betaFeedback

WorksPhysics and Astronomy

Viscoelastic wetting: Cox-Voinov theory with normal stress effects

Abstract

The classical Cox-Voinov theory of contact line motion provides a relation between the macroscopically observable contact angle, and the microscopic wetting angle as a function of contact line velocity. Here we investigate how viscoelasticity, specifically the normal stress effect, modifies wetting dynamics. Using the thin film equation for the second-order fluid, it is found that the normal stress effect is dominant at small scales. We show that the effect can be incorporated in the Cox-Voinov theory through an apparent microscopic angle, which differs from the true microscopic angle. The theory is applied to the classical problems of drop spreading and dip-coating, which shows how normal stress facilitates (inhibits) the motion of advancing (receding) contact lines. For rapid advancing motion, the apparent microscopic angle can tend to zero in which case the dynamics is described by a new regime that was already anticipated in Boudaoud (2007).

Banner appropriate to article type will appear here in typeset article

Introduction

The motion of a contact line governs a variety of phenomena, such as drops moving on surfaces, drop spreading, and coating applications. This problem has been widely explored for Newtonian fluids over the last decades [19, 5, 40]. Within the hydrodynamic framework of wetting, the macroscopic flow is often described using the Cox-Voinov theory [9, 44], which connects the macroscopic contact angle to the microscopic angle. The relation between these angles is intricate, since the balance of the viscous shear forces (viscosity η\eta) and capillary forces (surface tension γ\gamma) leads to a “bending” of the interface in a region near the contact line. Macroscopically, the result can be expressed as a relation for the apparent outer (macroscopic) angle θapp,o\theta_{\mathrm{app},o}, defined in Figure 1(a,b) for droplet spreading and dip-coating, respectively. An explicit treatment of the problem is often given using the thin film (lubrication) framework,

Moving contact lines for viscoelastic liquids encountered in drop spreading and dip-coating

Figure 1. Moving contact lines for viscoelastic liquids encountered in drop spreading (a) and dip-coating (b). At a large scale, the flow is characterised by a macroscopic apparent contact angle θapp,o\theta_{\mathrm{app},o}, seen at an outer scale ℓo\ell_o. (c) Microscopic view of the interface. (ci_i) the highest shear rates are encountered close to the contact line (slip length scale λ\lambda), where polymers become highly stretched. This gives rise to large normal stresses that “bend” the interface to angles below the equilibrium contact angle θe\theta_e. In this paper we introduce θapp,i\theta_{\mathrm{app},i} as the resulting apparent microscopic angle. (cii_{ii}) On a scale-free region λ≪x≪ℓo\lambda\ll x \ll\ell_o, the interface slope follows the Voinov solution reflecting the visco-capillary balance; θapp,i\theta_{\mathrm{app},i} serves as the apparent inner boundary condition at small scale. (ciii_{iii}) At large scales, the slope is given by the apparent outer angle θapp,o\theta_{\mathrm{app},o}.

Abstract must not spill onto p.2 see for e.g., Eggers & Fontelos [16], which leads to a dependence of the macroscopic angle on the contact line speed UU through the form [9, 44]:

θapp,o3=θe3±9Caln⁡(ℓoℓi),Ca=ηUγ.(1)\theta_{\mathrm{app},o}^{3} = \theta_e^{3} \pm9\mathrm{Ca}\ln\left(\frac{\ell_o}{\ell_i}\right), \qquad\mathrm{Ca} = \frac{\eta U}{\gamma}. \tag*{(1)}

Here θe\theta_e is the (microscopic) equilibrium angle, and Ca the capillary number. The “±” depends on whether the contact line is advancing (+) or receding (-). The formula contains an inner length scale ℓi\ell_i, necessary to regularise the moving contact line singularity [26], as well as an outer length scale ℓo\ell_o that reflects the macroscopic geometry of the problem (e.g., the radius of a spreading drop). The strict validity of (1) is restricted to small contact angles and small capillary numbers, due to assumptions underlying the analysis [9, 44, 16]. Yet, it has been successfully applied to a large class of problems [40].

Many applications like the deposition of pesticides on plant leaves or ink-jet printing involve polymer solutions. Such fluids exhibit non-Newtonian rheology such as shear-thinning viscosity and viscoelasticity, which can affect the contact line dynamics as has been demonstrated through several experimental studies (Wei et al. 2009a,b; Wang et al. 2007; Seevaratnam et al. 2007; Han & Kim 2013; Kim & Rothstein 2015). For the canonical problem of liquid spreading on a substrate, it was found that a non-Newtonian drop spreading on completely wetting surfaces still followed the long-time power-law dynamics R∼tnR \sim t^n, where R(t)R(t) is the drop radius, and the exponent nn is slightly smaller than the Cox-Voinov-Tanner’s law n=1/10n = 1/10 [33]. This comparatively weak effect could be attributed to both shear-thinning viscosity and the consequence of normal stress effects. During the very early stages of drop spreading, ensuing after a droplet is gently brought into contact with a substrate, the spreading exhibits much larger exponents, with n=1/2n = 1/2 for low-viscosity Newtonian drops [4]. Interestingly, the addition of polymers has no measurable effect on this rapid spreading [7, 51]. Similarly, during drop impact, the initial spreading phase is nearly unaffected by the presence of polymers [1, 20, 36].

By contrast, the retraction of a droplet, e.g. after an impact, is strongly influenced by the presence of polymers [3]. The typical retraction velocity was found to decrease with the (first) normal stress coefficient ψ\psi, following a scaling U∼1/ψU \sim1/\sqrt{\psi} [1]. This result can be interpreted from the balance between the normal stress near the contact line ∼ψ(U/ℓ)2\sim\psi(U/\ell)^2 and the Laplace pressure γh′′∼γθe2/ℓ\gamma h^{\prime\prime} \sim\gamma\theta_e^2/\ell, giving a typical velocity

Uψ=θeγℓψ,(2)U_{\psi} = \theta_e \sqrt{\frac{\gamma\ell}{\psi}}, \tag*{(2)}

where ℓ\ell is to be interpreted as a microscopic cutoff length [1], very much like ℓi\ell_i in (1). The best-fit of experimental data gave ℓ\ell to be of the order of tens of microns [1], which is larger than the expected nanometric length used in Newtonian fluids. Alternatively, this result can be obtained from a balance of capillary force γ(cos⁡θ−cos⁡θe)∼γθe2/2\gamma(\cos\theta-\cos\theta_e) \sim\gamma\theta_e^2/2, and viscoelastic force ψU2/ℓ\psi U^2/\ell induced by the extra tension along the streamlines [1]. The addition of polymers also changes the drop shedding behind a sliding droplet (Xu et al. 2018).

In fact, polymers have been observed to be strongly stretched at a contact line (during retraction) [39] and stretched and depleted at the contact line (during spreading) [37] and are sometimes left on the surface after the retraction [53]. This could be induced by either non-hydrodynamic polymer-surface interactions [22], or shear-induced migration [23, 38]. However, it has remained a challenge to disentangle the possible roles of all these mechanisms, which in part is due to the lack of a hydrodynamic framework for viscoelastic wetting.

The aim of the present study is to explore systematically the influence of viscoelastic normal stress on the motion of contact lines. There have been several studies dedicated to quantifying normal stress effects in wetting flows. Numerical schemes have been developed using the phase-field method and polymer rheological models like Oldroyd-B or Giesekus [52, 47, 46] and results using these were found to be consistent with prior experimental observations [49, 23], in that the viscoelastic stresses, confined to a small region near the contact line, had only a mild effect on the contact-line motion of spreading drops. Boudaoud [6] introduced a phenomenological thin-film model that includes normal stress effects. Solving the resulting equation in the specific case of complete wetting, the advancing contact angle is found to follow

θapp,o3=9Caln⁡(ℓoℓVE),ℓVE=ψU2η.(3)\theta_{\mathrm{app},o}^{3} = 9\mathrm{Ca}\ln\left(\frac{\ell_o}{\ell_{\mathrm{VE}}}\right), \qquad\ell_{\mathrm{VE}} = \frac{\psi U}{2\eta}. \tag*{(3)}

This expression can be seen as a form of the Cox-Voinov law (1), with θe=0\theta_e = 0 and the microscopic regularizing length provided by a viscoelastic length ℓVE\ell_{\mathrm{VE}}. The latter corresponds to the product between the contact line velocity UU and the typical relaxation time of the liquid ψ/η\psi/\eta. However, it has remained unclear whether this theory can actually be derived from any tensorial constitutive relation, and how these results carry over to partial wetting conditions, for which the equilibrium contact angle θe\theta_e must play a role. Also, as the equation derived by Boudaoud [6] (given as equation (3)) does not admit any solutions with partial wetting conditions, it cannot be applied to receding contact lines - which is crucial to understand the observed strong effects of normal stresses on the retraction velocity (Bartolo et al. [1]).

In this paper, we study how normal stress affects both advancing and receding contact line motion of partially wetting fluids. Through our analysis we demonstrate the strong effect of viscoelastic normal stress on receding contact lines which was previously observed in the experiments of Bartolo et al. [1]. Our paper is based on an expansion of the stress to second-order in the shear rate, an approximation which exhibits a normal stress effect. The so-called second-order fluid is appropriate for modelling slow and steady flows in the weak viscoelasticity limit ([43, 30, 11]). This constitutive relation was recently given a long-wave expansion (Datt et al. [10]), yielding a thin film equation that can be used to describe contact line motion in the presence of normal stress. The approach resembles somewhat the analysis by Han & Kim [24], who used corner solutions of the second-order fluid to estimate how normal stress affects the pressure inside the liquid. However, the thin film description by Datt et al. [10] results from a systematic long-wave expansion (naturally involving the gradient of pressure, rather than the pressure), and has the additional benefit of applying beyond the no-slip condition to relieve the moving contact line singularity. We focus on the case of partial wetting using a Navier-slip condition as a microscopic regularisation, so that the slip length λs\lambda_s appears as the inner scale. The central result of this paper consists of the modified form of the Cox-Voinov law,

θapp,o3=θe3−3ψU2θe4γλs±9Caln⁡(ℓoλs),(4)\theta_{\mathrm{app},o}^{3} = \theta_e^{3} - \frac{3\psi U^{2}\theta_e}{4\gamma\lambda_s} \pm9\mathrm{Ca}\ln\left(\frac{\ell_o}{\lambda_s}\right), \tag*{(4)}

which now exhibits an explicit dependence on the normal stress coefficient ψ\psi. A dependence of the Cox-Voinov relation on ∼U2\sim U^{2} was also suggested by Kim & Rothstein [27], but in that study the sign was proposed to be different for advancing (+) and receding (-) motion. Here we find that normal stress always leads to a smaller macroscopic contact angle. Comparing the first two terms on the right hand side of (4), we identify a dimensionless normal stress parameter,

N=ψU2γλsθe2.(5)N = \frac{\psi U^{2}}{\gamma\lambda_s\theta_e^{2}}. \tag*{(5)}

This dimensionless number N∼(U/Uψ)2N \sim(U/U_\psi)^2 can be seen as the viscoelastic equivalent of the capillary number, comparing the contact line speed to the intrinsic velocity UψU_\psi defined in (2). Indeed, as we will show, the derivation of (4) requires N≪1N \ll1 in a way similar to Ca≪1\mathrm{Ca} \ll1. The physical picture emerging from the viscoelastic Cox-Voinov theory is sketched in Figure 1(c). The modification with respect to the Newtonian case appears only at small scales, where the bending of the interface due to normal stress dominates over the viscous bending. The form of the contact angle law in (4) can then be interpreted in terms of an apparent microscopic angle θapp,i\theta_{\mathrm{app},i}, as shown in Figure 1(c), of the form

θapp,i3=θe3(1−34N).(6)\theta_{\mathrm{app},i}^{3} = \theta_e^{3}\left(1-\frac{3}{4}N\right). \tag*{(6)}

This angle decreases with viscoelasticity, both for advancing and receding contact lines, as the viscoelastic normal stress parameter depends on U2U^{2}. We recall that (4) is derived under the assumption of weak viscoelasticity, i.e. N≪1N \ll1. Importantly, however, when N≳1N \gtrsim1, another regime of strong viscoelasticity can emerge. As a result, the complete wetting solution of (3) (Boudaoud [6]) is recovered, even when the substrate is partially wetting. § 2 provides the detailed derivations of these results. Subsequently, § 3 explores the consequences of viscoelasticity for drop spreading, drop retraction and dip-coating. Finally, the paper closes with a discussion in § 4.

Modified Cox-Voinov law

Second-order fluid thin-film equation

We investigate a moving three-phase contact line, by considering a liquid film on a rigid surface. We choose a reference frame in which the contact line is at a fixed position x=0x = 0 and the solid surface is moving at a speed UU. We treat the problem with the lubrication approximation, which assumes relatively small angles. To include the effect of normal stress differences, we use the simplest viscoelastic fluid model containing normal stresses, i.e. the second-order fluid model (Tanner [43]). This model offers a good description of polymer solution rheology for steady flows in the weakly viscoelastic limit.

The lubrication equation for steady contact line motion with Navier-slip boundary condition has been derived recently for the second-order fluid (Datt et al. [10]). Denoting the interface profile as h(x)h(x) (see Figure 1), the lubrication equation reads

γh′′′=−3ηUh(h+3λs)−34(ψ(Uh+3λs)2)′(7)\gamma h''' = -\frac{3\eta U}{h(h+3\lambda_s)}-\frac{3}{4}\left(\psi\left(\frac{U}{h+3\lambda_s}\right)^2\right)' \tag*{(7)}

where λs\lambda_s is the Navier-slip length. The introduction of a molecular mechanism, here the slip length, is necessary to regularise the well-known moving contact line singularity (Huh & Scriven [26]; Bonn et al. [5]; Snoeijer & Andreotti [40]). Setting ψ=0\psi= 0, we recover the standard Newtonian lubrication equation (Duffy & Wilson [14]; Oron et al. [32]). The extra viscoelastic term in equation (7) is of the form of the gradient of normal stress, which is quadratic in shear rate. A very similar lubrication equation was obtained previously in Boudaoud [6], using scaling estimates for the components of the stress tensor. The resulting equation differs from (7) in two ways: slip is ignored and the prefactor in front of the viscoelastic term is not correct. We emphasise here that the second-order fluid thin-film equation is asymptotically equivalent to the Oldroyd-B model for weakly viscoelastic steady flows (see Appendix in Datt et al. [10]), ensuring the validity of (7). Importantly, the viscoelastic term scales as 1/h31/h^3 whereas the viscous term scales as 1/h21/h^2. Hence, we anticipate the normal stress to be negligible in the large hh limit with respect to the viscous term. The viscoelastic term is subdominant in the region far from the contact line, where viscous shear and capillary forces balance (see region (cii_{ii}) in Figure 1). A consequence is that the structure of the Cox-Voinov law still holds with normal stress, and normal stress effects are important only at small scales.

We thus focus on the inner region near the contact line, in which the typical film thickness scale is λs\lambda_s. We therefore rescale hh and xx as

X=xθe3λs,H(X)=h3λs,λ=λsθe,δ=3ηUγθe3=3Caθe3,(8)X=\frac{x\theta_e}{3\lambda_s},\qquad H(X)=\frac{h}{3\lambda_s},\qquad\lambda=\frac{\lambda_s}{\theta_e},\qquad\delta=\frac{3\eta U}{\gamma\theta_e^3}=\frac{3\mathrm{Ca}}{\theta_e^3}, \tag*{(8)}

where the lateral scale has been rescaled by 3λs/θe3\lambda_s/\theta_e to enforce slopes of order 1 and to scale out the equilibrium angle. We also introduced a rescaled slip length λ\lambda and capillary number δ\delta following Eggers [15]. The lubrication equation then becomes

H′′′=−δ(1H2+H−ℓVE3λH′(H+1)3)(9)H''' = -\delta\left(\frac{1}{H^2+H} - \frac{\ell_{\mathrm{VE}}}{3\lambda}\frac{H'}{(H+1)^3}\right) \tag*{(9)}

where viscoelastic effects are quantified by the dimensionless ratio ℓVE/λ\ell_{\mathrm{VE}}/\lambda.

Equation (9) holds both for advancing (δ>0\delta> 0) and receding (δ<0\delta< 0) contact lines. In this section, we focus on advancing contact lines, for which the boundary conditions are (Eggers [15]):

H(0)=0,H′(0)=1,H′′(∞)=0,(10)H(0) = 0,\qquad H'(0) = 1,\qquad H''(\infty) = 0, \tag*{(10)}

fixing the position of the contact line and the equilibrium angle condition, respectively. The third condition H′′(∞)=0H''(\infty) = 0, which can only be imposed for advancing contact lines (Duffy & Wilson [14]), matches any outer solution that has an asymptotically small curvature toward the contact line.

We perform direct numerical integration of the system (9)-(10), by using the continuation code AUTO-07P (Doedel et al. [13]). Typical profiles H(X)H(X) are shown in Figure 2(a) for δ=10−2\delta= 10^{-2} and changing the ratio ℓVE/λ\ell_{\mathrm{VE}}/\lambda to vary the strength of normal stresses. The normal stress effects tend to lower the slope of the interface profile, though each of the profiles exhibits the same microscopic contact angle H′(0)=1H'(0) = 1 (see Figure 2(b)). Asymptotically, in the large-XX limit, the interface slopes cubed all follow the same behavior, as

Advancing contact line profiles and parameter $a$

Figure 2. Advancing contact line: (a) Interface profile H(X)H(X) obtained from numerical integration of (9),(10), with reduced capillary number δ=10−2\delta= 10^{-2}. The inset shows a zoom near the contact line, illustrating that all profiles have the same microscopic contact angle. (b) Cube of the interface slope H′(X)H'(X), as function of distance from the contact line. Different colors correspond to varying normal stress effect quantified by ℓVE/λ\ell_{\mathrm{VE}}/\lambda. (c) The parameter aa, obtained from fitting Equation (11) to the large-XX limit of H′(X)H'(X) is plotted as a function of ℓVE/λ\ell_{\mathrm{VE}}/\lambda. The dots indicate the cases of figures (a) and (b) using the same color code. For a>0a > 0, the parameter a=(θapp,i/θe)3a = (\theta_{\mathrm{app},i}/\theta_{\mathrm{e}})^3 can be interpreted in terms of the apparent microscopic contact angle, and is well described by (16) (red dashed line). A regime of “apparent complete wetting” emerges when a<0a < 0, captured by (27) (green dashed line).

H′3≃a+3δln⁡(eX),(11)H'^{3} \simeq a + 3\delta\ln(eX), \tag*{(11)}

and differ by a vertical offset position denoted aa, which depends on ℓVE/λ\ell_{\mathrm{VE}}/\lambda, as shown in Figure 2(c). This asymptotic behavior relates to the Voinov solution, which is classically found in moving contact line problems, reflecting the visco-capillary balance (see region (ciic_{\mathrm{ii}}) in Figure 1). We introduce in (11) a factor e=exp⁡(1)e = \exp(1) inside the logarithm for convenience, so that the Newtonian solution corresponds to a=1a = 1 (as shown below). Hence, as anticipated, the normal stress effect does not modify the large scale asymptotic behavior of the inner solution, but induces a non-trivial offset in the Voinov solution. In the next two subsections, we determine the offset aa by using asymptotic expansions, in the weak and strong viscoelastic limit respectively.

Weak viscoelasticity: apparent microscopic angle

The standard approach to determine the interface profile near the contact line analytically is via a perturbation expansion of (9) in the small parameter δ\delta [25, 15]:

H(X)=H0(X)+δH1(X)+O(δ2).(12)H(X) = H_0(X) + \delta H_1(X) + O(\delta^2). \tag*{(12)}

Here, supposing weak viscoelasticity, we assume explicitly the ratio ℓVE/λ\ell_{\mathrm{VE}}/\lambda to be of order ∼1\sim1. The zeroth-order solution satisfies H0′′′=0H_0''' = 0, which from the boundary conditions (10) gives H0=XH_0 = X. At the first order in δ\delta, the interface profile follows

H1′′=−1X2+X+ℓVE3λ1(1+X)3,(13)H_1'' = -\frac{1}{X^2+X}+\frac{\ell_{\mathrm{VE}}}{3\lambda}\frac{1}{(1+X)^3}, \tag*{(13)}

with boundary conditions H1′(0)=0H_1'(0) = 0 and H1′′(∞)=0H_1''(\infty) = 0. Integration of equation (13) then gives

H1′=−Xln⁡X+(1+X)ln⁡(1+X)+ℓVE6λ(11+X−1)≃ln⁡X+1−ℓVE6λ,(14)H_1'=-X\ln X+(1+X)\ln(1+X)+\frac{\ell_{\mathrm{VE}}}{6\lambda}\left(\frac{1}{1+X}-1\right)\simeq\ln X+1-\frac{\ell_{\mathrm{VE}}}{6\lambda}, \tag*{(14)}

where the last step represents the X→∞X\to\infty asymptotic behavior. Combined with the zeroth-order solution, the large-XX asymptotic behavior of the interface slope in the small-δ\delta limit is

H′≃1+δ(ln⁡X+1−ℓVE6λ)+O(δ2).(15)H'\simeq1+\delta\left(\ln X+1-\frac{\ell_{\mathrm{VE}}}{6\lambda}\right)+O(\delta^2). \tag*{(15)}

Raising this result to the third power and comparing to equation (11), we obtain the sought-after offset constant

a=1−12δℓVEλ.(16)a=1-\frac{1}{2}\frac{\delta\ell_{\mathrm{VE}}}{\lambda}. \tag*{(16)}

Compared to the Newtonian case where a=1a=1, the interface slope indeed decreases due to the presence of normal stress effects. The dimensional form of equation (11) reads

h′3=(θapp,i)3+9Caln⁡(exθe3λs).(17)h'^3=(\theta_{\mathrm{app},i})^3+9\mathrm{Ca}\ln\left(\frac{ex\theta_e}{3\lambda_s}\right). \tag*{(17)}

Here we introduce the apparent microscopic angle θapp,i\theta_{\mathrm{app},i} (see Figure 1), that depends on the normal stress parameter NN as,

(θapp,i)3=aθe3=θe3(1−34N),(18)(\theta_{\mathrm{app},i})^3=a\theta_e^3=\theta_e^3\left(1-\frac{3}{4}N\right), \tag*{(18)}

where we used ℓVE/λ=3N/(2δ)\ell_{\mathrm{VE}}/\lambda=3N/(2\delta). We identify equation (17) as a modified Cox–Voinov solution where the equilibrium Young contact angle θe\theta_e has been modified to an apparent microscopic angle θapp,i\theta_{\mathrm{app},i} (see (18)). This result corresponds to equation (4) in § 1. The numerical data agree very well with this prediction for small to intermediate values of ℓVE/λ\ell_{\mathrm{VE}}/\lambda (see red dashed lines in Figure 2(c)). However, a significant deviation is observed at large ℓVE/λ\ell_{\mathrm{VE}}/\lambda, which coincides with a<0a<0 (grey zone in Figure 2(c)). To understand the breakdown of (16), we recall that the underlying perturbation expansion assumed both H′H' and ℓVE/λ\ell_{\mathrm{VE}}/\lambda to remain of order unity, which is clearly violated at large ℓVE/λ\ell_{\mathrm{VE}}/\lambda. Instead, one observes the formation of a flat film region where H′≃0H' \simeq0 in the large viscoelastic limit (see Figure 2(a) & (Figure 2b)), indicating onset of a new regime. The transition between the two regimes occurs when the apparent microscopic angle goes to zero θapp,i→0\theta_{\mathrm{app},i} \to0, which occurs when

θe3∼ψU2θeγλs⟹ℓVEλ∼1δ.(19)\theta_{\mathrm{e}}^3 \sim\frac{\psi U^2\theta_{\mathrm{e}}}{\gamma\lambda_{\mathrm{s}}} \Longrightarrow\frac{\ell_{\mathrm{VE}}}{\lambda} \sim\frac{1}{\delta}. \tag*{(19)}

This estimate is consistent with Figure 2(c), where δ=10−2\delta= 10^{-2}, for which the perturbation expansion (16) breaks down around ℓVE/λ∼1/δ∼102\ell_{\mathrm{VE}}/\lambda\sim1/\delta\sim10^2. The next section is dedicated to a description of the new regime at large ℓVE/λ\ell_{\mathrm{VE}}/\lambda, named strong viscoelasticity.

Strong viscoelasticity: (apparent) complete wetting

We interpret the behavior at large ℓVE/λ\ell_{\mathrm{VE}}/\lambda as a regime of “apparent complete wetting”. Indeed, the purple and brown solutions in Figure 2(b) exhibit an extended flat zone with H′≈0H' \approx0, resembling a situation of complete wetting condition, even though H(0)=1H(0) = 1. In the flat film region, the film curvature is very small, such that the capillary term is subdominant. Hence, the governing balance of (7) involves the viscous and viscoelastic term, from which one identifies ℓVE\ell_{\mathrm{VE}} as the natural lateral length scale. Physically, this implies that the information of the partial wetting nature of the problem, encoded in θe\theta_{\mathrm{e}}, is lost across the flat film: as it only modifies the profiles at a length scale ∼λ\sim\lambda (see Figure 2(b)), but this is “screened” by the flat wetting film on a length scale ℓVE\ell_{\mathrm{VE}}.

We proceed in the asymptotic analysis using ℓVE\ell_{\mathrm{VE}} as the relevant length on the flat film region. We assume, and validate a posteriori, that we can drop the slip length λs\lambda_{\mathrm{s}} from (7), in the large ℓVE/λ\ell_{\mathrm{VE}}/\lambda limit. Hence, we introduce the rescaling

ξ=xℓVE,H=h[ℓVE(3Ca)]1/3,(20)\xi= \frac{x}{\ell_{\mathrm{VE}}}, \qquad\mathcal{H} = \frac{h}{\left[\ell_{\mathrm{VE}}(3\mathrm{Ca})\right]^{1/3}}, \tag*{(20)}

for which equation (7) becomes

H′′′=−1H2+H′H3.(21)\mathcal{H}''' = -\frac{1}{\mathcal{H}^2}+\frac{\mathcal{H}'}{\mathcal{H}^3}. \tag*{(21)}

Here we dropped the slip terms, which is consistent as long as ℓVE/λ≫δ−1/3\ell_{\mathrm{VE}}/\lambda\gg\delta^{-1/3}, which is indeed satisfied in the strong viscoelastic limit. We notice that equation (21) resembles the thin-film equation with a disjoining pressure (see page 398 in Eggers & Fontelos [16]), which is used to model contact lines in complete wetting. Within this analogy, the effective “disjoining pressure” is −3ψU2/(4h2)-3\psi U^2/(4h^2), similar to the standard van der Waals disjoining pressure −A/(6πh3)-A/(6\pi h^3), where AA is the Hamaker constant. We employ boundary conditions

H(−∞)=0,H′(−∞)=0,H′′(+∞)=0,(22)\mathcal{H}(-\infty) = 0, \qquad\mathcal{H}'(-\infty) = 0, \qquad\mathcal{H}''(+\infty) = 0, \tag*{(22)}

where the first two conditions correspond to the formation of the film, replacing the partial wetting condition at ξ=0\xi= 0. Similarly to the § 2.2, since viscoelasticity only acts at small scales, the large distance asymptotic behavior is given by the Voinov solution (see (11)), which using the new scales reads

H′3≃3ln⁡(ξξ0).(23)\mathcal{H}'^3 \simeq3\ln\left(\frac{\xi}{\xi_0}\right). \tag*{(23)}

The offset aa has been replaced by an unknown constant ξ0\xi_0, which remains to be found.

The system (21)–(22) is exactly the problem analysed in Boudadoud (2007) up to a trivial rescaling, which we now understand to emerge as the limit of large ℓVE/λ\ell_{\mathrm{VE}}/\lambda. In the flat film region, the curvature is nearly zero and the capillary term drops out, such that the dominant balance involves viscous stress and normal stress. Towards the flat film, equation (21) reduces to

H′≃H(24)\mathcal{H}' \simeq\mathcal{H} \tag*{(24)}

to leading order. The viscous-viscoelastic solution takes the form of an exponentially growing solution H≃eξ\mathcal{H} \simeq e^\xi, with a prefactor that can be set to unity, owing to the translational invariance of (21) and (22). A more refined analysis of the asymptotic behavior of H\mathcal{H} in the ξ→−∞\xi\to-\infty limit leads to the asymptotic expression (Boudaoud [6]):

H≃eξ+c+e23ξe−3ξ/2+c−e−23ξe−3ξ/2(25)\mathcal{H} \simeq e^\xi+ c_{+}e^{\frac{2}{3}\xi}e^{-3\xi/2} + c_{-}e^{-\frac{2}{3}\xi}e^{-3\xi/2} \tag*{(25)}

where c±c_{\pm} are constants; using the boundary condition for ξ→−∞\xi\to-\infty leads to c+=0c_{+}=0. We solve equation (21) numerically, using equation (25) as an initial condition, where c−c_{-} is treated as a shooting parameter to ensure H′′(ξ→∞)=0\mathcal{H}''(\xi\to\infty)=0. Fitting the numerically-obtained slope H′(ξ)\mathcal{H}'(\xi) in the large-ξ\xi limit, typically ξ=108\xi=10^{8}, with the Voinov solution (Bender & Orszag [2]; Eggers & Fontelos [16]), we find a universal value of ξ0≈1.16\xi_{0} \approx1.16 (see Snoeijer & Eggers [42] for details of the numerical calculation).

In dimensional units, the contact line solution at large xx gives

h′3=9Caln⁡(xℓVEξ0).(26)h'^{3}=9\mathrm{Ca}\ln\left(\frac{x}{\ell_{\mathrm{VE}}\xi_{0}}\right). \tag*{(26)}

This has the same form of the Cox-Voinov solution for complete wetting, i.e. when θe=0\theta_{e}=0, where ℓVE\ell_{\mathrm{VE}} now offers the regularisation length, replacing the microscopic scale. This was also demonstrated in (Boudaoud [6]), but we now provide the prefactor. In terms of the constant aa, as defined by (11), we find

a=3δln⁡(3λeℓVEξ0),(27)a=3\delta\ln\left(\frac{3\lambda}{e\ell_{\mathrm{VE}}\xi_{0}}\right), \tag*{(27)}

which agrees well with the numerical solution at large ℓVE/λ\ell_{\mathrm{VE}}/\lambda (Figure 2(c), green dashed line). It justifies a posteriori that the equilibrium angle θe\theta_{e} does not play a role in this regime.

Applications

We now apply the viscoelastic contact line theory from the previous section to two paradigmatic wetting problems, namely drop spreading and dip coating. Classically, the interface profile in these problems can be described using matched asymptotics, where the Voinov contact line solution corresponds to the inner solution, matched to an outer solution at macroscopic scale. In this section, we briefly recall the outer solutions of the two problems, which are unaltered by viscoelasticity, and discuss the matching to the newly-derived viscoelastic inner solutions.

In applications such as drop spreading the contact line velocity UU is not a control parameter. Instead, the contact line velocity is determined through the matching procedure. Using the Cox-Voinov framework, an intrinsic velocity scale U∗U^{*} naturally arises by comparing the viscous and capillary term as

U∗=γθe3η,(28)U^{*}=\frac{\gamma\theta_{e}^{3}}{\eta}, \tag*{(28)}

which we will use as a rescaling velocity below. In these scaled units, we will see the appearance of a new dimensionless parameter

N0=(U∗Uψ)2=ψγθe4η2λs(29)N_0 = \left(\frac{U^*}{U_\psi}\right)^2 = \frac{\psi\gamma\theta_e^4}{\eta^2\lambda_s} \tag*{(29)}

This parameter governs the relative importance of viscosity and normal stress in the context of partially wetting flows. Alternatively, N0N_0 can be interpreted as a scaled normal stress coefficient, made dimensionless only with material parameters.

Drop spreading and retraction

We study the spreading (and retraction) of a drop, of volume Ω\Omega, over a solid surface (Figure 3). We consider drops smaller than the capillary length so that gravity can be ignored. The outer solution of the interface profile is obtained away from the contact line, where viscous and viscoelastic forces are not dominant. Therefore, at a given time, the shape adopted by the drop is close to the equilibrium shape of a static drop h0(r)h_0(r) as,

Figure 3. Drop spreading (a) and retraction (b)-(c). The schematic indicates the case, where the initial drop is drawn in black and the equilibrium shape in gray. The drop contact radius rescaled by the equilibrium contact radius is plotted as a function of dimensionless time for various N0N_0, corresponding to numerical solutions of (36), where c1=107c_1 = 10^7. The black dashed lines show the Newtonian solution for N0=0N_0 = 0, and the gray dotted line displays the viscoelastic retraction velocity, corresponding to (39) evaluated at the initial time. (c) The initial retraction velocity scaled by U∗U^* as a function of N0N_0, computed from (35) using Rinitial/Re=1.5R_{\mathrm{initial}}/R_e = 1.5 (as in panel (b)). The orange line in large N0N_0 regime corresponds to U∼ψ−1/2U \sim\psi^{-1/2} scaling as expected from equation (39).

h0(r)=2ΩπR2[1−(rR)2],(30)h_0(r) = \frac{2\Omega}{\pi R^2}\left[1-\left(\frac{r}{R}\right)^2\right], \tag*{(30)}

where the drop meets the solid at the apparent angle θapp,o=−h0′(r=R)\theta_{\mathrm{app},o}=-h_0'(r=R), which reads

θapp,o=4ΩπR3.(31)\theta_{\mathrm{app},o} = \frac{4\Omega}{\pi R^3}. \tag*{(31)}

As discussed before, close to the contact line (to be precise, the outer asymptotics of the inner region), the slope of an advancing contact line solution exhibits a logarithmic dependence with the distance. Hence the static equilibrium profile (3.3) cannot be matched directly to the Cox-Voinov theory. To resolve this issue, Hocking [25] showed that the first order correction to the outer solution in capillary number, defined as ηR˙/γ\eta\dot{R}/\gamma where R˙\dot{R} is the radius rate of change, takes the asymptotic form

h′3(x)=θapp,o3+9ηR˙γln⁡(xRb),(32)h'^3(x) = \theta_{\mathrm{app},o}^3 + 9\frac{\eta\dot{R}}{\gamma}\ln\left(\frac{x}{Rb}\right), \tag*{(32)}

for x=R−r≪Rx=R-r\ll R (see Figure 3(a)), and where b=1/(2e2)b=1/(2e^2). This solution is to be matched to the newly-derived viscoelastic inner solutions ((17)) and ((26)).

Spreading with weak viscoelasticity: partial wetting

For the partial wetting case, the drop spreads until the contact angle reaches the equilibrium contact angle θe\theta_e, or equivalently an equilibrium radius Re=(4Ω/(πθe))1/3R_e=(4\Omega/(\pi\theta_e))^{1/3}. For small capillary number, we can match the logarithmic dependencies of the outer solution ((32)) to the modified Cox-Voinov solution ((17)), which gives

(θapp,o)3=(θapp,i)3+9ηR˙γln⁡(Rθe6eλs).(33)(\theta_{\mathrm{app},o})^3 = (\theta_{\mathrm{app},i})^3 + 9\frac{\eta\dot{R}}{\gamma}\ln\left(\frac{R\theta_e}{6e\lambda_s}\right). \tag*{(33)}

As usual, the matching procedure connects the microscopic angle to the macroscopic angle, but now the microscopic angle contains viscoelastic effects. Inserting θapp,o\theta_{\mathrm{app},o} from the static solution ((31)) and θapp,i\theta_{\mathrm{app},i} from ((18)), we obtain an ODE for the drop radius R(t)R(t), as

(θapp,o)3=(4ΩπR3)3=θe3−34ψR˙2θeγλs+9ηR˙γln⁡(Rθe6eλs).(34)(\theta_{\mathrm{app},o})^3 = \left(\frac{4\Omega}{\pi R^3}\right)^3 = \theta_e^3 - \frac{3}{4}\frac{\psi\dot{R}^2\theta_e}{\gamma\lambda_s} + 9\frac{\eta\dot{R}}{\gamma}\ln\left(\frac{R\theta_e}{6e\lambda_s}\right). \tag*{(34)}

Finally, using dimensionless variables with bar as Rˉ=R/Re\bar{R}=R/R_e and tˉ=t/(Re/U∗)\bar{t}=t/(R_e/U^*), we can rewrite (34) as

34N0Rˉ2Rˉ˙−9ln⁡(c1Rˉ)Rˉ˙+(1Rˉ9−1)=0,(35)\frac{3}{4}N_0\bar{R}^{2}\dot{\bar{R}}-9\ln\left(c_1\bar{R}\right)\dot{\bar{R}}+\left(\frac{1}{\bar{R}^{9}}-1\right)=0, \tag*{(35)}

with c1=(Reθe)/(6eλs)c_1=(R_e\theta_e)/(6e\lambda_s). Here we recover the explicit dependency on N0N_0, which is the material parameter that for a given fluid quantifies normal stress effect.

Equation (35) is a second-order polynomial equation for Rˉ˙\dot{\bar{R}}, which we first solve to isolate Rˉ˙\dot{\bar{R}}, leading to

Rˉ˙=6ln⁡(c1Rˉ)N0[1−1−N027ln⁡2(c1Rˉ)(1Rˉ9−1)],(36)\dot{\bar{R}}=\frac{6\ln\left(c_1\bar{R}\right)}{N_0}\left[1-\sqrt{1-\frac{N_0}{27\ln^2\left(c_1\bar{R}\right)}\left(\frac{1}{\bar{R}^{9}}-1\right)}\right], \tag*{(36)}

and then integrate numerically. We notice that the second-order polynomial equation does not have a solution in real space for negative discriminant, which imposes a condition 27ln⁡2(c1Rˉ)>N0(1/Rˉ9−1)27\ln^2\left(c_1\bar{R}\right)>N_0(1/\bar{R}^{9}-1). Hence, in the spreading case, i.e. when Rˉ(tˉ=0)<1\bar{R}(\bar{t}=0)<1, we cannot find solutions for arbitrary large values of N0N_0. Mathematically speaking, the reason is that the apparent macroscopic angle versus UU has a maximum value when using the modified Cox-Voinov law. Therefore, if the outer geometry imposes an apparent macroscopic angle that is larger than this maximum, no contact-line speed can be found. The lack of solution is an artefact of the weak viscoelastic solution, which as also mentioned in the Discussion is resolved by admitting the strong viscoelastic solution (26).

In Figure 3(a) we show a typical solution of (36), with Rˉ(tˉ=0)=0.95\bar{R}(\bar{t}=0)=0.95 as an initial condition. Qualitatively, the normal stress effects speed up the spreading dynamics, although the quantitative change is very weak. This corroborates the conclusions of drop impact with polymer solutions, showing a weak dependence on the addition of polymers [1, 20, 36].

Spreading with strong viscoelasticity: (apparent) complete wetting

As shown in section 2.3, the advancing contact line dynamics at large velocities deviates from the modified Cox-Voinov law used in the previous subsection. In the drop spreading problem, if the initial radius is small, or equivalently the apparent angle is much larger than the equilibrium angle, then the contact-line speed is large and lies within the strongly viscoelastic regime. In this case, the inner solution for partially wetting substrates becomes completely independent of the equilibrium angle, and takes the form (26). Repeating the matching procedure with this strongly viscoelastic inner solution, the drop radius follows from

θapp,o3=9ηR˙γln⁡(RbℓVEξ0)=9ηR˙γln⁡(2ηRbψR˙ξ0).(37)\theta_{\mathrm{app,o}}^{3}=9\frac{\eta\dot{R}}{\gamma}\ln\left(\frac{Rb}{\ell_{\mathrm{VE}}\xi_{0}}\right)=9\frac{\eta\dot{R}}{\gamma}\ln\left(\frac{2\eta Rb}{\psi\dot{R}\xi_{0}}\right). \tag*{(37)}

This result is identical to that of a completely wetting viscoelastic drop; and it is of the same form as derived in Boudaoud [6].

During the spreading, which we initially assumed to be rapid, the contact line velocity will decrease in time. For partially wetting drops, this means that upon approaching the equilibrium angle, the strongly viscoelastic regime will give way to the weak regime discussed in the preceding paragraph.

For completely wetting surfaces, however, the drop radius follows a scaling law R∝t1/10R \propto t^{1/10} with logarithmic corrections, which is analogous to the Newtonian dynamics known as Tanner’s law [5, 16]. Using R∝t1/10R \propto t^{1/10} as an Ansatz, the ratio between contact line speed and drop radius inside the logarithm in (37) can be approximated as R˙/R≈1/(10t)\dot{R}/R \approx1/(10t). Inserting (31) into (37), and integrating, we obtain a modified Tanner’s law as

R≈(109(4Ωπ)3γηln⁡(c2ηtψ)t)1/10.(38)R \approx\left(\frac{10}{9}\left(\frac{4\Omega}{\pi}\right)^{3}\frac{\gamma}{\eta\ln\left(c_{2}\frac{\eta t}{\psi}\right)}t\right)^{1/10}. \tag*{(38)}

where c2=10/(e2ξ0)c_{2}=10/(e^{2}\xi_{0}). We note that the same equation has been derived using scaling arguments in Rafaï et al. [33]; Boudaoud [6], but we now provide a prefactor as derived for the second-order fluid. Again, the spreading of drops is accelerated by normal stress effects with respect to the Newtonian dynamics via the logarithmic term in (38).

Drop retraction

If the initial drop radius is above the equilibrium radius, the drop is retracting (see Figure 3(b)), for instance after an impact on a surface. Even though the contact line is now receding, the same framework as Section 3.1.1 can be used as long as the change in contact angle is sufficiently small (cf. Eggers [15] and the discussion on dip-coating). By consequence, (35) also governs the retraction dynamics of a partially wetting drop, but R˙\dot{R} is now negative. In the retraction case, the discriminant of the second-order polynomial equation is always positive such that one can find a solution for any N0N_{0}. Interestingly, viscoelastic effects now oppose the motion and slow down the retraction (see Figure 3(b)). In the large viscoelastic limit, for N0→∞N_{0}\to\infty, the viscous stress becomes negligible and the retraction velocity is set by balancing the normal stress and the capillary term of (34), which gives in dimensional form

R˙2=4γ(θe3−θapp,o3)λs3ψθe.(39)\dot{R}^{2}=\frac{4\gamma\left(\theta_{\mathrm{e}}^{3}-\theta_{\mathrm{app,o}}^{3}\right)\lambda_{\mathrm{s}}}{3\psi\theta_{\mathrm{e}}}. \tag*{(39)}

The dotted line in Figure 3(b) indicates the retraction as estimated using the viscoelastic receding speed (39), with the apparent angle taken from the initial condition. This provides a very good description of the retraction velocity for large N0N_0 (the contact line only slowing down upon approaching the equilibrium radius). The initial retraction velocity is plotted as a function of N0N_0 in Figure 3(c). In the small viscoelastic limit, quantified by small N0N_0, the viscoelastic term of equation (35) is subdominant and the retraction velocity typically scales with U∗U^*. Conversely, for large viscoelasticity, the retraction velocity is set by Uψ∼1/ψU_\psi\sim1/\sqrt{\psi}, leading to the scaling U/U∗∼N0−1/2U/U^* \sim N_0^{-1/2}, observed at large N0N_0 in Figure 3(c). Using the values of relevant parameters from the experiments by Bartolo et al. [1], we estimate N0N_0 to be in the range ∼103\sim10^3 to 10610^6. The N0N_0 values chosen in Figure 3(a)-(Figure 3b) fall within this range.

In the large viscoelastic limit, this retraction velocity scales with the inverse square root normal stress coefficient, as observed experimentally in Bartolo et al. [1]. These authors rationalised their experimental findings by using a phenomenological normal stress thin-film model and derived a retraction velocity of similar form as the one discussed here, namely R˙2=γ(θe2−θapp,o2)ℓ/(8ψ)\dot{R}^2=\gamma(\theta_e^2-\theta_{\mathrm{app},o}^2)\ell/(8\psi), where ℓ\ell is a microscopic cut-off length. Up to a prefactor, in the limit of θapp,o→0\theta_{\mathrm{app},o}\to0, this phenomenological equation agrees with the rigorous calculation provided here.

Forced wetting transition

We now turn to dip-coating, sketched in Figure 4(a), in which a plate is pulled out of a liquid bath at a constant speed UU. At small speed, the liquid-air interface is modified and the position of the contact line is shifted upward with respect to the equilibrium position. Above a critical speed UcU_c, however, there is no static contact line solution anymore and a Landau-Levich liquid film is entrained. This transition is usually called forced dewetting (Eggers [15]; Snoeijer et al. [41]; Chan et al. [8]; Galvagno et al. [18]).

Figure 4. Forced wetting transition: (a) Schematic of the dip-coating problem. Below the critical speed UcU_c (top), the contact line is displaced and the apparent contact angle is θapp,o\theta_{\mathrm{app},o}. Above the critical speed, a Landau-Levich film of thickness h∞h_\infty is entrained. (b) Critical dimensionless speed as function of dimensionless normal stress coefficient. The dots represents full scale numerical integration of (40), with θp/θe=1\theta_p/\theta_e=1 and λs/(ℓγθe)=10−4\lambda_s/(\ell\gamma\theta_e)=10^{-4}. The dashed line shows the asymptotic matching solution (44) based on the modified Cox-Voinov law.

The question we wish to address is how UcU_c is affected by viscoelasticity. We restrict ourselves to the case of small plate angle θp\theta_p, so that lubrication theory can be described for both the contact line and the bath. Assuming a stationary state, the interface position can then be computed from the lubrication equation as

γh′′′=3ηUh(h+3λs)−34(ψ(Uh+3λs)2)′+ρg(h′−θp).(40)\gamma h''' = \frac{3\eta U}{h(h+3\lambda_s)} - \frac{3}{4}\left(\psi\left(\frac{U}{h+3\lambda_s}\right)^2\right)' + \rho g(h'-\theta_p). \tag*{(40)}

With respect to (7), the sign of the viscous term is flipped as the contact line recedes, and a gravitational term has been added, ρ\rho and gg being the liquid density and gravitational acceleration respectively. The sign of the viscoelastic term is unchanged, as it is quadratic in contact line speed. The boundary conditions are

h(0)=0,h′(0)=θe,h′′(∞)=0,(41)h(0)=0,\qquad h'(0)=\theta_e,\qquad h''(\infty)=0, \tag*{(41)}

and are identical to those in § 2. In the Newtonian case, solutions only exist up to a critical velocity. Likewise, we have numerically determined UcU_c for the viscoelastic case by finding the maximum velocity for which (40), (3.14) admit a solution. A typical numerical result is shown as the circles in Figure 4(b)`, where we plot the normalised critical speed Uc/U∗U_c/U^* as a function of the viscoelastic parameter N0N_0. We thus observe that the normal stress effect lowers the critical speed of entrainment with respect to the Newtonian case (N0=0N_0=0). Like for droplet retraction dynamics, any receding contact line motion is inhibited by viscoelastic effects, now leading to an earlier entrainment.

Once again, these results can be described quantitatively from the modified inner solution for receding contact lines. The outer solution is again unaffected by viscoelasticity: far from the contact line position, the interface profile is found by balancing the hydrostatic pressure with the Laplace pressure. This leads to the equation of a static meniscus, which is entirely characterised by an apparent angle θapp,o\theta_{\mathrm{app},o} (see Figure 4(a)) and which corresponds to the outer solution of the full-scale problem. The inner solution close to the contact line, at scales much smaller than the capillary length ℓγ=γ/(ρg)\ell_\gamma=\sqrt{\gamma/(\rho g)}, does not involve gravity. Importantly, and in contrast to the advancing case, the general solution of the inner problem does not have a vanishing curvature at infinity. Therefore, the matching procedure is more intricate and analytical progress can be made by invoking an intermediate zone, for λ≪x≪ℓγ\lambda\ll x\ll\ell_\gamma, where slip and gravity are neglected, such that (40) reduces to the visco-capillary balance γh′′′=3ηU/h2\gamma h'''=3\eta U/h^2. The latter equation has an exact solution ([14]), which has a Voinov asymptotic behavior h′3=−9Caln⁡(x/ℓ)h'^3=-9\mathrm{Ca}\ln(x/\ell) at small xx and a constant curvature h′′→cteh''\to\mathrm{cte} at large xx. As shown in Eggers [15], this visco-capillary solution can be matched both to the outer static meniscus and to the slip region.

Hence, to understand the normal stress effects on dip-coating, which appear only on the slip-scale, the remaining task is to derive the slip-scale viscoelastic receding solution. Modifying the steps of § 2.2 along the lines of Eggers [15], but now including the normal stress term, we find that the large-xx asymptotic behavior of the viscoelastic inner solution follows

h′3=(θapp,i)3−9Caln⁡(exθe3λ).(42)h'^3=(\theta_{\mathrm{app},i})^3-9\mathrm{Ca}\ln\left(\frac{e x\theta_e}{3\lambda}\right). \tag*{(42)}

This result is identical to the advancing counterpart (17), with only a change of sign in the viscous term. Importantly, the only change with respect to the Newtonian case is a modification of the microscopic angle from θe\theta_e to the apparent microscopic angle defined in (18). Following Eggers [15], we find the equation for the critical speed:

θapp,i3=9ηUcγln⁡((ηUc/γ)1/3ℓγθe181/3π[Ai⁡(smax⁡)]2λsθp)(43)\theta_{\mathrm{app},i}^{3}=9\frac{\eta U_c}{\gamma}\ln\left(\frac{\left(\eta U_c/\gamma\right)^{1/3}\ell_{\gamma}\theta_e}{18^{1/3}\pi[\operatorname{Ai}(s_{\max})]^2\lambda_s\theta_p}\right) \tag*{(43)}

where Ai⁡(smax⁡)=0.53566…\operatorname{Ai}(s_{\max})=0.53566\ldots is the global maximum of the Airy function. The Newtonian result is recovered by replacing the left hand side by θe3\theta_e^3. Using the characteristic speed U∗U^* as a scale, the dimensionless critical velocity U‾c=Uc/U∗\overline{U}_c=U_c/U^* is the solution of

U‾c=1−34N0U‾c29ln⁡(c3U‾c1/3)(44)\overline{U}_c=\frac{1-\frac{3}{4}N_0\overline{U}_c^2}{9\ln\left(c_3\overline{U}_c^{1/3}\right)} \tag*{(44)}

where c3=1/(181/3π[Ai⁡(smax⁡)]2)(ℓγθe2)/(λsθp)≈0.423 (ℓγθe2)/(λsθp)c_3=1/(18^{1/3}\pi[\operatorname{Ai}(s_{\max})]^2)(\ell_\gamma\theta_e^2)/(\lambda_s\theta_p)\approx0.423\,(\ell_\gamma\theta_e^2)/(\lambda_s\theta_p). Here again, we recover the material parameter N0N_0 that quantifies viscoelasticity, as discussed earlier. Figure 4(b) shows excellent agreement between (44), shown as the dashed line, and the numerical solution. Hence, the decrease of the entrainment velocity with increasing viscoelasticity can be understood from the decrease of the apparent inner angle θapp,i\theta_{\mathrm{app},i}. In the limit of large N0N_0, one finds U‾c2≈4/(3N0)\overline{U}_c^2\approx4/(3N_0), which in dimensional units reads

Uc2≈4γθe2λs3ψ(45)U_c^2\approx\frac{4\gamma\theta_e^2\lambda_s}{3\psi} \tag*{(45)}

Note the similarity with (39) for drop retraction. This result suggests the emergence of a universal receding velocity for strong normal stress effect, independently of the outer geometry.

Discussion

In this paper we have studied the effect of viscoelastic normal stresses on contact line motion. Using the lubrication equation for the second-order fluid, we have derived a modified form of the classical Cox-Voinov theory: the macroscopic apparent contact angle (θapp,o\theta_{\mathrm{app},o}) is modified, due to a small-scale “apparent inner contact angle” (θapp,i\theta_{\mathrm{app},i}) that is lowered due to viscoelasticity both for advancing and receding contact line motion. Figure 5(a) shows the force balance for a fluid volume in the inner region close to the contact line, with the two dominant forces: capillary force and normal stress. The contribution of the normal stress on both lateral sides can be calculated by integrating the stress across the film thickness, and scales as ∼ψ(U/h)2h=ψU2/h\sim\psi(U/h)^2h=\psi U^2/h. Hence, the left side near the contact line is dominant as h→0h\to0, and the global effect of normal stresses is to pull towards the contact line, regardless of whether the contact line is advancing or receding. This explains why the normal stress facilitates advancing and inhibits receding motions. The singularity of the viscoelastic force as h→0h\to0 is regularized by the slip length λs\lambda_s, such that the effective resulting viscoelastic force is ψU2/λs\psi U^2/\lambda_s. This viscoelastic force in the inner region bends the interface and lowers the microscopic angle from θe\theta_e to θapp,i\theta_{\mathrm{app},i}. We have worked out quantitatively the effect on drop spreading, drop retraction and dip-coating, and found fundamental differences between advancing and receding contact lines. To summarise the findings, we turn to the schematics for the macroscopic apparent angle θapp,o\theta_{\mathrm{app},o} versus speed provided in Figure 5(b,Figure 5c).

Figure 5. (a) Force balance on a control volume, highlighted by the blue area, in the inner region near the contact line, where capillary force γ\gamma and the normal stress ψ(U/h)2\psi\left(U/h\right)^2 are balanced. Macroscopic apparent contact angle versus speed for receding (b) and advancing (c) contact lines. In the advancing case, we need to distinguish between weak and strong viscoelastic behavior. The crossover between these regimes is indicated schematically by the black solid line, and occurs around UψU_\psi defined in (2).

For receding contact lines, viscosity and normal stress provide forces that act in the same direction, both opposing the contact line motion. Both viscosity and normal stress give rise to a “bending” of the interface that tend to lower the macroscopic angle, as can be seen in Figure 5(b). As a result, the retraction velocity of a droplet and the critical velocity for dip-coating are lowered with respect to the Newtonian case. The relative importance of viscous and viscoelastic bending is governed by the parameter N0N_0 defined in (29). In the case of strong viscoelasticity, the second-order fluid model predicts a universal receding velocity (45), which is proportional to UψU_\psi defined in (2), that gives both the critical speed for dip-coating and droplet retraction. This prediction is consistent with experiments by Bartolo et al. [1], who in fact already introduced UψU_\psi to explain experimental measurements of droplet retraction after impact. Specifically, they found the retraction velocity to be proportional to 1/ψ1/\sqrt{\psi}. However, they found that the microscopic length appearing in UψU_\psi was tens of microns, which is much larger than a nanoscopic slip length. Bartolo et al. [1] remarked that the fitted lengths are comparable to the length of the fully extended polymer chains. Such large values of cutoff length may be due a shear-induced migration of the polymers which can lead to depletion layers (apparent slip lengths) in micrometers ([31, 17, 12, 37] (Ma & Graham 2005)). In general, non-hydrodynamic interaction between polymers and the surface can also contribute to large slip lengths ([29, 21]). Regardless of the molecular mechanisms at play, we expect that such effects do not alter the phenomenology discussed here, including the interpretation in terms of an apparent inner angle θapp,i→0\theta_{\mathrm{app},i} \to0 due to viscoelasticity. The presented theory provides a benchmark for the influence of normal stress

on receding contact line motion, but molecular mechanisms might be required to provide an effective scale of regularisation.

For advancing contact lines, viscosity and normal stress provide forces that act in opposite directions: the normal stress actually facilitates contact line motion. We have seen that we need to distinguish between weak and strong viscoelasticity. For weak viscoelasticity, there is a non-monotonic dependency of the macroscopic angle on contact line velocity, as indicated by the orange dashed line in Figure 5(c). The maximum arises due to a competition between viscous bending (increasing the angle) and viscoelastic bending (decreasing the angle). The crossover to the strongly viscoelastic regime is given by U∼UψU \sim U_\psi (see (19)), which occurs when the normal stress effect is so strong that it bends the interface to form a precursor film of typical size ℓVE\ell_{\mathrm{VE}}. This strongly viscoelastic regime is indicated by the dashed blue line, and can be interpreted as an “apparent complete wetting”, since the contact line motion becomes completely insensitive to θe\theta_e. The crossover is schematically indicated by the black solid line. The exact details of the crossover from weak to strong viscoelasticity are not universal, but depend on the material parameter N0N_0 defined in (29). For example, the speed at which the maximum appears in the weakly viscoelastic regime scales as Uψ/N0U_\psi/\sqrt{N_0}; when N0N_0 is sufficiently large the maximum will thus emerge well before it is erased by the apparent complete wetting regime.

The presented analysis provides concrete predictions for experiments on wetting of viscoelastic liquids, rooted in a systematic long-wave expansion of the second-order fluid. Our findings suggest the possibility of a non-monotonic dependence of the contact angle with advancing velocity, which could potentially lead to instabilities. Such effects remain to be explored experimentally, but also deserve some further theoretical analysis. Namely, the calculations are based on the second-order fluid: while this lubrication model is equivalent to that obtained with Oldroyd-B fluid when viscoelasticity is introduced perturbatively ([10] (Ro & Homsy 1995)), its quantitative validity at strong viscoelasticity remains to be explored, more so when polymers in moving contact line problems have been observed to be strongly stretched ([39, 37]). It would therefore be of interest to study contact line motion for a variety of constitutive models.

Acknowledgements. The authors gratefully acknowledge discussions with Daniel Bonn and Satish Kumar.

Funding. This work was supported by NWO through VICI grant no. 680-47-632.

Declaration of interests. The authors report no conflict of interest.

Author ORCIDs. Minkush Kansal: https://orcid.org/0000-0003-1584-3775; Vincent Bertin: https://orcid.org/0000-0002-3139-8846; Charu Datt: https://orcid.org/0000-0002-9686-1774; Jens Eggers: https://orcid.org/0000-0002-0011-5575; Jacco H. Snoeijer: https://orcid.org/0000-0001-6842-3024.

References

  1. [1]Bartolo, Denis, Boudou, Arezki, Narcy, Grégoire & Bonn, Daniel 2007 Dynamics of non-newtonian droplets. Physical review letters 99 (17), 174502.pubmed.ncbi.nlm.nih.gov/17995337
  2. [2]Bender, Carl M & Orszag, Steven A 1999 Advanced mathematical methods for scientists and engineers II: Asymptotic methods and perturbation theory, vol. 1. Springer Science & Business Media.
  3. [3]Bergeron, Vance, Bonn, Daniel, Martin, Jean Yves & Vovelle, Louis 2000 Controlling droplet deposition with polymer additives. Nature 405 (6788), 772–775.pubmed.ncbi.nlm.nih.gov/10866193
  4. [4]Biance, Anne-Laure, Clanet, Christophe & Quéré, David 2004 First steps in the spreading of a liquid droplet. Phys. Rev. E 69, 016301.pubmed.ncbi.nlm.nih.gov/14995706
  5. [5]Bonn, Daniel, Eggers, Jens, Indekeu, Joseph, Meunier, Jacques & Rolley, Etienne 2009 Wetting and spreading. Reviews of modern physics 81 (2), 739.DOI
  6. [6]Boudaoud, Arezki 2007 Non-newtonian thin films with normal stresses: dynamics and spreading. The European Physical Journal E 22, 107–109.pubmed.ncbi.nlm.nih.gov/17377751
  7. [7]Bouillant, Ambre, Dekker, Pim J, Hack, Michiel A & Snoeijer, Jacco H 2022 Rapid viscoelastic spreading. Physical Review Fluids 7 (12), 123604.
  8. [8]Chan, Tak Shing, Snoeijer, Jacco H & Eggers, Jens 2012 Theory of the forced wetting transition. Physics of fluids 24 (7).DOI
  9. [9]Cox, R. G. 1986 The dynamics of the spreading of liquids on a solid surface. part 1. viscous flow. Journal of Fluid Mechanics 168, 169–194.DOI
  10. [10]Datt, Charu, Kansal, Minkush & Snoeijer, Jacco H 2022 A thin-film equation for a viscoelastic fluid, and its application to the landau–levich problem. Journal of Non-Newtonian Fluid Mechanics 305, 104816.
  11. [11]De Corato, M., Greco, F. & Maffettone, P. L. 2016 Reply to “Comment on ‘Locomotion of a microorganism in weakly viscoelastic liquids’ ”. Phys. Rev. E 94, 057102.
  12. [12]Degré, Guillaume, Joseph, Pierre, Tabling, Patrick, Lerouge, Sandra, Cloitre, Michel & Ajdari, Armand 2006 Rheology of complex fluids by particle image velocimetry in microchannels. Applied Physics Letters 89 (2), 024104, arXiv: https://pubs.aip.org/aip/apl/article-pdf/doi/10.1063/1.2221501/14358247/024104_1_online.pdf.
  13. [13]Doedel, Eusebius J, Champneys, Alan R, Dercole, Fabio, Fairgrieve, Thomas F, Kuznetsov, Yuri A, Oldeman, B, Paffenroth, RC, Sandstede, B, Wang, XJ & Zhang, CH 2007 Auto-07p: Continuation and bifurcation software for ordinary differential equations .
  14. [14]Duffy, BR & Wilson, SK 1997 A third-order differential equation arising in thin-film flows and relevant to tanner’s law. Applied Mathematics Letters 10 (3), 63–68.
  15. [15]Eggers, Jens 2005 Existence of receding and advancing contact lines. Physics of Fluids 17 (8), 082106.DOI
  16. [16]Eggers, Jens & Fontelos, Marco Antonio 2015 Singularities: formation, structure, and propagation, , vol. 53. Cambridge University Press.DOI
  17. [17]Fang, Lin, Hsien, Chih-Chen & Larson, Ronald G 2007 Molecular imaging of shear-induced polymer migration in dilute solutions near a surface. Macromolecules 40 (23), 8490–8499.
  18. [18]Galvagno, M, Tseluiko, D, Lopez, H & Thiele, U 2014 Continuous and discontinuous dynamic unbinding transitions in drawn film flow. Physical review letters 112 (13), 137803.
  19. [19]de Gennes, Pierre-Gilles, Brochard-Wyart, Françoise & Quéré, David 2004 Capillarity and wetting phenomena: drops, bubbles, pearls, waves. Springer.
  20. [20]Gorin, Benjamin, Di Mauro, Gabrielle, Bonn, Daniel & Kellay, Hamid 2022 Universal aspects of droplet spreading dynamics in newtonian and non-newtonian fluids. Langmuir 38 (8), 2608–2613.
  21. [21]Gupta, Siddhartha & Vanapalli, Siva A. 2020 Microfluidic shear rheology and wall-slip of viscoelastic fluids using holography-based flow kinematics. Physics of Fluids 32 (1), 012006, arXiv: https://pubs.aip.org/aip/pof/article-pdf/doi/10.1063/1.5135712/15795495/012006_1_online.pdf.
  22. [22]Guyard, Gabriel, Vilquin, Alexandre, Sanson, Nicolas, Jouenne, Stéphane, Restagno, Frédéric & McGraw, Joshua D 2021 Near-surface rheology and hydrodynamic boundary condition of semi-dilute polymer solutions. Soft Matter 17 (14), 3765–3774.
  23. [23]Han, Jeongin & Kim, Chongyoup 2013 Spreading of boger fluid on horizontal surface. Journal of Non-Newtonian Fluid Mechanics 202, 120–130.
  24. [24]Han, Jeongin & Kim, Chongyoup 2014 Theoretical and experimental studies on the contact line motion of second-order fluid. Rheologica Acta 53, 55–66.
  25. [25]Hocking, LM 1983 The spreading of a thin drop by gravity and capillarity. The Quarterly Journal of Mechanics and Applied Mathematics 36 (1), 55–69.DOI
  26. [26]Huh, Chun & Scriven, Laurence E 1971 Hydrodynamic model of steady movement of a solid/liquid/fluid contact line. Journal of colloid and interface science 35 (1), 85–101.
  27. [27]Kim, Jeong-Hyun & Rothstein, Jonathan P. 2015 Dynamic contact angle measurements of viscoelastic fluids. Journal of Non-Newtonian Fluid Mechanics 225, 54–61.
  28. [29]Mhetar, Vijay & Archer, LA 1998 Slip in entangled polymer melts. 1. general features. Macromolecules 31 (24), 8607–8616.DOI
  29. [30]Morozov, A. & Spagnolie, S. E. 2015 Introduction to complex fluids. In Complex Fluids in Biological Systems, pp. 3–52. Springer.DOI
  30. [31]Müller-Mohnssen, H., Weiss, D. & Tippe, A. 1990 Concentration dependent changes of apparent slip in polymer solution flow. Journal of Rheology 34 (2), 223–244, arXiv: https://pubs.aip.org/sor/jor/article-pdf/34/2/223/12638237/223_1_online.pdf.
  31. [32]Oron, Alexander, Davis, Stephen H & Bankoff, S George 1997 Long-scale evolution of thin liquid films. Reviews of modern physics 69 (3), 931.DOI
  32. [33]Rafaï, Salima, Bonn, Daniel & Boudaoud, Arezki 2004 Spreading of non-newtonian fluids on hydrophilic surfaces. Journal of Fluid Mechanics 513, 77–85.DOI
  33. [36]Sen, Uddalok, Lohse, Detlef & Jalaal, Maziyar 2022 Elastocapillary worthington jets. arXiv preprint arXiv:2207.07928.arxiv.org/abs/2207.07928
  34. [37]Shin, Hongrok, Bong, Ki Wan & Kim, Chongyoup 2016 Depletion of lambda-dna near moving contact line. Journal of Non-Newtonian Fluid Mechanics 236, 50–62.DOI
  35. [38]Shin, Hongrok & Kim, Chongyoup 2015 Contact line motion of polymer solution inside capillary. Journal of Non-Newtonian Fluid Mechanics 218, 62–70.DOI
  36. [39]Smith, Mi & Bertola, V 2010 Effect of polymer additives on the wetting of impacting droplets. Physical review letters 104 (15), 154502.
  37. [40]Snoeijer, Jacco H & Andreotti, Bruno 2013 Moving contact lines: scales, regimes, and dynamical transitions. Annual review of fluid mechanics 45, 269–292.
  38. [41]Snoeijer, Jacco H, Andreotti, Bruno, Delon, Giles & Fermigier, Marc 2007 Relaxation of a dewetting contact line, part 1. a full-scale hydrodynamic calculation. Journal of Fluid Mechanics 579, 63–83.
  39. [42]Snoeijer, Jacco H & Eggers, Jens 2010 Asymptotic analysis of the dewetting rim. Physical Review E 82 (5), 056314.
  40. [43]Tanner, Roger I 2000 Engineering rheology, vol. 52. OUP Oxford.
  41. [44]Voinov, OV 1976 Hydrodynamics of wetting. Fluid dynamics 11 (5), 714–721.DOI
  42. [46]Wang, Yuli, Do-Quang, Minh & Amberg, Gustav 2017 Impact of viscoelastic droplets. Journal of Non-Newtonian Fluid Mechanics 243, 38–46.
  43. [47]Wang, Yuli, Minh, Do-Quang & Amberg, Gustav 2015 Dynamic wetting of viscoelastic droplets. Physical Review E 92 (4), 043002.DOI
  44. [49]Wei, Y, Ramé, E, Walker, LM & Garoff, S 2009b Dynamic wetting with viscous newtonian and non-newtonian fluids. Journal of Physics: Condensed Matter 21 (46), 464126.
  45. [51]Yada, Susumu, Bazesefidpar, Kazem, Tammisola, Outi, Amberg, Gustav & Bagheri, Shervin 2023 Rapid wetting of shear-thinning fluids. Physical Review Fluids 8 (4), 043302.arxiv.org/abs/2208.11410
  46. [52]Yue, Pengtao & Feng, James J. 2012 Phase-field simulations of dynamic wetting of viscoelastic fluids. Journal of Non-Newtonian Fluid Mechanics 189-190, 8–13.
  47. [53]Zang, Duyang, Wang, Xiaolu, Geng, Xingguo, Zhang, Yongjian & Chen, Yongmei 2013 Impact dynamics of droplets with silica nanoparticles and polymer additives. Soft Matter 9 (2), 394–400.

Paper details

vlnc:W_wmuxpskr
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents