfying the quasi-phase matching condition M=±2M = \pm2 (Eqn. (3)) for a selected set of telecom (1550 nm), visible (637 nm), and pump (1081.4 nm) modes. At each design point, propagation constants and mode profiles for each mode are simulated using Lumerical MODE bent-waveguide eigenmode solver. The propagation constants are used to calculate azimuthal mode numbers mnm_n, which may be fractional if the precise design wavelengths are not resonant, and M=m1+m2−m3M = m_1 + m_2 - m_3. Nonlinear overlap β\beta is calculated from the mode profiles. To find valid ring designs, first an arbitrary combination of rr and ww is evaluated. If quasi-phase matching (QPM) is not satisfied, the ring width is iteratively modified until a valid design is found (M≈±2M \approx\pm2). Ring dimensions and β\beta for this design are recorded. Then, ring radius is adjusted, and ring width is again tuned until the same QPM condition is satisfied. This process is repeated while following increasing trends in β\beta (usually, toward smaller radius) until either β\beta is maximized or the ring width or radius becomes too small to confine the highest-wavelength mode without severe degradation of quality factor.

Figure SI.4. SEM images and mode profiles for the primary (a) and alternative (b) ring designs fabricated for this work.

The first ring design in this work was designed with the mode combination of TE00\mathrm{TE}_{00}, TE00\mathrm{TE}_{00}, and TM03\mathrm{TM}_{03}, respectively, for the telecom, pump, and visible modes. With a ring width of 690 nm and radius of 5300 nm, this mode combination was simulated to satisfy the QPM condition M=−2M=-2, with a nonlinear overlap of ∣β∣2=27.8 J−1|\beta|^2=27.8\ \mathrm{J}^{-1}. As described in Eqn. (3), a ring resonator in a [1 0 0]-normal zincblende crystal requires two TE modes and one vertically-polarized (TM) mode to provide significant nonlinear overlap β\beta. The shortest wavelength mode was selected to be the TM mode due to previous observations and simulations that TM mode quality factor is more sensitive to material thickness than TE modes. Satisfying the QPM condition purely by mode engineering requires a higher-order visible mode, with the trade-off that β\beta is usually higher for modes that are closer to the fundamental. The TE00_{00}/TE00_{00}/TM03_{03} combination was selected because it allows phase matching with a ring width that is wide enough to easily accommodate the fundamental telecom mode. Ring designs with TE00_{00}/TE00_{00}/TM02_{02} modes could provide higher values of β\beta, but achieving quasi-phase matching with these modes requires substantially narrower rings with poor confinement of the telecom mode. Conversely, TE00_{00}/TE00_{00}/TM04_{04} allows for wider ring resonators at the cost of severe degradation of the nonlinear overlap. A second ring design, shown in Fig. SI.4, was developed using a TE00_{00}/TE01_{01}/TM04_{04} telecom/pump/visible mode combination, which produced a higher nonlinear overlap ∣β∣2=68. J−1|\beta|^2=68.\ \mathrm{J}^{-1} with a ring width of 810 nm and radius of 4425 nm. However, due to poor coupling and reduced quality factor of the pump mode, devices fabricated with the second design exhibited substantially lower conversion efficiency, as shown in Fig. SI.5.

Figure SI.5. Supercontinuum-pumped SFG performance survey showing peak SFG intensity at 24°C for all devices of ring designs 1 (a) and 2 (b). All devices were excited with similar input powers, so the measured SFG intensities approximately correspond to conversion efficiencies relative to other devices. While most of the devices are not at their optimal temperatures for SFG, particularly bright devices are likely to be within temperature tuning range (14 − 40°C) of triple resonance. Data points are colored according to the simulated coupling quality factors for each device, which are summarized for each ring design in the tables below.

Ring 1Tele9.0×10^51.2×10^51.7×10^5
VisibleNIR1.0×10^52.0×10^56.5×10^5
2.0×10^4036
5.6×10^4147
1.1×10^5258

Table SI.5a.

Ring 2Tele.1.2×10^52.2×10^53.5×10^5
VisibleNIR2.2×10^54.0×10^57.3×10^5
2.2×10^4036
5.2×10^4147
9.2×10^4258

Table SI.5b.

Supercontinuum pump survey of all devices

In order to compensate for variations in the fabrication process, arrays of devices of both ring designs were fabricated with varying ring widths and coupling region parameters. The supercontinuum-pumped SFG method described in the main paper was used to identify candidate devices for more detailed frequency conversion testing. First, a survey of peak SFG intensity at room temperature was performed on all operational ring resonators of both designs, shown in Fig. SI.5. Because the brightest observed devices of the second design produced roughly 10% of the SFG intensity of the first design rings, subsequent testing was focused on the first design. The supercontinuum-pumped SFG survey was repeated for the design 1 devices at temperatures from 16–40°C to identify devices with the strong temperature dependence indicating a triply-resonant conversion process. Eight devices with bright, temperature-sensitive SFG were selected for additional testing. Supercontinuum-pumped SFG was measured at 0.5°C intervals to find the optimal temperature and corresponding peak SFG intensity for each of these devices, as shown in Fig. SI.6.

Temperature dependence of supercontinuum-pump SFG intensity for devices SFG01–SFG08

Figure SI.6. Temperature dependence of supercontinuum-pump SFG intensity for devices SFG01-SFG08 (a-h). For each device, a logarithmic-scale color plot shows the SFG dependence on both temperature and telecom-band input wavelength. Every pump-band mode is always resonantly excited by some part of the filtered supercontinuum laser input (1000-1200 nm). The primary intensity line follows the telecom-band resonance, while dimmer lines associated with visible-band resonances tune across the telecom resonance to produce peaks in the SFG conversion efficiency. A linear-scale plot of the peak SFG intensity at each temperature is also shown for each device.

The two devices that exhibited the highest peak SFG intensity, designated SFG01 and SFG02, were selected for calibrated conversion efficiency testing. The SFG testing methods and performance for SFG01 are described in the main text. As shown in Fig. SI.7, device SHG02 was characterized using similar procedures, which found a small-signal power conversion efficiency of 370–580%/W. Due to mode splitting in this device, converted light was observed coupling out of both visible-band grating couplers. The conversion efficiency was calculated from the output power of a single grating coupler.

Figure SI.7. (a) Transmission measurements of the telecom, near-infrared, and visible resonances in device SFG02, along with fitted Lorentzian curves and quality factors. Background is approximated with linear function. (b) Supercontinuum-pumped SFG intensity as a function of temperature. (c) Power conversion efficiency of device SFG02 as a function of telecom (blue) and NIR (red) input power. For each data series, the other wavelength input is constant and weak relative to the variable input power.

For both devices, power conversion efficiency is calculated as η=Pout/Pin\eta= P_{\mathrm{out}}/P_{\mathrm{in}}, where PoutP_{\mathrm{out}} is the visible SFG power in the output waveguide and PinP_{\mathrm{in}} is either the telecom or NIR power in the input waveguide, depending which wavelength is designated as the pump in each measurement. In either case, the small-signal conversion efficiency ηss=Pvis/PtelecomPNIR\eta_{\mathrm{ss}} = P_{\mathrm{vis}}/P_{\mathrm{telecom}}P_{\mathrm{NIR}} is the slope of the power dependence of η\eta at low input powers. Photon conversion efficiency is power conversion efficiency scaled by the ratio of input and output photon energies. For each wavelength, power in the waveguide is calculated from off-chip power measurements combined with the grating coupler efficiencies for the device under test. For the telecom and NIR band inputs, the input transmission efficiencies from the point of measurement to the grating coupler were 56.5% and 77.2%, respectively. The total collection and detection efficiency of the visible-band output at 647 nm was 2.4%.

Highest quality factors measured in GaP-on-insulator devices

The GaP-on-insulator platform has the potential for significantly higher performance if higher Q-factors can be obtained. The Q-factors in the highest performing SFG devices in this study are lower than what has been obtained in other devices. We have observed telecom QQ’s as high as 290,000 on the SFG chip (Fig. SI.5a). We have measured visible QQ’s ranging from 200,000-490,000 in 290-nm thick GaP disk resonators on nitride (Fig. SI.5b,c). These quality factors are all measured in the undercoupled regime. At critical coupling, Q’s may reduce by up to a factor of two. For the visible transmission measurements, an add-drop port geometry is utilized with the drop port monitored.

Figure SI.8. (a) Transmission measurements of the telecom resonances in a SFG device, along with fitted Lorentzian curves and quality factors. Background is approximated with linear function. (b–c) Drop port transmission measurements of TM-mode visible resonances in a 5-µm diameter GaP disk resonator on silicon nitride, obtained by scanning a tunable laser. The positions of each resonance are determined to be (b) 768.38 ± 0.16 nm and (c) 635.05 ± 0.11 nm respectively, with Lorentzian fits giving quality factors as large as half million. Here both resonances are in the undercoupled regime demonstrating the large intrinsic quality factor in the visible band. The PL lineshape is fitted using a Fano and a Lorentzian function.

References

  1. [1]P. Kumar, “Quantum frequency conversion,” Opt. Lett. 15, 1476–1478 (1990).
  2. [2]M. Bock, P. Eich, S. Kucera, M. Kreis, A. Lenhard, C. Becher, and J. Eschner, “High-fidelity entanglement between a trapped ion and a telecom photon via quantum frequency conversion,” Nat. communications 9, 1–7 (2018).
  3. [3]T. van Leent, M. Bock, R. Garthoff, K. Redeker, W. Zhang, T. Bauer, W. Rosenfeld, C. Becher, and H. Weinfurter, “Long-distance distribution of atom-photon entanglement at telecom wavelength,” Phys. review letters 124, 010510 (2020).DOI
  4. [4]S. Zaske, A. Lenhard, C. A. Keßler, J. Kettler, C. Hepp, C. Arend, R. Albrecht, W.-M. Schulz, M. Jetter, P. Michler et al., “Visible-to-telecom quantum frequency conversion of light from a single quantum emitter,” Phys. review letters 109, 147404 (2012).DOI
  5. [5]A. Tchebotareva, S. L. N. Hermans, P. C. Humphreys, D. Voigt, P. J. Harmsma, L. K. Cheng, A. L. Verlaan, N. Dijkhuizen, W. de Jong, A. Dréau, and R. Hanson, “Entanglement between a diamond spin qubit and a photonic time-bin qubit at telecom wavelength,” Phys. Rev. Lett. 123, 063601 (2019).DOI
  6. [6]T. Walker, K. Miyanishi, R. Ikuta, H. Takahashi, S. V. Kashanian, Y. Tsujimoto, K. Hayasaka, T. Yamamoto, N. Imoto, and M. Keller, “Long-distance single photon transmission from a trapped ion via quantum frequency conversion,” Phys. review letters 120, 203601 (2018).DOI
  7. [7]A. Dréau, A. Tchebotareva, A. E. Mahdaoui, C. Bonato, and R. Hanson, “Quantum frequency conversion of single photons from a nitrogen-vacancy center in diamond to telecommunication wavelengths,” Phys. Rev. Appl. 9, 064031 (2018).
  8. [8]S. Ates, I. Agha, A. Gulinatti, I. Rech, M. T. Rakher, A. Badolato, and K. Srinivasan, “Two-photon interference using background-free quantum frequency conversion of single photons emitted by an InAs quantum dot,” Phys. review letters 109, 147405 (2012).pubmed.ncbi.nlm.nih.gov/23083286
  9. [9]J. H. Weber, B. Kambs, J. Kettler, S. Kern, J. Maisch, H. Vural, M. Jetter, S. L. Portalupi, C. Becher, and P. Michler, “Two-photon interference in the telecom c-band after frequency conversion of photons from remote quantum emitters,” Nat. Nanotechnol. 14, 23–26 (2019).DOI
  10. [10]D. S. Levonian, R. Redjem, B. Machielse, E. N. Knall, M. K. Bhaskar, C. M. Knaut, R. Bekenstein, H. Park, M. Lončar, and M. D. Lukin, “Optical entanglement of distinguishable quantum emitters,” Phys. Rev. Lett. 128, 213602 (2022).DOI
  11. [11]M. A. Albota and F. N. Wong, “Efficient single-photon counting at 1.55 μm by means of frequency upconversion,” Opt. letters 29, 1449–1451 (2004).pubmed.ncbi.nlm.nih.gov/15259709
  12. [12]H. Rütz, K.-H. Luo, H. Suche, and C. Silberhorn, “Quantum frequency conversion between infrared and ultraviolet,” Phys. Rev. Appl. 7, 024021 (2017).DOI
  13. [13]M. Allgaier, V. Ansari, L. Sansoni, C. Eigner, V. Quiring, R. Ricken, G. Harder, B. Brecht, and C. Silberhorn, “Highly efficient frequency conversion with bandwidth compression of quantum light,” Nat. Commun. 8, 14288 (2017).
  14. [14]A. Samblowski, C. E. Vollmer, C. Baune, J. Fiurášek, and R. Schnabel, “Weak-signal conversion from 1550 to 532 nm with 84% efficiency,” Opt. Lett. 39, 2979–2981 (2014).DOI
  15. [15]T. Guerreiro, E. Pomarico, B. Sanguinetti, N. Sangouard, J. Pelc, C. Langrock, M. Fejer, H. Zbinden, R. T. Thew, and N. Gisin, “Interaction of independent single photons based on integrated nonlinear optics,” Nat. communications 4, 1–5 (2013).DOI
  16. [16]J. S. Pelc, L. Ma, C. R. Phillips, Q. Zhang, C. Langrock, O. Slattery, X. Tang, and M. M. Fejer, “Long-wavelength-pumped upconversion single-photon detector at 1550 nm: performance and noise analysis,” Opt. Express 19, 21445–21456 (2011).DOI
  17. [17]A. Stolk, K. L. van der Enden, M.-C. Roehsner, A. Tepe, S. O. Faes, S. Cadot, J. van Rantwijk, I. t. Raa, R. Hagen, A. Verlaan et al., “Telecom-band quantum interference of frequency-converted photons from remote detuned nv centers,” arXiv preprint arXiv:2202.00036 (2022).DOI
  18. [18]J.-Q. Wang, Y.-H. Yang, M. Li, X.-X. Hu, J. B. Surya, X.-B. Xu, C.-H. Dong, G.-C. Guo, H. X. Tang, and C.-L. Zou, “Efficient frequency conversion in a degenerate χ(2) microresonator,” Phys. Rev. Lett. 126, 133601 (2021).
  19. [19]X. Ye, S. Liu, Y. Chen, Y. Zheng, and X. Chen, “Sum-frequency generation in lithium-niobate-on-insulator microdisk via modal phase matching,” Opt. Lett. 45, 523–526 (2020).DOI
  20. [20]A. Dréau, A. Tchebotareva, A. El Mahdaoui, C. Bonato, and R. Hanson, “Quantum frequency conversion of single photons from a nitrogen-vacancy center in diamond to telecommunication wavelengths,” Phys. review applied 9, 064031 (2018).
  21. [21]R. Ikuta, T. Kobayashi, S. Yasui, S. Miki, T. Yamashita, H. Terai, M. Fujiwara, T. Yamamoto, M. Koashi, M. Sasaki et al., “Frequency down-conversion of 637 nm light to the telecommunication band for non-classical light emitted from nv centers in diamond,” Opt. express 22, 11205–11214 (2014).DOI
  22. [22]D. Huang, A. Abulnaga, S. Welinski, M. Raha, J. D. Thompson, and N. P. de Leon, “Hybrid III-V diamond photonic platform for quantum nodes based on neutral silicon vacancy centers in diamond,” Opt. Express 29, 9174–9189 (2021).DOI
  23. [23]E. Bersin, N. Wan, M. Bhaskar, D. Levonian, R. Riedinger, C. Langrock, M. M. Fejer, M. Lukin, P. B. Dixon, S. Hamilton, and D. Englund, “A low-noise telecom interface for silicon-vacancy quantum network nodes,” in 2021 Conference on Lasers and Electro-Optics (CLEO), (2021), pp. 1–2.DOI
  24. [30]I. B. Burgess, A. W. Rodriguez, M. W. McCutcheon, J. Bravo-Abad, Y. Zhang, S. G. Johnson, and M. Lončar, “Difference-frequency generation with quantum-limited efficiency in triply-resonant nonlinear cavities,” Opt. express 17, 9241–9251 (2009).DOI
  25. [31]L. Thiel, A. D. Logan, S. Chakravarthi, S. Shree, K. Hestroffer, F. Hatami, and K.-M. C. Fu, “Precise electron beam-based target-wavelength trimming for frequency conversion in integrated photonic resonators,” Opt. Express 30, 6921–6933 (2022).DOI
  26. [32]A. D. Logan, M. Gould, E. R. Schmidgall, K. Hestroffer, Z. Lin, W. Jin, A. Majumdar, F. Hatami, A. W. Rodriguez, and K.-M. C. Fu, “400%/W second harmonic conversion efficiency in 14 μm-diameter gallium phosphide-on-oxide resonators,” Opt. Express 26, 33687–33699 (2018).
  27. [33]C. L. Morrison, M. Rambach, Z. X. Koong, F. Graffitti, F. Thorburn, A. K. Kar, Y. Ma, S.-I. Park, J. D. Song, N. G. Stoltz, D. Bouwmeester, A. Fedrizzi, and B. D. Gerrardot, “A bright source of telecom single photons based on quantum frequency conversion,” Appl. Phys. Lett. 118, 174003 (2021).DOI
  28. [34]X. Lu, A. Rao, G. Moille, D. A. Westly, and K. Srinivasan, “Universal frequency engineering tool for microcavity nonlinear optics: multiple selective mode splitting of whispering-gallery resonances,” Photon. Res. 8, 1676–1686 (2020).DOI

Paper details

vlnc:W_wb263yyj
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents